KPC-1550 User Manual
Contents
1. Figure 1 Rear I O Power Input The supplied power adapter converts AC power to DC for use with this jack Power supplied through this jack supplies power to the PC To prevent damage to the PC always use the supplied power adapter PCI Slot The PCI slot enables user to insert one add on card for expansion Power Switch The power button allows powering ON and OFF the system Audio Out The stereo headphone jack is used to connect the system s audio out signal to amplified speakers or headphones MIC IN The microphone jack is designed to connect the microphone used for video conferencing voice narrations or simple audio recordings Line IN The Line in jack is designed to take input from a higher powered sound source KPC 1550 User s Manual 16 USB The USB Universal Serial Bus port is compatible with USB devices such as keyboards mouse devices cameras and hard disk drives USB allows many devices to run simultaneously on a single computer with some peripheral acting as additional plug in sites or hubs Ethernet The eight pin RJ 45 LAN port supports a standard Ethernet cable for connection to a local network HDMI HDMI connector for display output DVI D Connector for DVI D VGA D Sub 15 pin VGA connector for display output COM D Sub 9 pin connector for RS 232 connection Side View Figure 2 Side View KPC 1550 User s Manual 17 Mechanical Dimensions 62 46 mm 80 5 mm T4 mm 71 5 mm 314 982. American Megatrends Inc Save Changes and Exit Exit system setup after saving the changes Once you are finished making your selections choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off When you select this option a confirmation window appears Select Yes to save changes and exit Discard Changes and Exit Exit system setup without saving any changes Select this option only if you do not want to save the changes that you made to the Setup program If you made changes to fields other than system date system time and password the BIOS ask for a confirmation before exiting Discard Changes Discards changes done so far to any of the setup values This option allows you to discard the selections you made and restore the previously saved values After selecting this option a confirmation appears Select Yes to discard any changes and load the previously saved values Load Optimal Defaults Load Optimal Default values for all the setup values This option allows you to load KPC 1550 User s Manual 37 optimal default values for each of the parameters on the Setup menus which will provide the best performance settings for your system The F9 key can be used for this operation Load Failsafe Defaults Load Optimal Default values for all the setup values This option allows you to load failsafe de
3. Advanced Menu Advanced Chipset Power Security Onboard I O Configuration Allows BIOS to Select Serial Port1 Base Addresses COM Address 3F8 COM1 IRQ 4 COM Function Type RS232 COM2 Address 2F8 COM IRQ 4 Select Screen COMS Address SE8 COMS IRQ 10 COM4 Address 2E8 COM4 IRQ 11 Parallel Port Address 378 Select Item Change Option F1 General Help F10 Save and Exit ESC Exit Parallel Port Mode Normal Parallel Port IRQ IRQ7 V02 67 C Copyright 1985 2006 American Megatrends Inc Press Enter to select a sub menu for detailed options COM1 Address Options Disabled 3F8 3E8 2E8 COM 1 IRQ Options 3 4 10 11 COM1 Function Type Options RS 232 RS 422 RS 485 COM Address Options Disabled 2F8 3E8 2E8 COM2 IRQ Options 3 4 10 11 COM3 Address Options Disabled 3F8 2F8 3E8 2E8 2F0 2E0 COM3 IRQ KPC 1550 User s Manual 28 Options 3 4 10 11 COM4 Address Options Disabled 3F8 2F8 3E8 2E8 2F0 2E0 COM4 IRQ Options 3 4 10 11 Parallel Port Address Options Disabled 378 278 3BC Parallel Port Mode Options Normal EPP ECP EPP ECP Parallel Port M IRQ Options IRQ5 IRQ7 Table 6 OnBoard Peripherals Configuration Settings OnBoard Peripherals Configuration Settings USB Functions 12 USB Ports Disabled 2 USB Ports Legacy USB Support Enabled 4 USB Ports Audio Controller Enabled 6 USB Ports Onboard LAN1 Controlle
