Hedge Trimmer
Contents
1. Tr i k ta 009277 o DOUBLE INSULATION ENGLISH Original instructions SPECIFICATIONS Model UH4570 UH5570 UH6570 Blade length 450 mm 550 mm 650 mm Strokes per minute min 1 600 1 600 1 600 Overall length 862 mm 970 mm 1 042 mm Net weight 3 6 kg 3 7 kg 3 8 kg Safety class o4 II Due to our continuing program of research and development the specifications herein are subject to change without notice Specifications may differ from country to country Weight according to EPTA Procedure 01 2003 END220 5 Symbol The following show the symbols used for the equipment Be sure that you understand their meaning before use OT lt Read instruction manual DOUBLE INSULATION Do not expose to rain Remove plug from the mains immediately if the cable is damaged or cut Only for EU countries Do not dispose of electric equipment together with household waste material In observance of European Directive 2012 19 EU on waste electric and electronic equipment and its implementation in accordance with national law electric equipment that have reached the end of their life must be collected separately and returned to x E an environmentally compatible recycling facility ENE014 1 Intended use The tool is intended for trimming hedges ENF002 2 Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate2. 2 Branch catcher At this time the chip receiver needs to be installed so that its hooks fit into grooves in the shear blade unit 1 Hooks 2 Fit the hooks into groove 3 Grooves To remove the chip receiver press its lever on both sides so that the hooks are unlocked 1 Press the levers on both sides 2 Unlock the hooks A CAUTION The blade cover standard equipment cannot be installed on the tool with the chip receiver being installed Before carrying or storing uninstall the chip receiver and then install the blade cover to avoid blade exposure NOTE Check the chip receiver for secure installment before use Never try to uninstall the chip receiver by an excessive force with its hooks locked in the blade unit grooves Using the excessive force may damage it MAINTENANCE A CAUTION Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance Cleaning the tool Clean out the tool by wiping off dust with a dry or soap dipped rag A CAUTION Never use gasoline benzine thinner alcohol or the like Discoloration deformation or cracks may result Blade maintenance Smear the blade before and once per hour during operation using machine oil or similars After operation remove dust from both sides of the blade with wired brush wipe off it with a rag and then apply enough low viscosity oil such as machine oil etc and spray type lubric
3. Hook complete 2 Tool s cord 3 Extension cord When engaging the extension cord secure it to the tool s cord with the hook complete Attach the hook about 100 200 mm from the extension cord connector This will help prevent unintentional disconnection Waist cord hook CAUTION Do not attach the holder of waist cord hook to other than the extension cord Do not attach it in a position closer to the tool beyond the hook complete Failure to do so may cause an accident or personal injury Attach firmly one hook of the hook complete to the tool s cord and the other hook of hook complete to the extension cord Working with the tool with a sole hook only attached may cause an accident and injury Using the waist cord hook helps to minimizing a risk of cutting off the extension cord unexpectedly caused by the loose extension cord Hook Tool Tool s cord Hook complete Extension cord Holder Waist cord hook NO O1 B N Press in or pull out the cord through the opening of the holder 1 Holder 1 2 Cord ZN 2 A CAUTION Do not force the opening of the holder Failure to do so may cause deflection and damage to it Arm cord hook Accessory A CAUTION Do not attach the holder of arm cord hook to other than the extension cord Do not attach it in a position closer to the tool beyond the hook complete hooks Failure to do so may cause an accident or personal injury Attach firmly o
4. and can only be operated on single phase AC supply They are double insulated and can therefore also be used from sockets without earth wire ENG905 1 Noise The typical A weighted noise level determined according to EN60745 Sound pressure level Lpa 89 9 dB A Sound power level Lwa 97 9 dB A Uncertainty K 1 5 dB A Wear ear protection ENG900 1 Vibration The vibration total value tri axial vector sum determined according to EN60745 Work mode hedge trimming Vibration emission an 6 7 m s Uncertainty K 1 5 m s ENG901 1 The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another The declared vibration emission value may also be used in a preliminary assessment of exposure ZAWARNING The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time ENH021 7 For European countries only EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine s Designation o
5. have an experienced hedge trimmer user show them how to use the trimmer The hedge trimmer must not be used by children or young persons under 18 years of age Young persons over 16 years of age may be exempted from this restriction if they are undergoing training under the supervision of an expert Use the hedge trimmer only if you are in good physical condition If you are tired your attention will be reduced Be especially careful at the end of a working day Perform all work calmly and carefully The user is responsible for all damages to third parties Never use the trimmer when under the influence of alcohol drugs or medication Check to make sure that the voltage and frequency of the power supply correspond to the specifications given on the identification plate We recommend the use of a residual current operated circuit breaker ground fault circuit interrupter with a tripping current of 30 mA or less or an earth leakage current protector 11 Work gloves of stout leather are part of the basic equipment of the hedge trimmer and must always be worn when working with it Also wear sturdy shoes with anti skid soles 12 Before starting work check to make sure that the trimmer is in good and safe working order Ensure guards are fitted properly Check cable for damage before starting work and replace if necessary The hedge trimmer must not be used unless fully assembled 13 Keep cable away from the cutting area Always wor
