JAM Pack Emerald User Manual Rev. 1
Contents
1. JAMTM Pack Emerald User Manual Rev 1 WORLD HEADQUARTERS Chauvet General Information CONTACT US Address 5200 NW 108th Avenue Sunrise FL 33351 Voice 954 577 4455 Fax 954 929 5560 Toll free 800 762 1084 Technical Support Voice 954 577 4455 Press 4 Fax 954 756 8015 Email tech chauvetlighting com World Wide Web www chauvetlighting com UNITED KINGDOM AND IRELAND Chauvet Europe Ltd General Information Address Unit 1C Brookhill Road Industrial Estate Pinxton Nottingham UK NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO Chauvet Mexico General Information Address Av Santa Ana 30 Parque Industrial Lerma Lerma Mexico C P 52000 Voice 52 728 285 5000 CHAUVET EUROPE Chauvet Europe BVBA General Information Address Stokstraat 18 9770 Kruishoutem Belgium Voice 32 9 388 93 97 Technical Support Email uktech chauvetlighting com World Wide Web www chauvetlighting co uk Technical Support Email servicio chauvet com mx World Wide Web www chauvet com mx Technical Support Email Eutech chauvetlighting eu World Wide Web www chauvetlighting eu Outside the U S United Kingdom Ireland Mexico or Benelux contact the dealer of record and follow their instructions to request support or to return a product Visit the Chauvet website for contact information JAMTM Pack Emerald User Manual Rev 1 Page 15 of 152. circuit breaker or fuse Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire To eliminate wear and improve its lifespan during periods of non use completely disconnect from power via breaker or by unplugging it Never connect the product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch 1 Disconnect the fogger from power 2 Wedge the tip of a flat head screwdriver into the slot of the fuse holder 3 Pry the safety cap out of the housing 4 Remove the blown fuse from the clip on the front of the safety cap and replace with a fuse of the exact same type and rating 5 Re insert the fuse holder and reconnect power The product does not ship with a spare fuse however the safety cap has room for a External AC Power Supply A O spare Always replace a blown fuse with a fuse of the same type and rating The JAM M Pack Emerald UV Strobe Combo has an external auto ranging power supply that can work with an input voltage range of 100 to 240 VAC 50 60 Hz To determine the product s power requirements circuit breaker power outlet and wiring use the current value listed on the label affixed to the power supply s back panel or refer to the product s specifications chart The listed current rating indicates the product s average current draw under normal conditions Always connect the prod
3. Chauvet Instead contact your local distributor See www chauvetlighting com for distributors outside the U S UK Ireland Mexico or Benelux If you are located outside the U S UK Ireland Mexico or Benelux contact your distributor of record and follow their instructions on how to return Chauvet products to them Visit our website www chauvetlighting com for contact details Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization RMA number before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return Send the merchandise prepaid in its original box and with its original packing and accessories Chauvet will not issue call tags Clearly label the package with the RMA number Chauvet will refuse any product returned without an RMA number Write the RMA number on a properly affixed label DO NOT write the RMA number directly on the box Before sending the product clearly write the following information on a piece of paper and place it inside the box Your name Your address Your phone number RMA number A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be your responsibility FedEx packing or double boxing are recommended Chauvet reserves the right to use its own discretion to repair or replace returned product s
4. Cord plug Power I O Power input connector Power Supply Unit Type LED Color White UV Parameter Strobe Rate Heat up Time 2 5 min Output 1 500 cfm Length 13 ft 4 m Maximum External Temp 104 F 40 C Product Name JAM Pack Emerald 120 V JAM Pack Emerald 230 V JAMTM Pack Emerald User Manual Rev 1 UV Strobe Combo 12 VDC 1A External Power Supply Switching 100 240 VAC 50 60 Hz Auto Ranging UV Strobe Combo 12 W 0 18 A 12 W 0 10 A N A U S Worldwide IEC Edison Edison U S U S Worldwide Power DC Input 12 VDC AC Adapter Power 0 6 W Quantity 4 5 UV Strobe Combo O to 16 Hz Tank Capacity 0 2 gal 0 6 Cooling System Convection Item Code 10051083 10051084 Weight 0 6 Ib 0 3 kg 4 Ib 1 8 kg Fog Machine Model specific 120 VAC 60 Hz or 230 VAC 50 Hz Fixed Fog Machine 471 W 3 9A 471 W 2 0A F5A 250 V Lifespan 50 000 hours Current 0 19A 0 31A Fluid Consumption 7 5 ml min UPC Number 781462214319 781462214326 RoHS CER Page 13 of 15 RETURNS Page 14 of 15 E In case you need to get support or return a product If you are located in the U S contact Chauvet World Headquarters If you are located in the UK or Ireland contact Chauvet Europe Ltd If you are located in Mexico contact Chauvet Mexico If you are located in Benelux contact Chauvet Europe BVBA If you are located in any other country DO NOT contact
