Ecco Instruction Guide
Contents
1. and its digital compass requires calibration to more accurately navigate the return It is required for first time use thereafter whenever you take Ecco farther than 100 mi or 161 km Note Whenever instructed to press and hold a button press down for at least 3 seconds 1 While Ecco is in Ready mode hold it face up then press and hold location 1 e6 until the LCD message Hold flat and press lock appears then press and release lock button e3 Copyright 2008 IDC Design Corporation All Rights Reserved 5 AID ecco QP DESIGN CORPORATION 2 The LCD message changes to Turn 180 around and press lock Keep Ecco face up while turning it completely around toward the opposite direction then press and release lock button e3 6 Copyright 2008 IDC Design Corporation All Rights Reserved ID ecco QP DESIGN CORPORATION 3 The LCD message changes to Turn over and press lock Place but do not press your finger on the lock button e3 as you flip Ecco face down then press and release lock button e3 4 Turn Ecco face up to read the LCD message Calibrate complete After 5 seconds the message changes to Ready Copyright 2008 IDC Design Corporation All Rights Reserved 7 DESIGN CORPORATION Amc ecco Optional Change Distance Unit System You have the option to change the distance unit system from English feet ft miles mi to metric meters2. is connected Occasionally the arrow may not display for a brief moment for example if you put Ecco in your purse or pocket while navigating then pull it out However if the arrow does not appear after 1 2 minutes Ecco needs to be calibrated It is required for first time use and thereafter whenever you take Ecco farther than 100 mi or 161 km When instructed to press and hold a button do so for at least 3 seconds otherwise Ecco reverts to the Ready mode with no changes made Ecco remains on and active as long as it is acquiring GPS data to update the direction and distance infor mation and you are moving more than 30 ft or 9 m every 5 minutes If not the LCD message No Movement appears and Ecco goes to Sleep Yes After you power it on to Ready mode simply press return button e4 and Ecco will resume the last course toward your selected location The location remains in memory until it is replaced with a new locked position Copyright 2008 IDC Design Corporation All Rights Reserved 13 Ai c ecco os DESIGN CORPORATION Why doesn t Ecco You can turn Ecco Off only during the Searching turn Off when I mode or start up Incidentally Ecco will time out to hold down the Off after 5 hours and 15 minutes in Sleep mode Power button Why don t the The distance and times provided in the Ecco distance and Instruction Guide are approximate measurements times exactly match the ones in the instr
3. or 8 days on standby 1 Connect the charging cable into the USB port e5 from one of the following power sources AC outlet vehicle 12v power outlet personal computer USB port or an auxiliary power pack see Power Source Specifications on page 16 2 The LCD backlight turns on and the message on the LCD reads Charging After 5 seconds the backlight turns off 3 When charged the message on the LCD changes to Battery Charged 4 Disconnect the charging cable from the USB port e5 Ecco s features cannot be accessed while connected to the charging cable Ecco can detect a low battery level below a threshold of 25 however the low battery icon appears on the LCD only during the Ready Searching or Return modes Power On to Ready Mode 1 Press and hold power on off e1 for 2 3 seconds The LCD backlight turns on and the start up screen appears 2 Ecco immediately starts acquiring GPS data indicated by the GPS status indicator e2 blinking green and the LCD displaying a blinking satellite icon and the message Searching 3 When your current position is determined the GPS status indicator e2 becomes a steady D Copyright 2008 IDC Design Corporation All Rights Reserved AID ecco QP DESIGN CORPORATION green The satellite icon on the LCD disappears and a sequence of messages appears Initializing gt Ready Calibrate Important Do Not Skip Ecco stores magnetic field inputs
4. product or from defects in the product Some states do not allow the exclusion of incidental or consequential damages so the stated limitations may not apply therein FCC Notice Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This device generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help IDC Contact Information IDC Design Corp 3002 Dow Ave Ste 410 Tustin CA 92780 7236 888 804 GPS8 4778 www idcgps com Patent 7 233 863 Model IDC 80001 001 2 Copyright 2008 IDC Design Corporatio