4. Chapters JAM BIOS SEUD cissossspasvenseaanpsavsay vase ba d 25 SIMI 25 Main RT TTE a RR 26 POV ANCE Menti NETT TNT 28 BOO MAR LT TM 32 CAPSE MENU a ae ai eod aaa ba vasa sk 33 I2 0WBeF MO sasa k do ez 35 CUNY VIS DUE coo cnc a eR d a Gto t Dota rt Gale R Geta Goes 36 EX IVS Ul Tm 37 Chapter 4 Driver Installation a aainaaaaaaaaanaannaaanaaannannannanannannaanuaanaaanaanuaanuannd 39 KPC 1550 User s Manual Figures xi cms 16 PIQUE 2 IOS VEW ce 17 Figure 3 Mechanical Dimensions a naiaaaaaaaaaaaaaaaaaaanaanaanaanannannanuannannannannannnnannan 18 Figure 4 Connecting the display cable anaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaauaaaaaaaaaaaaa 19 Figure 5 Connecting USB mouse amp keyboard aaaaaaaaaaaaaaaaaasaaaaannaanaaauaanaanaanaa 20 Figure 6 Network cable with RJ45 connectOr aiaaizaaaaaaaaaaaaaaasaanaasaanaanaananuanuan 20 Figure 7 Turing on the System ainaaaaaaaaaanaananaanaanuannanannannannannannannannannnnnnnannan 21 Figure 8 VESA Mounting Hole Locations aiaaaaaaaaaaaaaaaaaaaaaaaaaaaaanaanaaaaaaaaanaanaa 22 Figure 9 Panel Mount Cut Out Hole and Maximum Panel Thickness 23 Figure l Panel WOUITING exec on cox ori Ge Goel etie atu E uoa ce su bote Ebro Eon Eben bor a 24 Table 1 KPC 1550 product specificatiIonS aiaaaaaaaaiaasaaannanaanaanuannaanaanuannannaanaa 14 T
5. Date Ediedby Changs 3 2011 11 23 Update Dimensions EL Quanmoax KPC 1550 User s Manual II Content COD IR E BAP ETN MEE RMT LMS Cae RUP EM STA RUPE RMU S NUDE EEN USE a s RTE ate 3 meri 4 RESET T M 4 Sale MASI CUO MS sone becas aoc be uten ubodter o bad Dexter dedu den Dec uec Dodo er DrcR dec Decade d eios 5 sisi YOUIB EOIN T EET 5 When Working Inside a Computer 1 112 211 2 va tta Sl Ka laa g sj d d kie 6 Preventing Electrostatic Discharge aaaaaaaaaaaaaaaaaasaasaanaanannanuan 6 Instructions Tor Lithium Batley e 7 Voltage FUN S vo tect ARR 7 BIET E E E EE E E E E A E A EEEE 8 FOW 10 WISE TNS Gude rasne sr cob n beoe areas 8 IMD ACKING eT DOTT 8 Regulatory Compliance Statements aaaaaaaaasaaaaaaa saasaasaasnaanaa 8 warani VEON 5 39 39 0 tS enint dexi inant k _ x Divos R P 9 Maintaining Your Computer inaanazaaaaaaaaaaaaaaaaaaaaanaaauaanaaanaaanaaanaa 10 Chapter NM OGUCUON RR ev vei bvosieuslu t adievs tut edv dev tiedus 13 SYRIAE T 13 OVSIOFTI TOME cones or trs metum eqs ms dM DIEM mM IEEE EE IUE 16 Mecnanica DIMENSIONS vsi at psc ue ouead ia obU eue UE SOLES a 18 Chapter 2 Geni Staite ns bal r 19 Se Hing p VOUL PC ova 19 Turning on the System udara saran a al nennen nnns 21 VE SA MOUNINO TEE 22 Panel MoUNUN arpassa aba bk Gina a 23
6. mm KPC 1550 Dimension 410 x 315 x 82 5 mm W x H x D Figure 3 Mechanical Dimensions of KPC 1550 KPC 1550 User s Manual 18 287 mm Chapter 2 Chapter 2 Getting Started B Setting up your PC m Connect the monitor mouse and keyboard Connecting the monitor Connect the appropriate cable from your display to the VGA DVI D HDMI port HDMI DVI D D PP e FF JI g B Figure 4 Connecting the display cable NOTE When the system reboots without connecting the VGA DVI D HDMI there S might be no image on screen when you insert these cables Please pressing lt Ctrl gt lt Alt gt lt F4 gt simultaneously to show the image on screen KPC 1550 User s Manual 19 Chapter 2 Connecting USB mouse amp keyboard Your KPC 1550 does not come with a keyboard and mouse connector but you can use any USB keyboard or mouse with your computer 4 USB on the bottom Figure 5 Connecting USB mouse amp keyboard NOTE Using a third party USB mouse or keyboard may require software drivers K Check the manufacturer s website for the latest software drivers B Connecting to a network device Connect one end of a network cable to the LAN port on the system rear panel and the other end to a hub or switch Figure 6 Network cable with RJ45 connector KPC 1550 User s Manual 20 poe i E Chapter 2 Turning on the system Connect the power adapter cable to the DC jack DC IN of the KPC 1550 Connect t
7. provide a level of protection proportional with the cost of the device Surge protectors prevent voltage spikes from entering a system through the AC power cord Surge protectors however do not offer protection against brownouts which occur when the voltage drops more than 20 percent below the normal AC line voltage level Line Conditioner Line conditioners go beyond the overvoltage protection of surge protectors KPC 1550 User s Manual 11 Line conditioners keep a system s AC power source voltage at a fairly constant level and therefore can handle brownouts Because of this added protection line conditioners cost more than surge protectors However line conditioners cannot protect against a complete loss of power B Uninterruptible Power Supply Uninterruptible power supply UPS systems offer the most complete protection against variations on power because they use battery power to keep the server running when AC power is lost The battery is charged by the AC power while it is available so when AC power is lost the battery can provide power to the system for a limited amount of time depending on the UPS system UPS systems range in price from a few hundred dollars to several thousand dollars with the more expensive unit s allowing you to run larger systems for a longer period of time when AC power is lost UPS systems that provide only 5 minutes of battery power let you conduct an orderly shutdown of the system but are not in
