Home
Triax C-HD207 CX_V.0183_englisch_D.docx
Contents
1. Select the line Antenna using AV and Terrestrial using the lt or gt buttons Select the line Search mode using AW and Antenna using the lt or gt buttons In the line Encrypted select whether the channel search should also include encrypted channels using the lt or gt buttons No encrypted channels will be ignored Yes encrypted channels will be included in the search Move the cursor onto the line Start scan using the AW buttons and start the search process by pressing the OK button Now two windows are shown listing the newly found TV and radio programmes The Status window shows how far the search has progressed Display Scanning gt Search is active Display Complete gt Search is finished You can leave this menu by pressing EXIT If not finished the channel search algorithm is aborted If new channels are found you are asked to store them Yes Select your choice by lt gt and confirm with OK If selected YES the new channels are stored at the end of the channel list now 17 Installation Manual channel search In manual channel search you can enter the channels to be searched directly In the nstallation menu move the cursor using the buttons AV onto the line Channel search and press the OK button The following menu will appear Channel search Antenna Cable Search mode manually Encrypted Modulation Symbolrate Channel This is how to perform a manual channel search
2. Connecting the receiver Connecting the receiver RF connection Connect the RF Input Digital connector 6 of the receiver to your cable signal wall socket Connecting a television Use a scart cable to connect the TV connector 3 on the receiver to the corresponding scart connector on the television set HDMI output 4 If your receiver is connected to the TV by a HDMI cable audio and videosignal are digital Connecting a digital multi channel amplifier optional The receiver is optionally available with an AUDIO OUT connector 8 for a DOLBY DIGITAL signal Use a suitable cable to connect this connector to your multi channel amplifier Connecting an external IR receiver optional If you want to set up the receiver where it can t be seen you can connect a so called IR mouse to the RJ 11 connector 9 This must be positioned in such a way that it can receive the signals from the remote control When installing the receiver always be sure to follow the safety and installation instructions Connecting an external mass storage device optional For recording of TV programmes an external mass storage device can be connected to the optional USB connector 5 Connecting the mains adaptor Connect the DC plug of the mains adaptor supplied with the unit to the connector DC INPUT 12V 2 on the receiver How to insert batteries into the remote control Open the cover at the rear side of the remote control Insert two AA
3. Triax C HD207 Digital Cable TV Receiver 305207 305208 Users Guide A Y l P B i Cah 64 L d R R o T O N k TRIAX your ultimate connection Content Content COMEN farses ta u ssa nossa sabensdnsa vonage acne ada sched wa tabouad nia yacnkedities tad at enetthont Unt E r ders 2 General MSU CH Ten 3 Make a contribution to environmental protection e eee ee ee eee 3 Saey TAS CUO IS macatitatacenocaycar ae tanandecastec tanita neisuien r a tate troerete hn et cad areca een eRe Bey 4 Gie aning Eae sacs sssnlensdenancomtdnauinesse ER a a E a otadenak a E E RARER AE 4 Control elements front and rear panel eee 4 Connecting THE reciver ee e a EE 6 PRE IMIOLS COMO Ea 0 i A A E A E eas 7 LAAT MS CaO NN TTT 8 Eeiz GTS ING ECCI TT 9 EPG Electronic Programme Guide sss sese ee eee eee 11 HII eect tahoe ae cachet HE tits ha tater etn naman nantes 11 Settings Receiver setup ee ee e ee e ee e ee ee 12 SONGS PIOU TTT 13 SUMING Ss OUI EH 14 SO Ie C SUD UNS tiiatasiatenctonate dadusneeduatrau E E Ee decuea teak ER 15 Settings OSD Configuration Option ccccssscecceseseeeeesseesseeseeesseeseeesseeeeeeseneeeessagees 15 SeNiNgS Parental lOCK hss eiserescatcutencesvasa T O E a cuteae 16 Parental OCK GevViCe lO CK aooe a E E E 16 Parental Lock changing The PIN aerei a a E e E A 16 ST L 17 Installation Channel search wei 28494 a 4 Ka 7 e aaa 20T TE aun 2 aan TR TAK ay HL 17 Manyakechanmmel Tee
4. m Stop button F1 F2 Remote control ON OFF button List Shows list of stations TR LIVE Switches between RADIO and TV mode OK In menu opens confirms or modifies currently selected item m Activates last selected channel OPTION Choice of audio channels FT F2 Opens specified menus VOL Volume control GELB Opens the voiman menu In menu Delete function mone No function JI Pause button Setting and managing of markers onun Renaming records Initial installation Initial installation After reading the safety instructions see chapter safety instructions and finishing the actions explained in chapter connecting the receiver please use the supplied power cord for connecting the apparatus to the power supply When running the receiver for the first time the welcome menu of the installation guide is displayed at the TV screen It helps you installing the most important settings ent ene Welcome In the first step of the installation guide please select your Menu language 2 14 language by using Aor W Confirm your choice by OK Deutsch English Italiano Suomi Francais e tina T rk e Country In the second step please select your country Therefore press A Y and then OK If you want to get back to the language selection you have to use the EXIT button Country 1 12 Germany Austria Switzerland It
5. will appear Use the lt b buttons to select whether you really want to delete the recording Yes or not No Confirm your choice with the OK button Record list 21 06 2010 18 30 Sports Sports 01 30 54 Newsflash 00 28 10 Movies 02 10 20 Soccer 00 45 00 Sorting recordings In normal operation press the Archive button to open up the list of recordings Press the LIST button The menu Select list will appear Use the AY buttons to select the sorting criteria and then press OK The list of recordings will be sorted as follows Alphabet The recordings will be put in alphabetical order Date of recording Sorted according to the date of the recording newest recording first Entry Sorted according to where the recording is filed on the mass storage device Recording length Sorted according to the size of the recording Renaming records While a recording is being made it s name will be formed automatically from the broadcast information You can however rename the recordings manually In normal operating press the Archive button The list of recordings appears Use AF to select the programme you would like to rename Then press the blue button This menu will appear Record list 21 06 2010 18 30 Sports 26 In the lower window you will see in the first line the name of the selected programme Below it available characters are shown Use the green button to switch between capital and low
