Galaxy Series Double-sided Rigid LED Light Manual Z2436CA
Contents
1. 2 Product Parts and Tools Required 1 Product Parts 2 Tools Required DIS Self tapping Screws ST2 9 Electrical Drill amp Drilling Bit Galaxy Series Products Bracket T wire Installation and Application Layout Guidelines Depth of Light Layout Spacing Installing Quantity Illuminance Range Box mm in mm in pcs of Z2436CA lux azaoa a amass 6 O o0600 Notes 1 The above data are tested with Z2436CA rigid LED light 2 Tested in 3mm 0 12in depth acrylic board with 54 4 luminous transmittance 3 Light box size 6 00mm 1000mm 23 6in 39 4in 4 The brightness of SAMSUNG LED is about 30 higher than Rishang LED 5 The layout of Z2472CA light can refer to that of Z2436CA light 6 The above data are for reference only Installation Procedures with Brackets After cleaning the installing surface determine the installing position and quantity Fix the brackets on the framework of light box and adjust the bracket spacing according to the depth of light box After fixing the brackets put the lights into the brackets and fasten them respectively Connect the T wire to the wires of rigid LED lights and secure the T wire well with screws Connect the rigid LED lights male socket to female socket and fix them Install the power supply and drill a hole near the end of T wire then treat the wire through hole to protect the wire from2. Install the power supply and The maximum load power per T wire is 180W forbid drill a hole near the end of T wire then treat the wire through hole to protect the wire from chasing Malfunction amp Solutions Table overloading If more products are needed the additional T wire Malfunction amp Solutions Table must be connected to a separate power supply If any T wire is 2 Short circuit occurs at the input of None LED power supply No primary power for the light works power supply The power supply is auto Remove any short or open protected since the short or open circuit circuits and other occurs at the output of the power supply Malfunctions and energize the fixture left unused please cut the unused part and protect the cut end against short circuit Declaration Warranty 3 years or 13 000 hours whichever comes first f the external flexible cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard All the data and pictures in this manual are subject to actual products Information provided is subject to change without notice Connect T wire to the power supply output correctly and cap both ends of T wire for good protection 3 The input wires of the rigid LED lights are connected reversely Galaxy Series Double sided Rigid LED Light Manual 1 No primary power for some
3. switch power supplies Check the power supply and Some LED 2 Some rigid LED lights are wrongly remove malfunctions lights don t connected to the power supply work 3 Some rigid LED lights polarities are Connect the wirescorrecti connected reversely y 4 Some T wires are connected wrongly Connect the T wires correctly Use higher or more power supplies ifthe rigid LED light is not long enough please connect the ends of rigid LED lights together A Note The maximum connectable quantity needs to meet the requirement shown in the table below the connection illustration forbid exceeding NONIE 1 Installation Notes 1 Clean the installing surface before installing the products 2 Make sure the polarity of connections made at the rigid LED light and power supply is correct otherwise the product will not be illuminated 3 Connect the rigid LED light to power supply firmly it will be fine until the wires cannot be pulled out by hand 4 The maximum quantity in parallel connection for Z2472CA is 6pcs 2 Notes for Optional Supplies 1 Forbid using any acid or alkaline adhesive to secure the product 2 The maximum connectable quantity is shown in the table below the connection illustration Please choose the safety certificated switch power supply with DC 12V output voltage with short circuit overvoltage and overcurrent protections the tolerance range for output voltage of the switch power supp
4. chasing Connect T wire to the power supply output correctly and cap both ends of T wire for good protection a a Pa 9 Bye E 1 4 il y 1 1 EN ifthe rigid LED light is not long enough please connect the ends of rigid LED lights together A Note The maximum connectable quantity needs to meet the requirement shown in the table below the connection illustration forbid exceeding Installation Procedures with End caps After cleaning the installing surface determine the installing position and quantity Put the rigid LED lights into the corresponding positions and secure the end caps at both ends with screws Connect the T wire to the wires of rigid LED lights and secure the T wire well with screws Connect the rigid LED lights male socket to female socket and fix them
5. ly is 5 If more products are needed ensure the power supply has more than 20 load allowance Z2436CA Z22472CA 1 The power supply is over loaded Make sure the working voltage of Brightness rigid LED light is within 95 105 of of the LED 2 The wire loss of the power supply is the rated voltage shorten the supply is dim or too much wire between the power supply and not even the first rigid LED light or use thicker supply wires Adjust the length of LED lights for each branch to meet the maximum connectable length 3 Too many rigid LED Lights are connected Find the intermittent LEDs are 1 Intermittent connections exist connections and remove blinking any malfunctions 2 Switch power supply doesn t work Replace the power supply AN WARNING This product is non waterproof only used indoors Forbid exposing it to outdoor or semi outdoor environment directly Do not disassemble or modify this product Turn power off before installing and serving the products Have a licensed electrician install maintain and serve the products The space between two rigid LED lights is no less than 50mm 2 0in otherwise the over temperature in light box will reduce the expected lifetime of rigid LED light Forbid using acid or alkaline adhesive to secure the product When use the neutral glass glue to fix the products do not seal the products until the glue solidified in open environment The sup
6. ply wire between the power supply and the rigid LED CE Gay Read this manual carefully before using this product and keep it light is no longer than 2m 78 7in otherwise the line loss will increase which will cause the brightness difference between the two ends Check the supply voltage and wire connections before power on V1 0 Model and Specification Galaxy Series Z2436CA Z2472CA Rates Power Working Voltage V DC12 25 60 13 140 25 70 13 158 Operating Temperature C F Storage Temperature C F Profile Drawings Unit mm in EEJ 5 0 197 3 8 0 15 1310 8 A o 1 2108 27 610 24 02 21018 27 34 81 37 628124 72 Fig 1 Z2436CA 5 0 197 3 810 15 LOS HA ji 210 8 27 f 1192 46 93 e1082 34 811 37 1210147 64 Fig 2 Z2472CA Product Parts and Tools Required 1 Connection Illustration aL Appearance Only for reference White wire Cathode Grey wire Anode Pe Grey wire Anode 4 White wire Cathode aL Power Appearance Only for reference Appendix Z2436CA Z2472CA The maximum load power per T wire is 180W forbid overloading If more products are needed the additional T wire must be connected to a separate power supply If any T wire is left unused please cut the unused parts and protect the cut end against short circuit
Download Pdf Manuals
Related Search