Outdoor Dome KCM Series Hardware Manual
Contents
1. ACT Connecting Vision vA Hardware Manual Manually adjust the IP addresses of multiple cameras If there are more than one camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility 9 IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 Basic Search T O Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Save amp Reboot a a Account Password 123456 Http Port IP Address MAC Address FW Version Model Serial No Multicast IP Status 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric Camera KCM3911 228 5 6 1 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCM1111 228 5 6 1 172 16 26 6 00 NA ra KCM7311 228 5 6 1 172 16 26 7 00 TCM6630 228 5 6 1 172 16 26 10 00 Dynamic IP Address TCM4201 228 5 6 1 172 16 26 11 00 KCM3911 228 5 6 1 172 16 26 13 00 KCM5111 228 5 6 1 172 16 26 40 00 KCM5211 228 5 6 1 172 16 26 41 00 i KCM5311 228 5 6 1 172 16 26 50 00 r 8 KCM5111 228 5 6 1 172 16 26 52 00 _KcM5311 228 5 6 1 172 16 26 53 00 J TCM5311 228 5 6 1 172 16 26 54 00 TCM5611 228 5 6 1 172 16 262. ACTI Connecting Vision vA Hardware Manual Other Adjustments eneen nennen 27 How to Adjust Focus and Viewing Angle annenansenansennn 27 KON Ze KONE IT eran E 27 A ses gsc css oc sees cg ssa eee eae eae sect eee eeeececeessene cgecuees 29 Accessing the Camera aaneen nenenen 30 Connect the Equipment zamen btn 30 Configure the IP Addresses ccsssseeseeseeseeseecenseecenseesenseeenseseenseseens 30 ACCESS Ne CIMETA rense EEEE 35 3 www acti com D4 ACTi Connecting Vision Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you find any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to make chan
3. Outdoor Dome KCM Series Hardware Manual KCM 7311 KCM 7211 KCM 7111 2013 11 01 ACTI Connecting Vision WA lt gt Pp ACTI Connecting Vision Hardware Manual Table of Contents EC al g o P nnen nnn A Safety Instructions asssssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn dee 5 I OGUGON nicnn aaa 6 Packade COMENTS mmm ennen benen sene merken Ene 6 PNYSICAl DESCHPHON sssini aaa EE Si 7 Mounting Solutions onnnsnnnnrennnnr nennen ennen enanenennnenennnenennneneen 9 Installing the Camera on a Surface 10 Step 1 Drill the HOES nennen eeeh nee 10 Step 2 Open the Dome COVER accssiccsscacacancascseascecnsescanevenaneenscecusersnncusenvaees 11 Step 3 Prepare for Waterproof Installation eenen 12 Waterproof Solution with Naked Cable nanne 13 Waterproof Solution with Conduit un anann eneen en enenen vennen 15 Step 4 Install the Camera to the Surface ann nnanennanennanenn 19 Step 5 Connect the Cable S nonnen ennen eenen eenenseneneen 19 Step 6 Access the Camera Live VIEW ennnann enne nnanenn 20 Step 7 Adjust the Viewing Angle and FOCUS naaar nnen 20 Step 8 Close the Dome COVe r nnen enen nnanen nare nnnm 20 Other Connections nanne nennen nennennenn 21 Connecting a Power Adapter Optional nee 21 Connecting DI DO Devices Optional eene nnenn 23 Connecting Audio In Out Devices Optional een 26 2 www acti com
4. flexible conduit not included in the package For use with an Exterior grade Ethernet cable not included in the package For use with 1 2 flexible conduit not included in the package NOTE The bundled conduit gland may vary Check the conduit gland that came with your package to determine if 3 8 or 1 2 is the suitable flexible conduit size www acti com Pq ACTI Connecting Vision Hardware Manual Waterproof Solution with Naked Cable This section describes the procedures in using the bundled cable gland and an exterior grade Ethernet cable 1 Disassemble the cable gland as shown below Body Sealing Insert Clamping with Washer with Claw Nut 2 Insert the clamping nut into the Ethernet cable 3 Insert the sealing insert with claw 9 ACT Connecting Vision vA Hardware Manual 4 Attach the cable gland body to the hole of the camera Attach to Camera Side Hole Attach to Camera Bottom Hole 5 If the cable will be routed along the surface skip this step If the cable will pass through the surface do the following a Pull the network cable through the bottom conduit hole b Insert the sealing insert with claw into the cable gland body and then attach the clamping nut to complete the cable solution NOTE Make sure the clamping nut is tightly attached to the cable gland body and the seali
