Home

2014 Nissan Maxima

1. lf your ear position is still higher than the recommended alignment place the head restraint headrest at the highest position If the head restraint headrest has been re moved ensure that it is reinstalled and locked in place before riding in that desig nated seating position Safety Seats seat belts and supplemental restraint system 1 11 t Cd l a LRS2074 Adjustable head restraint headrest Non adjustable head restraint Removal components headrest components Use the following procedure to remove the head 1 Removable head restraint headrest 1 Removable head restraint headrest restraints headrests 2 Multiple notches 2 Single Notch 1 Adjust the seat or seatback as necessary 3 Lock knobs 3 Lock knobs 2 Push and hold the lock knobs A Stalks 4 Stalks 3 Pull the head restraint headrest up until it is removed from the seat 4 Store the head restraint headrest properly so it is not loose in the vehicle 5 Reinstall the head restraint headrest and properly adjust the seat or seatback before an occupant uses the seating position 1 12 Safety Seats seat belts and supplemental restraint system Install 1 Align the head restraint headrest stalks with the holes in the seat Make sure the head restraint headrest is facing the correct di rection Push the head restraint headrest down until it locks in place For adjustable head restraint headrest Adjust the head restraint headrest so the cen
2. LDI0341 WDI0670 LDI2135 Step light Personal light Trunk light Use a cloth to protect the housing Use a cloth to protect the housing Maintenance and do it yourself 8 31 WHEELS AND TIRES If you have a flat tire see Flat tire in the In case of emergency section of this manual TIRE PRESSURE Tire Pressure Monitoring System TPMS This vehicle is equipped with the Tire Pressure Monitoring System TPMS It monitors tire pressure of all tires except the spare When the low tire pressure warning light is lit and the CHECK TIRE PRESSURE warning appears in the ve hicle information display one or more of your tires is significantly under inflated If equipped the system also displays pres sure of all tires except the spare tire on the display screen by sending a signal from a sensor that is installed in each wheel The TPMS will activate only when the vehicle is driven at speeds above 16 MPH 25 km h Also this system may not de tect a sudden drop in tire pressure for example a flat tire while driving 8 32 Maintenance and do it yourself For more details refer to Low tire pres sure warning light in the Instruments and controls section Tire pressure informa tion in the Monitor climate audio phone and voice recognition section Tire Pressure Monitoring System TPMS in the Starting and driving section and Flat tire in the In case of emergency
3. 1 15 Pregnant WOMEN s sesser deen reak erie Ow ew ed 1 18 mured Persons cee ees oe ec een eeead eee cee 1 18 Three point type seat belt with retractor 1 18 Seat belt extenders 0 ccc cece eee 1 21 Seat belt maintenance 0 e eee ee eee 1 22 CMG Sa cits cctateeidceieGadeseeateeee pacar aes 1 22 Manesse teed caneeo EETA A EERE E EEE 1 23 SES E E E E deecone 1 23 Larger children 6 caneseteeecaeeeeneaetneteces eas 1 23 Child restraints lt esecudawsiwce saeeeed acer te redre 1 24 Precautions on child restraints 04 LATCH Lower Anchors and Tethers for CHildren System 000 ccc ccc ees Rear facing child restraint installation using EAU Cine cca kgeuceeadean he dan oeecaes ends canes Rear facing child restraint installation using the seat belts s 02cusetasiaenas deewe we wee ous ee Forward facing child restraint installation USING LAI CH as suweayeaetess nd ven eei EAE Forward facing child restraint installation using the seat beltS cece eee eee Installing top tether strap 0 000 cee eee Booster SCalS cs cewua bowed bcheete shew ease ee Supplemental restraint system 0 cece eee Precautions on supplemental restraint SYSTEM teceeunne nee s een ee E He emeene es Supplemental air bag warning labels Supplemental air bag warning light SEATS Sit upright and well back AWARNING e Do not ride in a movi
4. AWARNING Do not use water or acidic cleaners hot steam cleaners on the seat This can dam age the seat or occupant classification sensor This can also affect the operation of the air bag system and result in serious personal injury A CAUTION Never use benzine thinner or any simi lar material Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly Do not use saddle soap car waxes polishes oils cleaning fluids solvents deter gents or ammonia based cleaners as they may damage the leather s natural finish Never use fabric protectors unless rec ommended by the manufacturer Do not use glass or plastic cleaner on meter or gauge lens covers It may dam age the lens cover AIR FRESHENERS Most air fresheners use a solvent that could affect the vehicle interior If you use an air freshener take the following precautions Hanging type air fresheners can cause per manent discoloration when they contact ve hicle interior surfaces Place the air fresh ener in a location that allows it to hang free and not contact an interior surface Liquid type air fresheners typically clip on the vents These products can cause imme diate damage and discoloration when spilled on interior surfaces Carefully read and follow the manufacturer s in structions before using the air fresheners FLOOR MATS AWARNING To avoid potential pedal interference tha
5. D Vehicle load limit See loading infor mation in the Technical and con sumer information section Original tire size The size of the tires originally installed on the vehicle at the factory 8 34 Maintenance and do it yourself FRONT AVANT P XXX XXR XX SPARE DE SECOURS EEN COLD TIRE PRESSURE PRESSION DES PNEUS A FROID XXX kPa XX psi XXX kPa XX psi XXX kPa XX psi SIZE DIMENSIONS P XXX XX A XX T XXX XX D XX SEE ORPNER S MANUAL FOR ADIA IORAL INFORMATION VOIR LE MABUEL DE L USAGER POUAP EUS DE REMSEIGWEMENTS Cold tire pressure Inflate the tires to this pressure when the tires are cold Tires are considered COLD after the vehicle has been parked for 3 or more hours or driven less than 1 mile 1 6 km at moderate speeds The recommended cold tire inflation is set by the manufacturer to provide the best balance of tire wear vehicle handling driveability tire noise etc up to the vehicle s GVWR Tire size refer to Tire labeling in this section Spare tire size if so equipped 4 Read the tire pressure on the gauge stem and compare to the specifica tion shown on the Tire and Loading Information label 5 Add air to the tire as needed If too much air is added press the core of the valve stem briefly with the tip of the gauge stem to release pressure Recheck the pressure and add or release air as needed 6 Install the valv
6. Ds Drive Sport When the shift lever is shifted from the D Drive position to the manual shift gate the transmission enters the Ds Drive Sport mode Moving the shift lever to the Ds Drive Sport position allows you to enjoy sporty driving shift operation on a winding road and feel smooth acceleration or deceleration on a hilly road by moving in a lower gear automatically When canceling the Ds mode return the shift lever to the D Drive posi tion The transmission returns to the normal driv ing mode Manual shift mode When the shift lever is in the Ds Drive Sport position the transmission is ready for the manual shift mode Shift ranges can be selected manu ally by moving the shift lever up or down or pulling the right side or left side paddle shifter To cancel the Ds mode return shift lever to the D Drive position The transmission returns to au tomatic driving mode Starting and driving 5 15 When the shift lever is shifted from D Drive to the manual shift gate with the vehicle stopped or while driving the transmission enters the manual shift mode Shift ranges can be selected manually Shift ranges can also be selected using the shift paddles if so equipped on the steering wheel and In the manual shift mode the shift range is displayed on the position indicator in the meter When shifting the shift lever to the manual shift gate the position indicator displays 1 first up to 6
7. 0 0 cece eee ee eee 9 25 Readiness for inspection maintenance I M test 9 26 Event Data Recorders EDR 00cceeeeaues 9 96 Owner s Manual Service Manual order information 9 27 CAPACITIES AND RECOMMENDED FUEL LUBRICANTS The following are approximate capacities The actual refill capacities may be slightly different When refilling follow the procedure described in the Maintenance and do it yourself section to determine the proper refill capacity Capacity Approximate US measure Imp measure Fuel 20 gal 16 5 8 gal Engine oil 7 Drain and Refill With oil filter change 5 1 8 qt 4 1 4 qt Without oil filter change 4 3 4 qt 4 qt Cooling system With reservoir 2 3 8 gal 2 gal Liter 75 6 4 8 4 5 9 0 CVT fluid See a NISSAN dealer for service Power steering fluid PSF Refill to the proper level according to the instructions in Brake fluid the Maintenance and do it yourself section Multi purpose grease Air conditioning system refrigerant Air conditioning system oil Windshield washer fluid 1 72 3 A oe 6 ua 8 9 1 1 4 gal 1 gal For further details see Fuel recommendation in this section For further details see Engine oil and oil filter recommendation in this section 4 5 NISSAN recommends Genuine NISSAN Ester Engine Oil available at a NISSAN dealer Use only Genuine NISSAN CVT Fluid NS 2 Using transmission fluid other than Genui
8. 4 Air cleaner P 8 19 5 Fuse block P 8 22 6 Battery P 8 15 7 Fuse fusible link box P 8 22 8 Engine oil dipstick P 8 10 9 Radiator cap P 8 8 10 Drive belt location P 8 1 7 11 Engine coolant reservoir P 8 8 12 Windshield washer fluid reservoir P 8 14 NOTE Side covers removed for clarity See the page number indicated in paren theses for operating details WARNING INDICATOR LIGHTS Anti lock Braking System ABS warn ing light Brake warning light Low tire pressure warning light Continuously Vari able Transmission CVT indicator light Continuously Vari able Transmission CVT position indi cator light Front passenger air bag status light Security indicator light Side light and head light indicator light green Slip indicator light Turn signal hazard indicator lights Vehicle Dynamic Control OFF indica tor light Illustrated table of contents 0 9 MEMO 0 10 Illustrated table of contents 1 Safety Seats seat belts and supplemental restraint system Seale viutinwtuee users E eee kaye eunesabaaweuned 1 2 Front power seat adjustment 0006 1 3 Folding rear seat if so equipped n nanana 1 5 Front seat head restraints headrests 1 7 Rear seat head restraints headrests 1 11 Sde caa e gaac cee aescesen boone eee ceneesen E 1 15 Precautions on seat belt usage
9. BRAKES If the brakes do not operate properly have the brakes checked by a NISSAN dealer Self adjusting brakes Your vehicle is equipped with self adjusting brakes The front and rear disc type brakes self adjust every time the brake pedal is applied AWARNING See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators When a brake pad requires re placement a high pitched scraping or screech ing sound will be heard when the vehicle is in motion The noise will be heard whether or not the brake pedal is depressed Have the brakes checked as soon as possible if the wear indicator sound is heard Under some driving or climate conditions occa sional brake squeak squeal or other noise may be heard Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system Proper brake inspection intervals should be followed For more information regarding brake inspections see the appropriate mainte nance schedule information in the NISSAN Ser vice and Maintenance Guide Maintenance and do it yourself 8 21 FUSES Two types of fuses are used Type is used in the fuse boxes in the engine compartment Type is used in the passenger compartment fuse box Type A fuses are provided as spare fuses They are stored i
10. Every person who drives or rides in this vehicle should use a seat belt at all times Children should be properly re strained in the rear seat and if appro priate in a child restraint 1 16 Safety Seats seat belts and supplemental restraint system AWARNING The seat belt should be properly ad justed to a snug fit Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an acci dent Serious injury or death can occur if the seat belt is not worn properly AWARNING Always route the shoulder belt over your shoulder and across your chest Never put the belt behind your back under your arm or across your neck The belt should be away from your face and neck but not falling off your shoulder Position the lap belt as low and snug as possible AROUND THE HIPS NOT THE WAIST A lap belt worn too high could increase the risk of internal injuries in an accident Be sure the seat belt tongue is securely fastened to the proper buckle Do not wear the seat belt inside out or twisted Doing so may reduce its effectiveness Do not allow more than one person to use the same seat belt Never carry more people in the vehicle than there are seat belts If the seat belt warning light glows con tinuously while the ignition is placed in the ON position with all doors closed and all seat belts fastened it may indi cate a malfunction in the system
11. Example 1 800 662 6200 One eight zero zero The system repeats the numbers and prompts you to enter more six six two The system repeats the numbers and prompts you to enter more six two zero zero ea Say pound for Say star for avail able when using the Special Number com mand and the Send command during a call See List of voice commands and Special number in this section for more information Example 1 555 1212 123 One five five five one two one two star one two three Say plus for available only when using the Special Number command Say pause for a 2 second pause available only when storing a phone book number NOTE For best results say phone numbers as single digits The voice command Help is available at any time Please use the Help command to get information on how to use the system Voice Prompt Interrupt In most cases you can interrupt the voice feed back to speak the next command by pressing the fi button on the steering wheel After interrupting the system wait for a beep before speaking your command One Shot Call To use the system faster you may speak the second level commands with the main menu command on the main menu For example press the fi button and after the tone say Call Redial Monitor climate audio phone and voic
12. 27 kg 135 kg Occupants R FA 150 Ib x 2 300 Iib 30 lb x 2 60 Ib 70 kg 135 kg 14 kg Luggage Pr 30 Ib x 2 60 Ib 14 kg 27 kg Occupants Lk 150 Ib x 2 300 Ib 70 kg 135 kg Occupants Luggage RERRK CEECEE 150 Ib x 5 750 Ib 30 Ib x 5 150 b 70 kg 340 kg 14 kg 70 kg Example 9 14 Technical and consumer information Remaining available cargo and luggage load capacity 740 Ib 336 kg Remaining available cargo and luggage load capacity 1 040 Ib 472 kg Remaining available cargo and luggage load capacity 500 Ib 227 kg LT10152 Steps for determining correct load limit 1 Locate the statement The combined weight of occupants and cargo should never exceed XXX Ibs or XXX kg on your vehicle s placard 2 Determine the combined weight of the driver and passengers that will be riding in your vehicle 3 Subtract the combined weight of the driver and passengers from XXX lbs or XXX kg 4 The resulting figure equals the avail able amount of cargo and luggage load capacity For example if the XXX amount equals 1 400 lbs and there will be five 150 Ib passengers in your vehicle the amount of avail able cargo and luggage load capac ity is 650 Ibs 1 400 750 5 X 150 650 Ibs or 640 340 5 X 70 300 kg 5 Determine the combined weight of luggage and cargo being loaded on the vehicle That weight may not safely exce
13. A CAUTION To avoid discharging the vehicle battery use a phone after starting the engine 3 Bluetooth Ill microphone location Your NISSAN is equipped with the Bluetooth Hands Free Phone System If you have a com patible Bluetooth enabled cellular phone you can set up the wireless connection between your cellular phone and the in vehicle phone module With Bluetooth wireless technology you can 4 92 Monitor climate audio phone and voice recognition systems make or receive a hands free telephone call with your cellular phone in the vehicle Once your cellular phone is connected to the in vehicle phone module no other phone con necting procedure is required Your phone is automatically connected with the in vehicle phone module when the ignition switch is placed in the ON position with the previously connected cellular phone turned on and carried in the ve hicle You can connect up to 5 different Bluetooth cellular phones to the in vehicle phone module However you can talk on only one cellular phone at a time Before using the Bluetooth Hands Free Phone System refer to the following notes Set up the wireless connection between a compatible cellular phone and the in vehicle phone module before using the hands free phone system Some Bluetooth enabled cellular phones may not be recognized by the in vehicle phone module Please visit www nissanusa com bluetooth for a recom mended
14. CVT Continuously Variable Transmission CVT indicator light When the ignition switch is placed in the ON position the light comes on for 2 seconds oF Continuously Variable Transmission CVT position indicator light When the ignition switch is placed in the ON position the indicator light shows the shift lever position See Driving the vehicle in the Starting and driving section of this manual CRUISE Cruise main switch indicator light The light comes on when the cruise control main switch is pushed The light goes out when the main switch is pushed again When the cruise main switch indicator light comes on the cruise control system is operational Front fog light indicator light if so equipped The front fog light indicator light illuminates when the front fog lights are ON See Fog light switch later in this section Se Front passenger air bag status OFF light The front passenger air bag status light will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used For front passenger air bag status light operation see Front passenger air bag and status light in the Safety Seats seat belts and supplemental restraint system section of this manual HO High beam indicator light blue This blue light comes on when the headlight high beams are on and goes out when the low beams are selected The high beam indic
15. Do not stop the engine 2 Turn off the air conditioner Open all the windows move the heater or air conditioner temperature control to maximum hot and fan control to high speed 3 Get out of the vehicle Look and listen for steam or coolant escaping from the radiator before opening the hood If steam or cool ant is escaping turn off the engine Do not open the hood further until no steam or coolant can be seen 4 Open the engine hood AWARNING If steam or water is coming from the engine stand clear to prevent getting burned 5 Visually check drive belts for damage or looseness Also check if the cooling fan is running The radiator hoses and radiator should not leak water If coolant is leaking the water pump belt is missing or loose or the cooling fan does not run stop the engine AWARNING Be careful not to allow your hands hair jewelry or clothing to come into contact with or get caught in engine belts or the engine cooling fan The engine cooling fan can start at any time 6 After the engine cools down check the cool ant level in the engine coolant reservoir tank with the engine running Add coolant to the engine coolant reservoir tank if necessary Have your vehicle repaired at a NISSAN dealer TOWING YOUR VEHICLE When towing your vehicle all State Provincial in Canada and local regulations for towing must be followed Incorrect towing equipment could dam age your vehicle Towing instr
16. FOREWORD Welcome to the growing family of new NISSAN owners This vehicle is delivered to you with confidence It was produced using the latest techniques and strict quality control This manual was prepared to help you under stand the operation and maintenance of your vehicle so that you may enjoy many miles kilome ters of driving pleasure Please read through this manual before operating your vehicle A separate Warranty Information Booklet explains details about the warranties cov ering your vehicle The NISSAN Service and Maintenance Guide explains details about maintaining and servicing your ve hicle Additionally a separate Customer Care Lemon Law Booklet U S only will explain how to resolve any concerns you may have with your vehicle as well as clarify your rights under your state s lemon law Your NISSAN dealership knows your vehicle best When you require any service or have any questions they will be glad to assist you with the extensive resources available to them In addition to factory installed options your ve hicle may also be equipped with additional ac cessories installed by NISSAN or by your NISSAN dealer prior to delivery It is important that you familiarize yourself with all disclosures warnings cautions and instructions concerning proper use of such accessories prior to operating the vehicle and or accessory See a NISSAN dealer for details concerning the particular ac cessories w
17. Press the button For information on voice adaptation see Voice adaptation VA mode in this section 4 The system announces the current language and gives you the option to change the lan guage to Spanish in Spanish or French in French To select the current language press the PHONE SEND fx button To select a different language tilt the tuning switch 4 or Y up or down NOTE You must press the 44 button within 5 seconds to change the language 5 If you decide not to change the language do not press either button After 5 seconds the VR session will end and the language will not be changed Connecting procedure NOTE The connecting procedure must be per formed when the vehicle is stationary If the vehicle starts moving during the procedure the procedure will be cancelled 1 Main Menu Connect phone A Add phone Initiate from handset Name phone Press the i button on the steering wheel The system announces the available commands Say Connect phone A The system ac knowledges the command and announces the next set of available commands Say Add phone The system acknowl edges the command and asks you to initiate connecting from the phone handset The connecting procedure of the cellular phone varies according to each cellular tions on connecting NISSAN recommended cellular phones When prompted for a Passk
18. To shut off the engine in an emergency situation while driving perform the following procedure Rapidly push the push button ignition switch 3 consecutive times in less than 1 5 seconds or Push and hold the push button ignition switch for more than 2 seconds 6 2 Incase of emergency HAZARD WARNING FLASHER SWITCH g LIC0394 Push the switch on to warn other drivers when you must stop or park under emergency condi tions All turn signal lights flash A WARNING If stopping for an emergency be sure to move the vehicle well off the road Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic Turn signals do not work when the haz ard warning flasher lights are on The flashers will operate with the ignition switch placed in any position Some state laws may prohibit the use of the hazard warning flasher switch while driving FLAT TIRE TIRE PRESSURE MONITORING SYSTEM TPMS This vehicle is equipped with the Tire Pressure Monitoring System TPMS It monitors tire pres sure of all tires except the spare When the low tire pressure warning light is lit and the CHECK TIRE PRESSURE warning appears in the vehicle information display one or more of your tires is significantly under inflated If the vehicle is being driven with low tire pressure the TPMS will acti v
19. aaao aaa 7 5 Fluid Brake fluid 0200 00 8 13 Capacities and recommended fuel lubricants 00000 Ge 9 2 Continuously Variable Transmission RCAC ee ht wk oe te a a 8 12 Engine coolant 4 04 o oo ee we aed 8 7 Engine oil a a m e ay oe eee ho es ee 8 10 Power steering fluid 8 13 Windshield washer fluid 8 14 F M V S S certification label 9 10 Fog light switch a dx se ee we eww GS 2 34 Folding rearseat 02 0004 1 6 Front air bag system See supplemental restraint system 1 50 Front seats 6 me oS ee Hw Se ee 1 2 Fuel Capacities and recommended fuel lubricantS 2 26266 eee eee es 9 2 Fuel economy 246i 44 8 baka amp OA 5 22 Fuel fillerdoorandcap 3 21 Fuel gauge saaa a od ad hE we AG 2 7 Fuel octane rating 2 9 4 Loose fuel cap warning 2 25 3 21 PUSeGe 242 ences Fe he ow ee eS oe 8 22 Fusible links sa as aaa 8 24 G Garage door opener HomeLink Universal TeNsCGWEr 4 244 cece heed Rees bea 2 54 Gas Cap isareti deca Gtesdea ds 3 21 Gauge Engine coolant temperature gauge 2 6 Puel gauges se scoa a uea oe ae E 2 7 Odometer sasa sama daonnan 2 5 Speedometer aoaaa aa 2 5 Tachometer sai ss 2 6 wre 4 0 hw ea Wn 2 6 Trip odometer eed we Ge me oe Ha 2 5 General maintenance 8 2 Glove DOK soe sw aawa we ee a a 2 42 Glove box lock anaoa 2 42 Grocery HOOKS gt s s moa Sedu eee
20. ae E we me Sowers Wee sie ES See 4 91 Car phone or CB radios j2 00 sw0ssekkedecdecesgeuends 4 91 Bluetooth Hands Free Phone System without Navigation System if so equipped 05 4 99 Regulatory Information 000 cee eee eee 4 93 Using the SVSteM 2c ctecsataceddedaavevenceene 4 94 CONUCVDUUONS ccocccpaedekoyeeeneeneneeeanwe 4 96 CeO Sta CG fet crac purcowar doe ce eer ores see 4 96 List Of voice COMMANGS 4 s2 02 460 seeweece eae we 4 98 Voice Adaptation VA mode 00 ee ee 4 102 Manual control 25025025000 f0eeee8eebee cs ninda 4 103 Troubleshooting guide 02 02000 4 105 Bluetooth Hands Free Phone System with Navigation System if so equipped 05 4 106 Regulatory Information 0000 eee eee 4 108 Voice commands rsrsrs Sted Rae tania Goede webs 4 108 Connecting procedure 0 cece eee ee eee 4 109 Vehicle Phonebook ccc eee eens 4 110 Handset phonebook cee cece eee 4 112 Making a cal secaseusetienepee eden sedan R 4 113 Receiving a Call couechecesdeaedneewes eects edad 4 114 DUNG A Cdliliacauseesegsuss reaper e 4 115 Endam aCA esre era bao ceence cee Beene este 4 115 Phone Settings 4462s244ebotedeGetooeeenanye sd 4 116 Bluetooth settings lt a2 2c00005 oreckacennndiex 4 117 CAN VOUE dcaneauinandaectane REEE EENEN ESRT 4 118 NISSAN Voice Recognition System Of 20 SOUDOEO ta euecsiew E EE 4 119 NISSAN Voice Recognition Sta
21. or 1 included for your DVD entertainment system The region code A is displayed as a small sym bol printed on the top of the DVD This vehicle installed DVD player cannot play DVDs with a re gion code other than 1 or ALL Copyright and trademark The technology protected by the U S patent and other intellectual property rights owned by Macrovision Corporation and other right holders is adopted for this system e This copyright protected technology cannot be used without a permit from Macrovision Corporation It is limited to personal use etc as long as the permit from Macrovision Corporation is not issued Modifying or disassembling is prohib ited Dolby digital is manufactured under li cense from Dolby Laboratories Inc are trademarks of Dolby Laboratories Inc e DTS and DTS Digital Surround EE are registered trademarks of Digital Theater Systems Inc USB Universal Serial Bus memory if so equipped AWARNING Do not connect disconnect or operate the USB device while driving Doing so can be a distraction If distracted you could lose control of your vehicle and cause an acci dent or serious injury Monitor climate audio phone and voice recognition systems 4 39 A CAUTION e Do not force the USB device into the USB port Inserting the USB device tilted or up side down into the port may damage the port Make sure that the USB device is connect
22. section Tire inflation pressure Check the tire pressures including the spare often and always prior to long dis tance trips The recommended tire pres sure specifications are shown on the F M V S S C M V S S certification label or the Tire and Loading Information label under the Cold Tire Pressure heading The Tire and Loading Information label is affixed to the driver side center pillar Tire pressures should be checked regularly because Most tires naturally lose air over time Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking The tire pressures should be checked when the tires are cold The tires are considered COLD after the vehicle has been parked for 3 or more hours or driven less than 1 mile 1 6 km at moderate speeds Set the tire pressure to the normal cold tire inflation pressure when the vehicle speed or load is reduced Incorrect tire pressure including un der inflation may adversely affect tire life and vehicle handling AWARNING Improperly inflated tires can fail suddenly and cause an accident The Gross Vehicle Weight Rating GVWR is located on the F M V S S C M V S S certifica tion label The vehicle weight ca pacity is indicated on the Tire and Loading Information label if so equipped Do not load your ve hicle beyond this capacity Over loading your vehicle may result in reduced tire life unsafe
23. 11 RPT RDM button 12 SCAN button 13 AM FM button 14 DISP CLOCK button FM AM RADIO WITH COMPACT DISC CD CHANGER if so equipped For all operation precautions see Audio opera tion precautions in this section Audio main operation VOL ON OFF control Place the ignition switch in the ACC or ON position and push the VOL ON OFF control knob while the system is off to call up the mode radio or CD that was playing immediately before the system was turned off To turn the system off press the VOL ON OFF control knob Turn the VOL ON OFF control knob to adjust the volume Monitor climate audio phone and voice recognition systems 4 51 Audio control knob e Adjusts the treble to the desired level Adjusts the balance to the desired level Balance adjusts the sound level between the left and right speakers Adjusts the fade to the desired level Fade adjusts the sound level between the front and rear speakers D Adjusts the bass to the desired level Speed Sensitive Vol Adjusts the speed sensitive volume function which increases the volume of the audio system as the speed of the vehicle increases Set to OFF to disable the feature The higher the setting the more the volume increases in relation to vehicle speed Bass treble balance and fade can also be adjusted by pressing the AUDIO control knob and turning it to select the item to adjust When the desired item is shown on the display turn the
24. 4 Hand the Intelligent Key to the valet and keep the mechanical key with you See Trunk lid in this section Storage in the Instruments and controls section and Seats in the Safety seats seat belts and supplemental restraint system section of this manual NISSAN VEHICLE IMMOBILIZER SYSTEM KEYS You can only drive your vehicle using the master keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle These keys have a transponder chip in the key head The master key can be used for all the locks To protect belongings when you leave a key with someone give them the Intelligent Key only not the mechanical key Never leave these keys in the vehicle Additional or replacement keys If you still have a key the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys Your dealer can dupli cate your existing key As many as four NISSAN Vehicle Immobilizer System keys can be used with one vehicle You should bring all NISSAN Vehicle Immobilizer System keys that you have to your NISSAN dealer for registration This is be cause the registration process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System After the registration process these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System during registration Pre driving checks and adjustment
25. 5 18 Starting and driving MIL in the Instrument and controls sec tion This will occur even if all electrical circuits are functioning properly In this case place the ignition switch in the OFF position and wait for 10 seconds Then push the switch back to the ON position The vehicle should return to its normal op erating condition If it does not return to its normal operating condition have a NISSAN dealer check the transmission and repair if necessary AWARNING When the high fluid temperature protec tion mode or fail safe operation occurs vehicle speed may be gradually reduced The reduced speed may be lower than other traffic which could increase the chance of a collision Be especially careful when driving If necessary pull to the side of the road at a safe place and allow the transmission to return to normal opera tion or have it repaired if necessary PARKING BRAKE AWARNING Be sure the parking brake is fully re leased before driving Failure to do so can cause brake failure and lead to an accident Do not release the parking brake from outside the vehicle Do not use the shift lever in place of the parking brake When parking be sure the parking brake is fully engaged Do not leave children unattended in a vehicle They could release the parking brake and cause an accident To engage Firmly depress the parking brake To release i 2 3 Firmly apply the foot brake Move th
26. Be sure to remove any old gasket material remaining on the sealing surface of the engine Failure to do so could lead to engine damage 6 Coat the gasket on the new filter with clean engine oll 7 Screw on the oil filter until a slight resistance is felt then tighten an additional 2 3 turn 8 Start the engine and check for leakage around the oil filter Correct as required 9 Turn the engine off and wait more than 10 minutes Check the oil level Add engine oil if necessary CONTINUOUSLY VARIABLE TRANSMISSION CVT FLUID A CAUTION Use only Genuine NISSAN CVT Fluid NS 2 Do not mix with other fluids Using transmission fluid other than Genuine NISSAN CVT Fluid NS 2 will damage the CVT which is not covered by the warranty When checking or replacement of CVT fluid is required we recommend your NISSAN dealer for Servicing POWER STEERING FLUID The fluid level should be checked using the HOT MAX range on the power steering fluid reservoir at fluid temperatures of 122 176 F 50 80 C or using the COLD MAX range on the power steering fluid reservoir at fluid tempera tures of 32 86 F 0 30 C If the fluid is at or below the MIN line add Genu ine NISSAN PSF to HOT MAX or COLD MAX depending on system fluid temperature Remove the cap and fill through the opening A CAUTION e DO NOT OVERFILL e Recommended fluid is NISSAN PSF or equivalent Genuine BRAKE FLUID For furt
27. Before inserting or disconnecting a ignition switch is in the ACC or ON position plug be sure the electrical accessory being used is turned OFF Push the plug in as far as it will go If good contact is not made the plug may overheat or the internal temperature fuse may open When not in use be sure to close the cap Do not allow water or any other liquid to contact the outlet LIC1392 Front center console The power outlets are for powering electrical accessories such as cellular telephones They are rated at 12 Volt 120 W 10A maximum 2 38 Instruments and controls A CAUTION e Do not use for anything other than O00 000 sunglasses e Do not leave sunglasses in the sun glasses holder while parking in direct sunlight The heat may damage the sunglasses LICO016 SEATBACK POCKETS SUNGLASSES HOLDER The seatback pockets are located on the back of To open the sunglasses holder push and release the driver s and passenger s seats The pockets can be used to store maps Only store one pair of sunglasses in the holder AWARNING Keep the sunglasses holder closed while driving to prevent an accident Instruments and controls 2 39 LIC 1395 Front CUP HOLDERS A CAUTION Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink If the liquid is hot it can scald you or your passenger Use only soft cups in the cup holder Hard o
28. Bluetooth audio mode is displayed on the screen The controls for the Bluetooth audio are dis played on the screen Settings gt Bluetooth o mm Yu 8 00 Settings gt connect Devic BOMM Ful 8 00 Bluetcoth Connect Bluetooth Connected Devices Bluetooth audio settings 4 Select the Audio Player key To adjust the Bluetooth audio settings follow the procedure below 1 Press the SETTING button on the control panel 2 Select the Bluetooth key 3 Select the Connected Devices key Monitor climate audio phone and voice recognition systems 4 87 Settings gt Audio Player E Yl 8 00 Settings gt Audio Player E Yl 8 00 XXXXXXXX Device Name XXXXXXXX XXXXXXXX Select Device Address XAXXXAXX Delete 5 A list of the connected Bluetooth audio 6 The Device Name and Device Address are CD CARE AND CLEANING players is displayed Select the name of the displayed on the screen Select the Select device you wish to edit key to make this device the active e Handle a CD by its edges Do not bend the Bluetooth audio player Select the Edit disc Never touch the surface of the disc key to edit the details of the player such as Device Name Select the Delete key to delete the device Always place the discs in the storage case when they are not being used To clean a disc wipe the surface from the center to the outer edge using a clean soft cloth Do
29. MP3 Sampling frequency 8 kHz 48 kHz 8 Kops 320 Kops VER 4 P sed WMA 2 WMA7 WMA8 WMAQ Rpa Sampling frequency 32 kHz 48 kHz versions 1 32 kbps 192 kbps VBR 4 AAC Sampling frequency 8 kHz 96 kHz 16 kbps 320 kbps VBR 4 ATRAC ATRAC3 ATRAC3 Plus i ID3 tag VER1 0 VER1 1 VER2 2 VER2 3 VER 2 4 MP3 only Tag information Song title and artist name WMA tag WMA only Folder levels Folder levels 8 Folders 255 including root folder Files 512 Max 255 files for one folder Text character number limitation 128 characters E EET 01 ASCII 02 ISO 8859 1 03 UNICODE UTF 16 BOM Big Endian 04 UNICODE UTF 16 Non BOM Big Endian 05 UNI Caa CODE UTF 8 06 UNICODE Non UTF 16 BOM Little Endian 07 SHIFT JIS 1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played 2 Protected WMA files DRM cannot be played Supported file systems 3 Available codes depend on what kind of media versions and information are going to be displayed 4 When VBR files are played the playback time may not be displayed correctly Monitor climate audio phone and voice recognition systems 4 47 Troubleshooting guide Symptom Cause and Countermeasure Check if the CD DVD USB device was inserted correctly Check if the CD DVD is scratched or dirty Check if there is condensation inside the player If there is wait until the condensation is gone about 1 hour
30. The indicator light on the button will come on Operate the temperature control buttons to set the desired temperature To quickly remove ice from the outside of the windows use the fan speed control dial to set the fan speed to maximum As soon as possible after the windshield is clean press the AUTO button to return to the automatic mode When the 7 front defroster button is pressed the air conditioner will automati cally be turned on at outside temperatures above 36 F 2 C The air recirculate mode automatically turns off allowing outside air to be drawn into the passenger compart ment to further improve the defogging per formance MANUAL OPERATION Fan speed control Turnthe 8 fan speed control dial to manually control the fan speed Press the AUTO button to return to automatic control of the fan speed Air recirculation Press the gt air recirculation button to recir culate interior air inside the vehicle The C amp indicator light on the button will come on The air recirculation cannot be activated when the air conditioner is in the Y front defrosting P mode or the front defrosting and foot out let mode Fresh air intake Press the amp fresh air intake button to draw outside air into the passenger compartment The indicator light on the button will come on Automatic intake air control In the AUTO mode the intake air will be con trolled automatically To manually contro
31. The power assisted steering uses a hydraulic pump driven by the engine to assist steering If the engine stops or the drive belt breaks you will still have control of the vehicle However much greater steering effort is needed especially in sharp turns and at low speeds AWARNING If the engine is not running or is turned off while driving the power assist for the steering will not work Steering will be harder to operate 5 24 Starting and driving BRAKE SYSTEM The brake system has two separate hydraulic circuits If one circuit malfunctions you will still have braking at 2 wheels BRAKE PRECAUTIONS Vacuum assisted brakes The brake booster aids braking by using engine vacuum If the engine stops you can stop the vehicle by depressing the brake pedal However greater foot pressure on the brake pedal will be required to stop the vehicle and stopping dis tance will be longer Using the brakes Avoid resting your foot on the brake pedal while driving This will overheat the brakes wear out the brake pads faster and reduce gas mileage To help reduce brake wear and to prevent the brakes from overheating reduce speed and downshift to a lower gear before going down a slope or long grade Overheated brakes may reduce braking performance and could result in loss of vehicle control AWARNING While driving on a slippery surface be careful when braking accelerating or downshifting Abrupt braking or accel e
32. The wheel nuts must be kept tight ened to specifications at all times It is recommended that wheel nuts be tightened to specification at each tire rotation interval AWARNING After rotating the tires check and adjust the tire pressure Retighten the wheel nuts when the vehicle has been driven for 600 miles 1 000 km also in cases of a flat tire etc Do not include the spare tire in the tire rotation For additional information re garding tires refer to Important Tire Safety Information US or Tire Safety Information Canada in the Warranty Infor mation Booklet 1 2 Wear indicator Location mark Tire wear and damage AWARNING Tires should be periodically in spected for wear cracking bulg ing or objects caught in the tread If excessive wear cracks bulging or deep cuts are found the tire s should be replaced The original tires have built in tread wear indicators When the wear indicators are visible the tire s should be replaced Tires degrade with age and use Have tires including the spare over 6 years old checked by a qualified technician because some tire damage may not be ob vious Replace the tires as neces sary to prevent tire failure and possible personal injury Improper service of the spare tire may result in serious personal in jury If it is necessary to repair the spare tire contact a NISSAN dealer For additional information re garding
33. Tire manufacturers apply a coating to the tires to help reduce discoloration of the rub ber If a tire dressing is applied to the tires it may react with the coating and form a compound This compound may come off the tire while driving and stain the vehicle paint If you choose to use a tire dressing take the following precautions e Use a water based tire dressing The coat ing on the tire dissolves more easily than with an oil based tire dressing 7 4 Appearance and care Apply a light coat of tire dressing to help prevent it from entering the tire tread grooves where it would be difficult to remove Wipe off excess tire dressing using a dry towel Make sure the tire dressing is com pletely removed from the tire tread grooves Allow the tire dressing to dry as recom mended by the tire dressing manufacturer CLEANING INTERIOR Occasionally remove loose dust from the interior trim plastic parts and seats using a vacuum cleaner or soft bristled brush Wipe the vinyl and leather surfaces with a clean soft cloth damp ened in mild soap solution then wipe clean with a dry soft cloth Regular care and cleaning is required in order to maintain the appearance of the leather Before using any fabric protector read the manu facturer s recommendations Some fabric pro tectors contain chemicals that may stain or bleach the seat material Use a cloth dampened only with water to clean the meter and gauge lens
34. To avoid or reduce the risk the procedures must be followed precisely A CAUTION This is used to indicate the presence of a hazard that could cause minor or moder ate personal injury or damage to your ve hicle To avoid or reduce the risk the pro cedures must be followed carefully If you see this symbol it means Do not do this or Do not let this happen lt amp If you see a symbol similar to these in an illustra tion it means the arrow points to the front of the vehicle 53 Arrows in an illustration that are similar to these indicate movement or action s t Arrows in an illustration that are similar to these call attention to an item in the illustration CALIFORNIA PROPOSITION 65 WARNING AWARNING Engine exhaust some of its constituents and certain vehicle components contain or emit chemicals known to the State of Cali fornia to cause cancer and birth defects or other reproductive harm In addition cer tain fluids contained in vehicles and cer tain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth de fects or other reproductive harm CALIFORNIA PERCHLORATE ADVISORY Some vehicle parts such as lithium batter ies may contain perchlorate material The following advisory is provided Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate BLUETOOTH
35. and other functions To start the voice recognition system push the TALK switch on the steering wheel then say a command after the tone Let s Practice Initiates a practice session that demonstrates how to improve voice recognition by the system The system will prompt you to say a phone number After you say the number the system will provide feedback to improve voice recognition When you are ready push the TALK switch Allows user to repeat the session if improvement is needed Completes practice session and returns user to the User Guide screen Using the Address Book Initiates tutorial for using the Address Book Finding a Street Address Initiates a tutorial for finding a street address Placing Calls Initiates tutorial for making a phone call by voice command operation Help on Speaking Displays useful tips of speaking for correct command recognition by the system Say commands when there are minimal background sounds Say voice commands clearly Avoid talking slow or with long pauses Say commands after the tone Voice recognition settings 2 Select Others key The available settings for the NISSAN Voice Rec 3 Select the Voice Recognition key sce os while in Standard Mode are You can confirm the page by scrolling the screen I using the NISSAN controller 1 Press the SETTING button on the control panel Allows user access to user guide settings See Displaying User Guide in this section for more information A
36. in the driver s door opening The low tire pressure warning light does not automati cally turn off when the tire pressure is ad justed After the tire is inflated to the rec ommended pressure the vehicle must be driven at speeds above 16 MPH 25 km h to activate the TPMS and turn off the low tire pressure warning light Use a tire pres sure gauge to check the tire pressure The CHECK TIRE PRESSURE warning is active as long as the low tire pressure warning light remains illuminated For additional information see Vehicle informa tion display in the Instruments and controls section and Tire Pressure Monitoring System TPMS in the Starting and driving section and in the In case of emergency section TPMS malfunction If the TPMS is not functioning properly the low tire pressure warning light will flash for approxi mately 1 minute when the ignition switch is placed in the ON position The light will remain on after the 1 minute Have the system checked by a NISSAN dealer The CHECK TIRE PRESSURE warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS mal function For additional information see Tire Pressure Monitoring System TPMS in the Starting and driving section and Tire pressure in the Main tenance and do it yourself section in this manual AWARNING Radio waves could adversely affect electrical medical equipment T
37. installed properly the seat belt is used properly and the occupant is positioned properly If the air bag status light is not illuminated reposition the occupant or child restraint in a rear seat If the passenger air bag status light will not illu minate even though you believe that the child restraint the seat belts and the occupant are properly positioned the system may be sensing an unoccupied seat in which case the air bag is OFF Your NISSAN dealer can check that the system is OFF by using a special tool However until you have confirmed with your dealer that your air bag is working properly reposition the occupant or child restraint in a rear seat The air bag system and passenger air bag status light will take a few seconds to register a change in the passenger seat status For example if a large adult who is sitting in the front passenger seat exits the vehicle the passenger air bag status light will go from OFF to ON for a few seconds and then to OFF This is normal system operation and does not indicate a malfunction If a malfunction occurs in the front passenger air bag system the supplemental air bag warning light AF located in the meter and gauges area on the driver s side of the instrument panel will blink Have the system checked by a NISSAN dealer Other supplemental front impact air bag precautions AWARNING Do not place any objects on the steering wheel pad or on the instrument panel Also do not
38. ooa 8 39 Uniform tire quality grading 9 23 Wheels andtires 8 33 Wheel tire size naoa aaa 9 8 Tire pressure Low tire pressure warning light 2 12 Tire Pressure Monitoring System TPMS 5 3 Towing Fiat TOWING 2 2 amb Oh we e A 9 22 Towing load specification 9 18 Tow truck towing aaao aa aaa 6 11 Trailer towing ws ee Bee aaae 9 15 10 6 Transceiver HomeLink Universal Transceiver 2 54 Transmission Continuously Variable Transmission CVT fluid so oee snee a aeie daaa 8 12 Driving with Continuously Variable Transmission CVT aoaaa aaa aa 5 12 Shift selector lock release nannan 5 17 Travel See registering your vehicle in another CONUN pokes net ere eae Se 9 9 Trip odomet 6 sra ewe daw abe se oes we 2 5 Trunk access through the rear seat 1 6 1 7 Trunk lid lock opener lever 3 19 TOGKNGN a eke oe hae ew a ee 2 54 Turn signal switch 04 2 34 U Uniform tire quality grading aaau 9 23 USB interface Audio file operation 4 75 4 76 Video file operation 4 78 V Vanity MITON s s a is oa E ee ee Aaa 3 26 Variable voltage control system 8 17 Vehicle dimensions and weights 9 8 Vehicle dynamic control VDC off switch 2 38 Vehicle dynamic control VDC system 5 26 Vehicle identification 0 9 9 Vehicle identification number VIN Chassis numb
39. phone and voice recognition systems 4 69 CD gt Track List XXXXXXXX mp3 XXXXXXXX mp3 Track List The tracks on the disc are displayed Select the key of a track name to begin playing that track 4 CD EJECT button Whenthe amp button is pressed with the com pact disc loaded the compact disc will be ejected When the amp button is pressed while the compact disc is being played the compact disc will eject and the system will turn off AUX auxiliary input jacks The auxiliary input jacks are located inside the center console 2 NTSC compatible devices such as video games camcorders and portable video players can be connected to the auxiliary input jacks Audio devices such as some MP3 players can also be connected to the system through the auxiliary input jacks 4 70 Monitor climate audio phone and voice recognition systems The auxiliary input jacks are color coded for iden tification purposes Red right channel audio input White left channel audio input Yellow video input Before connecting a device to the auxiliary input jacks turn off the power of the portable device With a compatible device connected to the aux iliary input jacks press the DISC AUX button repeatedly until the AUX mode appears in the display The output from the device will be played through the display when the vehicle is in the P Park position and the parking brake engaged and audio system
40. side of the storage switch 5 Pull the storage switch straight out from the fuse box 2 Maintenance and do it yourself 8 25 BATTERY REPLACEMENT A CAUTION Be careful not to allow children to swallow the battery or removed parts NISSAN INTELLIGENT KEY Replace the battery in the Intelligent Key as fol lows 1 Remove the mechanical key from the Intelli gent Key 2 Insert a small screwdriver into the slit of the corner and twist it to separate the upper part from the lower part Use a cloth to protect the casing 3 Replace the battery with a new one Recommended battery CR2032 or equiva lent Do not touch the internal circuit and elec tric terminals as doing so could cause a malfunction Hold the battery by the edges Holding the battery across the contact points will seriously deplete the storage capacity Make sure that the side faces the bot tom of the case 8 26 Maintenance and do it yourself 4 Close the lid securely as illustrated 5 Operate the buttons to check the operation See a NISSAN dealer if you need assistance for replacement FCC Notice For USA This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation Note Changes or
41. sion and returns to the call Say star for Say pound for Transfer call Use the Transfer Call com mand to transfer the call from the Bluetooth Hands Free Phone System to the cellular phone when privacy is desired The system announces Transfer call Call transferred to privacy mode The system then ends the VR session To reconnect the call from the cellular phone to the Bluetooth Hands Free System press the 4 button Mute Use the Mute command to mute your voice so the other party cannot hear it Use the mute command again to unmute your voice NOTE If a call is ended or the cellular phone network connection is lost while the Mute feature is on the Mute feature will be reset to off for the next call so the other party can hear your voice Phonebook phones without automatic phonebook download function NOTE The Transfer Entry command is not avail able when the vehicle is moving Main Menu Phonebook Transfer Entry A Delete Entry List Names Monitor climate audio phone and voice recognition systems 4 99 For phones that do not support automatic down load of the phonebook PBAP Bluetooth pro file the Phonebook command is used to manu ally add entries to the vehicle phonebook The phonebook stores up to 40 names for each phone connected to the system NOTE Each phone has
42. sixth depending on vehicle speed 5 16 Starting and driving Shift ranges up or down one by one as follows 128384868586 M6 6th Use this position for all normal forward driving at highway speeds M5 5th Use this position when driving up long slopes or for engine braking when driving down long slopes M4 4th M3 3rd and M2 2nd Use for hill climbing or engine braking on downhill grades M1 First Use this position when climbing steep hills slowly or driving slowly through deep snow sand or mud or for maximum engine braking on steep downhill grades Remember not to drive at high speeds for extended periods of time in lower than 6 range This reduces fuel economy When shifting up Move the shift lever to the up side Shifts to higher range When shifting down Move the shift lever to the down side Shifts to lower range Moving the shift lever rapidly to the same side twice will shift the ranges in succession When canceling the manual shift mode Return the shift lever to the D Drive position to return the transmission to the normal driving mode Inthe manual shift mode the transmis sion may not shift to the selected gear This helps maintain driving perfor mance and reduces the chance of ve hicle damage or loss of control Inthe manual shift mode the transmis sion may shift up automatically to a higher range than selected if the en gine speed is
43. tight This can occur even if the vehicle is parked Unbuckle the seat belt to release the child If the seat belt cannot be unbuckled or is already unbuckled release the child by cutting the seat belt with a suitable tool such as a knife or scissors to release the seat belt Front seat shown Fastening the seat belts Q Adjust the seat See Seats earlier in this section LRS2190 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage The retractor is designed to lock dur ing a sudden stop or on impact A slow pulling motion permits the seat belt to move and allows you some freedom of movement in the seat ifthe seat belt cannot be pulled from its fully retracted position firmly pull the belt and release it Then smoothly pull the belt out of the re tractor Safety Seats seat belts and supplemental restraint system 1 19 3 Position the lap belt portion low and snug on the hips as shown 4 Pull the shoulder belt portion toward the retractor to take up extra slack Be sure the shoulder belt is routed over your shoulder and across your chest The front passenger seat and the rear seating positions three point seat belts have two modes of operation Emergency Locking Retractor ELR Automatic Locking Retractor ALR The Emergency Locking Retractor ELR mode allows the seat belt to extend and retract to allo
44. ye 4 way ow wa 3 16 IntCHOrliGhts s fu 6 ee amp Gua ew oe a ee a 2 51 Interior trunk lid release 3 20 iPod Player aaau aaa wd 8 4 79 4 82 ISOFIX child restraints 1 27 J Jump Stan s cee nek ee a a A 6 8 K Keyfob battery replacement 8 26 Keyless entry With Intelligent Key system See Intelligent Key system 3 13 Keys For Intelligent Key system 3 2 L Labels Air conditioner specification label 9 11 C M V S S certification label 9 10 Emission control information label 9 10 Engine serialnumber 9 10 F M V S S certification label 0 9 10 Tire and Loading Information label 9 11 Vehicle identification number VIN plate 9 9 Warning labels for SRS 1 57 LATCH Lower Anchors and Tethers for CHildren DYSTE a e 248 ee hee eee ha ee ee 1 27 License plate Installing the license plate 9 11 Light Air bag warning light 1 57 2 14 Brake light See stop light 8 28 Bulb check instrument panel 2 10 Bulb replacement 8 28 Charge warning light 2411 Fog MICHEL SWOR oda aoe at OS ee 2 34 Headlight and turn signal switch 2 30 Headlight control switch 2 31 Headlights aao a 8 27 Interior NGI is ea a aae e aa h a E 2 51 Light PUDS 6 saa sae o ee a oa a 8 27 Low tire pressure warning light 2 12 Low windshield washer flu
45. 0 cee eee eee aes 8 2 General maintenance 00 ce eee eee eee 8 2 Explanation of general maintenance items 8 2 Maintenance precautionS 0 0c eee ees 8 5 Engine compartment check locations 8 6 Engine cooling system 020eee eee eee ee 8 8 Checking engine coolant level 005 8 9 Changing engine coolant 2 002 e0ee 8 9 ENGNG Gls 28 cdee den tice tegacatenneeaeaeses ee oee 8 10 Checking engine oil level 2 000000 8 10 Changing engine oil 2 0 cee eee eee 8 11 Changing engine oil filter 0 00 8 12 Continuously Variable Transmission CVT fluid 8 12 Power steering fluid lt us2ueeeseiegnbeecuwdaenen ve 8 13 Diane aE e E EEEE A ae Geen E A T 8 13 Blake NMG oae E E E ELE 8 14 Windshield washer fluid 022020000 8 14 Windshield washer fluid reservoir 8 14 DAC sppeagee an eeserseuetnts seeeteceetatsesetenas 8 15 Jump Stat eses tees tiene ceenteercacneceet ee 8 16 Variable voltage control system 005 8 17 DIVE Doll cn cavent concusissteetensean testes eknaes 8 17 Spak PUGS esere eniranta nET pees ee SERRE 8 18 Replacing spark plugs 0 0005 8 18 Air ClOQNelcacdancecsiseneehsduesueeeseee bea peneers 8 19 In cabin MICKONILE s 2 2 02 492 setecs tenses Steecen 8 19 Windshield wiper blades 22 22 05 8 20 Cleaning 20 edutciaddenseedishneGe
46. 1 Position the end of your hand held transmit ter 1 3 in 2 8 cm away from the HomeLink surface keeping the HomeLink indicator light in view 2 Using both hands simultaneously press and hold the desired HomeLink button and hand held transmitter button DO NOT re lease until the HomeLink indicator light flashes slowly and then rapidly When the indicator light flashes rapidly both buttons may be released The rapid flashing indi cates successful programming NOTE Some devices may require you to replace Step 2 with the cycling procedure noted in Programing HomeLink for Canadian customers and gate openers in this sec tion 3 Press and hold the HomeLink button and observe the indica tor light programmed elf the indicator light is solid continuous programming is complete and your device should acti vate when the HomeLink button is pressed and released lf the indicator light C blinks rapidly for two seconds and then turns to a solid continuous light continue with Steps 4 6 for a rolling code device A second person may make the following steps easier Use a ladder or other device Do not stand on your vehicle to perform the next steps At the receiver located on the garage door opener motor in the garage locate the learn or smart button the name and color of the button may vary by manufacturer but it is usually located near where the hanging antenna w
47. C M V S S certification label 9 10 Cold weather driving 5 28 Compact disc CD player 4 60 4 67 Console box 2 0 000 e eee eee 2 42 Continuously Variable Transmission CVT 5 12 Continuously Variable Transmission CVT fluid a so a e amp ae eo we a a a 8 12 Driving with Continuously Variable Transmission CVT aoaaa aa aaa 5 12 Transmission shift selector lock release 5 17 Control panel buttons 4 11 Brightness contrast button 4 10 4 19 Enter button 004 4 4 4 11 Without navigation system 4 4 Controls Audio controls steering wheel 4 89 Heater and air conditioner controls ie sa ce wt He ee HE Hw OH 4 30 4 34 Coolant Capacities and recommended fuel lubricants 1 ee ee 9 2 Changing engine coolant 8 9 Checking engine coolant level 8 9 Engine coolant temperature gauge 2 6 Corrosion protection 08 7 6 Cruise CODIMO s war aca 4 ey ede amp we oe week 5 19 Cup holders 228 4 lt sawn e 2 4 2 a0 2 41 2 42 Daytime running light system Canada only 2 33 10 2 Defroster switch Rear window and outside mirror defroster SWO amp Foe e ere oS ae BS es 2 Digital Versatile Disc DVD player 4 Dimensions and weights Dimmer switch for instrument panel 2 Display controls see control panel buttons 4 4 4 DOOF OCES o w 2485 5 5 eee ee
48. Connecting a device to the USB input jack AWARNING Do not connect disconnect or operate the USB device while driving Doing so can be a distraction If distracted you could lose control of your vehicle and cause an acci dent or serious injury 4 74 Monitor climate audio phone and voice recognition systems A CAUTION e Do not force the USB device into the USB port Inserting the USB device tilted or up side down into the port may damage the port Make sure that the USB device is connected correctly into the USB port Do not grab the USB port cover if so equipped when pulling the USB device out of the port This could damage the port and the cover Do not leave the USB cable in a place where it can be pulled unintentionally Pulling the cable may damage the port Refer to your device manufacturer s owner infor mation regarding the proper use and care of the device The USB input jack is located in the center con sole Insert the USB device into the jack 4 When a compatible storage device is plugged into the jack compatible audio files on the stor age device can be played through the vehicle s audio system Audio file operation AUX button Place the ignition switch in the ON or ACC position and press the AUX button to switch to the USB input mode If another audio source is playing and a USB memory device is inserted press the AUX button repeatedly until the center display changes to the USB m
49. HOOD 1 Pull the hood lock release handle located below the driver side instrument panel The hood will spring up slightly 2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood When closing the hood lower it slowly and make sure it locks into place AWARNING e Make sure the hood is completely closed and latched before driving Fail ure to do so could cause the hood to fly open and result in an accident If you see steam or smoke coming from the engine compartment to avoid injury do not open the hood TRUNK LID AWARNING e Do not drive with the trunk lid open This could allow dangerous exhaust gases to be drawn into the vehicle See Ex haust gas in the Starting and driving section of this manual Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in jured Keep the car locked with the rear seatback and trunk lid securely latched when not in use and prevent children s access to car keys Pre driving checks and adjustments 3 17 Ed cc S LPD0394 OPENER OPERATION AWARNING e Do not drive with the trunk lid open This could allow dangerous exhaust gases to be drawn into the vehicle See Ex haust gas in the Starting and driving section of this manual 3 18 Pre driving checks and adjustments Closely su
50. HomeLink does not quickly learn the hand held transmitter information replace the hand held transmitter batteries with new batteries position the hand held transmitter with its battery area facing away from the HomeLink surface press and hold both the HomeLink and hand held transmitter buttons without inter ruption position the hand held transmitter 1 3 inches 26 76 mm away from the HomeLink surface Hold the transmitter in that position for up to 15 seconds If HomeLink is not programmed within that time try holding the transmitter in another position keeping the indicator light in view at all times If you have any questions or are having difficulty programming your HomeLink buttons refer to the HomeLink web site at www homelink com or call 1 800 355 3515 CLEARING THE PROGRAMMED INFORMATION The following procedure clears the programmed information from both buttons Individual buttons cannot be cleared However individual buttons can be reprogrammed See Reprogramming a single HomeLink button in this section To clear all programming 1 Press and hold the two outer HomeLink buttons until the indicator light begins to flash in approximately 10 seconds Do not hold for longer than 20 seconds 2 Release both buttons HomeLink is now in the programming mode and can be programmed at any time beginning with Programming HomeLink Step 1 REPROGRAMMING A
51. Instruments and controls 24 Vehicle Dynamic Control VDC OFF switch P 2 37 Outside mirror controls P 3 27 Heated steering wheel switch if so equipped P 2 37 Trunk lid release switch P 3 19 Refer to the separate Navigation System Own er s Manual if so equipped See the page number indicated in paren theses for operating details Coe Se METERS AND GAUGES Tachometer Speedometer Warning indicator lights Fuel gauge Odometer twin trip odometer Trip odometer change button ae MPH WELT Ey km E z A A Z Engine coolant temperature gauge Vehicle information display Instruments and controls 2 3 Changing the display uU il iry Press the change button to change the dis v 1 play as follows S MPH Z N wW AIH y M kmh K Trip A Trip Bo Trip AL Resetting the trip odometer i A Press the change button for more than 1 sec ond to reset the currently displayed trip odometer to zero Elapsed time driving distance and average speed information is also available Refer to Control panel buttons in the Monitor climate audio phone and voice recognition systems SPEEDOMETER AND ODOMETER Odometer Twin trip odometer Se Op thie mane Speedometer The odometer twin trip odometer is displayed when the ignition switch is placed in the ON The speedometer indicates the vehicle speed position The odo
52. Shutting off your engine when safe for stops exceeding 30 60 seconds saves fuel and reduces emissions Buy an Automated Pass for Toll Roads Automated passes permit drivers to use special lanes to maintain cruising speed through the toll and avoid stopping and starting Winter Warm Up Limit idling time to minimize impact to fuel economy Vehicles typically need no more than 30 seconds of idling at start up to effec tively circulate the engine oil before driv ing Your vehicle will reach its ideal operating temperature more quickly while driving versus Idling 5 22 Starting and driving 10 Keeping your Vehicle Cool Park your vehicle in a covered parking area or in the shade whenever possible When entering a hot vehicle opening the windows will help to reduce the inside temperature faster resulting in reduced demand on your A C system INCREASING FUEL ECONOMY Keep your engine tuned up Follow the recommended scheduled main tenance Keep the tires inflated to the correct pres sure Low tire pressure increases tire wear and lowers fuel economy Keep the wheels in correct alignment Im proper alignment increases tire wear and lowers fuel economy Use the recommended viscosity engine oll See Engine oil and oil filter recommenda tions in Technical and consumer informa tion in this manual PARKING PARKING ON HILLS AWARNING e Do not stop or park the vehicle over fla
53. Vehicle Dynamic Control VDC system uses various sensors to monitor driver inputs and ve hicle motion Under certain driving conditions the VDC System helps to perform the following functions Controls brake pressure to reduce wheel slip on one slipping drive wheel so power is transferred to a non slipping drive wheel on the same axle Controls brake pressure and engine output to reduce drive wheel slip based on vehicle speed traction control function Controls brake pressure at individual wheels and engine output to help the driver maintain control of the vehicle in the following condi tions understeer vehicle tends to not follow the steered path despite increased steer ing input oversteer vehicle tends to spin due to certain road or driving conditions The VDC system can help the driver to maintain control of the vehicle but it cannot prevent loss of vehicle control in all driving situations When the VDC system operates the R indi cator in the instrument panel flashes to note the following The road may be slippery or the system may determine some action is required to help keep the vehicle on the steered path You may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood This is normal and indicates that the VDC system is working properly Adjust your speed and driving to the road conditions See Slip indicator light and Vehicle Dynamic Con
54. a compact disc is playing the compact disc will play while rewinding or fast forwarding When the button is released the compact disc will return to normal play speed TUNE FOLDER knob While playing a CD with compressed audio files turn the TUNE FOLDER knob right or left to play the next or previous folder 4 68 Monitor climate audio phone and voice recognition systems Artist XXXXAXXX Album XXXXAXXX Track XXXXXXXX Folder Track CD menu Touch the Menu key on the display while a CD or CD with compressed audio files is playing to bring up a list of options Depending on the type of CD being played the following options may be available CD gt Menu 8 00 CD gt Play Mode 8 00 CD gt Folder List 8 00 Play Mode This option allows you to alter the play pattern of the CD Touch the key of the mode you wish to apply The modes change the play pattern as follows 1 Track Repeat the current track is repeated 1 Disc Random tracks from the entire disc are played randomly 1 Folder Repeat compressed audio files CD only the current folder is repeated 1 Folder Random compressed audio files CD only tracks from the current folder are played randomly Normal Plays all tracks on the CD in sequential order until stopped Folder List The folders on the disc are displayed Select the key of a folder name to begin playing tracks from that folder Monitor climate audio
55. a language in this section Voice memory A or memory B is selected automatically If both memory locations are already in use the system will prompt you to overwrite one Follow the instructions pro vided by the system When preparation is complete and you are ready to begin press the 4 button The VA mode will be explained Follow the instructions provided by the system When training is finished the system will tell you an adequate number of phrases have been recorded 10 The system will announce that voice adap tation has been completed and the system is ready The VA mode will stop if e The 4 button is pressed for more than 5 seconds in VA mode The vehicle begins moving during VA mode The ignition switch is placed in the OFF or LOCK position Training phrases During the VA mode the system instructs the trainer to say the following phrases The system will prompt you for each phrase phonebook transfer entry dial three oh four two nine delete call back number incoming transfer entry eight pause nine three two pause seven delete all entries call seven two four zero nine phonebook delete entry next entry dial star two one seven oh yes no select missed dial eight five six nine two Bluetooth on outgoing call three one nine oh two nine seven pause pause three oh eight cancel call back number call star two zero nine five delet
56. a vehicle equipped with a continuously variable transmission an appropriate vehicle dolly MUST be placed under the towed vehicle s drive wheels Always follow the dolly manufac turer s recommendations when using their prod uct Technical and consumer information 9 23 UNIFORM TIRE QUALITY GRADING DOT Department of Transportation Quality Grades All passenger car tires must conform to federal safety requirements in addition to these grades Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width For example Treadwear 200 Traction AA Temperature A Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified gov ernment test course For example a tire graded 150 would wear one and one half 1 1 2 times as well on the government course as a tire graded 100 The relative performance of tires depends upon the actual conditions of their use however and may depart significantly from the norm due to variations in driving habits service practices and differences in road characteristics and climate Traction AA A B and C The traction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as mea sured under controlled conditions on specified government test surfaces of asphalt and con crete A tire marked C may ha
57. air condition ing system and will require the replace ment of all air conditioner system components The refrigerant HFC 134a R 134a in your NISSAN vehicle does not harm the earth s ozone layer Although this refrigerant does not affect the earth s atmosphere certain government regula tions require the recovery and recycling of any refrigerant during automotive air conditioner sys tem service A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger ant Contact a NISSAN dealer when servicing your air conditioner system SPECIFICATIONS ENGINE Model VQ35DE Type Gasoline 4 cycle DOHC Cylinder arrangement 6 cylinder V block Slanted at 60 Bore x Stroke in mm 3 760 x 3 205 95 5 x 81 4 Displacement cu in cm 213 45 8 498 Firing order 1 2 3 4 5 6 Idle speed CVT in N position Ignition timing degree B T D C at idle speed CO at idle Spark plug FXE22HR11 Spark plug gap Nominal in mm 0 043 1 1 No adjustment is necessary Camshaft operation Timing chain This spark ignition system complies with the Canadian standard ICES 002 Technical and consumer information 9 7 WHEELS AND TIRES Wheels Size Offset in mm 18 x 8 0JJ 1 97 50 19 x 8 0JJ 1 97 50 Tires P245 45VR18 P245 40VR19 245 40WR19 Spare tire T145 80D17 Speed rating 18 V 19 V 19 W 9 8 Technical and consumer information DIMENSIONS AN
58. and the contents will be played directly when the Menu Skip key is turned on Note that some discs may not be played directly even if this item is turned on Monitor climate audio phone and voice recognition systems 4 73 e CM Skip DVD VIDEO Select the CM Skip key to choose the setting time for CM backward and forward operations Use the or key to choose a setting time of 15 30 or 60 seconds e DRC DVD VIDEO DVD VR DRC Dynamic Range Compression auto matically adjusts the soundtrack volume level to maintain a more even sound to the speakers e DVD Language DVD VIDEO VIDEO CD Select the DVD Language key to open the number entry screen Input the number cor responding to the preferred language and select the OK key The DVD top menu language will be changed to the one speci fied e Display Adjust the image quality of the screen by selecting the preferred adjustment items e Audio Choose the preferred language for the au dio Subtitle DVD VIDEO DVD VR Choose the preferred language for the sub titles Display Mode DVD VIDEO VIDEO CD DVD VR Choose from the Full Wide Normal or Cinema mode Title List DVD VR Choose the preferred title from the list Play Mode Choose the preferred play mode PG PL Mode DVD VR Choose from the PG or PL mode USB INTERFACE models without Navigation System if so equipped
59. anti lock func tion is turned off The brake system then operates normally but without anti lock assistance See Brake system in the Starting and driving sec tion BRAKE or Brake warning light This light functions for both the parking brake and the foot brake systems Parking brake indicator When the ignition switch is placed in the ON position the light comes on when the parking brake is applied Low brake fluid warning light When the ignition switch is placed in the ON position the light warns of a low brake fluid level If the light comes on while the engine Is running with the parking brake not applied stop the ve hicle and perform the following 1 Check the brake fluid level Add brake fluid as necessary See Brake fluid in the Main tenance and do it yourself section of this manual 2 If the brake fluid level is correct have the warning system checked by a NISSAN dealer AWARNING Your brake system may not be working properly if the warning light is on Driv ing could be dangerous If you judge it to be safe drive carefully to the nearest service station for repairs Otherwise have your vehicle towed because driv ing it could be dangerous Pressing the brake pedal with the en gine stopped and or a low brake fluid level may increase your stopping dis tance and braking will require greater pedal effort as well as pedal travel If the brake fluid level is