6. Devi Information Formatting Information Move the cursor using the buttons A Y onto the line Information and press the OK button In the superimposed window you will see details about the connected mass storage device Type size etc Use EXIT to leave this window Formatting Allows you to format the mass storage device Formatting the mass storage device will completely delete all data which is recorded on it Afterwards the full recording capacity will again be available In the menu Mass Storage Device move the cursor using the buttons A Y onto the line Formatting and then press the OK button Recordings 4 of 999 Available space 69699MB xx J format No Use lt b to choose whether you want to format the mass storage device yes or not no After formatting the number of recordings will be reset to zero Available space shows the maximum recording capacity available on the mass storage device Use EXIT to leave the window Caution If you format the mass storage device all recordings on it will be irretrievably lost 25 List of recordings List of recordings In normal operation press the Archive button to open up the list of recordings Deleting recordings You can delete recordings you no longer need from the mass storage device Use A Y to select the recording you wish to delete Then press the red button A security question asking whether you really want to delete the recording
7. For cleaning the casing please use a soft damp cloth Do not use any washing up liquids that affect the casing Do not spray a cleaner towards the receiver PLACEMENT In touch with certain furniture surfaces it may happen that the receiver s feet may rub off You should place the device on a proper underground that is stable and not easily inflammatory Otherwise the receiver may fall and cause serious injury to people and serious damages to the device Do not use this product near water e g bath tube wash bowl Dumping hint for packaging Any packaging material is recyclable and should principally be supplied to the recycling process Packaging and wrapping materials as plastic foils etc should never be available for children Control elements front and rear panel 4 1 4 digit display shows channel number Display f Receiver in standby mode Channel number Timer activated 10 Smartcard reader Digital Receiver RF DIGITAL 2 3 4 9 6 7 AUDIO OUT IRIDATA 8 9 2 Connector for mains adapter 12VDC 3 TV Scart port for connecting the TV 4 HDMl Output digital Audio and Videosignal for connecting the TV 5 USB connector for external mass storage device Option 6 RF Input Digital Connector for cable signal 7 RF loop through Output Left side 8 Optical S PDIF Output for DOLBY DIGITAL Signal 9 RJ 11 Connector Connection for an external IR receiver and Interface for software update
8. Select the line Antenna using A Y and Terrestrial using the lt or gt buttons Select the line Search mode using A Y and Transponder using the lt or gt buttons In the line Encrypted select whether the channel search should also include encrypted channels using the lt or gt buttons No encrypted channels will be ignored Yes encrypted channels will be included in the search In the line Frequency use the lt gt buttons to select the channel that should be searched Move the cursor onto the line Start channel search using the A Y buttons and start the search process by pressing the OK button Now two windows are shown listing the newly found TV and radio programmes The Status window shows how far the search has progressed Display Scanning gt Search is active Display Complete gt Search is finished You can leave this menu by pressing EXIT If not finished the channel search algorithm is aborted If new channels are found you are asked to store them Yes Select your choice by lt gt and confirm with OK If selected YES the new channels are stored at the end of the channel list now Installation Factory reset This menu item allows you to reset the receiver to its default factory status Afterwards the receiver starts up with the Welcome Screen initial installation again 18 Installation Installation Software download With this function the operating software of the receiver
9. changes from amp to v select None at menu line Information keys lt or gt Start the update procedure by pressing OK in line start download You are informed about the download process immediately when the first data are received As the reception of the data happens blockwise several minutes may pass between the single data blocks When the first and second data block are received 100 the data are stored The storage process is signalled by flashing the numbers in the LED display Please wait until all data blocks are received When the update is completed the receiver automatically restarts and turns into Stand By mode Attention As long as the storage process has not begun the download can be cancelled by pressing EXIT at any time When the first data have been stored cancelling is no longer possible An interruption of the update process e g by pulling the power cable may damage the operating software receiver and the receiver does not work any more Hint If the download includes a new channel list the receiver needs to be reset to factory default status for activating this list after download is completed and receiver was restarted 20 Installation Smartcard Reader The Digital Receiver is optionally equipped with a smartcard reader With an equal smartcard it is possible to unscramble encoded channels The smartcard can be inserted also while the receiver is switched on Insert the smartcard g
10. ee ducneceay covet wa cen yiirir wed susmesen yeaa eoiaveoueus 18 lnStallation PaAClOry TESS O 18 Installation Software download esse sees ee ee eee 19 Installation Smartcard Reader Option sss eee eee 21 CHAMNEI TTT 22 Channel MSCs Cie All NSU TT 22 Channel list Edit favourites IIS eee ee 22 Channel list Delete all channels see eee ee ee eee eee 22 t Ens DEEE A L A E ETT 23 TINIE APO CONG ime a gama O E A E ewes 23 INFOPMAUIO MN xi ua nant cma rtakhuanemen saahdauandasxant sh ablalt nur menen saabdaunnnd Aa 24 WIG SOLE XC oaa ETE E A aaeactn evnenovaractes NE 24 Connection of external mass storage device option sss eee ee eee 25 2 LISE Ol LECOMGINGS eciersis ais cc ciedans det ed attienes he cuts tas cnedad sdea a E 26 Operating the external mass storage device Option cccecseeeceeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeeaes 27 Kee alle Retammree rite we teg tse ares tot etre anie Arr eat etter ert rt rere nn myer ng nt ere eee eee ae eter aa 27 Times NUNG Oese E a E aa a E EAEE ERREEN E 27 PAV DO ACK TTT 28 Choosing the audio channel for recordings ccccceeeeeeceeeeeeeeeeeeeeeeeaeeeeeeeeeeeeeeeneeeeeeanees 28 Fast torward and KS WING aene E R A A 28 Operating the hard disk setting and managing markers esse eee eee 29 Using seral Ten AGG es iia cn caverns a a ie eek wa dewernsaaseeninaesetced eaS 29 TROUDIG SHOOUAG TT 30 STAN Ee r TT 31 General instructions Warranty The period of
