Installation Guide
Contents
1. 0 1 x Dryer el B 1 x Mounting plate Power cord a entry 1 x 2 5 mm Allen key 6 x Screws 12 x 30mm 6 x Expansion plugs Drain tank Air filter 189 79 5 103 5 Page 4 Precautions before installing E Do not install in the following types of location otherwise this may cause malfunction e Locations where the temperature can exceed 1 OC or 40 C e Locations where the dryer may come into direct contact with water e Locations where the dryer is under direct or strong sunlight e Locations where there is a lot of condensation e Locations where corrosive neutral or reductive gases are present e Places lower than 20m or higher than 2000m above sea level E Installation location Install somewhere the dryer will be easy to access Do not install the dryer too low The bottom of the dryer must be at least 150 mm higher than the floor The either side of the dryer must be at least 200 mm away from any walls Avoid locations where people or doors might bump into the dryer Choose a completely flat surface on the wall to install the dryer Hooks Expansion plug Position of lower holes Fixing screw Fixing screws Page 5 Installation Fixed wiring installation should be carried out by a qualified person Power requirements are 220 240 Volt AC 50 Hz 1 4kW Connect fixed wiring to the terminals marked Land N and ground This dryer is a Class appliance and requires an electrical earth g2. Ardrich HAND DRYERS User Manual N DUALDRI MODEL A266DD W or S AUTOMATIC DUAL JET HAND DRYER Page 2 AN WARNING personal injury accidents will happen if use improperly Prohibited Q Do not use In wet places a Wg INK b wa Do not allow the dryer to get wet Do not disassemble Please comply with instructions WARNING Do not open the front panel otherwise you may get an electric shock Children should not play on the machine Do not use in a wet environment which is subject to sprayed water and the places where the condensation may form This may cause electric shock and dryer malfunction Do not allow the unit get wet you may get an electric shock Do not modify and disassemble the dryer unnecessarily This may cause a fire electric shock or personal injury Rated power is required If power tolerance is over 10 there may be breakdown If using incorrect power supply fire electric shock and machine malfunction may happen Please use dedicated power outlet If using together with other appliances the outlet may cause abnormal heat leading to fire Power must be cut off when maintenance to prevent the risk of electric shock Drain tank and air filter must be installed If the machine doesn t work or has been subjected to abnormal conditions cut off the power to prevent accidents Ask supplier to check and repair The dryer must have a reliable gr
3. er holes Fixing screw Fixing screws Page 6 Installation and Testing 5 Fixed wiring Wire the terminal box 6 Re attach the terminal box cover Make sure the wires are not pinched Terminal box screw ay Wiring access T Re attach the front panel Put the cover into position and fit the two screws Attach the drain tank Front panel Make sure the air filter is all the way in Terminal box screw Drain tank Page 7 Using the dryer gm Turn on the power switch The power indicator lights up The blue lamp lights up in the drying cavity m Using the Unit Stretch out both hands and move them slowly into the dryer The dryer will start automatically Pull them out slowly letting the air blow the water off Pull them out completely Repeat if required Check Light Indicator When a malfunction or error occurs the check light will either light up or flash lower left front panel right side Turn off the power switch wait about 40 seconds until all the indicators go off then turn on the power switch If the indicator still lights up or flashes turn off the power disconnect the dryer from the power and contact your dealer If the check light remains off the dryer is ready to use Page 8 Routine Cleaning Cleaning the dryer
4. exterior N WARNING e Before you clean the dryer turn off the power switch Do not splash water on the dryer Ac ution Wear gloves when cleaning Clean the dryer with a soft cloth If the unit gets very dirty clean with a soft cloth dampened with neutral agent then clean with a dry soft cloth Remove the dirt from the sensor to prevent malfunction e Only use the neutral cleaning agents e Do not use thinners acidic or alkaline toilet cleaners Do not use a abrasive cleaners Alcohol may be used to clean the hand drying cavity area Do not use alcohol anywhere else Alcohol is intended for disinfection concentration below 83 MM The antibacterial coating is effective when bacteria is exposed the coated surfaces MM he antibacterial coating becomes ineffective when surfaces get dirty Draining and cleaning the tank Cleaning the air fiiter Frequency weekly Frequency Generally required weekly e Empty the drain water at any time to prevent accumulated Use a cloth to regularly wipe and clean water from overflowing drainage routes e Accumulated water may smell if left too long in the tank The water blown off hands is called drain water A Open the side panel with the allen key Pull the drain tank out in the horizontal direction This ensures the drain water does not spill Full level Drain tank Open the tank cover and empty the water Pull the cover up with you
5. ounding wire to prevent electric shock This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety If the cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons inorder to avoid a hazard For additional protection the installation of a residual current device RCD having a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom Ask your installer for advice Install hand dryers adjacent to wash basins out of the way of storage cabinets or other objects to optimise access and movement around the dryer In congested areas position dryers to ensure good traffic flow between wash basins and dryers If more than one is used dryers should be placed at least 600 mm apart Required Clearances From dryer to sides walls Minimum of 200 mm To ceiling or shelf above Minimum of 200 mm From the dryer bottom to the floor Minimum of 150 mm Page 3 Parts names and Dimensions Heat switch Speed regulator Check light Power switch Drain line Power light Drain tank Air filter 219 77 93 lt gt Tr Mounting plate Terminal box location INCLUDED IN THE PACKAGE m o
6. r fingers in the direction of the arrow on the top of the cover and then remove the cover completely Wash out the interior of the drain tank 2 Remove the air filter Close the tank cover and slide the drain tank back Sant air filter out by the into the dryer andle Cleaning the air filter Air filter Beat lightly by hand or use a vacuum cleaner If very dirtywash with warm water Place back into the dryer If you wash the air filter with water ensure it is dry before refitting
7. round Suitable fixed wire conductor size 1 0 2 5 mm A drop in voltage is possible if the power cord exceeds 11 min length so we recommend using a 2mm cord Fixed wiring Power cords with ground line LY For fixed wiring the wire should emerge from the wall at 630mm from the floor VA 80 mm from left side of the dryer G RIJA Fixed wire emerging from the wall should be not less than 400mm long Attach the mounting plate to the wall Attach the dryer to the wall using the appropriate fastener The wall should be reasonably flat Use washer s to fill gaps Wall types e Brick Concrete Use 6 mm x 40 mm e Stud Drywall Use 6mm x 40 mm screws Use 6 mm toggle bolts for dry wall plaster wall Mounting plate height For the standard dryer height 890mm floor to the bottom of the mounting plate 1 Remove the drain tank 2 Remove the front panel 3 For fixed wiring remove the terminal Remove the two screws box cover Remove the terminal box cover screw and remove the cover Remove the flexible power cord g el Fixing screw id Wiring access Attach the dryer to the mounting plate Mounting plate If fixed wiring is used pull the fixed wire through the wiring aparture from the rear of the dryer then attach hook the dryer onto the mounting plate Secure the dryer to the wall with the two bottom screws Expansion plug Position of low
Download Pdf Manuals
Related Search