HD S Bullet Camera
Contents
1. HD S Bullet Camera User Manual Thank you for purchasing our HDS bullet camera Please read this manual carefully for correct use of the product and keep it for reference purposes X Warnings and Cautions W Disclaimer This manual may contain several technically incorrect places or printing errors The updates will be added into the new version of this manual The content is subject to change without notice W Avoid Electric Shock To prevent electric shock do not remove screws or cover W Avoid excessive moisture Do not use strong or abrasive detergents when cleaning camera body Clean with dry cloth or mild detergent wiping gently E Do not use camera beyond prescribed voltage range Only use included power supply Ensure power input source conforms to local voltage Voltage outside of range could cause damage or abnormal performance W Termly Inspection A few parts of the device shall be replaced regularly due to their average enduring time X Components and Accessories Camera User manual Screwdriver o 2 Screws Drill Template KX Overview This series of the camera supports varifocal lens and prime lens amp XTS CORP Headquarters Product Development Dpt A www xtscorp comBzrres W Never attempt to disassemble the camera privately It may result in internal components damaged Do not place the ca2. Ratio gt 52 dB AGC OFF Electronic Shutter 1 50s 1 67500s AGC Yes White Balance Auto White Balance Power DCIZY 10 Temperature 40 C 70 C Humidity 10 90 Dimension mm 109 x 284 x VN XTS CORP Headquarters Product Development Dpt py www xtscorp com
3. merain extreme hot orcold environment Use only under temperature conditions between 40 C and 70 C Provide good ventilation when using in high temperature conditions Do not aim camera at sun or extra bright place x ona fx Strong light will degrade image quality and could cause damage Do not drop the camera or subject it to physical shock It may cause production malfunction Avoid touching the camera lens The lens is the most important component of the camera Be careful not to smear it with fingerprints Lens Cover Video Cable Sun Shield Power Cable Bracket Zoom Mounting Base Focus X Connecting to Monitor X Connecting to Power HDS DVR HD Monitor Connect the adapter to the power input connector in accordance with the camera The recommended adapter specification for the camera is DC12V Power amp XTS CORP Headquarters SS Product Development Dpt www xtscorp com X Installation This series of product supports prime lens and varifocal lens If your camera is prime lens please skip the step of focus and zoom adjustment Before you start please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera 1 Attach the drill template to the place where you want to fix the camera and then drill 4 screw holes and 1 cable hole if you want to route the cables through the moun
4. nt mounting requirement by flexibly adjusting the lens into the required angle DNR Reduce noise from brighteness and color signal to save storage room under low illumination condition X Installation Fixed Screws 2 fe Tilt 90 C360 Rotate 5 Focus and zoom adjustment If the model you get is prime lens please skip this step Remove the lens cover and then adjust the focus and zoom screws to get aclear image Finally tighten these two screws and the lens cover Lens Cover 6 Remove the protection film softly to complete the installation This installation should be made by a qualified service person and should confirm to all local codes X Correct Disposal of This Product Ifthe camera no longer functions or can no longer be repaired it must be disposed ofaccording to regulations reading electronic waste By not disposing of electronic items in household waste you will not only be following the law but contributing the protection of the environment X Specifications Model BU1080PVF HDS Image Sensor 1 3 CMOS Pixels 1920 x 1080 Signal System PAL NTSC Min Illumination 0 Lux LEDON Lens 2 8 12 mm optional IR Visible Distance 30 50m IP Rank IP 66 Video Out BNCx 1 Resolution 1080 P 1920 x 1080 Frame Rate 30 fps 60Hz 25 fps 50Hz ICR Yes DNR Yes S N
5. ting base according to the drill template 2 Route the cables and connect the power cable and video cable 3 Secure the mounting base with camera to the ceiling or wall with screws as shown below Ceiling 4 Bracket adjustment Before adjustment preview the image of the camera on a monitor and then loosen the fixed screws to adjust the panning and tilting position ofthe camera After you adjusted tighten the fixed screws X Features This series of cameras adopt the latest HDS technology and advanced circuit design feature high definition and sensitivity low noise and distortion and support HD video transmission with the common coaxial cable ensuring the requirement of the HD monitoring in the traditional surveillance system High Resolution Adopt high performance HDSI sensor providing high definition and clear image up to 720P 1080P resolution High Transmission Performance Real time transmission with high speed and long distance ICR Auto Switch The filter will filter infrared light during the daytime and change to normal at night to ensure a high sensitivity and clear image Color B W Auto Switch The camera will display color image in daytime and become monochrome automatically at night Auto White Balance Adjust the color temperature according to the environment automatically 3 axis Adjustment Adopt advanced 3 axis mechanism design to meet differe
Download Pdf Manuals
Related Search