11. 2 Very fast rewind bn n a Maximum speed rewind 28 Operating the hard disk setting and managing markers During the timeshift function or playback you can mark places on the recording A marker is shown as a coloured triangle in the status indicator Press the button F1 at the playback position to set a marker You can use the button F2 to show a list of all the markers A recording always has the markers Start and End Using A Y you can now select a single marker Press the OK button to continue playback at the selected marker When the list of markers is open you can use the button to assign a particular function to a marker so that when playback reaches this marker the function is automatically performed You can assign the following functions to markers Press the button once the marker is interpreted as a loop When the playback reaches a loop marker it jumps to the previous marker A loop marker is labelled L in the list of markers A yellow vertical line is shown in the status indicator Press the button twice the marker becomes a jump marker When the playback reaches a jump marker it jumps to the next marker A jump marker is labelled J in the list of markers A white vertical line is shown in the status indicator Use jump markers e g to jump over commercial breaks Press the button three times this marker has no special function but can be used during playback as p
12. A type batteries 1 5V Attention Take care of appropriate polarity Note If the operational range of the remote control is getting smaller it indicates that the batteries are almost consumed Always replace both batteries Caution Do not heat disassemble or recharge the batteries Consumed batteries are not allowed to be disposed in domestic refuse They must be supplied to a facility collecting and disposing exhausted batteries according to the EU environmental protection rules Remote control u x MUTE Sound ON OFF Numeric input of channel numbers In Menu Input of numeric parameters frequency etc EPG Displays Electronic Programming Guide EPG Displays Programm Info lt gt Volume control In Menu Change parameters or scroll lists AV Channel UP DOWN In Menu selects menu lines a Leave current menu or OSD On Screen Display MENU Activates main menu Channel UP DOWN also in EPG Function Text Turns on Videotext Jia TLM K N E 5 8 j A o eo L L d J Ta EPG 0 om move Ee F3 F2 gt ARCHIVE E 1 E m i gt gt Ne L If external mass storage devices are connected 44 Fast rewind Opens list of __ recordings ARCHIVE b gt Fast forward 6 gt Playback button Record button Transfers EPG date into record timer
13. MI cable correctly No audio Volume is set too low Increase volume incorrectly Remote control does Distance to big Come closer to receiver point not work nei remote control directly towards receiver inserted incorrectly reachable by the IR signal remote control and receiver Timer is activated is activated Deactivate timer timer wrongfully and GMT is set incorrectly set time difference correctly wrong time and GMT is set incorrectly set time difference correctly Channel change on incorrectly screen graphic shows Channel has changed frequency Perform channel search No valid signal Incorrect Settings in menu Correct settings or restore the Settings factory default status 30 Technical data Technical data General e 6000 channels e On screen video text and VBI video text Fast OSD e quick channel change zapping e no delay at on screen graphic display e big type for better readability e concise help for all menus EPG e Electronic Programme EPG Channel list editor e copy replace delete e blockwise operations Channel search e automatic channel search e identification of encrypted channels e manual channel search Further details e Display for signal strength and quality e Separate audio output settings for SCART and Digital e SWAP function e DVB subtitling e DATA interface for updates and channel list transfer updates available via website Hardware CPU e 32 bit RISC CPU HDMI e with Upscaler
14. Selection of available data Depending on their availability in the update stream you can select the download of following data by pressing V A a Software Operating software b Channel list Channel list G OSD texts All menu texts displayed on the screen d Information Information concerning the available download data e g version number innovations etc 19 Installation If you want to update one of the options a to c press OK at the corresponding menu item If required by the receiver it may happen that there are selected additional menu items automatically In line Information you can specify if you want to receive further information on the selected data keys lt gt All Information on all available data None Information on none of the available data Software Information on the new software version OSD texts Information on the new menu texts Channel list Information on the new channel list Hint If you like to read these information before doing the update please leave menu items a to c inactive 9 and specify the desired information at d Then start downloading these data When received you can view the information at menu items a to c by pressing the yellow button For leaving the corresponding on screen graphic use EXIT please 3 starting the update The update download process is started as follows select the desired data pressing OK at a b or c mark
15. USB e USB 2 0 Option Video e 1x SCART with FBAS Y C YUV or RGB support e 16 9 signal Audio e Audio DAC e Optical audio out e Volume control Reception e 50 5 858MHz Band Ill IV V e 7 or 8 MHz bandwidth switching L Handling e Remote control rare panel control Power requirement e 12 Volt e Standby mode Low Power Standby ON lt 1W Low Power Standby OFF about 4W Batteries for remote e 2x1 5V size AAA control Surrounding e 5 C to 35 C temperature Dimensions eB x H x T 230 x 35 x 140 mm Weight e Ca 580g Subject to change without prior notice Errors in interpretation excepted 31 595 00193 TRIAX www triax com 02 2011 D This product complies with the requirements imposed by the 2006 95 EC repealing the 73 23 EEC Directive amended by the 93 68 EEC Directive and 2004 108 EC repealing 89 336 EEC Directive Directives Svend Kristiansen Quality Manager Triax A S Bj rnk rvej 3 8783 Hornsyld Danmark Electric and electronic equipment and included batteries contains materials components and substances that can be hazardous to your health and the environment if the waste material discarded electric and electronic equipment and batteries is not handled correctly Electric and electronic equipment and batteries is marked with the crossed out trash can symbol seen below This symbol signifies that electric and electronic equipment and batteries should not be disposed of with ot