5. Ceiling light or a motor that opens or closes a gate In this case there is a need to connect an external relay See wiring scheme below NORMAL HIGH TRIGGER LOW MOTOR Note that when choosing an appropriate relay please refer to its specifications and make sure they match the above design The triggering circuit voltage has to be around 12V DC and the switch controlled circuit voltage has to match the external power supply e g 110V AC or 220V AC The illustration below is a graphic example of connecting a relay to a high voltage DO device 110V 220V AC External Power Source Camera Illuminator NOTE For more information on DI DO connections please refer to the Knowledge Base article All about Digital Input and Digital Output downloadable from the link below htto www acti com kb detail asp KB_ID KB20091230001 2 Pp ACTI Connecting Vision Hardware Manual Connecting Audio In Out Devices Optional Depending on your surveillance needs you may connect audio input or output device such as an active microphone or speaker to your camera In this case you need to connect the audio input output device to the supplied audio terminal block h Ere connect audio output devices map the pins to one of the pin combinations below Device Instructions GND connect the wires of the audio output device to GND Audio Output see Pin 1 and AUDIO OUT P
6. Knob Tilt Adjustment Screw Tilt Adjustment Screw Rotation Adjustment Focus Adjustment Screw Lens Adjustment Procedures gt gt X 1 Loosen the tilt adjustment screws adjust the tilt and then tighten back the screws to fix 3 4 W the tilt position 2 Move the rotation adjustment to rotate the viewing orientation Loosen the pan adjustment screw and move the pan direction 4 Loosen the focus adjustment screw and move the lens left or right to adjust focus and then tighten back the screw to fix the lens position 29 Dd ACTi Connecting Vision Hardware Manual Accessing the Camera Connect the Equipment To be able to connect to the camera firmware from your PC both the camera and the PC have to be connected to each other via Ethernet cable At the same time the camera has to have its own power supply In case of PoE cameras you can use a PoE Injector or a PoE Switch between the camera and the PC The cameras that have the DC power connectors may be powered on by using a power adapter The Ethernet port LED or Power LED of the camera will indicate that the power supply for the camera works normally Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only
7. 55 00 a TCM5111 228 5 6 1 172 16 26 57 i z T TCD2100 228 5 6 1 172 16 26 61 TCM1231 228 5 6 1 RISINIKININIRIRI SIRS RE With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh button of the IP Utility you will be able to see the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time 34 DP ACTI Connecting Vision Hardware Manual Access the Camera Now that the camera and the PC both have their unique IP addresses and are under the same network segment you can use Microsoft Internet Explorer on the PC to access the camera NOTE Only Microsoft Internet Explorer is supported by the camera at the time of writing this documentation Please refer to our website www acti com for future upgrades Internet Explorer supports the following functionalities Functionality Internet Explorer L
8. ME Desktop Je Downloads Recent Places a Libraries pdr l KCM7911 12H X 00008 0 KCM7911 12H X 00466 KCM8211 131 X 00037 l KCM8211 131 X 00049 ul EE Computer hi Network Mi adiin A 108 items i When the left mouse is clicked on the camera model name the default browser of the PC is automatically launched and the IP address of the target camera is already filled in the address bar of the browser lf you work with our cameras regularly then there is even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time 3 ACT Connecting Vision p gt Hardware Manual The IP Utility can be downloaded for free from http www acti com IP_Utility When you launch IP Utility the list of connected cameras in the network will be shown See sample illustration below Fe ru E E HK u IP Address NetMask 172 16 26 58 255 255 255 0 v Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Account Password 123456 Total 52 mn IP Address MAC Address FW Version Model Serial No Multicast IP 172 16 26 159 00 0F 7C 07 BB B7 A1D 311 V5 10 02 AC M