5. IDC ecco Instruction Guide Personal Pocket GPS Locator MORE HELP AND SUPPORT FOR SERVICE AND INSTRUCTION PLEASE GO TO WWW I Copyright 2008 IDC Design Corporation All Rights Reserved hc DESIGN CORPORATION Notices and Specifications About GPS System amp Location Accuracy The Global Positioning System GPS is operated by the US government which is solely responsible for its accuracy and maintenance The system is subject to changes which could affect the accuracy and performance of all GPS equipment In addition the GPS system itself limits the accuracy of the distance indicated on the device s display to within approximately 3 5 meters of the actual saved location About GPS Signals This device must acquire GPS satellite signals to operate The device may not be able to acquire signals if located indoors or near tall obstructions such as trees or tall buildings Go to an area free from tall obstructions to use the device When the device acquires satellite signals the green LED indicator is steady When it loses satellite signals you are traveling away from the a stored active location or the device cannot acquire a GPS signal the LED is red This product is designed to provide direction to a saved location It is not designed as a monitoring device for tall obstructions hazardous or weather conditions or other factors that may affect safety while using this device For more information about GPS visit IDC Design C
6. ars on the LCD Distance Units Displayed on the LCD Less than 2 640 ft foot ft Less than 500 m meter m 2 640 ft up to 99 99 mi 0 01 mi 500 m up to 99 99 km 0 01 km 100 mi up to 9 999 mi mile mi 100 km up to 9 999 km kilometer km When navigating toward a location the LCD displays the nearest whole or hundredth of a unit measurement depending on the distance from the location Copyright 2008 IDC Design Corporation All Rights Reserved 11 Ai c ecco os DESIGN CORPORATION Why is Searching completed quickly sometimes and takes longer other times What can be done when Ecco has difficulty finding a GPS Signal Why does the arrow point toward metal buildings or power lines when my location is not in that direction Why does the Red light LED blink and Ecco go to Sleep when I am navigating back to my location How long does it take to charge the battery How long does the charge last FAQs Searching will be completed quickly when Ecco is activated from the Sleep mode If Ecco is activated from the Off state Searching may take up to 2 minutes to acquire a satellite signal To ensure the most effective way for Ecco to search for a satellite signal hold Ecco face up toward the open sky Move away from tall buildings trees or overhead obstructions The digital compass may be affected by large metal objects such as buildings with metal power lines and steel b
7. m kilometers km or back again 1 While Ecco is in Ready mode press and hold location 3 e6 for 3 seconds through a sequence of messages Hold to change units gt Units set to meters feet 2 Release location 3 e6 The LCD message Ready appears Note Repeat the previous steps to change back Navigating with Ecco Store a Location 1 While Ecco is in Ready mode press lock button e3 The LCD message Select loca tion appears 2 Press location e6 to store your current position then the message Location locked appears Proceed to your destination Note After 1 minute Ecco goes to Sleep but your stored location will not be lost It will remain in memory until it is replaced with a new locked posi tion See Sleep Versus Off on page 9 Return to a Location 1 To wake Ecco from Sleep press Power for 1 second or until the LCD backlight comes on The LCD message Ready appears 2 To navigate to e Last locked position simply press return button e4 e Another stored position press return button e4 and location e6 8 Copyright 2008 IDC Design Corporation All Rights Reserved DESIGN CORPORATION Amc ecco 3 Follow the directional arrow d4 on the LCD toward the active location d7 if there is no arrow see FAQs on page 12 Other informa tion displayed on the LCD includes compass direction d5 and distance d6 Note Ecco remains on and active as long as it is acq
8. moved IDC reserves the right to charge for service IDC is not responsible for any loss or damage to the product while it is in transit The replacement or repaired product is warranted for 30 days from the date of the return shipment or for the warranty days balance from the original date of purchase whichever is longer This limited warranty does not apply to damages caused by misuse abuse negligence improper handling accident alteration or repair not authorized by IDC as well as the use of a non compliant power device YOUR EXCLUSIVE REMEDY UNDER THIS WRITTEN LIMITED WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT AT IDC S OPTION OF ANY DEFECTIVE PART COVERED BY THIS LIMITED WARRANTY THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE STATUTORY OR OTHERWISE YOU HAVE SPECIFIC LEGAL RIGHTS WITH THIS LIMITED WARRANTY AND MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN NO EVENT SHALL IDC BE LIABLE FOR ANY INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER RESULTING FROM THE USE MISUSE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT IN NO EVENT SHALL IDC S RESPONSIBILITY EXCEED REPLACEMENT OF THE PRODUCT Some states do not allow the exclusion of incidental or consequential damages so the above limitations may n