8. C 111 F 90 C 194 F 95 C 203 F CPU Fan Speed 7105 RPM SYS Fan Speed N A Select Screen 1 176 V Select Item 3 408 V Change Option 5 130 V F1 General Help 11 868 V F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc CPU Warning Temperature Options Disabled 80 C 176 F 85 C 185 F 90 C 194 F 95 C 203 F CPU Shutdown Temperature Options Disabled 80 C 176 F 85 C 185 F 90 C 194 F 95 C 203 F KPC 1550 User s Manual 31 Boot Menu Table 9 Boot Menu Advanced Boot Chipset Power Security Boot Settings Allows BIOS to Skip certain tests while booting This will Quick Boot Enabled decrease the time needed Full Screen Logo Display Disabled to boot the system Bootup Num Lock ON Wait For F1 If Error Enabled Hit DEL Message Display Enabled Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc Quick Boot Enabling this item allows BIOS to skip some Power On Self Tests POST while booting to decrease the time needed to boot the system When set to Disabled BIOS performs all the POST items Options Disabled Enabled Full Screen LOGO Display Options Disabled Enabled Bootup Num Lock On Allow you to select the power on state for the NumLock Options Off On Wait for FT If Error Enable
9. Disabled Enabled Resume By PCI E Device KPC 1550 User s Manual 35 Options Disabled Enabled Resume On RTC Alarm Options Disabled Enabled B Security Menu Table 13 Security Menu Advanced Chipset Power Security Security Setting Install or Change the password Supervisor Password Not Installed User Password Not Installed Change Supervisor Password Select Screen Change User Password Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc Change Supervisor Password Select this item to set or change the supervisor password The Supervisor Password item on top of the screen displays the default Not Installed After you have set a password this item displays Installed Change User Password Select this item to set or change the user password The User Password item on top of the screen displays the default Not Installed After you have set a password this item displays Installed KPC 1550 User s Manual 36 B Exit Menu Table 14 Exit Menu Advanced Chipset Power Security Exit Setting Exit System Setup after saving the changes Save Changes and Exit Discard Changes and Exit Discard Changes F10 key can be used for this Load Optimal Defaults operation Load Failsafe Defaults Select Screen Select Item Enter Go To Sub Screen F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006
10. Exit gt System Information ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc Table 3 IDE Device Setting Menu BIOS SETUP UTILITY Disable Disables LBA Mode SATA 1 Auto Enables LBA Mode if the device supports it and the device is not already formatted with LBA Mode disabled Device Not Detected LBA Large Mode DMA Mode Select Screen S M A R T 1 Select Item Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc KPC 1550 User s Manual 26 LBA Large Mode Enables or disables the LBA Logical Block Addressing Large mode Setting to Auto enables the LBA mode if the device supports this mode and if the device was not previously formatted with LBA mode disabled Options Disabled Auto DMA Mode Options Auto only S M A R T SMART stands for Smart Monitoring Analysis and Reporting Technology It allows AMIBIOS to use the SMART protocol to report server system information over a network Options Auto Disabled Enabled Table 4 System Information AMIBIOS Version 2 41 Build Date 12 20 10 Processor Select Screen Genuine Intel amp CPU 5 5 2 00 GHz Select Item Speed 2000MHz F1 General Help F10 Save and Exit Physical Memory ESC Exit Size 1024MB Sped 667MHz V02 67 C Copyright 1985 2006 American Megatrends Inc KPC 1550 User s Manual 27 B Advanced Menu Table 5