60. ast played SSCS Dw Terns tothe XM band selecting the station ast played SSS oo Use Starts to play a CD Turns to the USB audio input Bluetooth Audio Turns to the Bluetooth audio system FAUX ters to the AUX input Monitor climate audio phone and voice recognition systems 4 129 Displaying user guide You can confirm how to use voice commands by accessing a simplified User Guide which con tains basic instructions and tutorials for several voice commands 1 Press the INFO button on the control panel 2 Select the Voice Recognition key 3 Select the User Guide key 4 Select an item Ret Gating Stared Lots Practice Using the Address Book Finding a Street Address Pacing Cal Help on Speaking Describes the available Voice Recognition settings See Voice Recognition Settings in this section for more information 4 130 Monitor climate audio phone and voice recognition systems USING THE SYSTEM Initialization When the ignition switch is placed in the ON position NISSAN Voice Recognition is initialized which takes a few seconds When completed the system is ready to accept voice commands If the amp switch is pressed before the initializa tion completes the display will show the mes sage System not ready or a beep sounds Before starting To get the best performance from NISSAN Voice Recognition observe the following Keep the interior of the vehicle as qu
61. be purchased A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle This manual is the same one used by the factory trained technicians working at NISSAN dealer ships Genuine NISSAN Owner s Manuals can also be purchased For USA For current pricing and availability of genuine NISSAN Service Manuals contact 1 800 450 9491 www nissan techinfo com For current pricing and availability of genuine NISSAN Owner s Manuals contact 1 800 247 5321 For Canada To purchase a copy of a genuine NISSAN Ser vice Manual or Owner s Manual for this model year and prior please contact your nearest NISSAN dealer For the phone number and loca tion of a NISSAN dealer in your area call the NISSAN Information Center at 1 800 387 0122 and a bilingual NISSAN representative will assist yOu Technical and consumer information 9 27 MEMO 9 28 Technical and consumer information 10 Index A Active Head Restraint 1 8 1 15 Air bag See supplemental restraint system bd a ae eS We Ew ae Be a 1 43 Air bag system Front See supplemental front impact air bag system 8 vawe ba as 1 50 Air bag warning light aoaaa 1 57 2 14 Air cleaner housing filter 8 19 Air conditioner Air conditioner service 4 36 Air conditioner specification label 9 11 Air conditioner system refrigerant and oilrecommendations 9 6 Heater and air c
62. button ignition switch 3 consecutive times in less than 1 5 seconds or Push and hold the push button ignition switch for more than 2 seconds NISSAN INTELLIGENT KEY BATTERY DISCHARGE If the battery of the Intelligent Key is almost dis charged the guide light A of the Intelligent Key port blinks and the indicator appears on the ve hicle information display See Vehicle informa tion display in the Instruments and controls section In this case inserting the Intelligent Key into the port B allows you to start the engine Make sure the Intelligent Key is placed in the correct direc tion The front side faces upward and the key ring side faces downward as illustrated Starting and driving 5 9 To remove the Intelligent Key from the port push the ignition switch to the LOCK position and pull the Intelligent Key out of the port NOTE The Intelligent Key port does not charge the Intelligent Key battery If you see the low battery indicator replace the battery as soon as possible See Battery replace ment in the Maintenance and do it yourself section 5 10 Starting and driving A CAUTION e Never place anything except the Intelli gent Key in the Intelligent Key port Do ing sO may cause damage to the equipment Make sure the Intelligent Key is in the correct direction when inserting it to the Intelligent Key port The engine may not start if it is in the wrong direct
63. care If accelerating or downshifting too fast the drive wheels will lose even more traction Allow more stopping distance under these conditions Braking should be started sooner than on dry pavement Allow greater following distances on slippery roads Watch for slippery spots glare ice These may appear on an otherwise clear road in shaded areas If a patch of ice is seen ahead brake before reach ing it Try not to brake while on the ice and avoid any sudden steering maneuvers Do not use the cruise control on slip pery roads Snow can trap dangerous exhaust gases under your vehicle Keep snow clear of the exhaust pipe and from around your vehicle ENGINE BLOCK HEATER if so equipped Engine block heaters are used to assist with cold temperature starting The engine block heater should be used when the outside temperature is 20 F 7 C or lower AWARNING e Do not use your engine block heater with an ungrounded electrical system or a 2 pronged adapter You can be seri ously injured by an electrical shock if you use an ungrounded connection e Disconnect and properly store the en gine block heater cord before starting the engine Damage to the cord could result in an electrical shock and can cause serious injury e Use a heavy duty 3 wire 3 pronged ex tension cord rated for at least 10 A Plug the extension cord into a Ground Fault Interrupt GFI protected grounded 110 VAC outlet Failure to u
64. checks and adjustments 3 25 oF LPD0469 Type B Without compass Type B and Type C The indicator light will illuminate when the automatic anti glare feature is operating To turn off the automatic anti glare feature press the O button for inside mirrors without compass e the button for inside mirrors with compass The indicator light will turn off 3 26 Pre driving checks and adjustments LPD0470 Type C With compass To turn on the automatic anti glare feature again press the button for inside mirrors without compass e the button for inside mirrors with compass The indicator light will turn on Some vehicles are also equipped with automatic anti glare outside mirrors For additional informa tion see Automatic anti glare outside mirrors in this section For information on HomeLink Universal Trans ceiver operation see the HomeLink Universal Transceiver in the Instruments and controls section of this manual For information on the compass display if so equipped see Compass display in the Instru ments and controls section of this manual OUTSIDE MIRRORS The outside mirror remote control will operate only when the ignition switch is in the ACC or ON position Move the small switch 1 to select the right or left mirror Adjust each mirror to the desired position using the large switch AWARNING Objects viewed in the o
65. control system and fuel consumption press the STATUS button The following information will appear when the STATUS button is pressed multiple times Audio Audio and climate control system Audio and fuel consumption Audio 4 6 Monitor climate audio phone and voice recognition systems Information 2 00 Fuel Economy Maintenance HOW TO USE THE INFO BUTTON Press the INFO button This screen sets or dis plays various information that is helpful for using the vehicle Available items include fuel economy and maintenance information Fuel Economy Displays Fuel Economy menu Distance to Empty Displays an estimation of the distance that the vehicle can be driven before refueling The DTE is constantly calculated based on the amount of fuel in the fuel tank and actual fuel consumption The display is updated every 30 seconds When the fuel level is low the DTE display will change to NOTE If the amount of fuel added while the ignition switch is OFF is small the display just before the ignition switch is turned OFF may continue to be displayed NOTE When driving uphill or rounding curves the fuel in the tank shifts which may momentarily change the display Average Fuel Economy Displays the average fuel economy since the last reset The display is updated every 30 seconds and 1 3 mi 500 m After a reset or connecting the battery cables the display might show Resetting fuel economy The average fuel econ
66. de tergent Dampen the cloth first and then wipe the screen Settings Audio Ba m fous ences 1 gt Trebe Geese t mo COS eS h Adjusi bass HOW TO SELECT MENUS ON THE SCREEN Vehicle functions are viewed on the center dis play screen in menus Whenever a menu selec tion is made or menu item is highlighted different areas on the screen provide you with important information See the following for details 1 Header Shows the path used to get to the current screen for example press the SETTING button gt Others gt then select the Audio key 4 14 Monitor climate audio phone and voice recognition systems Menu Selections Shows the options to choose within that menu screen for example Bass etc Up Down Movement Indicator Shows that the NISSAN controller may be used to move up or down on the screen and select more options Screen Count Shows the number of menu selections avail able for the current menu even if they are on multiple pages for example 1 9 Footer Information Line Provides more information if available about the menu selection currently high lighted for example Adjust bass HOW TO USE THE STATUS BUTTON The STATUS button is used to display system information Three different split screens of infor mation are available Press the STATUS button multiple times to cycle through these screens as follows Audio with Fuel Economy
67. ee oR ee Drive belt cacao dane bee eo Ae ews 8 Drive positioner Automatic 3 Driving Cold weather driving 5 Driving with Continuously Variable Transmission CVT 00 5 Precautions when starting and driving E Economy fuel a 62 a eee Wow ww 5 Emission control information label 9 Emission control system warranty 9 Engine Before starting the engine 5 Block heate 4 2 ir 4 Blo we ae ee 5 Capacities and recommended TOCIIDNCANTS a a oo eo Oe ss RE A Changing engine coolant Changing engine oil 8 Changing engine ollfilter 8 Checking engine coolant level Checking engine oillevel 8 Engine compartment check locations Engine coolant temperature gauge Engine cooling system ENJE Ols s foo ew eae ak ae 8 10 Engine oil and oil filter recommendation 9 5 Engine oil pressure warning light 2 12 Engine oil viscosity 9 6 Engine serialnumber 9 10 Engine specifications 9 7 Starting the engine 5 11 Enter button 2 244 4 eae ee ew aa 4 4 4 11 Event data recorders 9 26 Exhaust gas Carbon monoxide 5 2 Extended storage switch 8 25 Eyeglass case uaaa a 2 40 E Flashers See hazard warning flasher switch 6 2 PIATE op a ey ee eo yee A ee O 6 3 Floor mat positioning aid
68. end an action without completing it you can say Cancel or Quit at any time the system is waiting for a response The system will end the VR session Whenever the VR session is cancelled a double beep is played to indicate you have exited the system If you want to go back to the previous command you can say Go back or Correction any time the system is waiting for a response Call Main Menu Call Speak name A Phone Number Speak Digits Special Number Redial Call Back 4 98 Monitor climate audio phone and voice recognition systems Speak name If you have stored entries in the phonebook you can dial a number associated with a name See Phonebook in this section to learn how to store entries When prompted by the system say the name of the phone book entry you wish to call The system acknowledges the name If there are multiple numbers associated with the name the system asks you to choose the correct number Once you have confirmed the name and location the system begins the call Speak Digits When prompted by the system say the number you wish to call Refer to How to say numbers and Making a call by entering a phone number in this section for more details Special Number For dialing more than 10 digits or any special characters say Special Number When the system acknowledges
69. especially when small children are in the vehicle The child safety lock levers are located on the edge of the rear doors When the lever is in the unlock position the door can be opened from the outside or the inside When the lever is in the LOCK position 1 the door can be opened only from the out side NISSAN INTELLIGENT KEY AWARNING e Radio waves could adversely affect electric medical equipment Those who use a pacemaker should contact the electric medical equipment manufac turer for the possible influences before use The Intelligent Key transmits radio waves when the buttons are pressed The FAA advises the radio waves may affect aircraft navigation and communi cation systems Do not operate the In telligent Key while on an airplane Make sure the buttons are not operated unin tentionally when the unit is stored for a flight The Intelligent Key system can operate all the door locks using the remote controller function or pushing the request switch on the vehicle without taking the key out from a pocket or purse The operating environment and or conditions may af fect the Intelligent Key system operation Be sure to read the following before using the Intelligent Key system A CAUTION Be sure to carry the Intelligent Key with you when operating the vehicle Never leave the Intelligent Key in the vehicle when you leave the vehicle The Intelligent Key is always communicating wit
70. extender adds approximately 8 in 200 mm of length and may be used for either the driver or front passenger seating position See a NISSAN dealer for assistance with pur chasing an extender if an extender is required Safety Seats seat belts and supplemental restraint system 1 21 AWARNING Only NISSAN seat belt extenders made by the same company which made the Original equipment seat belts should be used with NISSAN seat belts Adults and children who can use the standard seat belt should not use an extender Such unnecessary use could result in serious personal injury in the event of an accident Never use seat belt extenders to install child restraints If the child restraint is not secured properly the child could be seriously injured in a collision or a sud den stop SEAT BELT MAINTENANCE e To clean the seat belt webbing apply a mild soap solution or any solution recom mended for cleaning upholstery or carpet Then wipe with a cloth and allow the seat belts to dry in the shade Do not allow the seat belts to retract until they are completely dry If dirt builds up in the shoulder belt guide of the seat belt anchors the seat belts may retract slowly Wipe the shoulder belt guide with a clean dry cloth Periodically check to see that the seat belt and the metal components such as buckles tongues retractors flexible wires and anchors work properly If loose parts deterioration cuts or other dam
71. federal and or local regulations and that it is properly installed AWARNING Never connect a trailer brake system di rectly to the vehicle brake system Pre towing tips Be certain your vehicle maintains a level position when a loaded and or unloaded trailer is hitched Do not drive the vehicle if it has an abnormal nose up or nose down condition check for improper tongue load overload worn suspension or other possible causes of either condition e Always secure items in the trailer to prevent load shift while driving Keep the cargo load as low as possible in the trailer to keep the trailer center of gravity low Load the trailer so approximately 60 of the trailer load is in the front half and 40 is in the back half Also make sure the load is balanced side to side Check your hitch trailer tire pressure ve hicle tire pressure trailer light operation and trailer wheel lug nuts every time you attach a trailer to the vehicle Be certain your rearview mirrors conform to all federal state or local regulations If not install any mirrors required for towing before driving the vehicle Determine the overall height of the vehicle and trailer so the required clearance is known Trailer towing tips In order to gain skill and an understanding of the vehicle s behavior you should practice turning stopping and backing up in an area which Is free from traffic Steering stability and braking perfor m
72. from the P Park position if the ignition switch is in the ON position and the brake pedal is depressed If the battery of the vehicle is discharged the push button ignition switch cannot be moved from the LOCK position Some indicators and warnings for operation are displayed on the vehicle information display See Vehicle information display in the Instruments and controls section of this manual 5 8 Starting and driving OPERATING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range When the Intelligent Key battery is almost dis charged or strong radio waves are present near the operating location the Intelligent Key sys tem s operating range becomes narrower and may not function properly If the Intelligent Key is within the operating range itis possible for anyone even someone who does not carry the Intelligent Key to turn the ignition switch to start the engine The operating range of the engine start function is inside of the vehicle 4 The luggage area is not included in the op erating range but the Intelligent Key may function lf the Intelligent Key is placed on the instru ment panel inside the glove box storage bin or door pocket the Intelligent Key may not function If the Intelligent Key is placed near the door or window outside the vehicle the Intelligent Key may function PUSH BUTTON IGNITION SWIT
73. go back to the previous com mand you can say Go back or Correc tion any time the system is waiting for a response You can cancel a command when the sys tem is waiting for a response by saying Cancel or Quit The system announces Cancel and ends the VR session You can also press and hold the button on the steering wheel for 5 seconds at any time to end the VR session Whenever the VR ses sion is cancelled a double beep is played to indicate you have exited the system Ifyou want to adjust the volume of the voice feedback press the volume control switches or on the steering wheel while being provided with feedback You can also use the radio volume control knob How to say numbers NISSAN Voice Recognition requires a certain way to speak numbers in voice commands Refer to the following rules and examples Either zero or oh can be used for 0 Example 1 800 662 6200 One eight oh oh six six two six two oh oh or One eight zero zero six six two six two oh oh Words can be used for the first 4 digits places only Example 1 800 662 6200 One eight hundred six six two six two oh oh NOT One eight hundred six six two sixty two hundred and NOT One eight oh oh six six two sixty two hundred Numbers can be spoken in small groups The system will prompt you to continue en tering digits if desired
74. half of the console box A power outlet is can be used to hang a standard size plastic A located inside the console box and there is stor grocery bag e Properly secure all cargo with ropes or age for compact discs straps to help prevent it from sliding or A CAUTION shifting In a sudden stop or collision Do not apply a total load of more than nee Cargo coue Caune peona 20 Ibs 9 kg to a single grocery hook The cargo net helps keep packages in the cargo area from moving around while the vehicle is in motion 2 42 Instruments and controls WINDOWS POWER WINDOWS AWARNING e Make sure that all passengers have their hands etc inside the vehicle while it is in motion and before closing the windows Use the window lock switch to prevent unexpected use of the power windows Do not leave children unattended inside the vehicle They could unknowingly ac tivate switches or controls and become trapped in a window Unattended chil dren could become involved in serious To install a cargo net attach the net to the retain accidents 1 Window lock button ii The power windows operate when the ignition 2 Power door lock switch To remove a cargo net detach the net from the switch is placed in the ON position or fora 3 Front passenger s side automatic win retainers period of time after the ignition switch is placed in dow switch the OFF position If the driver s or passenger s 4 Right rear passenger s side window door i
75. horn will sound once to confirm that the horn beep feature has been reactivated Deactivating the horn beep feature does not si lence the horn if the alarm is triggered WARNING SIGNALS To help prevent the vehicle from moving unex pectedly by erroneous operation of the Intelligent Key or to help prevent the vehicle from being stolen a chime or buzzer sounds from inside and outside the vehicle and a warning is displayed in the instrument panel When a chime or beep sounds or a warning is displayed be sure to check the vehicle and the Intelligent Key See the Troubleshooting guide that follows and Vehicle information display in the Instruments and controls section of this manual Pre driving checks and adjustments 3 15 TROUBLESHOOTING GUIDE Verify the location of all Intelligent Keys that are programmed for the vehicle If another Intelligent Key is in range or inside the vehicle the vehicle system may respond differently than expected ere The SHIFT P warning appears on the dis Shift the shift lever to the P Park position continuously When opening the driver s door to get out The inside warning chime sounds position position of the vehicle continuously The Intelligent Key is in the Intelligent Key port gent Key port The NO KEY warning appears on the Place the ignition switch in the OFF display the outside chime sounds 3 times f The ignition switch is placed in the ACC or position and
76. in stallation procedure steps in this section before tightening the tether strap If you have any questions when installing a top tether strap consult your NISSAN dealer for details BOOSTER SEATS Precautions on booster seats AWARNING If a booster seat and seat belt are not used properly the risk of a child being injured in a sudden stop or collision greatly increases Make sure the shoulder portion of the belt is away from the child s face and neck and the lap portion of the belt does not cross the stomach Make sure the shoulder belt is not behind the child or under the child s arm A booster seat must only be installed in a seating position that has a lap shoulder belt Safety Seats seat belts and supplemental restraint system 1 39 Booster seats of various sizes are offered by several manufacturers When selecting any booster seat keep the following points in mind Choose only a booster seat with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213 Check the booster seat in your vehicle to be sure it is compatible with the vehicle s seat and seat belt system 1 40 Make sure the child s head will be properly supported by the booster seat or vehicle seat The seatback must be at or above the center of the child s ears For example if a low back booster seat 1 is chosen the vehicle seatba
77. is a trademark owned by Bluetooth SIG Inc and licensed to Visteon and Clarion amp Bluetooth SiriusXM Satellite Radio requires subscription sold separately Not available in Alaska Hawaii or Guam For more information visit www siriusxm com Siriusxin 2013 NISSAN NORTH AMERICA INC All rights reserved No part of this Owner s Manual may be reproduced or stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Nissan North America Inc NISSAN CUSTOMER CARE PROGRAM NISSAN CARES Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns Your NISSAN dealer is always available to assist you with all your automobile sales and service needs However if there is something that your NISSAN dealer cannot assist you with or you would like to provide NISSAN directly with comments or questions please contact the NISSAN Con sumer Affairs Department using our toll free number For U S customers 1 800 NISSAN 1 1 800 647 7261 For Canadian customers 1 800 387 0122 The Consumer Affairs Department will ask for the following information Your name address and telephone number Vehicle identification number attached to the top of the instrument panel on the driver
78. its own separate phone book You cannot access Phone A s phone book if you are currently connected with Phone B Transfer Entry A Use the Transfer Entry command to store a new name in the system When prompted by the system say the name you would like to give the new entry For example say Mary If the name is too long or too short the system tells you then prompts you for a name again Also if the name sounds too much like a name already stored the system tells you then prompts you for a name again The system will ask you to transfer a phone number stored in the cellular phone s memory Enter a phone number by voice command For example say five five five one two one two See How to say numbers in this section for more information To transfer a phone number stored in the cellular phone s memory Say Transfer entry The system acknowledges the command and asks you to initiate the transfer from the phone handset The new contact phone number will be transferred from the cellular phone via the Bluetooth communication link The transfer procedure varies according to each cellular phone See the cellular phone Owner s Manual for details You can also visit www nissanusa com bluetooth for instructions on transferring phone numbers from NISSAN recommended cellular phones The system repeats the number and prompts you for the next command When you have finished entering
79. level with the dipstick It is normal to add some oil between oil maintenance intervals or during the break in period depending on the severity of operating conditions A CAUTION Oil level should be checked regularly Op erating the engine with an insufficient amount of oil can damage the engine and such damage is not covered by warranty ma TEN R LDIO641 OD a CHANGING ENGINE OIL 1 Park the vehicle on a level surface and apply Turn the engine off and wait more than 10 minutes Place a large drain pan under the drain plug A under the body Remove the oil filler cap inside the en gine compartment by turning it counter clockwise Remove the drain plug with a wrench by turning it counterclockwise and completely drain the oil If the oil filter is to be changed remove and replace it at this time See Changing engine oll filter later in this section Waste oil must be disposed of prop erly Check your local regulations AWARNING Prolonged and repeated contact with used engine oil may cause skin cancer Try to avoid direct skin contact with used oil If skin contact is made wash A CAUTION Be careful not to burn yourself The engine oil may be hot ig Clean and reinstall the drain plug and a new washer Securely tighten the drain plug with a wrench Do not use excessive force Drain plug tightening torque 22 29 ft lb 29 39 N
80. located on the steer Voice Recognition J Phone w Navigation z Practice W Information i J Audio w Help To stop prompt and say command push the TALK switch 2 A list of commands appears on the screen 3 and the system announces Please say a command After the tone sounds and the icon on the screen changes from C tB Speak a command Continue to follow the voice menu prompts and speak after the tone sounds until your desired operation is completed Monitor climate audio phone and voice recognition systems 4 121 Operating tips Say a command after the tone Voice com mands cannot be accepted when the icon iS Commands that are available are always shown on the display and spoken through voice menu prompts Commands other than those that are displayed are not accepted Please follow the prompts given by the sys tem If the command is not recognized the sys tem repeats the announcement Repeat the command in a clear voice Say Back when prompted to return to the previous screen If you want to cancel the command press and hold the amp switch The message Voice Recognition is cancelled will be dis played If you want to adjust the volume of the sys tem feedback push the volume control switch on the steering wheel or use the audio system volume knob while the system is making an announcement How to speak numbers Voice Recognition requires a ce
81. m Refill engine with recommended oil through the oil filler opening then install the oil filler cap securely See Capacities and recommended fuel lubricants in the Technical and con sumer information section of this manual for drain and refill capacity The drain and refill capacity depends on the oil temperature and drain time Use these specifications for reference only Always use the dipstick to determine when the proper amount of oil is in the engine Start the engine Check for leakage around the drain plug and oil filter Correct as re quired thoroughly with soap or hand cleaner as soon as possible 10 Turn the engine off and wait more than e Keep used engine oil out of reach of 10 minutes Check the oil level with the children dipstick Add engine oil if necessary the parking brake 2 Start the engine and let it idle until it reaches operating temperature Maintenance and do it yourself 8 11 CHANGING ENGINE OIL FILTER 1 Park the vehicle on a level surface and apply the parking brake 2 Turn the engine off 3 Place alarge drain pan under the oil filter 4 Loosen the oil filter with an oil filter wrench by turning it counterclockwise Then remove the oil filter by turning it by hand A CAUTION Be careful not to burn yourself The engine oil may be hot 8 12 Maintenance and do it yourself 5 Wipe the engine oil filter sealing surface with a clean rag A CAUTION
82. may improve clarity if reception between callers is unclear To access the volume settings press the SETTING button then select Volume and Beeps You can also adjust the volume of an incoming voice during a call by pushing the vol ume control switch on the steering wheel or by turning the volume control knob on the control panel Adjusting this setting allows ringer volume to be set at a desired level Incoming Call Adjusting this setting allows you to hear a difference in volume You can also adjust the volume of an incoming voice during a call by pushing the volume control switch on the steering wheel or by turning the volume control knob Outgoing Call Adjusting this setting allows the person you are talking with to hear a difference in volume 4 118 Monitor climate audio phone and voice recognition systems NISSAN VOICE RECOGNITION SYSTEM if so equipped NISSAN Voice Recognition allows hands free operation of the systems equipped on this ve hicle such as phone and vehicle information There are two voice recognition modes of opera tion available They are Standard Mode Alternate Command Mode In Standard Mode the factory default setting commands that are available are always shown on the display and announced by the system You can complete your desired operation by simply following the prompts given by the system Not all NISSAN Voice Recognition options are available while in Standard Mode For a
83. not to inhale it as it may cause Irritation and choking Those with a history of a breathing condition should get fresh air promptly Safety Seats seat belts and supplemental restraint system 1 55 After pretensioner activation load limiters allow the seat belt to release webbing if necessary to reduce forces against the chest The supplemental air bag warning light R is used to indicate malfunctions in the pretensioner system See SUPPLEMENTAL AIR BAG WARNING LIGHT in this section for more de tails If the operation of the supplemental air bag warning light indicates there is a malfunction have the system checked by a NISSAN dealer When selling your vehicle we request that you inform the buyer about the pretensioner system and guide the buyer to the appropriate sections in this Owner s Manual 1 SRS Air Bag Warning Labels located on the sun visors SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental front impact air bag system are placed in the vehicle as shown in the illustration 1 56 Safety Seats seat belts and supplemental restraint system LRSO100 SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light displaying AF in the instrument panel moni tors the circuits for the air bag systems preten sioners and all related wiring When the ignition switch is placed in the ON or START position the supplemental air bag warn ing light illuminates f
84. not wipe the disc using a circular motion Do not use a conventional record cleaner or alcohol intended for industrial use 4 88 Monitor climate audio phone and voice recognition systems A new disc may be rough on the inner and outer edges Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated NY LHA1144 LHA2094 Type A Type B 1 Power on and SOURCE select switch 1 Power on and SOURCE select switch 2 Tuning switch 2 Menu control switch ENTER button 3 Volume control switch 3 Volume control switch STEERING WHEEL SWITCH FOR AUDIO CONTROL The audio system can be operated using the controls on the steering wheel POWER on switch With the ignition switch in the ACC or ON posi tion push the SOURCE switch to turn the audio system on Monitor climate audio phone and voice recognition systems 4 89 SOURCE select switch Push the source select switch to change the mode in the following sequence Models without Navigation System AM FM1 FM2 XM1 XM2 XM83 satellite radio if so equipped USB iPod if so equipped CD DVD AUX AM Models with Navigation System AM FM1 FM2 XM1 XM2 XM3 satellite radio if so equipped CD DVD USB iPod Bluetooth Audio AUX AM These modes are only available when compat ible media storage Is inserted into the device Volume contro
85. numbers or transferring an entry choose Store The system confirms the name location and number Delete Entry Use the Delete Entry command to erase one entry from the phonebook After the system rec 4 100 Monitor climate audio phone and voice recognition systems ognizes the command speak the name to delete or say List Names to choose an entry List Names Use the List Names command to hear all the names in the phonebook The system recites the phonebook entries but does not include the actual phone numbers When the playback of the list is complete the system goes back to the main menu You can stop the playback of the list at any time by pressing the button on the steering wheel The system ends the VR session Phonebook phones with automatic phonebook download function NOTE The Transfer Entry command is not avail able when the vehicle is moving Main Menu Phonebook Say a Name List Names Record Name For phones that support automatic download of the phonebook PBAP Bluetooth profile the Phonebook command is used to manage en tries in the vehicle phonebook You can say the name of an entry at this menu to initiate dialing of that entry The phonebook stores up to 1000 names for each phone connected to the system When a phone is connected to the system the phonebook is automatically downloaded to the vehicle Thi
86. of the desired shift positions AWARNING Apply the parking brake if the shift lever is in any position while the engine is not running Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage P Park A CAUTION To prevent transmission damage use the P Park or R Reverse position only when the vehicle is completely stopped Use the P Park shift lever position when the vehicle is parked or when starting the engine Make sure the vehicle is completely stopped The brake pedal should be depressed to move the shift lever from N Neutral or any drive position to P Park Apply the parking brake When parking on a hill apply the parking brake first then move the shift lever into the P Park position R Reverse A CAUTION To prevent transmission damage use the P Park or R Reverse position only when the vehicle is completely stopped Use the R Reverse position to back up Make sure the vehicle is completely stopped before selecting the R Reverse position The brake pedal must be depressed to move the shift lever from P Park N Neutral or any drive position to R Reverse N Neutral Neither forward nor reverse gear is engaged The engine can be started in this position You may shift to N Neutral and restart a stalled engine while the vehicle is moving D Drive Use this position for all normal forward driving
87. op erates only when the engine is running e Do not leave children or adults who would normally require the assistance of others alone in your vehicle Pets should also not be left alone They could accidentally injure themselves or others through inadvertent operation of the vehicle Also on hot sunny days temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals e Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up Start the engine and operate the controls to activate the air conditioner Monitor climate audio phone and voice recognition systems 4 29 NOTE Odors from inside and outside the vehicle can build up in the air conditioner unit Odor can enter the passenger compartment through the vent When parking set the heater and air condi tioner controls to turn off air recirculation to allow fresh air into the passenger compart ment This should help reduce odors inside the vehicle AUTOMATIC OPERATION Cooling and or dehumidified heating AUTO This mode may be used all year round as the system automatically works to keep a constant temperature Air flow distribution and fan speed are also controlled automatically 1 Press the AUTO button on The indicator on the button will illuminate and AUTO will be displayed Operate the driver s side
88. or Snow and construction A NISSAN dealer may be able to help you with information about tire type size speed rating and availability e Replacement tires may have a lower speed rating than the factory equipped tires and may not match the potential maximum vehicle speed Never exceed the maximum speed rating of the tire For additional information regarding tires refer to Important Tire Safety In formation US or Tire Safety Informa tion Canada in the Warranty Informa tion Booklet All season tires NISSAN specifies All Season tires on some mod els to provide good performance all year includ ing snowy and icy road conditions All Season tires are identified by ALL SEASON and or M amp S on the tire sidewall Snow tires have better snow traction than All Season tires and may be more appropriate in some areas Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads Summer tire performance is substantially re duced in snow and ice Summer tires do not have the tire traction rating M amp S on the tire sidewall If you plan to operate your vehicle in snowy or icy conditions NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels Snow tires If snow tires are needed it is necessary to select tires equivalent in size and load rating to the original equipment tires If you do not it can adversely affect the safety and ha
89. or parking lights are off Instruments and controls 2 33 HORN TURN SIGNAL SWITCH Turn signal CQ Move the lever up or down to signal the turning direction When the turn is com pleted the turn signal cancels automatically 2 34 Instruments and controls FOG LIGHT SWITCH if so equipped To turn the fog lights on turn the headlight switch to the position then turn the fog light switch to the 0 position To turn the fog lights on with the headlight switch in the AUTO position the headlights must be on then turn the fog light switch to the position To turn the fog lights off turn the fog light switch to the OFF position The headlights must be on and the low beams selected for the fog lights to operate The fog lights automatically turn off when the high beam headlights are selected To sound the horn push near the horn icon on the steering wheel AWARNING Do not disassemble the horn Doing so could affect proper operation of the supplemental front air bag system Tam pering with the supplemental front air bag system may result in serious personal injury HEATED SEATS if so equipped The front seats are warmed by built in heaters The switch is located on the center console i 2 Start the engine Push the LO or HI position of the switch as desired The indicator light in the switch will illuminate The heater is controlled by a thermostat automatically turning the
90. reduce odors inside the vehicle AUTOMATIC OPERATION Cooling and or dehumidified heating AUTO This mode may be used all year round as the system automatically works to keep a constant temperature Air flow distribution and fan speed are also controlled automatically 1 Press the AUTO button on The indicator on the button will illuminate and AUTO will be displayed Turn the temperature control dial to the left or right to set the desired temperature Adjust the temperature display to about 75 F 24 C for normal operation The temperature of the passenger compart ment will be maintained automatically Air flow distribution and fan speed are also con trolled automatically A visible mist may be seen coming from the vents in hot humid conditions as the air is cooled rapidly This does not indicate a mal function You can individually set driver s and front passenger s side temperature using each temperature control dial When the DUAL button or passenger s side temperature dial is turned the DUAL indicator will come on To turn off the passenger s side temperature control press the DUAL button Heating A C OFF The air conditioner does not activate When you need to heat only use this mode 1 Press the A C button A C OFF will be displayed and A C indicator will turn off Turn the temperature control dial to set the desired temperature The temperature of the passenge
91. restraint Not all child restraints fit in all types of vehicles 7 Check to make sure that the child restraint is properly secured prior to each use If the seat belt is not locked repeat steps 1 through 6 After the child restraint is removed and the seat belt fully retracted the ALR mode child restraint mode is canceled FORWARD FACING CHILD RESTRAINT INSTALLATION USING LATCH Refer to all Warnings and Cautions in the Child safety and Child restraints sections before in stalling a child restraint Follow these steps to install a forward facing child restraint using the LATCH system 1 Position the child restraint on the seat Al ways follow the child restraint manufactur er s instructions WRS0799 Forward facing web mounted step 2 2 Secure the child restraint anchor attach ments to the LATCH lower anchors Check to make sure the LATCH attachment is prop erly attached to the lower anchors If the child restraint is equipped with a top tether strap route the top tether strap and secure the tether strap to the tether anchor point See Installing top tether strap in this section Do not install child restraints that require the use of a top tether strap in seat ing positions that do not have a top tether anchor Safety Seats seat belts and supplemental restraint system 1 33 3 WRS0800 Forward facing rigid mounted step 2 The back of the child restraint should be
92. restraint is not secure tighten the LATCH attachment as necessary or put the restraint in another seat and test it again You may need to try a different child restraint or try installing by using the vehicle seat belt if applicable Not all child restraints fit in all types of vehicles 1 30 Safety Seats seat belts and supplemental restraint system AWARNING The three point seat belt with Automatic Locking Retractor ALR must be used when installing a child restraint Failure to use the ALR mode will result in the child restraint not being properly secured The restraint could tip over or be loose and cause injury to a child in a sudden stop or collision Also it can change the operation of the front passenger air bag See Front passenger air bag and status light later in this section WRS0256 Rear facing step 1 Refer to all Warnings and Cautions in the Child safety and Child restraints sections before in stalling a child restraint Follow these steps to install a rear facing child restraint using the vehicle seat belts in the rear seats 1 Child restraints for infants must be used in the rear facing direction and therefore must not be used in the front seat Position the child restraint on the seat Always follow the restraint manufacturer s instructions WRS0761 Rear facing step 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you
93. roof rails All of the information cautions and warnings in this manual must be followed The side air bags and curtain air bags are designed to inflate in higher severity side collisions although they may inflate if the forces in another type of collision are similar to those of a higher severity impact They are designed to inflate on the side where the vehicle is impacted They may not inflate in cer tain side collisions Vehicle damage or lack of it is not always an indication of proper side air bag and curtain air bag operation When the side air bags and curtain air bags inflate a fairly loud noise may be heard followed by release of smoke This smoke is not harmful and does not indicate a fire Care should be taken not to inhale it as it may cause irritation and choking Those with a history of a breathing con dition should get fresh air promptly Side air bags along with the use of seat belts help to cushion the impact force on the chest and pelvic area of the front occupants Curtain air bags help to cushion the impact force to the head of occupants in the front and rear outboard seat ing positions They can help save lives and re duce serious injuries However an inflating side air bag and curtain air bags may cause abrasions or other injuries Side air bags and curtain air bags do not provide restraint to the lower body The seat belts should be correctly worn and the driver and passenger seated upright as
94. s side Date of purchase Current odometer reading Your NISSAN dealer s name Your comments or questions OR You can write to NISSAN with the information at For U S customers Nissan North America Inc Consumer Affairs Department P O Box 685003 Franklin TN 37068 5003 or via e mail at nnaconsumeraffairs nissan usa com For Canadian customers Nissan Canada Inc 5290 Orbitor Drive Mississauga Ontario L4W 4Z5 or via e mail at information centre nissancanada com If you prefer visit us at www nissanuSsa com for U S customers or www nissan ca for Canadian customers We appreciate your interest in NISSAN and thank you for buying a quality NISSAN vehicle Table of Contents Illustrated table of contents Safety Seats seat belts and supplemental restraint system Instruments and controls Pre driving checks and adjustments Monitor climate audio phone and voice recognition systems Starting and driving In case of emergency Appearance and care Maintenance and do it yourself Technical and consumer information _ Information Provided by et co 1 0 Illustrated table of contents Air bags seat belts and child restraints 0 2 INSUUMCMI panel ess ccerserersn ditt kinni erae 0 6 Externo MON nc eae ren ieue ween ex 0 3 Engine compartment check locations 0 8 Paco fedlanequssteramncuunstansaneneanecqustue 0 4 Warning indicator liGhtsss csc squs
95. screen 5 4 6 How to use the STATUS button 4 6 How to use the INFO button 000 4 6 How to use the SETTING button 4 8 SID OFF button 0 cece e cence eee enes 4 10 Control panel buttons color screen with Navigation System if so equipped 05 4 11 How to use the NISSAN controller 4 12 How to use the touch screen 00 cece eee 4 12 How to select menus on the screen 4 14 How to use the STATUS button 4 15 How to use the INFO button 00 4 15 How to use the SETTING button 4 17 SID OFF button 0 cece e eee ee eeeeenes 4 19 Image viewer if so equipped 0ce cece eens 4 20 Using the image viewer 2 02 005 4 20 RearView Monitor if so equipped 008 4 29 How to read the displayed lines 4 292 How to park with predicted course lines 4 23 Difference between predicted and actual GISTANCESnanac hee eet E E E E E 4 24 How to adjust the screen 0 cee eee eee 4 27 Operating HDS sere oxdatuue xeupen sanedenieanas 4 27 VS einne rinra rR unAn RE EREE abeeese aed 4 28 Heater and Air Conditioner automatic Type A 4 29 Automatic operation 00 cece eee eee 4 30 Manual operation 0 0 cece eee eee 4 31 Operating HOS ere ena esaeees serris terere n ee wea 4 31 Heater and Air Conditioner auto
96. search for and the specified file or folder will be played Display Adjust the image quality of the screen DRC DRC Dynamic Range Compression auto matically adjusts the soundtrack volume level to maintain a more even sound to the speakers Audio Choose the preferred language of the audio Subtitle Choose the preferred language of the sub titles Display Mode Choose between the Normal Wide Cinema or Full display modes Monitor climate audio phone and voice recognition systems 4 79 iIPod PLAYER OPERATION WITHOUT NAVIGATION SYSTEM if so equipped Connecting iPod AWARNING Do not connect disconnect or operate the USB device while driving Doing so can be a distraction If distracted you could lose control of your vehicle and cause an acci dent or serious injury A CAUTION e Do not force the USB device into the USB port Inserting the USB device tilted or up side down into the port may damage the port Make sure that the USB device is connected correctly into the USB port Do not grab the USB port cover if so equipped when pulling the USB device out of the port This could damage the port and the cover e Do not leave the USB cable in a place where it can be pulled unintentionally Pulling the cable may damage the port Refer to your device manufacturer s owner infor mation regarding the proper use and care of the device To connect an iPod to the vehi
97. seat belts and supplemental re straint system section of this manual and also instruct your passengers to do so Seat belts help reduce the risk of injury in collisions and rollovers In a rollover crash an unbelted or improperly belted person is significantly more likely to be injured or killed than a person properly wearing a seat belt Starting and driving 5 5 OFF ROAD RECOVERY If the right side or left side wheels unintentionally leave the road surface maintain control of the vehicle by following the procedure below Please note that this procedure is only a general guide The vehicle must be driven as appropriate based on the conditions of the vehicle road and traffic 1 Remain calm and do not overreact 2 Do not apply the brakes 3 Maintain a firm grip on the steering wheel with both hands and try to hold a straight course 4 When appropriate slowly release the accel erator pedal to gradually slow the vehicle 5 If there is nothing in the way steer the ve hicle to follow the road while vehicle speed is reduced Do not attempt to drive the ve hicle back onto the road surface until vehicle speed is reduced 6 When it is safe to do so gradually turn the steering wheel until both tires return to the road surface When all tires are on the road surface steer the vehicle to stay in the ap propriate driving lane 5 6 Starting and driving lf you decide that it is not safe to return the vehicle to
98. seat belts and supplemental restraint system 1 43 Sit upright and well back 1 44 Safety Seats seat belts and supplemental restraint system AWARNING Never let children ride unrestrained or extend their hands or face out of the window Do not attempt to hold them in your lap or arms Some examples of dangerous riding positions are shown in the illustrations AWARNING Children may be severely injured or killed when the front air bags side air bags or curtain air bags inflate if they are not properly restrained Pre teens and children should be properly re strained in the rear seat if possible Safety Seats seat belts and supplemental restraint system 1 45 Do not lean against the door A WARNING A WARNING Even with the NISSAN Advanced Air Front seat mounted side impact supple Bag System never install a rear facing mental air bags and roof mounted curtain child restraint in the front seat An in side impact supplemental air bags flating front air bag could seriously in e The si Ree pees i e side air bags and curtain air bags Mea ll toed Salih See TL A ordinarily will not inflate in the event of straints earlier in this section for details a frontal impact rear impact rollover or lower severity side collision Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents 1 46 Safety Seats seat belts and supplemental restraint system AWARN
99. set speed when going up or down steep hills If this happens drive without the cruise control To cancel the preset speed use one of the following three methods Push the CANCEL button Tap the brake pedal Push the ON OFF switch off The CRUISE indicator light in the instrument panel goes out The cruise control is automatically canceled if you depress the brake pedal while pushing the ACCEL RES or SET COAST switch The preset speed is deleted from memory the vehicle slows down more than 8 MPH 13 km h below the set speed you move the shift lever to N Neutral 5 20 Starting and driving To reset at a faster cruising speed use one of the following three methods Depress the accelerator pedal When the vehicle attains the desired speed push and release the COAST SET switch Push and hold the ACCEL RES switch When the vehicle attains the speed you de sire release the switch Push and release the ACCEL RES switch Each time you do this the set speed in creases by about 1 MPH 1 6 km h To reset at a slower cruising speed use one of the following three methods Lightly tap the brake pedal When the ve hicle attains the desired speed push the COAST SET switch and release it Push and hold the COAST SET switch Re lease the switch when the vehicle slows to the desired speed Push and release the COAST SET switch Each time you do this the set speed de creases by about
100. such as when per forming periodic maintenance cleaning the ve hicle etc Additional information on the following items with an is found later in this sec tion Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not bind or require uneven effort Keep the floor mat away from the pedal Brake pedal Check the pedal for smooth opera tion If the brake pedal suddenly goes down fur ther than normal the pedal feels spongy or the vehicle seems to take longer to stop see a NISSAN dealer immediately Keep the floor mat away from the pedal Brakes Check that the brakes do not pull the vehicle to one side when applied Continuously Variable Transmission CVT P Park position mechanism On a fairly steep hill check that the vehicle is held securely with the shift lever in the P Park position without applying any brakes Parking brake Check the parking brake opera tion regularly The vehicle should be securely held on a fairly steep hill with only the parking brake applied If the parking brake needs adjustment see a NISSAN dealer Seats Check seat position controls such as seat adjusters seatback recliner etc to ensure they operate smoothly and all latches lock securely in every position Check that the head restraints move up and down smoothly and the lock knobs if so equipped hold securely in all adjustable positions Maintenance and do it yourself 8 3 Seat belts Check tha
101. tem refer to the Navigation System Owner s Manual of your vehicle For vehicles in the U S the factory default setting is the Standard Mode See NISSAN Voice Rec ognition Standard Mode in this section For ve hicles in Canada the factory default setting is the Alternate Command Mode See NISSAN Voice Recognition Alternate Command Mode in this section NISSAN VOICE RECOGNITION STANDARD MODE The Standard Mode enables control of naviga tion phone and vehicle information With this setting active commands that are available are always shown on the display and announced by the system Displaying user guide If you use the NISSAN Voice Recognition system for the first time or you do not know how to operate it you can display the User Guide for confirmation You can confirm how to use voice commands by accessing a simplified User Guide which con tains basic instructions and tutorials for several voice commands 1 Press the INFO button on the control panel Press the Others key Select the Voice Recognition key Select the User Guide key a FPF ON Select an item NOTE You can skip steps 1 to 3 by pressing the button and saying Help fol lowed by User Guide Monitor climate audio phone and voice recognition systems 4 119 Getting Started The following message will appear With voice recognition you can use voice commands to control navigation audio phone
102. the vehicle The Si light should turn off after a few driving trips If the ENGINE light does not turn off after a few driving trips have the vehicle inspected by a NISSAN dealer You do not need to have your vehicle towed to the dealer Instruments and controls 2 15 Malfunction indicator light blinking An en gine misfire has been detected which may damage the emission control system To re duce or avoid emission control system dam age do not drive at speeds above 45 MPH 72 km h avoid hard acceleration or deceleration avoid steep uphill grades if possible reduce the amount of cargo being hauled or towed The malfunction indicator light may stop blinking and come on steady Have the vehicle inspected by a NISSAN dealer You do not need to have your vehicle towed to the dealer A CAUTION Continued vehicle operation without hav ing the emission control system checked and repaired as necessary could lead to poor driveability reduced fuel economy and possible damage to the emission con trol system 2 16 Instruments and controls Security indicator light This light blinks when the ignition switch is placed in the OFF LOCK or ACC position The blinking security indicator light indicates that the security systems equipped on the vehicle are operational For additional information see Security sys tems later in this section Side light and headlight indicator light g
103. the device can be connected to the vehicle s audio system so that the audio files on the device play through the vehicle s speakers Monitor climate audio phone and voice recognition systems 4 85 Settings gt Bluetooth o MDYa 8 00 Bluetooth LHA1316 Connecting Bluetooth audio To connect your Bluetooth audio device to the vehicle follow the procedure below 1 Press the SETTING button on the control panel 2 Select the Bluetooth key 3 Select the Connect Bluetooth key Settings gt Bluetooth o MYu 8 00 Are you connecting a Bluetooth device to use with the handsfree phone system For audio devices please select No Yes LHA1317 4 A screen will appear asking if you are con necting the device to use with the hands free phone system Select the No key 4 86 Monitor climate audio phone and voice recognition systems Settings gt Connect Bluetooth 8 00 Start connecting your Bluetooth Audio device The PIN is 0000 Please input passkey LHA1351 5 Enter a PIN of your choice It will be needed by your Bluetooth audio device to com plete the connection process See the Bluetooth audio device s owner s manual for more information Bluetooth Audio Artist XXXXXAXKXAXXX Album XXXXXAXAKXAXXX Track MKXKAXKXXK Shuffle OFF Repeat OFF 0 11 Audio main operation To switch to the Bluetooth audio mode press the DISC AUX button repeatedly until the
104. the extension sun visor in or out as needed A CAUTION e Do not store the sun visor before return ing the extension to its original position Do not pull the extension sun visor forcedly downward VANITY MIRRORS To access the vanity mirror pull the sun visor down and flip open the mirror cover The vanity mirror will illuminate when the mirror cover is open MIRRORS AUTOMATIC ANTI GLARE REARVIEW MIRROR The inside mirror is designed so that it automati cally dims during night time conditions and ac cording to the intensity of the headlights of the vehicle following you The automatic anti glare feature is activated when the ignition switch is placed in the ON position NOTE Do not hang any objects over the sensors or apply glass cleaner to the sensors Doing so will reduce the sensitivity of the sensors resulting in improper operation WPD0446 Type A Type A The indicator light will illuminate when the automatic anti glare feature is operating With the ignition switch placed in the ON posi tion press the button as described To turn off the anti glare feature press the button The indicator light will turn off To turn on the anti glare feature press the button again The indicator light will turn on For information on the compass display if so equipped see Compass display in the Instru ments and controls section of this manual Pre driving
105. the inside warning chime sounds for ON position approximately 3 seconds When closing the door after getting out of The NO KEY warning appears on the dis The ignition switch is placed in the ACC Move the shift lever to the P Park position the vehicle play and the outside chime sounds position and the shift lever is not in the P and place the ignition switch in the OFF continuously Park position position The shift P warning light appears on the The ignition switch is placed in the OFF Move the shift lever to the P Park position display and the outside chime sounds position and the shift lever is not in the P continuously Park position When closing the door with the inside lock The outside chime sounds for approximately The Intelligent Key is inside the vehicle or Carry the Intelligent Key with you knob placed in the LOCK position 3 seconds and all the doors unlock trunk The Intelligent Key is inside the vehicle or Carry the Intelligent Key with you trunk cnet ew te nenielereaueet aa CAME SUNAS TON APPTOXIMAIE Y A door is not closed securely Close the door securely The door handle request switch is pushed Push the door handle request switch after before the door is closed the door is closed When closing the trunk lid The outside chime sounds for approximately The Intelligent Key is inside the trunk Carry the Intelligent Key with you 10 seconds and the trunk lid opens 3 16 Pre driving checks and adjustments
106. the port and any door open all doors will lock and unlock automatically With the Intelligent Key left in the vehicle not in the Intelligent Key port and any door open all doors will unlock automatically and a chime will sound after the door is closed AUTOMATIC DOOR LOCKS All doors lock automatically when the vehicle speed reaches 15 MPH 24 km h e All doors unlock automatically when the ig nition is placed in the OFF position The automatic unlock function can be de activated or activated To deactivate or acti vate the automatic door unlock system perform the following procedure 1 Close all doors 2 Place the ignition switch in the ON position 3 Within 20 seconds of performing Step 2 push and hold the power door lock switch to the amp position UNLOCK for more than 5 seconds 3 6 Pre driving checks and adjustments 4 When activated the hazard indicator will flash twice When deactivated the hazard indicator will flash once 5 The ignition switch must be placed in the OFF and ON position again between each setting change When the automatic door unlock system is deac tivated the doors do not unlock when the ignition switch is placed in the OFF position To unlock the door manually use the inside lock knob or the power door lock switch driver s or front passen ger s side CHILD SAFETY REAR DOOR LOCK Child safety locks help prevent the rear doors from being opened accidentally
107. the ve hicle may be moved to the desired location If the shift lever cannot be moved out of P Park have a NISSAN dealer check the transmission as soon as possible AWARNING If the shift lever cannot be moved from the P Park position while the engine is run ning and the brake pedal is depressed the stop lights may not work Malfunctioning stop lights could cause an accident injur ing yourself and others Starting and driving 5 17 Accelerator downshift in D Drive position and manual shift mode For passing or hill climbing depress the accel erator pedal to the floor This shifts the transmis sion down into lower range depending on the vehicle speed High fluid temperature protection mode This transmission has a high fluid temperature protection mode If the fluid temperature be comes too high for example when climbing steep grades in high temperatures with heavy loads such as when towing a trailer engine power and under some conditions vehicle speed will be decreased automatically to reduce the chance of transmission damage Vehicle speed can be controlled with the accelerator pedal but the engine and vehicle speed may be limited Fail safe If the vehicle is driven under extreme con ditions such as excessive wheel spinning and subsequent hard braking the fail safe system may be activated The MIL may come on to indicate the fail safe mode is activated see Malfunction Indicator Light
108. the vehicle s suspension If suspension parts such as shock ab sorbers struts springs stabilizer bars bushings and wheels are not NISSAN recommended for your vehicle or are extremely deteriorated the VDC system may not operate properly This could adversely affect vehicle handling per formance and the indicator may flash or the ft indicator light may illuminate If brake related parts such as brake pads rotors and calipers are not NISSAN recommended or are extremely deteriorated the VDC system may not operate properly and the ft indica tor light may illuminate If engine control related parts are not NISSAN recommended or are extremely deteriorated the ft indicator light may illuminate When driving on extremely inclined sur faces such as higher banked corners the VDC system may not operate prop erly and the R indicator may flash or the indicator light may illuminate Do not drive on these types of roads When driving on an unstable surface such as a turntable ferry elevator or ramp the indicator may flash or the indicator light may illuminate This is not a malfunction Restart the engine after driving onto a stable surface If wheels or tires other than the NISSAN recommended ones are used the VDC system may not operate properly and the ft indicator may flash or the indicator light may illuminate The VDC system is not a substitute for winter tires or tire chains on a snow covered ro
109. the window will be immediately low ered If the windows do not close automatically If the power window automatic function closing only does not operate properly perform the fol lowing procedure to initialize the power window system 1 Place the ignition switch in the ON position 2 Close the door 3 Open the window more than halfway by operating the power window switch 4 Pull the power window switch and hold it to close the window and then hold the switch for more than 3 seconds after the window Is closed completely 5 Release the power window switch Operate the window by automatic function to confirm the initialization is complete 6 Perform steps 2 through 5 above for other windows If the power window automatic function does not operate properly after performing the above pro cedure have your vehicle checked by a NISSAN dealer Instruments and controls 2 45 MOONROOF if so equipped O e lt LIC1408 POWER MOONROOF The moonroof will only operate when the ignition switch is placed in the ON position The power moonroof is operational for a period of time even if the ignition switch is placed in the ACC or OFF position If the driver s door or the front passen ger s door is opened during this period of time the power to the moonroof is canceled Sliding the moonroof To fully open the moonroof push the switch toward gt A To fully close the moonroof push the switch
110. time Delete Phone Use the Delete Phone command to delete a phone that is connected to the vehicle The sys tem will list the names assigned to each phone and then prompt you for the phone you wish to delete Deleting a phone from the vehicle will also delete that phonebook for that phone Turn Bluetooth OFF Use the Turn Bluetooth OFF command to prevent a wireless connection to your phone VOICE ADAPTATION VA MODE Voice Adaptation allows up to two out of dialect users to train the system to improve recognition accuracy By repeating a number of commands the users can create a voice model of their own voice that is stored in the system The system is capable of storing a different voice adaptation model for each connected phone Training procedure The procedure for training a voice is as follows 1 Position the vehicle in a reasonably quiet outdoor location 2 Sit in the driver s seat with the engine run ning the parking brake on and the transmis sion in P Park 4 102 Monitor climate audio phone and voice recognition systems Press and hold the C6 button for more than 5 seconds The system announces Press the PHONE SEND 4 button for the hands free phone system to enter the voice adaptation mode or press the PHONE END button to select a different lan guage _ Press the button For information on selecting a different lan guage see Choosing
111. tires refer to Important Tire Safety Information US or Tire Safety Information Canada in the Warranty Infor mation Booklet Maintenance and do it yourself 8 41 Replacing wheels and tires When replacing a tire use the same size tread design speed rating and load carrying capacity as originally equipped Recommended types and sizes are shown in Wheels and tires in the Technical and consumer information section of this manual AWARNING The use of tires other than those recom mended or the mixed use of tires of different brands construction bias bias belted or radial or tread patterns can adversely affect the ride braking handling VDC system ground clear ance body to tire clearance tire chain clearance speedometer calibration headlight aim and bumper height Some of these effects may lead to acci dents and could result in serious per sonal injury If your vehicle was originally equipped with 4 tires that were the same size and you are only replacing 2 of the 4 tires install the new tires on the rear axle Placing new tires on the front axle may cause loss of vehicle control in some driving conditions and cause an acci dent and personal injury 8 42 Maintenance and do it yourself If the wheels are changed for any rea son always replace with wheels which have the same off set dimension Wheels of a different off set could cause premature tire wear degrade ve hic
112. tires or wheels on the vehicle that prevent the TPMS from functioning properly Always check the TPMS malfunction telltale after replac ing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly Starting and driving 5 3 Additional information The TPMS does not monitor the tire pressure of the spare tire The TPMS will activate only when the vehicle is driven at speeds above 16 MPH 25 km h Also this system may not detect a sudden drop in tire pressure for example a flat tire while driving The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted After all 4 tires are inflated to the recommended pressure the vehicle must be driven at speeds above 16 MPH 25 km h to activate the TPMS and turn off the low tire pressure warning light Use a tire pressure gauge to check the tire pressure The CHECK TIRE PRESSURE warning ap pears in the vehicle information display when the low tire pressure warning light is illumi nated and low tire pressure is detected The CHECK TIRE PRESSURE warning turns off when the low tire pressure warning light turns off The CHECK TIRE PRESSURE warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS malfunction 5 4 Starting and driving Tire pressure rises and falls depending on the heat caused by the veh
113. to access out going incoming missed calls and to call back the last incoming call or to redial the last outgoing call Outgoing Use the Outgoing command to list the outgoing calls made from the vehicle Incoming Use the Incoming command to list the incoming calls made to the vehicle Missed Use the Missed command to list the calls made to the vehicle that were not answered Call Back Use the Call Back command to dial the number of the last incoming call to the vehicle Redial Use the Redial command to dial the number of the last outgoing call from the vehicle Monitor climate audio phone and voice recognition systems 4 101 Connect Phone NOTE The Add Phone command is not available when the vehicle is moving Main Menu Connect Phone Add Phone A Select Phone Delete Phone Turn Bluetooth OFF Use the Connect Phone commands to manage the phones connecting to the vehicle or to enable the Bluetooth function on the vehicle Add Phone A Use the Add Phone command to add a phone to the vehicle See Connecting procedure in this section for more information Select Phone Use the Select Phone command to select from a list of phones connected to the vehicle The sys tem will list the names assigned to each phone and then prompt you for the phone you wish to select Only one phone can be active at a
114. vehicle information display The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position If the vehicle has been off for awhile the pres sures will not be displayed immediately When the vehicle is driven the pressures will automati cally be displayed Instruments and controls 2 19 In case of a low tire pressure a warning message will also appear in the vehicle information display See Check tire pressure warning later in this section 2 20 Instruments and controls OUTSIDE TEMP 71 F Exterior temperature mode The exterior temperature mode can be selected to provide you with the temperature outside of your vehicle SETTING iid gt MAINTENANCE gt ALERT gt OPTIONS GENTER NEXT Setting mode The setting mode allows you to set reminders or preferences for alerts maintenance intervals or language displays In the setting mode screen press to move to Alert Maintenance Options and press to select the menu ALERT SBACK qe TO REST gt ICY LAENTER NEXT Alert mode The alert mode allows you to set alerts notifying you of time to rest or icy conditions The time to rest alert lets you know when you have been traveling for a long time and may need a break The icy alert notifies you that icy driving condi tions may exist TIMER SBACK gt SETTING GEENTER NEXT Reset mode The reset mode
115. wear eye protection whenever you work on your vehicle Your vehicle is equipped with an auto matic engine cooling fan It may come on at any time without warning even if the ignition switch is in the OFF posi tion and the engine is not running To avoid injury always disconnect the negative battery cable before working near the fan If you must run the engine in an en closed space such as a garage be sure there is proper ventilation for exhaust gases to escape Never get under the vehicle while it is supported only by a jack If it is neces sary to work under the vehicle support it with safety stands Keep smoking materials flame and sparks away from the fuel tank and battery On gasoline engine models the fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off Maintenance and do it yourself 8 5 ENGINE COMPARTMENT CHECK LOCATIONS A CAUTION e Do not work under the hood while the engine is hot Turn the engine off and wait until it cools down Avoid contact with used engine oil and coolant Improperly disposed engine oil engine coolant and or other vehicle fluids can damage the environment Al ways conform to local regulations for TATA TAT gt disposal of vehicle fluid Ao Never leave the engine or automatic transmission related component har nesses disconnected while the ignition switch is in the ON pos
116. when you try to call 800 662 6200 say eight zero zero first and the system will then ask you for the next three digits Then say six six two After recognition the system will then ask for the last four digits Say six two zero zero Using this method of phone digit entry can improve recognition perfor mance NOTE When speaking a house number speak the number 0 as zero or oh If the letter O is included in the house number it will not be recognized as 0 even if you speak oh instead of zero Voice recognition settings The available settings for the NISSAN Voice Rec ognition system while in Alternate Command Mode are described 1 Press the SETTING button on the control panel 2 Select Others key 3 Select the Voice Recognition key You can confirm the page by scrolling the screen using the NISSAN controller Command List When Alternate Command Mode is activated this key will allow user to access the list of Phone Navigation Information Audio and Help com mands Allows user access to user guide settings See Displaying User Guide in this section for more information Speaker Adaptation When Alternate Command Mode is activated this key will allow user to initiate a system function for better voice recognition performance See Speaker Adaptation Function in this section for more information Alternate Command Mode Allows user to
117. while the iPod was playing pressing the VOL ON OFF control knob will start the iPod DISC AUX button When the DISC AUX button is pressed with the system off and the iPod connected the system will turn on If another audio source is playing and the iPod is connected press the DISC AUX button repeatedly until the center display changes to the iPod mode Monitor climate audio phone and voice recognition systems 4 83 iPod gt Music 8 00 Playlists Artists Interface The interface for iPod operation shown on the vehicle center display is similar to the iPod interface Use the NISSAN controller and the BACK button to play the iPod with your favorite settings The touchscreen can also be used to control your favorite settings The following items can be chosen from the menu list screen For further information about each item see the iPod Owner s Manual Now Playing Playlists e Artists Albums Songs Podcasts Genres Composers Audiobooks Shuffle Songs e Play Mode The following keys shown on the screen are also available MENU returns to the previous screen e Pll plays pauses the music selected 4 84 Monitor climate audio phone and voice recognition systems iPod gt Play Mode Play mode While the iPod is playing touch the Menu key to display the iPod menu Touch the Play Mode key to display the Play Mode screen and adjust the settings for Shuffl