9. n All Rights Reserved O TM i SIDC ecco l Find your way back e1 power on off e2 GPS status indicator d1 active GPS indicator F d2 low battery icon d3 proximity ring d4 directional arrow d6 distance d7 active location d5 compass direction e3 lock button e4 return button e5 USB port e6 location buttons e7 key ring el Press 3 seconds to power On or Off di Indicates GPS searching 1 second to wake or put to Sleep e2 Lights green for communication or d2 Appears when the battery is low red for no GPS signal off course opposite direction or no movement e3 Press to store current location d3 Shows rings in a pattern depending on proximity e4 Press to start return to last locked or d4 Points toward active location other location e5 Insert the battery cable d5 Indicates compass direction toward active location e6 Store up to 3 locations 1 also used d6 Shows distance unit in ft mi or for calibration 3 also used to change m km to active location distance unit e7 Use to attach keys d7 Shows active return location Copyright 2008 IDC Design Corporation All Rights Reserved 3 DESIGN CORPORATION Amc ecco Before You Begin Note The distance and times provided in this instruction guide are approximate measurements Charge the Battery It takes 2 hours to fully charge the battery The charge lasts 5 hours with typical use during active tracking
10. orporation s Web site www idcgps com Warning This handheld device is only intended to be used as a supplemental navigation aide The user assumes all responsibilities associated with the use of this product It must not be used for any purpose requiring precise measurement of location direction distance or topography This device should not be used for navigating any aircraft or vehicles It is the user s sole responsibility to exercise proper judgment when using this product under any conditions Vehicle Use Notice IDC is committed to safety and responsible use Do not use this GPS device to navigate while driving a motor vehicle Attention to this device while driving can distract the motor vehicle s operator creating an unsafe situation Injury death or property damage may result if the operator fails to adhere to safe driving practices It is the driver s sole responsibility to operate the vehicle in a safe manner The device should not be mounted in a vehicle in a manner to distract impair the view or in any way interfere with the motor vehicle s operator or the motor vehicle s safety features such as an air bag Windshields and vehicle windows integrated with metallic materials such as defrosters or tinting film can degrade GPS reception inside a vehicle Liability Notice In no event will IDC be liable for any incidental special indirect or consequential damages resulting from the use misuse or inability to use this
11. ot apply to you Contact your local dealer for limited warranty information for products purchased outside the USA Sales and service 888 804 GPS8 4778 www idcgps com Copyright 2008 IDC Design Corporation All Rights Reserved 15 Amc ecco os DESIGN CORPORATION Battery Warnings If these guidelines are not followed the internal lithium ion battery may experience a shortened life span or may present a risk of damage to the GPS unit fire chemical burn electrolyte leak and or injury e Do not leave the unit exposed to a heat source or in a high temperature location such as in the sun e Do not puncture or incinerate e Do not operate the unit outside of the following temperature range 32 F 113 F 0 C 45 C e When storing the unit for an extended time store within the following temperature range 14 F 113 F 10 C 45 C e Do not attempt to remove the battery To replace battery contact IDC directly at www idcgps com e Do not dispose of this product in regular waste Power Source Specifications The following approved power sources must be used under the conditions of Ecco s warranty e AC travel wall adapter input 100 240 VAC 50 60 Hz 0 15A output 5 0V 0 7A rated UL CE e Car adapter input 12V output 5 0V e Standard computer USB 2 0 cable e Auxiliary 5V power pack 16 Copyright 2008 IDC Design Corporation All Rights Reserved