11. KPC 1550 15 Industrial Panel PC with Intel GM45 ICH9 M User s Guide KPC 1550 User s Manual I Contact Info Quanmax Inc 5F No 415 Ti Ding Blvd Sec 2 NeiHu District Taipei Taiwan 114 Tel 886 2 2799 2789 Fax 4886 2 2799 7399 Visit our site at WWW quanmax com 2010 Quanmax Inc All rights reserved The information in this user s guide is provided for reference only Quanmax does not assume any liability arising out of the application or use of the information or products described herein This user s guide may contain or reference information and products protected by copyrights or patents and does not convey any license under the patent rights of Quanmax nor the rights of others Quanmax is a registered trademark of Quanmax All trademarks registered trademarks and trade names used in this user s guide are the property of their respective owners All rights reserved This user s guide contains information proprietary to Quanmax Customers may reprint and use this user s guide in other publications Customers may alter this user s guide and publish it only after they remove the Quanmax name cover and logo Quanmax reserves the right to make changes without notice in product or component design as warranted by evolution in user needs or progress in engineering or manufacturing technology Changes which affect the operation of the unit will be documented in the next revision of this user s guide Revision
12. able 2 BIOS Maitt Menuiserie inet a a a ie awstats ah linet bobo dad dtes 26 Table 3 IDE Device Setting Mel ook a R nnn 26 Table System o TO OLI do ecesosi bs vitu v IPU SM VEPUV DS VIUS MPO TS UUVRDDEIGS VI NESE V vs DUI D VIDI N 27 Table 5 Advanced Menu aaanaanaaaaaaaaaaaaasasaananasannananannnnanannnnanannnnanannnnnnanannnnananannana 28 Table 6 Onboard Peripherals Configuration Settings sssse 29 Table 7 On Chip ATA Configuration a naaiaaaaaaaaaaaaaanaaanaaanaanuaanuannaaanaaanannuannaaanaa 30 Table 8 Hardware Health Configuration aaaaaiaaaaaaaaaaaaaaaaaanaaanaaanaaanaaauannaaanaa 31 Table 9 OE MENU NT mE 32 Tablet OG MPSCE WG MU TET ETT 33 Table Ti Video FUNCTION GOMMGUMION sov r a aV Va a UN VO pO r M PDA De EUR 34 Tables eis TT 35 Hle ele AMI ESTE TM 36 TaD TAEKE NENU UT 37 KPC 1550 User s Manual 4 Safety Instructions B Before You Begin Before handling the product read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety Refer to the Advisories section in the Preface for advisory conventions used in this user s guide including the distinction between Warnings Cautions Important Notes and Notes B Always use caution when handling operating a computer Only qualified experienced authorized electronics service personnel should access the
13. carton do not remove the components antistatic packing material until you are ready to install KPC 1550 User s Manual 6 the component in a computer Just before unwrapping the antistatic packaging be sure you are at an ESD workstation or grounded This will discharge any Static electricity that may have built up in your body B When transporting a sensitive component first place it in an antistatic container or packaging B Handle all sensitive components at an ESD workstation If possible use antistatic floor pads and workbench pads B Handle components and boards with care Don t touch the components or contacts on a board Hold a board by its edges or by its metal mounting bracket B Do not handle or store system boards near strong electrostatic electromagnetic magnetic or radioactive fields B instructions for Lithium Battery A WARNING Danger of explosion when battery is replaced with incorrect type Only replace with the same or equivalent type recommended by the manufacturer Do not dispose of lithium batteries in domestic waste Dispose of the battery according to the local regulations dealing with the disposal of these special materials e g to the collecting points for disposal of batteries B Voltage Ratings The external power adaptor of the KPC 1550 has the following voltage ratings fe KPC 1550 100 240Vac 10 12V 6 7A 80W or 100 240Vac 10 24V 3 75A 90W KPC 1550 User s Manual 7 Preface B H
14. d When set to Enabled the system waits for F1 key to be pressed when error occurs Options Disabled Enabled Hit DEL Message Display Enabled When set to Enabled the system displays the message Press DEL to run Setup during POST Options Disabled Enabled KPC 1550 User s Manual 32 B Chipset Menu Table 10 Chipset Menu Advanced Chipset Power Security Chipset Settings Select which graphics controller to use as the primary boot device Boots Graphic Adapter Priority IGD Internal Graphics Mode Select Enabled 8MB Video Function Configuration Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc Boots Graphic Adapter Priority Options IGD PCI IGD PCI PEG PEG IGD PEG PCI Internal Graphics Mode Select select the amount of system memory used by the Internal graphics device Options Disabled Enabled 32MB Enabled 64M Enabled 128M KPC 1550 User s Manual 33 Table 11 Video Function Configuration Advanced Chipset Power Security Video Function Configuration Options DVMT Mode Select DVMT Mode DVMT FIXED memory 256MB DVMT Mode Boot Display Device CRT LVDS Select Screen Panel Type 1024x768 18Bi 1 Select Item Panel BackLight Voltage V 2 5 Change Option F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc DVMT Mod