9. SDHC Card Slot Reset Button www acti com D4 ACTi Connecting Vision Hardware Manual 1 Power Button Press the Power Button to reboot the camera 2 Ethernet Port The Ethernet Port connects to a network using a standard Ethernet cable 3 Micro SDHC Card Slot Insert a Micro SDHC card here for local recording on camera 4 Reset Button The Reset Button is used to restore the default factory settings of the camera Step 1 Disconnect the power supply Step 2 Press and continue to hold the Reset Button with a sharp object like a pen Step 3 Connect the power supply while keeping the Reset Button pressed Step 4 Wait for 45 seconds and then release the Reset Button 5 Digital Input Output This connector connects to digital input or output devices such as an alarm trigger panic button etc Digital Input DI and Digital Output DO devices are used in applications like motion detection event triggering alarm notifications etc See Connecting DI DO Devices Optional on page 23 for information 6 DC 12V Power Input In case the camera is connected to a non PoE Power over Ethernet switch use this connector to connect the camera to an external power adapter See Connecting a Power Adapter Optional on page 21 for more information 7 Audio Input Output This connector connects to audio input or output devices such as a microphone or speaker See Connecting Audio In Out Devices Optional o
10. and the camera to make sure they are in the same network segment When the camera is plugged into the network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera 32 ACT Connecting Vision vA Hardware Manual Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below BE All Control Panel Items Network and Sharing Center Control Panel Home View your basic network information and set up connections Organize Disable this network device Diagnos i See full m 5 i Change adapter settings A Jo be ee full map acai lacs CER Serie midi SISO_NP_PC1 Network Internet Network This computer ae Intel R 3 a Disable View your active networks Connect or disconnect Status Diagnose Jo Network Access type Internet Work network Connections g Local Area Connection GS Bridge Connections 8 Create Shortc Change your networking settings zn Set up a new connection or network Delete Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or fa Rename access point Pro
11. egapixel IP Camera KCM5311 11L E 00010 228 5 6 1 172 16 26 52 00 0F 7C 00 00 02 A1D 311 V5 11 12 AC Megapixel IP Camera kcuse11 11A x 0000s 228 5 6 1 172 16 26 167 00 0F 7C 08 E8 B3 A1D 311 V5 11 07 AC Megapixel IP Camera KCM5611 12G X 00480 228 5 6 1 172 16 26 59 00 0F 7C 07 45 7B A1D 311 V5 09 09 AC a _KCM7111 11H X 00206 228 5 6 1 172 16 26 71 00 0F 7C 06 13 CB A1D 311 V5 10 02 AC Megapixel IP Dome KCM7211 11A X 00025 228 5 6 1 172 16 26 12 00 0F 7C 08 88 C7 A1D 311 V5 10 02 AC Megapixel IP Dome KCM7311 12E X 00188 172 16 26 74 00 0F 7C 66 68 89 A1D 311 V5 10 02 AC Hemispheric Camera KCM7911 12H X 00008 228 5 6 1 172 16 26 124 00 0F 7C 09 16 57 A1D 311 V5 10 02 AC Hemispheric Camera KCM7911 12H X 00466 228 5 6 1 172 16 26 53 00 0F 7C 0B A6 D0 A1D 311 V5 10 02 AC Megapixel IP PTZ Camera KCM8211 131 X 00037 228 5 6 1 172 16 76 A9 O0 0F 7C 0R ABDC A1N 311 V5 10 13 AC Menanixe l IP PTZ Camera KCM amp 211 13LX NNN49 PPR 561 ceili _ pense 4 Megapixel IP Dome You can quickly notice the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera already filled in the address bar of the browser Use the default IP address of the camera If there is no DHCP server in the given network the user may have to manually assign the IP addresses to both the PC
12. es DO map the pins to one of the pin combinations below Device Pin oo Mapping Instructions Digital Output 1 Connect the wires of the first output device to 12V DO1 Pin 2 and DO1 Pin 4 Digital Output 2 6 lv Connect the wires of the second output device to 12V DO2 8 ooe Pin 6 and DO2 Pin 8 The table below shows the DI DO connection specifications Device Connection design TTL compatible logic levels To trigger low Logic level 0 OV 0 4V Voltage Normal ae Logic level 1 3 1V 30V Current 10mA 100mA Connection design Transistor Open Collector Voltage amp Current lt 24V DC lt 100mA Typical Connection Based on these specifications if the DI device has a voltage of OV 30V or the DO device has a voltage of lt 24V lt 100mA then the camera can supply internal power to these devices and there is no need to connect the DI DO device to an external power source In this case wire connection to Pins 1 to 4 Use the GND and DI1 pins to connect a DI device and use the 12V and DO1 pins to connect a DO device See wiring scheme below NORMAL 3 1V NORMAL HIGH TRIGGER LOW BATTERY I 24 Pp ACTI Connecting Vision Hardware Manual Consequently to connect a second DI or DO device wire the connection to Pins 5 to 8 High Voltage DO Device Connection Even though the camera provides 12V power this may not be enough for some high voltage DO devices such as a