118. window defroster switch P 2 29 Interior trunk lid release P 3 19 Trunk lid P 3 17 Vehicle loading P 9 12 Exterior trunk lid release request button P 3 12 Replacing bulbs P 8 30 Fuel filler cap fuel recommendation P 3 20 P 9 28 Fuel filler door P 3 20 Child safety rear door locks P 3 6 See the page number indicated in paren theses for operating details PASSENGER COMPARTMENT 1 Interior trunk access P 1 5 2 Moonroof if so equipped P 2 46 3 Sun visors P 3 24 4 Interior lights illuminated entry P 2 50 5 HomeLink universal transceiver if so equipped P 2 53 ra Efel 6 Interior mirrors P 3 25 Yi F T T 7 Glove box P 2 41 VA O NASR 8 Cup holders P 2 40 JAANE i STA 9 Console box P 2 41 KA TANS y ie 10 Front seat P 1 2 aX y Ja LR SAS 11 Rear seat P 1 5 See the page number indicated in paren theses for operating details PIT WIN illustrated table of contents 0 5 INSTRUMENT PANEL 8 Shift paddles if so equipped P 5 15 9 Windshield wiper washer switch P 2 28 a 10 Display screen Navigation system a if so equipped P 4 11 11 Display screen Navigation system controls if so equipped P 4 11 12 Front passenger supplemental air bag P 1 56 ee 13 Glove box P 2 41 14 Display screen models without Navi gation system P 4 4 15 Climate controls models with
119. windshield is not clear after using the windshield washer or if a wiper blade chatters when running wax or other material may be on the blade or windshield Clean the outside of the windshield with a washer solution or a mild detergent Your windshield is clean if beads do not form when rinsing with clear water Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent Then rinse the blades with clear water If your wind shield is still not clear after cleaning the blades and using the wiper replace the blades 8 20 Maintenance and do it yourself A CAUTION Worn windshield wiper blades can dam age the windshield and impair driver vision REPLACING Replace the wiper blades if they are worn C Lift the wiper arm away from the windshield 2 Push the release tab then move the wiper blade down the wiper arm to remove 3 Remove the wiper blade 4 Insert the new wiper blade onto the wiper arm until it clicks into place A CAUTION e After wiper blade replacement return the wiper arm to its original position otherwise it may be damaged when the hood is opened Make sure the wiper blades contact the glass otherwise the arms may be dam aged from wind pressure Be careful not to let anything get into the washer nozzle A This may cause clogging or improper windshield washer operation If something gets into the nozzle remove it with a needle or small pin
120. with many tall buildings It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist Static Caused by thunderstorms electrical power lines electric signs and even traffic lights SATELLITE RADIO RECEPTION if so equipped When the satellite radio is used for the first time or the battery has been replaced the satellite radio may not work properly This is not a mal function Wait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data The satellite radio mode will be skipped unless an optional satellite receiver and antenna are in stalled and a SiriusXM Satellite Radio service subscription is active Satellite radio is not avail able in Alaska Hawaii and Guam Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal If possible do not put cargo over the satellite antenna A build up of ice on the satellite radio antenna can affect satellite radio performance Remove the ice to restore satellite radio reception XM is a registered trademark of SiriusXM Sat ellite Radio Inc 4 36 Monitor climate audio phone and voice recognition systems COMPACT AUDIO OPERATION PRECAUTIONS Compact disc CD player models without Navigation System A CAUTION e Do not force a compact disc into the CD insert slot T
121. with large quantities of data such as for high bit rate data files Moves immediately to the If an unsupported compressed audio file has been given a supported extension like MP3 or when play is prohibited by copyright protection the next song when playing player will skip to the next song Songs do not play back in The playback order is the order in which the files were written by the writing software Therefore the files might not play in the desired order the desired order Random Shuffle may be active on the audio system or on the USB device 4 48 Monitor climate audio phone and voice recognition systems Compressed Video Files models with Navigation System Explanation of terms e DivX DivX refers to the DivX codec owned by Div Inc used for a lossy compres sion of video based on MPEG 4 e AVI AVI stands for Audio Video Interleave It is standard file format originated by Micro soft Corporation A divx encoded file can be saved into the avi file format for playback on this system if it meets the requirements stated in the table in this section However all avi files are not playable on this system since different encodings can be used other than the DivX codec e ASF ASF stands for Advanced Systems Format It is a file format owned by Microsoft Corporation Note Only asf files that meet the requirements stated in the table in this section can be played Bit rate Bit rate denotes th
122. 1 MPH 1 6 km h To resume the preset speed push and re lease the ACCEL RES switch The vehicle re turns to the last set cruising speed when the vehicle speed is over 25 MPH 40 km h To turn off the cruise control use one of the following three methods Push the CANCEL button Tap the brake pedal Push the ON OFF switch off The CRUISE indicator light in the instrument panel goes out BREAK IN SCHEDULE A CAUTION During the first 1 200 miles 2 000 km follow these recommendations to obtain maximum engine performance and ensure the future reliability and economy of your new vehicle Failure to follow these rec ommendations may result in shortened engine life and reduced engine performance Avoid driving for long periods at constant speed either fast or slow and do not run the engine over 4 000 RPM Do not accelerate at full throttle in any gear Avoid quick starts Avoid hard braking as much as possible Do not tow a trailer for the first 500 mi 800 km Your engine axle or other parts could be damaged FUEL EFFICIENT DRIVING TIPS Follow these easy to use Fuel Efficient Driving Tips to help you achieve the most fuel economy from your vehicle 1 Use Smooth Accelerator and Brake Pedal Application Avoid rapid starts and stops Use smooth gentle accelerator and brake application whenever possible Maintain constant speed while commut ing and coast whenever possible 2 Maintai
123. 2 10 Instruments and controls e rs Supplemental air bag warning light Continuously Variable Transmission CVT indicator light Continuously Variable Transmission CVT position indicator light CRUISE Cruise main switch indicator light Front fog light indicator light if so equipped Front passenger air bag status light High beam indicator light blue If equipped the following lights come on briefly and then go off ABS o amp A 2 ov W If any light fails to come on it may indicate a burned out bulb or an open circuit in the electrical system Have the system repaired promptly ENGINE Malfunction Indicator Light MIL SOON Security indicator light Side light and headlight indicator light green Slip indicator light Turn signal hazard indicator lights Vehicle Dynamic Control OFF indicator light WARNING LIGHTS For additional information on warnings and indi cators see Vehicle information display later in this section ABS Anti lock Braking System ABS warning light When the ignition switch is placed in the ON position the Anti lock Braking System ABS warning light illuminates and then turns off This indicates the ABS is operational If the ABS warning light illuminates while the engine is running or while driving it may indicate the ABS is not functioning properly Have the system checked by a NISSAN dealer If an ABS malfunction occurs the
124. 20590 You can also obtain other information about motor vehicle safety from http www safercar gov You may notify NISSAN by contacting our Consumer Affairs Department toll free at 1 800 NISSAN 1 For Canada If you believe that your vehicle has a de fect which could cause a crash or could Cause injury or death you should immedi ately inform Transport Canada in addition to notifying NISSAN If Transport Canada receives complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may request that NISSAN con duct a recall campaign However Trans port Canada cannot become involved in individual problems between you your dealer or NISSAN You may contact Transport Canada s De fect Investigations and Recalls Division toll free at 1 800 333 0510 You may also report safety defects online at https wwwapps tc gc ca Saf Sec Sur 7 PCDB BDPP Index aspx Additional information concerning motor vehicle safety may be obtained from Trans port Canada s Road Safety Information Centre at 1 800 333 0371 or online at www tc gc ca roadsafety English speak ers or www tc gc ca securiteroutiere French speakers To notify NISSAN of any safety concerns please contact our Consumer Information Centre toll free at 1 800 387 0122 Technical and consumer information 9 25 READINESS FOR INSPECTION MAINTENANCE I M TEST Due to legal requirements in some states and Canadi
125. 23 Seatbelts o oaa a aa 1 16 Shoulder belt height adjustment 1 22 Three point type with retractor 1 19 Seat belt warning light a aoaaa aaa aa 2 14 Seats Adjustment 66 6 24240468084 1 2 Automatic drive positioner s a 3 30 Front seats oaoa aaa es 1 2 Heated seats 004 2 35 2 37 Rear seat l ou aa a a 1 6 Security indicator light 2 16 Security system NISSAN vehicle immobilizer system engine start 2 27 3 3 5 10 Self adjusting brakes 04 8 21 Service manual order form 9 26 Servicing air conditioner 4 36 Shifting Continuously Variable Transmission C50 ee ee er ee ee 5 14 Shift lock release 0 0008 5 17 Shoulder belt height adjustment 1 22 Spark plug replacement aooaa aaa 8 18 Speedometer oaoa a 2 5 Spotlights See map light 2 53 SRS warning label 1 57 Starting Before starting the engine naaa 5 11 Jump starting lt se s aoe ose he e e a 6 8 Precautions when starting and driving 5 2 Push starting oaa aaa 6 10 Starting the engine 5 11 Steering Heated steering wheel 2 37 Power steering fluid 8 13 Power steering system 5 24 Steering wheel audio control switch 4 89 SOPORE a coe Gate a Se ee ee ee 8 28 S Orage i o a ee oraw ae a ae 2 39 Sunglasses case o oo 2 40 Sunglasses holder aoaaa aa
126. 4 Front passenger position The booster seat should be positioned on the vehicle seat so that it is stable If necessary adjust or remove the head restraint headrest to obtain the correct booster seat fit If the head restraint headrest is removed store it in a secure place Be sure to reinstall the head _ restraint headrest when the booster seat is removed See Head restraints headrests in this section for head restraint headrest adjustment removal and installation information If the seating position does not have an adjustable head restraint headrest and it is interfering with the proper booster seat fit try another seating position or a different booster seat Position the lap portion of the seat belt low and snug on the child s hips Be sure to follow the booster seat manufacturer s in structions for adjusting the seat belt routing Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack Be sure the shoulder belt is positioned across the top middle portion of the child s shoulder Be sure to follow the booster seat manufacturer s instructions for adjusting the seat belt routing Follow the warnings cautions and instruc tions for properly fastening a seat belt shown in Three point type seat belt with retractor earlier in this section Safety Seats seat belts and supplemental restraint system 1 41 7 lf the booster seat is installed i
127. A CALL When you hear a phone ring the display will change to phone mode To receive a call follow one of the procedures listed below Press the button on the steering wheel Accept an incoming call to talk Answer key on the display Accept an incoming call to talk Hold Call key on the display Put an incoming call on hold Reject Call key on the display Reject an incoming call 4 114 Monitor climate audio phone and voice recognition systems DURING A CALL There are some options available during a call Select one of the following displayed on the screen if necessary Hang Up Finish the call If pressed while another caller is on hold current call will be ended and user will be able to speak to the caller that was previously on hold Use Handset Transfer the call to the cellular phone Mute Mute your voice to the person e This will appear after the Mute key is selected Mute will be cancelled Mute Keypad Brings up a keypad Enter digits when needed For example entering your PIN number for voicemail Note O Press the button during a call to send numbers and digits using Voice Recognition Switch Call Select this option to answer another incoming call function may not be available depending on the model of the phone ENDING A CALL To finish the call perform one of the following procedures Hang up key on the Call in Finish the call Progress Display button on the steer F
128. AN VEHICLE IMMOBILIZER SYSTEM The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key If the engine fails to start using a registered key for example when interference is caused by another registered key an automated toll road device or automatic payment device on the key ring restart the engine using the following pro cedures 1 Leave the ignition switch placed in the ON position for approximately 5 seconds 2 Place the ignition switch in the OFF or LOCK position and wait approximately 10 seconds 3 Repeat steps 1 and 2 4 Restart the engine while holding the device which may have caused the interference separate from the registered key If the no start condition re occurs NISSAN rec ommends placing the registered key on a sepa rate key ring to avoid interference from other devices FCC Notice For USA This device complies with part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation NOTE Changes or modifications not expressly ap proved by the party responsible for compli ance could void the user s authority to op erate the equipment For Canada This device complies with RSS 210 of In dustry Canada Operation is subject to the following tw
129. ARNING Do not allow wet seat belts to roll up in the retractor NEVER use bleach dye or chemical solvents to clean the seat belts since these materials may severely weaken the seat belt webbing 7 6 Appearance and care CORROSION PROTECTION MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION The accumulation of moisture retaining dirt and debris in body panel sections cavities and other areas Damage to paint and other protective coat ings caused by gravel and stone chips or minor traffic accidents ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture Accumulation of sand dirt and water on the ve hicle body underside can accelerate corrosion Wet floor coverings will not dry completely inside the vehicle and should be removed for drying to avoid floor panel corrosion Relative humidity Corrosion will be accelerated in areas of high relative humidity especially those areas where the temperatures stay above freezing and where atmospheric pollution exists and road salt is used Temperature High temperatures accelerate the rate of corro sion to those parts which are not well ventilated Air pollution Industrial pollution the presence of salt in the air in coastal areas or heavy road salt use acceler ates the corrosion process Road salt also accel erates the disintegration of paint surfaces TO PROTECT YOUR VEHICLE FROM CORROSION Wash and wax your vehicle often to keep the v
130. AUX gt Menu Display Mode Display AUX settings Select the Settings key using the NISSAN con troller The display mode can be set to Normal Wide or Cinema The volume setting can be set to Low Medium or High Additional features For more information about the iPod player available with this system see iPod player operation with Navigation System in this section For more information about the USB interface available with this system see USB interface models with Navigation System in this section For more information about the Bluetooth streaming audio feature available with this sys tem see Bluetooth streaming audio in this section DIGITAL VERSATILE DISC DVD PLAYER OPERATION models with Navigation System Precautions Start the engine when using the DVD entertain ment system Movies will not be shown on the front display while the vehicle Is in any drive position to reduce driver distraction Audio is available when a movie is played To view movies on the front display stop the vehicle in a safe location move the shift lever to the P Park position and apply the park ing brake AWARNING The driver must not attempt to operate the DVD system or wear the head phones while the vehicle is in motion so that full attention may be given to ve hicle operation Do not attempt to modify the system to display a movie on the front screen while the vehicle
131. CD being played Song title displays the title of the selected CD track MP3 display mode To change the text displayed when listening to a CD with MP8s and ID3 tags press the DISP CLOCK button The DISP CLOCK button will scroll through the CD text as follows Disc number Track number and Folder number gt Folder title Song title Artist name gt Album title Disc number displays the number of the current disc playing Track number displays the number of the track playing on the selected disc Folder number displays the number of the current folder on the MP3 CD Folder title displays the title of the folder Song title displays the title of the song playing Artist name displays the name of the artist of the song playing Album title displays the title of the album of the song playing FM AM radio operation FM AM band select Pressing the AM FM button will change the band as follows AM FM1 FM2 AM When the AM FM button is pressed while the ignition switch is in the ACC or ON position the radio will come on at the station last played The last station played will also come on when the VOL ON OFF control knob is pressed ON If a compact disc is playing when the AM FM button is pressed the compact disc will auto matically be turned off and the last radio station played will come on The FM stereo indicator ST will illuminate during FM stereo reception When the
132. CH POSITIONS LOCK Normal parking position The ignition switch can only be locked in this position The ignition switch will be unlocked when it is pushed to the ACC position while carrying the Intelligent Key or with the Intelligent Key inserted in the port The ignition switch will lock when any door is opened or closed with the ignition switched off OFF The ignition switch is in the OFF position when the engine Is turned off using the ignition switch No lights will illuminate on the ignition switch ACC Accessories This position activates electrical accessories such as the radio when the engine is not running ACC has a battery saver feature that will turn the ignition switch to the OFF position after 30 min utes under the following conditions all doors are closed shift lever is in P Park The battery saver feature will be cancelled if any of the following occur any door is opened shift lever is moved out of P Park ignition switch changes position ON Normal operating position This position turns on the ignition system and electrical accessories A CAUTION Do not leave the vehicle with the ignition switch in ACC or ON positions when the engine is not running for an extended pe riod This can discharge the battery EMERGENCY ENGINE SHUT OFF To shut off the engine in an emergency situation while driving perform the following procedure Rapidly push the push
133. D WEIGHTS Overall length Overall width Overall height Front Track 18 inch tire 19 inch tire Rear Track 18 inch tire 19 inch tire Wheelbase Gross vehicle weight rating Gross axle weight rating Front Rear in mm in mm in mm in mm in mm in mm in mm in mm Ib kg Ib kg Ib kg 190 6 4 843 73 2 1 860 57 9 1 472 62 4 1 585 62 4 1 585 62 4 1 585 62 4 1 585 109 3 2 775 See the F M V S S C M V S S certification label on the center pillar between the driver s side front and rear doors WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve hicle in another country you should first find out if the fuel available is suitable for your vehi cle s engine Using fuel with an octane rating that is too low may cause engine damage All gasoline vehicles must be operated with unleaded gasoline There fore avoid taking your vehicle to areas where appropriate fuel is not available When transferring the registration of your vehicle to another country state province or district it may be necessary to modify the vehicle to meet local laws and regulations The laws and regulations for motor vehicle emis sion control and safety standards vary according to the country state province or district there fore vehicle specifications may differ When any vehicle is to be taken into an other country state provinc
134. Disc Random 1 Folder Random All Disc Repeat All Disc Repeat All discs loaded will be re peated 1 Disc Repeat The disc that is currently playing will be repeated 1 Track Repeat The track that is currently playing will be repeated 1 Folder Repeat The folder that is currently being accessed will be repeated All Disc Random All discs loaded will be played in a mixed order 1 Disc Random The tracks on the disc that is currently playing will be played in a mixed order 1 Folder Random The tracks in the folder that is currently being accessed will be played in a mixed order SCAN button While listening to a CD press the SCAN button to preview the first 10 seconds of each track on the CD playing Pressing the SCAN button again during this 10 second period stops the scan and the CD remains on that track CD EJECT Current Selected disc Pressthe amp button then press the slot number 1 6 for the desired disc The compact disc will be ejected If no slot num ber 1 6 is pressed the current loaded disc will be ejected If the ejected disc is not removed within 15 seconds the disc will reload All discs Press and hold the amp button for more than 1 5 seconds The compact discs will be ejected one by one If a disc is not removed within 15 seconds or the amp button is pressed again during the eject sequence the entire disc eject sequence will be can celed When this butt
135. E a 5 28 Draining of coolant water ssssssss eraann 5 28 Tire equipment ect tects cry ceed eeceenuaces 5 28 Special winter equipment 2 002 0e 5 28 Driving ON SNOW OF ICG sencuceuteeceres da seehcas 5 28 Engine block heater if so equipped 5 29 PRECAUTIONS WHEN STARTING AND DRIVING AWARNING e Do not leave children or adults who would normally require the assistance of others alone in your vehicle Pets should also not be left alone They could accidentally injure themselves or others through inadvertent operation of the vehicle Also on hot sunny days temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals e Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in jured Keep the car locked with the rear seatback and trunk lid securely latched when not in use and prevent children s access to car keys EXHAUST GAS carbon monoxide AWARNING e Do not breathe exhaust gases they contain colorless and odorless carbon monoxide Carbon monoxide is danger ous It can cause unconsciousness or death 5 2 Starting and driving If you suspect that exhaust fumes are entering the vehicle drive with all win dows fully open and have the vehicle inspected immediately e Do not run the engine in closed spaces such
136. ENER EENE eas 9 7 S E E E E E etre E P 9 7 Wheels and tires 0 0 cece eee eens 9 8 Dimensions and weights 2 2 0 9 8 When traveling or registering your vehicle in another COUNUY caverns cpecuactstaseeyceeseyecssen 9 9 Vehicle identification 0 0 00 cece eee ees 9 9 Vehicle identification number VIN plate 9 9 Vehicle identification number chassis number 000s 9 9 Engine serial number 2 022 005 9 10 F M V S S C M V S S certification label 9 10 Emission control information label 9 10 Tire and loading information label 9 11 Air conditioner specification label 9 11 Installing front license plate 9 11 Vehicle loading information 22005 9 12 TOWMSes eceaceauereee ete aces ee E E E as 9 12 Vehicle load capacity 0 02 eee eee 9 13 Loading TIS caveecdcercccee Pees cee ereeare ese 9 15 Measurement of weights 2 00 5 9 15 TOWING a traller srest entest ennhan near heudeee ened 9 16 Maximum load IES 2 2 stecnce dine dadaiceete geet 9 16 Towing load specification c224 c2020 sntseeesene 9 19 TOWING Sale 3 gece errena dreara aN 9 19 Fat TOWING 60s eee ccn tue eer et eeexeeeene saan 9 23 Uniform tire quality grading 222s lt edatewes este ks 9 24 Emission control system warranty 9 24 Reporting safety defects
137. ER SEAT ADJUSTMENT Operating tips The power seat motor has an auto reset overload protection circuit If the motor stops during operation wait 30 seconds then reactivate the switch Do not operate the power seat switch for a long period of time when the engine is off This will discharge the battery See Automatic drive positioner in Pre driving checks and adjustments for automatic drive po sitioner operation Forward and backward Moving the switch forward or backward will slide the seat forward or backward to the desired position Reclining Move the recline switch backward until the de sired angle is obtained To bring the seatback forward again move the switch forward and move your body forward The seatback will move forward The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit See Precautions on seat belt usage later in this section Also the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the shift lever is in P Park Safety Seats seat belts and supplemental restraint system 1 3 LRS0862 Seat lifter driver s seat Manual if so equipped Push the front or rear end of the switch up or Lumbar support driver s seat down to adjust the angle and height of the seat The lumbar support feature provides adjustable cushion lower back support to the dri
138. FF button MODE manual air flow control button button gt Fresh air intake button Temperature control buttons passen ger s side DUAL passenger s side temperature control ON OFF button Ut rear window defroster button 7 fan speed control dial ON OFF button 8 7 front defroster button ata a a gt 4 32 Monitor climate audio phone and voice recognition systems AUTO automatic climate control ON AWARNING The air conditioner cooling function op erates only when the engine is running e Do not leave children or adults who would normally require the assistance of others alone in your vehicle Pets should also not be left alone They could accidentally injure themselves or others through inadvertent operation of the vehicle Also on hot sunny days temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals e Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up Start the engine and operate the controls to activate the air conditioner NOTE Odors from inside and outside the vehicle can build up in the air conditioner unit Odor can enter the passenger compartment through the vents When parking set the heater and air condi tioner controls to turn off air recirculation to allow fresh air into the passenger compart ment This should help
139. Features and equipment in your vehicle may vary depend ing on model trim level options selected order date of production region or availability There fore you may find information about features or equipment that are not included or installed on your vehicle All information specifications and illustrations in this manual are those in effect at the time of print ing NISSAN reserves the right to change specifi cations performance design or component sup pliers without notice and without obligation From time to time NISSAN may update or revise this manual to provide Owners with the most accurate information currently available Please carefully read and retain with this manual all revision up dates sent to you by NISSAN to ensure you have access to accurate and up to date information re garding your vehicle Current versions of vehicle Owner s Manuals and any updates can also be found in the Owner section of the NISSAN website at https owners nissanusa com nowners navigation manualsGuide If you have questions concerning any information in your Owner s Manual contact NISSAN Consumer Affairs See the NISSAN CUSTOMER CARE PROGRAM page in this Owner s Manual for contact informa tion IMPORTANT INFORMATION ABOUT THIS MANUAL You will see various symbols in this manual They are used in the following ways AWARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury
140. Have the system checked by a NISSAN dealer No changes should be made to the seat belt system For example do not modify the seat belt add material or install devices that may change the seat belt routing or tension Doing so may affect the operation of the seat belt system Modifying or tampering with the seat belt system may result in serious per sonal injury e Once a seat belt pretensioner has acti vated it cannot be reused and must be replaced together with the retractor See your NISSAN dealer Removal and installation of preten sioner system components should be done by a NISSAN dealer All seat belt assemblies including re tractors and attaching hardware should be inspected after any collision by a NISSAN dealer NISSAN recommends that all seat belt assemblies in use dur ing a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly Seat belt assemblies not in use during a collision should also be inspected and replaced if either dam age or improper operation is noted All child restraints and attaching hard ware should be inspected after any col lision Always follow the restraint manufacturer s inspection instructions and replacement recommendations The child restraints should be replaced if they are damaged Safety Seats seat belts and supplemental restraint system 1 17 PREGNANT WOMEN NISSAN recommends that pregnant women use sea
141. ING The seat belts the side air bags and curtain air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor The side air bag and curtain air bag inflate with great force Do not allow anyone to place their hand leg or face near the side air bag on the side of the seatback of the front seat or near the side roof rails Do not allow anyone sitting in the front seats or rear outboard seats to Do not lean against the door extend their hand out of the window or lean against the door Some examples of dangerous riding positions are shown in the previous illustrations A WARNING e When sitting in the rear seat do not hold onto the seatback of the front seat If the side air bag inflates you may be seriously injured Be especially careful with children who should always be properly restrained Some examples of dangerous riding positions are shown in the illustrations e Do not use seat covers on the front seatbacks They may interfere with side air bag inflation Safety Seats seat belts and supplemental restraint system 1 47 1 48 Safety Seats seat belts and supplemental restraint system Roof mounted curtain side impact supplemental air bag inflators Roof mounted curtain side impact supplemental air bags Front seat mounted side impact supplemental air bag modules Air bag Control Unit ACU Supplemental front impact air bag mod ules Crash zone sens
142. Information Audio with Climate Control Information Audio with Turn Information for Navigation 8 00 Information Fuel Economy Weather Info Maintenance Map Update Where am 1 Navigation Version Traffic Info Others Show distance to empty and fuel economy HOW TO USE THE INFO BUTTON Press the INFO button This screen sets or dis plays various information that is helpful for using the vehicle Available items include fuel economy maintenance navigation and voice recognition information Monitor climate audio phone and voice recognition systems 4 15 Fuel Economy Displays Fuel Economy menu Distance to Empty Displays an estimation of the distance that the vehicle can be driven before refueling The DTE is constantly calculated based on the amount of fuel in the fuel tank and actual fuel consumption The display is updated every 30 seconds When the fuel level is low the DTE display will change to NOTE If the amount of fuel added while the ignition switch is OFF is small the display just before the ignition switch is turned OFF may continue to be displayed NOTE When driving uphill or rounding curves the fuel in the tank shifts which may momentarily change the display Average Fuel Econom Displays the average fuel economy since the last reset The display is updated every 30 seconds and 1 3 mi 500 m After a y y y i y y reset or connecting the battery cables the display might show Select R
143. It displays such items as Intelligent Key operation information some indicators and warnings other information For details about the Intelligent Key see NISSAN Intelligent Key in the Pre driving checks and adjustments section Instruments and controls 2 17 WIC1406 HOW TO USE THE VEHICLE INFORMATION DISPLAY Press the button located on the instru ment panel just behind the steering wheel to display the following modes MPG MPG MPH Time Miles Range Tire Pressure Exterior Temperature Setting Warning 2 18 Instruments and controls AVG 18 1 MPG Fuel economy mode The fuel economy mode can be selected to dis play the instant fuel economy since the last reset Average speed mode The average speed mode can be selected to display the average miles per gallon and miles per hour since the last reset TIME 20 38 333 3 miles Time Miles km mode The time miles km mode can be selected to show the time and distance driven since the last reset 21 miles Range mode The range mode can be selected to give you an estimation of the distance that can be driven before refueling The range is constantly calcu lated based on the amount of fuel in the fuel tank and the actual fuel consumption TIRE PRESSURES PSI kkk kkk kkk kkk Tire pressure mode The tire pressure mode displays the tire pressure information for your tires in the area of the
144. LE CONTINUOUSLY VARIABLE TRANSMISSION CVT A WARNING Do not depress the accelerator pedal while shifting from P Park or N Neu tral to R Reverse D Drive Ds Drive Sport or M Manual shift mode Al ways depress the brake pedal until shifting is completed Failure to do so could cause you to lose control and have an accident Cold engine idle speed is high so use caution when shifting into a forward or reverse gear before the engine has warmed up Do not downshift abruptly on slippery roads This may cause a loss of control Never shift to P Park or R Reverse while the vehicle is moving This could cause an accident Except in an emergency do not shift to the N Neutral position while driving Coasting with the transmission in the N Neutral position may cause serious damage to the transmission A CAUTION When stopping the vehicle on an uphill grade do not hold the vehicle by depress ing the accelerator pedal The foot brake should be used for this purpose The CVT in your vehicle is electronically con trolled to produce maximum power and smooth operation The CVT can operate in two different automatic drive modes D Drive mode Move the shift lever to D Drive the transmission is in the normal forward automatic driving mode The posi tion indicator in the meter shows a D The D Drive mode does not produce a gear change sensation like a traditional automatic transmissi
145. Link later in this section Instruments and controls 2 53 AWARNING e Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety stop and re verse features as required by federal safety standards These standards be came effective for opener models manufactured after April 1 1982 A ga rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse does not meet current federal safety standards Using a garage door opener without these features in creases the risk of serious injury or death e During the programming procedure your garage door or security gate will open and close if the transmitter is within range Make sure that people or objects are clear of the garage door gate etc that you are programming Your vehicle s engine should be turned off while programming the HomeLink Universal Transceiver 2 54 Instruments and controls PROGRAMMING HOMELINK If you have any questions or are having difficulty programming your HomeLink buttons refer to the HomeLink web site at www homelink com or call 1 800 355 3515 NOTE Place the ignition switch in the ACC posi tion when programming Home Link It is also recommended that a new battery be placed in the hand held transmitter of the device being programmed to HomeLink for quicker programming and accurate transmission of the radio frequency
146. M AM band select Pressing the FM AM button will change the band as follows AM FM1 FM2 AM When the FM AM button is pressed while the ignition switch Is in the ACC or ON position the radio will come on at the station last played The last station played will also come on when the VOL ON OFF control knob is pressed ON If a compact disc is playing when the FM AM button is pressed the compact disc will auto matically be turned off and the last radio station played will come on The FM stereo indicator ST will illuminate during FM stereo reception When the stereo broadcast signal is weak the radio will automatically change from stereo to monaural reception XM band select Pressing the AUX button will change the band as follows USB XM1 XM2 XM3 AUX USB satellite if so equipped When the AUX button is pressed while the igni tion switch is in the ACC or ON position the radio will come on at the station last played The last station played will also come on when the VOL ON OFF control knob is pressed ON When the AUX button is pressed the satellite radio mode will be skipped unless an optional satellite receiver and antenna are installed and a SiriusXM Satellite Radio service subscription is active Satellite radio is not available in Alaska Hawaii and Guam If a compact disc is playing when the AUX button is pressed the compact disc will automatically be turned off and t
147. N Long Life Antifreeze Coolant blue or equivalent may damage the engine cooling system The life expectancy of the factory fill coolant is 105 000 miles 168 000 km or 7 years Mixing any other type of cool ant other than Genuine NISSAN Long Life Antifreeze Coolant blue includ ing Genuine NISSAN Long Life Antifreeze Coolant green or the use of non distilled water will reduce the life expectancy of the factory fill cool ant Refer to the NISSAN Service and Maintenance Guide for more details CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold If the coolant level is below the MIN level add coolant to the MAX level A If the reservoir is empty check the coolant level in the radiator when the engine is cold If there is insufficient coolant in the radiator fill the radiator with coolant up to the filler opening and also add it to the reservoir up to the MAX level This vehicle contains Genuine NISSAN Long Life Antifreeze Coolant blue The life expectancy of the factory fill coolant is 105 000 miles 168 000 km or 7 years Mixing any other type of coolant or the use of non distilled water will re duce the life expectancy of the factory fill coolant Refer to the NISSAN Service and Maintenance Guide for more details If the cooling system frequently requires coolant have it checked by a NISSAN dealer CHANGING ENGINE COOLANT A NISSAN dealer can change
148. N vehicle immobilizer system 2 27 3 3 5 10 NISSAN voice recognition system 4 116 O Octane rating See fuel octane rating 9 4 Odometer s sa seara tim en baa due aa 2 5 Oil Capacities and recommended fuel lubricants ooa a 9 2 Changing engine oil 8 11 Changing engine oilfilter 8 12 Checking engine oillevel 8 10 Engine oil a aa aaa a 8 10 Engine oil and oil filter recommendation 9 5 Engine oil viscosity was a a a ewe we 9 6 Outside mirror control 3 28 Outside mirrors 24 6 ie ite Bm ew a ye od 3 28 Overheat If your vehicle overheats 6 10 Owner s manual order form 9 26 Owner s manual service manual order information lt ss ss de a we we de ok ew 9 26 Pp Parking Parking brake operation 5 18 Parking parking onhills 5 23 Phone Bluetooth hands free system 4 92 4 106 Power Power door locks 3 5 Power outlet g Gaw be ewes de ae 2 39 Power rear windows 2 45 Power steering fluid 8 13 Power steering system 5 24 Power WINDOWS 6 s 4 6 eee 6 ow we 2 44 Rear power windows 2 45 Precautions Maintenance precautions 8 5 Precautions on child restraints 1 25 1 31 1 36 1 40 Precautions on seat belt usage 1 16 Precautions on supplemental restraint SYSTEM a oe Se auc a a WS ate ee ee ae 1 43 Pre
149. Power rear windows 2 45 Power windows 244 2 44 Rear power windows 2 45 Windshield washer fluid 8 14 Windshield wiper and washer switch 2 28 Wiper Windshield wiper and washer switch 2 28 Wiper blades 0s 64 2 ts ee ah 4 8 20 10 7 GAS STATION INFORMATION RECOMMENDED FUEL NISSAN recommends the use of unleaded pre mium gasoline with an octane rating of at least 91 AKI Anti Knock Index number Research octane number 96 If unleaded premium gaso line is not available you may use unleaded regu lar gasoline with an octane rating of at least 87 AKI number Research octane number 91 but you may notice a decrease in performance A CAUTION Using a fuel other than that specified could adversely affect the emission control system and may also affect the warranty coverage Under no circumstances should a leaded gasoline be used because this will damage the three way catalyst Do not use E 15 or E 85 fuel in your vehicle Your vehicle is not designed to run on E 15 E 85 fuel Using E 15 or E 85 fuel in a vehicle not specifically de signed for E 15 or E 85 fuel can ad versely affect the emission control de vices and systems of the vehicle Damage caused by such fuel is not cov ered by the NISSAN new vehicle limited warranty U S government regulations require ethanol dispensing pumps to be identi fied by a small square orange and b
150. SINGLE HOMELINK BUTTON To reprogram a HomeLink Universal Trans ceiver button complete the following 1 Press and hold the desired HomeLink but ton DO NOT release the button 2 The indicator light will begin to flash after 20 seconds Without releasing the HomeLink button proceed with Pro gramming HomeLink Step 1 For questions or comments contact HomeLink at www homelink com or 1 800 355 3515 except Mexico The HomeLink Universal Transceiver button has now been reprogrammed The new device can be activated by pushing the HomeLink button that was just programmed This procedure will not affect any other programmed HomeLink buttons IF YOUR VEHICLE IS STOLEN If your vehicle is stolen you should change the codes of any non rolling code device that has been programmed into HomeLink Consult the Owner s Manual of each device or call the manu facturer or dealer of those devices for additional information When your vehicle is recovered you will need to reprogram the HomeLink Univer sal Transceiver with your new transmitter information FCC Notice For USA This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation NOTE Changes or modifications not expressl
151. SSAN controller to select an item and then press the ENTER button When the amber indicator next to an item is illuminated the feature is enabled 4 8 Monitor climate audio phone and voice recognition systems See Audio system in this section for more information Display Adjusts the settings for the display screen Brightness Contrast Adjusts the brightness or contrast of the map background Display off Toggles the display screen on and off The amber indicator is illuminated when the display is set to On When the display is set to Off anda control panel audio or heater and air conditioner button is pressed the display will resume until that operation is finished To turn the display back on press and hold the W OFF button for approximately 2 seconds or return to the display setting screen and adjust the setting Background Color Adjusts the display screen between day and night mode Switch Beeps Toggles on and off the beep sound that is heard when a control panel button is pressed Camera Toggles the predictive course lines on or off when the rear view camera is displayed on screen See RearView Monitor in this section for more information Toggles on or off the clock in the upper right corner of the display Toggles between a 12 hour and 24 hour clock Toggles on or off the daylight savings time Adjusts the time zone Choose a time zone form the available list Manually adjusts the hours and minutes of th
152. Troubleshooting guide Symptom Cause and Countermeasure Check if the CD USB device was inserted correctly Check if the CD is scratched or dirty Check if there is condensation inside the player If there is wait until the condensation is gone about 1 hour before using the player If there is a temperature increase error the player will play correctly after it returns to the normal temperature If there is a mixture of music CD files CD DA data and compressed audio files on a CD only the music CD files CD DA data will be played Cannot play Files with extensions other than MP3 or WMA cannot be played In addition the character codes and number of characters for folder names and file names should be in compliance with the specifications Check if the disc or file is generated in an irregular format This may occur depending on the variation or the setting of the compressed audio file writ ing application or other text editing applications Check if the finalization process such as session close and disc close is done for the disc Check if the CD USB device is protected by copyright Poor sound quality Check if the CD is scratched or dirty It takes a relatively long time If there are many folders or file levels on the CD USB device or if it is a multisession disc some time may be required before the music starts playing before the music starts playing The writing software and hardware combination might n
153. V S S certification label 2 Weigh your vehicle on the scale with all of the passengers and cargo that are normally in the vehicle when towing a trailer 3 Subtract the actual vehicle weight from the GVWR The remaining amount is the avail able maximum tongue load To determine the Gross Trailer Weight weigh your trailer on a scale with all equipment and cargo that are normally in the trailer when it is towed Make sure the Gross Trailer Weight is not more than the Gross Trailer Weight Rating shown on the trailer and is not more than the calculated available maximum towing capacity Also weigh the front and rear axles on the scale to make sure the Front Gross Axle Weight and Rear Gross Axle Weight are not more than Front Gross Axle Weight and Rear Gross Axle Weight on the F M V S S C M V S S certification label The cargo in the trailer and vehicle may need to be moved or removed to meet the specified rat ings Example Gross Vehicle Weight GVW as weighed onascale including passengers cargo and hitch 4 446 lb 2016 kg Gross Vehicle Weight Rating GVWR from F M V S S C M V S S certification label 4 546 Ib 2062 kg Maximum Towing Load from Towing Load Specification chart 1 000 lb 454 kg 4 546 lb 2062 kg 4 446 lb 2016 kg GVWR GVW 100 Ib 45 kg Available for tongue weight 1 000 Ib 454 kg Capacity available for towing 100 Ib 45 kg Available tongue
154. Voice Recognition System For more information see NISSAN Voice Recognition System in this section Monitor climate audio phone and voice recognition systems 4 111 HANDSET PHONEBOOK Many phones will support an automatic down load of the cellular phone s phonebook Since this method allows for up to 1000 numbers to be stored and entries are automatically assigned voice tags by the system this is a useful function for easy dialing supported by the Voice Recogni tion system Settings gt Phone Go i Ful 8 00 Edit Vehicle Phonebook Delete Phonebook Download Handset Phonebook Volume amp Ringtone Auto Downloaded 1 5 Add or edit phonebook entries Transferring the handset phonebook If your cellular phone supports automatic down loading the system transfers the handset phone book automatically by default To ensure that this feature is activated press the SETTING button on the instrument panel and select the Phone key The Auto Downloaded selection should have the amber indicator next to the word ON activated Select the Auto Downloaded key to toggle this feature on or off 4 112 Monitor climate audio phone and voice recognition systems To transfer the handset phonebook to the vehicle manually follow these steps 1 Press the SETTING button on the control panel 2 Select the Phone key 3 Select the Download Handset Phonebook key Once the handset phonebook
155. Wiper Interval Selective Door Un When this item is turned on only the driver s door is unlocked first after the door unlock operation When the door handle request switch lock on the driver s or front passenger s side door is pushed to be unlocked only the corresponding door is unlocked first All the doors can be unlocked if the door unlock operation is performed again within one minute Intelligent Key Select to turn on or turn off the door lock unlock function by pushing the door handle request switch Lock Unlock Lift Steering Wheel Select to turn on or turn off the steering wheel moving upward for easy exit when the ignition switch is in the OFF position and the driver s on Exit door is opened After getting into the vehicle and placing the ignition switch in the ACC position the steering wheel moves to the previous position Slide Driver Seat Select to turn on or turn off the driver s seat moving backward for easy exit when the ignition switch is in the OFF position and the driver s Back on Exit door is opened After getting into the vehicle and placing the ignition switch in the ACC position the steering wheel moves to the previous position Return All Settings Select to change all the comfort systems to their default settings to Default a Language amp Units Adjusts the language and unit settings shown on the display 4 18 Monitor climate audio phone and voice recognition systems Select Language Changes the lan
156. a inlet port Doing so may entangle these Ignition switch is placed in the OFF posI objects in the screen when it is extend EEE tion ing or retracting causing improper op O00 9 The lights will go off when the ignition switch is in eration or damage to the screen the ON position or the driver s door is closed and e Do not push the sun shade arm with locked your hands etc as this may deform it Improper operation or damage to the screen may result The lights will also go off after a period of time when all doors are open Do not hang any object on the arm rail When the switch is in the OFF position 3 as this may result in improper operation the front and rear personal lights will not or damage the screen illuminate regardless of door position Do not forcefully pull the screen Doing The interior light has a three position switch and so may elongate the screen Improper operates regardless of ignition switch position operation or damage tothe screen may When the switch is in the ON position result fi tage the front and rear personal lights will illumi e To avoid personal injury keep your nate regardless of door position The light hands fingers and head away from the will go off after a period of time unless the A arm arm rail and screen inlet ignition switch is placed in the ON position port When the switch is in the center DOOR po sition 2 the front and rear personal
157. a 2 40 Sunroof see Moonroof 2 47 DUN VISCIS a se a e HOS A ee 3 25 Supplemental air bag warning light 1 57 2 14 Supplemental front impact air bag system 1 50 Supplemental restraint system Information and warning labels 1 57 Precautions on supplemental restraint SysteM wie ee tO ae Ae ee ee 1 43 Supplemental restraint system Supplemental air bag system 1 43 Switch Autolight switch 1 64 40 a amp ww amp 2 32 Automatic power window switch 2 46 Fog light switch 2 34 Hazard warning flasher switch 6 2 Headlight and turn signal switch 2 30 Headlight control switch 2 31 Power door lock switch 3 5 Rear window and outside mirror defroster SWiCNs oan ae a 08 wna ee eee 2 29 Turn signal switch ee vaso 8 oe ws 2 34 Vehicle dynamic control VDC off SWiCMs w s ew eed oo ee eee d 2 38 Windshield wiper and washer switch 2 28 T TACMOMGICE os amp wo wt ae ws eh ee Sy E 2 6 Temperature gauge Engine coolant temperature gauge 2 6 Theft NISSAN vehicle immobilizer system engine start 2 27 3 3 5 10 Three way catalyst aa ee 5 2 Tire FANTIG cd a wom ee Boh Me i an eile 6 3 Sparetire 2 ee 6 4 8 43 Tire and Loading Information label 9 11 Tire CHAINS 6 ou i ee ee we ee a 8 40 Tire placard 2 00000 9 11 Tire PIESSUG a e a e a we ee ow aoa 8 33 Tire rotation aoao 8 41 Types of tires
158. a anaa 5 11 Belt See drive belt aoaaa aaa 8 17 Block heater ENGINE sobre o e a eee ee ee 5 29 Bluetooth audio 4 85 Bluetooth hands free phone SVS aoaaa a a ee 4 92 4 106 Booster seats aoaaa a 1 40 Brake Anti lock Braking System ABS 5 25 Brake fluid 5212s ee ee ee De eas 8 13 Brake light See stop light 8 28 Brake system 004 5 24 Brake warning light 2 11 Brake wear indicators 2 16 8 21 Parking brake operation 5 18 Self adjusting brakes 8 21 Se Ce 8 21 Break in schedule 5 20 Brightness contrast button 4 10 4 19 Brightness control Instrument panel 2 34 Bulb check instrument panel 2 10 Bulb replacement 8 28 C Capacities and recommended fuel lubricants o oo 9 2 Cargo Nel a a a ea da a e e a 2 43 Cargo See vehicle loading information 9 12 Car phone or CBradio 4 91 CD care and cleaning 4 88 CD changer See audio system 4 54 CD player See audio system 4 60 4 67 Check tire pressure 2 2 ee ee 2 25 Child restraints 1 23 1 24 1 25 1 27 Precautions on child restraints 1 25 1 31 1 36 1 40 Top tether strap anchor point locations 1 29 Child safety reardoorlock 3 6 Chimes audible reminders 2 16 Cleaning exterior and interior 7 2
159. a de 2 7 Warning indicator lights and audible reminders 2 10 Checking DUDS cis ccawabeaeareeaseheoeebiss 2 10 Warming NOUS s2n22 enon tee ee cite eee pews we 2 10 indicator hoM S seres area caetaanens sete Seee dee 2 14 Audible reminders 0 000 c cece eee eens 2 17 Vehicle information display 0 022000 2 17 How to use the vehicle information display 2 18 Securty SVCIEMG eeren ranar ENRERE ARER NRR 2 26 Vehicle security system 0020022 eee 2 26 NISSAN vehicle immobilizer system 2 27 Windshield wiper and washer switch 2 28 Switch Operati n lt x dacasecag dae vera rtseee ni eoee 2 28 Rear window and outside mirror if so equipped deirosier SWC cc sasutsoseceennceeeieeseeee wanes 2 29 Headlight and turn signal switch 2 30 Xenon headlights if so equipped 2 30 Headlight control switch 2c0cacwacd ce wwadeleeiw ed 2 31 Daytime running light system Canada only 2 33 Instrument brightness control 005 2 33 TO SIONal SWIC wien certs ree on benter aie 2 34 Fog light switch if so equipped 6 2 34 FIOM 6 22666300 6006006 G00 64552 one deere daae dean eae 2 34 Heated seats if so equipped 0ee cece eee 2 35 Climate control seat switch if so equipped 2 36 Heated steering wheel if so equipped 2 37 Vehicle Dynamic Control VDC off switch 2 37 Powe
160. activate Alternate Command Mode A screen will appear prompting user to review the expanded command list and advises that some command will be replaced and voice menu prompts turned off User will have to confirm by pressing OK to proceed with activation Minimize Voice Feedback When Alternate Command Mode is activated this key will allow user to reduce system voice feedback during voice recognition session Monitor climate audio phone and voice recognition systems 4 133 Settings gt Voice Recognition 8 00 Change the mode of Voice Recognition SPEAKER ADAPTATION FUNCTION The Voice Recognition system has a function to learn the user s voice for better voice recognition performance The system can memorize the voices of up to three persons Having the system learn the user s voice 1 oF W N Press the SETTING button on the control panel Select the Others key on the display Select the Voice Recognition key Select the Speaker Adaptation key Select the user whose voice is to be memo rized by the system Select the Start Speaker Adaptation Learn ing key Select a category to be learned by the sys tem from the following list Phone Navigation Information Audio Help The voice commands in the category are displayed 4 134 Monitor climate audio phone and voice recognition systems 10 11 Press the amp Select a voice command to train T
161. ad Starting and driving 5 27 COLD WEATHER DRIVING FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing apply de icer through the key hole If the lock becomes frozen heat the key before inserting it into the key hole or use the remote keyless entry function on the Intelligent Key ANTI FREEZE In the winter when it is anticipated that the tem perature will drop below 32 F 0 C check the anti freeze to assure proper winter protection For details see Engine cooling system in the Maintenance and do it yourself section of this manual BATTERY If the battery is not fully charged during extremely cold weather conditions the battery fluid may freeze and damage the battery To maintain maxi mum efficiency the battery should be checked regularly For details see Battery in the Main tenance and do it yourself section of this manual 5 28 Starting and driving DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti freeze drain the cooling system including the engine block Refill before operating the vehicle For details see Changing engine coolant in the Maintenance and do it yourself section of this manual TIRE EQUIPMENT 1 SUMMER tires have a tread designed to provide superior performance on dry pave ment However the performance of these tires will be substantially reduced in snowy and icy conditions If you operate your ve hicle o
162. affect vehicle trailer handling possibly caus ing vehicle sway When being passed by larger vehicles be prepared for possible changes in crosswinds that could affect ve hicle handling Do the following if the trailer begins to sway 1 Take your foot off the accelerator pedal to allow the vehicle to coast and steer as straight ahead as the road conditions allow This combination will help stabilize the ve hicle Do not correct trailer sway by steering or applying the brakes When the trailer sway stops gently apply the brakes and pull to the side of the road ina safe area Try to rearrange the trailer load so it is bal anced as described earlier in this section Be careful when passing other vehicles Passing while towing a trailer requires con siderably more distance than normal pass ing Remember the length of the trailer must also pass the other vehicle before you can safely change lanes Downshift the transmission to a lower gear for engine braking when driving down steep or long hills This will help slow the vehicle without applying the brakes Avoid holding the brake pedal down too long or too frequently This could cause the brakes to overheat resulting in reduced braking efficiency Increase your following distance to allow for greater stopping distances while towing a trailer Anticipate stops and brake gradually NISSAN recommends that the cruise con trol not be used while towing a traile
163. age on the webbing is found the entire seat belt as sembly should be replaced 1 22 Safety Seats seat belts and supplemental restraint system CHILD SAFETY AWARNING Do not allow children to play with the seat belts Most seating positions are equipped with Automatic Locking Retrac tor ALR mode seat belts If the seat belt becomes wrapped around a child s neck with the ALR mode activated the child can be seriously injured or killed if the seat belt retracts and becomes tight This can occur even if the vehicle is parked Un buckle the seat belt to release the child If the seat belt cannot be unbuckled or is already unbuckled release the child by cutting the seat belt with a suitable tool such as a knife or scissors to release the seat belt Children need adults to help protect them They need to be properly restrained In addition to the general information in this manual child safety information is available from many other sources including doctors teachers government traffic safety offices and community organizations Every child is different so be sure to learn the best way to transport your child There are three basic types of child restraint systems Rear facing child restraint Forward facing child restraint Booster seat The proper restraint depends on the child s size Generally infants up to about 1 year and less than 20 Ibs 9 kg should be placed in rear facing child restraints For
164. ally 30 seconds or less The EDR in this vehicle is designed to record such data as How various systems in your vehicle were operating Whether or not the driver and passenger safety belts were buckled fastened How far if at all the driver was depressing the accelerator and or brake pedal and How fast the vehicle was traveling Sounds are not recorded These data can help provide a better understand ing of the circumstances in which crashes and injuries occur NOTE EDR data are recorded by your vehicle only if a nontrivial crash situation occurs no data are recorded by the EDR under normal driving conditions and no personal data e g name gender age and crash location are recorded However other parties such as law enforcement could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation To read data recorded by an EDR special equip ment is required and access to the vehicle or the EDR is needed In addition to the vehicle manu facturer and NISSAN dealer other parties such as law enforcement that have the special equip ment can read the information if they have ac cess to the vehicle or the EDR EDR data will only be accessed with the consent of the vehicle owner or lessee or as otherwise required or per mitted by law OWNER S MANUAL SERVICE MANUAL ORDER INFORMATION Genuine NISSAN Service Manuals for this model year and prior can
165. an Provinces your vehicle may be re quired to be in what is called the ready condi tion for an Inspection Maintenance I M test of the emission control system The vehicle is set to the ready condition when it is driven through certain driving patterns Usually the ready condition can be obtained by ordinary usage of the vehicle If a powertrain system component is repaired or the battery is disconnected the vehicle may be reset to a not ready condition Before taking the I M test check the vehicle s inspection maintenance test readiness condi tion Place the ignition switch in the ON position without starting the engine If the Malfunction Indicator Light MIL comes on steady for 20 sec onds and then blinks for 10 seconds the I M test condition is not ready If the MIL does not blink after 20 seconds the I M test condition is ready Contact a NISSAN dealer to set the ready condition or to prepare the vehicle for testing 9 26 Technical and consumer information EVENT DATA RECORDERS EDR This vehicle is equipped with an Event Data Re corder EDR The main purpose of an EDR is to record in certain crash or near crash like situa tions such as an air bag deployment or hitting a road obstacle data that will assist in understand ing how a vehicle s systems performed The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time typic
166. ance will be somewhat different than under normal driving conditions e Always secure items in the trailer to prevent load shift while driving Lock the trailer hitch coupler with a pin or lock to prevent the coupler from inadver tently becoming unlatched Avoid abrupt starts acceleration or stops Avoid sharp turns or lane changes Always drive your vehicle at a moderate speed Technical and consumer information 9 21 When backing up hold the bottom of the steering wheel with one hand Move your hand in the direction in which you want the trailer to go Make small corrections and back up slowly If possible have someone guide you when you are backing up Always block the wheels on both vehicle and trailer when parking Parking on a slope is not recommended however if you must do so A CAUTION If you move the shift selector to the P Park position before blocking the wheels and applying the parking brake transmission damage could occur iF 2 4 D 6 Apply and hold the brake pedal Have someone place blocks on the downhill side of the vehicle and trailer wheels After the wheel blocks are in place slowly release the brake pedal until the blocks ab sorb the vehicle load Apply the parking brake Shift the transmission into P Park Turn off the engine To drive away 1 9 22 Technical and consumer information Start the vehicle y O Apply and hold the brake pedal Shi
167. ands free phone Do not place the Bluetooth audio device in an area surrounded by metal or far away from the in vehicle Bluetooth module to prevent tone quality degradation and wireless con nection disruption While an audio device is connected through the Bluetooth wireless connection the battery power of the device may discharge quicker than usual This system supports the Bluetooth Audio Distribution Profile A2DP AVRCP BLUETOOTH is a trademark owned by Bluetooth SIG Inc and licensed to Clarion Co Ltd Bluetooth CD or USB with Compressed Audio Files models without Navigation System The file types supported by this system are MP3 and WMA Explanation of terms MP3 MP3 is short for Moving Pictures Experts Group Audio Layer 3 MP3 is the most well known compressed digital audio file format This format allows for near CD quality sound but at a fraction of the size of normal audio files MP3 conversion of an audio track from CD ROM can reduce the file size by approximately a 10 1 ratio with virtually no perceptible loss in quality MP3 compression removes the redundant and irrelevant parts of a sound signal that the human ear doesn t hear WMA Windows Media Audio WMA is a compressed audio format created by Micro soft as an alternative to MP3 The WMA codec offers greater file compression than the MP3 codec enabling storage of more digital audio tracks in the same am
168. ansmitter build ings bridges mountains and other external influ ences Intermittent changes in reception quality normally are caused by these external influences Using a cellular phone in or near the vehicle may influence radio reception quality Radio reception Your NISSAN radio system is equipped with state of the art electronic circuits to enhance ra dio reception These circuits are designed to extend reception range and to enhance the qual ity of that reception However there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle even when the finest equipment is used These char acteristics are completely normal in a given re ception area and do not indicate any malfunction in your NISSAN radio system Reception conditions will constantly change be cause of vehicle movement Buildings terrain signal distance and interference from other ve hicles can work against ideal reception De scribed below are some of the factors that can affect your radio reception Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers Storing the de vice in a different location may reduce or elimi nate the noise FM RADIO RECEPTION Range FM range is normally limited to 25 30 mi 40 48 km with monaural single channel FM having slightly more range than stereo FM Exter nal influenc
169. ard and check to see if the LATCH at tachment holds the restraint in place If the restraint is not secure tighten the LATCH attachment as necessary or put the restraint in another seat and test it again You may need to try a different child restraint Not all child restraints fit in all types of vehicles 7 Check to make sure the child restraint is properly secured prior to each use If the child restraint is loose repeat steps 1 through 6 FORWARD FACING CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS AWARNING The three point seat belt with Automatic Locking Retractor ALR must be used when installing a child restraint Failure to use the ALR mode will result in the child restraint not being properly secured The restraint could tip over or be loose and cause injury to a child in a sudden stop or collision Also it can change the operation of the front passenger air bag See Front passenger air bag and status light later in this section a WRS0699 Forward facing front passenger seat step 1 Refer to all Warnings and Cautions in the Child Safety and Child Restraints sections before installing a child restraint Follow these steps to install a forward facing child restraint using the vehicle seat belt in the rear seats or in the front passenger seat 1 If you must install a child restraint in the front seat it should be placed in a forward facing direction only Move the seat to the r
170. as a garage Do not park the vehicle with the engine running for any extended length of time Keep the rear vent windows lift gates doors and trunk lids if so equipped closed while driving otherwise exhaust gases could be drawn into the passen ger compartment If you must drive with one of these open follow these precautions 1 Open all the windows 2 Set the air recirculation but ton to off and the fan control dial to high to circulate the air If electrical wiring or other cable con nections must pass to a trailer through the seal on the trunk lid or the body follow the manufacturer s recommen dation to prevent carbon monoxide en try into the vehicle The exhaust system and body should be inspected by a qualified mechanic whenever a The vehicle is raised for service b You suspect that exhaust fumes are entering into the passenger compartment c You notice a change in the sound of the exhaust system d You have had an accident involving damage to the exhaust system un derbody or rear of the vehicle THREE WAY CATALYST The three way catalyst is an emission control device installed in the exhaust system Exhaust gases in the three way catalyst are burned at high temperatures to help reduce pollutants AWARNING The exhaust gas and the exhaust sys tem are very hot Keep people animals or flammable materials away from the exhaust system components e Do not st
171. aska Hawaii and Guam FM AM SAT RADIO WITH CD DVD E FOL os A aN PLAYER if so equipped FM AM SAT DISC AUX For all operation precautions see Audio opera tion precautions in this section SCAN nal i yah TRACK gt gt I SZ Audio main operation VOL ON OFF control Place the ignition switch in the ACC or ON position and push the VOL ON OFF control knob while the system is off to call up the mode that was playing immediately before the system was turned off To turn the system off press the VOL ON OFF control knob Is CD eject button 6 TRACK button Turn the VOL ON OFF control knob to adjust the 2 VOL ON OFF control knob 7 SEEK CAT button v lum 3 Station select 1 6 buttons 8 SAT button M 4 TUNE FOLDER and AUDIO control 9 RPT RDM button This vehicle has Speed Sensitive Volume SSV for audio The audio volume changes as the driv knob Bass Treble Fade and Balance 10 SCAN button ing speed changes 5 DISC AUX button 11 FM AM button Monitor climate audio phone and voice recognition systems 4 63 Audio settings Audio Adjusts the bass to the desired level Adjusts the treble to the desired level Adjusts the balance to the desired level Balance adjusts the sound level between the left and right speakers Adjusts the fade to the desired level Fader adjusts the sound level between the front and rear speakers Adjusts the speed sensitive volume function which increases the
172. at case reset the desired stations Radio data system RDS RDS stands for Radio Data System and is a data information service transmitted by some radio stations on the FM band not AM band Cur rently most RDS stations are in large cities but many stations are now considering broadcasting RDS data RDS can display Station call sign such as WHFR 98 3 Station name such as The Groove Music or programming type such as Clas sical Country or Rock Monitor climate audio phone and voice recognition systems 4 59 When the Text key is selected with the NISSAN controller on the display while the radio is playing additional information is displayed on the screen If the station broadcasts RDS information the RDS icon is displayed Compact disc CD player operation Place the ignition in the ACC or ON position and insert the compact disc into the slot with the label side facing up The compact disc will be guided automatically into the slot and start playing If the radio is already operating it will automati cally turn off and the compact disc will play If the system has been turned off while the com pact disc was playing pressing the VOL ON OFF control knob will start the compact disc DISC button When the DISC button is pressed with the sys tem off and a compact disc loaded the system will turn on and the compact disc will start to play When the DISC butt
173. ate and warn you of it by the low tire pressure warning light This system will activate only when the vehicle is driven at speeds above 16 MPH 25 km h For more details refer to Warning indicator lights and audible reminders in the Instruments and controls section and Tire Pressure Monitoring System TPMS in the Starting and driving section AWARNING e Radio waves could adversely affect electric medical equipment Those who use a pacemaker should contact the electric medical equipment manufac turer for the possible influences before use If the low tire pressure warning light illuminates while driving avoid sudden steering maneuvers or abrupt braking reduce vehicle speed pull off the road to a safe location and stop the vehicle as soon as possible Driving with under inflated tires may permanently damage the tires and increase the likelihood of tire failure Serious vehicle damage could occur and may lead to an accident and could result in serious personal in jury Check the tire pressure for all four tires Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Informa tion label to turn the low tire pressure warning light OFF If you have a flat tire replace it with a spare tire as soon as possible When a spare tire is mounted or a wheel is replaced tire pressure will not be indicated the TPMS will not function and the low tire pressure warning l
174. ated inside the trunk compart ment on the interior of the trunk lid SECONDARY TRUNK LID RELEASE if so equipped For models with a rear center console the trunk can be accessed through the access panel be tween the rear seats as shown To open the trunk lid from the rear seat Fold down the center arm rest Insert the mechanical key into the trunk com partment access lid lock Fold down the trunk compartment access lid For more in formation on the mechanical key see NISSAN Intelligent Key in this section Pull the rear seat trunk release handle 4 To close push the trunk lid down securely Pre driving checks and adjustments 3 19 FUEL FILLER DOOR WPD0454 OPENING THE FUEL FFILLER DOOR The fuel filler door automatically unlocks when the driver s door is unlocked 1 Unlock the fuel filler door using one of the following operations Unlock the driver s door with the keyfob Push the power door lock switch to the unlock position Push the door handle request switch 2 To open the fuel filler door push the right side of the fuel filler door to release 3 20 Pre driving checks and adjustments To lock close the fuel filler door securely and lock the doors NOTE The fuel filler door will unlock using the key only when all doors are unlocked Un locking the driver s door will not unlock the fuel filler door FUEL FILLER CAP AWARNING Gasoline is extreme
175. ately level with the center of the head restraint headrest lf your ear position is still higher than the recommended alignment place the head restraint headrest at the highest position Adjustable head restraint headrest Non adjustable head restraint lf the head restraint headrest has been re components headrest components moved ensure that it is reinstalled and locked in place before riding in that desig 1 Removable head restraint headrest 1 Removable head restraint headrest nated seating position 2 Multiple notches 2 Single Notch 3 Lock knob 3 Lock knob 4 Stalks 4 Stalks 1 8 Safety Seats seat belts and supplemental restraint system Removable Use the following procedure to remove the head restraints headrests 1 Pull the head restraint headrest up to the highest position Push and hold the lock knob 3 Remove the head restraint headrest from the seat Store the head restraint headrest properly in a secure place so it is not loose in the vehicle Reinstall and properly adjust the head restraint headrest before an occupant uses the seating position Install 1 Align the head restraint headrest stalks with the holes in the seat Make sure the head restraint headrest is facing the correct di rection The stalk with the notch notches 4 must be installed in the hole with the lock knob Push and hold the lock knob and the head restraint headrest down Prop
176. ator light also comes on when the passing signal is activated ENGINE Malfunction indicator light MIL If the malfunction indicator light comes on steady or blinks while the engine is running it may indi cate a potential emission control and or CVT malfunction ENGINE SOON The malfunction indicator light may also come on steady if the fuel filler cap is loose or missing or if the vehicle runs out of fuel Check to make sure the fuel filler cap is installed and closed tightly and that the vehicle has at least 3 gallons 11 4 li ters of fuel in the fuel tank SERVICE After a few driving trips the 88 light should turn off if no other potential emission control system malfunction exists If this indicator light comes on steady for 20 sec onds and then blinks for 10 seconds when the engine is not running it indicates that the vehicle is not ready for an emission control system inspection maintenance test See Readiness for inspection maintenance I M test in the Tech nical and consumer information section of this manual Operation The malfunction indicator light will come on in one of two ways Malfunction indicator light on steady An emission control system and or CVT mal function has been detected Check the fuel filler cap if the LOOSE FUEL CAP warning appears in the vehicle information display If the fuel filler cap is loose or missing tighten or install the cap and continue to drive