15. e Select Options DVMT Mode only DVMT FIXED Memory Options 128MB 256MB Maximum DVMT Boot Display Device Options CRT DVI CRT DVI LVDS CRT LVDS Panel Type Options 1024x768 24Bit 1CH Panel BackLight Voltage V Options 0 0 1 0 1 5 2 0 2 5 3 0 3 5 4 0 4 5 5 0 KPC 1550 User s Manual 34 Power Menu Table 12 Power Menu Advanced Chipset Power Security Power Management Settings Enable Disable ACPI support for Operating System ACPI Function Enabled Suspend mode S3 STR ENABLE If OS supports ACPI Repost Video on S3 Resume No Restore on AC Power Loss Power Off DISABLE If OS does not Resume By PS 2 KB MS from S3 Disabled support ACPI Resume from S3 By USB Device Disabled Resume By PCI E Device Disabled Change Option Resume On RTC Alarm Disabled F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc ACPI Function Enable Disable ACPI support for Operating System ENABLE If OS supports ACPI DISABLE IF OS Does not support ACPI Suspend mode Options S1 POS S3 STR Repost Video on S3 Resume Determines whether to invoke VGA BIOS post on S3 STR resume Options No Yes Restore on AC Power Loss Options Power OFF Power ON Last State Resume By PS 2 KB MS from S3 Options Disabled Enabled Resume From S3 By USB Device Options Disabled Enabled Resume On Ring Options Disabled Enabled Resume By PME Options
16. e hard disk drive Humidity High humidity can cause moisture to enter and accumulate in the system This moisture can cause corrosion of internal components and degrade such properties as electrical resistance and thermal conductivity Extreme moisture buildup inside the system can result in electrical shorts which can cause serious damage to the system Buildings in which climate is controlled usually maintain an acceptable level of humidity for system equipment However if a system is located in an unusually humid location a dehumidifier can be used to maintain the humidity within an acceptable range Refer to the Specifications section of this user s guide for the operating and storage humidity specifications Altitude Operating a system at a high altitude low pressure reduces the efficiency of the cooling fans to cool the system This can cause electrical problems related to arcing and corona effects This condition can also cause sealed components with internal pressure such as electrolytic capacitors to fail or perform at reduced efficiency Power Protection The greatest threats to a system s supply of power are power loss power spikes and power surges caused by electrical storms which interrupt system operation and or damage system components To protect your system always properly ground power cables and one of the following devices Surge Protector Surge protectors are available in a variety of types and usually
17. ement products If Quanmax repairs or replaces a product its warranty term is not extended Shipments not in compliance with this Limited Warranty Return Policy will not be accepted by Quanmax Limitation of Liability In no event shall Quanmax be liable for any defect in hardware software loss or inadequacy of data of any kind or for any direct indirect incidental or consequential damages in connection with or arising out of the performance or use of any product furnished hereunder Quanmax s liability shall in no event exceed the purchase price of the product purchased hereunder The foregoing limitation of liability shall be equally applicable to any service provided by Quanmax or its authorized agent B Maintaining Your Computer Environmental Factors B Temperature The ambient temperature within an enclosure may be greater than room ambient temperature Installation in an enclosure should be such that the amount of air flow required for safe operation is not compromised Consideration should be given to the maximum rated ambient temperature Overheating can cause a variety of problems including premature aging and failure of chips or mechanical failure of devices If the system has been exposed to abnormally cold temperatures allow a two hour warm up period to bring it up to normal operating temperature before KPC 1550 User s Manual 10 turning it on Failure to do so may cause damage to internal components particularly th