5. correctly if this information is not used Useful information LEO gt Disclaimer The information and specifications contained in this document are subject to change without notice Chauvet assumes no responsibility or liability for any errors or omissions that may appear in this manual Chauvet reserves the right to update the existing document or to create a new document to correct any errors or omissions You can download the latest version of this document from www chauvetlighting com O Copyright 2015 Chauvet All rights reserved Electronically published by Chauvet in the United States of America Author Date Editor Updated R Isenstadt 07 01 15 A Leon 07 02 15 JAMTM Pack Emerald User Manual Rev 1 Page 3 of 15 Auto Programs pP Auto ranging Power Supply P X X Product ata Use on Dimmer Glance Outdoor Use Sound Active DMX Master Slave Replaceable Fuse User Serviceable Safety Notes Please read the following Safety Notes carefully before working with the product The Notes include important safety information about installation usage and maintenance Always connect the product to a grounded circuit to avoid the risk of electrocution Always disconnect the product from the power source before cleaning Avoid direct eye exposure to the light source while the product is on Make sure the power cord is not crimped or damaged Never disconnect the product from power cord by pulling or tugging on the cord If mo
6. OO EMERALLI User Manual any n ent D O OOOO 0600000000 00000VOVO TABLE OF CONTENTS 1 Belore VOU BOO IN Bee anne nee 3 WhnatisIlnclded ista aaa 3 Unpacking instructions ESA E A iee 3 SMN a A A td 3 TEX CONVENIO SEN A AO 3 SYD a N ee ee 3 DISAINER NNN 3 Producta aaa 4 Salely NS O N E E 4 2 IARtTFOdUCUIO Ni 5 PrOQUCEOVE VIEWS lt a a a a 5 UN SIG ODS COM DO ld added 5 o een esse es Nee 5 PIOQUEE DIMENSION Saar are 6 LP SVODE COMO oa 6 FOO Mac papada 6 Ds DOD A BE PERL OR ER DREIER AREESERSEDENERERTEES 7 FOR Machine AGF OWL tiara aid 7 Fog Machine Fuse Replacement cccccscccccsseecceeseeccececccsseecceseecsauseecegeeeseueeeesaueeesseeeesseeeeesaaeesseaes 7 External AC Power SUDON ze ee ee is 7 MOUNT a ie ee ee 8 A ee ee Eee ea Nee on ee en Misere 8 FALCO A an ee ne ee ee 8 RO 01 1 1 1 110 2 ironin A 9 FOG Machine Wired REMOS victor ee een leere 9 UV Strobe Control Pa el Operation ee 9 WV Strobe Combo o trobe Mode S vitalidad 9 orobe Mode ra aa ee Eee Eee Eee 9 UV ON O Ma taa 9 infrared Remote COM discordia io ed 10 O ne ee nee 10 5 MaiMtenaN CE Eee 11 Producir lala 11 FOO Machine MalmtenanNC Eur iia 11 A ee 11 6 General Fogger Troubleshooting u uu22u20002n00nnnn0nnnnunnnnnnnnnnnnnnnunnnnnnnnnnnnnnn 12 7 TECANICAlSPeciica ON Scans 13 Reli id 14 contact Usina 15 Page 2 of 15 JAMTM Pack Emerald User Manual Rev 1 1 BEFORE YOU BEGIN W
7. edly until the desired mode is set UV On Off The UV LEDs on the UV Strobe Combo are controlled separately from the white strobe LEDs If the UV LEDs are On press lt UV ON OFF gt to turn them Off If the UV LEDs are Off press lt UV ON OFF gt to turn them On JAMTM Pack Emerald User Manual Rev 1 Page 9 of 15 Infrared The JAM M Pack Emerald UV Strobe Combo is compatible with the IRC 6 infrared remote control from Chauvet IRC mode will activate at the press of any button on the Remote remote Control IRC 6 Operation Be sure the IRC 6 remote is pointing directly at the product and there is nothing in between the remote and the product The following buttons function with the JAM M Pack Emerald UV Strobe Combo lt BLACK OUT gt Turns LEDs on off lt SOUND gt Selects Sound Active mode lt STROBE gt Start Stop strobing lt UV gt Turns the UV on lt W gt Turns white on lt gt Increases Strobe speed lt gt Decreases Strobe speed All other buttons on the remote have no function with this product a Q 4 Q OJIOIOIOCISIONGIOJO VOGUE V o The IRC 6 will not respond to any inputs when Black Out is activated If the i remote does not respond when a button is pressed try pressing lt BLACK OUT gt You may have inadvertently activated Black Out Page 10 of 15 JAM Pack Emerald User Manual Rev 1 5 MAINTENANCE Product Dust build up reduces light output performance and can cause ov
8. erheating This can lead 7 to reduction of the light source s life and or mechanical wear To maintain optimum Maintenance performance and minimize wear clean your lighting products at least twice a month However be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency To clean the product follow the instructions below 1 Unplug the product from power 2 Wait until the product is at room temperature 3 Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surface vents 4 Clean all transparent surfaces with a mild soap solution ammonia free glass cleaner or isopropyl alcohol 5 Apply the solution directly to a soft lint free cotton cloth or a lens cleaning tissue Softly drag any dirt or grime to the outside of the transparent surface 7 Gently polish the transparent surfaces until they are free of haze and lint O i Always dry the transparent surfaces carefully after cleaning them Do not allow the fogger to become clogged After every 40 hours of continuous operation use CHAUVET Fog Cleaner Quart FCQ through the system to prevent the accumulation of particulate matter in the heating element The recommended cleaning procedure is as follows 1 Unplug the product from power Fog Machine 2 Empty all fog fluid from the machine Maintenance 3 Add cleaning solution to the tank 4 Connect the product to power and al