16. aly Greece Portugal Hungary NOTE The choice of the country affects the the channel list sorting In the next step please select the parameters of your local Network network use A or V If you are not sure which type of modulation you have to use 6 900MS QAM256 please select QAM ALL for an automatic channel search 6 900MS QAM64 Only the symbolrate 6 111MS 6 875MS or 6 900MS must be 6 900MS S G selected 6 875MS QAM256 6 875MS QAM64 Confirm with OK 6 875MS anes 6 111MS QAM256 6 111MS QAM64 6 111MS QAM128 6 900 MS QAM ALL 6 875 MS QAM ALL 6 111 MS QAM ALL Operating the receiver Channel list sorting In the last step of the initial installation you are asked if the channels which are found during the channel search should be Welcome sorted automatically Note This function is only effective if accordant channel list informations are sent by the broadcast station manually automatically Use the buttons Y or A to select manually or automatically and confirm with OK Manually Channel list remains unchanged Automatically Channel list is sorted automatically The menu for automatic channel search and the search process will be started During the search the window shows Status scanning The newly found TV and radio programmes will be listed Once the search is complete the message Status complete is shown Use EXIT to leav
17. aying the alphabetic channel list and its char locator Then enter the char locator menu by pressing Use A Y and lt K for selecting the first letter of the searched channel and confirm by OK If available the channel list shows the wished channel now For re entering the channel list press for activating the channel use OK 10 4 Swap from current channel to the previous one Your receiver remembers the previous activated channel By pressing you can switch from the current to the previous channel By pressing again switch back to the current channel Every time you perform a channel change the title and start stop time of the current and the following programme are displayed in the channel change OSD on screen display Thereby the scale of progression below the programme number signals the temporal progress of the current programme If faded out you can display this information again by pressing OK EPG Electronic Programme Guide Almost all TV and radio broadcasters provide further information on their programme Your receiver stores and decodes these data and displays them in the so called Electronic Programme Guide EPG This programme preview is activated by using the EPG button The appearing list contains all programmes of the current channel In the headline of the menu channel name date and time are shown Das Erste HD Monday 19 12 2011 20 07 By using the buttons cH O the channel can be chan
18. children to operate this electrical device without supervisor ENVIRONMENTAL CONDITIONS Protect the receiver against humidity heat and cold Allow 10cm space around the receiver for sufficient ventilation Do not cover the receiver s ventilation openings with items like newspapers tablecloths curtains etc Do not place any objects filled with liquids such as vases on the digital receiver Take care that no foreign bodies or liquids are getting into the device Do not expose the digital receiver to dripping or splashing liquids CONNECTING TO MAINS SUPPLY SAFETY FEATURE Only connect the original mains adapter to a well reachable mains supply connector 230V 50Hz only Do not tilt do not use disproportionate power and do not damage the recever s power connector and its electrical connections when connecting the power cord If the mains adapter should fail to fit contact your supplier FAILURE If the mains adapter or the power connector or its electrical connection is damaged immediately unplug the mains adapter from the mains supply connector Do not try to open or repair the mains adapter or the receiver on your own Service must be carried out only by experts at a proper service centre If replacement parts are required only original components are allowed to use The use of unauthorised components may result in risk of fire and electric shock Cleaning and care Before cleaning unplug the device from the mains adapter
19. d on regardless of what PIN code has been set Use the A V buttons to move the cursor to the line New PIN and press the OK button Use the 0 9 buttons to enter a 4 digit PIN code the press OK Use the Y button to move the cursor to the line Confirm PIN and press the OK button Now confirm your entry by entering your chosen PIN code one more time then press OK Press Exit to leave the menu Use the lt b buttons to choose whether you want to store the changes made Yes or keep the previous settings No Confirm your choice with the OK button WARNING You must not forget the PIN code Should this happen please contact your specialist dealer 16 Installation Installation In the main menu select the line nstallation using AV and confirm with OK The Installation menu will appear Channel search Factory reset Installation Use the buttons AW to make your selection and confirm with OK Installation channel search You can choose between automatic antenna and manual transponder channel search The automatic channel search checks the whole VHF and UHF range for programmes you can receive Automatic channel search In the Installation menu move the cursor using the buttons AW onto the line Channel search and press the OK button The following menu will appear Channel search Antenna Cable Search mode automatically Encrypted No Modulation QAM 64 Symbolrate 6 900MS Performing an automatic channel search