12. ridges Move away from these types of objects when using Ecco The Red light blinks when Ecco is not traveling in the general direction of the arrow and will go to Sleep after approximately 2 minutes Press the power button e1 and then the return button e4 to continue your navigation HINT While going around an obstacle to get to your location rotate Ecco in your hand so that the directional arrow points to the 12 0 clock position if you do not want it to go to Sleep It takes 2 hours to fully charge the battery The charge lasts 5 hours during active tracking or 8 days on standby 12 Copyright 2008 IDC Design Corporation All Rights Reserved Al c ecco os DESIGN CORPORATION How can I tell if the battery is low Why aren t Ecco s features acces sible Why is the LCD directional arrow missing during the return When do I need to calibrate Ecco Why is the cali bration or unit change unsuc cessful Does Ecco stay on while navigating Will Ecco remember the selected location if it goes to Sleep while navigating Can I delete a stored location Ecco can detect a low battery level below a threshold of 25 However the low battery icon appears on the LCD only during the Ready Searching or Return modes Ecco may need to be charged or if fully charged it may still be connected to the charging cable None of Ecco s features are accessible if the charging cable
13. uctions 14 Copyright 2008 IDC Design Corporation All Rights Reserved Ai c ecco os DESIGN CORPORATION 1 Year Limited Warranty This Ecco Personal Pocket GPS Locator limited warranty covers defects in mate rial and workmanship when you properly maintain the product under normal use for a period of 1 year from the date of purchase This limited warranty does not cover the IDC supplied power device This product must be used with the IDC supplied power device or a power device that is compliant with the specifications listed in the User Guide see Power Source Specifications on page 16 Use with any other power device voids this limited warranty A product which is defective in material or workman ship will at IDC s option be replaced or repaired at no charge to you for parts or labor To obtain this limited warranty service obtain a Return Materials Authorization RMA number prior to shipping by submitting a repair request through IDC s Web site at www idcgps com Pack the product securely in a shipping container with the RMA number clearly written on the outside of the package Send the product shipping charges prepaid to the authorized IDC Service Center address provided with the RMA number Include the following required item e Receipt with the date of purchase or a dated bill of sale If the sales receipt is not provided is illegible or incomplete or if the product serial number is altered or re
14. uiring GPS data to update the direction and distance information and you are moving more than 30 ft or 9 m every 5 minutes If not the LCD message No Movement appears and Ecco goes to Sleep Repeat step 1 to wake Ecco up When in Ready mode press return button e4 and Ecco will resume the last course toward your selected location 4 If you travel off course that is more than 22 5 are headed in the opposite direction or the distance d6 is increasing the GPS status indicator e2 flashes red 5 Inthe vicinity of 80 ft or 24 m from the active location d7 the proximity ring d3 blinks alternating large and small rings 6 In the vicinity of 20 ft or 6 m the LCD reads Found and the proximity ring d3 blinks large and small rings simultaneously 7 After arriving you can either select another location or simply do nothing Ecco automati cally goes to Sleep after 2 minutes in the Found mode see Sleep Versus Off on page 9 Additional Information Sleep Versus Off In both the Sleep mode and the Off state the LCD backlight and LEDs are dark The main difference is that in Sleep mode Ecco attempts to refresh GPS positioning data up to 3 times within a period of 5 Copyright 2008 IDC Design Corporation All Rights Reserved 9 Ai c ecco os DESIGN CORPORATION hours and 15 minutes The other difference is the LCD message that appears as Ecco shuts down either Sleep or Off Note After 5 ho
15. urs and 15 minutes in Sleep mode Ecco times out to the Off state Ecco will automatically go to Sleep if e You do nothing for 1 minute while one of these messages appears on the LCD Ready Select location Location 1 2 or 3 selected e You do nothing after Found is displayed on the LCD for about 2 minutes e Searching displays on the LCD for about 2 minutes then the message No GPS appears on the LCD and the GPS status indicator e2 is a steady red e Traveling more than 2 minutes off course more than 22 5 headed in the opposite direction or distance d6 is increasing and the GPS status indicator e2 is a blinking red e No GPS data is received for about 5 minutes while the message No GPS appears on the LCD and the GPS status indicator e2 is a steady red e There is no change in the GPS data for about 5 minutes while the message No Movement appears on the LCD and the GPS status indi cator e2 is a steady red You can manually put Ecco to Sleep or turn the device Off by pressing power on off e1 The difference is the length of time you press and hold the button e To put Ecco to Sleep press and hold power on off e1 until the LCD message Sleep appears e You can turn Ecco Off only during the Searching mode or at start up press and hold 10 Copyright 2008 IDC Design Corporation All Rights Reserved A c ecco os DESIGN CORPORATION power on off e1 until the message Off appe
Download Pdf Manuals
Related Search