177. ause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation NOTE Changes or modification not expressly ap proved by the party responsible for compli ance could void the user s authority to op erate the equipment For Canada This device complies with RSS 210 of In dustry Canada Operation is subject to the following two conditions 1 This device may not cause interference and 2 this device must accept any interference in clude interference that may cause unde sired operation of the device AVOIDING COLLISION AND ROLLOVER AWARNING Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident Be alert and drive defensively at all times Obey all traffic regulations Avoid excessive speed high speed cornering or sudden steering maneuvers because these driving practices could cause you to lose control of your vehicle AS with any ve hicle loss of control could result in a colli sion with other vehicles or objects or cause the vehicle to roll over particularly if the loss of control causes the vehicle to slide side ways Be attentive at all times and avoid driving when tired Never drive when under the influence of alcohol or drugs including prescription or over the counter drugs which may cause drowsiness Always wear your seat belt as outlined in the Safety Seats
178. ause overheating The trans mission high fluid temperature protection mode which helps reduce the chance of transmission damage could activate and automatically de crease engine power Under some conditions engine and vehicle speed could be reduced Plan your trip carefully to account for trailer and vehicle load weather and road conditions AWARNING Overheating can result in reduced engine power and lower vehicle speed Also when the high temperature mode oper ates engine and vehicle speed may be gradually reduced On highways the re duced speed may be lower than other traf fic which could increase the chance of a collision Be especially careful when driv ing If the vehicle cannot maintain a safe driving speed pull to the side of the road in a safe area and allow the engine to cool or the transmission to return to normal operation See If your vehicle overheats in the In case of emergency section of this manual A CAUTION Vehicle damage resulting from improper towing procedures is not covered by NISSAN warranties Total trailer load Tongue load Tongue load x 100 10 to 15 Total trailer load Tongue load Keep the tongue load between 10 15 percent of the total trailer load or use the trailer tongue load specified by the trailer manufacturer The tongue load must be within the maximum tongue load limits shown in the following Towing Load Specification chart If the tongue load be
179. bag and curtain air bag systems This is to prevent damage to or accidental inflation of the side air bag and curtain air bag or damage to the side air bag and curtain air bag systems Do not make unauthorized changes to your vehicle s electrical system sus pension system or side panel This could affect proper operation of the side air bag and curtain air bag system Tampering with the side air bag system may result in serious personal injury For example do not change the front seats by placing material near the seat backs or by installing additional trim material such as seat covers around the side air bag Work around and on the side air bag and curtain air bag systems should be done by a NISSAN dealer Installation of electrical equipment should also be done by a NISSAN dealer The SRS wir ing harnesses should not be modified or disconnected Unauthorized electri cal test equipment and probing devices should not be used on the side air bag or curtain air bag system The SRS wiring harness connectors are yellow and orange for easy identification When selling your vehicle we request that you inform the buyer about the side air bag and curtain air bag systems and guide the buyer to the appropriate sections in this Owner s Manual Seat belts with pretensioners front seats AWARNING The pretensioners cannot be reused af ter activation They must be replaced together with the retractor and buckle as a u
180. be placed in a rear facing child restraint NISSAN recom mends that infants be placed in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards You should choose a child restraint that fits your vehicle and always follow the manu facturer s instructions for installation and use SMALL CHILDREN Children that are over 1 year old and weigh at least 20 lbs 9 kg should remain in a rear facing child restraint as long as possible up to the height or weight limit of the child restraint Children who outgrow the height or weight limit of the rear facing child restraint and are at least 1 year old should be secured in a forward facing child re straint with a harness Refer to the manufactur er s instructions for minimum and maximum weight and height recommendations NISSAN recommends that small children be placed in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Ve hicle Safety Standards You should choose a child restraint that fits your vehicle and always follow the manufacturer s instructions for instal lation and use LARGER CHILDREN Children should remain in a forward facing child restraint with a harness until they reach the maxi mum height or weight limit allowed by the child restraint manufacturer Safety Seats seat belts and supplemental restraint system 1 23 Once a child outgrows the height or weight limit of t
181. before using the player If there is a temperature increase error the player will play correctly after it returns to the normal temperature If there is a mixture of music CD files CD DA data and compressed audio files on a CD only the music CD files CD DA data will be played Cannot play Files with extensions other than MP3 WMA AAC M4A or AA3 cannot be played In addition the character codes and number of charac ters for folder names and file names should be in compliance with the specifications Check if the disc or file is generated in an irregular format This may occur depending on the variation or the setting of the compressed audio file writ ing application or other text editing applications Check if the finalization process such as session close and disc close is done for the disc Check if the CD DVD USB device is protected by copyright Poor sound quality Check if the CD DVD is scratched or dirty It takes a relatively long time If there are many folders or file levels on the CD DVD USB device or if it is a multisession disc some time may be required before the music starts before the music starts playing playing The writing software and hardware combination might not match or the writing speed writing depth writing width etc might not match the Music cuts off or skips bee ae me specifications Try using the slowest writing speed Skipping with high bit rate Skipping may occur
182. below the MINIMUM or MIN mark on the brake fluid reservoir do not drive until the brake system has been checked at a NISSAN dealer Anti lock Braking System ABS warning indicator When the parking brake is released and the brake fluid level is sufficient if both the brake warning light and the Anti lock Braking System ABS warning light illuminate it may indicate the ABS is not functioning properly Have the brake system checked and if necessary repaired by a NISSAN dealer promptly Avoid high speed driv ing and abrupt braking See Anti lock Braking System ABS warning light in this section Charge warning light If this light comes on while the engine is running it may indicate the charging system is not func tioning properly Turn the engine off and check the generator belt If the belt is loose broken missing or if the light remains on see a NISSAN dealer immediately Instruments and controls 2 11 A CAUTION e Do not ground electrical accessories di rectly to the battery terminal Doing so will bypass the variable control system and the vehicle battery may not charge completely Refer to Variable voltage control system if so equipped in the Maintenance and do it yourself sec tion later in this manual Do not continue driving if the generator belt is loose broken or missing ry Engine oil pressure warning light This light warns of low engine oil pressure If the light flic
183. bjects can injure you in an accident To open the front cup holders push the cup holder lid To close lower the cup holder lid and push down until it clicks in place 2 40 Instruments and controls The rear cup holders are located in the fold down armrest in the rear seat back LIC0423 Rear To open the cup holders on the rear fold down armrest lift the cup holder lid To close lower the lid WIC1216 Soft bottle holder Soft bottle holder A CAUTION Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident Do not use bottle holder for open liquid containers GLOVE BOX Open the glove box by pulling the handle Use the mechanical key when locking 4 or unlocking the glove box AWARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop CONSOLE BOX Upper half Pull up on the driver s side latch to open the upper half of the console box The upper half of the console box may be used for storage of cellular phones An access hole is provided at the front of the upper half of the console box for a phone or iPod cord routing to the power outlet Instruments and controls 2 41 LICO748 Lower half GROCERY HOOKS CARGO NET if so equipped Pull up on the passenger s side latch to open the The grocery hooks are located in the trunk and WARNING lower
184. brak ing distances This may cause a premature tire failure which could result in a serious accident and personal injury Failures caused by overloading are not covered by the vehicle s warranty MEASUREMENT OF WEIGHTS Secure loose items to prevent weight shifts that could affect the balance of your vehicle When the vehicle is loaded drive to a scale and weigh the front and the rear wheels separately to determine axle loads Individual axle loads should not ex ceed either of the gross axle weight rat ings GAWR The total of the axle loads should not exceed the gross vehicle weight rating GVWR These ratings are given on the vehicle certification label If weight ratings are exceeded move or re move items to bring all weights below the ratings Technical and consumer information 9 15 TOWING A TRAILER AWARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling braking and perfor mance and may lead to accidents A CAUTION Do not tow a trailer or haul a heavy load for the first 500 miles 800 km Your engine axle or other parts could be damaged For the first 500 miles 800 km that you tow a trailer do not drive over 50 mph 80 km h and do not make starts at full throttle This helps the engine and other parts of your vehicle wear in at the heavier loads Your new vehicle was designed to be used pri marily to carry passengers and cargo Remember t
185. button Place the ignition switch in the ON or ACC position and press the DISC AUX button to switch to the USB input mode If another audio source is playing and a USB memory device is inserted press the DISC AUX button repeatedly until the center display changes to the USB memory mode If the system has been turned off while the USB memory was playing push the ON OFF VOL control knob to restart the USB memory PP gt gt I SEEK CAT and TRACK Reverse or Fast Forward buttons Press and hold the SEEK CAT Ma rewind button or TRACK PPI fast forward button for 1 5 seconds while an audio file on the USB device is playing to reverse or fast forward the track being played The track plays at an in creased speed while reversing or fast forwarding When the button is released the audio file re turns to normal play speed 44 gt p SEEK CAT and TRACK buttons Press the SEEK CAT button M4 while an au dio file on the USB device is playing to return to the beginning of the current track Press the SEEK CAT button M4 several times to skip backward several tracks Press the TRACK button PPI while an audio file on the USB device is playing to advance one track Press the TRACK button P several times to skip forward several tracks If the last track in a folder on the USB device is skipped the first track of the next folder is played Folder selection To change to another folder in the USB memory turn
186. camera It is a preci sion instrument Otherwise it may mal function or cause damage resulting ina fire or an electric shock A CAUTION Do not scratch the camera lens when cleaning dirt or snow from the lens 4 22 Monitor climate audio phone and voice recognition systems HOW TO READ THE DISPLAYED LINES Guiding lines which indicate the vehicle width and distances to objects with reference to the vehicle body line are displayed on the monitor Distance guide lines Indicate distances from the vehicle body Red line f approx 1 5 ft 0 5 m e Yellow line approx 3 ft 1 m Green line 3 approx 7 ft 2 m Green line approx 10 ft 3 m Vehicle width guide lines Indicate the vehicle width when backing up Predicted course lines Indicate the predicted course when backing up The predicted course lines will be displayed on the monitor when the shift selector is in the R Reverse position and the steering wheel is turned The predicted course lines will move de pending on how much the steering wheel is turned and will not be displayed while the steer ing wheel is in the neutral position The vehicle width guide lines and the width of the predicted course lines are wider than the actual width and course HOW TO PARK WITH PREDICTED COURSE LINES AWARNING Always turn and check that it is safe to do so before backing up Always back up slowly Use the displayed lines as a re
187. can be selected in any screen that allows for preferences to be programmed Once the screen is selected you have the option to reset the selected distances or time to a new setting MAINTENANCE gt TIRE gt OIL gt FILTER gt OTHER ENTER NEXT Maintenance mode The maintenance mode allows you to set alerts for the reminding of maintenance intervals for the following engine oil oll filter tires other Set a desired interval by pushing to high light the maintenance field and pressing The reset mode will open up and allow you to enter the desired distance Instruments and controls 2 21 OPTIONS SBACK gt LANGUAGE gt UNIT gt EFFECTS NEXT ENTER Options mode The LANGUAGE UNIT EFFECTS screen will appear when selecting the Language Unit Effects key and pressing Language English French or Spanish Unit US mile F MPG Metric km C L 100 km Effects This changes effects of the indicator needles when ON The needles in the meter sweep and the ring illumination will be brightened gradually when the engine is started 2 22 instruments and controls You can select the language unit or change the dial effects by using the O button and pressing The settings are automatically saved when you exit the menu by pressing the BACK button or any other mode button gt SKIP gt DETAIL NEXT WAENTER Warning mode The warning mode can be selected to view any wa
188. cate the materials in the tire which include steel nylon polyester and others Maximum permissible inflation pres sure This number is the greatest amount of air pressure that should be put in the tire Do not exceed the maximum permissible in flation pressure Maximum load rating This number indicates the maximum load in kilograms and pounds that can be car ried by the tire When replacing the tires on the vehicle always use a tire that has the same load rating as the factory in stalled tire Term of tubeless or tube type Indicates whether the tire requires an in ner tube tube type or not tubeless 7 The word radial The word radial is shown if the tire has radial structure Manufacturer or brand name Manufacturer or brand name is shown Other Tire related Terminology In addition to the many terms that are defined throughout this section Intended Outboard Sidewall is 1 the sidewall that contains a whitewall bears white lettering or bears manufacturer brand and or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or 2 the out ward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle TYPES OF TIRES A WARNING When changing or replacing tires be sure all four tires are of the same type i e Summer All Season
189. cautions when starting and driving 5 2 Push Staring s a be ee ot a Aen wT G 6 10 R Radio Car phone orCBradio 4 91 Compact Disc CD changer 4 54 FM AM radio with compact disc CD changer aoaaa a 4 51 FM AM SAT radio with CD DVD player 4 64 FM AM SAT radio with compact disc CD player oaao 4 57 Steering wheel audio control switch 4 89 Readiness for inspection maintenance UM testa a care woh eiaa e a 9 25 Rear power windows sasaaa aaa 2 45 Rear sals u a ea aeua we de De i a i a 1 6 Rear sun shade aoaaa aa aaa 2 50 RearView Monitor aaa aa aaa aaa 4 22 Rear window and outside mirror defroster SWG 2 ooo me wR Soe a ee ea AA 2 29 Recorders Event data 2 6 es a ea eam ee Re wo 9 26 Refrigerant recommendation 9 6 Registering your vehicle in another country 9 9 Reporting safety defects US only 9 24 S Safety Child safety reardoorlock 3 6 Child seat belts 1 25 1 31 1 36 1 40 Reporting safety defects US only 9 24 Seat adjustment Front power seat adjustment 1 3 Seatback pockets 004 2 40 Seat belt Child safety 2 0 2 0 2 eee 1 23 Infants and small children 1 24 Injured PersOn ssoi saor oa 2 aod ow 4 1 19 Larger children 244 1 24 Precautions on seat belt usage 1 16 Pregnant women aaau aaa 1 19 Seat belt extenders 1 22 Seat belt maintenance 1
190. ce Say Back when prompted to return to the previous screen If you want to cancel the command press and hold the amp switch The message Voice recognition cancelled will be dis played If you want to adjust the volume of the sys tem feedback push the volume control switch on the steering wheel or use the audio system volume knob while the system is making an announcement To minimize the amount of prompts spoken by the system in Alternate Command Mode use the Minimize Voice Feedback function To access the Minimize Voice Feedback function press the SETTING button then select the Others key Then select the Voice Recognition key How to speak numbers Voice Recognition requires a certain way to speak numbers when giving voice commands Refer to the following examples General rule Only single digits O zero to 9 can be used When saying the phone number 800 662 6200 the system will accept eight hundred in addition to eight zero zero or eight oh oh 500 700 and 900 are also supported Examples 1 800 662 6200 One eight zero zero six six two six two zero zero One eight hundred six six two six two zero zero 4 132 Monitor climate audio phone and voice recognition systems Improving Recognition of Phone numbers You can improve the recognition of phone num bers by saying the phone number in three groups of numbers For example
191. ce anything hard or heavy on the seat or pierce it with a pin or similar objects This may result in damage to the climate controlled seat Any liquid spilled on the seat should be removed immediately with a dry cloth The climate controlled seat has an air filter Do not operate the climate con trolled seat without an air filter This may result in damage to the system When cleaning the seat never use gasoline benzine thinner or any simi lar materials If any malfunctions are found or the climate controlled seat does not oper ate turn the switch off and have the system checked by your NISSAN dealer HEATED STEERING WHEEL if so equipped LICO421 The heated steering wheel system is designed to operate only when the surface temperature of the steering wheel is below 68 F 20 C Push the heated steering wheel switch to warm the steering wheel after the engine starts The indicator light will come on If the surface temperature of the steering wheel is below 68 F 20 C the system will heat the steering wheel and cycle off and on to maintain a temperature above 68 F 20 C The indicator light will remain on as long as the system Is on Push the switch again to turn the heated steering wheel system off manually The indicator light will go off NOTE If the surface temperature of the steering wheel is above 68 F 20 C when the switch is turned on the system will not heat the steering wheel T
192. ce recognition systems HOW TO USE THE SETTING Settings 8 00 BUTTON Press the SETTING button This screen displays al sine pe ae and adjusts various settings and functions that are available for your vehicle When the amber indicator next to an item is illuminated the feature is enabled Adjust navigation settings LHA1236 Displa Adjusts the settings for the display screen y y Brightness Contrast Adjusts the brightness or contrast of the map background emoon off Toggles the display screen on and off The amber indicator is illuminated when the display is set to On When the display is set to Off and a control panel audio or heater and air conditioner button is pressed the display will resume until that operation is finished To turn the display back on press and hold the WD OFF button for approximately 2 seconds or return to the display setting screen and adjust the setting Background Color Color Adjusts the display screen between day and night mode Bagon Theme Changes the color of the background arrows and bars on the screen Adjusts the clock settings On screen Clock Toggles on or off the clock in the upper right corner of the display Clock Format Format Toggles between a 12 hour and 24 hour clock Offset Offset hour Offset min Offset min Manually adjusts the hours and minutes of the clock Daylight Savings Time Toggles on or off the daylight savings time Time Zone Adj
193. change the display brightness press the D OFF button Pressing the button again will change the display to the day or the night display The brightness can then be adjusted using the NISSAN controller If no operation is performed within 5 seconds the display will return to the previous display Monitor climate audio phone and voice recognition systems 4 19 IMAGE VIEWER if so equipped USING THE IMAGE VIEWER When a compatible portable storage device is plugged into the USB jack located in the center console compatible image files stored on the device can be viewed on the control panel de vice Connecting the portable storage device To connect a portable storage device to the sys tem so that images stored on it can be viewed insert the device into the USB jack located in the center console Settings gt Image Viewer 1 XXXXXXX jpg 2 XXXXXXX jpg 3 XXXXKXX jpg 4 XXXXXXX jpg Full Screen Display Viewing images To view an image press the SETTING button gt Others and then select the Image Viewer key with the NISSAN controller The Im age Viewer screen will be displayed A list of compatible images on the storage device is displayed on the left side of the screen while the selected image is displayed on the right side of the screen To choose a different picture from the list use the NISSAN controller to scroll through the list once the desired image is high lighted 4 20 M
194. ches again A CAUTION Do not use for extended periods of time with the engine stopped This could result in a discharged battery TRUNK LIGHT The light illuminates when the trunk lid is opened When the trunk lid is closed the light goes off The light will go off after a period of time if the trunk lid is left open unless the ignition switch is in the ON position For bulb replacement procedures refer to Exte rior and interior lights in the Maintenance and do it yourself section of this manual HOMELINK UNIVERSAL TRANSCEIVER if so equipped The HomeLink Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand held transmitters into one built in device HomeLink Universal Transceiver Will operate most Radio Frequency RF devices such as garage doors gates home and office lighting entry door locks and se curity systems Is powered by your vehicle s battery No separate batteries are required If the vehi cle s battery is discharged or is discon nected HomeLink will retain all program ming When the HomeLink Universal Trans ceiver is programmed retain the original transmitter for future programming proce dures Example new vehicle purchases Upon sale of the vehicle the programmed HomeLink Universal Transceiver buttons should be erased for security purposes For additional information refer to Program ming Home
195. child restraint is compatible with your vehicle place your child in the child restraint and check the various adjustments to be sure the child restraint is compatible with your child Choose a child restraint that is designed for your child s height and weight Always follow all recommended procedures Safety Seats seat belts and supplemental restraint system 1 25 All U S states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated Canadian law requires the top tether strap on forward facing child re straints be secured to the designated an chor point on the vehicle WRS0718 LATCH system lower anchor locations LATCH Lower Anchors and Tethers for CHildren SYSTEM Your vehicle is equipped with special anchor points that are used with LATCH Lower Anchors and Tethers for CHildren system compatible child restraints This system may also be referred to as the ISOFIX or ISOFIX compatible system With this system you do not have to use a vehicle seat belt to secure the child restraint The LATCH anchor points are provided to install child restraints in the rear outboard seating posi tions only Do not attempt to install a child restraint in the center position using the LATCH anchors 1 26 Safety Seats seat belts and supplemental restraint system LATCH lower anchor AWARNING Failure to follow
196. children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in jured Keep the car locked with the rear seatback and trunk lid securely latched when not in use and prevent children s access to car keys To fold down the driver side of the rear seat reach Secondary trunk lid release if sO through the opening and pull on the strap O eauinoed located behind the seat quipp For models with a rear center console the trunk can be accessed through the access panel be tween the rear seats as shown The rear seats can be locked using the mechani cal key to prevent unauthorized access Fold down the center arm rest Insert the mechanical key into the trunk com partment access lid lock Fold down the trunk compartment access lid For more in formation on the mechanical key see NISSAN Intelligent Key in the Pre driving checks and adjustments chapter Pull the rear seat trunk release handle 4 1 6 Safety Seats seat belts and supplemental restraint system FRONT SEAT HEAD RESTRAINTS HEADRESTS AWARNING Head restraints headrests supplement the other vehicle safety systems They may provide additional protection against injury in certain rear end colli sions Adjust the head restraints headrests properly as speci fied in this section Check the adjust ment after someone else uses the seat Do not attach anything to the hea
197. ck must be at or above the center of the child s ears If the seatback is lower than the center of the child s ears a high back booster seat 2 should be used lf the booster seat is compatible with your vehicle place the child in the booster seat and check the various adjustments to be sure the booster seat is compatible with the child Always follow all recommended pro cedures All U S states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated The instructions in this section apply to booster seat installation in the rear seats or the front passenger seat Safety Seats seat belts and supplemental restraint system Booster seat installation A CAUTION Do not use the lap shoulder belt in the Automatic Locking Retractor ALR mode when using a booster seat with the seat belts Refer to all Warnings and Cautions in the Child Safety Child Restraint and Booster Seats sections before installing a child restraint Follow these steps to install a booster seat in the rear seat or in the front passenger seat WRS0699 1 If you must install a booster seat in the front seat move the seat to the rear most position Position the booster seat on the seat Only place it in a front facing direction Always follow the booster seat manufacturer s in structions LRS045
198. cle so that the iPod can be controlled with the audio system controls and display screen use the USB jack located in the center console Connect the iPod specific end of the cable to the iPod and the USB end of the cable to the USB jack on the vehicle 1 If your iPod supports charging via a USB connection its battery will be charged while connected to the vehicle with the ignition switch in the ACC or ON position 4 80 Monitor climate audio phone and voice recognition systems While connected to the vehicle the iPod can only be operated by the vehicle audio controls To disconnect the iPod from the vehicle re move the USB end of the cable from the USB jack on the vehicle then remove the cable from the iPod iPod is a trademark of Apple Inc registered in the U S and other countries Compatibility The following models are compatible iPod 5th Generation version 1 2 1 iPod Classic version 1 1 iPod Touch version 2 1 0 iPod Nano 1st generation version 1 3 1 iPod Nano 2nd generation version 1 1 3 iPod Nano 3rd generation version 1 0 2 Make sure that your iPod firmware is updated to the version indicated above XXXXXX XXXXXX Ji XXXXXX Shuffle Off Repeat Off Audio main operation Place the ignition switch in the ACC or ON position Press the AUX button repeatedly to switch to the iPod mode If the system has been turned off while the iPod was playing p
199. cle warranties in your Warranty Information Booklet which comes with your NISSAN vehicle If you did not receive a Warranty Information Booklet or it is lost you may obtain a replace ment by writing to Nissan North America Inc Consumer Affairs Department P O Box 685003 Franklin TN 37068 5003 For Canada Emission Control System Warranty Details of this warranty may be found with other vehicle warranties in your Warranty Information Booklet which comes with your NISSAN vehicle If you did not receive a Warranty Information Booklet or it is lost you may obtain a replace ment by writing to Nissan Canada Inc 5290 Orbitor Drive Mississauga Ontario L4W 4Z5 REPORTING SAFETY DEFECTS For USA If you believe that your vehicle has a de fect which could cause a crash or could cause injury or death you should immedi ately inform the National Highway Traffic Safety Administration NHTSA in addi tion to notifying NISSAN If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot be come involved in individual problems be tween you your dealer or NISSAN To contact NHTSA you may call the Ve hicle Safety Hotline toll free at 1 888 327 4236 TTY 1 800 424 9153 go to http www safercar gov or write to Administrator NHTSA 400 Seventh Street SW Washington D C
200. comes excessive rearrange cargo to allow for proper tongue load Technical and consumer information 9 17 Gross axle weight T11012M Maximum Gross Vehicle Weight GVW maximum Gross Axle Weight GAW The GVW of the towing vehicle must not exceed the Gross Vehicle Weight Rating GVWR shown on the F M V S S C M V S S certification label The GVW equals the combined weight of the unloaded vehicle passengers luggage hitch trailer tongue load and any other optional equipment In addition front or rear GAW must not exceed the Gross Axle Weight Rating GAWR shown on the F M V S S C M V S S certification label 9 18 Technical and consumer information Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating Additional passengers cargo and or optional equipment such as the trailer hitch will add weight to the vehicle and reduce your vehicle s maximum towing capacity and trailer tongue load The vehicle and trailer need to be weighed to confirm the vehicle is within the GVWR Front GAWR Rear GAWR Gross Combined Weight Rating GCWR and Towing capacity All vehicle and trailer weights can be measured using platform type scales commonly found at truck stops highway weigh stations building supply centers or salvage yards To determine the available payload capacity for tongue load use the following procedure 1 Locate the GVWR on the F M V S S C M
201. crease in performance A CAUTION Using a fuel other than that specified could adversely affect the emission control system and may also affect the warranty coverage e Under no circumstances should a leaded gasoline be used because this will damage the three way catalyst Do not use E 15 or E 85 fuel in your vehicle Your vehicle is not designed to run on E 15 E 85 fuel Using E 15 or E 85 fuel in a vehicle not specifically de signed for E 15 or E 85 fuel can ad versely affect the emission control de vices and systems of the vehicle Damage caused by such fuel is not cov ered by the NISSAN new vehicle limited warranty e U S government regulations require ethanol dispensing pumps to be identi fied by a small square orange and black label with the common abbrevia tion or the appropriate percentage for that region Gasoline specifications NISSAN recommends using gasoline that meets the World Wide Fuel Charter WWFC specifi cations where it is available Many of the automo bile manufacturers developed this specification to improve emission control system and vehicle performance Ask your service station manager if the gasoline meets the WWFC specifications Reformulated gasoline Some fuel suppliers are now producing reformu lated gasolines These gasolines are specially designed to reduce vehicle emissions NISSAN supports efforts towards cleaner air and sug gests that you use reformulated gasoline w
202. d restraint headrest stalks or remove the head restraints headrests Do not use Center armrest the seat if the head restraint headrest has been removed If the head restraint headrest was removed rein The illustration shows the seating positions equipped with head restraints headrests The head restraints in the front seats are adjustable stall and properly adjust the head 2d removable restraint headrest before an occupant A Indicates the seating position is equipped with Pull the armrest down until it rests on the seat cushion uses the seating position Failure to fol low these instructions can reduce the effectiveness of the head E Indicates the seating position is equipped with restraints headrests This may increase a headrest the risk of serious injury or death in a collision a head restraint Indicates the seating position is not equipped with a head restraint or headrest Your vehicle is equipped with a head restraint headrest that may be integrated adjustable or non adjustable Safety Seats seat belts and supplemental restraint system 1 7 Adjustable head restraints headrests have multiple notches along the stalk to lock them in a desired adjustment position The non adjustable head restraints headrests have a single locking notch to secure them to the seat frame Proper Adjustment For the adjustable type align the head restraint headrest so the center of your ear IS approxim
203. d by crosswinds rough road surfaces or passing trucks AWARNING Trailer hitch components have specific weight ratings Your vehicle may be ca pable of towing a trailer heavier than the weight rating of the hitch components Never exceed the weight rating of the hitch components Doing so can cause serious personal injury or property damage Hitch ball Choose a hitch ball of the proper size and weight rating for your trailer The required hitch ball size is stamped on most trailer couplers Most hitch balls also have the size printed on the top of the ball Choose the proper class hitch ball based on the trailer weight The diameter of the threaded shank of the hitch ball must be matched to the ball mount hole diameter The hitch ball shank should be no more than 1 16 smaller than the hole in the ball mount The threaded shank of the hitch ball must be long enough to be properly secured to the ball mount There should be at least 2 threads showing beyond the lock washer and nut Technical and consumer information 9 19 Ball mount The hitch ball is attached to the ball mount and the ball mount is inserted into the hitch receiver Choose a proper class ball mount based on the trailer weight Additionally the ball mount should be chosen to keep the trailer tongue level with the ground Sway control device Sudden maneuvers wind gusts and buffeting caused by other vehicles can affect trailer han dl
204. d do it yourself EXTERIOR AND INTERIOR LIGHTS Headlight assembly High Halogen 65 9005 HB3 Low Halogen if so equipped 55 H11 Low Xenon if so equipped 35 D2S Park Turn 3457NAK Side marker 5 WY5W Front fog light if so equipped 55 H11 Front personal map lights 8 Glove box light 3 4 158 Vanity mirror light 1 4 Step light 194 Rear personal lights Door switch illumination High mounted stop light Trunk light Rear combination light Tail Stop Turn signal Backup reversing Sidemarker License plate light Foot well light Door mirror turn signal light if so equipped Always check with the Parts Department at a NISSAN dealer for the latest parts information See a NISSAN dealer for replacement Headlight assembly Map light Rear personal lights Door mirror turn signal light if so equipped Step light Fog light if so equipped High mounted stop light Type A Trunk light High mounted stop light Type B License plate light Rear combination light PON gt Sea ew oO g O Maintenance and do it yourself 8 29 Replacement procedures All other lights are either type A B C or D When replacing a bulb first remove the lens lamp and or cover Indicates bulb removal t Indicates bulb installation 8 30 Maintenance and do it yourself 0 000 Map lights Use a cloth to protect the housing WDI0667 Vanity mirror light Use a cloth to protect the housing WDI0340
205. d in Change intervals Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters Using engine oil and filters that are not of the specified quality or exceeding recommended oil and filter change intervals could reduce engine life Damage to the engine caused by improper maintenance or use of incor rect oil and filter quality and or viscosity is not covered by the NISSAN new vehicle limited war ranty Technical and consumer information 9 5 Your engine was filled with a high quality engine oil when it was built You do not have to change the oil before the first recommended change interval Oil and filter change intervals depend upon how you use your vehicle Operation under the following conditions may require more frequent oil and filter changes repeated short distance driving at cold out side temperatures driving in dusty conditions extensive idling towing a trailer stop and go commuting Refer to the NISSAN Service and Maintenance Guide for the maintenance schedule AIR CONDITIONER SYSTEM REFRIGERANT AND OIL RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger ant HFC 134a R 134a and NISSAN A C system oil Type S or the exact equivalents 9 6 Technical and consumer information A CAUTION The use of any other refrigerant or oil will cause severe damage to the
206. d the battery level Maintenance and do it yourself 8 15 ee WDI0224 1 Remove the vent caps with a screwdriver as shown Use a cloth to protect the battery case 8 16 Maintenance and do it yourself 2 Check the fluid level in each cell If it is necessary to add fluid add only distilled water to bring the level up to the bottom of the filler opening Do not overfill Reinstall the vent caps Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level JUMP STARTING If jump starting is necessary see Jump starting in the In case of emergency section of this manual If the engine does not start by jump starting the battery may have to be replaced Contact a NISSAN dealer VARIABLE VOLTAGE CONTROL SYSTEM A CAUTION e Do not ground accessories directly to the battery terminal Doing so will by pass the variable voltage control sys tem and the vehicle battery may not charge completely e Use electrical accessories with the en gine running to avoid discharging the vehicle battery Your vehicle is equipped with a variable voltage control system This system measures the amount of electrical discharge from the battery and controls voltage generated by the generator The current sensor A is located near the battery along the negative battery cable If you add elec trical accessories to your vehicle be sure to ground them
207. dan emeees nee 8 20 REDIGCING Si ehewearcesen staan EEEE 8 20 Blanes gece eee cee ec pepe ccee eee E ecco we eee 8 21 Pulses EE E E E E 8 22 Engine compartment ccscvecueuesce ovaswae avedes 8 22 Passenger compartment 0 eee eens 8 24 Battery replacement 2220 eee eee eee 8 26 NISSAN Intelligent Key 0 0005 8 26 Cel Coe se ee ee ee eee ee ere 8 27 PICACICNSscheiycewneseseneeeeer ce deaepewente 8 27 Front park turn sidemarker light 8 28 Fog lights if so equipped 00ce eee ee 8 28 Exterior and interior lights 8 28 Wheels and NCSeeetees teeta deens dares dese 8 32 Tike Presse E E eee eee ese ceeds 8 32 Tire labeli cco eects cote kiraan ia 8 36 Types Ot fG e eriiressrcsereeiser ire hennen ra 8 39 WWE Glas E E EE 8 40 Changing wheels and tires ssassn eee eee 8 40 MAINTENANCE REQUIREMENTS Your NISSAN has been designed to have mini mum maintenance requirements with long ser vice intervals to save you both time and money However some day to day and regular mainte nance is essential to maintain your NISSAN s good mechanical condition as well as its emis sions and engine performance It is the owner s responsibility to make sure that the scheduled maintenance as well as general maintenance Is performed As the vehicle owner you are the only one who can ensure that your vehicle receives proper maintenance You are a vital li
208. disc will play If the system has been turned off while the com pact disc was playing pressing the VOL ON OFF control knob will start the compact disc DISC AUX button When the DISC AUX button is pressed with the system off and the compact disc loaded the system will turn on and the compact disc will start to play When the DISC AUX button is pressed with the compact disc loaded but the radio playing the radio will automatically be turned off and the compact disc will start to play Monitor climate audio phone and voice recognition systems 4 67 44 gt gt SEEK CAT and TRACK buttons When the SEEK CAT M4 button is pressed while a compact disc is playing the track being played returns to its beginning Press several times to skip back through tracks The compact disc will go back the number of times the button is pressed When the TRACK PPI button is pressed while the compact disc is playing the next track will start to play from its beginning Press several times to skip through tracks The compact disc will advance the number of times the button is pressed When the last track on the compact disc is skipped through the first track will be played The NISSAN controller can also be used to se lect tracks when a CD is being played 44 gt gt SEEK CAT and TRACK Rewind and Fast Forward buttons Press and hold the SEEK CAT M4 rewind button or the TRACK PPI fast forward button while
209. do not drive the vehicle at speeds faster than 50 MPH 80 km h When driving on roads covered with snow or ice the TEMPORARY USE ONLY spare tire should be used on the rear wheels and the original tire used on the front wheels drive wheels Use tire chains only on the front original tires Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire Replace the spare tire as soon as the tread wear indicators appear Do not use the spare tire on other vehicles Do not use more than one spare tire at the same time Do not tow a trailer when the TEMPO RARY USE ONLY spare tire is installed A CAUTION Do not use tire chains on a TEMPO RARY USE ONLY spare tire Tire chains will not fit properly and may cause dam age to the vehicle Because the TEMPORARY USE ONLY spare tire is smaller than the original tire ground clearance is reduced To avoid damage to the vehicle do not drive over obstacles Also do not drive the vehicle through an automatic car wash since it may get caught Maintenance and do it yourself 8 43 MEMO 8 44 Maintenance and do it yourself 9 Technical and consumer information Capacities and recommended fuel lubricants 9 2 Fuel Recommendation 0cc eee ees 9 3 Engine oil and oil filter recommendations 9 5 Air conditioner system refrigerant and oil recommendations e080 24 senor eceea dans eaddene ons 9 6 SPCIS oe senare E ER
210. dom Repeat All Monitor climate audio phone and voice recognition systems 4 75 This USB device contains multisession contents Please select item to play Play Movie Contents Play Audio Contents USB INTERFACE models with Navigation System Connecting a device to the USB input jack AWARNING Do not connect disconnect or operate the USB device while driving Doing so can be a distraction If distracted you could lose control of your vehicle and cause an acci dent or serious injury 4 76 Monitor climate audio phone and voice recognition systems A CAUTION e Do not force the USB device into the USB port Inserting the USB device tilted or up side down into the port may damage the port Make sure that the USB device is connected correctly into the USB port Do not grab the USB port cover if so equipped when pulling the USB device out of the port This could damage the port and the cover Do not leave the USB cable in a place where it can be pulled unintentionally Pulling the cable may damage the port Refer to your device manufacturer s owner infor mation regarding the proper use and care of the device The USB input jack is located in the center con sole Insert the USB device into the jack 4 When a compatible storage device is plugged into the jack compatible audio files on the stor age device can be played through the vehicle s audio system Audio file operation DISC AUX
211. driver s seat steering col umn and outside mirrors can be stored in the automatic drive positioner memory Follow these procedures to use the memory system 1 Set the Continuously Variable Transmission CVT shift lever to the P Park position 2 Place the ignition in the ON position 3 Adjust the driver s seat steering column and outside mirrors to the desired positions by manually operating each adjusting switch For additional information see Seats in the Safety Seats seat belts and supplemental restraint system section and Outside mirrors in this section During this step do not place the ignition switch in any position other than ON 4 Push the SET switch and within 5 seconds push the memory switch 1 or 2 The indicator light for the pushed memory switch will come on and stay on for approxi mately 5 seconds after pushing the switch After the indicator light goes off the se lected positions are stored in the selected memory 1 or 2 If a new memory is stored in the same memory switch the previous memory will be deleted Linking a keyfob to a stored memory position Each keyfob can be linked to a stored memory position memory switch 1 or 2 with the follow ing procedure 1 Follow the steps for storing a memory posi tion 2 While the indicator light for the memory switch being set is illuminated for 5 sec onds press the 1 button on the keyfob The indicator light
212. during setup the setup will be canceled and or the display will return to the previous screen Finish setup In some screens pressing the BACK button accepts the changes made during setup Monitor climate audio phone and voice recognition systems 4 5 Settings gt Time Zone Pacific Mountain Central Eastern Atlantic z ON i Manually set the time zone 5 4 3 HOW TO SELECT MENUS ON THE SCREEN Vehicle functions are viewed on the center dis play screen in menus Whenever a menu selec tion is made or menu item is highlighted different areas on the screen provide you with important information See the following for details 1 Header Shows the path used to get to the current screen for example press the SETTING button gt then select the Clock key then select the Time Zone key 2 Menu Selections Shows the options to choose within that menu screen for example Pacific time zone Mountain time zone etc 3 UP DOWN Movement Indicator Shows that the NISSAN controller may be used to move UP DOWN on the screen and select more options 4 Screen Count Shows the number of menu selections avail able for that screen for example 1 9 5 Footer Information Line Provides more information if available about the menu selection currently high lighted for example Manually set the time zone HOW TO USE THE STATUS BUTTON To display the status of the audio climate
213. dvanced operation you can change to an Alternate Command Mode that enables the op eration of the display and audio system through NISSAN Voice Recognition When this mode is active an expanded list of commands can be spoken after pushing the TALK amp switch on the steering wheel and the voice command menu prompts are turned off In Alternate Command Mode the recognition success rate may be affected because the num ber of available commands and the ways of speaking each command are increased See NISSAN Voice Recognition Alternate Com mand Mode in this section To improve the recognition success rate when Alternate Command Mode is active try using the Speaker Adaptation Function available in that mode See Speaker Adaptation Function in this section Otherwise it is recommended that Alter nate Command Mode be turned off and Standard Mode be used for the best recognition perfor mance While using the NISSAN Voice Recognition sys tem for certain Phone and Navigation features you can switch to using manual controls touch screen NISSAN controller steering wheel con trols and the information you have already en tered by voice control will be retained To switch to manual controls select the Manual Controls key on the display when it appears The system will respond by speaking Changing to manual operation Please use manual controls to con tinue For the voice commands for the navigation sys
214. e Once your cellular phone is connected to the in vehicle phone module no other phone con necting procedure is required Your phone is automatically connected with the in vehicle phone module when the ignition switch is placed in the ON position with the connected cellular phone turned on and carried in the vehicle You can register up to 5 different Bluetooth cellular phones to the in vehicle phone module However you can talk on only one cellular phone at a time NISSAN Voice Recognition system supports the phone commands so dialing a phone number using your voice is possible For more details see NISSAN Voice Recognition System in this sec tion Before using the Bluetooth Hands Free Phone System refer to the following notes Set up the wireless connection between a cellular phone and the in vehicle phone module before using the hands free phone system Some Bluetooth enabled cellular phones may not be recognized by the in vehicle phone module Please visit www nissanusa com bluetooth for a recom mended phone list and connecting You will not be able to use a hands free phone under the following conditions Your vehicle is outside of the cellular ser vice area Your vehicle is in an area where it is difficult to receive cellular signal such as in a tunnel in an underground parking garage near a tall building or in a moun tainous area Your cellular phone is locked to preve
215. e left channel audio input Yellow video input Before connecting a device to the auxiliary input jacks turn off the power of the portable device With a compatible device connected to the aux illary input jacks press the AUX button until the AUX mode appears in the display The output from the device will be played through the display when the vehicle is in the P Park position and the parking brake engaged and audio system Monitor climate audio phone and voice recognition systems 4 61 AUX gt Menu Display Mode o AUX settings Select the Settings key using the NISSAN con troller and press the ENTER button Choose one of the display modes by selecting the 4 keyorthe gt key Normal e Wide Cinema Additional features For more information about the iPod player available with this system see iPod player operation without Navigation System in this sec tion For more information about the USB interface available with this system see USB interface models without Navigation System in this sec tion 4 62 Monitor climate audio phone and voice recognition systems No satellite radio reception is available when the SAT button is pressed to access satellite radio stations unless optional sat ellite receiver and antenna are installed and a SiriusXM Satellite Radio service subscription is active Satellite radio is not E 2 3 4 5 6 available in Al
216. e duces certain parts of sound that seem in audible to most people WMA Windows Media Audio WMA is a compressed audio format created by Micro soft as an alternative to MP3 The WMA codec offers greater file compression than the MP3 codec enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality AAC M4A Advanced Audio Coding AAC is a lossy audio compression format Audio files that have been encoded with AAC are generally smaller in size and deliver a higher quality of sound than MP3 ATRAC3 ATRAC3 Plus Adaptive Trans form Acoustic Coding ATRAC is a lossy audio compression format developed by Sony Bit rate Bit rate denotes the number of bits per second used by a digital music file The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file Sampling frequency Sampling frequency is the rate at which the samples of a signal are converted from analog to digital A D conversion per second Multisession Multisession is one of the methods for writing data to media Writing data once to the media is called a single session and writing more than once is called a multisession e ID3 WMA Tag The ID3 WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title artist album title encoding bit rate track ti
217. e Repeat and Audio books For further information about each item see the iPod Owner s Manual SEEK CAT and TRACK buttons When the 44 SEEK CAT button or gt gt TRACK button is pressed for less than 1 5 sec onds while the iPod is playing the next track or the beginning of the current track on the iPod will be played When the 44 SEEK CAT button or PP TRACK button is pressed for more than 1 5 sec onds while the iPod is playing the iPod will play while fast forwarding or rewinding When the button is released the iPod will return to the normal play speed The NISSAN controller can also be used to se lect tracks when the iPod is playing 8 00 iPod gt Artists Scrolling menus While navigating long lists of artists albums or songs in the music menu it is possible to scroll the list by the first letter To activate letter index ing perform one of the following Turn the NISSAN controller quickly Press and hold the up down directional ar rows on the NISSAN controller Touch and hold the page up down arrows on the touchscreen To exit the scrolling by letter mode perform one of the following Press the ENTER button on the NISSAN controller Push the ENTER switch on the steering wheel Do not touch the controls for 2 seconds BLUETOOTH STREAMING AUDIO if so equipped If you have a compatible Bluetooth audio de vice that is capable of playing audio files
218. e clock Monitor climate audio phone and voice recognition systems 4 9 Comfort amp Convenience Select the Others key using the NISSAN controller then select the Comfort key The Comfort settings screen will be displayed You can set the following operating conditions by selecting the desired item using the NISSAN controller The indicator light box at the right of the selected item alternately turns on and off each time the item is touched or the ENTER button is pressed Indicator light is tlluminated ON Indicator light is not illuminated OFF Select to change the duration of the automatic headlight off timer After selecting the item turn the NISSAN controller or touch the or key to change the setting The available delays are O 30 45 60 90 120 150 and 180 second periods Selective Door Unlock When this item is turned on only the driver s door is unlocked first after the door unlock operation When the door handle request switch on the driver s or front passenger s side door is pushed to be unlocked only the corresponding door is unlocked first All the doors can be unlocked if the door unlock operation is performed again within one minute Intelligent Key Lock Unlock Select to turn on or turn off the door lock unlock function by pushing the door handle request switch Lift Steering Wheel on Exit Select to turn on or turn off the steering wheel moving upward for easy exit when the ignition swi
219. e in the seat belts check the operation as follows Grasp the shoulder belt and pull forward quickly The retractor should lock and re strict further belt movement If the retractor does not lock during this check or if you have any questions about seat belt opera tion see a NISSAN dealer Shoulder belt height adjustment front seats The shoulder belt anchor height should be ad justed to the position best for you See Precau tions on seat belt usage earlier in this section To adjust pull out the adjustment button and move the shoulder belt anchor to the desired position so the belt passes over the center of the shoulder The belt should be away from your face and neck but not falling off your shoulder Release the adjustment button to lock the shoul der belt anchor into position AWARNING e After adjustment release the adjust ment button and try to move the shoul der belt anchor up and down to make sure it is securely fixed in position The shoulder belt anchor height should be adjusted to the position best for you Failure to do so may reduce the effec tiveness of the entire restraint system and increase the chance or severity of injury in an accident SEAT BELT EXTENDERS If because of body size or driving position it is not possible to properly fit the lap shoulder belt and fasten it an extender that is compatible with the installed seat belts is available that can be purchased The
220. e no cracks deformation rot or loose connections Underbody The underbody is frequently ex posed to corrosive substances such as those used on icy roads or to control dust It is very important to remove these substances from the underbody otherwise rust may form on the floor pan frame fuel lines and exhaust system At the end of winter the underbody should be thor oughly flushed with plain water in those areas where mud and dirt may have accumulated See the Appearance and care section of this manual Windshield washer fluid Check that there is adequate fluid in the reservoir MAINTENANCE PRECAUTIONS When performing any inspection or maintenance work on your vehicle always take care to prevent serious accidental injury to yourself or damage to the vehicle The following are general precau tions which should be closely observed AWARNING Park the vehicle on a level surface ap ply the parking brake securely and block the wheels to prevent the vehicle from moving Move the shift lever to P Park Be sure the ignition switch is in the OFF or LOCK position when performing any parts replacement or repairs If you must work with the engine run ning keep your hands clothing hair and tools away from moving fans belts and any other moving parts It is advisable to secure or remove any loose clothing and remove any jewelry such as rings watches etc before working on your vehicle e Always
221. e number of bits per second used by a digital video files The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file Monitor climate audio phone and voice recognition systems 4 49 Requirements for Supporting Video Playback CD CD R CD RW DVD DVD R DVD RW DVD RW DL USB 2 0 Memory CD CD R CD RW DVD ISO9660 LEVEL1 ISO9660 LEVEL2 Romeo Joliet UDF Bridge UDF1 02 ISO9660 UDF1 5 UDF2 0 DVD R DVD RW DVD RW ISO9660 Level 3 packet writing is not supported File Systems DL Files saved using the Live File System component on a Windows Vista based computer are not supported VDF1 5 VDF2 0 packet writing is not supported USB Memory FAT16 FAT32 divx avi Video Codecs DivX8 DivX4 DivX5 DivX6 File T Audio Codecs MP3 MPEG2 5 Audio Layer3 AC3 LPCM ile es d ast Video Codec ISO MPEG4 Audio Codec G 726 ax av Mbps Bit Rates 8 Mbps Gi av 32x82 720 x 480 Resolution a 32x82 720x576 4 50 Monitor climate audio phone and voice recognition systems eS T O O W w ty We os L AM FM DISC RPT RDM amp CD eject button VOL ON OFF control knob Station and CD select 1 6 buttons LOAD CD button m AUX SEEK lt 4 cat TRACK mi TUNE FOLDER and AUDIO control knob Bass Treble Fade Balance SSV if so equipped and Beep AUX IN jack AUX button TRACK button 9 SEEK CAT button 10 DISC button
222. e or district and registered its modifications transporta tion and registration are the responsibility of the user NISSAN is not responsible for any inconvenience that may result VEHICLE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER VIN PLATE The vehicle identification number VIN plate is attached as shown This number is the identifica tion for your vehicle and is used in the vehicle registration VEHICLE IDENTIFICATION NUMBER chassis number The vehicle identification number is located as shown Technical and consumer information 9 9 WT10172 ENGINE SERIAL NUMBER F M V S S C M V S S CERTIFICATION LABEL The Federal Canadian Motor Vehicle Safety Standard F M V S S C M V S S certification la bel is affixed as shown This label contains valu able vehicle information such as Gross Vehicle Weight Ratings GVWR Gross Axle Weight Rating GAWR month and year of manufacture Vehicle Identification Number VIN etc Review it carefully The number is stamped on the engine as shown 9 10 Technical and consumer information EMISSION CONTROL INFORMATION LABEL The emission control information label is at tached to the underside of the hood as shown INSTALLING FRONT LICENSE PLATE TIRE AND LOADING INFORMATION AIR CONDITIONER SPECIFICATION LABEL LABEL To mount the front license plate attach the li m aa oe cense plate bracket to the plastic finisher at the The c
223. e phone dial eight three zero five one record name four three pause two nine pause zero delete redial number phonebook list names call eight oh five four one correction connect phone dial seven four oh one eight previous entry delete dial nine seven two six six call seven six three oh one go back call five six two eight zero dial six six four three seven MANUAL CONTROL While using the voice recognition system it is possible to select menu options by using the steering wheel controls instead of speaking voice commands The manual control mode does not allow dialing a phone number by digits The user may select an entry from the Phonebook or Re cent Calls lists To re activate voice recognition exit the manual control mode by pressing and holding the PHONE END _ button At that time pressing the PHONE SEND 4 button will start the Hands Free Phone System Monitor climate audio phone and voice recognition systems 4 103 Operating tips To enter manual control mode start the voice recognition system and tilt the tuning switch up or down The system will speak Showing Manual Options when manual controls are initially activated To browse the menu options tilt the tuning switch up or down The system will always speak the current menu option De pending on the audio display it will also show the current menu option To select the current menu opti
224. e place 8 Note that any object on the hill is further than it appears on the monitor Backing up on a steep downhill When backing up the vehicle down a hill the distance guide lines and the vehicle width guide lines are shown farther than the actual distance For example the display shows 8 ft 1 0 m to the place A but the actual 3 ft 1 0 m distance on Monitor climate audio phone and voice recognition systems 4 25 the hill is the place 8 Note that any object on the hill is closer than it appears on the monitor Backing up near a projecting object The predicted course lines do not touch the object in the display However the vehicle may hit the object if it projects over the actual backing up course 4 26 Monitor climate audio phone and voice recognition systems Backing up behind a projecting object The position is shown farther than the position in the display However the position is actually at the same distance as the position The vehicle may hit the object when backing up to the position if the object projects over the actual backing up course HOW TO ADJUST THE SCREEN To adjust the Display ON OFF Brightness Tint Color Contrast and Black Level of the RearView Monitor press the SETTING button with the RearView Monitor on and select the Display key Select one of the items and change the value by touching the or key or by turning the NISSAN contro
225. e recognition systems 4 95 a PHONE END While the voice recognition system Is active press and hold the but ton for 5 seconds to quit the voice recognition system at any time TUNING SWITCH While using the voice recognition system tilt the tuning switch up or down to manually control the phone system if so equipped GETTING STARTED The following procedures will help you get CONTROL BUTTONS started using the Bluetooth Hands Free Phone The control buttons for the Bluetooth Hands Free System with NISSAN Voice Recognition For ad Phone System are located on the steering wheel ditional command options refer to List of voice 4 PHONE SEND commands in this section Press the 4 button to initiatea VR Choosing a language session or answer an incoming call You can interact with the Bluetooth Hands Free Phone System using English Spanish or You can also use the 4 button to French interrupt the system feedback and give acommand at once See List of voice commands and During a call 1 Press and hold the f button for more in this section for more information than 5 seconds To change the language perform the following 4 96 Monitor climate audio phone and voice recognition systems The system announces Press the PHONE SEND f amp button for the hands free phone system to enter the voice adaptation mode or press the PHONE END button to select a different lan guage
226. e shift lever to the P Park position Firmly depress the parking brake pedal and it will release Before driving be sure the brake warning light goes out CRUISE CONTROL ACCEL RES CD COAST SET CANCEL switch ACCEL RES switch COAST SET switch ON OFF switch PRECAUTIONS ON CRUISE CONTROL If the cruise control system malfunctions it cancels automatically AWARNING Do not use the cruise control when driving under the following conditions When it is not possible to keep the vehicle at a set speed In heavy traffic or in traffic that varies in speed On winding or hilly roads On slippery roads rain snow ice etc In very windy areas Doing so could cause a loss of vehicle control and result in an accident CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed be tween 25 89 MPH 40 144 km h without keeping your foot on the accelerator pedal To turn on the cruise control push the ON OFF switch on The CRUISE indicator light in the instrument panel will illuminate Starting and driving 5 19 To set cruising speed accelerate the vehicle to the desired speed push the COAST SET switch and release it Take your foot off the accelerator pedal Your vehicle maintains the set speed e To pass another vehicle depress the ac celerator pedal When you release the pedal the vehicle returns to the previously set speed The vehicle may not maintain the
227. e stem cap 7 Check the pressure of all other tires Checking tire pressure including the spare 1 Remove the valve stem cap from the tire 2 Press the pressure gauge squarely onto the valve stem Do not press too hard or force the valve stem side ways or air will escape If the hissing sound of air escaping from the tire is heard while checking the pressure reposition the gauge to eliminate this leakage 3 Remove the gauge Maintenance and do it yourself 8 35 Size Cold Tire Inflation Pres sure P245 45VR18 230 kPa 33 PSI Front Original Tire P245 40VR19 230 kPa 33 PSI 245 40WR19 230 kPa 33 PSI Rear Original Tire 8 36 Maintenance and do it yourself WDI0394 Example TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires This information iden tifies and describes the fundamental characteristics of the tire and also pro vides the tire identification number TIN for safety standard certification The TIN can be used to identify the tire in case of a recall 7 H Tire speed rating You should not drive the vehicle faster than the tire P215 65R15 95H speed rating 6 R 15 t t t 4 5 3 WDI0395 Example 1 Tire size example P215 65R15 95H 4 R The R stands for radial 1 P The P indicates the tire is de 5 Two digit number 15 This number signed for passenger vehicles not all is the wheel or rim diame
228. e system is armed It is not however a motion detection type system that activates when a vehicle is moved or when a vibration occurs The system helps deter vehicle theft but cannot prevent it nor can it prevent the theft of interior or exterior vehicle components in all situations Al 2 26 Instruments and controls ways secure your vehicle even if parking for a brief period Never leave your Intelligent Key in the vehicle and always lock the vehicle when unattended Be aware of your surroundings and park in secure well lit areas whenever possible Many devices offering additional protection such as component locks identification markers and tracking systems are available at auto supply stores and specialty shops Your NISSAN dealer may also offer such equipment Check with your insurance company to see if you may be eligible for discounts for various theft protection features How to arm the vehicle security system 1 Close all windows The system can be armed even if the windows are open 2 Remove the Intelligent Key from the vehicle 3 Close all doors hood and trunk Lock all doors The doors can be locked with the Intelligent Key door handle request switch or power door lock switch 4 Confirm that the security indicator light comes on The security light stays on for about 30 seconds The vehicle security sys tem is now pre armed After about 30 sec onds the vehicle security system automati cally shi
229. e wheels on the vehicle could lead to mechanical damage e For additional information regarding tires refer to Important Tire Safety Information US or Tire Safety Infor mation Canada in the Warranty In formation Booklet Care of wheels Wash the wheels when washing the vehicle to maintain their appearance Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed Do not use abrasive cleaners when washing the wheels Inspect wheel rims regularly for dents or corrosion Such damage may cause loss of pressure or poor seal at the tire bead NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter Spare tire TEMPORARY USE ONLY spare tire Observe the following precautions if the TEM PORARY USE ONLY spare tire must be used Otherwise your vehicle could be damaged or involved in an accident AWARNING The spare tire should be used for emer gency use only It should be replaced with the standard tire at the first oppor tunity to avoid possible tire or differen tial damage Drive carefully while the TEMPORARY USE ONLY spare tire is installed Avoid sharp turns and abrupt braking while driving Periodically check spare tire inflation pressure Always keep the pressure of the TEMPORARY USE ONLY spare tire at 60 psi 420 kPa 4 2 bar With the TEMPORARY USE ONLY spare tire installed
230. earmost position Child restraints for infants must be used in the rear facing direction and therefore must not be used in the front seat Safety Seats seat belts and supplemental restraint system 1 35 2 Position the child restraint on the seat Al ways follow the child restraint manufactur er s instructions The back of the child restraint should be secured against the vehicle seatback If necessary adjust or remove the head restraint headrest to obtain the correct child restraint fit If the head restraint headrest is removed store it in a secure place Be sure to reinstall the head restraint headrest when the child restraint is removed See Head restraints headrests in this sec tion for head restraint headrest adjustment removal and installation information If the seating position does not have an adjustable head restraint headrest and it is interfering with the proper child restraint fit try another seating position or a different child restraint WRS0680 Forward facing step 3 3 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manufacturer s in structions for belt routing If the child restraint is equipped with a top tether strap route the top tether strap and secure the tether strap to the tether anchor point rear seat installation only See In stalling top t
231. ed correctly into the USB port Do not grab the USB port cover if so equipped when pulling the USB device out of the port This could damage the port and the cover Do not leave the USB cable in a place where it can be pulled unintentionally Pulling the cable may damage the port The vehicle is not equipped with a USB device USB devices should be purchased separately as necessary This system cannot be used to format USB de vices To format a USB device use a personal computer In some states area the USB device for the front seats plays only sound without images for regu latory reasons even when the vehicle is parked This system supports various USB memory de vices USB hard drives and iPod players Some USB devices may not be supported by this sys tem Partitioned USB devices may not play cor rectly Some characters used in other languages Chinese Japanese etc may not appear properly in the display Using English lan guage characters with a USB device is rec ommended General notes for USB use Refer to your device manufacturer s owner information regarding the proper use and care of the device Notes for iPod use iPod is a trademark of Apple Inc registered in the U S and other countries Improperly plugging in the iPod may cause a checkmark to be displayed on and off flickering Always make sure that the iPod is connected properly An iPod nano 1st Gen
232. ed the available cargo and luggage load capacity calculated in Step 4 6 If your vehicle will be towing a trailer load from your trailer will be trans ferred to your vehicle Consult this manual to determine how this re duces the available cargo and lug gage load capacity of your vehicle Before driving a loaded vehicle confirm that you do not exceed the Gross Vehicle Weight Rating GVWR or the Gross Axle Weight Rating GAWR for your vehicle See Measurement of weights later in this section Also check tires for proper inflation pres sures See the Tire and Loading Informa tion label LOADING TIPS The GVW must not exceed GVWR or GAWR as specified on the F M V S S C M V S S certification label Do not load the front and rear axle to the GAWR Doing so will exceed the GVWR AWARNING e Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting Do not place cargo higher than the seat backs In a sudden stop or colli sion unsecured cargo could cause personal injury e Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs If you do parts of your vehicle can break tire damage could occur or it can change the way your vehicle handles This could result in loss of control and cause per sonal injury Overloading not only can shorten the life of your vehicle and the tire but can also cause unsafe vehicle handling and longer
233. ee eai 2 43 H Hands free phone system Bluetooth aoaaa a aaa 4 92 4 106 Hazard warning flasher switch 6 2 Headlight and turn signal switch 2 30 Headlight control switch 2 31 Headlights a aoaaa a de oe 8 27 Head restraints Active Head Restraint 1 8 1 15 Heated seats 0005 2 35 2 37 Heated steering wheel 2 37 Heater Heater and air conditioner controls 2 cm 64 d Je aa 4 30 4 34 Heater operation 4 31 4 35 HomeLink Universal Transceiver 2 54 Hood release 0 0 0 0 ee ee es 3 18 Horn a x ca a 2 35 l Ignition Switch Push Button Ignition Switch 5 7 Image viewer 1 2 ee ee ee 4 19 Immobilizer system 2 27 3 3 5 10 Important vehicle information label 9 10 In cabin microfilter 004 8 19 Increasing fuel economy 5 22 Indicator lights and audible reminders See warning indicator lights and audible reminders 0 000 eee ee et ees 9 10 Inside automatic anti glare mirror 3 26 Instrument brightness control 2 34 Instrument panel 0 6 2 3 Instrument panel dimmer switch 2 34 Intelligent Key system Key operating range 3 8 Key operation 2 0004 3 10 Mechanical key 2 2 eee ees 3 3 Remote keyless entry operation 3 13 Troubleshooting guide 3 16 Warning signals 0 4 a ae
234. een Select the Back key to return to the previous menu screen Select the Hide key to hide the opera tion keys Title Menu DVD VIDEO Some menus specific to each disc will be shown For details see the instructions at tached to the disc Title Search DVD VIDEO DVD VR The scene with the specified title will be displayed the number of times the or side is selected Group Search VIDEO CD The scene with the specified group will be displayed the number of times the or side is selected 10 Key Search DVD VIDEO VIDEO CD CD DA DVD VR Select the 10 Key Search key to open the number entry screen Input the number you want to search for and select the OK key The specified Title Chapter or Group Track will be played Select No VIDEO CD Select the Select No key to open the number entry screen Input the number you want to search for and select the OK key The specified scene will be played Angle DVD VIDEO If the DVD contains different angles such as moving images the current image angle can be switched to another one Select the Angle key and use the or key to change the angle Angle Mark DVD VIDEO When this item is turned on an angle mark will be shown on the bottom of the screen if the scene can be seen from a different angle Menu Skip DVD VIDEO DVD menus are automatically configured
