Geartronics paddleshift quick setup guide
Contents
1. you will need to re sample the gear positions or make individual trim adjustments To select neutral from 1 gear you need to press the interlock button and simultaneously pull the down paddle There is an option in the software to allow the selection of neutral simply by pressing the button from 1 gear only On gearboxes with a shift to neutral Sadev amp some Hewland it is may be necessary to experiment with the click timer settings on the gear positions page Please consult Geartronics technical for advice If the shift test in the workshop works OK then you can conduct further testing on the track Before the car is driven on track please delete the data log The initial track test should be limited to a single installation lap at reduced speed amp load after which the data logging should be examined to check for reported mis shifts etc The fastest shift times should be in the order of 30 40ms Slowest shift times should generally be less than 150ms However these times are only approximate and can vary considerably depending upon gearbox type and engine response The only parameters that you may need to alter in the GCU are the downshift throttle blip settings Providing that the spark cut is functioning correctly the up shifts should be fast and smooth When correctly set the downshifts should also be fast and very smooth Data logging It is recommended that the data log is saved to disk and then deleted from2. the GCU after each session As a general rule the fastest shift times should be in the order of 30 40ms depending upon gearbox type On a well designed and well maintained racing transaxle the fastest shift times may come down to as little as 20 30mS However the slowest shift times can exceed 150ms in certain circumstances The way in which the GCU logs data means that you will probably see some reported miss shifts Do not be alarmed unless there are a significant number or unless the driver is reporting a problem The GCU will log a failure if a shift has taken longer than the time allowed This does not necessarily mean that the shift has actually failed and in most cases the driver will be unaware of any problems The data logging could be configured in such a way as to not report any problems but this would be counter productive as it would not give us any indication of potential problems Summary The Geartronics GCU shift strategies have been developed over a period of several years in many and varied applications The default parameters have been found to give acceptable results in most applications We would advise that you do not adjust these parameters unless you have a full understanding of sequential gearbox dynamics and the effects that any parameter changes might have There is a detailed software manual on the setup CD that explains the function of each parameter If you are unsure about anything then please contact Geartronic
3. Geartronics paddleshift quick setup quide The following instructions are intended to help you setup the paddleshift software as quickly and as easily as possible More detailed information can be found in the full user manual which is located on the setup CD These instructions assume that the hardware is fully installed and that the GCU is connected to all the necessary sensors and that the pneumatic system is complete with all air connections secured Important before powering on the system for the first time ensure that the compressor is DISCONNECTED or the compressor relay is removed to prevent the compressor from running The reverse neutral interlock mechanism on the gearbox should be removed and blanked off except Ricardo 500Nm box this function is replaced with the neutral interlock button on the steering wheel Establishing communication with the GCU The most reliable method of communication is via the RS232 serial port connected directly to a serial port on your laptop computer The pin out of the serial lead should be as follows 9 way D male 9 way D female 2 2 3 3 5 5 If your laptop is not fitted with a serial port a serial to USB converter may be used However these are often unreliable and it might be a better option to use the built in USB port on the GCU When first connecting the GCU to
4. ack on To calibrate the throttle click the box entitled Use Throttle Sensor then click Calibrate Throttle Follow the on screen instructions When complete download the settings to the GCU by pressing F8 Check that the throttle indicator moves between 0 100 as the throttle is operated The Downshift inhibit should normally be set to Use multiple RPM thresholds The base RPM threshold should then be set to the maximum permitted engine speed after a downshift The actual RPM limits are then calculated from the programmed gear ratios Clutch position monitoring is not normally required unless the car is to be driven by inexperienced drivers When the clutch position is not used the input pin can be re assigned to function as an emergency or limp home switch Setting gear positions The Geartronics paddleshift system relies on accurate gear position sensing The GCU therefore needs to learn the positions of each gear on the selector barrel Select the gear positions page First we must specify the order of the gears on most gearboxes this will be N123456 even if your gearbox has a reverse gear but some Hewland gearboxes have the neutral position between 1 amp 2 1N23456 There are two other gear order options but these are only used for two specific gearboxes We can now programme the gear positions by selecting Sample Gear Positions and following the on screen instruction
5. are necessary To save the file click file then save as By default the calibration file will be saved to the program files geartronics profiles folder System testing The system can now be powered on with the compressor connected On initial power up the compressor should start and you should see the pressure indicator in the software rising If the pressure does not increase switch off immediately and investigate the problem When the pressure has risen to 150psi the compressor should turn off The compressor will initially run for about 50 60 seconds When the system is fully pressurised and the compressor turns off you can test the actuator amp blipper functions form within the Test page To test the blipper click the box entitled throttle blip 250ms The mechanical blipper should be initially adjusted to give approximately 20 25 throttle opening The blipper operation can be verified by looking at the real time throttle measurement at the bottom right of the screen Final throttle blip settings can only be determined by track testing As a general guide low inertia high revving race engines require less throttle blip than large low revving production engines To verify the correct operation of the gearbox actuator perform the following test Position the wheels so that you can select 2 or 3 gears without the need to turn the wheels further Click the data logging page and select Delete data lo