18. fault values for each of the parameters on the Setup menus which will provide the most stable performance settings The F8 key can be used for this operation KPC 1550 User s Manual 38 Chapter 4 Driver Installation If your KPC 1550 does not come with an operating system pre installed you will need to install an operating system and the necessary drivers to operate it After you have finished assembling your system and connected the appropriate power source power it up using the power supply and install the desired operating system You can download the drivers for the KPC 1550 from the Quanmax website at www quanmax com and install as instructed there For other operating systems please contact Quanmax KPC 1550 User s Manual 39
19. he BIOS manual specific to your product please contact Quanmax AMI s ROM BIOS provides a built in Setup program which allows the user to modify the basic system configuration and hardware parameters The modified data will be stored in a battery backed CMOS so that data will be retained even when the power is turned off In general the information saved in the CMOS RAM will not need to be changed unless there is a configuration change in the system such as a hard drive replacement or when a device is added It is possible for the CMOS battery to fail which will cause data loss in the CMOS only If this happens you will need to reconfigure your BIOS settings KPC 1550 User s Manual 25 B Main Menu The BIOS Setup is accessed by pressing the DEL key after the Power On Self Test POST memory test begins and before the operating system boot begins Once you enter the BIOS Setup Utility the Main Menu will appear on the screen The Main Menu provides System Overview information and allows you to set the System Time and Date Use the lt and gt cursor keys to navigate between menu screens Table 2 BIOS Main Menu BIOS SETUP UTILITY Advanced Chipset Power Security System Date Thu 012 23 2010 System Time 14 05 06 Select Screen gt SATA 1 Not Detected gt SATA 2 Not Detected 1 Select Item gt SATA 3 Not Detected Change Field gt CF Not Detected Tab Select Field F1 General Help F10 Save and
20. he power cable to the power adapter Connect the power cable to a power outlet Press the power switch on the front panel to turn on the system er bop HH Figure 7 Turing on the system KPC 1550 User s Manual 21 Chapter 2 B VESA Mounting The product comes with VESA FDMI 75 100 standard mounting holes as shown below Use 4 screws with the appropriate length for your mounting bracket VESA Mount Completion Insert Antenna if needed Figure 8 VESA Mounting Hole Locations KPC 1550 KPC 1550 User s Manual 22 Chapter 2 B Panel Mounting The Panel PC can be panel mounted and comes with brackets and screws for this purpose The required cutout for panel mounting and maximum panel thickness is shown below Figure 9 Panel Mount Cut out hole and maximum panel thickness Panel Size 410 mm x 315 mm KPC 1550 User s Manual 23 B Below are the demonstrations of how to do panel mounting Step1 Tightening the screws as shown right Step2 Done Figure 10 Panel Mounting KPC 1550 User s Manual 24 Chapter 2 Chapter 3 AMI BIOS Setup B Overview This chapter provides a description of the AMI BIOS The BIOS setup menus and available selections may vary from those of your product For specific information on the BIOS for your product please contact Quanmax NOTE The BIOS menus and selections for your product may vary from S those in this chapter For t
21. interior of a computer The power supplies produce high voltages and energy hazards which can cause bodily harm B Use extreme caution when installing or removing components Refer to the installation instructions in this user s guide for precautions and procedures If you have any questions please contact Quanmax Post Sales Technical Support B Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken and access is through the use of a tool or lock and key or other means of security and is controlled by authority responsible for the location WARNING High voltages are present inside the chassis when the unit s power cord is plugged into an electrical outlet Turn off system power turn off the power supply and then disconnect the power cord from its source before removing the chassis cover Turning off the system power switch does not remove power to components KPC 1550 User s Manual 5 B When Working Inside a Computer Before taking covers off a computer perform the following steps 1 Turn off the computer and any peripherals 2 Disconnect the computer and peripherals from their power sources or subsystems to prevent electric shock or system board damage This does not apply when hot swapping parts 3 Follow the guidelines provided in Preventing Electrostatic Discharge on the followi