235. ehicle are not part of this system The purpose of the regulation is to help reduce the risk of injury or death from an inflating air bag to certain front passenger seat occupants such as children by requiring the air bag to be auto matically turned OFF Certain sensors are used to meet the requirements One sensor used is the occupant classification sensor pattern sensor It is in the bottom of the front passenger seat cushion and is designed to detect an occupant and objects on the seat by weight It works together with seat belt sensors described later For example if a child is in the front passenger seat the Advanced Air Bag System is designed to turn the passenger air bag OFF in accordance with the regulations Also if a child restraint of the type specified in the regulations is on the seat its weight and the child s weight can be detected and cause the air bag to turn OFF Occu pant classification sensor operation can vary de pending on the front passenger seat belt sensors The front passenger seat belt sensors are de signed to detect if the seat belt is buckled Based on the weight on the seat detected by the occu pant classification sensor the Advanced Air Bag System determines whether the front passenger air bag should be automatically turned OFF as required by the regulations Safety Seats seat belts and supplemental restraint system 1 51 Front passenger seat adult occupants who are properly seated and usi
236. ehicle being jump started A CAUTION Do not keep the starter motor engaged for more than 10 seconds If the engine does not start right away place the ignition switch in the OFF position and wait 3 to 4 seconds before trying again 7 After starting the engine carefully discon nect the negative cable and then the positive cable 8 Replace the vent caps if so equipped Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid In case of emergency 6 9 PUSH STARTING A CAUTION CVT models cannot be push started or tow started Attempting to do so may cause transmission damage e Do not push start this vehicle The three way catalyst may be damaged 6 10 In case of emergency IF YOUR VEHICLE OVERHEATS If your vehicle is overheating indicated by an extremely high temperature gauge reading or if you feel a lack of engine power detect abnormal noise etc take the following steps AWARNING Do not continue to drive if your vehicle overheats Doing so could cause engine damage or a vehicle fire e To avoid the danger of being scalded never remove the radiator cap while the engine is still hot When the radiator cap is removed pressurized hot water will spurt out possibly causing serious injury Do not open the hood if steam is com ing out 1 Move the vehicle safely off the road apply the parking brake and move the shift lever to P Park
237. ehicle clean Always check for minor damage to the paint and repair it as soon as possible Keep drain holes at the bottom of the doors open to avoid water accumulation Check the underbody for accumulation of sand dirt or salt If present wash with water as soon as possible A CAUTION e NEVER remove dirt sand or other de bris from the passenger compartment by washing it out with a hose Remove dirt with a vacuum cleaner or broom Never allow water or other liquids to come in contact with electronic compo nents inside the vehicle as this may damage them Chemicals used for road surface de icing are extremely corrosive They accelerate corrosion and deterioration of underbody components such as the exhaust system fuel and brake lines brake cables floor pan and fenders In winter the underbody must be cleaned periodically For additional protection against rust and corro sion which may be required in some areas con sult a NISSAN dealer License plate bracket padding 1 A OW N License plate Trunk License plate frame Padding A CAUTION A license plate frame could vibrate and cause noise or paint damage To avoid damage or noise add a soft adhesive pad with a maximum thickness of 1 8 in 4 mm to the back lower edge of the license plate frame Appearance and care 7 7 MEMO 7 8 Appearance and care 8 Maintenance and do it yourself Maintenance requirements 0
238. el 2 Select the Others key using the NISSAN controller 3 Select the Voice Recognition key using the NISSAN controller NOTE You can skip steps 1 to 3 if you say Help Select the Command List key using the NISSAN controller Select a category using the NISSAN con troller The command list for the category selected is shown If necessary scroll the screen using the NISSAN controller to view the entire list Press the BACK button to return to the previous screen Monitor climate audio phone and voice recognition systems 4 127 Alternate Command Mode command list Phone Commands Makes a call to a spoken phone number up to 10 digits Incoming Calls Shows the last 5 incoming phone calls Outgoing Calls Shows the last 5 outgoing phone calls Missed Calls Shows the last 5 missed phone calls Makes a call to a contact that is stored in either the Vehicle Phonebook or Handset Phonebook Please say Call followed by a stored name Navigation Commands 4 128 Monitor climate audio phone and voice recognition systems COMMAND ACTION Birdview Map Changes the Map display to Birdview Planview Map Changes the Map display to a 2 dimensional view North Up Changes the Map display to keep north pointing up on the screen Information Commands Audio Commands AM Turns tothe AMI band selecting the stafon last played FFM Turns othe FM band selecting the station
239. ell back and upright in the seat The front air bags inflate with great force Even with the NISSAN Advanced Air Bag Sys tem if you are unrestrained leaning forward sitting sideways or out of posi tion in any way you are at greater risk of injury or death in a crash You may also receive serious or fatal injuries from the front air bag if you are up against it when it inflates Always sit back against the seatback and as far away as practi cal from the steering wheel or instru ment panel Always use the seat belts The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened The Advanced Air Bag System monitors the severity of a collision and seat belt us age then inflates the air bags as needed Failure to properly wear seat belts can increase the risk or severity of injury in an accident The front passenger seat is equipped with an occupant classification sensor pattern sensor that turns the front passenger air bag OFF under some con ditions This sensor is only used in this seat Failure to be properly seated and wearing the seat belt can increase the risk or severity of injury in an accident See Front passenger air bag and sta tus light later in this section Keep hands on the outside of the steer ing wheel Placing them inside the steering wheel rim could increase the risk that they are injured when the front air bag inflates Safety Seats
240. emory mode If the system has been turned off while the USB memory was playing push the ON OFF VOL control knob to restart the USB memory PP gt gt I SEEK CAT and TRACK Reverse or Fast Forward buttons Press and hold the SEEK CAT M4 rewind button or TRACK PPI fast forward button for 1 5 seconds while an audio file on the USB device is playing to reverse or fast forward the track being played The track plays at an in creased speed while reversing or fast forwarding When the button is released the audio file re turns to normal play speed 44 gt SEEK CAT and TRACK buttons Press the SEEK CAT button M4 while an au dio file on the USB device is playing to return to the beginning of the current track Press the SEEK CAT button M4 several times to skip backward several tracks Press the TRACK button P while an audio file on the USB device is playing to advance one track Press the TRACK button PPI several times to skip forward several tracks If the last track in a folder on the USB device is skipped the first track of the next folder is played Folder selection To change to another folder in the USB memory turn the TUNE FOLDER knob or choose a folder displayed on the screen RPT RDM button When the RPT RDM button is pressed while the USB memory is playing the play pattern can be changed as follows Repeat All 1 Folder Repeat 1 Track Repeat All Random 1 Folder Ran
241. en Doors do not lock with the door handle request switch with the Intelligent Key inside the vehicle and a beep sounds to warn you However when an Intelligent Key is inside the vehicle doors can be locked with an other Intelligent Key A CAUTION After locking the doors using the re quest switch make sure that the doors have been securely locked by operating the door handles or the trunk opener switch When locking the doors using the re quest switch make sure to have the Intelligent Key in your possession be fore operating the request switch to prevent the Intelligent Key from being left in the vehicle The request switch is operational only when the Intelligent Key has been de tected by the Intelligent Key system Lockout protection To prevent the Intelligent Key from being acci dentally locked in the vehicle lockout protection is equipped with the Intelligent Key When the driver s side door is open the doors are locked and then the Intelligent Key is put inside the vehicle and all the doors are closed the lock will automatically unlock and the door buzzer sounds NOTE The doors may not lock when the Intelli gent Key is in the same hand that is oper ating the request switch to lock the door Put the Intelligent Key in a purse pocket or your other hand A CAUTION The lockout protection may not function under the following conditions When the Intelligent Key is placed on top
242. enger seat Keep seatbacks as upright as pos sible after fitting the child restraint Infants and children should always be placed in an appropriate child re straint while in the vehicle When the child restraint is not in use keep it secured with the LATCH system or a seat belt In a sudden stop or colli sion loose objects can injure occupants or damage the vehicle A CAUTION A child restraint in a closed vehicle can become very hot Check the seating sur face and buckles before placing a child in the child restraint This vehicle is equipped with a universal child restraint anchor system referred to as the LATCH Lower Anchors and Tethers for CHildren sys tem Some child restraints include rigid or webbing mounted attachments that can be con nected to these anchors For details see LATCH Lower Anchors and Tethers for CHildren sys tem later in this section If you do not have a LATCH compatible child restraint the vehicle seat belts can be used Several manufacturers offer child restraints for infants and children of various sizes When se lecting any child restraint keep the following points in mind Choose only a restraint with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213 Check the child restraint in your vehicle to be sure it is compatible with the vehicle s seat and seat belt system If the
243. ensacestnecneeh ex 0 9 Passenger compartment 00 cece eee nnn 0 5 AIR BAGS SEAT BELTS AND CHILD RESTRAINTS Top tether strap anchor P 1 38 Rear head restraints headrests P 1 7 Rear seat belts P 1 15 Roof mounted curtain side impact supplemental air bag P 1 42 Front seat mounted side impact supplemental air bags P 1 42 6 Front head restraints headrests P 1 7 7 Front seat belts P 1 15 8 Supplemental front impact air bags P 1 42 Seats P 1 2 10 Occupant classification sensor pattern sensor P 1 49 11 Seat belts with pretensioners P 1 55 12 LATCH Lower Anchors and Tethers for CHildren system P 1 26 See the page number indicated in paren theses for operating details PON gt 91 O 2 Illustrated table of contents EXTERIOR FRONT N m Ol e w Engine hood P 3 17 Windshield wiper and washer switch P 2 28 Windshield P 8 20 Moonroof if so equipped P 2 46 Power windows P 2 43 Door locks NISSAN Intelligent Key keys request button P 3 4 3 2 3 2 3 2 Mirrors P 3 25 Tire pressure P 8 32 Flat tire P 6 3 Tire chains P 8 40 Headlight and turn signal switch P 2 30 Replacing bulbs P 8 30 Fog light switch if so equipped P 8 27 See the page number indicated in paren theses for operating details illustrated table of contents 0 3 EXTERIOR REAR 0 4 Illustrated table of contents Rear
244. ent Installing child restraint LATCH lower anchor attachments LATCH compatible child restraints include two rigid or webbing mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle With this sys tem you do not have to use a vehicle seat belt to secure the child restraint Check your child re straint for a label stating that it is compatible with LATCH This information may also be in the in structions provided by the child restraint manu facturer Safety Seats seat belts and supplemental restraint system 1 27 LRS0662 LATCH rigid mounted attachment When installing a child restraint carefully read and follow the instructions in this manual and those supplied with the child restraint Top tether anchor point locations The child restraint top tether strap must be used when installing the child restraint with the LATCH lower anchor attachments or seat belts See In stalling top tether strap later in this section If you have any questions when installing a top tether strap child restraint consult your NISSAN dealer for details Anchor points 4 are located on the rear parcel shelf 1 28 Safety Seats seat belts and supplemental restraint system REAR FACING CHILD RESTRAINT INSTALLATION USING LATCH Refer to all Warnings and Cautions in the Child safety and Child restraints sections before in stalling a child restraint Follow these s
245. enter display changes to the USB memory mode 4 78 Monitor climate audio phone and voice recognition systems Operation keys To operate the USB memory select the desired key displayed on the display screen EE Pause Selectthe II key to pause the movie file To resume playing the movie file use the gt key Select the key to start playing the movie file or resume the movie file if it has been paused Select the E movie file gt l Next Chapter Fast Forward Select the PP key to skip the chapter s of the disc forward The chapters will ad vance the number of times the key is se lected Press and hold the key to fast for ward the chapter key to stop playing the jd Previous Chapter Rewind Select the M4 key to skip the chapter s of the disc backward The chapters will go back the number of times the key is selected Press and hold the key to rewind the chap ter List Select the List key on the movie file operation screen to display the file list USB gt Settings Settings Select the Settings key to adjust the following settings e Audio File Playback Switch to the audio playback mode This item is displayed only when the USB memory contains audio files Play Mode Choose between the Normal or 1 Track Repeat play modes 10 Key Search Select the 10 Key Search key to open the number entry screen Input the number you want to
246. er 0004 es 9 9 Vehicle identification number VIN plate 9 9 Vehicle loading information 9 12 Vehicle recovery a ee ee 6 13 Vehicle security system 2 26 Vehicle security system NISSAN vehicle immobi lizer system engine start 2 27 3 3 5 10 VentilatolS s ocd eee Ae ee ew wD 4 28 VISOS 6 eso ep eee ee ee ee a 3 25 Voice recognition system 4 116 Ww Warning Air bag warning light 1 57 2 14 Anti lock brake warning light 2 10 2 11 Battery charge warning light 2 11 Brake warning light 2 11 Engine oil pressure warning light 2 12 Hazard warning flasher switch 6 2 Low fuel warning light 2 13 2 24 Low tire pressure warning light 2 12 Low windshield washer fluid warning el a a ee a 2 24 Passenger air bag and status light 1 52 Seat belt warning light 2 14 Vehicle security system 2 26 Warning indicator lights and audible reminders aooaa we ae we we 2 10 Warning labels for SRS 1 57 Warning GINS s s s s sosa eo ee x Oe ow S 2 10 Washer switch Windshield wiper and washer switch 2 28 Weights See dimensions and weights 9 8 Wheels andtires 0004 8 33 Wheel tire size 2 ee ee ee 9 8 When traveling or registering your vehicle in another COURUY s lt 4 see babe Ae ew ad 9 9 Windows Locking passengers windows 2 45
247. eral purpose dishwashing liquid mixed with clean lukewarm never hot water 7 2 Appearance and care A CAUTION e Do not use car washes that use acid in the detergent Some car washes espe cially brushless ones use some acid for cleaning The acid may react with some plastic vehicle components causing them to crack This could affect their appearance and also could cause them not to function properly Always check with your car wash to confirm that acid is not used Do not wash the vehicle with strong household soap strong chemical deter gents gasoline or solvents Do not wash the vehicle in direct sun light or while the vehicle body is hot as the surface may become water spotted e Avoid using tight napped or rough cloths such as washing mitts Care must be taken when removing caked on dirt or other foreign sub stances so the paint surface is not scratched or damaged Rinse the vehicle thoroughly with plenty of clean water Inside flanges seams and folds on the doors hatches and hood are particularly vulnerable to the effects of road salt Therefore these areas must be cleaned regularly Take care that the drain holes in the lower edge of the door are open Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt A damp chamois can be used to dry the vehicle to avoid water spots WAXING Regular waxing protects the paint surface and helps retain new vehic
248. eration may remain in fast forward or rewind mode if it is con nected during a seek operation In this case please manually reset the iPod An iPod nano 2nd Generation will con tinue to fast forward or rewind if it is discon nected during a seek operation 4 40 Monitor climate audio phone and voice recognition systems An incorrect song title may appear when the Play Mode is changed while using an iPod nano 2nd Generation Audiobooks may not play in the same order as they appear on an iPod Large video files cause slow responses in an iPod The vehicle center display may mo mentarily black out but will soon recover fan iPod automatically selects large video files while in the shuffle mode the vehicle center display may momentarily black out but will soon recover Bluetooth streaming audio if so equipped Some Bluetooth audio devices may not be recognized by the in vehicle audio system It is necessary to set up the wireless con nection between a compatible Bluetooth audio device and the in vehicle Bluetooth module before using the Bluetooth audio Operating procedure of the Bluetooth au dio will vary depending on the devices Make sure how to operate your audio device be fore using it with this system The Bluetooth audio may be stopped un der the following conditions Receiving a call on the Hands Free Phone System Checking the connection to the h
249. erly adjust the head restraint headrest before an occupant uses the seating posi tion For adjustable head restraint headrest Adjust the head restraint headrest so the center is level with the center of your ears If your ear position is still higher than the recommended alignment place the head restraint headrest at the highest position Safety Seats seat belts and supplemental restraint system 1 9 For non adjustable head restraint To raise the head restraint headrest headrest pull it up Make sure the head restraint headrest is posi Make sure the head restraint headrest is posi tioned so the lock knob is engaged in the notch tioned so the lock knob is engaged in the notch before riding in that designated seating position before riding in that designated seating position 1 10 Safety Seats seat belts and supplemental restraint system To lower push and hold the lock knob and push the head restraint headrest down Make sure the head restraint headrest Is posi tioned so the lock knob is engaged in the notch before riding in that designated seating position REAR SEAT HEAD RESTRAINTS HEADRESTS AWARNING Head restraints headrests supplement the other vehicle safety systems They may provide additional protection against injury in certain rear end colli sions Adjust the head restraints headrests properly as speci fied in this section Check the adjust ment after someone else uses the seat Do n
250. ery will be charged while connected to the vehicle with the ignition switch in the ACC or ON position While connected to the vehicle the iPod can only be operated by the vehicle audio controls To disconnect the iPod from the vehicle re move the USB end of the cable from the USB jack on the vehicle then remove the cable from the iPod iPod is a trademark of Apple Inc registered in the U S and other countries Compatibility The following models are compatible iPod 5th Generation firmware version 1 2 3 or later iPod Classic firmware version 1 1 1 or later iPod Touch firmware version 2 0 0 or later iPod nano 1st generation firmware ver sion 1 3 1 or later iPod nano 2nd generation firmware ver sion 1 1 3 or later iPod nano 3rd generation firmware ver sion 1 1 3 or later iPod nano 4th generation firmware ver sion 1 0 4 or later iPod nano 5th generation firmware ver sion 1 0 1 or later Some features of this iPod may not be fully functional Make sure that your iPod firmware is updated to the version indicated above 8 00 S Artist XXXXXX Album XXXXXX Track XXXXXX Shuffle Songs Repeat All Track 1 of 23 L 2 10 Menu hil Audio main operation Place the ignition switch in the ACC or ON position Press the DISC AUX button repeatedly to switch to the iPod mode If the system has been turned off
251. es cellular phone antenna and body etc REGULATORY INFORMATION FCC Regulatory information CAUTION To maintain compliance with FCC s RF exposure guidelines use only the supplied antenna Unauthorized antenna modification or attachments could damage the transmitter and may violate FCC regula tions Operation is subject to the following two con ditions 1 This device may not cause interference and 2 this device must accept any interference including interference that may cause unde sired operation of the device Monitor climate audio phone and voice recognition systems 4 93 IC Regulatory information Operation is subject to the following two con ditions 1 this device may not cause interfer ence and 2 this device must accept any interference including interference that may cause undesired operation of the device This Class B digital apparatus meets all re quirements of the Canadian Interference Causing Equipment Regulations BLUETOOTH is a trademark owned by Bluetooth SIG Inc and licensed to Visteon USING THE SYSTEM The NISSAN Voice Recognition system allows hands free operation of the Bluetooth Phone System amp Bluetooth If the vehicle is in motion some commands may not be available so full attention may be given to vehicle operation Initialization When the ignition switch is placed in the ON position NISSAN Voice Recognition is initialized whic
252. es may sometimes interfere with FM station reception even if the FM station is within 25 mi 40 km The strength of the FM signal is directly related to the distance between the transmitter and receiver FM signals follow a line of sight path exhibiting many of the same char acteristics as light For example they will reflect off objects Fade and drift As your vehicle moves away from a station transmitter the signals will tend to fade and or drift Monitor climate audio phone and voice recognition systems 4 35 Static and flutter During signal interference from buildings large hills or due to antenna position usually in conjunction with increased distance from the station transmitter static or flutter can be heard This can be reduced by adjusting the treble control to reduce treble response Multipath reception Because of the reflective characteristics of FM signals direct and reflected signals reach the receiver at the same time The signals may cancel each other resulting in mo mentary flutter or loss of sound AM RADIO RECEPTION AM signals because of their low frequency can bend around objects and skip along the ground In addition the signals can be bounced off the ionosphere and bent back to earth Because of these characteristics AM signals are also sub ject to interference as they travel from transmitter to receiver Fading Occurs while the vehicle is passing through freeway underpasses or in areas
253. eset Fuel Eco to reset the fuel economy calcula tion to O Resetting fuel economy The average fuel economy calculation can be reset to 0 Press the INFO button and select the Fuel Economy key then select the Reset Fuel Eco key using the NISSAN controller Fuel Economy Record Select the View key to display the average fuel consumption history in a graph form Maintenance Items Press the INFO button and select the Maintenance key using the NISSAN controller the maintenance information will be dis played on the screen Reminder keys Can choose betweeen Engine Oil Oil Filter Tire and Other Reminder Displays the interval for the selected reminder Select the or keys to adjust the distance up or down Resetting the maintenance Resets the distance for the selected reminder to O mi km interval Displaying the maintenance Displays status of the selected interval reminder Select to toggle on or off If set to On the maintenance notice screen will be notice reminder displayed once the interval is met and the ignition switch is placed in the OFF and then ON position Where am See the separate Navigation System Owner s Manual for information regarding this item Other Options For Voice Recognition settings refer to NISSAN Voice Recognition system in this section For GPS Position refer to the separate Navigation System Owner s manual 4 16 Monitor climate audio phone and voi
254. essing the amp button on the steering wheel After interrupting the system wait for a beep before speaking your command 4 108 Monitor climate audio phone and voice recognition systems One Shot Call To use the system faster you may speak the second level commands with the main menu command on the main menu For example press the amp button and after the tone say Call Redial NOTE Voice recognition system must be in Alter nate Command Mode in order for One Shot Calling to operate See NISSAN Voice Recognition Alternate Command Mode for more information CONNECTING PROCEDURE settings 8 00 To connect a Bluetooth device use one of the following methods Press the Phone button on the control panel or the button on the steering wheel then select the Connect Phone key on the display Press the SETTING button on the control panel then select the Bluetooth key on the display Adjust navigation settings LHA1236 Bluetooth ON OFF Allows user to switch Bluetooth on and off Bluetooth must be on in order to connect device re Turns Bluetooth off Connect Bluetooth Upon pressing this button a popup box will appear on the screen prompting you to confirm that the connection is for the phone system Select the Yes key Confirms that you are connecting a Bluetooth device Upon pressing this button the following message will appear on screen The sy
255. ether strap in this section Do not install child restraints that require the use of a top tether strap in seating positions that do not have a top tether anchor 1 36 Safety Seats seat belts and supplemental restraint system LRSO667 Forward facing step 4 4 Pull the shoulder belt until the belt is fully extended At this time the seat belt retractor is in the Automatic Locking Retractor ALR mode child restraint mode It reverts to Emergency Locking Retractor ELR mode when the seat belt is fully retracted LRS0668 Forward facing step 5 5 Allow the seat belt to retract Pull up on the shoulder belt to remove any slack in the belt 6 WRS0681 Forward facing step 6 Remove any additional slack from the seat belt press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt Tighten the tether strap according to the manufacturer s instructions to remove any slack WRS0698 Forward facing step 8 After attaching the child restraint test it be fore you place the child in it Push it from side to side while holding the child restraint near the seat belt path The child restraint should not move more than 1 inch 25 mm from side to side Try to tug it forward and check to see if the belt holds the restraint in place If the restraint is not secure tighten the seat bel
256. ew Moni tor may differ somewhat from those of the actual object Objects on the monitor may not be clear ina dark place or at night This is not a malfunc tion If dirt rain or snow attaches to the camera the RearView Monitor may not clearly display objects Clean the camera Do not use wax on the camera window Wipe off any wax with a clean cloth damp ened with mild detergent diluted with water Monitor climate audio phone and voice recognition systems 4 27 VENTS LHA1132 LHA1133 Center Side Adjust air flow direction by moving the vent slides Open or close the vents by using the dial Move the dial toward the to open the vents or toward the K to close them 4 28 Monitor climate audio phone and voice recognition systems Hono Oooo je i 4 nja nn mju afufa juju Rear LHA1134 HEATER AND AIR CONDITIONER automatic Type A Oo RON Type A Temperature control buttons driver s 9 side AUTO climate control ON button 10 VY front defroster button 11 7 amp 2 Air recirculation button MODE manual air flow control button Temperature control buttons passen ger s side DUAL passenger side temperature control ON OFF button amp D Fresh air intake button LHA1139 fan speed control dial ON OFF button Ut rear window defroster button A C air conditioner ON OFF button AWARNING The air conditioner cooling function
257. ey code enter 1234 from the handset The Passkey code 1234 has been assigned by NISSAN and cannot be changed The system asks you to say a name for the phone If the name is too long or too short the system tells you then prompts you for a name again Also if more than one phone is connected and the name sounds too much like a name already used the system tells you then prompts you for a name again Making a call by entering a phone number Main Menu Call Phone Number Speak the digits Dial Say Call The system acknowledges the command and announces the next set of available commands Say Phone Number The system ac knowledges the command and announces the next set of available commands Say Special Number to dial more than 10 digits or any special characters Say the number you wish to call starting with the area code in single digit format If the system has trouble recognizing the correct phone number try entering the number in the following groups 3 digit area code 3 digit prefix and the last 4 digits For ex ample 555 121 3354 can be said as five five five as the 1st group then one two one as the 2nd group and three three five four as the 3rd group For dialing more than 10 digits or any special characters say Special Number See How to say num bers in this section for more
258. f the seat The climate control switch is located on the center console The climate controlled seat can be operated as follows 1 Start the engine 2 Turn the control knob to the H Heat side or to the C Cool side as desired The indica tor light on the control knob will illuminate 3 Adjust the desired amount of air using the control knob The climate controlled seat blower remains on low speed for approxi 2 36 Instruments and controls mately 60 seconds after turning the switch on or selecting the desired temperature 4 When the vehicle s interior is warmed or cooled or before you leave the vehicle be sure to turn the control knob to the Off center position To check the air filter for the climate controlled seat contact a NISSAN dealer AWARNING Do not use or allow occupants to use the climate controlled seats if you or the oc cupants can not monitor seat tempera tures or have an inability to feel pain in those body parts in contact with the seat Use of the climate controlled seats by such people could result in serious injury A CAUTION The battery could run down if the cli mate control seat is operated while the engine is not running Do not use the climate control seat for extended periods or when no one is using the seat Do not put anything on the seat which insulates heat such as a blanket cush ion seat cover etc Otherwise the seat may become overheated Do not pla
259. far as practical away from the side air bag Rear seat passengers should be seated as far away as practical from the door finishers and side roof rails The side air bags and curtain air bags inflate 1 54 Safety Seats seat belts and supplemental restraint system quickly in order to help protect the occupants Because of this the force of the side air bag and curtain side impact air bag inflating can increase the risk of injury if the occupant is too close to or is against these air bag modules during inflation The side air bag and curtain air bags will deflate quickly after the collision is over The side air bags and curtain air bags op erate only when the ignition switch is placed in the ON or START position After placing the ignition switch in the ON position the supplemental air bag warning light illuminates The supplemental air bag warning light will turn off after about 7 sec onds if the system is operational AWARNING Do not place any objects near the seat back of the front seats Also do not place any objects an umbrella bag etc between the front door finisher and the front seat Such objects may become dangerous projectiles and cause injury if a side air bag inflates Right after inflation several side air bag and curtain air bag system components will be hot Do not touch them you may severely burn yourself No unauthorized changes should be made to any components or wiring of the side air
260. ference The lines are highly affected by the number of occupants fuel level vehicle position road conditions and road grade If the tires are replaced with different sized tires the predicted course lines may be displayed incorrectly e On a snow covered or slippery road there may be a difference between the predicted course line and the actual course line If the battery is disconnected or be comes discharged the predicted course lines may be displayed incorrectly If this occurs please perform the follow ing procedures Turn the steering wheel from lock to lock while the engine is running Drive the vehicle on a straight road for more than 5 minutes When the steering wheel is turned with the ignition switch in the ACC position the predicted course lines may be dis played incorrectly The distance guide line and the vehicle width line should be used as a reference only when the vehicle is on a level paved surface The distance viewed on the monitor is for reference only and may be different than the actual dis tance between the vehicle and dis played objects When backing up the vehicle up a hill objects viewed in the monitor are fur ther than they appear When backing up the vehicle down a hill objects viewed in the monitor are closer than they ap pear Use the inside mirror or glance over your shoulder to properly judge distances to other objects The vehicle width and pred
261. ff Press the button again to turn the display on CONTROL PANEL BUTTONS COLOR SCREEN WITH NAVIGATION SYSTEM if so equipped 10 brightness control button 11 VOICE button 12 SETTING button P 4 17 13 MAP button 14 5 BACK previous button P 4 12 15 ZOOM IN button For Navigation system control buttons refer to the separate Navigation System Owner s Manual For information on the PHONE button see Bluetooth Hands Free Phone System with Navigation System in this section When you use this system make sure the engine is running If you use the system with the engine not running ignition ON or ACC for a long time it will discharge the battery and the engine will not start Reference symbols INFO button P 4 15 ENTER button This is a button on the control PHONE button panel DEST button brightness control button Example Words marked in quotes refer to a n 7 key shown only on the display These keys can be aude 3 2 OFF brightness control button P selected by touching the screen or using the NISSAN controller P 4 12 4 19 NISSAN controller Monitor climate audio phone and voice recognition systems 4 11 ZOOM OUT button STATUS button P 4 15 oe E E o 2 HOW TO USE THE NISSAN CONTROLLER Use the NISSAN controller to choose an item on the display screen Highlight an item on the dis play using the main directional b
262. for assistance AIR CLEANER The air cleaner filter should not be cleaned and reused Replace it according to the maintenance log shown in the NISSAN Service and Mainte nance Guide When replacing the filter wipe the inside of the air cleaner filter housing and the cover with a damp cloth To remove the air cleaner filter Unlatch the clips and move the air cleaner cover upward Remove the air cleaner filter Wipe the inside of the air cleaner filter hous ing and cover with a damp cloth AWARNING e Operating the engine with the air cleaner removed can cause you or oth ers to be burned The air cleaner not only cleans the air it stops the flame if the engine backfires If it isn t there and the engine backfires you could be burned Do not drive with the air cleaner removed and be careful when working on the engine with the air cleaner removed Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed Doing so could result in serious injury IN CABIN MICROFILTER The in cabin microfilter restricts the entry of air borne dust and pollen particles and reduces some objectionable outside odors The filter is located behind the glove box Refer to the NISSAN Service and Maintenance Guide for change intervals If replacement is required see your NISSAN dealer Maintenance and do it yourself 8 19 WINDSHIELD WIPER BLADES CLEANING If your
263. ft the transmission into gear Release the parking brake Drive slowly until the vehicle and trailer are clear from the blocks Apply and hold the brake pedal Have someone retrieve and store the blocks While going downhill the weight of the trailer pushing on the tow vehicle may de crease overall stability Therefore to main tain adequate control reduce your speed and use the manual shift mode M5 Avoid long or repeated use of the brakes when descending a hill as this reduces their effec tiveness and could cause overheating Shift ing the manual shift mode to M5 5th pro vides engine braking and reduces the need to brake as frequently If the engine coolant temperature rises to a high temperature refer to If your vehicle overheats in the In case of emergency section of this owner s manual Trailer towing requires more fuel than normal circumstances Avoid towing a trailer for your vehicle s first 500 miles 805 km For the first 500 miles 805 km that you do tow do not drive over 50 MPH 80 km h Have your vehicle serviced more often than at intervals specified in the recommended Maintenance Schedule in the NISSAN Ser vice and Maintenance Guide When making a turn your trailer wheels will be closer to the inside of the turn than your vehicle wheels To compensate for this make a larger than normal turning radius during the turn Crosswinds and rough roads will adversely
264. fts into the armed phase The security light begins to flash once every 3 seconds If during the 30 second pre arm time period the driver s door is unlocked by the key or the keyfob or the ignition switch is placed in the ACC or ON position the sys tem will not arm Even when the driver and or passen gers are in the vehicle the system will activate with all the doors hood and trunk lid locked with the ignition switch placed in the LOCK position When placing the ignition switch in the ACC or ON position the system will be re leased Vehicle security system activation The vehicle security system will give the following alarm The headlights blink and the horn sounds intermittently The alarm automatically turns off after a pe riod of time However the alarm reactivates If the vehicle is tampered with again The alarm can be shut off by unlocking the driver s door or trunk lid with the key or by pressing the button on the Intelligent Key The alarm is activated by opening the door or trunk lid without using the key or Intelligent Key even if the door is unlocked by releasing the door inside lock switch How to stop an activated alarm The alarm stops only by unlocking the driver s door or the trunk lid with the key pressing the button onthe Intelligent Key or press ing the request switch on the driver s or passen ger s door with the Intelligent Key in range of the door handle NISS
265. fusible links If any of these fusible links are melted replace with only Genuine NISSAN parts PASSENGER COMPARTMENT A CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover This could damage the electrical system or cause a fire 8 24 Maintenance and do it yourself If any electrical equipment does not operate check for an open fuse 1 Be sure the ignition switch and the headlight switch are OFF 2 Pull the fuse box cover to remove 3 Remove the fuse with the fuse puller WDI0452 Type A If the fuse is open replace it with an equivalent good fuse 5 Push the fuse box cover to install 6 If a new fuse also opens have the electrical system checked and repaired by a NISSAN dealer Type B LDI0456 Extended storage switch If any electrical equipment does not operate remove the extended storage switch and check for an open fuse NOTE The extended storage switch is used for long term vehicle storage Even if the ex tended storage switch is broken it is not necessary to replace it Replace only the open fuse in the switch with a new fuse How to replace the extended storage switch 1 To remove the extended storage switch be sure the ignition switch is in the OFF or LOCK position 2 Be sure the headlight switch is in the OFF position 3 Remove the fuse box cover 4 Pinch the locking tabs found on each
266. g Add a washer solvent to the washer for better cleaning In the winter season add a windshield washer antifreeze Follow the manufacturer s in structions for the mixture ratio Refill the reservoir more frequently when driving conditions require an increased amount of windshield washer fluid Recommended fluid is Genuine NISSAN Wind shield Washer Concentrate Cleaner amp Anti freeze or equivalent A CAUTION e Do not substitute engine anti freeze coolant for windshield washer fluid This may result in damage to the paint Do not fill the windshield washer fluid reservoir with washer fluid concen trates at full strength Some methyl al cohol based washer fluid concentrates may permanently stain the grille if spilled while filling the windshield washer reservoir e Pre mix washer fluid concentrates with water to the manufacturer s recom mended levels before pouring the fluid into the windshield washer fluid reser voir Do not use the windshield washer fluid reservoir to mix the washer fluid concentrate and water BATTERY Keep the battery surface clean and dry Clean the battery with a solution of baking soda and water Make certain the terminal connections are clean and securely tightened If the vehicle is not to be used for 30 days or longer disconnect the negative battery terminal cable to prevent discharge NOTE Care should be taken to avoid situations that can lead to potential ba
267. g text might be displayed Folder displays the name of the current folder being accessed File displays the name of the file currently playing Song displays the ID3 encoded tag of the song name Album displays the ID3 encoded tag of the album name Artist displays the ID3 encoded tag of the artist s name Some of this text might not display while playing a regular CD FM AM SAT radio operation FM AM band select Pressing the FM AM button will change the band as follows AM FM1 FM2 AM When the FM AM button is pressed while the ignition switch is in the ACC or ON position the radio will come on at the station last played The last station played will also come on when the VOL ON OFF control knob is pressed ON If a compact disc is playing when the FM AM button is pressed the compact disc will auto matically be turned off and the last radio station played will come on Monitor climate audio phone and voice recognition systems 4 65 The FM stereo indicator STEREO will illuminate during FM stereo reception When the stereo broadcast signal is weak the radio will automati cally change from stereo to monaural reception SAT band select Pressing the SAT button will change the band as follows XM1 XM2 XM3 XM1 satellite if so equipped When the SAT button is pressed while the igni tion switch is in the ACC or ON position the radio will come on at the statio
268. g the programmed information Reprogramming a single HomeLink button If your vehicle is stolen 2 02 000e INSTRUMENT PANEL 8 Shift paddles if so equipped P 5 15 9 Windshield wiper washer switch P 2 28 Display screen Navigation system an a 10 eee oo if so equipped P 4 11 11 Display screen Navigation system controls if so equipped P 4 11 12 Front passenger supplemental air bag P 1 56 eee 13 Glove box P 2 41 e 14 Display screen models without Navigation system P 4 4 15 Climate controls models without Navigation system P 4 29 16 Audio system controls models without iL Navigation system P 4 35 17 Front passenger air bag status light r eaen P 1 49 18 Audio system controls P 4 35 19 Climate controls models with Navigation system P 4 32 20 Shift lever P 5 12 1 Side and center vents P 4 28 4 Meters and gauges P 2 3 2 Headlight fog light if so equipped turn 5 Driver supplemental air bag horn oh Hazard nee Anner AG P 6 2 signal switch P 2 30 P 1 42 P 2 34 22 Ignition switch behind the steering 3 Steering wheel switch for audio control 6 Security indicator light P 2 26 wheel P 5 7 and Bluetooth Hands Free Phone 7 Cruise control main set switches 23 _Tilt telescopic steering wheel controls System P 4 89 4 92 P 5 19 if so equipped P 3 22 2 2
269. ght assembly just before a replacement bulb is installed Only touch the base when handling the bulb Never touch the glass envelope Touching the glass could significantly affect bulb life and or headlight performance e High pressure halogen gas is sealed inside the halogen bulb The bulb may break if the glass envelope is scratched or the bulb is dropped Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash A temperature difference between the inside and the outside of the lens causes the fog This is not a malfunction If large drops of water collect inside the lens contact a NISSAN dealer Maintenance and do it yourself 8 27 FRONT PARK TURN SIDEMARKER LIGHT Bulb replacement requires the removal of the headlight assembly If replacement is required see your NISSAN dealer FOG LIGHTS if so equipped Replacing the fog light bulb If replacement is required see your NISSAN dealer A CAUTION High pressure halogen gas is sealed inside the halogen bulb The bulb may break if the glass envelope is scratched or the bulb is dropped When handling the bulb do not touch the glass envelope e Use the same number and wattage as Originally installed as shown in the chart Do not leave the bulb out of the fog light for a long period of time as dust mois ture and smoke may enter the fog light body and affect the performance of the fog light 8 28 Maintenance an
270. ght for the front passenger Refer to Seat belts in the Safety Seats seat belts and supplemental restraint system section for precautions on seat belt usage Se Supplemental air bag warning light When the ignition switch is placed in the ON or START position the supplemental air bag warn ing light illuminates for about 7 seconds and then turns off if the SRS air bag systems are opera tional This means the system is operational If any of the following conditions occur the air bags and or pretensioner systems need servic ing and your vehicle must be taken to a NISSAN dealer The supplemental air bag warning light re mains on after approximately 7 seconds The supplemental air bag warning light flashes intermittently The supplemental air bag warning light does not come on at all Unless checked and repaired the supplemental restraint systems air bag systems and or the pretensioners may not function properly For ad ditional details see Supplemental restraint sys tem in the Safety Seats seat belts and supplemental restraint system section of this manual AWARNING If the supplemental air bag warning light is on it could mean that the front air bag side air bag curtain air bag systems and or pretensioner systems will not op erate in an accident To help avoid injury to yourself or others have your vehicle checked by a NISSAN dealer as soon as possible INDICATOR LIGHTS
271. ght timer illuminates for a period of time when a door is unlocked and the room light switch is in the DOOR position 3 12 Pre driving checks and adjustments Opening the trunk lid 1 Push the trunk opener request switch for more than 1 second while carrying the Intel ligent Key with you 2 The trunk will unlatch A chime will sound 4 times 3 Raise the trunk lid to open the trunk Lockout protection To prevent the Intelligent Key from being acci dentally locked in the trunk lockout protection is equipped with the Intelligent Key When all doors are locked and the trunk lid is closed with the Intelligent Key inside the trunk the outside buzzer will sound and the trunk will open HOW TO USE THE REMOTE KEYLESS ENTRY FUNCTION The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key The remote keyless function can operate at a distance of 33 ft 10 m away from the vehicle The operating distance de pends upon the conditions around the vehicle The remote keyless entry function will not func tion under the following conditions When the Intelligent Key is not within the operational range When the doors or the trunk are open or not closed securely When the Intelligent Key battery is dis charged CAUTION When locking the doors using the Intelli gent Key be sure not to leave the key in the vehicle Ay A 1 Place the ign
272. gs and driving 5 7 Push Button Ignition Switch 0 0 cece eee 5 7 Operating range aca eotwectant anerer rrr 5 8 Push button ignition switch positions 5 8 Emergency engine shut off 00005 5 9 NISSAN Intelligent Key battery discharge 5 9 NISSAN vehicle immobilizer system 5 10 Before starting the engine 2 205 5 11 Starting the engine w icxctcorwadesen nananana 5 11 Driving the vehicle 0 00e eee eee eee 5 12 Continuously Variable Transmission CVT 5 12 Parking Drak vcaesccnecscennaseeeant seceyuecee es 5 18 Cruise COMUOl sic ctendcateastgrtesteaesmneeten aes 5 19 Precautions on cruise control 5 19 Cruise control operations 2 002 00 5 19 Break in schedule 0 200 e eee eee eee 5 21 Fuel efficient driving tipS 02 02e eee ee 5 21 Increasing fuel economy 0022 eee eee 5 22 Parking parking on DINS 22 2 lt es cen eohdu pee keeeee nt 5 23 POWER Steer Gree diet ieren n aeeeee eae es 5 24 Brake Sy olelll svacereacsocechucestteceesneseeres ac 5 24 Brake precautions i225 asecad aasan nanana 5 24 Anti lock Braking System ABS 0005 5 25 Vehicle Dynamic Control VDC system 5 26 Cold weather driving 00e eee eee eee es 5 28 Freeing a frozen door lock 00 cee eee 5 28 ANUIANIGEZE iu E E E 5 28 BARY eege aa E aa
273. guage of the menus on the display screen If you select the Francais key French language screens will be displayed so please use the French Owner s Manual To obtain a French Owner s Manual please see Owner s Manual Service Manual Order Informa tion in the Technical and consumer information section Select Units Changes the units used to US mi F MPG or Metric km C L 100km Voice Recognition See NISSAN Voice Recognition system in this section Camera Settings Selecting the Camera key will bring up the Camera settings screen Image Viewer See Image viewer in this section Navi See the separate Navigation System Owner s Manual for more information gation Audio See Audio system in this section for more information Phone See Bluetooth Hands Free Phone System with Navigation System in this section Bluetooth See Bluetooth Hands Free Phone System with Navigation System in this section Volume amp Beeps Adjusts the volume and beep settings See the separate Navigation System Owner s Manual for more information Phone Volume See Bluetooth Hands Free Phone System with Navigation System in this section Switch Beeps Toggles on or off the beep sound that is heard when a control panel button is pressed D gt OFF BUTTON Press and hold the t 2 OFF button for more than two seconds to turn the display off Press the button again to turn the display on To
274. h the vehicle as it receives radio waves The Intel ligent Key system transmits weak radio waves Environmental conditions may interfere with the operation of the Intelligent Key system under the following operating conditions When operating near a location where strong radio waves are transmitted such as a TV tower power station and broadcasting station When in possession of wireless equipment such as a cellular telephone transceiver and CB radio When the Intelligent Key is in contact with or covered by metallic materials When any type of radio wave remote control is used nearby When the Intelligent Key is placed near an electric appliance such as a personal com puter When the vehicle is parked near a parking meter In such cases correct the operating conditions before using the Intelligent Key function or use the mechanical key Although the life of the battery varies depending on the operating conditions the battery s life is approximately 2 years If the battery is dis charged replace it with a new one When the Intelligent Key battery is almost dis charged insert the Intelligent Key into the Intelli gent Key port to start the engine Replace the discharged battery with a new one as soon as possible For additional information see Push Button Ignition Switch in the Starting and driv ing section Since the Intelligent Key is continuously receiving radio waves if the ke
275. h takes a few seconds Ifthe fi button is pressed before the initialization completes the system will announce Hands free phone system not ready and will not react to voice commands Operating tips To get the best performance out of the NISSAN Voice Recognition system observe the following Keep the interior of the vehicle as quiet as possible Close the windows to eliminate surrounding noises traffic noises vibration sounds etc which may prevent the system from recognizing voice commands correctly Wait until the tone sounds before speaking a command Otherwise the command will not be received properly Start speaking a command within 5 seconds after the tone sounds Speak in a natural voice without pausing between words 4 94 Monitor climate audio phone and voice recognition systems Giving voice commands To operate NISSAN Voice Recognition press and release the 4 button located on the steering wheel After the tone sounds speak a command The command given is picked up by the micro phone and voice feedback is given when the command is accepted If you need to hear the available commands for the current menu again say Help and the system will repeat them fa command is not recognized the system announces Command not recognized Please try again Make sure the command is said exactly as prompted by the system and repeat the command in a clear voice If you want to
276. hat towing a trailer places additional loads on your vehicle s engine drive train steering brak ing and other systems A NISSAN Towing Guide U S only is available on the website at www nissanusa com This guide includes information on trailer towing ca pability and the special equipment required for proper towing 9 16 Technical and consumer information MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed the value specified in the Towing Load Specification chart found later in this sec tion The total trailer load equals trailer weight plus its cargo weight When towing a trailer load of 1 000 Ibs 454 kg or more trailers with a brake system must be used The Gross Combined Weight Rating GCWR equals the combined weight of the towing vehicle including passengers and cargo plus the total trailer load Towing loads greater than these or using Improper towing equipment could ad versely affect vehicle handling braking and per formance The ability of your vehicle to tow a trailer is not only related to the maximum trailer loads but also the places you plan to tow Tow weights appro priate for level highway driving may have to be reduced for low traction situations for example on slippery boat ramps Temperature conditions also can affect towing For example towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and c
277. have an Intelligent Key with you Carry an Intelligent Key with you 2 When the door is closed with the Intelligent Key left outside the vehicle and the ignition switch is placed in the ACC or ON position A chime will also sound Parking brake warning This warning illuminates when the parking brake is set and the vehicle is driven SHIFT P warning This warning illuminates when the ignition switch is pushed to stop the engine with the shift lever in any position except in the P Park position If this warning illuminates the ignition switch is in the OFF position Move the shift lever to the P Park position or push the ignition switch to the ON position An inside warning chime will also sound If the shift lever is moved to the P Park position the Push warning will appear Refer to Push warning in this section For additional information about Intelligent Key see NISSAN Intelligent Key in the Pre driving checks and adjustments section Engine start operation indicator This indicator illuminates when the ignition switch is in the LOCK OFF ACC or ON position with the shift lever in the P Park position This indicator means that the engine will start by pushing the push button ignition switch with the brake pedal depressed NISSAN Intelligent Key insertion indica tor This indicator illuminates when the Intelligent Key needs to be inserted into the Intelligent Key port For exa
278. he ABS includes electronic sensors electric pumps hydraulic solenoids and a computer The computer has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse When the self test occurs you may hear a clunk noise and or feel a pulsation in the brake pedal This is normal and does not indicate a malfunction If the computer senses a malfunc tion it switches the ABS off and illuminates the ABS warning light on the instrument panel The brake system then operates normally but without anti lock assistance If the ABS warning light illuminates during the self test or while driving have the vehicle checked by a NISSAN dealer Normal operation The ABS operates at speeds above 3 6 MPH 5 10 km h The speed varies according to road conditions Starting and driving 5 25 When the ABS senses that 1 or more wheels are close to locking up the actuator rapidly applies and releases hydraulic pressure This action is similar to pumping the brakes very quickly You may feel a pulsation in the brake pedal and hear a noise from under the hood or feel a vibration from the actuator when it is operating This is normal and indicates that the ABS is operating properly However the pulsation may indicate that road conditions are hazardous and extra care is re quired while driving 5 26 Starting and driving VEHICLE DYNAMIC CONTROL VDC SYSTEM The
279. he Voice Recognition system starts The system requests that you repeat a com mand after a tone This command is also displayed on the screen After the tone sounds and the icon on the screen changes from to B speak the command that the system requested When the system has recognized the voice command the voice of the user is learned switch or the BACK button to return to the previous screen If the system has learned the command correctly the voice command indicator on the screen turns on Speaker Adaptation function settings To access the speaker adaptation function set tings 1 oP og R WN Press the SETTING button on the control panel Select the Others key Select the Voice Recognition key Select the Speaker Adaptation key Select the user Select the Setting key Edit User Name Edit the user name using the keypad displayed on the screen Delete Voice Data Deletes the user s voice results that the Voice Recognition system has learned Continuous Learning When this item is turned to ON you can have the system learn the voice commands in succession without selecting commands one by one Monitor climate audio phone and voice recognition systems 4 135 TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty If problems are en countered follow the solutions given in this guide for the appropriate error Where
280. he harness equipped forward facing child re straint NISSAN recommends that the child be placed in a commercially available booster seat to obtain proper seat belt fit For a seat belt to fit properly the booster seat should raise the child so that the shoulder belt is properly positioned across the chest and the top middle portion of the shoulder The shoulder belt should not cross the neck or face and should not fall off the shoul der The lap belt should lie snugly across the lower hips or upper thighs not the abdomen A booster seat can only be used in seating posi tions that have a three point type seat belt The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Mo tor Vehicle Safety Standards Once the child has grown so the shoulder belt is no longer on or near the face and neck and the lap belt can be posi tioned properly across the lower hips or upper thighs use the seat belt without the booster seat AWARNING Never let a child stand or kneel on any seat and do not allow a child in the cargo area The child could be seriously injured or killed in a sudden stop or collision CHILD RESTRAINTS PRECAUTIONS ON CHILD RESTRAINTS 1 24 Safety Seats seat belts and supplemental restraint system AWARNING Failure to follow the warnings and in structions for proper use and installa tion of child restraints could result in serio
281. he last radio station played will come on TUNE FOLDER Tuning knob To manually tune the radio turn the TUNE FOLDER knob to the right or left 44 gt gt SEEK CAT and TRACK tuning buttons Press the SEEK CAT M4 button or the TRACK gt P button to tune from high to low or low to high frequencies and stop at the next broadcasting station SCAN tuning Press the SCAN button to stop at each broad casting station for 5 seconds Pressing the SCAN button again during this five second pe riod will stop scan tuning and the radio will remain tuned to that station If the SCAN button is not pressed within 5 seconds scan tuning moves to the next station 1 to 6 Station memory operations Six stations can be set for the AM band Twelve stations can be set for the FM band 6 for FM1 6 for FM2 Eighteen stations can be set for the XM band 6 for XM1 6 for XM2 6 for XM3 1 Choose the radio band AM FM1 or FM2 using the FM AM select button or choose the satellite band SAT1 or SAT2 using the AUX button 2 Tune to the desired station using manual SEEK or SCAN tuning Press and hold any of the desired station memory buttons 1 6 until a beep sound is heard 3 The channel indicator will then come on and the sound will resume Programming is now complete 4 Other buttons can be set in the same man ner If the battery cable is disconnected or if the fuse opens the radio memory will be canceled In th
282. he recognition success rate may be affected as the number of available commands and ways of speaking each command are increased You can turn this mode ON or OFF When this mode is activated the Voice Recognition Settings will change to show more options Activating Alternate Command Mode 1 Press the SETTING button on the control panel Select the Others key on the display Select the Voice Recognition key Select the Alternate Command Mode key of oN The confirmation message is displayed on the screen Select the OK key to activate the Alternate Command Mode 6 Alternate Command Mode is activated and the setting menu is expanded to include the Alternate Command Mode options See Voice Recognition Settings in this section for an explanation of the options Displaying the command list If you are controlling the system by voice com mands for the first time or do not know the appropriate voice command perform the follow ing procedure for displaying the voice command list available only in Alternate Command Mode Press the switch listen for the tone and say Help The system will respond by display ing the command list main menu Only manual controls such as the touchscreen can navigate the command list menu As an alternative to the voice command Help you may access the command list using the fol lowing steps 1 Press the SETTING button on the control pan
283. he tie down hooks for towing or vehicle recovery Rocking a stuck vehicle A WARNING Stand clear of a stuck vehicle e Do not spin your tires at high speed This could cause them to explode and result in serious injury Parts of your vehicle could also overheat and be damaged If your vehicle is stuck in sand snow mud etc use the following procedure 1 Turn off the Vehicle Dynamic Control VDC system 2 Make sure the area in front and behind the vehicle is clear of obstructions 3 Turn the steering wheel right and left to clear an area around the front tires Slowly rock the vehicle forward and back ward Shift back and forth between R Reverse and D Drive Apply the accelerator as little as possible to maintain the rocking motion Release the accelerator pedal before shifting between R Reverse and D Drive Do not spin the tires above 35 MPH 55 km h If the vehicle cannot be freed after a few tries contact a professional towing service to remove the vehicle In case of emergency 6 13 MEMO 6 14 Incase of emergency 7 Appearance and care Cleaning exterior 0 00 eee eee 7 2 Air fresheners son ecc keen de neat ee eeeeerieaerands 7 5 NV ASOING ones pedis teceeseesh beeueeseersen lt 7 2 DEA EEE E E E E E T 7 5 aeeie scucores ican veinen we aahan es oenesaadee ates 1 2 PDE oE AA AEE R 7 6 REMOVING SPOS ania T aaia AA E e sa 7 3 Corrosion POGOe tc srera cire
284. hear and feel the latch engage Be sure to follow the child restraint manufacturer s in structions for belt routing Safety Seats seat belts and supplemental restraint system 1 31 LRSO0669 LRS0670 Rear facing step 3 Rear facing step 4 3 Pull the shoulder belt until the belt is fully 4 Allow the seat belt to retract Pull up on the extended At this time the seat belt retractor shoulder belt to remove any slack in the belt is in the Automatic Locking Retractor ALR mode child restraint mode It reverts to the Emergency Locking Retractor ELR mode when the seat belt is fully retracted 1 32 Safety Seats seat belts and supplemental restraint system WRS0762 Rear facing step 5 Remove any additional slack from the seat belt press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt WRS0763 Rear facing step 6 6 After attaching the child restraint test it be fore you place the child in it Push it from side to side while holding the child restraint near the seat belt path The child restraint should not move more than 1 inch 25 mm from side to side Try to tug it forward and check to see if the belt holds the restraint in place If the restraint is not secure tighten the seat belt as necessary or put the restraint in another seat and test it again You may need to try a different child
285. heater on and off The indicator light will remain on as long as the switch is on When the seat is warmed or before you leave the vehicle be sure to turn the switch off A WARNING Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat temperatures or have an inability to feel pain in body parts that contact the seat Use of the seat heater by such people could result in seri ous injury A CAUTION e Do not use the seat heater for extended periods or when no one is using the seat Do not put anything on the seat which insulates heat such as a blanket cush ion seat cover etc Otherwise the seat may become overheated e Do not place anything hard or heavy on the seat or pierce it with a pin or similar object This may result in damage to the heater Any liquid spilled on the heated seat should be removed immediately with a dry cloth e When cleaning the seat never use gasoline benzine thinner or any simi lar materials If any malfunctions are found or the heated seat does not operate turn the switch off and have the system checked by your NISSAN dealer The battery could run down if the seat heater is operated while the engine is not running Instruments and controls 2 35 CLIMATE CONTROL SEAT SWITCH if so equipped The climate controlled seat warms up or cools down the front seat by blowing warm or cool air from the surface o
286. hen available Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy genates such as ethanol MTBE and methanol with or without advertising their presence NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com patibility for your NISSAN cannot be readily de termined If in doubt ask your service station manager If you use oxygenate blend gasoline please take the following precautions as the usage of such fuels may cause vehicle performance problems and or fuel system damage The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline If an oxygenate blend other than methanol blend is used it should con tain no more than 10 oxygenate MTBE may however be added up to 15 E 15 fuel contains more than 10 oxy genate E 15 fuel will adversely affect the emission control devices and sys tems of the vehicle and should not be used Damage caused by such fuel is not covered by the NISSAN new vehicle limited warranty Technical and consumer information 9 3 e If a methanol blend is used it should contain no more than 5 methanol methyl alcohol wood alcohol It should also contain a suitable amount of appropriate cosolvents and corro sion inhibitors If not properly formu lated with appropriate cosolvents and corrosion inhibitors such methanol blends may cause fuel system damage and or ve
287. her brake fluid specification information refer to Capacities and recommended fuel lubricants in the Technical and consumer information section of this manual A WARNING Use only new fluid from a sealed con tainer Old inferior or contaminated fluid may damage the brake system The use of improper fluids can damage the brake system and affect the vehi cle s stopping ability Clean the filler cap before removing Brake fluid is poisonous and should be stored carefully in marked containers out of reach of children A CAUTION Do not spill the fluid on any painted sur faces This will damage the paint If fluid is spilled immediately wash the surface with water Maintenance and do it yourself 8 13 BRAKE FLUID Check the brake fluid level in the reservoir If the fluid level is below the MIN line or the brake warning light comes on add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line If fluid must be added frequently the system should be checked by a NISSAN dealer 8 14 Maintenance and do it yourself WINDSHIELD WASHER FLUID WINDSHIELD WASHER FLUID RESERVOIR Fill the windshield washer fluid reservoir periodi cally Add windshield washer fluid when the low windshield washer fluid warning light comes on To fill the windshield washer fluid reservoir lift the cap off the reservoir and pour the windshield washer fluid into the reservoir openin
288. hicle performance problems At this time sufficient data is not avail able to ensure that all methanol blends are suitable for use in NISSAN ve hicles If any driveability problems such as engine stall ing and difficult hot starting are experienced after using oxygenate blend fuels immediately change to a non oxygenate fuel or a fuel with a low blend of MTBE Take care not to spill gasoline during refu eling Gasoline containing oxygenates can cause paint damage E 15 fuel E 15 fuel is a mixture of approximately 15 fuel ethanol and 85 unleaded gasoline E 15 can only be used in vehicles designed to run on E 15 fuel Do not use E 15 in your vehicle U S gov ernment regulations require fuel ethanol dispens ing pumps to be identified with small square 9 4 Technical and consumer information orange and black label with the common abbre viation or the appropriate percentage for that region E 85 fuel E 85 fuel is a mixture of approximately 85 fuel ethanol and 15 unleaded gasoline E 85 can only be used in a Flexible Fuel Vehicle FFV Do not use E 85 in your vehicle U S government regulations require fuel ethanol dispensing pumps to be identified by a small square orange and black label with the common abbreviation or the appropriate percentage for that region Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives for example fuel injec tor cleaner octane booste
289. his could damage the CD and or CD changer player Trying to load a CD with the CD door closed could damage the CD and or CD changer e Only one CD can be loaded into the CD player at a time Only use high quality 4 7 in 12 cm round discs that have the COMPACT disc DIGITAL AUDIO logo on the disc or packaging During cold weather or rainy days the player may malfunction due to the hu midity If this occurs remove the CD and dehumidify or ventilate the player completely The player may skip while driving on rough roads The CD player sometimes cannot func tion when the compartment tempera ture is extremely high or low Decrease increase the temperature before use Do not expose the CD to direct sun light CDs that are in poor condition or are dirty scratched or covered with finger prints may not work properly The following CDs may not work prop erly e Copy control compact discs CCCD Recordable compact discs CD R Rewritable compact discs CD RW Do not use the following CDs as they may cause the CD player to malfunc tion 3 1 in 8 cm discs with an adapter e CDs that are not round e CDs with a paper label e CDs that are warped scratched or have abnormal edges This audio system can only play pre recorded CDs It has no capability to record or burn CDs If the CD cannot be played one of the following messages will be displayed CHECK DISC Confi
290. his is not a malfunction VEHICLE DYNAMIC CONTROL VDC OFF SWITCH OFF LIC1548 The vehicle should be driven with the Vehicle Dynamic Control VDC system on for most driv ing Conditions If the vehicle is stuck in mud or snow the VDC system reduces the engine output to reduce wheel spin The engine speed will be reduced even if the accelerator is depressed to the floor If maximum engine power is needed to free a stuck vehicle turn the VDC system off To turn off the VDC system push the VDC OFF switch The amp indicator will come on Push the VDC OFF switch again or restart the engine to turn on the system See Vehicle Dy namic Control VDC system in the Starting and driving section Instruments and controls 2 37 POWER OUTLET STORAGE A CAUTION The outlet and plug may be hot during or immediately after use Only certain power outlets are designed for use with a cigarette lighter unit Do not use any other power outlet for an accessory lighter See your NISSAN dealer for additional information Do not use with accessories that exceed a 12 volt 120W 10A power draw e Do not use double adapters or more than one electrical accessory e Use power outlets with the engine run ning to avoid discharging the vehicle battery MAP POCKETS Avoid using power outlets when the air conditioner headlights or rear window defroster is on The power outlets are powered only when the
291. hort distances In these cases the battery may need to be charged to maintain battery health Brake fluid level Make sure that the brake fluid level is between the MIN and MAX lines on the reservoir Engine coolant level Check the coolant level when the engine is cold Engine drive belts Make sure the drive belts are not frayed worn cracked or oily Engine oil level Check the level after parking the vehicle on a level surface with the engine off Wait more than 10 minutes for the oil to drain back into the oil pan Exhaust system Make sure there are no loose supports cracks or holes If the sound of the exhaust seems unusual or there is a smell of exhaust fumes immediately have the exhaust system inspected by a NISSAN dealer See the carbon monoxide warning in the Starting and driving section of this manual Fluid leaks Check under the vehicle for fuel oil water or other fluid leaks after the vehicle has been parked for a while Water dripping from the air conditioner after use is normal If you should notice any leaks or if gasoline fumes are evident check for the cause and have it corrected imme diately Power steering fluid level and lines Check the level when the fluid is cold with the engine off Check the lines for proper attachment leaks cracks etc Radiator and hoses Check the front of the radiator and clean off any dirt insects leaves etc that may have accumulated Make sure the hoses hav
292. hose who use a pacemaker should contact the electric medical equipment manu facturer for the possible influences be fore use If the light does not illuminate with the ignition switch in the ON position have the vehicle checked by a NISSAN dealer as soon as possible If the light illuminates while driving avoid sudden steering maneuvers or abrupt braking reduce vehicle speed pull off the road to a safe location and stop the vehicle as soon as possible Driving with under inflated tires may permanently damage the tires and in crease the likelihood of tire failure Se rious vehicle damage could occur and may lead to an accident and could result in serious personal injury Check the tire pressure for all four tires Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label located in the driver s door opening to turn the low tire pressure warning light OFF If the light still comes on while driving after adjusting the tire pressure a tire may be flat If you have a flat tire re place it with a spare tire as soon as possible When a spare tire is mounted or a wheel is replaced tire pressure will not be indicated the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute The light will remain on after 1 minute Contact your NISSAN dealer as soon as possible for tire replacement and or system resetting Replacing ti