13. evices to your camera to trigger events or notifications Digital Input DI devices can be used to notify the camera about an activity in the camera site DI can be triggers of events For example you can connect a panic button to the camera as such when the panic button is pressed the alarm signal will be sent through the camera Other common DI device applications are emergency button smoke detector passive infrared sensor etc Digital Output DO devices are external devices that are activated by the camera upon an event inside the camera For example you can connect an alarm horn to the camera as such when an event occurs inside the camera e g detected intruder the alarm horn will sound Other common DO device applications are motion triggered lights electric fence magnetic door locks etc You can connect up to two DI and two DO devices to your camera Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure the wire 12 3 4 5 6 7 8 To connect input devices DI map the pins to one of the pin combinations below Device Mapping Instructions Connect the wires of the first input device to GND Pin 1 and DI Pin 3 Digital Input 1 DI1 Connect the wires of the second input device to GND Pin 5 and DI2 Pin 7 Digital Input 2 DI2 www acti com Pp ACTI Connecting Vision Hardware Manual To connect output devic
14. f the camera and attach the cap to the side conduit hole to close it Route the network cable to pass this hole from the surface e Ifthe cables will be routed along the surface skip to the next step 0 ACTI Connecting Vision vA Hardware Manual Step 2 Open the Dome Cover 1 Remove the plastic covering the camera 2 Loosen the three 3 screws securing the dome cover 3 Carefully lift to open the dome cover and place it on the side of the camera NOTE Do not abruptly lift the dome cover it is attached to the camera with a spring wire 1 4 ACTI gt Connecting Vision Hardware Manual Step 3 Prepare for Waterproof Installation The camera comes with two 2 glands used for waterproof installation e Cable Gland For use with an Exterior grade Ethernet cable Exterior grade Ethernet cables are already waterproof See Waterproof Solution with Naked Cable on page 13 e Conduit Gland For use with a flexible conduit This solution is recommended when an exterior grade Ethernet cable is not available or when other input output devices or external power adapter will be connected to the camera See Waterproof Solution with Conduit on page 15 Determine the type of waterproof solution that is applicable to your installation requirements and prepare the necessary accessories or purchase extra materials Cable Gland Conduit Gland For use with a 3 8
15. ges to the product and manuals without prior notice FCC CE Regulation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the users will be required to correct the interference at their own expense 4 www acti com Bq ACTi Connecting Vision Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When t
16. he power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the video product 3 If the inner parts of video product have been directly exposed to rain or water If the video product does not operate normally by following the operating Instructions in this manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition 5 www acti com ACTI Connecting Vision vA Hardware Manual Introduction Package Contents Check if the camera package comes with the following items Camera Conduit Gland Cable Gland Hexagon Wrench Pan Bracket Wrench Mounting Screw Kit m Terminal Block Terminal Block Terminal Block for Power ic D 07 D10 for Audio In Out Quick Installation Guide Warranty Card Drill Template Drill Template www acti com pa ACT Hardware Manual Physical Description KCM 7111 KCM 7311 KCM 7211 Digital Input Output O DC 12V Power Input Audio Input Output Power Button Ethernet Port O Micro
17. holes on the surface and attach the three 3 supplied screws to secure the camera Step 5 Connect the Cable s 1 If the cables will be routed along the surface pull the network cable and the other cables if any through the side conduit hole and attach the sealing insert and the clamping nut to the gland body Using Flex Conduit Using Naked Cable 2 Connect the network cable to the Ethernet port and the other cables if any to their corresponding connectors on the camera Digital Input Output DI DO Connector 12V Power Connector Audio Input Output Connector Ethernet Port 9 ACT Connecting Vision da Hardware Manual Step 6 Access the Camera Live View See Accessing the Camera on page 30 for more information Step 7 Adjust the Viewing Angle and Focus Based on the live view adjust the viewing angle and orientation of the camera Adjustments vary per model for detailed information please refer to the following sections e For KCM 7111 camera models see KCM 7111 on page 29 e For KCM 7311 and KCM 7211 camera models see KCM 7311 KCM 7211 on page 27 Step 8 Close the Dome Cover 1 Align the position of the dome cover shroud to the direction of the lens 2 Tighten the three 3 screws to attach the dome cover to the camera body 20 D4 ACTi Connecting Vision Hardware Manual Other Connections This section describes the pr