6. maintenance or adjustment should be performed by Makita Authorized Service Centers always using Makita replacement parts OPTIONAL ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita Service Center Blade cover Hook complete Shear blade assembly Waist cord hook Arm cord hook NOTE Some items in the list may be included in the tool package as standard accessories They may differ from country to country 11 Makita Corporation Anjo Aichi Japan 884840F228 www makita com
7. ating oil A CAUTION Do not wash the blades in water Failure to do so may cause rust or damage on the tool Removing or installing shear blade A CAUTION Before removing or installing shear blade always be sure that the tool is switched off and unplugged When replacing the shear blade always wear gloves without removing blade cover so that hands and face does not directly contact the blade Failure to do so may cause personal injury NOTE Do not wipe off grease from the gear and crank Failure to do so may cause damage to the tool For specific way of removing and installing shear blades refer to the reverse of a package for accessory shear blades Removing the shear blades Reverse the tool and loosen four screws 1 Screws 2 Blade cover NOTE Be careful not to get your hands dirty as grease is applied in the shear blade driving area Remove the under cover 1 Under cover 2 Blade cover 1 Gear housing cover Set the crank at the angle as shown in the figure with a slotted bit screwdriver 1 Crank Remove two screws from the shear blades and the shear blade unit will be taken out 1 Screws 2 Shear blade A CAUTION Return the gear to the original position in such a manner as it was installed if it should be taken away by mistake Installing the shear blade Prepare 4 removed screws For under cover 2 screws For shear blade gear housing cover under cover and new shear b
8. f Machine Hedge Trimmer Model No Type UH4570 UH5570 UH6570 Specifications see SPECIFICATIONS table are of series production and Conforms to the following European Directives 2000 14 EC 2006 42 EC And are manufactured in accordance with the following standards or standardised documents EN60745 The technical documentation is kept by Makita International Europe Ltd Technical Department Michigan Drive Tongwell Milton Keynes Bucks MK15 8JD England The conformity assessment procedure required by Directive 2000 14 EC was in Accordance with annex V Measured Sound Power Level 98dB A Guaranteed Sound Power Level 100dB A 30 1 2009 He Tomoyasu Kato Director Makita Corporation 3 11 8 Sumiyoshi cho Anjo Aichi 446 8502 JAPAN GEA005 3 General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool Work area safety 1 Keep work area clean and well lit Cluttered or dark areas invite accidents 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes 3 Keep c
9. force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of Starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar With the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tools operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a haza
10. hildren and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety 4 Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock 5 Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded 6 Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock 7 Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock 8 When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock 9 If operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 10 Use of power supply via a RCD with a rated residual current of 30mA or less is always recommended Personal safety 11 Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are t
11. ired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury 12 Use personal protective equipment Always wear eye protection Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries 13 Prevent unintentional starting Ensure the switch is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents 14 15 16 A7 Remove any adjusting key or wrench before turning the power tool on wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards Power tool use and care 18 19 20 21 22 23 24 Do not
12. k in such a way that the extension power cord is behind you 14 Remove plug from the mains immediately if cable is damaged or cut 15 Make sure you have a secure footing before starting operation 16 Hold the tool firmly when using the tool 17 Do not operate the tool at no load unnecessarily 18 Immediately switch off the motor and unplug the mains plug if the cutter should come into contact with a fence or other hard object Check the cutter for damage and if damaged repair immediately 19 Before checking the cutter taking care of faults or removing material caught in the cutter always switch off the trimmer and unplug the mains plug 20 Switch off the trimmer and disconnect and secure the mains plug before doing any maintenance work 21 When moving the hedge trimmer to another location including during work always unplug the mains plug and put the blade cover on the cutter blades Never carry or transport the trimmer with the cutter running Never grasp the cutter with your hands 22 Clean the hedge trimmer and especially the cutter after use and before putting the trimmer into storage for extended periods Lightly oil the cutter and put on the cover The cover supplied with the unit can be hung on the wall providing a safe and practical way to store the hedge trimmer 23 Store the hedge trimmer with the cover on in a dry room Keep it out of reach of children Never store the trimmer outdoors 24 Do not ope