6. at any time by pressing F5 Note that uploading settings will overwrite any changes that have been made on screen To save changes that you have made on screen to the GCU press F8 Initial system checks At the bottom left of the screen you will see some status indicators Operate the up amp down paddles the neutral interlock button the clutch limp home switch and the auto switch if fitted As the paddles amp switches are operated the corresponding LED should illuminate When the system is first powered up with the compressor disconnected the pressure indicator should read OOO psi and the compressor LED should be illuminated Setting the Vehicle Profile options When the software is launched the default page is Vehicle Profile In this page we calibrate the following functions Tachometer engine RPM settings Throttle settings Downshift RPM limit Clutch settings Number of gears Gear ratios To check the calibration of the tachometer engine RPM ensure that the gearbox is in the neutral position and start the engine If the tachometer reads incorrectly you will need to change the number of pulses per engine revolution at the top left of the screen Note that the default tachometer range is 0 10 000rpm this can be increased by selecting settings then rev counter range When you are satisfied that the tachometer is calibrated correctly turn off the engine then switch the ignition b
7. g Using the shift paddles select the gears up and down several times without turning the wheels Click Load data log Examine the fastest up and fastest down times The above test should produce shift times of less than 50mS preferably 20 30mS Static shift times longer than 60mS indicate that there is a problem either with the mechanical installation or an air pressure problem If the shift times are too slow please consult Geartronics for advice before going any further If everything appears to be working OK and the static shift times are fast enough you can then proceed to the next very important stage of testing Shift cut torque reduction test We now need to test the function of the spark cut or torque reduction It is extremely important that the duration of the torque reduction is controlled by the GCU If you have connected the cut signal from the GCU to the engine ECU then you must ensure that the ECU is configured to cut the engine while ever the cut signal remains present Please consult your ECU supplier or Geartronics technical for advice To test the function of the shift cut perform the following procedure Select the Test page in the Geartronics software Set the test spark cut to 50mS Start the engine and run at approximately 3000rpm Click the spark cut box and you should hear a slight engine cut Now set the spark cut to 250mS Click spark cut again and the engine should almost s
8. s When the software prompts you to select each gear you must at this stage select the gears manually When all the gears have been sampled the barrel rotation dial will display a series of coloured windows which in most cases should be equally spaced around the dial The 0 360 position must be between the lowest and highest gears and the sensor must not pass through this position when any of the gears are selected If two adjacent gears are spaced either side of the 0 360 position then please contact Geartronics for advice The Gear position tolerance should normally be set to 5 or 6 degrees Once sampling is complete you should download the settings to the GCU by pressing F8 The numerical gear indicator on the dashboard and in the software should now correctly indicate the selected gear After the gear positions have been programmed and downloaded to the GCU check that the indicator dial moves to the centre of each coloured window as you manually select the gears both up and down the box Each gear position can be individually adjusted by 5 by clicking on the arrows by the side of the gear positions table at the left of the screen Remember to press F8 after any changes have been made After these initial settings have been completed you are advised to save the configuration file and send a copy by email to Geartronics technical We can then check that the calibration is safe to test the system and make any changes that
9. s technical before making any changes
10. the laptop using a USB cable you will be required to install the Windows drivers which can be located on the setup CD When USB installation is complete Windows will create a virtual COM port and assign it a COM number Start the paddleshift software and turn on the ignition If all is well the connection status message at the bottom of the screen should illuminate green to indicate that the GCU is connected You should also be presented with a dialogue box asking if you would like to upload the current settings from the GCU answer yes to this message If the connection indicator is red then this indicates a connection problem To check the COM port number click on Settings and Communications at the top of the screen When using a direct serial connection the COM port should match the COM port number of the laptop usually COM1 For USB connections the virtual COM port number will be indicated in the pull down box if the drivers have been installed correctly The GCU is supplied with factory default settings that will give an acceptable shift speed amp quality in most applications There are more than 80 configurable parameters that govern the shift strategy These parameters should be left at their default values unless you fully understand the consequences of any changes that you make The exception to this rule is for the essential configuration changes as described below Current GCU settings can be uploaded to the PC
11. top DO NOT under any circumstances operate the system on track until the shift cut test has been verified Incorrect shift cut setup can result in serious gearbox damage Note final ECU torque reduction parameters should be determined by track testing For the purposes of a workshop test the torque reduction can be set to 100 total ignition cut Initial shift test It is strongly recommended that the initial shift test is conducted with the car on stands and the driven wheels removed Assuming that the gearbox is in neutral start the engine depress the clutch and select first gear by pulling the up paddle If a clutch switch is not fitted you will also need to press the interlock button to select 1 gear If 1 gear doesn t engage immediately keep the pressure on the paddle and slip the clutch until the gear engages Release the clutch and go up the gearbox using the paddles Do not press the clutch or reduce the throttle during the shift When you have selected top gear hold the engine at 4000rpm release the throttle and immediately pull the down paddle Each downshift should produce a throttle blip A static workshop test will usually result in quite harsh shifts which will improve once the car is tested on the track this especially applies to downshifts During the shift test check the barrel position indicator in the software and ensure that the dial moves to the centre of each coloured window as you select the gears If not
Download Pdf Manuals
Related Search