22. l 13 Product Specifications Dimensions KPC 1550 410 x 315 x 82 5 mm W x H x D Weight KPC 1550 Intel Core 2 Duo Processor T9400 6M Cache 2 53 GHz 1066 MHz FSB Intel Core 2 Duo Processor P8400 CPU 3M Cache 2 26 GHz 1066 MHz FSB Intel Celeron amp Processor 575 1M Cache 2 00 GHz 667 MHz FSB Chipset Intel GM45 ICH9 M 2 x DDR3 800 1066MHz SO DIMM Socket up to 8 GB 125 SATA HDD or 1 x SSD Aluminum front bezel amp SECC chassis 2x GbE RJ 45 4x USB 2 0 1x HDMI 1x DVI D 1x VGA 5x COMs with 5V 12V Power Selection 1x Power On Off Switch 1x Power Connector Line Out Line In Mic In 1xPCI Slot 1xMini PCle slot Display Type 127 15 LED Resolution XGA 1024x768 Brightness 350 cd m Touch Screen 5 wire Resistive Type Wireless LAN 802 11b g n optional Network 2x Gigabit Ethernet On board LAN KPC 1550 100 240Vact 10 12V 6 7A 80W or Power Unit 100 240Vac 10 24V 3 75A 90W KPC 1550 User s Manual 14 LCD Display Humidity 0 C to 60 C CF SSD 0 C to 50 C 2 5 HDD Storage 0 C to 85 C 10 85 rel hum non condensing Mounting VESA Panel Mount Certifications CE FCC Class A IP65 front bezel Table 1 KPC 1550 product specifications KPC 1550 User s Manual L5 E System Tour Refer to the figures below to identify the components of the system B Rear I Os Power Button PCI Slot LAN LAN VGA DVI D Power Input AUDIO HDMI
23. ng page 4 Disconnect any telephone or telecommunications lines from the computer In addition take note of these safety guidelines when appropriate B To help avoid possible damage to system boards wait five seconds after turning off the computer before removing a component removing a system board or disconnecting a peripheral device from the computer H When you disconnect a cable pull on its connector or on its strain relief loop not on the cable itself Some cables have a connector with locking tabs If you are disconnecting this type of cable press in on the locking tabs before disconnecting the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before connecting a cable make sure both connectors are correctly oriented and aligned CAUTION A Do not attempt to service the system yourself except as explained in this user s guide Follow installation and troubleshooting instructions closely B Preventing Electrostatic Discharge Static electricity can harm system boards Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components Quanmax strongly encourages you to follow proper ESD procedure which can include wrist straps and smocks when servicing equipment You can also take the following steps to prevent damage from electrostatic discharge ESD B When unpacking a static sensitive component from its shipping
24. o radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures H Reorient or relocate the receiving antenna B Increase the separation between the equipment and receiver B Connect the equipment to an outlet on a circuit different from that to which the receiver is connected B Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by Quanmax could void the user s authority to operate the equipment NOTE The assembler of a personal computer system may be required to test the system oh and or make necessary modifications if a system is found to cause harmful interference or to be noncompliant with the appropriate standards for its intended use B Warranty Policy Limited Warranty Quanmax Inc s detailed Limited Warranty policy can be found under Support at www quanmax com Please consult your distributor for warranty verification The limited warranty is void if the product has been subjected to alteration neglect misuse or abuse if any repairs have been attempted by anyone other than Quanmax or its authorized agent or if the failure is caused by accident acts of God or other causes beyond the control of Quanmax or the manufacturer Neglect misuse and abuse shall include any installation operation or maintenance of the product
25. other than in accordance with the user s guide No agent dealer distributor service company or other party is authorized to change modify or extend the terms of this Limited Warranty in any manner whatsoever Quanmax reserves the right to make changes or improvements in any product without incurring any obligation to similarly alter products previously purchased Return Procedure For any Limited Warranty return please contact Support at www quanmax com and login to obtain a Return Material Authorization RMA Number If you do not have an KPC 1550 User s Manual 9 account send an email to support quanmax com to apply for one All product s returned to Quanmax for service or credit must be accompanied by a Return Material Authorization RMA Number Freight on all returned items must be prepaid by the customer who is responsible for any loss or damage caused by common carrier in transit Returns for Warranty must include a Failure Report for each unit by serial number s as well as a copy of the original invoice showing the date of purchase To reduce risk of damage returns of product must be in a Quanmax shipping container If the original container has been lost or damaged new shipping containers may be obtained from Quanmax Customer Service at a nominal cost Quanmax owns all parts removed from repaired products Quanmax uses new and reconditioned parts made by various manufacturers in performing warranty repairs and building replac