20. e the search menu Operating the receiver Switching receiver ON OFF 1 This receiver is equipped with a low power standby circuit If this function is activated the standby power consumption of the receiver is less than 1W The function is switched ON or OFF in the menu SETTINGS RECEIVER SETUP Low Power Standby ON Switching on the receiver takes about 10 seconds Display boot Low Power Standby OFF Receiver switches ON immediately 2 The receiver is also equipped with the function Auto Standby This function can be activated or deactivated in the menu SETTINGS RECEIVER SETUP If Auto Standby is activated the receiver switches to Standby Mode after 3 hours running Precondition No timer is activated and no operations with the remote control during this time You can switch on the receiver by pressing 0 OK A Y or by using one of the numeric buttons 1 0 The last activated channel will be displayed e g 0015 The digital receiver is switched into standby mode by pressing 0 ATTENTION Only by pulling the mains adapter the receiver is disconnected from the power supply completely Operating the receiver TV amp Radio mode You can choose between the operation mode TV viewing TV channels and RADIO listening to radio channels by pressing TV R Volume control amp Muting The volume level can be adjusted by pressing lt gt or VOLAY The corresponding scale is displayed on the
21. econds Press EXIT to leave this menu If you want to store your modifications select Yes by pressing lt or gt For the restoring the previous settings you have to choose No Confirm your choice by using OK 15 Settings Settings Parental lock Your receiver is equipped with a parental lock This secures the receiver against unauthorised use When the parental lock is activated the receiver can only be switched on after entering a 4 digit PIN code Parental Lock In the Main menu use the A Y buttons to move the cursor to the line Parental lock and press the OK button Device Lock Change PIN Parental lock device lock To activate or deactivate the device lock move the cursor to the line Device lock and press OK The following menu will appear Lock Device CO Use the gt buttons to switch the device lock on or of When the lock is activated the PIN code must be entered when switching on the receiver Press EXIT to leave the menu Use the lt gt buttons to choose whether you want to store the changes made Yes or keep the previous settings No Confirm your choice with the OK button Parental Lock changing the PIN To change the PIN code move the cursor to the line l y Change PIN Change Pin and press OK The following menu will appear New PIN ee Confirm PIN iN EER The PIN code is set at the factory to 0000 Using the code 9976 the receiver can always be switche
22. er case letters In the name use the red and blue buttons to select the characters you wish to change The current position that can be changed is highlighted in colour Now use the AV and lt P buttons to select the character you would like to insert Then press OK to insert the character in the name To accept the new name press EXIT The newly modified name will now be shown in the list of recordings Operating the external mass storage device Option If an external mass storage device is connected to the USB Connector option on the rear side of the receiver you can store recordings on it The recording capacity depends on the size of the mass storage device and the data volume of the broadcast material Recording Various modes of recording area available for you to record programmes onto the mass storage device 1 Immediate recording Switch on the channel you want to record Press the red record button to record the current programme While the recording is running the programme continues to be shown on the screen To stop an immediate recording press the stop button 2 Timer recording You can record programmes onto a connected mass storage device in your absence using the Timer recording function Programme a Time recording as described in the chapter Timer Select the menu item Record on the mass storage device Select a channel during a record During a record all channels in the channel list which are
23. g options YcbCr or RGB gt Input 1280x720 Output 1280x720 gt Input 1920x1080 Output 1280x720 3 Display format Use lt or gt for selecting the screen format of your TV set 4 3 16 9 13 Settings 4 Display adjustment Use lt or gt for adjusting the video signal pan amp scan letterbox or pillar box 5 Videosystem Use lt or gt for adjusting the video system AUTO PAL NTSC 6 Picture scaling Here you can choose the picture resolution 720 x 576 1280 x 720 1920 x 1080 a Television connected to Scart Connector If your TV is only connected to the scart connector of the receiver you get the best picture quality if you choose in the menu item Picture scaling 720x576 for all output signals b Television connected to HDMl Connector If your TV is only connected to the HDMI connector of the receiver you get the best picture quality if you choose in the menu item Picture scaling Input signal Output signal If you prefer fast channel switching all output signals must be the same Press EXIT to leave this menu For storing your modifications select Yes lt or gt for keeping the previous settings select No Confirm your choice by pressing the OK button Settings Sound Sound settings Stereo Sound channel TV Stereo Sound channel Dig Uncompressed PCM 1 Sound setting Using lt or gt you can activate following audio modes Stereo Mono left or Mono right 2 Sou
24. ged without leaving the EPG menu With AV or lt gt you can select the broadcast you want to be informed about You can get more detailed information by pressing OK Also you can use the EPG list to program a record timer very easily Just press the Record button and activate the record timer in the corresponding menu Please use EXIT to leave this on screen dialog Settings The basic functionality of the receiver is defined in the Settings menu The derivation of your local time against the GMT Greenwich Mean time time needs to be corrected otherwise the displayed times may be wrong Hint At each on screen display the possible user inputs are explained in the help bar at the lower screen brink By pressing lt and gt you can change the corresponding settings When leaving a menu EXIT button you will be asked to store the performed modifications Yes or to keep the 11 Settings previous settings No Please choose one of these possibilities by pressing lt and gt and confirm your choice by OK Turn on the receiver by pressing For entering the main menu please press the MENU button The main menu is displayed Note Mass Storage Device is only displayed when an external mass storage device is connected at the USB Connector of the receiver Press the OK button The following menu is displayed Choose the menu item Receiver Setup by pressing AV and confirm by OK Settings Receiver