18. in 2 a GND Connect the wires of the audio input device to GND Audio Input 4 pe Pin 3 and AUDIO IN Pin 4 Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure the wire NOTE For more information about AUDIO in connections please refer to the Knowledge Base article How to Use Audio in of ACTi Cameras downloadable from the link below http www acti com support KnowledgeBase outside detail asp KB ID KB20100114003 2 ACT Connecting Vision WW Hardware Manual d Other Adjustments How to Adjust Focus and Viewing Angle KCM 7311 KCM 7211 Camera Parts Overview p Pan Adjustment Knob y Tilt Adjustment Screw Tilt Adjustment Screw Rotation Adjustment Zoom Lens Adjustment Procedures m Ei 1 Loosen the tilt adjustment screws adjust the tilt and then tighten back the screws to fix the tilt position Move the rotation adjustment to rotate the viewing orientation Move the pan direction left or right 7 ACTI Connecting Vision vA Hardware Manual NOTE If you need to tighten or loosen the pan adjustment knob and adjustment by hand is not enough insert the bundled pan bracket wrench into the hole on the knob and then push it to the left or to the right 28 ACT Connecting Vision vA Hardware Manual KCM 7111 Camera Parts Overview Pan Adjustment
19. ive Video Live Video Area Resizable ee PTZ Control Capture the snapshot Video overlay based configuration Motion Detection regions Privacy Mask regions All the other configurations The ActiveX control for video stream management will be downloaded from the camera directly the user has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into the Web browser s address bar http 192 168 0 100 5 ACT Connecting Vision vA Hardware Manual Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience p Bad am 3E http 192 168 0 100 P 2 gt X S Web Configurator Web Configurator PA Aci Account Password Language English z Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 For further operations please refer to the Firmware User Manual 6
20. n page 26 for more information 8 www acti com ACTI Connecting Vision vA Hardware Manual Mounting Solutions There are several mounting options that you can use to install the camera Below are the most common options Mount Types Accessories Surface Use the mounting screw kit included in the Mount camera package no additional accessories are required See Installing the Camera on on page 10 for installation instructions PMAX 1003 L Type Wall PMAX 0308 Mount Pendant Mount KR F w Gooseneck PMAX 0101 PMAX 0303 PMAX 0503 Pole Mount For more information about mounting solutions and accessories please visit to our website htto www acti com mountingselector 9 www acti com WA lt gt ACT Connecting Vision Hardware Manual Installing the Camera on a Surface Step 1 Drill the Holes 1 Using the supplied drill template mark the screw holes location on the surface then drill the holes and insert the plastic plugs 2 Determine how the cables will be routed pass through the surface or along the surface e Ifthe cables will pass through the surface a Mark and drill the conduit hole location on the surface as shown on the drill template Mounting Hole ZES Mounting Hole Mounting Hole 9 A U Conduit Hole B507 00035 000 Drill template scale 1 1 b Remove the metal cap covering the bottom conduit hole o
21. ng insert is squeezed tightly 6 Proceed with Step 4 Install the Camera to the Surface on page 19 4 Pp ACTI Connecting Vision Hardware Manual Waterproof Solution with Conduit This section describes the procedures to waterproof the cabling connections using the bundled conduit gland and flexible conduit This is the recommended if other input output devices or an external power adapter will be connected to the camera or when an exterior grade Ethernet cable is not available 1 Prepare the following materials for waterproof installation Conduit Gland included in the camera package For use with 3 8 flexible conduit For use with 1 2 flexible conduit Flexible Conduit Network Cable 3 8 or 1 2 Trade size CAT 5 or CAT 6 not included in the package not included in the package NOTE The bundled conduit gland may vary Check the conduit gland that came with your package to determine if 3 8 or 1 2 is the suitable flexible conduit size 2 Disassemble the bundled conduit gland as shown below Lock Nut Sealing Insert Body Clamping Nut gt 0 s0 NOTE In this installation the conduit gland body can be securely attached to the camera therefore the use of lock nut is not necessary Please set the lock nut aside 9 ACT Connecting Vision vA Hardware Manual 3 Pull the network cable through the flex conduit If connecting other input output devices or an e