293. i glare rearview mirror in the Pre driving checks and adjust ments section You can also calibrate the compass by driving your vehicle on your everyday route The com pass will be calibrated once it has tracked three complete circles COMPASS DISPLAY Push the button for about 1 second when the ignition switch is placed in the ON position to toggle the outside temperature and compass direction display on or off The display will indicate the direction that the vehicle is heading N North E East S South W West If the display reads C calibrate the compass by driving the vehicle in three complete circles at less than 5 MPH 8 km h Instruments and controls 2 7 2 8 Instruments and controls Zone variation change procedure The difference between magnetic north and geo graphical north is known as variance In some areas this difference can sometimes be great enough to cause false compass readings Follow these instructions to set the variance for your particular location if this happens 1 Press and hold the button for about 8 seconds The current zone number will appear in the display Release the button 2 Find your current location on the zone map Refer to the illustration t 3 Press the N button repeatedly to toggle through the zone numbers until the desired number appears in the display Once you have selected a zone number the display will show a compass direc
294. icle s operation and the outside temperature Low outside temperature can lower the temperature of the air inside the tire which can cause a lower tire inflation pressure This may cause the low tire pressure warning light to illumi nate If the warning light illuminates check the tire pressure for all four tires The Tire and Loading Information label also referred to as the vehicle placard or tire inflation pressure label is located in the driver s door opening For additional information see Low tire pressure warning light in the Instruments and controls section and Tire Pressure Monitoring System TPMS in the In case of emergency section AWARNING If the low tire pressure warning light illu minates while driving avoid sudden steering maneuvers or abrupt braking reduce vehicle speed pull off the road to a safe location and stop the vehicle as soon as possible Driving with under inflated tires may permanently damage the tires and increase the likelihood of tire failure Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury Check the tire pressure for all four tires Adjust the tire pressure to the recom mended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF If you have a flat tire replace it with a spare tire as soon as possible See Flat tire in the In ca
295. icted course lines are wider than the actual width and course Monitor climate audio phone and voice recognition systems 4 23 1 Visually check that the parking space is safe 3 Slowly back up the vehicle adjusting the before parking your vehicle steering wheel so that the predicted course lines enter the parking space 2 The rear view of the vehicle is displayed on the screen when the shift lever is moved to the R Reverse position 4 24 Monitor climate audio phone and voice recognition systems 4 Maneuver the steering wheel to make the vehicle width guide lines parallel to the parking space while referring to the pre dicted course lines 5 When the vehicle is parked in the space completely move the shift lever to the P Park position and apply the parking brake DIFFERENCE BETWEEN PREDICTED AND ACTUAL DISTANCES The distance guide line and the vehicle width guide line should be used as a reference only when the vehicle is on a level paved surface The distance viewed on the monitor is for reference only and may be different than the actual distance between the vehicle and displayed objects 2 ie Backing up on a steep uphill When backing up the vehicle up a hill the dis tance guide lines and the vehicle width guide lines are shown closer than the actual distance For example the display shows 8 ft 1 0 m to the place A but the actual 3 ft 1 0 m distance on the hill is th
296. id warning Gite oH sete oe oe amp hee hee oy 2 24 Passenger air bag and status light 1 52 Security indicator light 2 16 Spotlights See map light 2 53 TRO NGIE s e ram wh ew Be a a 2 54 Warning indicator lights and audible SINCE lon s ad Ros 4 ee EO we ed e d 2 10 Lights Map lights 2 ea 26 ow ek oe ew 2 53 Lock Child safety reardoorlock 3 6 Door looks 4445404 6 2h a oe 3 4 Glove box lock 2 42 Power door locks 4 a s o aaoo isama 3 5 Trunk lid lock opener lever 3 19 Loose fuel cap warning ssaa aaa 2 25 3 21 Low fuel warning light 2 13 2 24 Low tire pressure warning light 2 12 Low windshield washer fluid warning light 2 24 Luggage See vehicle loading information 9 12 10 4 M Maintenance General maintenance 8 2 Inside the vehicle 8 3 Maintenance precautions 8 5 Outside the vehicle 8 2 Seat belt maintenance 1 23 Under the hood and vehicle 8 4 Malfunction indicator light 2 15 MapliGghts s s s i sayana a ee A a e 2 53 Map pocket oaoa e 2 39 Meters and gauges 204 2 4 Instrument brightness control 2 34 Mirror Automatic anti glare inside mirror 3 26 Outside mirror control aoaaa aa 3 28 Outside mirrors aoaaa aaa 3 28 Vanity Mirror aoaaa e 3 26 MOOMOO cos e 48 a ood Be a ee Se 2 47 N NISSA
297. iet as possible Close the windows to eliminate the surrounding noises traffic noises vibration sounds etc which may prevent the system from recognizing the voice commands cor rectly When the climate control is in the AUTO mode the fan speed decreases automati cally for easy recognition Wait until a tone sounds before speaking a command Speak in a natural voice without pausing between words Giving voice commands 1 Press and release the amp on the steering wheel button located Voice Recognition a _ Prone s CSS w Navigation Practice Information 4 Help Alternate Command Mode ON To stop prompt and say command push the TALK switch 2 A list of commands appears on the screen and the system announces Please say a command After the tone sounds and the icon on the screen changes from to B speak a command Once a command is recognized the system will announce the recognized command and perform the requested action If the command is not recognized the sys tem repeats the announcement Repeat the command in a clear voice after the tone Monitor climate audio phone and voice recognition systems 4 131 Operating tips Say a command after the tone Voice com mands cannot be accepted when the icon iS If the command is not recognized the sys tem repeats the announcement Repeat the command in a clear voi
298. if so equipped start the engine and push the rear window defroster switch on The rear window defroster indicator light on the switch comes on Push the switch again to turn the defroster off The rear window defroster automatically turns off after approximately 15 minutes A CAUTION When cleaning the inner side of the rear window be careful not to scratch or dam age the rear window defroster O Uy REAR LIC1388 Type B NOTE The top few rows of wires on the rear win dow are not part of the rear window de froster system These wires make up the antenna for the audio system Instruments and controls 2 29 HEADLIGHT AND TURN SIGNAL SWITCH XENON HEADLIGHTS if so equipped AWARNING Z HIGH VOLTAGE e When xenon headlights are on they produce a high voltage To prevent an electric shock never attempt to modify or disassemble Always have your xe non headlights replaced at a NISSAN dealer Xenon headlights provide considerably more light than conventional head lights If they are not correctly aimed they might temporarily blind an oncom ing driver or the driver ahead of you and cause a serious accident If headlights are not aimed correctly immediately take your vehicle to a NISSAN dealer and have the headlights adjusted correctly When the xenon headlight is initially turned on its brightness or color varies slightly However the color and brightness will soon stabilize 2 30 Instruments and c
299. ight will flash for approximately 1 minute The light will remain on after 1 minute Contact your NISSAN dealer as soon as possible for tire replacement and or system resetting Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS Do not inject any tire liquid or aerosol tire sealant into the tires as this may cause a malfunction of the tire pressure sensors CHANGING A FLAT TIRE If you have a flat tire follow the instructions be low Stopping the vehicle 1 Safely move the vehicle off the road and away from traffic 2 Turn on the hazard warning flashers 3 Park ona level surface and apply the parking brake Move the shift lever to P Park 4 Turn off the engine 5 Raise the hood to warn other traffic and to signal professional road assistance person nel that you need assistance 6 Have all passengers get out of the vehicle and stand in a safe place away from traffic and clear of the vehicle In case of emergency 6 3 Make sure the parking brake is securely applied and the CVT is shifted into P AWARNING Park Never change tires when the vehicle is on a slope ice or slippery areas This is hazardous Never change tires if oncoming traffic is close to your vehicle Wait for profes sional road assistance 6 4 In case of emergency Blocking wheels Place suitable blocks at both the front and back of the whee
300. il it is completely dry Do not place the Intelligent Key for an extended period in an area where tem peratures exceed 140 F 60 C Do not attach the Intelligent Key with a key holder that contains a magnet Do not place the Intelligent Key near equipment that produces a magnetic field such as a TV audio equipment and personal computers Sy SPA1951 Mechanical key The Intelligent Key contains the mechanical key which can be used in case of a discharged bat tery To remove the mechanical key release the lock knob on the back of the Intelligent Key To install the mechanical key firmly insert it into the Intelligent Key until the lock knob returns to the lock position The mechanical key can be used for operation in the same way as an ordinary key A CAUTION Always carry the mechanical key installed in the Intelligent Key slot See Doors in this section and Storage in the Instruments and controls section of this manual Valet hand off When you have to leave a key with a valet give them the Intelligent Key itself and keep the me chanical key with you to protect your belongings To prevent the glove box and the trunk from being opened during valet hand off follow the proce dures below 1 Push the trunk cancel switch to the OFF position 2 Remove the mechanical key from the Intelli gent Key 3 Lock the glove box and the trunk pass through with the mechanical key
301. ine with a wheel s off Always refer to the proper illustrations for the 2 Place the jack directly under the jack up the ground It may cause the vehicle to correct placement and jack up points for your point as illustrated so the top of the jack move specific vehicle model and jack type contacts the vehicle at the jack up point Align the jack head between the two notches in the front or the rear as shown Also fit the groove of the jack head between the notches as shown Carefully read the caution label attached to the jack body and the following instruc tions 1 Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench Do not remove the wheel nuts until the tire is off the ground 3 To lift the vehicle securely hold the jack lever and rod with both hands Carefully raise the vehicle until the tire clears the ground Re move the wheel nuts and then remove the tire The jack should be used on firm and level ground 6 6 In case of emergency Installing the spare tire The spare tire is designed for emergency use See specific instructions under the heading Wheels and tires in the Mainte nance and do it yourself section of this manual 1 Clean any mud or dirt from the surface be tween the wheel and hub 2 Carefully put the spare tire on and tighten the wheel nuts finger tight 3 With the wheel nut wrench tighten wheel nuts alternately and evenly as illustrated u
302. information When you have finished speaking the phone number the system repeats it back and an nounces the available commands Say Dial The system acknowledges the command and makes the call phone model See the cellular phone Own 1 Press the Ce er s Manual for details You can also visit www nissanusa com bluetooth for instruc button on the steering ahel Ae wicana For additional command options see List of voice commands in this section Monitor climatepaudio phone and voice recognition systems 4 97 Receiving a call When you hear the ring tone press the 6 button on the steering wheel Once the call has ended press the button on the steering wheel NOTE If you do not wish to take the call when you hear the ring tone press the button on the steering wheel For additional command options see List of voice commands in this section LIST OF VOICE COMMANDS Main Menu Call Phonebook Recent Calls Connect Phone Help When you press and release the amp 4 button on the steering wheel you can choose from the commands on the Main Menu The following pages describe these commands and the com mands in each sub menu Remember to wait for the tone before speaking After the main menu you can say Help to hear the list of commands currently available any time the system is waiting for a response If you want to
303. ing Sway control devices may be used to help control these affects If you choose to use one contact a reputable trailer hitch supplier to make sure the sway control device will work with the vehicle hitch trailer and the trailer s brake sys tem Follow the instructions provided by the manufacturer for installing and using the sway control device Class hitch Class trailer hitch equipment receiver ball mount and hitch ball can be used to tow trailers of a maximum weight of 2 000 Ib 907 kg 9 20 Technical and consumer information You may add Class trailer hitch equipment that has a 2 000 Ib 907 kg maximum weight rating to the vehicle but your vehicle is only capable of towing the maximum trailer weights shown in the Towing Load Specification chart earlier in this section A CAUTION Do not use axle mounted hitches The hitch should not be attached to or affect the operation of the impact absorbing bumper e Do not modify the vehicle exhaust sys tem brake system etc to install a trailer hitch To reduce the possibility of additional damage if your vehicle is struck from the rear where practical remove the receiver when not in use After the hitch is removed seal the bolt holes to prevent exhaust fumes water or dust from entering the passenger compartment Regularly check that all trailer hitch mounting bolts are securely mounted Tire pressures When towing a trailer infla
304. inish the call ing wheel Monitor climate audio phone and voice recognition systems 4 115 PHONE SETTINGS To set up the Bluetooth Hands Free Phone Sys tem to your perferred settings press the SET TING button on the control panel and select the Phone key on the display Mentem Rest See Vehicle Phonebook in this section for adding editing and deleting contacts in the vehicle phonebook See Handset Phonebook in this section for adding editing and deleting contacts in the handset phonebook When this option is turned on an incoming call will be placed on hold automatically after several rings oo GH When this option is turned on a specific ringtone that is different than the cellular phone s will sound when receiving a call See Handset Phonebook in this section for information about automatically downloading the handset phonebook 4 116 Monitor climate audio phone and voice recognition systems BLUETOOTH SETTINGS To set up the Bluetooth Hands Free Phone Sys tem to your preferred settings press the SET TING button on the control panel and select the Bluetooth key on the display po Mento Rest Replaced Connected Phone Replace the phone currently connected to the system This option allows you to keep any voicetags that were recorded using the pre vious phone Monitor climate audio phone and voice recognition systems 4 117 CALL VOLUME Adjusting the incoming or outgoing call volume
305. iod of time you should turn the head light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery DAYTIME RUNNING LIGHT SYSTEM Canada only The headlights automatically illuminate at a re duced intensity when the engine is started with the parking brake released The daytime running lights operate with the headlight switch in the OFF position or in the PG position Turn the headlight switch to the 2 position for full illumination when driving at night If the parking brake is applied before the engine is started the daytime running lights do not illumi nate The daytime running lights illuminate when the parking brake is released The daytime run ning lights will remain on until the ignition switch is placed in the OFF position AWARNING When the daytime running light system is active tail lights on your vehicle are not on It is necessary at dusk to turn on your headlights Failure to do so could cause an accident injuring yourself and others INSTRUMENT BRIGHTNESS CONTROL The instrument cluster illuminates when the igni tion switch is in the ON position The instrument brightness control operates when the headlight control switch is in the AUTO PO or 2 Turn the control left or right to adjust the bright ness of the instrument panel lights when driving at night position The instrument brightness control will not adjust the brightness when the headlights
306. ion e Remove the Intelligent Key from the Intelligent Key port after the ignition switch is pushed to the LOCK position NISSAN VEHICLE IMMOBILIZER SYSTEM The NISSAN Vehicle Immobilizer system will not allow the engine to start without the use of the registered key If the engine fails to start using a registered key for example when interference is caused by another registered key an automated toll road device or automatic payment device on the key ring restart the engine using the following pro cedure 1 Leave the ignition switch in the ON position for approximately 5 seconds 2 Place the ignition switch in the OFF or LOCK position and wait approximately 10 seconds 3 Repeat steps 1 and 2 4 Restart the engine while holding the device which may have caused the interference separate from the registered key If the no start condition re occurs NISSAN rec ommends placing the registered key on a sepa rate key ring to avoid interference from other devices BEFORE STARTING THE ENGINE Make sure the area around the vehicle is clear Check fluid levels such as engine oil cool ant brake fluid and window washer fluid as frequently as possible or at least whenever you refuel Check that all windows and lights are clean Visually inspect tires for their appearance and condition Also check tires for proper inflation Lock all doors Position seat and adjust head restraints headrests Ad
307. ire is attached to the unit If there is difficulty locating the button reference the garage door opener s manual Press and release the learn or smart but ton Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release Repeat the oress hold release sequence up to 3 times to complete the training process HomeLink should now activate your rolling code equipped device If you have any questions or are having diffi culty programming your HomeLink but tons refer to the HomeLink web site at www homelink com or call 1 800 355 3915 PROGRAMMING HOMELINK FOR CANADIAN CUSTOMERS AND GATE OPENERS Canadian radio frequency laws require transmit ter signals to time out or quit after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during training Similar to this Canadian law some U S gate operators are designed to tim eout in the same manner If you live in Canada or you are having difficulties training a gate operator or garage door opener by using the Training procedures replace Programming HomeLink Step 2 with the fol lowing NOTE When programming a garage door opener etc unplug the device during the cycling process to prevent possible damage to the garage door opener components 1 See Programing HomeLink step 1 earlier in this sec
308. is being driven Doing so may distract the driver and may cause a collision and serious personal injury or death Monitor climate audio phone and voice recognition systems 4 71 A CAUTION Only operate the DVD while the vehicle engine is running Operating the DVD for extended periods of time with the engine OFF can discharge the vehicle battery e Do not allow the system to get wet Excessive moisture such as spilled liq uids may cause the system to malfunction While playing VIDEO CD media this DVD player does not guarantee com plete functionality of all VIDEO CD formats Playing a DVD DISC AUX button Park the vehicle in a safe location for the front seat occupants to operate the DVD drive while watching the images Press the DISC AUX button until the DVD mode is active on the display When a DVD is loaded it will be replayed auto matically 4 72 Monitor climate audio phone and voice recognition systems The operation screen will be turned on when the DISC AUX button is pressed while a DVD is playing The operation screen will turn off auto matically after a period of time To turn it on again press the DISC AUX button DVD operation keys When the DVD is playing without the operation screen being shown you may use the touch screen to select items from the displayed video You may also use the NISSAN controller to select an item from the displayed video When the op eration screen is being
309. is transferred to the vehicle it can be accessed by pressing the PHONE key on the instrument panel or the button on the steering wheel then selecting the Handset Phonebook key Whether the handset phonebook is transferred manually or automatically the process can take up to five minutes to complete depending on the size of the handset phonebook See the cellular phone s owner s manual for more details MAKING A CALL Press the button on the steering wheel or the Phone button on the control panel The Phone screen will appear on the display Select Call History Connect Phone one of the following options to make a call a Yul 8 00 Vehicle Phonebook Volume amp Ringtone Handset Phonebook Connected Phones Calls a phonebook entry saved to the vehicle LHA1322 Vehicle Phonebook Select the name from an entry stored in the vehicle phonebook Dialing commences immediately Call History Select the name from the incoming or outgoing call history Dialing commences immediately Handset Phonebook Select the name from an entry stored in the handset phonebook Dialing commences immediately Dial Number Input the phone number manually using the keypad on the screen It will be necessary to select OK when finished for dialing to commence For more information on using the touchscreen see How to use the touchscreen in this section Monitor climate audio phone and voice recognition systems 4 113 RECEIVING
310. ith which your vehicle is equipped READ FIRST THEN DRIVE SAFELY Before driving your vehicle please read this Owner s Manual carefully This will ensure famil larity with controls and maintenance require ments assisting you in the safe operation of your vehicle AWARNING IMPORTANT SAFETY INFORMATION RE MINDERS FOR SAFETY Follow these important driving rules to help ensure a safe and comfortable trip for you and your passengers e NEVER drive under the influence of al cohol or drugs e ALWAYS observe posted speed limits and never drive too fast for conditions ALWAYS give your full attention to driving and avoid using vehicle features or taking other actions that could distract you ALWAYS use your seat belts and appro priate child restraint systems Preteen children should be seated in the rear seat e ALWAYS provide information about the proper use of vehicle safety features to all occupants of the vehicle e ALWAYS review this Owner s Manual for important safety information MODIFICATION OF YOUR VEHICLE This vehicle should not be modified Modification could affect its performance safety or durability and may even violate governmental regulations In addition damage or per formance problems resulting from modi fications may not be covered under NISSAN warranties WHEN READING THE MANUAL This manual includes information for all features and equipment available on this model
311. ition Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position This Maintenance and do it yourself section gives instructions regarding only those items which are relatively easy for an owner to perform You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions and could affect warranty coverage If in doubt about any servicing have it done by a NISSAN dealer 8 6 Maintenance and do it yourself 1 Power steering fluid reservoir 2 Engine oil filler cap 3 Brake fluid reservoir 4 Air cleaner 5 Fuse block Fusible links 6 Battery 7 Fusible links 8 Engine oil dipstick 9 Radiator cap 10 Drive belt location 11 Engine coolant reservoir 12 Windshield washer fluid reservoir NOTE Side covers removed for clarity To remove the engine compartment covers un hook the clips located as illustrated To remove the engine cover pull the cover up ward first 2 and then toward the front of the vehicle 2 Maintenance and do it yourself 8 7 ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with a pre diluted mixture of 50 Genuine NISSAN Long Life Antifreeze Coolant blue and 50 water to provide year round anti freeze and coolant protection The antifreeze solution con tains rust and corrosion inhibitors Additional en gine c
312. ition should get fresh air promptly Front air bags along with the use of seat belts help to cushion the impact force on the face and chest of the front occupants They can help save lives and reduce serious injuries However an inflating front air bag may cause facial abrasions or other injuries Front air bags do not provide restraint to the lower body Even with NISSAN advanced air bags seat belts should be correctly worn and the driver and pas senger seated upright as far as practical away from the steering wheel or instrument panel The front air bags inflate quickly in order to help protect the front occupants Because of this the force of the front air bag inflating can increase the risk of injury if the occupant is too close to or is against the front air bag module during inflation The front air bags deflate quickly after a collision The front air bags operate only when the ignition switch is in the ON or START posi tion 1 50 Safety Seats seat belts and supplemental restraint system After placing the ignition switch in the ON position the supplemental air bag warning light illuminates The supplemental air bag warning light will turn off after about 7 sec onds if the system is operational Front passenger air bag and status light AWARNING The front passenger air bag is designed to automatically turn OFF under some condi tions Read this section carefully to learn how it operates Proper use of
313. ition switch in the LOCK posi tion WPD0359 Locking doors 2 Close all doors 3 Press the Key button on the Intelligent 4 The hazard warning lights flash twice and the horn beeps once 5 All doors will be locked A CAUTION After locking the doors using the Intelli gent Key be sure that the doors have been securely locked by operating the door handles Pre driving checks and adjustments 3 13 Unlocking doors WPD0360 1 Press the if Key button on the Intelligent 2 The hazard warning lights flash once 3 Pressthe button again within 60 sec onds to unlock all doors All doors will be locked automatically unless one of the following operations is performed within 1 minute after pressing the 4 button Opening any doors Pushing the ignition switch 3 14 Pre driving checks and adjustments The interior light illuminates for a period of time when a door is unlocked and the room light switch is in the DOOR position The light can be turned off without waiting by performing one of the following operations Placing the ignition switch in the ON posi tion Locking the doors with the remote controller Switching the room light switch to the OFF position Opening windows The Intelligent Key allows you to simultaneously open windows equipped with automatic opera tion To open the windows press the but ton on the Intelligent Key for longer than 3 seconds after al
314. just inside and outside mirrors Fasten seat belts and ask all passengers to do likewise Check the operation of warning lights when the ignition switch is pushed to the ON position See Warning indicator lights and audible reminders in the Instruments and controls section of this manual STARTING THE ENGINE 1 Apply the parking brake 2 Move the shift lever to P Park or N Neu tral P Park is recommended The starter is designed not to operate if the shift lever is in any of the driving positions Push the ignition switch to the ON position Depress the brake pedal and push the igni tion switch to start the engine To start the engine immediately push and release the ignition switch while depressing the brake pedal with the ignition switch in any position f the engine is very hard to start in ex tremely cold weather or when restarting depress the accelerator pedal a little ap proximately 1 3 to the floor and while holding crank the engine Release the accelerator pedal when the engine starts Ifthe engine is very hard to start because it is flooded depress the accelerator pedal all the way to the floor and hold it Push the ignition switch to the ON posi tion to start cranking the engine After 5 or 6 seconds stop cranking by pushing the ignition switch to LOCK After cranking the engine release the accelerator pedal Crank the engine with your foot off the accelerator pedal b
315. kers or comes on during normal driving pull off the road in a safe area stop the engine immediately and call a NISSAN dealer or other authorized repair shop The engine oil pressure warning light is not designed to indicate a low oil level Use the dipstick to check the oil level See Engine oil in the Maintenance and do it yourself section of this manual 2 12 Instruments and controls A CAUTION Running the engine with the engine oil pressure warning light on could cause se rious damage to the engine almost imme diately Such damage is not covered by warranty Turn off the engine as soon as it is safe to do so KOJ Low tire pressure warning light Your vehicle is equipped with a Tire Pressure Monitoring System TPMS that monitors the tire pressure of all tires except the spare The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly After the ignition switch is placed in the ON position this light illuminates for about 1 second and turns off Low tire pressure warning If the vehicle is being driven with low tire pressure the warning light will illuminate A CHECK TIRE PRESSURE warning also appears in the vehicle information display When the low tire pressure warning light illuminates you should stop and adjust the tire pressure of all 4 tires to the recom mended COLD tire pressure shown on the Tire and Loading Information label located
316. l See Low tire pressure warning light earlier in this section and Tire Pressure Monitoring System TPMS in the Starting and driving section Tire pressure warning This screen will show the actual pressure of each tire Any low tire pressure will be highlighted The screen does not indicate which pressure corre sponds with which tire The numbers do not automatically update after tire pressure is adjusted After the tire is inflated to the recommended pressure the vehicle must be driven at speeds above 16 MPH 25 km h to update the numbers Refer to Tire Pressure Monitoring System in the Starting and driving section Intelligent Key error After the ignition switch is pushed to the ON position this light comes on for about 2 seconds and then turns off The I Key System Error message warns of a malfunction with the Intelligent Key system If the light comes on while the engine is stopped it may be impossible to start the engine If the light comes on while the engine is running you can drive the vehicle However in these cases contact a NISSAN dealer for repair as soon as possible Instruments and controls 2 25 SECURITY SYSTEMS Your vehicle has two types of security systems Vehicle security system NISSAN Vehicle Immobilizer System VEHICLE SECURITY SYSTEM The vehicle security system provides visual and audible alarm signals if someone opens the doors or trunk lid when th
317. l diagonally opposite the flat tire 2 to prevent the vehicle from moving when it is jacked up AWARNING Be sure to block the wheel as the vehicle may move and result in personal injury Getting the spare tire and tools Open the trunk Remove the floor carpeting and spare tire cover Jack up point and placing jack ro FO ae OS F Remove the jack 1 and wheel nut wrench 2 Remove the spare tire Jacking up vehicle and removing the from the tool box on the right side of the trunk damaaed tire compartment 9 A WARNING Never get under the vehicle while it is supported only by the jack If it is nec essary to work under the vehicle sup port it with safety stands Use only the jack provided with your vehicle to lift the vehicle Do not use the jack provided with your vehicle on other vehicles The jack is designed for lifting only your vehicle during a tire change In case of emergency 6 5 Use the correct jack up points Never use any other part of the vehicle for jack support Never jack up the vehicle more than necessary Never use blocks on or under the jack Do not start or run the engine while vehicle is on the jack It may cause the vehicle to move This is especially true for vehicles with limited slip Raise the differentials by hand ats ERE Do not allow passengers to stay in the vehicle while it is on the jack e Never run the eng
318. l doors are unlocked The door windows will open while pressing the button on the Intelligent Key The door windows cannot be closed by using the Intelligent Key Releasing the trunk lid Press the lt button for longer than 0 5 sec onds to open the trunk lid The trunk release button will not operate when the ignition switch is in the ON position or when the trunk cancel switch is in the OFF position See Cancel switch in this section Using the panic alarm If you are near your vehicle and feel threatened you may activate the panic alarm to call attention by pressing and holding the 1 button on the Intelligent Key for longer than 0 5 seconds The panic alarm and headlights will stay on for a period of time The panic alarm stops when It has run for a period of time or Any button is pressed on the Intelligent Key The request switch on the driver or passen ger door has been pushed and the Intelligent Key is in range of the door handle cr ch Silencing the horn beep feature WPD0362 If desired the horn beep feature can be deacti vated using the Intelligent Key To deactivate Press and hold the and ri buttons for at least 2 seconds The hazard warning lights will flash 3 times to confirm that the horn beep feature has been deactivated To activate Press and hold the and 2 buttons for at least 2 seconds once more The hazard warning lights will flash once and the
319. l switch Push the volume control switch to increase or decrease the volume Bi A Menu control switch ENTER button While the display is showing a MAP STATUS or Audio screen tilt the Menu Control switch up ward or downward to select a station track CD or folder For most audio sources tilting the switch up down for more than 1 5 seconds pro vides a different function than a tilting up down for less than 1 5 seconds AM and FM Tilt up down for less than 1 5 seconds to increase or decrease the preset station Tilt up down for more than 1 5 seconds to seek up or down to the next station Press the ENTER button to show the list of preset stations XM if so equipped Tilt up down for less than 1 5 seconds to increase or decrease the preset station Tilt up down for more than 1 5 seconds to go to the next or previous category Press the ENTER button to show the XM Menu iPod if so equipped Tilt up down for less than 1 5 seconds to increase or decrease the track number Press the ENTER button to show the iPod Menu CD Tilt up down for less than 1 5 seconds to increase or decrease the track number 4 90 Monitor climate audio phone and voice recognition systems Tilt up down for more than 1 5 seconds to increase or decrease the folder number if playing compressed audio files Press the ENTER button to show the CD Menu DVD if so equipped Tilt up down f
320. l the in take air press the TS air recirculation button To return to the automatic control mode press and hold the V gt air recirculation button or press and hold the gt fresh air intake button for about 2 seconds The indicator lights both air recirculation and fresh air intake buttons will flash twice and then the intake air will be con trolled automatically Air flow control Pressing the MODE button manually controls air flow and selects the air outlet 4 Air flows from center and side vents 74 Air flows from center and side vents and foot outlets Air flows mainly from foot outlets Air flows from defroster and foot outlets To turn system off Press the OFF button OPERATING TIPS When the engine coolant temperature and outside air temperature are low the air flow from the foot outlets may not operate for a maximum of 150 seconds However this is not a malfunction After the coolant tempera ture warms up air flow from the foot outlets will operate normally The sunload sensor located on the top driver s side of the instrument panel helps the system maintain a constant temperature Do not put any thing on or around this sensor Monitor climate audio phone and voice recognition systems 4 31 HEATER AND AIR CONDITIONER automatic Type B Type B gt Air recirculation button 9 Temperature control dial driver s side A C air conditioner ON O
321. lack label with the common abbrevia tion or the appropriate percentage for that region For additional information see Capacities and recommended fuel lubricants in the Technical and consumer information section RECOMMENDED ENGINE OIL Genuine NISSAN engine oil or equivalent 3 Engine oil with API Certification Mark Viscosity SAE 5W 30 See Engine oil and oil filter recommendation in the Technical and consumer information sec tion of this manual COLD TIRE PRESSURE See Tire and Loading Information label The label is typically located on the driver side center pillar or on the driver s door For additional information see Wheels and tires in the Main tenance and do it yourself section of this manual RECOMMENDED NEW VEHICLE BREAK IN PROCEDURE During the first 1 200 mi 2 000 km of vehicle use follow the recommendations outlined in the Break in schedule information found in the Starting and driving section of this manual Fol low these recommendations for the future reli ability and economy of your new vehicle Failure to follow these recommendations may result in vehicle damage or shortened engine life Pining Joly 2013113 Publication No OM14E OA35UO0O Printed in U S A
322. lation cannot be activated when the air conditioner is in the Y front defrosting P mode or the front defrosting and foot out let mode Fresh air intake Press the fresh air intake button to draw outside air into the passenger compartment The indicator light on the button will come on Automatic intake air control In the AUTO mode the intake air will be con trolled automatically To manually control the in take air press the lt E air recirculation button To return to the automatic control mode press and hold the V gt air recirculation button or press and hold the gt fresh air intake button for about 2 seconds The indicator lights both air recirculation and fresh air intake buttons will flash twice and then the intake air will be con trolled automatically Air flow control Pressing the MODE button manually controls air flow and selects the air outlet 4 Air flows from center and side vents 74 Air flows from center and side vents and foot outlets Air flows mainly from foot outlets Air flows from defroster and foot outlets To turn system off Press the OFF button OPERATING TIPS When the engine coolant temperature and outside air temperature are low the air flow from the foot outlets may not operate for a maximum of 150 seconds However this is not a malfunction After the coolant tempera ture warms up air flow from the foot outlets will operate no
323. le appearance Polishing is recommended to remove built up wax residue and to avoid a weathered appearance before re applying wax A NISSAN dealer can assist you in choosing the proper product Wax your vehicle only after a thorough wash ing Follow the instructions supplied with the wax Do not use a wax containing any abrasives cutting compounds or cleaners that may damage the vehicle finish Machine compounding or aggressive polishing on a base coat clear coat paint finish may dull the finish or leave swirl marks REMOVING SPOTS Remove tar and oil spots industrial dust insects and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining Special cleaning products are available at a NISSAN dealer or any automotive accessory store UNDERBODY In areas where road salt is used in winter it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing the acceleration of corrosion on the un derbody and suspension Before the winter pe riod and again in the spring the underseal must be checked and if necessary retreated Ot x WAI0007 GLASS When cleaning the rear window it may be easier to clean if the high mounted stop light if so equipped is removed first Be careful when removing the high mounted stop light to reduce the risk of damaging the high mounted stop light wires To remove the high mounted stop
324. le handling characteristics affect the VDC system and or interference with the brake discs Such interference can lead to decreased braking efficiency and or early brake pad shoe wear Re fer to Wheels and tires in the Techni cal and consumer information section of this manual for wheel off set dimensions When a spare tire is mounted or a wheel is replaced tire pressure will not be indicated the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute The light will remain on after 1 minute Contact your NISSAN dealer as soon as possible for tire replacement and or system resetting Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS Do not install a damaged or deformed wheel or tire even if it has been re paired Such wheels or tires could have structural damage and could fail with out warning e The use of retread tires is not recommended For additional information regarding tires refer to Important Tire Safety In formation US or Tire Safety Informa tion Canada in the Warranty Informa tion Booklet Wheel balance Unbalanced wheels may affect vehicle handling and tire life Even with regular use wheels can get out of balance Therefore they should be bal anced as required Wheel balance service should be per formed with the wheels off the vehicle Spin balancing th
325. light Push toward rear of vehicle 2 Lift to remove The high mounted stop light must be properly reinstalled before driving your vehicle Use glass cleaner to remove smoke and dust film from the glass surfaces It is normal for glass to become coated with a film after the vehicle is parked in the hot sun Glass cleaner and a soft cloth will easily remove this film A CAUTION When cleaning the inside of the windows do not use sharp edged tools abrasive cleaners or chlorine based disinfectant cleaners They could damage the electrical conductors radio antenna elements or rear window defroster elements ALUMINUM ALLOY WHEELS Wash the wheels regularly with a sponge damp ened in a mild soap solution especially during winter months in areas where road salt is used If not removed road salt can discolor the wheels A CAUTION Follow the directions below to avoid staining or discoloring the wheels e Do not use a cleaner that uses strong acid or alkali contents to clean the wheels Appearance and care 7 3 e Do not apply wheel cleaners to the wheels when they are hot The wheel temperature should be the same as am bient temperature Rinse the wheel to completely remove the cleaner within 15 minutes after the cleaner is applied CHROME PARTS Clean all chrome parts regularly with a non abrasive chrome polish to maintain the finish TIRE DRESSINGS NISSAN does not recommend the use of tire dressings
326. lights will illuminate under the following conditions Do not allow children near the rear sun shade system They could be injured Do not pull or push the rear sun shade This could cause improper operation or damage it Driver s door is unlocked while the igni tion switch is placed in the OFF position Lights remain on for a period of time 2 50 Instruments and controls NOTE The footwell and doorstep lights illuminate when the driver and passenger doors are opened regardless of the interior light switch position These lights will turn off automatically after a period of time while doors are open to prevent the battery from becoming discharged A CAUTION Do not use for extended periods of time with the engine stopped This could result in a discharged battery CONSOLE LIGHT The console light will turn on whenever the park ing lights or headlights are illuminated The console light brightness can be adjusted with the illumination brightness control PERSONAL LIGHTS LIC1413 To turn on the personal lights press and release the switch 1 To turn the personal lights off press and release the switch 1 Instruments and controls 2 51 ON DOOR OFF Lil it WIC1494 WIC1494 LIC1409 Models without moonroof Models with moonroof Models with dual panel moonroof 2 52 Instruments and controls MAP LIGHTS To turn the map lights on press the switches To turn them off press the swit
327. ller Do not adjust the Brightness Tint Color Con trast and Black Level of the RearView Monitor while the vehicle is moving Make sure the park ing brake is firmly applied OPERATING TIPS A CAUTION Do not use alcohol benzine or thinner to clean the camera This will cause discoloration To clean the camera wipe with a cloth dampened with di luted mild cleaning agent and then wipe with a dry cloth e Do not damage the camera as the moni tor screen may be adversely affected When the shift lever is shifted to the R Re verse position the display screen automati cally changes to the RearView Monitor mode However the radio can be heard It may take some time until the RearView Monitor or the normal screen is displayed after the shift lever has been shifted to R Reverse from another position or to an other position from R Reverse Objects may be distorted momentarily until the Rear View Monitor screen is displayed com pletely When the temperature is extremely high or low the screen may not clearly display ob jects This is not a malfunction When strong light directly enters the cam era objects may not be displayed clearly This is not a malfunction Vertical lines may be seen in objects on the screen This is due to strong reflected light from the bumper This is not a malfunction The screen may flicker under fluorescent light This is not a malfunction The colors of objects on the RearVi
328. lternate Command Mode Allows user to activate Alternate Command Mode A screen will appear prompting user to review the expanded command list and advises that some command will be replaced and voice menu prompts turned off User will have to confirm by pressing OK to proceed with activation 4 120 Monitor climate audio phone and voice recognition systems USING THE SYSTEM Initialization When the ignition switch is placed in the ON position NISSAN Voice Recognition is initialized which takes a few seconds When completed the system is ready to accept voice commands If the amp switch is pressed before the initializa tion completes voice commands will not be ac cepted Please wait until the NISSAN Voice Rec ognition initialization is completed BEFORE STARTING To get the best recognition performance from Voice Recognition observe the following The interior of the vehicle should be as quiet as possible Close the windows to eliminate the surrounding noises traffic noise and vi bration sounds etc which may prevent the system from correctly recognizing the voice commands Wait until the tone sounds before speaking a command Speak ina natural conversational voice with out pausing between words lf the air conditioner is set to Auto the fan speed is automatically lowered so that your commands can be recognized more easily GIVING VOICE COMMANDS 1 Pressthe amp ing wheel switch
329. ly flammable and highly explosive under certain condi tions You could be burned or seriously injured if it is misused or mishandled Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically Continued refueling may cause fuel overflow resulting in fuel spray and possibly a fire Use only an original equipment type fuel filler cap as a replacement It has a built in safety valve needed for proper operation of the fuel system and emis sion control system An incorrect cap can result in a serious malfunction and possible injury It could also cause the FNGINE Malfunction Indicator Light SOON MIL to come on Never pour fuel into the throttle body to attempt to start your vehicle Do not fill a portable fuel container in the vehicle or trailer Static electricity can cause an explosion of flammable liquid vapor or gas in any vehicle or trailer To reduce the risk of serious injury or death when filling portable fuel containers Always place the container on the ground when filling Do not use electronic devices when filling Keep the pump nozzle in contact with the container while you are fill ing it Use only approved portable fuel con tainers for flammable liquid A CAUTION e Do not use E 15 or E 85 fuel in your vehicle For further informatio
330. ly may further decrease recognition performance Example 2 Placing an international call to the phone number 011 81 111 222 3333 1 Pressthe v ing wheel button located on the steer 2 The system announces Would you like to access Phone Navigation Information Au dio or Help Say Phone Say International Call Say 011811112223333 Say Dial O O A O 4 126 Monitor climate audio phone and voice recognition systems 7 The system makes a call to 011 81 111 222 3333 NOTE Any digit input format is available in the International Number input process as well as the special characters such as star pound and plus NISSAN VOICE RECOGNITION ALTERNATE COMMAND MODE The Alternate Command Mode enables control of the audio and display systems as well as addi tional commands for the Vehicle Information Phone and Navigation systems With this setting active the system does not announce or display the available commands at each step When Alternate Command Mode is activated an expanded list of commands can be used after pushing the TALK switch Under this mode the screen for Standard Mode commands is not available on the display Please review the expanded command list available when this mode is active as some Standard Mode com mands are replaced Please see examples of Alternate Command Mode screens Please note that in this mode t
331. m weight load limit specified for the front or rear axle This informa tion Is located on the F M V S S C M V S S certification label GCWR Gross Combined Weight rating The maximum total weight rating of the vehicle passengers cargo and trailer Vehicle Capacity Weight Load limit Total load capacity maximum total weight limit specified of the load passengers and cargo for the ve hicle This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle If the vehicle is used to tow a trailer the trailer tongue weight must be in cluded as part of the cargo load This information is located on the Tire and Loading Information label Cargo capacity permissible weight of cargo the subtracted weight of occupants from the load limit VEHICLE LOAD CAPACITY Do not exceed the load limit of your ve hicle shown as The combined weight of occupants and cargo on the Tire and Loading Information label Do not exceed the number of occupants shown as Seating Capacity on the Tire and Load ing Information label To get the combined weight of occu pants and cargo add the weight of all occupants then add the total luggage weight Examples are shown in the follow ing illustration Technical and consumer information 9 13 Load limit 1 400 Ib 640 kg Load limit 1 400 Ib 640 kg Load limit 1 400 Ib 640 kg Luggage Trailer Tongue Weight 300 Ib
332. matic Type B 4 32 Automatic operation 0 cece ee eee 4 33 Manual operation enn cece naaraana nane 4 34 Operating 10S risser pntin in venues Ar ARE 4 34 Servicing air CONGHIONE ci ckavens uutdewersedwnwds 4 35 AUdIO SYSTEMI cres s ce nuu sae Siar aeevasenceceserses 4 35 ROCIO 626 302 555260800005 bG5e6 A 4 35 FM radio reception 2ccccccncckdedurceaseicdse es 4 35 AM radio reception sssssssnnnnanrrrrrrnnu 4 36 Satellite radio reception if so equipped 4 36 Audio operation precautions 0000e 4 36 FM AM radio with compact disc CD changer if so equipped 6 cece eee ees 4 51 FM AM SAT radio with compact disc CD player if so equipped 0 0 c cece eee eee 4 56 FM AM SAT radio with CD DVD player if so equipped lt ccc cax teed eauethcaveeeeedonds 4 63 Digital Versatile Disc DVD Player Operation models with Navigation System 4 71 USB interface models without Navigation System if so equipped cece eee ees 4 74 USB interface models with Navigation SE jo pied cna weap E es 4 76 iPod player operation without Navigation System if so equipped n nana cece eens 4 80 iPod player operation with Navigation System if so equipped n 0 cece eee ees 4 82 Bluetooth streaming audio if so equipped 4 85 CD care and Cleaning 4 s 3c0iceusevenegaveek ves 4 88 Steering wheel switch for audio control 4 89 POCO E af 0
333. me duration etc ID3 tag information is displayed on the Album Artist Track title line on the display Windows Windows Media and Windows Vista are registered trademarks or trademarks of Microsoft Corporation in the United States of America and or other countries Monitor climate audio phone and voice recognition systems 4 45 Playback order Music playback order of a CD DVD or USB device with compressed audio files is as illus trated The folder names of folders not containing compressed audio files are not shown in the display f there is a file in the top level of the disc USB Root Folder is displayed The playback order is the order in which the files were written by the writing software so the files might not play in the desired order FOLDER COMPRESSED AUDIO FILES WHA1374 Playback order chart 4 46 Monitor climate audio phone and voice recognition systems Specification chart Supported media CD CD R CD RW DVD ROM DVD R DVD RW DVD R DL USB 2 0 CD CD R CD RW DVD ROM DVD R DVD RW DVD R DL ISO9660 LEVEL1 ISO9660 LEVEL2 Romeo Joliet ISO9660 Level 3 packet writing is not supported Files saved using the Live File System component on a Windows Vista operating system based computer are not supported UDF Bridge UDF 1 02 ISO9660 UDF 1 5 UDF 2 0 VDF 1 5 VDF 2 0 packet writing is not supported USB memory FAT16 FAT32 MPEG1 MPEG2 MPEG2 5
334. ments on your vehicle in a reliable and economical way GENERAL MAINTENANCE During the normal day to day operation of the vehicle general maintenance should be per formed regularly as prescribed in this section If you detect any unusual sounds vibrations or smells be sure to check for the cause or have a NISSAN dealer do it promptly In addition you should notify a NISSAN dealer if you think that repairs are required When performing any checks or maintenance work closely observe the Maintenance precau tions later in this section EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with is found later in this section Outside the vehicle The maintenance items listed here should be performed from time to time unless otherwise specified Doors and engine hood Check that the doors and engine hood operate properly Also ensure that all latches lock securely Lubricate hinges latches latch pins rollers and links as necessary Make sure that the secondary latch keeps the hood from opening when the primary latch is released When driving in areas using road salt or other corrosive materials check lubrication frequently Lights Clean the headlights on a regular basis Make sure that the headlights stop lights tail lights turn signal lights and other lights are all operating properly and installed securely Also check headlight aim Road wheel nuts lug nu
335. meter 1 records the total distance the vehicle has been driven The twin trip odometer records the distance of individual trips 2 4 Instruments and controls awt fuy QS il SS os TACHOMETER The tachometer indicates engine speed in revo lutions per minute RPM Do not rev the engine into the red zone 1 A CAUTION When engine speed approaches the red zone shift to a higher gear or reduce en gine speed Operating the engine in the red zone may cause serious engine damage ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tempera ture The engine coolant temperature is within the normal range 4 when the gauge needle points within the zone shown in the illustration The engine coolant temperature varies with the outside air temperature and driving conditions A CAUTION If the gauge indicates coolant tempera ture near the hot H end of the normal range reduce vehicle speed to decrease temperature If the gauge is over the nor mal range stop the vehicle as soon as safely possible If the engine is over heated continued operation of the vehicle may seriously damage the engine See If your vehicle overheats in the In case of emergency section for immediate action required Instruments and controls 2 5 FUEL GAUGE The gauge indicates the approximate fuel level in the tank The gauge may move slightly during braking turning acceleration or going up
336. mmable materials such as dry grass waste paper or rags They may ignite and cause a fire Safe parking procedures require that both the parking brake be set and the transmission placed into P Park Fail ure to do so could cause the vehicle to move unexpectedly or roll away and re sult in an accident Make sure the shift lever has been pushed as far forward as it can go and cannot be moved without depressing the foot brake pedal Never leave the engine running while the vehicle is unattended Do not leave children unattended inside the vehicle They could unknowingly ac tivate switches or controls Unattended children could become involved in seri ous accidents Firmly apply the parking brake 2 Move the shift lever to the P Park position To help prevent the vehicle from rolling into traffic when parked on an incline It is a good practice to turn the wheels as illustrated HEADED DOWNHILL WITH CURB Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb HEADED UPHILL WITH CURB Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb HEADED UPHILL OR DOWNHILL NO CURB Turn the wheels toward the side of the road so the vehicle will move away from the cen ter of the road if it moves Place the ignition switch to the LOCK posi tion Starting and driving 5 23 POWER STEERING
337. modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment For Canada This device complies with RSS 210 of In dustry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference in cluding interference that may cause unde sired operation of the device LIGHTS HEADLIGHTS Replacing the xenon headlight bulb if so equipped AWARNING Z HIGH VOLTAGE When xenon headlights are on they pro duce a high voltage To prevent an electric shock never attempt to modify or disas semble Always have your xenon head lights replaced at a NISSAN dealer For additional information see Headlight and turn signal switch in the Instru ments and controls section Replacing the halogen headlight bulb if so equipped The headlight is a semi sealed beam type which uses a replaceable headlight halogen bulb Be cause the headlight assembly must be removed from the vehicle for bulb replacement see your NISSAN dealer A CAUTION Aiming is not necessary after replacing the bulb When aiming adjustment is necessary contact a NISSAN dealer Do not leave the headlight assembly open without a bulb installed for a long period of time Dust moisture smoke etc entering the headlight body may affect bulb performance Remove the bulb from the headli
338. mple the Intelligent Key battery is dis charged If this indicator illuminates insert the Intelligent Key into the Intelligent Key port in the correct direction See Push button ignition switch in the Starting and driving section NISSAN Intelligent Key removal indica tor This indicator illuminates when the driver s door is opened with the ignition switch placed in the OFF position and the Intelligent Key placed in the Intelligent Key port A key reminder chime also sounds If this indicator illuminates remove the Intelligent Key from the Intelligent Key port and take it with you when leaving the vehicle NISSAN Intelligent Key battery dis charge indicator This indicator illuminates when the Intelligent Key battery is running out of power If this indicator illuminates replace the battery with a new one See Battery replacement in the Maintenance and do it yourself section Loose fuel cap warning This warning appears when the fuel filler cap is not tightened correctly after the vehicle has been refueled See Fuel filler cap in the Pre driving checks and adjustments section Check tire pressure warning This warning appears when the low tire pressure warning light in the meter illuminates and low tire pressure is detected If this warning appears stop the vehicle and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information labe
339. mum clearances between the tire and the closest vehicle suspension or body component required to accommodate the 8 40 Maintenance and do it yourself use of a winter traction device tire chains or cables The minimum clearances are determined using the factory equipped tires Other types may damage your vehicle Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit Loose end links of the tire chain must be secured or removed to prevent the pos sibility of whipping action damage to the fenders or underbody If possible avoid fully loading your vehicle when using tire chains In addition drive at a reduced speed Otherwise your vehicle may be damaged and or vehicle handling and perfor mance may be adversely affected Tire chains must be installed only on the front wheels and not on the rear wheels Never install tire chains on a TEMPORARY USE ONLY spare tire Do not use tire chains on dry roads Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress WD10258 CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7 500 miles 12 000 km See Flat tire in the In case of emer gency section of this manual for tire re placing procedures As soon as possible tighten the wheel nuts to the specified torque with a torque wrench Wheel nut tightening torque 83 ft lb 112 N m
340. n will return to the D Drive mode Tocancel the M Manual mode and return to the D Drive mode press and hold either shift paddle for 3 5 seconds Follow these procedures for maximum vehicle performance and driving enjoyment NOTE Engine power may be automatically re duced to protect the CVT if the engine speed increases quickly when driving on slippery roads or while being tested on some dynamometers Starting the vehicle 1 After starting the engine fully depress the foot brake pedal before moving the shift lever out of the P Park position 2 Keep the foot brake pedal depressed and move the shift lever into a driving gear 3 Release the foot brake then gradually start the vehicle in motion Starting and driving 5 13 4 Stop the vehicle completely before shifting the shift lever to the P Park position The CVT is designed so the foot brake pedal MUST be depressed before shifting from P Park to any drive position while the ignition switch is in the ON position The shift lever cannot be moved out of P Park and into any of the other gear posi tions if the ignition switch is pushed to the LOCK position 5 14 Starting and driving To move the shift lever Press the button while depressing the m brake pedal Press the button to shift cS Shift without pressing button Shifting After starting the engine fully depress the brake pedal and move the shift lever from P Park to any
341. n Constant Speed Look ahead to try and anticipate and mini mize stops Synchronizing your speed with traffic lights allows you to reduce your number of stops Maintaining a steady speed can minimize red light stops and improve fuel efficiency 3 Use Air Conditioning A C at Higher Vehicle Speeds Below 40 MPH 64 km h it is more efficient to open windows to cool the vehicle due to reduced engine load Above 40 MPH 64 km h it is more efficient to use A C to cool the vehicle due to increased aerodynamic drag Recirculating the cool air in the cabin when the A C is on reduces cooling load Drive at Economical Speeds and Dis tances Observing the speed limit and not ex ceeding 60 MPH 97 km h where le gally allowed can improve fuel efficiency due to reduced aerodynamic drag Maintaining a safe following distance be hind other vehicles reduces unnecessary braking Safely monitoring traffic to anticipate changes in speed permits reduced brak ing and smooth acceleration changes Select a gear range suitable to road con ditions Use Cruise Control Using cruise control during highway driv ing helps maintain a steady speed Cruise control is particularly effective in providing fuel savings when driving on flat terrains Starting and driving 5 21 Plan for the Shortest Route Utilize a map or navigation system to de termine the best route to save time Avoid Idling
342. n last played The last station played will also come on when the VOL ON OFF control knob is pressed ON When the SAT button is pressed the satellite radio reception will not be available unless an optional satellite receiver and antenna are in stalled and a SiriusXM Satellite Radio service subscription is active Satellite radio is not avail able in Alaska Hawaii and Guam If a compact disc is playing when the SAT button is pressed the compact disc will automatically be turned off and the last radio station played will come on TUNE FOLDER Tuning knob To manually tune the radio turn the TUNE FOLDER knob to the right or left 44 pp SEEK CAT and TRACK tuning buttons For AM or FM Press the SEEK CAT 44 button or the TRACK PI button to tune from high to low or low to high frequencies and stop at the next broadcasting station For XM Press the SEEK CAT M4 button or the TRACK PI button to go to the first channel of the previous or next category SCAN tuning Press the SCAN button to stop at each broad casting station for 5 seconds Pressing the SCAN button again during this five second pe riod will stop scan tuning and the radio will remain tuned to that station If the SCAN button is not pressed within 5 seconds scan tuning moves to the next station 4 66 Monitor climate audio phone and voice recognition systems 1 to 6 Station memory operations Six stations can be set for the AM band T
343. n see the Fuel Recommendation in the Techni cal and consumer information section of this manual The LOOSE FUEL CAP warning will ap pear if the fuel filler cap is not properly tightened It may take a few driving trips for the message to be displayed Failure to tighten the fuel filler cap properly after the LOOSE FUEL CAP warning ap pears may cause the UIGE Malfunc h SOON tion Indicator Light MIL to illuminate Failure to tighten the fuel filler cap SERVICE properly may cause the ENGINE Mal function Indicator Light MID to illumi nate If the ONE light illuminates be cause the fuel filler cap is loose or missing tighten or install the cap and continue to drive the vehicle SERVICE The ENGINE light should turn off after a few driving trips If the THONE light N does not turn off after a few driving trips have the vehicle inspected by a NISSAN dealer For additional information see the Malfunction Indicator Light MIL in the Instruments and Controls section in this manual If fuel is spilled on the vehicle body flush it away with water to avoid paint damage To remove the fuel filler cap i Turn the fuel filler cap counterclockwise to remove Put the fuel filler cap on the cap holder while refueling To install the fuel filler cap 1 Insert the fuel filler cap straight into the fuel filler tube 2 Turn the fuel filler cap clockwise
344. n snowy or icy roads NISSAN recom mends the use of MUD amp SNOW or ALL SEASON TIRES on all four wheels Please consult a NISSAN dealer for the tire type size speed rating and availability informa tion 2 For additional traction on icy roads studded tires may be used However some U S states and Canadian provinces prohibit their use Check local state and provincial laws before installing studded tires Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non studded snow tires 3 Tire chains may be used For details see Tire chains in the Maintenance and do it yourself section of this manual SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter e A scraper and stiff bristled brush to remove ice and snow from the windows and wiper blades e A sturdy flat board to be placed under the jack to give it firm support Ashovel to dig the vehicle out of snowdrifts Extra washer fluid to refill the windshield washer fluid reservoir DRIVING ON SNOW OR ICE AWARNING e Wet ice 32 F 0 C and freezing rain very cold snow or ice can be slick and very hard to drive on The vehicle will have much less traction or grip under these conditions Try to avoid driving on wet ice until the road is salted or sanded Whatever the condition drive with cau tion Accelerate and slow down with
345. n the front passenger seat place the ignition switch in the ON position The front passenger air bag status light 2 may or may not illuminate depending on the size of the child and the type of booster seat being used See Front passenger air bag and status light later in this section 1 42 SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System SRS sec tion contains important information concerning the following systems Driver and passenger supplemental front impact air bag NISSAN Advanced Air Bag System Front seat mounted side impact supple mental air bag Roof mounted curtain side impact supple mental air bag Seat belt with pretensioner Supplemental front impact air bag system The NISSAN Advanced Air Bag System can help cushion the impact force to the head and chest of the driver and front passenger in certain frontal collisions Front seat mounted side impact supple mental air bag system This system can help cushion the impact force to the chest and pelvic area of the driver and front passenger in certain side impact collisions The side air bags are de signed to inflate on the side where the vehicle is impacted Safety Seats seat belts and supplemental restraint system Roof mounted curtain side impact supple mental air bag system This system can help cushion the impact force to the head of occu pants in front and rear o
346. n the passenger compartment fuse box Type A fuses can be installed in the engine com partment and passenger compartment fuse boxes 8 22 Maintenance and do it yourself DEREI a o all f If a type A fuse is used to replace a type B fuse the type A fuse will not be level with the fuse pocket as shown in the illustration This will not affect the performance of the fuse Make sure the fuse is installed in the fuse box securely Type B fuses cannot be installed in the under hood fuse boxes Only use type A fuses in the underhood fuse boxes ENGINE COMPARTMENT A CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover This could damage the electrical system or cause a fire If any electrical equipment does not come on check for an open fuse 1 Be sure the ignition switch and the headlight switch are OFF 2 Open the engine hood Remove the fuse box cover by pushing the tab and lifting the cover up Remove the fuse with the fuse puller The fuse puller is located in the center of the fuse block in the passenger compartment 5 If the fuse is open replace it with a new fuse 6 6 If a new fuse also opens have the electrical system checked and repaired by a NISSAN dealer Maintenance and do it yourself 8 23 Fusible links If the electrical equipment does not operate and fuses are in good condition check the
347. ndard Mode 4 119 Using the SYStCMiscdscn duseeduteeeehesneewen du Before starting eu mudsciocecosecouereteceueeses 4 121 Giving Voice COMMANAS v 02 c02e0 se casew sew eaws 4 121 NISSAN Voice Recognition Alternate 4 126 Command Mode 2eececceeeeeeeeaes Using the system Speaker Adaptation function 000ee Troubleshooting guide CONTROL PANEL BUTTONS COLOR SCREEN WITHOUT NAVIGATION SYSTEM if so equipped AWARNING Positioning of the heating or air condi tioning controls and display controls should not be done while driving in or der that full attention may be given to the driving operation Do not disassemble or modify this sys tem If you do it may result in accidents fire or electrical shock e Do not use this system if you notice any abnormality such as a frozen screen or lack of sound Continued use of the system may result in accident fire or electric shock In case you notice any foreign object in the system hardware spill liquid on it or notice smoke or smell coming from it stop using the system immediately and contact your nearest NISSAN dealer Ig noring such conditions may lead to ac cidents fire or electrical shock h STATUS button P 4 6 5 BRIGHT brightness control button 2 INFO button P 4 6 6 BRIGHT brightness control button 3 NISSAN controller P 4 5 7 BACK previous button P 4 5 4 8 amp 2_ OFF b
348. ndling of your vehicle Generally snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed Never ex ceed the maximum speed rating of the tire If you install snow tires they must be the same size brand construction and tread pattern on all four wheels Maintenance and do it yourself 8 39 For additional traction on icy roads studded tires may be used However some U S states and Canadian provinces prohibit their use Check local state and provincial laws before installing studded tires Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non studded snow tires TIRE CHAINS A CAUTION Tire chains cables should not be installed on P245 40VR19 size tires Installation of the tire chains cables on P245 40VR19 size tires will cause damage to the vehicle If you plan to use tire chains cables you should install P245 45VR18 size tires on your vehicle Use of tire chains may be prohibited according to location Check the local laws before installing tire chains When installing tire chains make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer s suggestions Use only SAE class S chains Class S chains are used on vehicles with restricted tire to vehicle clearance Vehicles that can use Class S chains are de signed to meet the mini
349. ne NISSAN CVT Fluid NS 2 will damage the CVT which is not covered by the NISSAN new vehicle limited warranty Available in mainland U S A through a NISSAN dealer For further details see Air conditioner system refrigerant and oil recommendations in this section For further details see Engine Oil in the Maintenance and do it yourself section of this manual DEXRON VI type ATF may also be used 2 Technical and consumer information Recommended Fluids and Lubricants Unleaded gasoline with an octane rating of at least 91 AKI RON 96 1 Genuine NISSAN engine oil or equivalent 3 Engine oil with API Certification Mark 2 Viscosity SAE 5W 30 Pre diluted Genuine NISSAN Long Life Antifreeze Coolant blue or equivalent Genuine NISSAN CVT Fluid NS 2 4 Genuine NISSAN PSF or equivalent 8 Genuine NISSAN Super Heavy Duty Brake Fluid 5 or equivalent DOT 3 NLGI No 2 Lithium Soap base HFC 134a R 134a 6 Genuine NISSAN A C System Oil Type DH PS or equivalent 6 Genuine NISSAN Windshield Washer Concentrate Cleaner amp Antifreeze or equivalent FUEL RECOMMENDATION NISSAN recommends the use of unleaded pre mium gasoline with an octane rating of at least 91 AKI Anti Knock Index number Research octane number 96 If unleaded premium gaso line is not available you may use unleaded regular gasoline with an octane rating of at least 87 AKI number Research octane number 91 but you may notice a de
350. ng system TPMS that illuminates a low tire pressure telltale when one or more of your tires is significantly under inflated Accordingly when the low tire pressure telltale illuminates you should stop and check your tires as soon as possible and inflate them to the proper pressure Driving on a signifi cantly under inflated tire causes the tire to over heat and can lead to tire failure Under inflation also reduces fuel efficiency and tire tread life and may affect the vehicle s handling and stopping ability Please note that the TPMS is not a substitute for proper tire maintenance and it is the driver s responsibility to maintain correct tire pressure even if under inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly The TPMS mal function indicator is combined with the low tire pressure telltale When the system detects a malfunction the telltale will flash for approxi mately one minute and then remain continuously illuminated This sequence will continue upon subsequent vehicle start ups as long as the mal function exists When the malfunction indicator is illuminated the system may not be able to detect or signal low tire pressure as intended TPMS malfunctions may occur for a variety of reasons including the installation of replacement or alter nate