25. he channel list please press the red button on your remote control For leaving this menu please press EXIT If the Save popup appears please select if you want to store your modifications Yes or keep the previous settings No Confirm your choice by pressing OK 22 Timer Timer You can use the record timer functionality to programme a recording for a connected video recorder Totally 10 record timers can be activated Or you can use the sleep timer to specify a time at which the patie G imer receiver is to switch into standby mode Record timer Sleep timer Therefore please enter the Main menu by pressing Menu then select menu item Timer and confirm with OK Timer record timer Use A Y to select line Record timer in menu Timer and press OK The following menu appears Record timer Timer index 1 30 1 inactive Start at 00 00 Uhr Stop time 00 00 Uhr Date of recording 01 07 09 Station 1 Das Erste Repetitions nothing Programming a record timer Select line Timer index 1 10 with AV There select timer place with lt gt Select lines Start at Stop time or date of recording with using AV and confirm with OK Enter the required time or date by pressing 0 9 Confirm your input with using OK Select line Station with AV and confirm with OK Select a channel with AV or lt gt and confirm with OK Select line Repetitions with AV and use lt gt to specify the number of repetitions of this
26. her household waste but should be disposed of separately As the end user it is important that you submit your used batteries to the appropriate and designated facility In this manner you make sure that the batteries are recycled in accordance with legislature and will not harm the environment All cities have established collection points where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites or be collected from the households Additional information is available at the technical department of your city F K TRIAX your ultimate connection
27. in white colour can be seen Channels which are black cannot be seen during a record The channel which is recorded is marked with a red point in the channel list Timeshift function The Timeshift function enables you to record and playback at the same time This gives you various options 1 Time delayed television You can watch the beginning of the recording and jump over recorded passages e g commercial breaks Press the red record or the PAUSE button to start a timeshift recording To watch the partially recorded programme press the Playback button The programme is then played from the moment of recording while the current programme continues to be recorded in the background If you want to stop the playback and return to normal TV operation press the Stop button To stop a timeshift recording press the Stop button 27 Playback 2 Recordings saved on the mass storage device can be played during timeshift recording During the timeshift recording press the Archive button to open the list of recordings Use AY to select the recording you wish to see Press OK to start the playback The playback information will be shown on the screen If you want to stop the playback and return to normal TV operation press the Stop button To stop a timeshift recording press the Stop button Playback In normal operation press the Archive button to open the list of recordings Use A Y to select the recording you wish to see Press OK to
28. ion are displayed With A V you can change the channel Use EXIT to leave this menu Teletext Press the TEXT button to display the videotext of the current channel The first site to be seen is site number 100 In order to view a specific page use the buttons 0 9 to enter the three digit page number Your input is displayed in the left corner on the screen When the site number is input completely the receiver starts to search the corresponding site Because the video text sites are sent site by site it may take some seconds until the required site is found Enter 100 at any time to return to the home page of the videotext You may use Y to quickly page through the complete videotext section of a particular TV channel If you press the TEXT button again you can switch into the mixed mode background transparent Use the TEXT button to return to the normal mode For leaving the video text please press EXIT 24 Connection of external mass storage device option Connection of external mass storage device option If an external mass storage device is connected to the USB Connector option on the rear side of the receiver it can be managed in the menu Mass Storage Device Important Before connecting or disconnecting the mass storage device the receiver must be switched to Standby In the Main menu choose the line Mass Storage Device with AV and confirm with OK This menu will appear Mass Storage
29. it s menu texts and channel list can be updated Precondition is a Download channel allocated by your cablenetwork provider You can gather informations from you cablenetwork provider Your currently active channel list is not changed by a software update Attention In case of a software update the current operating software will be erased and a new software version will be installed When updating the channel list the factory default channel list will be replaced by a new one When updating the OSD texts all menu texts are erased and actualised The update process is subdivided into following steps 1 Select the channel with the download informtion 2 Open Update Menu Enter the nstallation menu select line Software download and confirm with OK The Download menu for controlling the update process is opened and the search for the download channel starts automatically Download Software New Software available v Channel list z X OSD texts Information Nothing Start Download New Software available Please wait until this search is completed It may take a few minutes When the download stream is found the receiver verifies whether there are available new versions of the operating software OSD texts and channel list The result is shown in the Download menu behind the corresponding menu items marked by If there are no new data available this is signalled by a You can leave the download menu by EXIT 3
30. lace for a loop or jump Press the red button to delete the selected marker from the list The Start and End markers K 00 17 22 yy E 00 20 30 cannot be deleted Press the F2 button or EXIT to close the list 1 00 00 00 Start 2 00 03 11 Mark1 J 3 00 08 58 Mark2 4 00 12 01 Mark3 L 5 00 20 30 End Using serial interface The serial data interface DATA offers you the possibility to connect the receiver to a PC Therefore you need a PC and serial cable On the PC side a female SUB D connector with 9 or 25 pins and on Receiver side a RJ11 plug with 6 pins Via this connection you can perform software updates and channel lists up and downloads The required information and software tools are available at the manufacturer s homepage 29 Trouble shooting Trouble shooting Every electric device can have a malfunction It does not automatically mean that it is defective In most cases it happens because of a feed cable plug and connector connections or access mistakes Please control the following items before taking the receiver to your specialised dealer Receiver can not be Mains adapter not connected to Check if mains adapter is turned ON i plugged in correctly Try another electric device at the same power connector are not TERE inserted faulty No or bad picture TV set E n ns on wrong en set up of the TV set E n ns Scart or HDMI cable is damaged baian or plug in the Scart or or plugged in incorrectly HD