22. ocedures in preparing the external devices that you can connect to the camera The camera supports DC12V power input Digital Input and Output DI DO and Audio Input and Output devices using the bundled terminal blocks The use of these devices however is optional Connecting a Power Adapter Optional In case of using a non PoE switch or your PoE switch has limited power supply you can purchase a power adapter and directly connect the camera to a power outlet The power adapter must be connected to the supplied terminal block before use To do this follow the procedures below 1 Loosen the screws of the 12V and GND pins of the power terminal block 2 Take note that a standard power adapter cable has two 2 different wires Connects to GND Pin White stripe Connects to 12V Pin 2 ACTI Connecting Vision vA Hardware Manual 3 Connect the wire with the white stripe to the 12V pin and the other to the GND pin 4 Tighten the screws of the 12V pin and the GND pins to secure the wire connection 5 Set the prepared power adapter for connection later Below is an example of a power adapter with an attached terminal block NOTE The power adapter is not bundled in the package 2 ACT Connecting Vision vA Hardware Manual Connecting DI DO Devices Optional Depending on your surveillance needs you may connect digital input or output d
23. perties Connect to a network Een Connect or reconnect to a wireless wired dial up or VPN network connection HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing Windows Firewall Ca x Connect using EP Intel R 82567LM 3 Gigabit Network Connection You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items JN Client for Microsoft Networks E VirtualBox Bridged Networking Driver Sl QoS Packet Scheduler Sl File and Printer Sharing for Microsoft Networks Use the following IP address IP address Subnet mask 255 255 255 0 Default gateway 4 Intemet Protocol Version 6 TCP IPv intemet Protocol 4 TCP IPv4 Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder Install Uninstall Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server F Validate settings upon exit 33 www acti com
24. the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP server to assign IP addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from the DHCP server automatically In such case the camera will immediately be ready for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in order to access it using a Web browser 30 ACT Connecting Vision AP LA Hardware Manual The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our Cameras In the example below the camera that has just been connected to the network is successfully found Ge th gt Network gt v 4 Search File Edit View Tools Help Organize v Search Active Directory Network and Sharing Center Q KCM5111 11G X 00280 0 KCM5211 11K E 00410 Q KCM5611 11A X 00005 0 KCM7111 11H X 00206 Q KCM7211 11A X 00025 Wr Favorites
25. xternal power adapter pull the cables through the flex conduit without connectors The terminal blocks will be attached once the cables pass through the camera hole later 4 Insert the clamping nut through the flex conduit 5 Insert the sealing insert and attach it at the end of the flex conduit verteren oS m jo ACT Connecting Vision vA Hardware Manual 6 Screw the conduit gland body to the conduit hole of the camera Attach to Side Conduit Hole Attach to Bottom Conduit Hole 7 Ifthe cable will be routed along the surface skip this step If the cable will pass through the surface do the following a Pull the network cable and other cables if any through the bottom conduit hole b Insert the sealing insert into the conduit gland body and then attach the clamping nut to complete the cable solution 7 ACT Connecting Vision vA Hardware Manual 8 If connecting other cables attach the terminal blocks to the cables See Other Connections on page 21 9 Proceed with Step 4 Install the Camera to the Surface on page 19 s ACTI Connecting Vision vA Hardware Manual Step 4 Install the Camera to the Surface 1 If necessary insert a micro SHDC card up to 32 GB into the card slot of the camera 2 Align the camera screw holes and the conduit hole if necessary to the
Download Pdf Manuals
Related Search