9. g Clamp gt such as the CLP 02 from Chauvet Mounting Bracket Safety Cable Mou nting Diag ram Rubber Feet x4 for Bracket Adjustment such as CH 05 from Chauvet Floor Mounting Knobs Mounting Clamps such as the CLP 02 from Chauvet Page 8 of 15 JAM Pack Emerald User Manual Rev 1 4 OPERATION Fog Machine Trigger the fogger using the included wired remote The LED indicator on the remote indicates when the fogger has reached the required operating temperature Press the Wired Remote button on the remote to momentarily output fog The length of the wired remote cable is 13 ft 4 m UV Strobe Button Function Control Panel CoE Cycles through strobe modes Operation uv onorrs Turns the UV blacklight on or off Indicator LED will blink when Strobe mode is on Indicator LED will be static on when in Sound Active mode UV Strobe Function LED Status Combo Off Static On Strobe Modes Strobe Modes Medium 5 10 Hz nn gt speed of Fast 10 20 Hz Very Fast 20 30 Hz Static On Static On Sound Active Mode Static On The products will only respond to low frequencies of music bass and drums Strobe Mode Pressing lt STROBE MODE gt changes the UV Strobe Combo to the next mode For example if the UV Strobe Combo is set to Static On mode and lt STROBE MODE gt is pressed once the mode will be set to Sound Active mode To cycle through modes on the UV Strobe Combo press lt STROBE MODE gt repeat
10. hat ls UV Strobe Combination Light External Power Supply Adapter Fog Machine Power Cord Included CHAUVET Fog Fluid FJP Warranty Card Permanently wired remote Quick Reference Guide IRC 6 Remote Control Unpacking Carefully unpack the product immediately and check the container to make sure all the i parts are in the package and are in good condition Instructions Claims f the box or the contents the product and included accessories appear damaged from shipping or show signs of mishandling notify the carrier immediately not Chauvet Failure to report damage to the carrier immediately may invalidate your claim In addition keep the box and contents for inspection For other issues such as missing components or parts damage not related to shipping or concealed damage file a claim with Chauvet within 7 days of delivery Text Convention Meaning Conventions 1 512 A range of values 50 60 A set of values of which only one can be chosen Settings A menu option not to be modified Menu gt Settings A sequence of menu options to be followed lt ENTER gt A key to be pressed on the product s control panel ON A value to be entered or selected Sym bols Symbol Meaning Critical installation configuration or operation information Not following these instructions may make the product not work cause damage to the product or cause harm to the operator Important installation or configuration information The product may not function
11. k before transporting the product To eliminate unnecessary wear and improve its lifespan during periods of non use completely disconnect the product from power via breaker or by unplugging it Keep this User Manual for future use If you sell the product to someone else be sure that they also receive this document FCQ Fog Cleaner Quart was specifically developed by Chauvet to clean your fog machine Make sure you use FCQ regularly no longer than 90 days between cleanings to increase the life of your product Page 4 of 15 JAM Pack Emerald User Manual Rev 1 2 INTRODUCTION Product Overviews Front Views Back Panel Views IR Sensor Sound Sensitivity Microphone UV Strobe Combo Control Panel Buttons Indicator LED DC Power In Fluid Line Fog Fluid Wired Remote Tank Cover Fog Machine Fuse Holder LJ Fog Fluid Level Fog Nozzle g Indicator JAM Pack Emerald User Manual Rev 1 Page 5 of 15 Product Dimensions UV Strobe Combo zen 40 mm Fog Machine Page 6 of 15 JAMTM Pack Emerald User Manual Rev 1 3 SETUP Fog Machine AC Power A O Fog Machine Fuse Replacement The JAMTM Pack Emerald fog machine has a fixed voltage power supply and it can work with an input voltage of 120 VAC at 60 Hz or 230 VAC at 50 Hz The listed current rating indicates the product s average current draw under normal conditions Always connect the product to a protected circuit