31. mations are sent by the broadcast station Use the buttons Wor A to select automatically or manually and confirm with OK Automatically Channel list is sorted automatically Manually Channel list remains unchanged The channel list can be changed in the menu Channel list 8 Channel list update Use the buttons lt P to choose automatically or manually mode If you choose automatically the automatic channel search is activated when the receiver is switched to Standby If you choose manually there is no channel search active If you switch on the receiver after new channels where found the following menu is displayed New channel list received Store Yes No Use the buttons lt P to choose yes or no Yes The new found channels are added at the end of the channel list No The new found channels will be deleted Settings Picture For entering the Picture menu select menu item Picture in the Settings menu and press OK The following menu appears 1 Analog Video The analog video output at the SCART connector can be adjusted by pressing lt or gt Analog Video RGB You can select among following options FBAS Digital Video YCbCr RGB or YUV Display format 16 9 Display adjustment Letterbox 2 Digital Video Videosystem Auto The digital video output at the HDMI connector Picture scaling can be adjusted by pressing lt or gt You can gt Input 720x576 Output 1280x720 select among followin
32. nd channel TV If the broadcasted programme offers different audio options you can select the desired audio output at the TV Scart by keys lt P gt 3 Sound channel digital If the broadcasted programme offers a digital audio channel you can use lt gt for selecting the audio signal that is to be output at the digital audio port Press EXIT to leave the menu If you want to save your modifications choose Yes for restoring the previous parameters choose No keys lt P gt Confirm your choice by pressing the OK button 14 Settings Settings Subtitle Subtitle Subtitle language 1 Subtitle By using lt gt you can activate deactivate the display of DVB subtitles if transmitted 2 Language of the subtitle To select the language of the subtitle you must use lt or gt If there is no subtitle available this is indicated by By default the subtitle is in accordance with the menulanguage Use EXIT to leave the menu If you want to save the modifications choose Yes for restoring the previous parameters choose No keys lt P gt Confirm your choice by pressing the OK button Settings OSD Configuration Option For entering the OSD configuration menu please select menu item OSD configuration in the Settings menu and press OK The following menu appears OSD Configuration Display time By using lt or gt you can modify the display duration of the channel change graphics 1 10 s
33. olden chip on lower side towards the receiver carefully into the slot at the front panel of the receiver SMARTCARD After the smartcard is inserted the encoded programmes will be unscrambled To open the menu of the smartcard first select Installation in the main menu and press OK to confirm A submenu generated by the smartcard appears on the screen e g Conax or CryptoGuard Channel search Select the submenu of the smartcard with A or Y and Factory reset press OK to confirm Software download For more information on using the smartcard see the menus Conax shown or it s instruction manual 21 Channel list Channel list You can resort and or erase TV and radio channels found in the course of an automatic channel search This function is Channel list available for all TV and radio channels Edit main list For entering the corresponding on screen dialog please Edit favourites list press the Menu key to enter the Main Menu then select Delete all channels menu item Channel List and confirm with OK Channel list Edit main list This sub menu enables you to erase or move certain channels in the channel list For entering this menu simply enter OK at line Edit main list a Erase channels Select the channel to be erased with A Y and mark it with OK You can select more channels by pressing A Y and OK To erase them press the red button b Sort channels Select the channel to be sorted by
34. record 8 Select line Activate timer and activate the programmed record timer by pressing OK there text Activate timer changes to Deactivate timer OY Ol he N The receiver will switch on at the programmed time and signals a timer record by displaying rEC in the 4 digit LED Display If you want to abort a record please enter the record timer menu and deactivate the timer by pressing the Deactivate button Record active Stop If you push one of the buttons AV or lt P following menu appears Vag No Choose Yes to stop the record or No to continue the record Hint Please make sure that the local time of the receiver is set correctly and the video recorder is programmed too 23 Information Information Enter the main menu there use A Y to select line Information and press OK In the upper section of the menu the channel parameters of the activated channel are displayed In the lower section of the menu the signal qualities are displayed C N The further the bar turns right and the higher the dB value the better the signal quality Level The further the bar turns right the better the reception Hint The power of the signal depends on the antenna set up and also on the currently activated channel Please remember this if you want adjust your antenna by controlling the signal power After pressing the lt K or the yellow button two further charts with channel software and hardware informat