351. ng the key to neutral 3 where the key can only be removed and inserted and turning it toward the rear again within 60 seconds unlocks all doors Opening and closing windows The driver s door key operation allows you to open and close windows equipped with auto matic operation at the same time To open the windows turn the driver s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked To close the windows turn the driver s door key toward the front of the vehicle for longer than 1 second after the door is locked Windows stop when the key cylinder is released WPD0291 Inside lock LOCKING WITH INSIDE LOCK KNOB To lock the door without the key move the inside lock knob to the lock position then close the door To unlock the door without the key move the inside lock knob to the unlock position 2 LOCKING WITH POWER DOOR LOCK SWITCH To lock all the doors without a key push the door lock switch driver s or front passenger s side to the lock position When locking the door this way be certain not to leave the key inside the vehicle To unlock all the doors without a key push the door lock switch driver s or front passenger s side to the unlock position Pre driving checks and adjustments 3 5 Lockout protection When the power door lock switch driver s or front passenger s side is moved to the lock position with the Intelligent Key in
352. ng the seat belt as outlined in this manual should not cause the passenger air bag to be automatically turned OFF For small adults it may be turned OFF however if the occu pant takes his her weight off the seat cushion for example by not sitting upright by sitting on an edge of the seat or by otherwise being out of position this could cause the sensor to turn the air bag OFF In addition if the occupant improperly uses the seat belt in the ALR mode child restraint mode this could cause the air bag to be turned OFF Always be sure to be seated and wearing the seat belt properly for the most effective protection by the seat belt and supplemental air bag NISSAN recommends that pre teens and chil dren be properly restrained in a rear seat NISSAN also recommends that appropriate child restraints and booster seats be properly installed in a rear seat If this is not possible the occupant classification sensor and seat belt sensors are designed to operate as described above to turn the front passenger air bag OFF for specified child restraints as required by the regulations Failing to properly secure child restraints and to use the ALR mode child restraint mode may allow the restraint to tip or move in an accident or sudden stop This can also result in the passen ger air bag inflating in a crash instead of being OFF See Child restraints earlier in this section for proper use and installation If the front passenger sea
353. ng vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an accident you could be thrown into it and receive neck or other serious injuries You could also slide under the lap belt and receive serious internal injuries For the most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat with both feet on the floor and adjust the seat properly See Precau tions on seat belt usage later in this section After adjustment gently rock in the seat to make sure it is securely locked Do not leave children unattended inside the vehicle They could unknowingly ac tivate switches or controls Unattended children could become involved in seri ous accidents 1 2 Safety Seats seat belts and supplemental restraint system Do not adjust the drivers seat while driving so full attention may be given to vehicle operation The seat may move suddenly and could cause loss of con trol of the vehicle The seatback should not be reclined any more than needed for comfort Seat belts are most effective when the pas senger sits well back and straight up in the seat If the seatback is reclined the risk of sliding under the lap belt and being injured is increased A CAUTION When adjusting the seat positions be sure not to contact any moving parts to avoid possible injuries and or damage FRONT POW
354. ngine oil to ensure satisfactory engine life and performance See Capacities and recommended fuel lubricants earlier in this section NISSAN recommends the use of an energy conserving oil in order to improve fuel economy Select only engine oils that meet the American Petroleum Institute API certification or Interna tional Lubricant Standardization and Approval API service symbol Committee ILSAC certification and SAE vis cosity standard These oils have the API certifica tion mark on the front of the container Oils which do not have the specified quality label should not be used as they could cause engine damage Oil additives NISSAN does not recommend the use of oil additives The use of an oil additive is not neces sary when the proper oil type is used and main tenance intervals are followed Oil which may contain foreign matter or has been previously used should not be used Oil viscosity The engine oil viscosity or thickness changes with temperature Because of this it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper ated before the next oil change Choosing an oil viscosity other than that recommended could cause serious engine damage Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high quality genuine NISSAN oil filter When re placing use a genuine NISSAN oil filter or its equivalent for the reason describe
355. nit If the vehicle becomes involved in a collision but a pretensioner is not acti vated be sure to have the pretensioner system checked and if necessary re placed by your NISSAN dealer e No unauthorized changes should be made to any components or wiring of the pretensioner system This is to pre vent damage to or accidental activation of the pretensioners Tampering with the pretensioner system may result in serious personal injury Work around and on the pretensioner system should be done by a NISSAN dealer Installation of electrical equip ment should also be done by a NISSAN dealer Unauthorized electrical test equipment and probing devices should not be used on the pretensioner system If you need to dispose of a pretensioner or scrap the vehicle contact a NISSAN dealer Incorrect disposal procedures could cause personal injury The pretensioner system may activate with the supplemental air bag system in certain types of collisions Working with the seat belt retractor the pretensioner helps tighten the seat belt when the vehicle becomes involved in certain types of collisions helping to restrain front seat occu pants The pretensioner is encased within the seat belt retractor These seat belts are used the same way as conventional seat belts When a pretensioner activates smoke is re leased and a loud noise may be heard This smoke is not harmful and does not indicate a fire Care should be taken
356. nition switch is in the ON position The power moonroof is operational for a period of time even if the ignition switch is placed in the ACC or OFF position If the driver s door or the front passen ger s door is opened during this period of time the power to the moonroof is canceled Instruments and controls 2 47 Sliding the moonroof To slide the moonroof To fully open the moonroof push the switch C toward the open position until it reaches the second detent If the switch is pushed to the first detent only the sunshade will open To fully close the moonroof push the switch 2 toward the close position until it reaches the second detent If the switch is pushed to the first detent the moonroof will close but the sunshade will remain open To open or close the moonroof part way release the switch 1 or 2 while the moon roof is sliding open or closed The moonroof will stop at the desired position Tilting the moonroof To tilt the moonroof To tilt the moonroof up push and release the tilt switch 3 When the moonroof is open it will automatically close and then tilt up To tilt the moonroof down push and release the tilt switch or push the switch toward the close position until it reaches the first detent 2 48 Instruments and controls To tilt the moonroof down and close the sunshade at the same time push the switch 2 to the close position until it reaches the second de
357. nk in the mainte nance chain Scheduled maintenance For your convenience both required and optional scheduled maintenance items are described and listed in your NISSAN Service and Maintenance Guide You must refer to that guide to ensure that necessary maintenance is performed on your NISSAN at regular intervals General maintenance General maintenance includes those items which should be checked during normal day to day op eration They are essential for proper vehicle op eration It is your responsibility to perform these maintenance procedures regularly as prescribed 8 2 Maintenance and do it yourself Performing general maintenance checks requires minimal mechanical skill and only a few general automotive tools These checks or inspections can be done by you a qualified technician or if you prefer a NISSAN dealer Where to go for service If maintenance service is required or your vehicle appears to malfunction have the systems checked and corrected by a NISSAN dealer NISSAN technicians are well trained specialists who are kept up to date with the latest service information through technical bulletins service tips and in dealership training programs They are completely qualified to work on NISSAN ve hicles before they work on your vehicle rather than after they have worked on tt You can be confident that a NISSAN dealer s service department performs the best job to meet the maintenance require
358. not pressed for approximately 10 seconds the radio or CD display will automatically reappear Clock operation For additional information on setting the clock see Adjusting the time in this section Monitor climate audio phone and voice recognition systems 4 57 CD MP3 display mode While listening to a CD or an MP3 WMA CD certain text might be able to be displayed when CD encoded with text is being used Depending on how the CD or MP3 WMA CD is encoded the following text might be able to be displayed by selecting the Text key Folder displays the name of the current folder being accessed File displays the name of the file currently playing Song displays the ID3 encoded tag of the song name CD gt Text i l Folder XXXXXXX File XXXXXXX Mp3 Song XXXXXXX Album Artist XXXXXXX XXXXXXX Album displays the ID3 encoded tag of the album name e Artist displays the ID3 encoded tag of the artist s name Disc displays the disc name of the CD cur rently playing Track displays the name of the song on the CD currently playing Some of this text or modes might not display while playing a regular CD Select the Menu key with the NISSAN controller then select the Text key to display the text for the CD 4 58 Monitor climate audio phone and voice recognition systems Press the BACK button to exit the CD text display screen FM AM SAT radio operation F
359. ns Always maintain a safe distance from the vehicle in front of you Ultimately the driver is respon sible for safety Tire type and condition may also affect braking effectiveness When replacing tires install the specified size of tires on all four wheels When installing a spare tire make sure that it is the proper size and type as specified on the Tire and Loading Information label See Tire and Loading Information label in the Technical and consumer informa tion section of this manual For detailed information see Wheels and tires in the Mainte nance and do it yourself section of this manual The Anti lock Braking System ABS controls the brakes so the wheels do not lock during hard braking or when braking on slippery surfaces The system detects the rotation speed at each wheel and varies the brake fluid pressure to pre vent each wheel from locking and sliding By preventing each wheel from locking the system helps the driver maintain steering control and helps to minimize swerving and spinning on slip pery surfaces Using the system Depress the brake pedal and hold it down De press the brake pedal with firm steady pressure but do not pump the brakes The ABS will oper ate to prevent the wheels from locking up Steer the vehicle to avoid obstacles A WARNING Do not pump the brake pedal Doing so may result in increased stopping distances Self test feature T
360. nt intermittent wiper func tion for vehicles with navigation system Refer to Comfort settings in the Monitor climate audio phone and voice recogni tion systems section 2 Low continuous low speed operation 3 High continuous high speed operation Push the lever up 4 to have one sweep opera tion of the wiper Pull the lever toward you 8 to operate the washer The wiper will also operate several times AWARNING In freezing temperatures the washer solu tion may freeze on the windshield and obscure your vision which may lead to an accident Warm the windshield with the defroster before you wash the windshield A CAUTION Do not operate the washer continuously for more than 30 seconds Do not operate the washer if the windshield washer fluid reservoir is empty Do not fill the windshield washer fluid reservoir with washer fluid concen trates at full strength Some methyl al cohol based washer fluid concentrates may permanently stain the grille if spilled while filling the windshield washer fluid reservoir Pre mix washer fluid concentrates with water to the manufacturer s recom mended levels before pouring the fluid into the windshield washer fluid reser voir Do not use the windshield washer fluid reservoir to mix the washer fluid and water REAR WINDOW AND OUTSIDE MIRROR if so equipped DEFROSTER SWITCH LIC1387 Type A To defrost the rear window glass and outside mirrors
361. nt it from being dialed When the radio wave condition is not ideal or ambient sound is too loud it may be difficult to hear the other person s voice dur ing a call Immediately after the ignition switch is placed in the ON position it may be impos sible to receive a call for a short period of time Do not place the cellular phone in an area surrounded by metal or far away from the in vehicle phone module to prevent tone quality degradation and wireless connection disruption While a cellular phone is connected through the Bluetooth wireless connection the battery power of the cellular phone may dis charge quicker than usual The Bluetooth Hands Free Phone System cannot charge cellular phones If the hands free phone system seems to be malfunctioning see Troubleshooting guide in this section You can also visit www nissanusa com bluetooth for trouble shooting help Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers Stor ing the device in a different location may reduce or eliminate the noise Refer to the cellular phone owner s manual regarding the telephone charges cellular phone antenna and body etc The signal strength display on the monitor will not coincide with the signal strength display of some cellular phones If reception between callers is unclear ad justing the incoming or outgoing call volume may improve the clarit
362. ntil they are tight 4 Lower the vehicle slowly until the tire touches the ground Then with the wheel nut wrench tighten the wheel nuts securely in the sequence illustrated 5 Lower the vehicle completely AWARNING Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off This could cause an accident Do not use oil or grease on the wheel studs or nuts This could cause the nuts to become loose Retighten the wheel nuts when the ve hicle has been driven for 600 miles 1 000 km also in cases of a flat tire etc As soon as possible tighten the wheel nuts to the specified torque with a torque wrench Wheel nut tightening torque 83 ft lb 112 N m The wheel nuts must be kept tightened to specification at all times It is recom mended that wheel nuts be tightened to specifications at each lubrication interval Adjust tire pressure to the COLD pressure COLD pressure After vehicle has been parked for three hours or more or driven less than 1 mile 1 6 km COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver s door opening 5 Securely store the flat tire and jacking equip ment in the vehicle 6 Place the spare tire cover and the trunk floor carpeting over the damaged tire 7 Close the trunk AWARNING Always make sure that the spare tire and jacking equipment are pro
363. o conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device Instruments and controls 2 27 LICO474 Security indicator light The security indicator light blinks whenever the ignition switch is placed in the OFF LOCK or ACC position This function indicates the NISSAN Ve hicle Immobilizer System is operational If the NISSAN Vehicle Immobilizer System is mal functioning the light will remain on while the ignition switch is placed in the ON position If the light still remains on and or the en gine will not start see a NISSAN dealer for NISSAN Vehicle Immobilizer System ser vice as soon as possible Please bring all registered keys that you have when visiting your NISSAN dealer for service 2 28 Instruments and controls WINDSHIELD WIPER AND WASHER SWITCH SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position Push the lever down to operate the wiper at the following speed C Intermittent intermittent operation can be adjusted by turning the knob toward Slower or Faster Also the intermit tent operation speed varies in accordance with the vehicle speed For example when the vehicle speed is high the intermittent operation speed will be faster NOTE You can turn on or turn off the driving speed depende
364. o play e Copy control compact discs CCCD Recordable compact discs CD R Rewritable compact discs CD RW Recordable compact discs DVD R DVD R DL Rewritable compact discs DVD RW DVD RW DL Do not use the following CDs DVDs as they may cause the CD DVD player to malfunction 3 1 in 8 cm discs e CDs DVDs that are not round e CDs DVDs with a paper label e CDs DVDs that are warped scratched or have abnormal edges This audio system can only play pre recorded CDs DVDs It has no capa bilities to record or burn CDs DVDs If the CD DVD cannot be played one of the following messages will be dis played 4 38 Monitor climate audio phone and voice recognition systems Disc Read Error Confirm that the CD DVD is inserted correctly the label side is facing up etc Confirm that the CD DVD is not bent or warped and it is free of scratches Please Eject Disc This error may be due to the tempera ture inside the player getting too high Remove the CD DVD by pushing the EJECT button and after a short time reinsert the CD DVD The CD DVD can be played when the temperature of the player returns to normal If the error persists consult your local dealership Unplayable File The file may be copy protected The file is not MP3 WMA AAC M4A or DIVX type Region Invalid The DVD is not for region 1 or all regions e Use DVDs with a region code 1 ALL
365. of the instrument panel When the Intelligent Key is placed on top of the rear parcel shelf When the Intelligent Key is placed in side the glove box or a storage bin When the Intelligent Key is placed in side the door pockets When the Intelligent Key is placed on or under the spare tire area When the Intelligent Key is placed in side or near metallic materials Unlocking doors 1 Carry the Intelligent Key 2 Push the door handle request switch 4 3 The hazard warning lights flash once and the outside buzzer sounds once 4 Push the door handle request switch 1 again within 60 seconds to unlock all doors If a door handle is pulled while unlocking the doors that door may not be unlocked Returning the door handle to its original position will unlock the door If the door does not unlock after return ing the door handle push the door handle re quest switch to unlock the door Pre driving checks and adjustments 3 11 The interior light can be turned off without waiting by performing one of the following operations Placing the ignition switch in the ON posi tion Locking the doors with the remote controller Switching the room light switch to the OFF position All doors will be locked automatically unless one of the following operations is performed within 60 seconds after pushing the request switch Opening any door Pushing the ignition switch The interior li
366. old tire pressure is shown on the Tire and Theair conditioner specification label is affixedto location marks small dimples using the two Loading Information label The label is located as the underside of the hood as shown 6 mm screws provided shown Technical and consumer information 9 11 VEHICLE LOADING INFORMATION AWARNING It is extremely dangerous to ride in a cargo area inside a vehicle In a collision people riding in these areas are more likely to be seri ously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts e Be sure everyone in your vehicle is in a seat and using a seat belt properly TERMS It is important to familiarize yourself with the following terms before loading your vehicle Curb Weight actual weight of your vehicle vehicle weight including standard and optional equipment flu ids emergency tools and spare tire assembly This weight does not in clude passengers and cargo 9 12 Technical and consumer information GVW Gross Vehicle Weight curb weight plus the combined weight of passengers and cargo GVWR Gross Vehicle Weight Rat ing maximum total combined weight of the unloaded vehicle pas sengers luggage hitch trailer tongue load and any other optional equipment This information is lo cated on the F M V S S C M V S S certification label GAWR Gross Axle Weight Rating maximu
367. om your cell phone depending on your phone s compatibility You may select one of these entries to save in the vehicle phonebook Copy from the Handset The system will show your cell phone s phonebook that was downloaded depending on your phone s compatibility You may select one of these entries to save in the vehicle phonebook Enter Number by Keypad Allows manual entry of phonebook contacts Ok Saves the phonebook entry and then will show a screen that is ready to call the number Press the BACK button to return to the Vehicle Phonebook Allows user to choose a type from the icon list Select the Voicetag key to record a name to speak when using the Voice Recognition system Select the Store key and prepare to speak the name after the tone When the voicetag is successfully saved select the OK key to save the phonebook entry 4 110 Monitor climate audio phone and voice recognition systems Press the button on the steering wheel or the Phone button on the control panel and then Changes the displayed number of the selected entry Edit the name of the entry using the keypad displayed on the screen select the Vehicle Phonebook key Next select nig Peren entry from the displayed list Select Edit the phone number using the keypad displayed on the screen the Edit key Select the icon from the icon list Voicetag Confirm and store the voicetag Voicetags allow easy dialing using the NISSAN
368. omy calculation can be reset to 0 Press the INFO button and select the Fuel Economy key then select the Re set key using the NISSAN controller Fuel Economy Record Fuel Economy Record Record Select the View key to display the average fuel consumption history in a graph form Maintenance Items Press the INFO button and select the Maintenance key using the NISSAN controller the maintenance information will be displayed on the screen Reminder keys 1 4 Engine Oil Oil Filter Tire or Other Reminder Oil Oil Filter Tire or Other Reminder Resetting the To reset the reminder schedule Eere O Ol Eter ee to O mi km select the Reset Distance key using the NISSAN controller maintenance in terval Interval Reminder Displays status of the selected interval reminder Select to toggle on or off If set to On the maintenance notice screen will be dis played once the interval is met and the ignition switch is placed in the OFF and then ON position Monitor climate audio phone and voice recognition systems 4 7 Settings 8 00 Settings Display Switch Beeps Camera Clock Down Adjust tone amp advanced audio settings Adjust tone amp advanced audio settings tone amp advanced audio settings HOW TO USE THE SETTING BUTTON Press the SETTING button This screen displays and adjusts various settings and functions that are available for your vehicle Use the NI
369. on Ds Drive Sport mode Move the shift lever over from D Drive to the left into the manual shift gate The position indicator in the meter shows a Ds In Ds Drive Sport mode transmission operation changes to Sporty driving shift operation creating a more ag gressive acceleration feeling than the D Drive mode and a gear change sensation when the driver accelerates quickly When the driver selects M Manual mode ratio with shift lever or shift paddles if so equipped during Ds Drive Sport mode operation the driver must move the shift lever from Ds mode to D mode and back again to re select Ds Drive Sport mode To cancel the Ds mode return the shift lever to the D Drive position The transmission returns to the automatic drive mode The CVT can operate in two manual drive modes M Manual mode With the shift lever in the manual shift gate Ds Drive Sport mode M Manual mode can be selected by moving the shift lever up or down or using the shift paddles if so equipped up or down In M mode the transmission will pro duce noticeable upshifts and downshifts The position indicator in the meter shows a M Temporary M Manual shift mode With the shift lever in the D Drive mode and if the shift paddle is moved up or down the transmission will temporarily switch to the M Manual mode If the shift paddles are not used after 5 10 seconds the transmissio
370. on Displays Audio commands Displays User Guide Phone Commands COMMAND ACTION FACTION O O Navigation Commands COMMAND ACTION Sets a route to your home that is stored in the Address Book Allows user to set destination address Sets a route to a facility near the current vehicle location Address Book Searches for a location stored in the Address Book Previous Destinations Sets a route to a previous destination Monitor climate audio phone and voice recognition systems 4 123 Vehicle Information Commands COMMAND ACTION Fuel Economy Displays Fuel Economy information Displays Maintenance information Traffic Information Turns the traffic information system on and off Displays current vehicle locaton Audio Commands COMMAND ACTION AM Changes the audio system mode to AM radio FFM Changes the audio system mode to FM radio Changes the audio system mode to XM radio Changes the audio system mode to CD 4 124 Monitor climate audio phone and voice recognition systems Voice command examples Some basic voice command examples are de scribed here For navigation system commands see the sepa rate Navigation System Owner s Manual Example 1 Placing a call to the phone number 800 662 6200 1 O O A W Press the amp button located on the steer ing wheel The system announces Would you like to access Phone Navigation Information Au dio or Hel
371. on and illegal drugs Don t drive if your ability to operate your vehicle is impaired by alcohol drugs or some other physical condition PUSH BUTTON IGNITION SWITCH AWARNING Do not operate the push button ignition switch while driving the vehicle except in an emergency The engine will stop when the ignition switch is pushed 3 consecu tive times in quick succession or the igni tion switch is pushed and held for more than 2 seconds If the engine stops while the vehicle is being driven this could lead to a crash and serious injury When the ignition switch is pushed without de pressing the brake pedal the ignition switch po sition will illuminate as follows Push the ignition switch center once to change to ACC two times to change to ON three times to return to OFF The ignition switch will automatically return to the LOCK position when any door is either opened or closed with the switch in the OFF position Starting and driving 5 7 The ignition lock is designed so that the ignition switch position cannot be switched to OFF until the shift lever is moved to the P Park position When the ignition switch cannot be pushed to ward the OFF position proceed as follows 1 Move the shift lever into the P Park posi tion 2 Push the ignition switch The ignition switch position will change to the ON position 3 Push the ignition switch again to the OFF position The shift lever can be moved
372. on press the PHONE SEND 46 button To go back to the previous menu press the PHONE END 4 button If the current menu is the Main Menu pressing the PHONE END 4 button will exit the Phone system To exit the manual control mode press and hold the PHONE END button for 5 seconds 4 104 Monitor climate audio phone and voice recognition systems TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty If problems are en countered try the following solutions Where the solutions are listed by number try each solution in turn starting with number 1 until the problem is resolved Symptom System fails to interpret the command correctly The system consistently selects the wrong entry from the phone book Solution 1 Ensure that the command is valid See List of voice commands in this section 2 Ensure that the command is spoken after the tone 3 Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the vehicle 4 Ensure that the ambient noise level is not excessive for example windows open or defroster on NOTE If it is too noisy to use the phone it is likely that the voice commands will not be recognized 5 If more than one command was said at a time try saying the commands separately 6 If the system consistently fails to recognize commands the voice training procedure should be car
373. on and seatback Such objects may interfere with the proper operation of the occupant classification sensor pattern sensor No unauthorized changes should be made to any components or wiring of the seat belt system This may affect the front air bag system Tampering with the seat belt system may result in seri ous personal injury Work on and around the front air bag system should be done by a NISSAN dealer Installation of electrical equip ment should also be done by a NISSAN dealer The Supplemental Restraint System SRS wiring should not be modified or disconnected Unauthor ized electrical test equipment and prob ing devices should not be used on the air bag system e A cracked windshield should be re placed immediately by a qualified repair facility A cracked windshield could af fect the function of the supplemental air bag system The SRS wiring harness connectors are yellow and orange for easy identification When selling your vehicle we request that you inform the buyer about the front air bag system and guide the buyer to the appropriate sections in this Owner s Manual Safety Seats seat belts and supplemental restraint system 1 53 eS i Vi S P A Front seat mounted side impact supplemental air bag and roof mounted curtain side impact supplemental air bag systems The side air bags are located in the outside of the seatback of the front seats The curtain air bags are located in the side
374. on is pressed while a compact disc is being played the compact disc will eject and the last source will be played CD IN indicator The slot numbers 1 6 will illuminate if CDs have been loaded into the changer in CD mode only AUX IN jack The AUX IN jack is located on the CD changer The AUX IN audio input jack accepts any stan dard analog audio input such as from a portable cassette tape player MP3 player or a laptop computer Press the AUX button to play a compatible device when it is plugged into the AUX IN jack Monitor climate audio phone and voice recognition systems 4 55 No satellite radio reception is available when the AUX button is pressed to ac cess satellite radio stations unless op tional satellite receiver and antenna are installed and a SiriusXM Satellite Radio service subscription is active Satellite E 3 radio is not available in Alaska Hawaii 4 5 6 and Guam KONE QLORs ee FM AM SAT RADIO WITH MPACT DI D PLAYER if FMAM DISC AUX SOME TRUE if so equipped RPT SEEK SZ For all operation precautions see Audio opera SCAN RDM E CAT TRACK USH RI tion precautions in this section Audio main operation VOL ON OFF control Place the ignition switch in the ACC or ON position and push the VOL ON OFF control knob while the system is off to call up the mode that was playing immediately before the system was turned off To turn the system off pres
375. on is pressed with a com pact disc loaded with the radio playing the radio will automatically be turned off and the compact disc will start to play 44 gt p SEEK CAT and TRACK buttons When the SEEK CAT M4 button is pressed while a compact disc is playing the track being played returns to its beginning Press several times to skip back through tracks The compact disc will go back the number of times the button is pressed When the TRACK PPI button is pressed while a compact disc is playing the next track will start to play from its beginning Press several times to skip through tracks The compact disc will ad vance the number of times the button is pressed When the last track on the compact disc is skipped through the first track will be played The NISSAN controller can also be used to se lect tracks when a CD is playing 44 gt gt SEEK CAT and TRACK Rewind and Fast Forward buttons Press and hold the SEEK CAT M4 rewind button or the TRACK PPI fast forward button while a compact disc is playing the compact disc will play while rewinding or fast forwarding When the button is released the compact disc will return to normal play speed 4 60 Monitor climate audio phone and voice recognition systems TUNE FOLDER knob While playing an MP3 WMA CD turn the TUNE FOLDER knob right or left to scan forward or backward through available folders RPT RDM button When the RPT RDM button i
376. on systems 4 53 Compact disc CD changer operation Place the ignition switch in the ACC or ON position and press the LOAD button then press one of the CD insert 1 6 slots Insert the compact disc into the slot with the label side facing up The compact disc will be guided auto matically into the slot and start playing If the radio is already operating it will automati cally turn off and the compact disc will play If the system has been turned off while a compact disc was playing pressing the VOL ON OFF control knob will start the compact disc LOAD button To insert a CD in the CD changer press the LOAD button for less than 1 5 seconds Select the loading slot by pressing the CD insert select button 1 6 then insert the CD To insert 6 CDs to the CD changer press the LOAD button for more than 1 5 seconds The slot numbers 1 6 will illuminate on the display when CDs are loaded into the changer DISC button When the DISC button is pressed with the sys tem off and a compact disc loaded the system will turn on and the compact disc will start to play When the DISC button is pressed with a com pact disc loaded with the radio playing the radio will automatically be turned off and the compact disc will start to play 44 pp SEEK CAT and TRACK buttons When the SEEK CAT 4 button is pressed while a compact disc is playing the track being played returns to its beginning Press several
377. onditioner controls a 6b ke we we we ee a 4 30 4 34 Servicing air conditioner 4 36 Alarm system See vehicle security system 2 26 Anchor point locations 1 29 ANIONA 6s Sw oo dane oe ee ee a Be 2 4 91 Anti lock brake warning light 2 10 2 11 Anti lock Braking System ABS 5 25 Armrests 0 ee es te7 Audible reminders 2 16 Audio system Kia 6 a ee we ad wows 4 36 Bluetooth audio 4 85 Compact Disc CD changer 4 54 Compact disc CD player 4 60 4 67 FM AM radio with compact disc CD changer 6 6 545 4 51 FM AM SAT radio with CD DVD player 4 64 FM AM SAT radio with compact disc CD Playor shee ten ede ee Oe eo oe eae 4 57 Audio System iPod Player 4 79 4 82 Audio system Radio 6462464 3 5 o60 8 ae Romo 4 36 Steering wheel audio control switch 4 89 USB interface 4 74 4 76 Autolight switch 2 646 2 6 88 0 828s 2 32 Automatic Automatic drive positioner 3 30 Automatic power window switch 2 46 Automatic transmission position indicator NOW a amp 4 eo a 6 eB re ed Se ee 2 14 Transmission shift selector lock release 5 17 Automatic anti glare inside mirror 3 26 Automatic door locks 3 6 AUX jack tue we OES Ow whe 4 56 B Bate ie ee Bow ee oe oe eS 8 15 Charge warning light 2 11 Before starting the engine anaan
378. onitor climate audio phone and voice recognition systems Select the Full Screen Display key and press the ENTER button to view a full screen version of the image Image requirements Image type JPEG File extensions jpg jpeg Maximum resolution 2048 x 1536 Maximum size 2 MB Colors 32 768 15 bit Maximum file name length 253 bytes dis play only shows first 8 characters Maximum folders 500 Maximum images per folder 1024 8 00 Settings LHA1310 Slideshow settings Viewing images in a slideshow To view all of the images on the device in a slideshow first enter the full screen mode while viewing one of the images The slideshow control buttons are located on the right side of the screen While in slideshow mode the following settings can be accessed C Slideshow Speed Changes the frequency at which images are changed during a slideshow Choose one of the options on the screen or No Auto Change to have the images not change automatically o Slideshow Order Select the play key to begin the slideshow The images shown on the screen will periodically change at a given interval of time To skip through the images without waiting for them to change automatically select the M4 key to skip back ward or the P key to skip forward Select the stop key W to end the slideshow and return to the full screen display of the image currently on the screen Changes images in a
379. only the driver s side window can be opened or closed Push it again to cancel the window lock function of N LIC0410 Automatic operation To fully open a window equipped with automatic operation press the window switch down to the second detent and release it it need not be held The window automatically opens all the way To stop the window lift the switch up while the window is opening To fully close a window equipped with automatic operation pull the switch up to the second detent and release it it need not be held To stop the window press the switch down while the window is closing Auto reverse function The auto reverse function can be activated when a window is closed by automatic operation Depending on the environment or driving conditions the auto reverse function may be activated if an impact or load similar to something being caught in the window oc curs A WARNING There are some small distances immedi ately before the closed position which cannot be detected Make sure that all passengers have their hands etc inside the vehicle before closing the window If the vehicle s battery is disconnected replaced or jump started the power window auto reverse function may not operate properly If this occurs please contact the dealer to re initialize the power window auto reverse system If the control unit detects something caught in a window equipped with automatic operation as It is Closing
380. ontrols The life of xenon headlights will be shortened by frequent on off opera tion It is generally desirable not to turn off the headlights for short intervals for example when the vehicle stops at a traffic signal If the xenon headlight bulb is close to burning out the brightness will drasti cally decrease the light will start blink ing or the color of the light will become reddish If one or more of the above signs appear contact a NISSAN dealer Type A WIC1435 ning to battery WIC1436 Type B HEADLIGHT CONTROL SWITCH Lighting AM When turning the switch to the D posi tion the front parking tail license plate and instrument panel lights come on 2 When turning the switch to the 2 posi tion the headlights come on and all the other lights remain on A CAUTION Use the headlights with the engine run avoid discharging the vehicle Autolight system The autolight system allows the headlights to be set so they turn on and off automatically The autolight system can Turn on the headlights front parking tail license plate and instrument panel lights au tomatically when it is dark Turn off all the lights when it is light Keep all the lights on for a period of time after you place the ignition switch in the OFF position and all doors are closed Instruments and controls 2 31 To turn on the autolight system 1 Place the headlight switch in the AUTO po
381. ooling system additives are not necessary AWARNING Never remove the radiator or coolant reservoir cap when the engine is hot Wait until the engine and radiator cool down Serious burns could be caused by high pressure fluid escaping from the radiator See precautions in If your vehicle overheats found in the In case of emergency section of this manual The radiator is equipped with a pres sure type radiator cap To prevent en gine damage use only a genuine NISSAN radiator cap 8 8 Maintenance and do it yourself A CAUTION Never use any cooling system additives such as radiator sealer Additives may clog the cooling system and cause dam age to the engine transmission and or cooling system When adding or replacing coolant be sure to use only Genuine NISSAN Long Life Antifreeze Coolant blue or equivalent Genuine NISSAN Long Life Antifreeze Coolant blue is pre diluted to provide antifreeze protection to 34 F 37 C If additional freeze protection is needed due to weather where you operate your vehicle add Genuine NISSAN Long Life Antifreeze Coolant blue concentrate following the direc tions on the container If an equivalent coolant other than Genuine NISSAN Long Life Antifreeze Coolant blue is used follow the coolant manufacturer s instructions to maintain minimum anti freeze protection to 34 F 37 C The use of other types of coolant solutions other than Genuine NISSA
382. op or park the vehicle over flammable materials such as dry grass waste paper or rags They may ignite and cause a fire A CAUTION e Do not use leaded gasoline Deposits from leaded gasoline will seriously re duce the three way catalyst s ability to help reduce exhaust pollutants Keep your engine tuned up Malfunc tions in the ignition fuel injection or electrical systems can cause overrich fuel flow into the three way catalyst causing it to overheat Do not keep driv ing if the engine misfires or if notice able loss of performance or other un usual operating conditions are detected Have the vehicle inspected promptly by a NISSAN dealer Avoid driving with an extremely low fuel level Running out of fuel could cause the engine to misfire damaging the three way catalyst Do not race the engine while warming it up Do not push or tow your vehicle to start the engine TIRE PRESSURE MONITORING SYSTEM TPMS Each tire including the spare if provided should be checked monthly when cold and in flated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label you should determine the proper tire inflation pressure for those tires As an added safety feature your vehicle has been equipped with a tire pressure monitori
383. operat ing conditions due to premature tire failure or unfavorable han dling characteristics and could also lead to a serious accident Loading beyond the specified ca pacity may also result in failure of other vehicle components e Before taking a long trip or whenever you heavily load your vehicle use a tire pressure gauge to ensure that the tire pressures are at the specified level Increase the cold tire inflation pressure as indicated in Check ing tire pressure later in this sec tion when using the tires speci fied by NISSAN above 100 MPH 162 km h where it is legal to do so on a race track for example Failure to increase the cold tire inflation pressure may result in tire failure loss of control and possible injury After such use readjust tire pressure For additional information re garding tires refer to Important Tire Safety Information US or Tire Safety Information Canada in the Warranty Infor mation Booklet Maintenance and do it yourself 8 33 TIRE AND LOADING INFORMATION RENSEIGNEMENTS SUR LES PNEUS ET LE CHARGEMENT FRONT SEATING CAPACITY x NOMBRE DE PLACES Kap ARRIERE The combined weight of occupants QC and cargo should never exceed XX kg or XX Ibs Le poids total des occupants et du chargement ne doit jamais d passer XXX kg ou XXX Ibs Tire and loading information label Q Seating capacity The maximum num ber of occupants that can be seated in the vehicle
384. or Occupant classification system control unit 8 Seat belt buckle switches for driver s and passenger s side 9 Occupant classification sensor pattern sensor 10 Seat belt with pretensioner 11 Side satellite sensor NISSAN Advanced Air Bag System front seats This vehicle is equipped with the NISSAN Ad vanced Air Bag System for the driver and front passenger seats This system is designed to meet certification requirements under U S regu lations It is also permitted in Canada However all of the information cautions and warn ings in this manual still apply and must be followed The driver supplemental front impact air bag is located in the center of the steering wheel The passenger supplemental front impact air bag is mounted in the instrument panel above the glove box The front air bags are designed to inflate in higher severity frontal collisions although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact They may not inflate in certain frontal collisions Vehicle damage or lack of it is not always an indication of proper front air bag sys tem operation Safety Seats seat belts and supplemental restraint system 1 49 The NISSAN Advanced Air Bag System has dual stage inflators It also monitors information from the crash zone sensor the Air Bag Control Unit ACU seat belt buckle sensors and the occu pant classification sensor patte
385. or about 7 seconds and then turns off This means the system Is operational If any of the following conditions occur the front air bag side air bag curtain air bag and preten sioner systems need servicing The supplemental air bag warning light re mains on after approximately 7 seconds The supplemental air bag warning light flashes intermittently The supplemental air bag warning light does not come on at all Under these conditions the front air bag side air bag curtain air bag or pretensioner systems may not operate properly They must be checked and repaired Take your vehicle to the nearest NISSAN dealer AWARNING If the supplemental air bag warning light is on it could mean that the front air bag side air bag curtain air bag and or preten sioner systems will not operate in an acci dent To help avoid injury to yourself or others have your vehicle checked by a NISSAN dealer as soon as possible Repair and replacement procedure The front air bags side air bags curtain air bags and pretensioners are designed to inflate on a one time only basis As a reminder unless it is damaged the supplemental air bag warning light remains illuminated after inflation has occurred Repair and replacement of these supplemental air bag systems should be done only by a NISSAN dealer When maintenance work is required on the ve hicle the front air bags side air bags curtain air bags pretensioners and related
386. or down hills The gauge needle returns to E Empty after the ignition is placed in the OFF position The low fuel warning light comes on when the amount of fuel in the tank is getting low 2 6 Instruments and controls Refill the fuel tank before the gauge regis ters E Empty The ib indicates that the fuel filler door is located on the driver s side of the vehicle A CAUTION if the vehicle runs out of fuel the SENSING Malfunction Indicator Light SOON MIL may come on Refuel as soon as possible After a few driving trips the ENGINE light should turn off If the light remains on after a few driving trips have the vehicle inspected by a NISSAN dealer For additional information see Mal function Indicator Light MIL later in this section COMPASS DISPLAY if so equipped This unit measures terrestrial magnetism and in dicates the heading direction of the vehicle With the ignition placed in the ON position press the button as described in the charts be low to activate various features of the automatic anti glare rearview mirror Push and hold the N Push button again for about 1 sec button for about ond to change settings Compass display toggles on off Feature Compass zone can be changed to 8 seconds i correct false compass readings 10 seconds Compass enters calibration mode For information about the automatic anti glare feature refer to Automatic ant
387. or hear the system working when starting the vehicle or accelerating but this is normal AUDIBLE REMINDERS Brake pad wear warning The disc brake pads have audible wear warnings When a disc brake pad requires replacement it makes a high pitched scraping sound when the vehicle is in motion whether or not the brake pedal is depressed Have the brakes checked as soon as possible if the warning sound is heard Key reminder chime A chime sounds if the driver s door is opened while the ignition switch is placed in the ACC or OFF position or placed in the OFF or LOCK position with the Intelligent Key left in the Intelli gent Key port Make sure the ignition switch is placed in the LOCK position and take the Intelli gent Key with you when leaving the vehicle Light reminder chime With the ignition switch placed in the OFF posi tion a chime sounds when the driver s door is opened if the headlights or parking lights are on Turn the headlight control switch off before leav ing the vehicle NISSAN Intelligent Key door buzzer The Intelligent Key door buzzer sounds if the Intelligent Key is left inside the vehicle when locking the doors When the buzzer sounds be sure to check both the vehicle and the Intelligent Key See NISSAN Intelligent Key in the Pre driving checks and adjustments section VEHICLE INFORMATION DISPLAY The vehicle information display 1 is located on the bottom of the speedometer
388. or less than 1 5 seconds to increase or decrease the track number Tilt up down for more than 1 5 seconds to increase or decrease the title number Press the ENTER button to select an item from the DVD display When the transparent operation menu ap pears the switch will control the menu USB if so equipped Tilt up down for less than 1 5 seconds to increase or decrease the track number Tilt up down for more than 1 5 seconds to increase or decrease the folder number Press the ENTER button to show the USB Menu Bluetooth Audio if so equipped Tilt up down for less than 1 5 seconds to increase or decrease the track number AUX Press the ENTER button to show the AUX Menu ANTENNA Window antenna The antenna pattern is printed inside the rear window A CAUTION Do not place metalized film near the rear window glass or attach any metal parts to it This may cause poor recep tion or noise When cleaning the inside of the rear window be careful not to scratch or damage the rear window antenna Lightly wipe along the antenna with a dampened soft cloth CAR PHONE OR CB RADIO When installing a CB ham radio or car phone in your vehicle be sure to observe the following precautions otherwise the new equipment may adversely affect the engine control system and other electronic parts AWARNING A cellular phone should not be used for any purpose while driving so full at
389. ot attach anything to the head restraint headrest stalks or remove the head restraint headrest Do not use the seat if the head restraint headrest has been removed If the head restraint headrest was removed rein stall and properly adjust the head restraint headrest before an occupant uses the seating position Failure to fol low these instructions can reduce the effectiveness of the head restraints headrests This may increase the risk of serious injury or death in a collision The illustration shows the seating positions equipped with head restraints headrests The rear outboard seating positions are adjustable and removable The center rear position headrest does not adjust and is not removable A Indicates the seating position is equipped with a head restraint E Indicates the seating position is equipped with a headrest Indicates the seating position is not equipped with a head restraint or headrest Your vehicle is equipped with a head restraint headrest that may be integrated adjustable or non adjustable Adjustable head restraints headrests have multiple notches along the stalk to lock them in a desired adjustment position The non adjustable head restraints headrests have a single locking notch to secure them to the seat frame Proper Adjustment For the adjustable type align the head restraint headrest so the center of your ear is approximately level with the center of the head restraint headrest
390. ot match or the writing speed writing depth writing width etc might not match the Music cuts off or skips bee ae me specifications Try using the slowest writing speed Skipping with high bit rate Skipping may occur with large quantities of data such as for high bit rate data files Moves immediately to the If an unsupported compressed audio file has been given a supported extension like MP3 or when play is prohibited by copyright protection the next song when playing player will skip to the next song Songs do not play back in The playback order is the order in which the files were written by the writing software Therefore the files might not play in the desired order the desired order Random Shuffle may be active on the audio system or on the USB device 4 44 Monitor climate audio phone and voice recognition systems CD DVD or USB with Compressed Audio Files models with Navigation System The file types supported by this system are MP3 WMA AAC M4A and ATRACS Explanation of terms MP3 MP3 is short for Moving Pictures Experts Group Audio Layer 3 MP3 is the most well known compressed digital audio file format This format allows for near CD quality sound but at a fraction of the size of normal audio files MP3 conversion of an audio track can reduce the file size by ap proximately 10 1 ratio Sampling 44 1 kHz Bit rate 128 kbps with virtually no percep tible loss in quality The compression r
391. ount of space when compared to MP3s at the same level of quality Bit rate Bit rate denotes the number of bits per second used by a digital music file The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file Sampling frequency Sampling frequency is the rate at which the samples of a signal are converted from analog to digital A D conversion per second Multisession Multisession is one of the methods for writing data to media Writing data once to the media is called a single session and writing more than once is called a multisession e ID3 WMA Tag The ID3 WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title artist encoding bit rate track time duration etc ID3 tag infor mation is displayed on the Artist song title line on the display Windows Windows Media and Windows Vista are registered trademarks and trade marks in the United States of America and other countries of Microsoft Corporation of the USA Monitor climate audio phone and voice recognition systems 4 41 Playback order Music playback order of a CD with MP3 or WMA files is as illustrated The names of folders not containing MP3 or WMA files are not shown in the display lf there is a file in the top level of the disc Root Folder is displayed The playback order is the orde
392. out Navi gation system P 4 29 16 Audio system controls models without Navigation system P 4 35 cooocs 17 Front passenger air bag status light Coes o er 5 P 1 49 18 Audio system controls P 4 35 19 Climate controls models with Naviga tion system P 4 32 20 Shift lever P 5 12 1 Side and center vents P 4 28 4 Meters and gauges P 2 3 2 Headlight fog light if so equipped turn 5 Driver supplemental air bag horn oh Hazard nae Anner AG P 6 2 signal switch P 2 30 P 1 42 P 2 34 22 Ignition switch behind the steering 3 Steering wheel switch for audio control 6 Security indicator light P 2 26 wheel P 5 7 and Bluetooth Hands Free Phone 7 Cruise control main set switches 23 Tilt telescopic steering wheel controls System P 4 89 4 92 P 5 19 if so equipped P 3 22 0 6 Illustrated table of contents 24 Vehicle Dynamic Control VDC OFF switch P 2 37 Outside mirror controls P 3 27 Heated steering wheel switch if so equipped P 2 37 Trunk lid release switch P 3 19 Refer to the separate Navigation System Own er s Manual if so equipped See the page number indicated in paren theses for operating details Illustrated table of contents 0 7 ENGINE COMPARTMENT CHECK LOCATIONS 0 8 Illustrated table of contents 1 Power steering fluid reservoir P 8 13 2 Engine oil filler cap P 8 10 3 Brake fluid reservoir P 8 14
393. owing dollies under the front wheels When towing with the front wheels on towing dollies Place the ignition switch in the OFF position and secure the steering wheel in a straight ahead position with a rope or similar device Move the shift lever to the N Neutral position When towing CVT models with the rear wheels on the ground if you do not use towing dollies Always release the parking brake When towing CVT models with the front wheels on the ground dollies must be used or place the vehicle on a flat bed truck VEHICLE RECOVERY freeing a stuck vehicle Pulling a stuck vehicle AWARNING To avoid vehicle damage serious personal injury or death when recovering a stuck vehicle e Contact a professional towing service to recover the vehicle if you have any questions regarding the recovery procedure e Do not use the vehicle tie downs to tow or free a stuck vehicle Only use devices specifically designed for vehicle recovery and follow the manufacturer s instructions Always pull the recovery device straight out from the front of the vehicle Never pull at an angle Route recovery devices so they do not touch any part of the vehicle except the attachment point If your vehicle is stuck in sand snow mud etc use a tow strap or other device designed specifi cally for vehicle recovery Always follow the manufacturer s instructions for the recovery de vice Do not use t
394. p Say Phone Say Dial Number Say 800 The system announces Please say the next three digits or dial or say change number Say 662 The system announces Please say the last four digits or say change number 9 Say 6200 11 12 The system announces Dial or Change Number Say Dial The system makes a call to 800 662 6200 NOTE You can also speak 800 662 6200 10 continuous digits or 662 6200 7 con tinuous digits if the area code is not nec essary However the 3 3 4 digit grouping is recommended for improved recognition See How to speak numbers in this section You can only say a phone number using the 3 3 4 grouping 7 digits and 10 digits using this command Please use the International Call command for all other formats and when special characters such as star pound and plus need to be entered If you say Change Number during phone number entry the system will automatically request that you repeat the number using the 3 3 4 format In this case please say the area code first and then follow the prompts Monitor climate audio phone and voice recognition systems 4 125 Do not add a 1 in front of the area code when speaking phone numbers Ifthe system does not recognize your com mand please try repeating the command using a natural voice Speaking too slowly or too loud
395. parts should be pointed out to the person performing the mainte nance The ignition switch should always be placed in the LOCK position when working under the hood or inside the vehicle AWARNING Once a front air bag side air bag or curtain air bag has inflated the air bag module will not function again and must be replaced Additionally the acti vated pretensioner must also be re placed The air bag module and preten sioner should be replaced by a NISSAN dealer The air bag module and preten sioner cannot be repaired The front air bag side air bag curtain air bag systems and the pretensioner system should be inspected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle If you need to dispose of the supple mental air bag or pretensioner systems or scrap the vehicle contact a NISSAN dealer Incorrect disposal procedures could cause personal injury Safety Seats seat belts and supplemental restraint system 1 57 2 Instruments and controls INSUUMCNE panel sncsddeae sun deetedin ee ed tier sen 2 2 Meters and GaUGeSs di ccs tcc euteed eect euikeedeeuien oc 2 3 Speedometer and odometer 00ce eee aes 2 4 TACNOMGIC sc aseanceceess inated a E S cue 2 5 Engine coolant temperature gauge 2 5 Fuel gauge 2 ceeceeeonceee oper ee EEE eases a 2 6 Compass display if so equipped 00 e eee 2 6 Compass displays s0i lt saccvounes nkdleseertaenes
396. perly se cured after use Such items can become dangerous projectiles in an accident or sudden stop The spare tire is designed for emer gency use See specific instructions un der the heading Wheels and tires in the Maintenance and do it yourself section of this manual In case of emergency 6 7 JUMP STARTING To start your engine with a booster battery the instructions and precautions below must be fol lowed AWARNING If done incorrectly jump starting can lead to a battery explosion resulting in severe injury or death It could also damage your vehicle e Explosive hydrogen gas is always pres ent in the vicinity of the battery Keep all sparks and flames away from the battery Do not allow battery fluid to come into contact with eyes skin clothing or painted surfaces Battery fluid is a cor rosive sulfuric acid solution which can cause severe burns If the fluid should come into contact with anything imme diately flush the contacted area with water e Keep battery out of the reach of children The booster battery must be rated at 12 volts Use of an improperly rated battery can damage your vehicle 6 8 In case of emergency Whenever working on or near a battery always wear suitable eye protectors for example goggles or industrial safety spectacles and remove rings metal bands or any other jewelry Do not lean over the battery when jump starting Do not attempt
397. pervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in jured Keep the car locked with the rear seatback and trunk lid securely latched when not in use and prevent children s access to car keys To open the trunk lid push the opener switch down To close the trunk lid lower and push the trunk lid down securely NOTE You can open the trunk lid with the Intelli gent Key Refer to NISSAN Intelligent Key in this section a Kay LE Va Cancel switch When the cancel switch located inside the glove box is OFF the trunk lid cannot be opened with the trunk lid release switch or with the Intelligent Key INTERIOR TRUNK LID RELEASE AWARNING Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured Keep the car locked with the rear seatback and trunk lid securely latched when not in use and prevent children s access to car keys The interior trunk lid release mechanism provides a means of escape for children and adults in the event they become locked inside the trunk To open the trunk from the inside pull the illumi nated release handle until the lock releases and push up on the trunk lid The release handle is made of a material that glows in the dark after a brief exposure to ambient light The handle is loc
398. phone list and connecting instruc tions You will not be able to use a hands free phone under the following conditions Your vehicle is outside of the cellular ser vice area Your vehicle is in an area where it is difficult to receive a cellular signal such as in a tunnel in an underground parking garage near a tall building or in a moun tainous area Your cellular phone is locked to prevent it from being dialed When the radio wave condition is not ideal or ambient sound is too loud it may be difficult to hear the other person s voice dur ing a call Do not place the cellular phone in an area surrounded by metal or far away from the in vehicle phone module to prevent tone quality degradation and wireless connection disruption While a cellular phone is connected through the Bluetooth wireless connection the battery power of the cellular phone may dis charge quicker than usual The Bluetooth Hands Free Phone System cannot charge cellular phones If the hands free phone system seems to be malfunctioning see Troubleshooting guide in this section You can also visit www nissanusa com bluetooth for trouble shooting help Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers Stor ing the device in a different location may reduce or eliminate the noise Refer to the cellular phone Owner s Manual regarding the telephone charg
399. place any objects between any occupant and the steering wheel or instrument panel Such objects may be come dangerous projectiles and cause injury if the front air bags inflate Immediately after inflation several front air bag system components will be hot Do not touch them you may se verely burn yourself No unauthorized changes should be made to any components or wiring of the supplemental air bag system This is to prevent accidental inflation of the supplemental air bag or damage to the supplemental air bag system Do not make unauthorized changes to your vehicle s electrical system sus pension system or front end structure This could affect proper operation of the supplemental front air bag system Tampering with the front air bag system may result in serious personal injury Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the instrument panel or by installing additional trim material around the air bag system Modifying or tampering with the front passenger seat may result in serious personal injury For example do not change the front seats by placing mate rial on the seat cushion or by installing additional trim material such as seat covers on the seat that are not specifi cally designed to assure proper air bag operation Additionally do not stow any objects under the front passenger seat or the seat cushi
400. r Some states or provinces have specific regulations and speed limits for vehicles that are towing trailers Obey the local speed limits Check your hitch trailer wiring harness con nections and trailer wheel lug nuts after 50 miles 80 km of travel and at every break When launching a boat don t allow the wa ter level to go over the exhaust tail pipe or rear bumper Make sure you disconnect the trailer lights before backing the trailer into the water or the trailer lights may burn out When towing a trailer transmission fluid should be changed more frequently For additional information see the Mainte nance and do it yourself section earlier in this manual FLAT TOWING Towing your vehicle with all four wheels on the ground is sometimes called flat towing This method is sometimes used when towing a vehicle behind a recreational vehicle such as a motor home A CAUTION Failure to follow these guidelines can result in severe transmission damage Whenever flat towing your vehicle al ways tow forward never backward e DO NOT tow any automatic transmis sion vehicle with all four wheels on the ground flat towing Doing so WILL DAMAGE internal transmission parts due to lack of transmission lubrication For emergency towing procedures refer to Towing recommended by NISSAN in the In case of emergency section of this manual Continuously Variable Transmission To tow
401. r intake valve deposit removers etc which are sold commercially Many of these additives intended for gum varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent heavy spark knock Spark knock is a metallic rapping noise If se vere this can lead to engine damage If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating or if you hear steady spark knock while holding a steady speed on level roads have a NISSAN dealer correct the condition Failure to correct the condition is misuse of the vehicle for which NISSAN is not responsible Incorrect ignition timing may result in spark knock after run and or overheating which may cause excessive fuel consumption or engine damage If any of the above symptoms are en countered have your vehicle checked at a NISSAN dealer However now and then you may notice light spark knock for a short time while accelerating or driving up hills This is nota cause for concern because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load API certification mark ENGINE OIL AND OIL FILTER RECOMMENDATIONS Selecting the correct oil It is essential to choose the correct grade quality and viscosity e
402. r compart ment will be maintained automatically Air flow distribution and fan speed are also con trolled automatically Do not set the temperature lower than the outside air temperature Otherwise the sys tem may not work properly Not recommended if windows fog up Dehumidified defrosting or defogging 1 Press the TY front defroster button on The indicator light on the button will come on Turn the temperature control dial to set the desired temperature To quickly remove ice from the outside of the windows use the fan speed control dial to set the fan speed to maximum As soon as possible after the windshield is clean press the AUTO button to return to the automatic mode When the 7 front defroster button is pressed the air conditioner will automati cally be turned on at outside temperatures above 36 F 2 C The air recirculate mode automatically turns off allowing outside air to be drawn into the passenger compart ment to further improve the defogging per formance Monitor climate audio phone and voice recognition systems 4 33 MANUAL OPERATION Fan speed control Turnthe 8 fan speed control dial to manually control the fan speed Press the AUTO button to return to automatic control of the fan speed Air recirculation Press the gt air recirculation button to recir culate interior air inside the vehicle The C amp indicator light on the button will come on The air recircu
403. r in which the files were written by the writing software Therefore the files might not play in the desired order FOLDER MP3 or WMA WHA1078 Playback order chart 4 42 Monitor climate audio phone and voice recognition systems Specification chart Supported media CD CD R CD RW USB 2 0 CD CD R CD RW ISO9660 LEVEL1 ISO9660 LEVEL2 Romeo Joliet ISO9660 Level 3 packet writing is not supported Files saved using the Live File System component on a Windows Vista operating system based Supported file systems computer are not supported UDF Bridge UDF 1 02 ISO9660 UDF 1 5 UDF 2 0 VDF 1 5 VDF 2 0 packet writing is not supported MPEG1 MPEGS MPEG2 5 Sampling frequency frequency 8 kHz 48 kHz Supported geo rate 8 kbps 320 kbps VBR 2 versions WMA7 WMA8 8 kHz 48 He 8 kbps 320 kbps VBR 2 TE Folder levels Folder levels 8 Folders 255 including root folder Files 512 Max 255 files for one folder Text character number limitation 64 characters 01 ASCII 02 ISO 8859 1 03 UNICODE UTF 16 LE 04 UNICODE UTF 16 BE 05 UNI Displayable character codes 3 CODE UTF 8 1 Protected WMA files DRM cannot be played 2 When VBR files are played the playback time may not be displayed correctly 3 Available codes depend on what kind of media versions and information are going to be displayed Monitor climate audio phone and voice recognition systems 4 43
404. r outei rees weet aet tat ween bavedabeeeaie 2 38 Ol ACs E ae sees Ree E ab eeees vauwauee ewes 2 38 Map DOCKEIS 225 4 445 5 cekhdeceaeeateseta dca eee 2 38 Seatback pockets kc cvcedesvetseecedeenecaeine 2 39 Sunglasses NOIdEM sic cs sa cae cnene ad ena cede saie ak 2 39 CUP holde 22 35 e ict ee cere pee seen seeeres 2 40 OlGVe BOY pcuccetacceseeucatenccatesbeaeeaces 2 41 Dee DO wot nke cere tee ute eeeae see 2 41 GOCE NGCKS cece cacntenueetenwersseueces ox 2 42 Cargo net if so equipped 000 cece eens 2 42 WINDOWS tn acs ERE EE E EAEE eee ees 2 43 POWEL WIDGOWS seis cani eane a a A E nate 2 43 Moonroof if So equipped 0 0c cece eee eee 2 46 Power MOONOOlscastntuetebucesere nd eereweass 2 46 Dual Panel Moonroof if so equipped 2 47 POWEr MOONMOl csv causcvecsiedeeatenvercturs 2 47 Rear power sun shade if so equipped 2 49 mteror WOM 24 oe ee nni oni ae E N eure sue 2 50 CONnsOle NIGH i4ngudvennees Wek wy ew ease ane eayas 2 51 Personal IQs actocexeeceeucsesteaderss ances ee 2 51 Mop IMS 22 eccedemree vets aee a bese 2 53 onk IONE 2c22ceedeueenceteerteoeee eet ieee enede 2 2 53 HomeLink universal transceiver if so equipped Programming HomeLink sc0c1seseeceeneweewes Programming HomeLink for Canadian customers and gate openerSs 00005 Operating the HomeLink universal WANSCCWCl areara na E E ERNE AREA Programming trouble diagnosis 4 Clearin
405. random order when selected Changes images in the order in which they are saved on the USB device Monitor climate audio phone and voice recognition systems 4 21 REARVIEW MONITOR if so equipped When the shift lever is shifted into the R Re verse position the monitor display shows a rear ward view from the vehicle AWARNING The system is designed as an aid to the driver in detecting large stationary ob jects to help avoid damaging the ve hicle The system will not detect small objects below the bumper and may not detect objects close to the bumper or on the ground The rear view camera is a convenience but it is not a substitute for proper back ing up Always turn and check that it is safe to do so before backing up Always back up slowly Objects viewed in the RearView Moni tor differ from actual distance because a wide angle lens is used Make sure that the trunk is securely closed when backing up e Underneath the bumper and the corner areas of the bumper cannot be viewed on the RearView Monitor because of its monitoring range limitation e Do not put anything on the rear view camera The rear view camera is in stalled above the license plate When washing the vehicle with high pressure water be sure not to spray it around the camera Otherwise water may enter the camera unit causing wa ter condensation on the lens a mal function fire or an electric shock Do not strike the
406. rating could cause the wheels to skid and result in an accident If the engine is not running or is turned off while driving the power assist for the brakes will not work Braking will be harder Wet brakes When the vehicle is washed or driven through water the brakes may get wet As a result your braking distance will be longer and the vehicle may pull to one side during braking To dry the brakes drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes Do this until the brakes return to normal Avoid driving the vehicle at high speeds until the brakes function correctly Parking brake break in Break in the parking brake shoes whenever the effect of the parking brake is weakened or when ever the parking brake shoes and or drum rotors are replaced in order to assure the best brake performance This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer ANTI LOCK BRAKING SYSTEM ABS AWARNING The Anti lock Braking System ABS is a sophisticated device but it cannot pre vent accidents resulting from careless or dangerous driving techniques It can help maintain vehicle control during braking on slippery surfaces Remem ber that stopping distances on slippery surfaces will be longer than on normal surfaces even with ABS Stopping dis tances may also be longer on rough gravel or snow covered roads or if you are using tire chai
407. reen The side light and headlight indicator light illumi nates when the side light or headlight position is selected See Headlight and turn signal switch later in this section for further details R Slip indicator light This indicator will blink when the VDC system or the traction control system is operating thus alerting that the vehicle is nearing its traction limits The road surface may be slippery Turn signal hazard indicator lights The appropriate light flashes when the turn signal switch is activated Both lights flash when the hazard switch is turned on B Vehicle Dynamic Control VDC OFF indicator light This indicator light comes on when the Vehicle Dynamic Control off switch is pushed to OFF This indicates the Vehicle Dynamic Control has been turned off Push the Vehicle Dynamic Control off switch again or restart the engine and the system will be reactivated See Vehicle Dynamic Control VDC system in the Starting and driving sec tion of this manual The Vehicle Dynamic Control light also comes on when you push the push button ignition switch to the ON position The light will turn off after about 2 seconds if the system is operational If the light stays on or comes on along with the indi cator light while you are driving have the Vehicle Dynamic Control system checked by a NISSAN dealer While the Vehicle Dynamic Control system is operating you might feel slight vibration
408. res with those not originally specified by NISSAN could affect the proper operation of the TPMS A CAUTION The TPMS is not a substitute for the regular tire pressure check Be sure to check the tire pressure regularly If the vehicle is being driven at speeds of less than 16 MPH 25 km h the TPMS may not operate correctly Be sure to install the specified size of tires to the 4 wheels correctly Instruments and controls 2 13 Master warning light When the ignition is in the ON position the master warning light illuminates if any of the fol lowing are displayed on the vehicle information display No key warning Low fuel warning Low windshield washer fluid warning Parking brake release warning Door trunk open warning Loose fuel cap Check tire pressure warning Hi Seat belt warning light and r chime The light and chime remind you to fasten your seat belts The light illuminates whenever the ignition switch is placed in the ON or START position and remains illuminated until the driver s seat belt is fastened At the same time the chime sounds for about 6 seconds unless the driver s seat belt is securely fastened 2 14 Instruments and controls The seat belt warning light may also illuminate if the front passenger s seat belt is not fastened when the front passenger s seat is occupied For 7 seconds after the ignition switch is placed in the ON position the system does not activate the warning li