12. low it to warm up 5 Run the unit in a well ventilated area until the tank is almost empty Do not allow the pump to run dry 6 Refill with fogger fluid to continue using the fogger Run the machine briefly to clear any remaining cleaning solution from the pump and heater Do not operate the machine without fluid at any time FCQ Fog Cleaner Quart was specifically developed by Chauvet to clean your A Hurricane 700 Make sure you use FCQ regularly no longer than 90 days between cleanings to increase the life of your fogger Storage Before storing the fogger run FCQ through the system as described in the cleaning procedure above however only follow steps 1 through 5 Do not refill the tank with fog fluid if storing the fogger Cleaning the system prior to storage will help prevent any particles from condensing inside the pump or heater while not in use i Test run your fog machine on a monthly basis to achieve the best performance JAM Pack Emerald User Manual Rev 1 Page 11 of 15 6 GENERAL FOGGER TROUBLESHOOTING Symptom No output or fog machine is spitting fluid Circuit breaker or fuse keeps blowing Product does not power up Product stops pumping Loud noise Page 12 of 15 Possible Cause Incorrect fluid Blocked pipe or failing part Excessive load on the circuit Short circuit along the power lines No energy on power outlet Loose or damaged power cord Blown fuse Internal proble
13. m Low No Fluid Pump protection system engaged Possible Action Clean thoroughly with CHAUVET FCO For full instructions see Fog Machine Maintenance Refill with CHAUVET water based fog fluid Contact Customer Service Make sure that the total load does not exceed 80 of the breaker or fuse nominal current Check the power lines and power cords Check power outlet Change to another outlet Check the power cord Replace blown fuse with a good one of the same type and rating Send product for repair Refill product with fluid Release manual fog button and press it again to reset pump protection system If you still experience problems after trying the solutions presented here contact Chauvet Technical Support See Contact Us JAM M Pack Emerald User Manual Rev 1 7 TECHNICAL SPECIFICATIONS Dimensions and Weight UV Strobe Combo Fog Machine Power Fog Machine UV Strobe Combo Light Source Photometrics Fog Machine Operation Capacity Consumption Misc Wired Remote Thermal Ordering Length 21 2 in 537 mm 8 5 in 215 mm 1 6 in 40 mm 7 1 in 180 mm Height 2 2 in 55 mm 4 9 in 124 mm Note Dimensions in inches rounded to the nearest decimal digit Value Input Voltage Range Voltage Selection Parameter Consumption 120 V Operating Current 120 V Consumption 230 V Operating Current 230 V Fuse Power I O Power input connector Power output connector Power
14. uct to a protected circuit circuit breaker or fuse To eliminate wear and improve its lifespan during periods of non use completely disconnect from power via breaker or by unplugging it Never connect the product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch JAM Pack Emerald User Manual Rev 1 Page 7 of 15 Mounting Before mounting the product read and follow the safety recommendations indicated in the Safety Notes Orientation The Products in the JAMTM Pack Emerald may be mounted in any position however make sure adequate ventilation is provided around the product Rigging Before deciding on a location for the product always make sure there is easy access to the product for maintenance and programming purposes Make sure that the structure onto which you are mounting the product can support the product s weight See the Technical Specifications for weight information When mounting the product overhead always use a safety cable Mount the product securely to a rigging point whether an elevated platform or a truss When rigging the product onto a truss use a mounting clamp of appropriate weight capacity The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired angle Only loosen or tighten the bracket knobs manually Using tools could damage the knobs Safety Cable such as CH 05 from Chauvet Mountin
15. unting the product overhead always secure to a fastening device using a safety cable Make sure there are no flammable materials close to the product when operating Do not touch the product s housing when operating because it may be very hot The product is not intended for permanent installation Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product The product is for indoor use only IP20 To prevent risk of fire or shock do not expose the product to rain or moisture Always install the product in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces Be sure that no ventilation slots on the product s housing are blocked Never connect the product to a dimmer or rheostat Make sure to replace the fuse with another of the same type and rating Never carry the product from the power cord or any moving part Always use the hanging mounting bracket The maximum ambient temperature Ta is 104 F 40 C Do not operate the product at higher temperatures In the event of a serious operating problem stop using the product immediately Never try to repair the product Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Do not use for space heating purposes Use only CHAUVET water based fog fluid Drain the tan
Download Pdf Manuals
Related Search