35. screen Hint It is not possible to change the volume level while the menu is active The volume control only affects the audio output at the TV VCR and AUDIO ANALOG OUT ports of the receiver By pressing the R button you can totally switch off the audio output muting For switching on again simply use the same button Selecting a channel 1 Using the directional up down keys To change the channels stepwise press the buttons A Y In order to switch the channels quicker hold these buttons pressed longer 2 Using the numeric keys direct input One or more digit channel numbers can be input by using the numeric buttons 0 9 and pressing OK Not available channel numbers are ignored 3 Using the channel list By pressing the LIST button the last activated channel list or favourite list is displayed Browse the channel list by pressing lt gt or A Y and activate the desired channel by pressing OK When pressing key LIST twice the following menu appears Favourites List Your personal list of favourite channels Favourites list Radio List List of stored Radio channels Radio list TV List List of stored TV channels TV list Alphabetic List List of stored TV or RADIO channels in Alphabetic list alphabetical order Choose the favoured list by pressing A Y and activate it by pressing OK In alphabetic list mode the channels are sorted alphabetically It helps you searching a certain channel Therefore press LIST for displ
36. setup The following menu is displayed Receiver setup Time difference Menu language 2 00 Std English Initial volume 90 HDMI Audio Bitstream Off Auto Standby On Low Power Standby On Channel list sorting manually Channel list update manually 1 Time difference Settings Installation Channel list Timer Information Mass Storage Device Receiver setup Picture Sound Subtitle OSD configuration Parental lock When operating the receiver for the first time you should set the derivation between your local time and the received GMT time Greenwich Mean Time by pressing lt or gt For Central Europe the following settings are recommended 1 00 hour 2 00 hours Winter time Summer time Note This setting has to be updated at each summertime shift 2 Menu language Choose your language by pressing lt or gt 3 Initial volume 12 Settings The initial volume after a power reset of the receiver is adjusted here by pressing lt or gt 4 HDMI Audio Bitstream HDMI Audio Bitstream can be switched ON or OFF by pressing lt or P 5 Auto Standby Auto Standby function can be switched ON or OFF by pressing lt or gt 6 Low Power Standby Low Power Standby function can be switched ON or OFF by pressing lt or gt 7 Channel list sorting If you choose automatically the channel list is sorted automatically Note This function is only effective if accordant channel list infor
37. start the playback Playback is stopped using the Stop button Choosing the audio channel for recordings When playing back recordings you can choose between the different audio channels During playback press the button Option Now a menu with the available audio channels will be shown Use the A Y buttons to select the audio channel you want to use and press the OK button Pressing the EXIT button to hide the menu again Fast forward and rewind During playback press the Fast Forward button or the Fast Rewind button The symbol P mor lt lt will appear and the recording will be played faster in the desired direction Press the Fast Forward or Fast Rewind button again to increase the speed The symbols gt gt gt or lt lt lt will appear Press the Fast Forward or Fast Rewind button once more and the speed will be increased to the maximum The symbols gt gt gt gt or 4222 will appear Once you have found the spot you were searching for press the Playback button to return to normal playback operation During fast forward or rewind you can use the lt b buttons to change position within the file This enables you easily to jump over longer sections of film Overview of symbols displayed Indication Meaning gt Playback gt gt Fast forward gt gt p gt Very fast forward gt gt gt K Maximum speed forward 6 Record o gt Timeshift operation lt lt Fast rewind 44
38. using A Y and mark it with OK You can select further channels by pressing A V and OK max 20 channels can be selected at the same time Use A Y to select the position where to insert the marked channels and confirm with the yellow button Channel list Edit favourites list This sub menu allows you to add your favourite channels to the favourites list Therefore please press OK in line Edit favourites list Now two lists are displayed the Main list all stored channels are listed max 6000 the favourites list contains your favourite channels max 4000 Now you can select your favourite channels from the Main list and copy them into the favourites list Select the channels you like to add to the favourites list by using A Y and mark them with OK Then press button to enter the favourites list There use A Y to select the position where to insert the channel and press OK With you return to the main list again Use EXIT to leave the channel list menu By pressing lt b you can store your modifications Yes or keep the previous settings No Confirm your choice by OK In radio mode you can create your own favourites list for radio programmes too Channel list Delete all channels This dialog allows you to delete all channels from the channel list Therefore please enter menu Channel list and select menu item Delete all channels OK Select Cable with A VW and mark it with OK For erasing the channels from t
39. warranty starts when buying the device Please verify the exact date by sales check delivery note invoice etc Keep the documents carefully Our warranty service refers to our warranty terms valid at the time of buying the apparatus In case you require technical service please take or send the device to your specialised dealer The unit is labelled with the CE sign and therefore conforms to the general requirements of the European guidelines The Declaration of Conformity is found in the later part of this manual Make a contribution to environmental protection Do not throw batteries into domestic waste As a consumer you are obliged to return used batteries You can bring them to a public collection station in your commune or elsewhere where batteries of the same type are sold The following signs can be found on batteries including harmful substances Pb battery includes lead Cd battery includes cadmium X X X Pb Cd Hg Hg battery includes mercury Hints for disposal IS If your device is once disused you should not just throw it into domestic waste Ex si Surely there is a collecting point for old devices where it can be collected and recycled Safety Instructions Safety Instructions Before installing your digital receiver all security and operating instructions should be read carefully The User s Manual should be retained for future reference All operating and using instructions should be followed Never allow
Download Pdf Manuals
Related Search
Related Contents
Shark 100S User Manual V.1.15 INFORMATION 取扱説明書 (PDFファイル Installations-Bedienungsanleitung Dachventilator Vertikal EC A5 - Manual de Vta 110 STD - FULL Copyright © All rights reserved.
Failed to retrieve file