13. lades Adjust the crank position as shown in the figure At this time apply some grease provided with new shear blades to the periphery of the crank 1 Crank Overlap the oval hole in the upper blade with that in the lower one 1 Ellipse of shear blade Take out the blade cover from the old shear blades and fit it onto the new ones for easy handling during the replacement of blades Place the new shear blades on the tool so that the oval holes in the shear blades fit onto the crank Overlap the holes in the shear blades with the screw holes in the tool and then secure them with two screws 1 Ellipse of shear blade 2 Crank Check the crank for smooth turn with a slotted bit screwdriver 1 Crank Install the gear housing under cover on the tool Tighten the screw firmly Remove the blade cover and then turn on the tool to check it for proper movement NOTE When the shear blades does not operate properly there is a poor fit between the blades and crank Redo from the beginning Storage The hook hole in the bottom of the blade cover is convenient for hanging the tool from a nail or screw on the wall Put the blade cover on the shear blades so that the blades are not exposed Store the tool out of the reach of children carefully Store the tool in the place not exposed to water and rain To maintain product SAFETY and RELIABILITY repairs carbon brush inspection and replacement any other
14. ne hook of the hook complete to the tool s cord and the other hook of hook complete to the extension cord Working with the tool with a sole hook only attached may cause an accident and injury Using the arm cord hook helps to minimize a risk of cutting off the extension cord unexpectedly caused by the loose extension cord 1 Holder 2 Arm cord hook Attach firmly the arm cord hook placing around your arm and pass the extension cord through the holder The length of the arm cord hook band is adjustable NOTE Do not pass the extension cord through the band Do not force the opening of the holder Failure to do so may cause deflection and damage to it Using the arm cord hook together with the waist cord hook is more helpful OPERATION A CAUTION Be careful not to accidentally contact a metal fence or other hard objects while trimming The blade will break and may cause serious injury Overreaching with a hedge trimmer particularly from a ladder is extremely dangerous Do not work from anything wobbly or infirm Do not attempt to cut branches thicker than 10 mm diameter with this trimmer These should first be cut with shears down to the hedge trimming level CAUTION Do not cut off dead trees or similar hard objects Failure to do so may damage the tool Hold the trimmer with both hands pull the switch trigger A or B and move it in front of your body As a basic operation tilt the blades towards the
15. rate the tool at unnecessarily SAVE THESE INSTRUCTIONS no load ZA WARNING DO NOT let comfort or familiarity with product gained from repeated use replace strict adherence to safety rules for the subject product MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury FUNCTIONAL DESCRIPTION CAUTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool Switch action 1 Switch trigger B 2 Switch trigger A 3 Switch trigger C For your safety this tool is equipped with a triple switching system To turn on the tool press two out of three triggers A B and C Release either one of the two pressed triggers to turn off The sequence of switching is unimportant as the tool only starts when both switches are activated Straight cut To trim the hedge straight pull triggers A and B Vertical cut SES PT PTE ET OORT aT ARE A z ate WT eg et ret bei X Cut upwards with both hands pull the switch triggers B and C and move it in front of your body Far area cut To trim the hedge in far area with both hands pull the switch triggers A and C ASSEMBLY CAUTION Always be sure that the tool is switched off and unplugged before carrying out any work on the tool Engage the extension cord CAUTION Make sure that the extension cord is unplugged to the mains outlet 1
16. rdous situation Service 25 Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the 26 27 safety of the power tool is maintained Follow instruction for lubricating changing accessories Keep handles dry clean and free from oil and grease and GEB041 9 HEDGE TRIMMER SAFETY WARNINGS 1 Keep all parts of the body away from the cutter blade Do not remove cut material or hold material to be cut when blades are moving Make sure the switch is off when clearing jammed material A moment of inattention while operating the hedge trimmer may result in serious personal injury Carry the hedge trimmer by the handle with the cutter blade stopped When transporting or storing the hedge trimmer always fit the cutting device cover Proper handling of the hedge trimmer will reduce possible personal injury from the cutter blades Hold the power tool by insulated gripping surfaces only because the cutter blade may contact hidden wiring or its own cord Cutter blades contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Keep cable away from cutting area During operation the cable may be hidden in shrubs and can be accidentally cut by the blade Do not use the hedge trimmer in the rain or in wet or very damp conditions The electric motor is not waterproof First time users should
17. trimming direction and move it calmly and slowly at the speed rate of 3 4 seconds per meter 1 Trimming direction 2 Tilt the blades 3 Hedge surface to be trimmed To cut a hedge top evenly it helps to tie a string at the desired hedge height and to trim along it using it as a reference line Attaching the chip receiver accessory on the tool when trimming the hedge straight can avoid cut off leaves being thrown away To cut a hedge side evenly it helps to cut from the bottom upwards Trim boxwood or rhododendron from the base toward the top for a nice appearance and good job Installing or removing chip receiver accessory CAUTION Always be sure that the tool is switched off and unplugged before installing or removing chip receiver NOTE When replacing the chip receiver always wear gloves so that hands and face does not directly contact the blade Failure to do so may cause personal injury Always be sure to remove the blade cover before installing the chip receiver The chip receiver receives cut off leaves and alleviates collecting thrown away leaves This can be installed on either side of the tool 1 Press 2 Chip receiver 3 Nut 4 Shear blade Press the chip receiver on the shear blades so that its slits overlap with the nuts on the shear blades At this time make sure that the chip receiver does not contact branch catcher at the top of the shear blades 1 Nut
Download Pdf Manuals
Related Search