26. ow to Use This Guide This guide is designed to be used as step by step instructions for installation and as a reference for operation troubleshooting and upgrades NOTE f Driver downloads and additional information are available under Downloads on EF al our web site www quanmax com B Unpacking When unpacking follow these steps 1 After opening the box save it and the packing material for possible future shipment 2 Remove all items from the box If any items listed on the purchase order are missing notity Quanmax customer service immediately 3 Inspect the product for damage If there is damage notify Quanmax customer service immediately Refer to Warranty Policy for the return procedure B Regulatory Compliance Statements This section provides the FCC compliance statement for Class A devices FCC Compliance Statement This equipment has been tested and found to comply with limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reason able protection against harmful interference in residential installations This equipment generates uses and can radiate radiofrequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause KPC 1550 User s Manual 8 interference t
27. r Enabled 8 USB Ports Onboard LAN2 Controller Enabled 10 USB Ports Onboard LAN OPTROM Disabled 12 USB Ports Onboard Mini PCIE Controller Enabled gt On Chip ATA Devices Select Screen Select Item Change Field F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc USB Functions Options Disabled 2 4 6 8 10 12 USB Ports Legacy USB Support Options Enabled Disabled Auto KPC 1550 User s Manual 29 Audio Controller Options Enabled Disabled Onboard LAN1 Controller Options Enabled Disabled Onboard LAN2 Controller Options Enabled Disabled Onboard LAN OPTROM Options Enabled Disabled Onboard Mini PCIE Controller Options Enabled Disabled Table 7 On Chip ATA Configuration BIOS SETUP UTILITY On Chip ATA Configuration SATA Configuration Enhanced Disabled Configure SATA as IDE Compatible Enhanced Select Screen Select Item Change Option F1 General Help F10 Save and Exit ESC Exit V02 67 C Copyright 1985 2006 American Megatrends Inc On Chip ATA Configuration Options Disabled Compatible Enhanced Configure SATA Options IDE AHCI KPC 1550 User s Manual 30 Table 8 Hardware Health Configuration BIOS SETUP UTILITY Hardware Health Configuration Options CPU Warning Temperature Disabled CPU Shutdown Temperature Disabled Disabled 80 C 176 F CPU Temperature 4290 105 F 85 C 185 F System Temperature 44
28. tended to provide continued operation Surge protectors should be used with all UPS systems and the UPS system should be Underwriters Laboratories UL safety approved KPC 1550 User s Manual 12 Chapter 1 Introduction B Overview The KPC 1550 Panel PC is supporting the latest Intel 45nm Core 2 Duo processor with the high integration of the Intel GM45 ICH9M chipset Featuring DDR3 SODIMM up to 8GB Intel GMA 4500MHD supports DirectX 10 and Shader Model 4 0 Storage includes a 2 5 SATA hard drive or a solid state drive SSD Supported interfaces include 2x GbE LAN HD audio 5x serial ports USB 2 0 ports VGA DVI D and HDMI thus easily meeting a broad range of customer requirements The KPC series provide a compact high performance human machine interface with optimal shock vibration and temperature resistance for tough industrial demands Checklist KPC 1550 Power Adapter Power Cord Driver CD Quick installation Guide Features 15 TFT LCD Display 15 TFT LCD Display with Resistive 5 wire TouchScreen CPU Support Intel Core 2 Duo Processor T9400 6M Cache 2 53 GHz 1066 MHz FSB Intel Core 2 Duo Processor P8400 3M Cache 2 26 GHz 1066 MHz FSB Intel Celeron Processor 575 1M Cache 2 00 GHz 667 MHz FSB Intel Graphics Media Accelerator 4500MHD supports IP65 approved front bezel 2x GbE 5x COMs 4x USB ports 1x PCI SLOT 1x Mini PCle slot VGA DVI D HDMI HD Audio KPC 1550 User s Manua
Download Pdf Manuals
Related Search