409. ressing the VOL ON OFF control knob will start the iPod AUX button When the AUX button is pressed with the system off and the iPod connected the system will turn on If another audio source is playing and the iPod is connected press the AUX button re peatedly until the center display changes to the iPod mode XXXXXX XXXXXX JI XXXXXX 0 02 Shuffle Off Repeat One i Use lt or gt buttons to move between left right menus Interface The interface for iPod operation shown on the vehicle center display is similar to the iPod interface Use the NISSAN controller and the BACK button to play the iPod with your favorite settings The following items can be chosen from the menu list screen For further information about each item see the iPod Owner s Manual e Playlists Podcasts Songs Monitor climate audio phone and voice recognition systems 4 81 Albums Artists Genres Composers Audiobooks The following keys shown on the screen are also available MENU returns to the previous screen e Pil plays pauses the music selected SEEK CAT and TRACK buttons When the 44 SEEK CAT button or gt gt TRACK button is pressed for less than 1 5 sec onds while the iPod is playing the next track or the beginning of the current track on the iPod will be played When the 44 SEEK CAT button or PP TRACK button is pressed for more than 1 5 sec onds while the iPod i
410. ried out to im prove the recognition response for the speaker See Voice Adaptation VA mode in this section 1 Ensure that the phone book entry name requested matches what was originally stored This can be confirmed by using the List Names command See Phonebook in this section 2 Replace one of the names being confused with a new name Monitor climate audio phone and voice recognition systems 4 105 BLUETOOTH HANDS FREE PHONE SYSTEM WITH NAVIGATION SYSTEM if so equipped AWARNING e Use a phone after stopping your vehicle in a safe location If you have to use a phone while driving exercise extreme caution at all times so full attention may be given to vehicle operation If you are unable to devote full attention to vehicle operation while talking on the phone pull off the road to a safe location and stop your vehicle A CAUTION To avoid discharging the vehicle battery use a phone after starting the engine z O Bluetooth Ml microphone location Your NISSAN is equipped with the Bluetooth Hands Free Phone System If you have a com patible Bluetooth enabled cellular phone you can set up the wireless connection between your cellular phone and the in vehicle phone module With Bluetooth wireless technology you can 4 106 Monitor climate audio phone and voice recognition systems make or receive a hands free telephone call with your cellular phone in the vehicl
411. rightness control button SETTING button P 4 8 P 4 10 4 4 Monitor climate audio phone and voice recognition systems A CAUTION The glass display screen may break if it is hit with a hard or sharp object If the glass screen breaks do not touch it Doing so could result in an injury To clean the display never use a rough cloth alcohol benzine thinner or any kind of solvent or paper towel with a chemical cleaning agent They will scratch or deteriorate the panel Do not splash any liquid such as water or car fragrance on the display Contact with liquid will cause the system to malfunction When you use this system make sure the engine is running If you use the system with the engine not running ignition ON or ACC for a long time it will discharge the battery and the engine will not start Reference symbols ENTER button This is a button on the control panel Example Words marked in quotes refer to a key shown on the display These keys can only be selected using the NISSAN controller HOW TO USE THE NISSAN CONTROLLER Use the NISSAN controller to choose an item on the display screen Highlight an item on the dis play using the main directional buttons 2 or the center dial Then press the ENTER button to select the item or perform the action The BACK button 4 has two functions e Go back to the previous display cancel If you press the BACK button
412. rm that the CD is inserted cor rectly the label side is facing up etc Confirm that the CD is not bent or warped and it is free of scratches PRESS EJECT This is an error due to excessive tem perature inside the player Remove the CD by pressing the EJECT button After a short time reinsert the CD The CD can be played when the temperature of the player returns to normal UNPLAYABLE The file is unplayable in this audio sys tem only MP3 or WMA if so equipped CD Monitor climate audio phone and voice recognition systems 4 37 CD DVD combination player models with Navigation System Do not force a disc into the CD DVD insert slot This could damage the CD DVD player During cold weather or rainy days the player may malfunction due to the hu midity If this occurs remove the CD DVD and dehumidify or ventilate the player completely The player may skip while driving on rough roads The CD DVD player sometimes cannot function when the passenger compart ment temperature is extremely high Decrease the temperature before use Only use high quality 4 7 in 12 cm round discs that have the COMPACT disc DIGITAL AUDIO or DVD Video logo on the disc or packaging Do not expose the CD DVD to direct sunlight CDs DVDs that are of poor quality dirty scratched covered with finger prints or that have pinholes may not work properly The following CDs DVDs are not guar anteed t
413. rmally 4 34 Monitor climate audio phone and voice recognition systems The sunload sensor located on the top driver s side of the instrument panel helps the system maintain a constant temperature Do not put any thing on or around this sensor SERVICING AIR CONDITIONER The air conditioner system in your NISSAN ve hicle is charged with a refrigerant designed with the environment in mind This refrigerant does not harm the earth s ozone layer Special charging equipment and lubricant is re quired when servicing your NISSAN air condi tioner Using improper refrigerants or lubricants will cause severe damage to your air conditioner system See Air conditioner system refrigerant and oil recommendations in the Technical and consumer information section of this manual A NISSAN dealer is able to service your environ mentally friendly air conditioning system AWARNING The air conditioner system contains refrig erant under high pressure To avoid per sonal injury any air conditioner service should be done only by an experienced technician with proper equipment AUDIO SYSTEM RADIO Place the ignition switch in the ACC or ON position and press the VOL volume ON OFF power knob to turn the radio on If you listen to the radio with the engine not running the ignition switch should be placed in the ACC position Radio reception is affected by station signal strength distance from radio tr
414. rn sensor Infla tor operation is based on the severity of a colli sion and seat belt usage for the driver For the front passenger the occupant classification sen sor is also monitored Based on information from the sensors only one front air bag may inflate ina crash depending on the crash severity and whether the front occupants are belted or un belted Additionally the front passenger air bag may be automatically turned OFF under some conditions depending on the weight detected on the passenger seat and how the seat belt is used If the front passenger air bag is OFF the passen ger air bag status light will be illuminated if the seat is unoccupied the light will not be illumi nated but the air bag will be off See Front passenger air bag and status light later in this section for further details One front air bag inflat ing does not indicate improper performance of the system If you have any questions about your air bag system please contact NISSAN or your NISSAN dealer If you are considering modification of your vehicle due to a disability you may also contact NISSAN Contact information is contained in the front of this Owner s Manual When a front air bag inflates a fairly loud noise may be heard followed by the release of smoke This smoke is not harmful and does not indicate a fire Care should be taken to not inhale it as it may cause Irritation and choking Those with a history of a breathing cond
415. rnings that may be present Once the screen is selected you have the option of skipping the warning or viewing it in detail Warnings can be present for issues such as an open door or low fuel For more information about potential warnings see Vehicle information dis play warnings and indicators later in this section If more than one warning is active the screen will cycle between the active warnings every 8 sec onds WARNING WARNING WARNING DOOR CHECK OPEN TIRE PRESSURE WARNING TIRE PRESSURES kk ce ede WARNING RELEASE PARKING BRAKE WARNING o0 RANGE 090 i om I Key System Error See Owner s Manual WARNING WARNING Loose Ea LOW wa A w WASHER w oe ma Vehicle information display warnings 4 Low windshield washer fluid warning 8 Engine start operation indicator and indicators 5 No key warning 9 NISSAN Intelligent Key insertion indicator 1 Door and trunk open warning 6 Parking brake warning 10 NISSAN Intelligent Key removal indicator 2 Push warning 7 Shift P warning 11 NISSAN Intelligent Key battery discharge 3 Low fuel warning indicator Instruments and controls 2 23 12 Loose fuel cap warning 13 Check tire pressure warning 14 Tire pressure warning 15 I Key System Error See Owner s Manual Door and trunk open warning This warning illuminates when a door or the trunk has been opened when the engine is running Push warning After the Shift P warning illumina
416. roce dure 1 Connect the battery cable or replace the fuse 2 Open and close the driver s door more than 2 times with the ignition switch in the LOCK position The entry exit function should now work properly SYSTEM OPERATION The automatic drive positioner system will not work or will stop operating under the following conditions When the vehicle speed is above 4 MPH 7 km h When any of the memory switches are pushed while the automatic drive positioner iS Operating When the adjusting switch for the driver s seat is turned on while the automatic drive positioner is operating When the seat has been already moved to the memorized position When no seat position is stored in the memory switch When the shift lever is moved from P Park to any other position When the driver s door remains open more than 45 seconds and the ignition switch is not in the ON position The automatic drive positioner system can be adjusted and canceled for vehicles with naviga tion system See Comfort amp convenience set tings and Comfort settings in the Monitor climate audio phone and voice recognition sys tems section of this manual 4 Monitor climate audio phone and voice recognition systems Control panel buttons color screen without Navigation System if so equipped 008 4 4 How to use the NISSAN controller 4 5 How to select menus on the
417. rom being left inside the vehicle make sure you carry the Intelligent Key with you and then lock the doors Do not pull the door handle before pushing the door handle request switch The door will be unlocked but will not open Release the door handle once and pull it again to open the door Pre driving checks and adjustments 3 9 NISSAN INTELLIGENT KEY OPERATION You can lock or unlock the doors without taking the Intelligent Key out of your pocket or bag When you carry the Intelligent Key with you you can lock or unlock all doors by pushing the door handle request switch within the range of opera tion 3 10 Pre driving checks and adjustments Locking doors 1 Move the shift lever to the P Park position Place the ignition switch in the LOCK posi tion Make sure the Intelligent Key is not left in the vehicle Close all doors Push any door handle request switch 4 while carrying the Intelligent Key with you All doors and the trunk will lock 5 The hazard warning lights flash twice and the outside buzzer sounds twice NOTE Doors lock with the door handle request switch when the ignition switch is placed in the ON position Doors lock with the door handle request switch while the ignition switch is not in the LOCK position Doors do not lock by pushing the door handle request switch while any door is open However doors lock with the me chanical key even if any door is op
418. rtain way to speak numbers when giving voice commands Refer to the following examples General rule Only single digits O zero to 9 can be used When saying the phone number 800 662 6200 the system will accept eight hundred in addition to eight zero zero or eight oh oh 500 700 and 900 are also supported Examples 1 800 662 6200 One eight zero zero six six two six two zero zero One eight hundred six six two six two zero zero 4 122 Monitor climate audio phone and voice recognition systems Improving Recognition of Phone numbers You can improve the recognition of phone num bers by saying the phone number in three groups of numbers For example when you try to call 800 662 6200 say eight zero zero first and the system will then ask you for the next three digits Then say six six two After recognition the system will then ask for the last four digits Say six two zero zero Using this method of phone digit entry can improve recognition perfor mance NOTE When speaking a house number speak the number 0 as zero or oh If the letter O is included in the house number it will not be recognized as 0 even if you speak oh instead of zero Standard Mode command list Category Commands COMMAND ACTION Displays Phone function commands Displays Navigation function commands Displays Vehicle Informati
419. s 3 3 Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle A CAUTION Do not allow the immobilizer system key which contains an electrical transponder to come into contact with water or salt water This could affect system function 3 4 Pre driving checks and adjustments DOORS When the doors are locked using one of the following methods the doors can not be opened using the inside or outside door handles The doors must be unlocked to open the doors AWARNING e Always have the doors locked while driving Along with the use of seat belts this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle This also helps keep children and others from unintentionally open ing the doors and will help keep out intruders e Before opening any door always look for and avoid oncoming traffic Do not leave children unattended inside the vehicle They could unknowingly ac tivate switches or controls Unattended children could become involved in seri ous accidents ozo a ano SS LPDO461 Driver s side LOCKING WITH KEY The power door lock system allows you to lock or unlock all doors at the same time Turning the key toward the front of the vehicle locks all doors Turning the key one time toward the rear 2 of the vehicle unlocks that door From that position returni
420. s feature allows you to access your phonebook from the Bluetooth system and call contacts by name You can record a custom voice tag for contact names that the system has difficulty recognizing For more information see Record name in this section NOTE Each phone has its own separate phone book You cannot access Phone A s phone book if you are currently connected with Phone B List Names Use the List Names command to hear all the names and locations in the phone book The system recites the phone book entries but does not include the actual phone numbers When the playback of the list is complete the system goes back to the main menu You can stop the playback of the list at any time by pressing the button on the steering wheel The system ends the VR session See the Record name command in this section for infor mation about recording custom voice tags for list entries that the system has difficulty pronounc ing Record Name The system allows you to record custom voice tags for contact names in the phonebook that the vehicle has difficulty recognizing This feature can also be used to record voice tags to directly dial an entry with multiple numbers Up to 40 voice tags can be recorded to the system Recent Calls Main Menu Recent Calls Outgoing Incoming Missed Call Back Redial Use the Recent Calls command
421. s of opening the driver s door push the memory switch 1 or 2 or Place the ignition switch in the ON position and push the memory switch 1 or 2 The driver s seat steering column and outside mirrors will move to the memorized position with the indicator light blinking and then the light will stay on for approximately 5 seconds ENTRY EXIT FUNCTION This system is designed so that the driver s seat and automatic operation steering column will au tomatically move when the shift lever is in the P Park position This allows the driver to get into and out of the driver s seat more easily 3 30 Pre driving checks and adjustments The drivers seat will slide backward and the steering wheel will move up when the driver s door is opened and the ignition switch is in the LOCK position The driver s seat and steering wheel will return to the previous position when the driver s door is closed and the ignition switch is pushed The entry exit function can be adjusted or can celed See Comfort amp Convenience settings and Comfort settings in the Monitor climate audio phone and voice recognition systems section of this manual Restarting the entry exit function If the battery cable is disconnected or if the fuse opens the entry exit function will be disabled Drive the vehicle over 25 MPH 40 km h to restart the entry exit function You can also restart the entry exit function using the following p
422. s opened during this period of time the switch poyer 1o ME WING OWS IE GANGEGA 5 Left rear passenger s side window switch 6 Driver s side automatic window switch Instruments and controls 2 43 Driver s side power window switch The driver s side control panel is equipped with switches to open or close all of the windows To open a window push the switch to the first detent and continue to hold down until the de sired window position is reached To close a window pull the switch to the first detent and continue to hold up until the desired window position is reached 2 44 Instruments and controls Front passenger s power window switch The passenger s window switch operates only the corresponding passenger s window To open the window push the switch to the first detent and continue to hold it down until the desired position is reached 1 To close the window pull the switch to the first detent and continue to hold o until the desired window position is reached It A LIC0718 Rear power window switch The rear power window switches open or close only the corresponding windows To open the window push the switch to the first detent and continue to hold it down until the desired window position is reached 1 To close the window pull the switch to the first detent and continue to hold up until the desired window position is reached Locking passengers windows When the window lock button is depressed
423. s playing the iPod will play while fast forwarding or rewinding When the button is released the iPod will return to the normal play speed iPod PLAYER OPERATION WITH NAVIGATION SYSTEM if so equipped Connecting iPod AWARNING Do not connect disconnect or operate the USB device while driving Doing so can be a distraction If distracted you could lose control of your vehicle and cause an acci dent or serious injury 4 82 Monitor climate audio phone and voice recognition systems A CAUTION e Do not force the USB device into the USB port Inserting the USB device tilted or up side down into the port may damage the port Make sure that the USB device is connected correctly into the USB port Do not grab the USB port cover if so equipped when pulling the USB device out of the port This could damage the port and the cover Do not leave the USB cable in a place where it can be pulled unintentionally Pulling the cable may damage the port Refer to your device manufacturer s owner infor mation regarding the proper use and care of the device To connect an iPod to the vehicle so that the iPod can be controlled with the audio system controls and display screen use the USB jack located in the center console Connect the iPod specific end of the cable to the iPod and the USB end of the cable to the USB jack on the vehicle 1 If your iPod supports charging via a USB connection its batt
424. s pressed while the compact disc is playing the play pattern can be changed as follows CD Repeat All 1 Track Repeat 1 Disc Random Repeat All CD with compressed audio files Repeat All 1 Folder Repeat 1 Track Repeat 1 Disc Random 1 Folder Random Re peat All Repeat All Normal play mode All tracks will constantly play in sequential order 1 Folder Repeat The folder that is currently being accessed will be repeated 1 Track Repeat The track that is currently playing will be repeated 1 Disc Random The tracks on the disc that is currently playing will be played in a mixed order 1 Folder Random The tracks in the folder that is currently playing will be played in a mixed order A CCD EJECT button Whenthe amp button is pressed with the com pact disc loaded the compact disc will be ejected When the amp button is pressed while the compact disc is being played the compact disc will eject and the system will turn off AUX auxiliary input jacks The auxiliary input jacks are located inside the center console NTSC compatible devices such as video games camcorders and portable video players can be connected to the auxiliary input jacks Audio devices such as some MP3 players can also be connected to the system through the auxiliary input jacks The auxiliary input jacks are color coded for iden tification purposes Red right channel audio input Whit
425. s the VOL ON OFF This vehicle has Speed Sensitive Volume SSV for audio The audio volume changes as the driv ing speed changes 1 A cD eject button 6 TRACK button control knob 9 VOL ON OFF control knob 7 SEEK CAT button Turn the VOL ON OFF control knob to adjust the 3 Station select 1 6 buttons 8 DISC button volume 4 TUNE FOLDER and AUDIO control 9 RPT RDM button i 11 knob Bass Treble Fade and Balance 0 SCAN button 5 AUX button 1 FM AM button 4 56 Monitor climate audio phone and voice recognition systems Audio control knob Pudi Adjusts the bass to the desired level Adjusts the treble to the desired level Adjusts the balance to the desired level Balance adjusts the sound level between the left and right speakers Adjusts the fade to the desired level Fade adjusts the sound level between the front and rear speakers Speed Sensitive Vol Adjusts the speed sensitive volume function which increases the volume of the audio system as the speed of the vehicle increases Set to OFF to disable the feature The higher the setting the more the volume increases in relation to vehicle speed Bass treble balance and fade can also be adjusted by pressing the AUDIO control knob and turning it to select the item to adjust When the desired item is shown on the display turn the tuning to adjust and then press the AUDIO button until the display returns to the main audio screen If the button is
426. s ue nrar reiti 7 6 Underbody sssigersisreisup yeri insid pisini 7 3 Most common factors contributing to vehicle GIIS S iesi a had othe ad tena iea maiia A E dei a 7 3 COMOSIOMioec ck cndsed sete temas EEE bees 7 6 Aluminum alloy wheels 00 00eceeeceew seen 7 3 Environmental factors influence the rate of Chrome paS s ersorsoitnsiscsisnradiai trisna ia s 7 4 CONOSION rieren reer ERARE NERAN EARE 7 6 Tire Ge sSiINGss ss cweceeeacn ect ecease eceeeeee s 7 4 To protect your vehicle from corrosion 7 6 Cleaning interior s s s seeavesadecun eee awe ad eaedn 7 4 CLEANING EXTERIOR In order to maintain the appearance of your ve hicle it is important to take proper care of it To protect the paint surfaces please wash your vehicle as soon as you can after a rainfall to prevent possible damage from acid rain after driving on coastal roads when contaminants such as soot bird drop pings tree sap metal particles or bugs get on the paint surface when dust or mud builds up on the surface Whenever possible store or park your vehicle inside a garage or in a covered area When it is necessary to park outside park in a shady area or protect the vehicle with a body cover Be careful not to scratch the paint surface when putting on or removing the body cover WASHING Wash dirt off with a wet sponge and plenty of water Clean the vehicle thoroughly using a mild soap a special vehicle soap or gen
427. se of emergency section for changing a flat tire When a spare tire is mounted or a wheel is replaced tire pressure will not be indicated the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute The light will remain on after 1 minute Contact your NISSAN dealer as soon as possible for tire replacement and or system resetting Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS Do not inject any tire liquid or aerosol tire sealant into the tires as this may cause a malfunction of the tire pressure sensors A CAUTION Do not place metalized film or any metal parts antenna etc on the windows This may cause poor reception of the signals from the tire pressure sensors and the TPMS will not function properly Some devices and transmitters may temporarily interfere with the operation of the TPMS and cause the low tire pressure warning light to illu minate Some examples are Facilities or electric devices using similar radio frequencies are near the vehicle lf a transmitter set to similar frequencies is being used in or near the vehicle If a computer or similar equipment or a DC AC converter is being used in or near the vehicle FCC Notice For USA This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 This device may not c
428. se the proper extension cord or a grounded outlet can result in a fire or electrical shock and cause serious personal injury To use the engine block heater 1 2 Turn the engine off Open the hood and unwrap the engine block heater cord Plug the engine block heater cord into a grounded 3 wire 3 pronged extension cord Plug the extension cord into a Ground Fault Interrupt GFI protected grounded 110 volt AC VAC outlet The engine block heater must be plugged in for at least 2 4 hours depending on outside temperatures to properly warm the engine coolant Use an appropriate timer to turn the engine block heater on Before starting the engine unplug and prop erly store the cord to keep it away from moving parts Starting and driving 5 29 MEMO 5 30 Starting and driving 6 In case of emergency Emergency engine shut off 2 2006 6 2 PUSM StaR ta ct twaceiueweendanee E AREARE 6 10 Hazard warning flasher switch 00e eee ee 6 2 If your vehicle overheats 2 02202e eee 6 10 Piel ies au ecncteacatue Mpoe een EE E E aanekews 6 3 Towing your VENICE cence cedkstecane ae eeteed nenn 6 11 Tire Pressure Monitoring System TPMS 6 3 Towing recommended by NISSAN 6 11 Changing a flat tire cece eens 6 3 Vehicle recovery freeing a stuck vehicle 6 12 JUMP Staring scc625vedcadeedederbedeteeedsesaad lt 6 8 EMERGENCY ENGINE SHUT OFF
429. secured against the vehicle seatback If necessary adjust or remove the head restraint headrest to obtain the correct child restraint fit If the head restraint headrest is removed store it in a secure place Be sure to reinstall the head restraint headrest when the child restraint is removed See Head restraints headrests in this sec tion for head restraint headrest adjustment information If the seating position does not have an adjustable head restraint headrest and it is interfering with the proper child restraint fit try another seating position or a different child restraint 1 34 Safety Seats seat belts and supplemental restraint system LRSO671 Forward facing step 4 4 For child restraints that are equipped with webbing mounted attachments remove any additional slack from the anchor attach ments Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments Tighten the tether strap according to the manufacturer s instructions to remove any slack WRS0697 Forward facing step 6 6 After attaching the child restraint test it be fore you place the child in it Push it from side to side while holding the child restraint near the LATCH attachment path The child re straint should not move more than 1 inch 25 mm from side to side Try to tug it forw
430. sed position which cannot be detected Make sure that all passengers have their hands etc inside the vehicle before closing the moonroof When closing If the control unit detects something caught in the moonroof as it moves to the front the moonroof will immediately open backward When tilting down If the control unit detects something caught in the moonroof as it tilts down the moonroof will im mediately tilt up If the auto reverse function malfunctions and re peats opening or tilting up the moonroof keep pushing the tilt down switch within 5 seconds after it happens the moonroof will fully close gradually Make sure nothing is caught in the moonroof AWARNING In an accident you could be thrown from the vehicle through an open moonroof Always use seat belts and child restraints e Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing A CAUTION e Remove water drops snow ice or sand from the moonroof before opening e Do not place heavy objects on the moonroof or surrounding area Sunshade Open and close the sunshade by sliding it for ward or backward If the moonroof does not close Have your NISSAN dealer check and repair the moonroof DUAL PANEL MOONROOF if so equipped CG OPEN ia 2 CLOSE A mwar POWER MOONROOF The moonroof will only operate when the ig
431. shown use the NISSAN controller or the touchscreen to select an item from the displayed menus EE PAUSE Select the II key to pause the DVD To re sume playing the DVD use the gt key p jee Select the key to start playing the DVD or resume playing the DVD after it has been paused ne Select the W key to stop playing the DVD lt lt l gt p NEXT PREVIOUS CHAPTER Select the PPI key to skip the chapter s of the disc forward Select the M4 key to skip the chapter s of the disc backward The chapters will advance forward or backward the number of times the respective key is touched or selected with the NISSAN controller Ki P CM SKIP This function is only for DVD VIDEO and DVD VR Selectthe I or l keyto fast forward or rewind a set interval of time based on the CM settings For more information see DVD set tings in this section Top Menu When the Top Menu key is selected while the DVD is playing the top menu specific to each disc will be displayed For details see the instruc tions attached to the disc DVD settings Select the Settings key to adjust the following settings Key DVD VIDEO Displays the operation keys for the specific DVD menu Select the directional keys to move the cursor on the DVD menu Select the Enter key to fix the selected menu item Select the Move key to move the loca tion of the operation keys on the scr
432. sition 2 Place ignition in the ON position 3 The autolight system automatically turns the headlights on and off Initially if the ignition switch is placed in the OFF position and a door is opened and left open the headlights remain ON for a period of time If another door is opened while the headlights are on then the timer is reset To turn the autolight system off turn the switch to the OFF P4 or 0 position 2 32 Instruments and controls Be sure you do not put anything on top of the autolight sensor located on the top side of the instrument panel The autolight sen sor controls the autolight if it is covered the autolight sensor reacts as if it is dark out and the headlights will illuminate If this occurs while parked with the engine off and the ignition switch placed in the ON position your vehicle s battery could be come discharged Headlight beam select To select the high beam function push the lever forward The high beam lights come on and the 20 light illuminates 2 Pull the lever back to select the low beam 3 Pulling and releasing the lever flashes the headlight high beams on and off Battery saver system If the ignition switch is placed in the OFF position while the headlight switch is in the Dd or 2 position the headlights will turn off after a period of time A CAUTION Even though the battery saver feature au tomatically turns off the headlights after a per
433. st amp Songs Tags the current artist or song playing on SiriusXM Satellite Radio as a favorite Turn the Alert ON to indicate whenever a favorite artist or song is playing on Sirius XM Satellite Radio The audio system must be playing Sirius XM Satellite Radio for this feature to work Delete a favorite artist or song Categories Displays a category list for SiriusXM Satellite Radio Select a category to select the first channel for that category Direct Tune Tune to a channel by entering the channel number Radio data system RDS RDS stands for Radio Data System and is a data information service transmitted by some radio stations on the FM band not AM band Cur rently most RDS stations are in large cities but many stations are now considering broadcasting RDS data RDS can display Station call sign such as WHFR 98 3 Station name such as The Groove Music or programming type such as Clas sical Country or Rock Station specific text If the station broadcasts RDS information the text information is automatically displayed Compact disc CD player operation Place the ignition in the ACC or ON position and insert the compact disc into the slot with the label side facing up The compact disc will be guided automatically into the slot and start playing If the radio is already operating it will automati cally turn off and the compact
434. stem is searching for your phone Using your handset look for a Bluetooth device called MY CAR When requested by the handset enter the PIN 1234 Ex iting screen cancels search The connecting procedure phone varies by phone See phone Owner s Manual for details When the connecting is complete the screen will return to the Bluetooth settings screen Cancel Cancels operation Indicates to the system that you are connecting a Bluetooth enabled audio device Cancel Cancels operation Monitor climate audio phone and voice recognition systems 4 109 VEHICLE PHONEBOOK This vehicle has two phonebooks available for your use Depending on your phone the system may automatically download your entire cell phone s phonebook into the Handset Phone book For the details on downloading your phonebook see Handset Phonebook in this section If your phonebook does not automati cally download you may set up the vehicle phonebook with up to 40 entries This phone book allows you to record a name to speak while using voice recognition Press the button on the steering wheel or the Phone button on the control panel and then select the Vehicle Phonebook key Select the Add New key at the top of the screen This will allow the user to add new phonebook content via the methods listed below Copy from Call History The system will show a list of your incoming outgoing or missed calls that were downloaded fr
435. stereo broadcast signal is weak the radio will automatically change from stereo to monaural reception TUNE FOLDER Tuning knob To manually tune the radio turn the TUNE FOLDER knob to the right or left 44 gt gt SEEK CAT and TRACK tuning buttons Press the SEEK CAT M4 button or the TRACK P button to tune from high to low or low to high frequencies and stop at the next broadcasting station SCAN tuning Press the SCAN button to stop at each broad casting station for 5 seconds Pressing the SCAN button again during this 5 second period will stop scan tuning and the radio will remain tuned to that station If the SCAN button is not pressed within 5 seconds scan tuning moves to the next station 1 to 6 Station memory operations Twelve stations can be set for the FM band 6 for FM1 6 for FM2 and six stations can be set for the AM band 1 Choose the radio band AM FM1 or FM2 using the AM FM select button 2 Tune to the desired station using manual SEEK or SCAN tuning Press and hold any of the desired station memory buttons 1 6 until a beep sound is heard 3 The channel indicator will then come on and the sound will resume Programming is now complete 4 Other buttons can be set in the same man ner If the battery cable is disconnected or if the fuse opens the radio memory will be canceled In that case reset the desired stations Monitor climate audio phone and voice recogniti
436. stolen NISSAN recommends erasing the ID code of that Intelli gent Key from the vehicle This may prevent the unauthorized use of the Intelligent Key to operate the vehicle For information regarding the erasing procedure contact a NISSAN dealer OPERATING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch 4 When the Intelligent Key battery is discharged or strong radio waves are present near the operat ing location the Intelligent Key operating range becomes narrower and the Intelligent Key may not function properly The operating range is within 31 50 in 80 cm from each request switch 4 If the Intelligent Key is too close to the door glass handle or rear bumper the request switches may not function When the Intelligent Key is within the operating range it is possible for anyone even someone who does not carry the Intelligent Key to push the request switch to lock unlock the doors DOOR LOCKS UNLOCKS PRECAUTION Do not push the door handle request switch with the Intelligent Key held in your hand as illustrated The close distance to the door handle will cause the Intelligent Key system to have difficulty recognizing that the Intelli gent Key is outside the vehicle After locking with the door handle request switch verify the doors are securely locked by testing them To prevent the Intelligent Key f
437. system AWARNING e ALWAYS give your full attention to driving Avoid using vehicle features that could distract you If distracted you could lose control of your vehicle and cause an accident Touch screen operation With this system the same operations as those Settings for the NISSAN controller are possible using the touch screen operation Adjust navigation settings Selecting the item Touch an item to select To select the Navigation key touch the Navigation key 1 on the screen Touch the BACK key Q2 to return to the previous screen Adjusting the item Touch the key or the key to adjust the settings of an item Touch the up arrow to scroll up the page one item at a time or touch the double up arrow to scroll up an entire page Touch the down arrow to scroll down the page one item at a time or touch the double down arrow to scroll down an entire page Uppercase Shows uppercase charactors ro werease Shows fowerease characters D E Fs Delete Deletes the last inputted character with one touch Touch and hold the Delete key to delete all of the characters ok Fe ites te creracterinpat Monitor climate audio phone and voice recognition systems 4 13 Touch screen maintenance If you clean the display screen use a dry soft cloth If additional cleaning is necessary use a small amount of neutral detergent with a soft cloth Never spray the screen with water or
438. t 2 Maintain a firm grip on the steering wheel with both hands and try to hold a straight course 3 When appropriate slowly release the accel erator pedal to gradually slow the vehicle 4 Gradually steer the vehicle to a safe location off the road and away from traffic if possible 5 Lightly apply the brake pedal to gradually stop the vehicle 6 Turn on the hazard warning flashers and either contact a roadside emergency service to change the tire or see Changing a flat tire in the In case of emergency section of this manual DRINKING ALCOHOL DRUGS AND DRIVING AWARNING Never drive under the influence of alcohol or drugs Alcohol in the bloodstream re duces coordination delays reaction time and impairs judgement Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others Additionally if you are injured in an accident alcohol can increase the severity of the injury NISSAN is committed to safe driving However you must choose not to drive under the influence of alcohol Every year thousands of people are injured or killed in alcohol related accidents Al though the local laws vary on what is considered to be legally intoxicated the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol Remember drinking and driving don t mix That is true for drugs too over the counter prescrip ti
439. t may result in a collision or injury e NEVER place a floor mat on top of an other floor mat in the driver front position e Use only genuine NISSAN floor mats specifically designed for use in your ve hicle model See your NISSAN dealer for more information Properly position the mats in the floor well using the floor mat positioning aid See Floor mat positioning aid in this section The use of genuine NISSAN floor mats can ex tend the life of your vehicle carpet and make it easier to clean the interior Mats should be main tained with regular cleaning and replaced if they become excessively worn Floor mat positioning aid This vehicle includes a front floor mat bracket to act as a floor mat positioning aid Genuine NISSAN floor mats have been specially designed for your vehicle model The driver s and passen ger s side floor mats have a grommet hole incor porated in them Position the mat by placing the floor mat bracket hook through the floor mat grommet hole while centering the mat in the floorwell Periodically check to make certain the mats are properly positioned Appearance and care 7 5 SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution Allow the belts to dry completely in the shade before using them See Seat belt maintenance in the Safety Seats seat belts and supplemen tal restraint system section of this manual AW
440. t all parts of the seat belt system for example buckles anchors adjusters and retractors operate properly and smoothly and are installed securely Check the belt web bing for cuts fraying wear or damage Steering wheel Check for changes in the steer ing system such as excessive freeplay hard steering or strange noises Warning lights and chimes Make sure all warning lights and chimes are operating properly Windshield wiper and washer Check that the wipers and washer operate properly and that the wipers do not streak Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner Under the hood and vehicle The maintenance items listed here should be checked periodically for example each time you check the engine oil or refuel Battery Check the fluid level in each cell It should be between the MAX and MIN lines Ve hicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level 8 4 Maintenance and do it yourself NOTE Care should be taken to avoid situations that can lead to potential battery discharge and potential no start conditions such as 1 Installation or extended use of electronic accessories that consume battery power when the engine is not running Phone char gers GPS DVD players etc 2 Vehicle is not driven regularly and or only driven s
441. t as necessary or put the restraint in another seat and test it again You may need to try a different child restraint Not all child restraints fit in all types of vehicles Safety Seats seat belts and supplemental restraint system 1 37 9 Check to make sure the child restraint is properly secured prior to each use If the seat belt is not locked repeat steps 3 through 8 LRSO865 Forward facing step 10 10 If the child restraint is installed in the front passenger seat place the ignition switch in the ON position The front passenger air bag status light should illuminate If this light is not illuminated see Front passenger air bag and status light in this section Move the child restraint to another seating position Have the system checked by a NISSAN dealer INSTALLING TOP TETHER STRAP First secure the child restraint with the LATCH lower anchors rear outboard seat positions only or the seat belt as applicable 1 Flip up the anchor cover T from the anchor point which is located directly behind the child seat 2 Position the top tether strap over the top of the head rest After the child restraint is removed and the seat belt is fully retracted the ALR mode child re straint mode is canceled 1 38 Safety Seats seat belts and supplemental restraint system Secure the tether strap to the tether anchor point on the rear parcel shelf 4 Refer to the appropriate child restraint
442. t belts The seat belt should be worn snug and always position the lap belt as low as possible around the hips not the waist Place the shoulder belt over your shoulder and across your chest Never run the lap shoulder belt over your ab dominal area Contact your doctor for specific recommendations INJURED PERSONS NISSAN recommends that injured persons use seat belts Check with your doctor for specific recommendations THREE POINT TYPE SEAT BELT WITH RETRACTOR AWARNING Every person who drives or rides in this vehicle should use a seat belt at all times e Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an accident you could be thrown into it and receive neck or other serious injuries You could also slide under the lap belt and receive serious internal injuries For the most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat with both feet on the floor and adjust the seat belt properly 1 18 Safety Seats seat belts and supplemental restraint system Do not allow children to play with the seat belts Most seating positions are equipped with Automatic Locking Re tractor ALR mode seat belts If the seat belt becomes wrapped around a child s neck with the ALR mode activated the child can be seriously injured or killed if the seat belt retracts and becomes
443. t is not occupied the passenger air bag is designed not to inflate in a crash However heavy objects placed on the seat could result in air bag inflation because of the object s weight detected by the occupant classification sensor Other conditions could also result in air bag inflation such as if a child is standing on the seat or if two children are on the seat contrary to the instructions in this manual Always be sure that you and all vehicle occupants are seated and restrained properly Using the passenger air bag status light you can monitor when the front passenger air bag Is au tomatically turned OFF with the seat occupied The light will not illuminate when the front pas senger seat is unoccupied If an adult occupant is in the seat but the passen ger air bag status light is illuminated indicating that the air bag is OFF it could be that the person is a small adult or is not sitting on the seat properly or not using the seat belt properly If a child restraint must be used in the front seat the passenger air bag status light may or may not be illuminated depending on the size of the child and the type of child restraint being used If the air bag status light is not illuminated indicating that the air bag might inflate in a crash it could be that the child restraint or seat belt is not being 1 52 Safety Seats seat belts and supplemental restraint system used properly Make sure that the child restraint is
444. tch is in the OFF position and the driver s door is opened After getting into the vehicle and placing the ignition switch in the ACC position the steering wheel moves to the previous position Slide Driver Seat Back on Exit Select to turn on or turn off the driver s seat moving backward for easy exit when the ignition switch is in the OFF position and the driver s door is opened After getting into the vehicle and placing the ignition switch in the ACC position the steering wheel moves to the previous position Return All Settings to Default Select to change all the comfort systems to their default settings nm tb Language Units Adjusts the language shown in the display Available settings are English Fran ais or Espa ol Adjusts the unit settings shown on the display Available settings are US mi F MPG and Metric km C L 100 km 41 gt OFF BUTTON night display The brightness can then be adjusted using the NISSAN controller To change the display brightness press the Xt D OFF button Pressing the button again The display brightness can also be adjusted us will change the display to the day or the nH ae nig ate ER G E AET button 4 10 Monitor climate audio phone and voice recognition systems If no operation is done within 10 seconds the display will return to the previous display Press and hold the 4 2 OFF button for more than 2 seconds to turn the display o
445. te the ve hicle tires to the recommended cold tire pressure indicated on the Tire and Loading Information label Trailer tire condition size load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturer s specifications Safety chains Always use suitable safety chains between your vehicle and the trailer The safety chains should be crossed and should be attached to the hitch not to the vehicle bumper or axle Be sure to leave enough slack in the chains to permit turning corners Trailer lights A CAUTION When splicing into the vehicle electrical system a commercially available power type module converter must be used to provide power for all trailer lighting This unit uses the vehicle battery as a direct power source for all trailer lights while using the vehicle tail light stoplight and turn signal circuits as a signal source The module converter must draw no more that 15 milliamps from the stop and tail lamp circuits Using a module converter that exceeds these power requirements may damage the vehicle s electrical system See a reputable trailer dealer to obtain the proper equipment and to have it installed Trailer lights should comply with federal and or local regulations For assistance in hooking up trailer lights contact a NISSAN dealer or repu table trailer dealer Trailer brakes If your trailer is equipped with a braking system make sure it conforms to
446. temperature con trol buttons Adjust the temperature display to about 75 F 24 C for normal operation The temperature of the passenger compart ment will be maintained automatically Air flow distribution and fan speed are also con trolled automatically A visible mist may be seen coming from the ventilators in hot humid conditions as the air is cooled rapidly This does not indicate a malfunction You can individually set driver s and front passenger s side temperature using each temperature control button When the DUAL button or passenger s side temperature but ton is pressed the DUAL indicator will come on To turn off the passenger s side tempera ture control press the DUAL button Heating A C OFF The air conditioner does not activate When you need to heat only use this mode 1 Press the A C button A C OFF will be displayed and A C indicator will turn off Operate the temperature control buttons to set the desired temperature The temperature of the passenger compart ment will be maintained automatically Air flow distribution and fan speed are also con trolled automatically 4 30 Monitor climate audio phone and voice recognition systems Do not set the temperature lower than the outside air temperature Otherwise the sys tem may not work properly Not recommended if windows fog up Dehumidified defrosting or defogging 1 Press the TY front defroster button on
447. ten tion may be given to vehicle operation Some jurisdictions prohibit the use of cellular phones while driving If you must make a call while your ve hicle is in motion the hands free cellu lar phone operational mode if so equipped is highly recommended Ex ercise extreme caution at all times so full attention may be given to vehicle operation If you are unable to devote full attention to vehicle operation while talking on the phone pull off the road to a safe location and stop your vehicle A CAUTION Keep the antenna as far away as pos sible from the electronic control modules Keep the antenna wire more than 8 in 20 cm away from the electronic control system harnesses Do not route the an tenna wire next to any harness Adjust the antenna standing wave ratio as recommended by the manufacturer Connect the ground wire from the CB radio chassis to the body For details consult a NISSAN dealer Monitor climate audio phone and voice recognition systems 4 91 BLUETOOTH HANDS FREE PHONE SYSTEM WITHOUT NAVIGATION SYSTEM if so equipped AWARNING e Use a phone after stopping your vehicle in a safe location If you have to use a phone while driving exercise extreme caution at all times so full attention may be given to vehicle operation If you are unable to devote full attention to vehicle operation while talking on the phone pull off the road to a safe location and stop your vehicle
448. tent Auto reverse function when closing or tilting down the moonroof The auto reverse function can be activated when the moonroof is closed or tilted down by auto matic operation when the ignition switch is placed in the ON position or for a period of time after the ignition switch is placed in the OFF position Depending on the environment or driving conditions the auto reverse func tion may be activated if an impact or load similar to something being caught in the moonroof occurs AWARNING There are some small distances immedi ately before the closed position which cannot be detected Make sure that all passengers have their hands etc inside the vehicle before closing the moonroof When closing If the control unit detects something caught in the moonroof as it moves to the front the moonroof will immediately open backward When tilting down If the control unit detects something caught in the moonroof as it tilts down the moonroof will im mediately tilt up If the auto reverse function malfunctions and re peats opening or tilting up the moonroof keep pushing the tilt down switch within 5 seconds after it happens the moonroof will fully close gradually Make sure nothing is caught in the moonroof AWARNING In an accident you could be thrown from the vehicle through an open moonroof Always use seat belts and child restraints e Do not allow anyone to stand up or extend any portion of their bod
449. teps to install a rear facing child restraint using the LATCH system 1 Position the child restraint on the seat Al ways follow the child restraint manufactur er s instructions WRS0801 WRS0802 Rear facing web mounted step 2 Rear facing rigid mounted step 2 Secure the child restraint anchor attach ments to the LATCH lower anchors Check to make sure the LATCH attachment is prop erly attached to the lower anchors LRS0673 Rear facing step 3 3 For child restraints that are equipped with webbing mounted attachments remove any additional slack from the anchor attach ments Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments Safety Seats seat belts and supplemental restraint system 1 29 5 Check to make sure the child restraint is properly secured prior to each use If the child restraint is loose repeat steps 1 through 4 LRS0674 nee eee REAR FACING CHILD RESTRAINT 4 After attaching the child restraint test it be fore you place the child in it Push it from side INSTALLATION USING THE SEAT to side while holding the child restraint near BELTS the LATCH attachment path The child re straint should not move more than 1 inch 25 mm from side to side Try to tug it forward and check to see if the LATCH at tachment holds the restraint in place If the
450. ter is level with the center of your ears If your ear position is still higher than the recommended alignment place the head restraint headrest at the highest position For non adjustable head restraint headrest Make sure the head restraint headrest Is posi tioned so the lock knob is engaged in the notch before riding in that designated seating position Safety Seats seat belts and supplemental restraint system 1 13 To raise the head restraint headrest To lower push and hold the lock knob pull it up and push the head restraint headrest down Make sure the head restraint headrest is posi tioned so the lock knob is engaged in the notch SRS l Make sure the head restraint headrest is posi before riding in that designated seating position tioned so the lock knob is engaged in the notch before riding in that designated seating position 1 14 Safety Seats seat belts and supplemental restraint system Front seat Active Head Restraints AWARNING e Always adjust the head restraints headrests properly as speci fied in this section Failure to do so can reduce the effectiveness of the Active Head Restraint Active Head Restraints are designed to supplement other safety systems Al ways wear seat belts No system can prevent all injuries in any accident e Do not attach anything to the head restraint headrest stalks Doing so could impair Active Head Restraint function The Active Head Restraint mo
451. ter in inches tires have this information 6 Two or three digit number 95 This 2 Three digit number 215 This num number is the tire s load index It is a ber gives the width in millimeters of measurement of how much weight the tire from sidewall edge to side each tire can support You may not wall edge find this information on all tires be 3 Two digit number 65 This number a a ay lan known as the aspect ratio gives the tire s ratio of height to width Maintenance and do it yourself 8 37 DOT XX XX XXX XXXX DOT t 1 XX XX t t 2 3 XXX t Example 3 4 2 TIN Tire Identification Number for a new tire example DOT XX XX XXX XXXX 1 DOT Abbreviation for the Depart ment Of Transportation The symbol can be placed above below or to the left or right of the Tire Identification Number 2 Two digit code identification mark Manufacturer s 8 38 Maintenance and do it yourself 4 XXX XXXX t t 5 6 WDI0396 Two digit code Tire size Three digit code Tire type code Optional Three digit code Date of Manufac ture Four numbers represent the week and year the tire was built For ex ample the numbers 3103 means the 31st week of 2003 If these numbers are missing then look on the other sidewall of the tire 3 Tire ply composition and material The number of layers or plies of rubber coated fabric in the tire Tire manufactur ers also must indi
452. tes the Push warning will illuminate if the ignition switch is placed in the ACC position when the shift lever is moved to the P Park position See Shift P warning in this section for additional information To turn off the Push warning place the ignition switch in the ON position and then to the LOCK position Low fuel warning This warning illuminates when the fuel level in the fuel tank is getting low Refuel as soon as it is convenient preferably before the fuel gauge reaches E Empty There will be a small re serve of fuel in the tank when the fuel gauge needle reaches E Empty 2 24 Instruments and controls Low windshield washer fluid warning This warning illuminates when the windshield washer fluid is at a low level Add windshield washer fluid as necessary See Windshield washer fluid in the Maintenance and do it yourself section of this manual No key warning This warning illuminates following two condi tions 1 When the ignition switch is pushed and the Intelligent Key cannot be recognized by the system If this warning illuminates you can not start the engine Check for the following causes and perform the assigned remedies The battery of the Intelligent Key carried with you is discharged completely Re place the battery with a new one The Intelligent Key carried with you is not registered to the system Use the regis tered Intelligent Key You do not
453. tes a dee teres aan ae ee 3 17 TOK ea 625 eet ge dances seca se eawen acess A 3 17 Opener operation 00 ccc eee eee eee 3 18 Interior trunk lid release 0 cee eee eee 3 19 Secondary trunk lid release if so equipped 3 19 Fuelle r door aces guneeseevs oeess Saget sdauecte ce 3 20 Opening the fuel filler door 0 eee eeae 3 20 PUCRINNIGr CdD 4 lt cccoretemedatesorueroseregaees 3 20 Tilt telescopic steering 0 00e eee eee eee 3 22 Manual operation if so equipped 3 23 Automatic operation if so equipped 3 23 DUN WiGOho 2 aticaviacceehee reuse urenes aneiuasncans 3 24 Vany MITOS ss2es cesers enoet ar Enea see 3 24 MITOS eea eran e EE E GA EEE 3 25 Automatic anti glare rearview mirror 3 25 OUSIDE MIMOS 224500 d20855 54 0neaes aed aee dees 3 27 Automatic drive positioner if so equipped 3 28 Memory storage function 0 cece ee eee 3 29 Eniry exit TUNCUON 232 ust accuseu se terisini 3 30 System operation s s snus aaua teatecasseetees 3 30 KEYS 1 Two Intelligent Keys 2 Mechanical keys with built in transpon der chip inside Intelligent Keys 3 Key number plate NISSAN INTELLIGENT KEY Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle s Intel ligent Key system components and NISSAN Ve hicle Immobilizer System components 3 2 Pre driving checks and adjus
454. the TUNE FOLDER knob or choose a folder displayed on the screen RPT RDM button When the RPT RDM button is pressed while the USB memory is playing the play pattern can be changed as follows Normal 1 Folder Repeat 1 Track Repeat All Random 1 Folder Random Normal USB gt Menu Menu There are some options available during play back Select one of the following that are dis played on the screen if necessary Refer to the following information for each item Movie Playback Switch to the movie playback mode This item is displayed only when the USB memory contains movie files The shift lever must be in Park P with the parking brake engaged to watch movies from a USB device Monitor climate audio phone and voice recognition systems 4 77 Folder List Track List Displays the folder or track list The Movie Playback key is also displayed in this list screen and enables you to switch to the movie playback mode Play Mode Choose the preferred play mode using the NISSAN controller or the touchscreen Movie file operation Park the vehicle in a safe location for the front seat occupants to operate the USB memory while watching the images DISC AUX button When the DISC AUX button is pushed with the system off and the USB memory inserted the system will turn on If another audio source is playing and the USB memory is inserted press the DISC AUX button repeatedly until the c
455. the command the system will prompt you to speak the number Redial Use the Redial command to call the last number that was dialed The system acknowledges the command re peats the number and begins dialing If a redial number does not exist the system announces There is no number to redial and ends the VR session Call Back Use the Call Back command to dial the number of the last incoming call within the vehicle The system acknowledges the command re peats the number and begins dialing If a call back number does not exist the system announces There is no number to call back and ends the VR session During a call During a call there are several command options available Press the i button on the steering wheel to mute the receiving voice and enter com mands Help The system announces the avail able commands Go back Correction The system an nounces Go back ends the VR session and returns to the call Cancel Quit The system announces Cancel ends the VR session and returns to the call Send Enter Call Dial Use the Send command to enter numbers or during a call For example if you were directed to dial an extension by an automated system Say Send one two three four The system acknowledges the command and sends the tones associated with the numbers The system then ends the VR ses
456. the engine coolant The service procedure can be found in the NISSAN Service Manual Improper servicing can result in reduced heater performance and engine overheat ing AWARNING To avoid the danger of being scalded never change the coolant when the en gine is hot e Never remove the radiator cap when the engine is hot Serious burns could be caused by high pressure fluid escaping from the radiator Avoid direct skin contact with used coolant If skin contact is made wash thoroughly with soap or hand cleaner as soon as possible Keep coolant out of the reach of chil dren and pets Engine coolant must be disposed of properly Check your local regulations Maintenance and do it yourself 8 9 ENGINE OIL CHECKING ENGINE OIL LEVEL 1 Park the vehicle on a level surface and apply the parking brake Start the engine and let it idle until it reaches operating temperature Turn off the engine Wait more than 10 minutes for the oil to drain back into the oil pan Remove the dipstick and wipe it clean Re insert it all the way 8 10 Maintenance and do it yourself DCA atata a 5 Remove the dipstick again and check the oil level It should be between the H High and L Low marks This is the normal oper ating oil level range If the oil level is below the L Low mark remove the oil filler cap and pour recommended oil through the opening Do not overfill 6 Recheck oil
457. the road surface based on vehicle road or traffic conditions gradually slow the vehicle to a stop in a safe place off the road RAPID AIR PRESSURE LOSS Rapid air pressure loss or a blow out can occur if the tire is punctured or is damaged due to hitting a curb or pothole Rapid air pressure loss can also be caused by driving on under inflated tires Rapid air pressure loss can affect the handling and stability of the vehicle especially at highway speeds Help prevent rapid air pressure loss by maintain ing the correct air pressure and visually inspect the tires for wear and damage See Wheels and tires in the Maintenance and do it yourself section of this manual If a tire rapidly loses air pressure or blows out while driving maintain control of the vehicle by following the procedure below Please note that this procedure is only a general guide The vehicle must be driven as appropriate based on the conditions of the ve hicle road and traffic AWARNING The following actions can increase the chance of losing control of the vehicle if there is a sudden loss of tire air pressure Losing control of the vehicle may cause a collision and result in personal injury The vehicle generally moves or pulls in the direction of the flat tire e Do not rapidly apply the brakes Do not rapidly release the accelerator pedal Do not rapidly turn the steering wheel 1 Remain calm and do not overreac
458. the seat seat belt and child restraints is necessary for most effective protection Failure to follow all instructions in this manual con cerning the use of seats seat belts and child restraints can increase the risk or severity of injury in an accident Status light The front passenger air bag status light fe is located above the radio After the ignition switch is placed in the ON position the front passen ger air bag status light on the instrument panel illuminates for about 7 seconds and then turns off or remains illuminated depending on the front passenger seat occupied status The light oper ates as follows s Unoccupied passenger s seat The Ais OFF and the front passenger air bag is OFF and will not inflate in a crash Passenger s seat occupied by a small adult child or child restraint as outlined in this section The illuminates to indicate that the front passenger air bag is OFF and will not inflate in a crash Occupied passenger seat and the passenger meets the conditions outlined in this section The light 2 is OFF to indicate that the front passenger air bag is operational Front passenger air bag The front passenger air bag is designed to auto matically turn OFF when the vehicle is operated under some conditions as described below in accordance with U S regulations If the front passenger air bag is OFF it will not inflate in a crash The driver air bag and other air bags in your v
459. the solutions are listed by number try each solution in turn starting with number one until the problem is resolved Displays COMMAND NOT RECOG Ensure that the command format is valid see Standard Mode command list or Alternate Command Mode command list in this NIZED or the system fails to interpret section the command correctly Speak clearly using your normal speech pattern and at a level appropriate to the ambient noise level Ensure that the ambient noise level is not excessive for example windows open or defrost on NOTE If it is too noisy to use the phone it is likely that voice commands will not be recognized Ensure that the voicetag requested matches what was originally stored See Bluetooth Hands Free Phone System with Navigation wrong voicetag in the phonebook System in this section 2 Replace one of the voicetags being confused with a different voicetag The system consistently selects the We 4 136 Monitor climate audio phone and voice recognition systems 5 Starting and driving Precautions when starting and driving 5 2 Exhaust gas carbon monoxide 0008 5 2 Three way catalyst ns oe ued eden ewenteeuen anes 5 2 Tire Pressure Monitoring System TPMS 5 3 Avoiding collision and rollover 0005 5 5 Off road TECOVENY lt ices pekedtenkedahacadtewa ges 5 6 Rapid air pressure lOSS 0 cece eee ees 5 6 Drinking alcohol dru
460. the warnings and instruc tions for proper use and installation of child restraints could result in serious in jury or death of a child or other passen gers in a sudden stop or collision Attach LATCH system compatible child restraints only at the locations shown in the illustration Do not secure a child restraint in the center rear seating position using the LATCH lower anchors The child re straint will not be secured properly Inspect the lower anchors by insert ing your fingers into the lower anchor area Feel to make sure there are no obstructions over the anchors such as seat belt webbing or seat cushion material The child restraint will not be secured properly if the lower an chors are obstructed Child restraint anchorages are de signed to withstand only those loads imposed by correctly fitted child re straints Under no circumstances are they to be used to attach adult seat belts or other items or equipment to the vehicle Doing so could damage the child restraint anchorages The child restraint will not be properly installed using the damaged anchor age and a child could be seriously injured or killed in a collision WRS0700 LATCH lower anchor location LATCH lower anchor location The LATCH lower anchors are located at the rear of the seat cushion near the seatback A label is attached to the seatback to help you locate the LATCH lower anchors LRS0661 LATCH webbing mounted attachm
461. times to skip back through tracks The compact disc will go back the number of times the button is pressed When the TRACK PP button is pressed while the compact disc is playing the next track will start to play from its beginning Press several times to skip through tracks The compact disc will advance the number of times the button is pressed When the last track on the compact disc is skipped through the first track will be played 44 gt SEEK CAT and TRACK Rewind Fast Forward buttons Press and hold the SEEK CAT M4 rewind button or the TRACK PPI fast forward button while a compact disc Is playing the compact disc 4 54 Monitor climate audio phone and voice recognition systems will play while rewinding or fast forwarding When the button is released the compact disc will return to normal play speed TUNE FOLDER knob While playing an MP3 WMA CD turn the TUNE FOLDER knob right or left to scan forward or backward through available folders CD select buttons To play another CD that has been loaded press a CD select button 1 6 RPT RDM button When the RPT RDM button is pressed while the compact disc is playing the play pattern can be changed as follows CD All Disc Repeat 1 Disc Repeat 1 Track Repeat All Disc Random 1 Disc Random All Disc Repeat MP3 WMA CD All Disc Repeat 1 Disc Repeat 1 Folder Repeat 1 Track Repeat All Disc Random 1
462. tion 2 Using both hands simultaneously press and hold the desired HomeLink button and the hand held transmitter button During train ing your hand held transmitter may auto matically stop transmitting Continue to Instruments and controls 2 55 press and hold the desired HomeLink but ton while you press and re press cycle your hand held transmitter every two sec onds until the frequency signal has been learned The HomeLink indicator light will flash slowly and then rapidly after several seconds upon successful training DO NOT release until the HomeLink indicator light flashes slowly and then rapidly When the indicator light flashes rapidly both buttons may be released The rapid flashing indi cates successful training Proceed with Programming HomeLink step 3 to complete If the device was unplugged during the pro gramming procedure remember to plug it back in when programming is completed OPERATING THE HOMELINK UNIVERSAL TRANSCEIVER The HomeLink Universal Transceiver after it is programmed can be used to activate the pro grammed device To operate simply press and release the appropriate programmed HomeLink Universal Transceiver button The amber indicator light will illuminate while the sig nal is being transmitted For convenience the hand held transmitter of the device may also be used at any time 2 56 Instruments and controls PROGRAMMING TROUBLE DIAGNOSIS If the
463. tion within a few seconds NOTE Use zone number 5 for Hawaii Inaccurate compass direction The compass display is equipped with automatic correction function If the correct direction is not shown follow this procedure 1 With the display turned on press and hold t the N for about 10 seconds The C icon in the compass display will illuminate 2 Calibrate the compass by driving the vehicle in three complete circles at a maximum speed of 5 MPH 8 km h 3 After completing the circles the display should return to normal A CAUTION Do not install a ski rack antenna etc which are attached to the vehicle by means of a magnet They affect the op eration of the compass When cleaning the mirror use a paper towel or similar material dampened with glass cleaner Do not spray glass cleaner directly on the mirror as it may cause the liquid cleaner to enter the mirror housing Instruments and controls 2 9 WARNING INDICATOR LIGHTS AND AUDIBLE REMINDERS ABS or Anti lock Braking System ABS warning light BRAKE or Brake warning light Charge warning light Engine oil pressure warning light Low tire pressure warning light Master warning light Seat belt warning light and chime CHECKING BULBS With all doors closed apply the parking brake and place the ignition switch in the ON position without starting the engine The following lights will come on FA eae or a BF A A
464. tments MANUAL OPERATION if so equipped Tilt and telescopic operation Pull the lock lever all the way towards you wheel forward or back to the desired position Adjust the steerin ward in direction Adjust the steering wheel up or down in direction 3 to the desired position Lock the steering wheel by releasing the lock lever Make sure the lock lever has returned to its original position to lock the steering wheel in place AUTOMATIC OPERATION if so equipped Tilt operation Push the switch up or down to adjust the steering wheel to the desired position Telescopic operation Push the switch forward or backward to ad just the steering wheel to the desired position Pre driving checks and adjustments Entry Exit function The automatic drive positioner system will make the steering wheel move up automatically when the driver s door is opened and the ignition switch is in the LOCK position This lets the driver get into and out of the seat more easily The steering wheel moves back into position when the driver s door is closed and the ignition switch is pushed For more information see Automatic drive posi tioner in this section 3 23 SUN VISORS 3 24 Pre driving checks and adjustments To block glare from the front swing down the sun visor 2 To block glare from the side remove the sun visor from the center mount and swing the visor to the side 3 Slide
465. tments Never leave these keys in the vehicle As many as 4 Intelligent Keys can be registered and used with one vehicle The new keys must be registered by a NISSAN dealer prior to use with the Intelligent Key system and NISSAN Vehicle Immobilizer System of your vehicle Since the registration process requires erasing all memory in the Intelligent Key components when register ing new keys be sure to take all Intelligent Keys that you have to the NISSAN dealer A key number plate is supplied with your keys Record the key number and keep it in a safe place such as your wallet not in the vehicle If you lose your keys see a NISSAN dealer for duplicates by using the key number NISSAN does not record key numbers so it is very important to keep track of your key number plate A key number is only necessary when you have lost all keys and do not have one to duplicate from If you still have a key your NISSAN dealer can duplicate it A CAUTION Listed below are conditions or occur rences which will damage the Intelligent Key Do not allow the Intelligent Key which contains electrical components to come into contact with water or salt water This could affect the system function Do not drop the Intelligent Key Do not strike the Intelligent Key sharply against another object Do not change or modify the Intelligent Key Wetting may damage the Intelligent Key If the Intelligent Key gets wet im mediately wipe unt
466. to a suitable body ground such as the frame or engine block area DRIVE BELT Power steering fluid pump Generator Air conditioner compressor Crankshaft pulley a a AWARNING Be sure the ignition switch is in the OFF or LOCK position before servicing drive belt The engine could rotate unexpectedly 1 Visually inspect the belt for signs of unusual wear Cuts fraying or looseness If the belt is in poor condition or is loose have it replaced or adjusted by a NISSAN dealer Maintenance and do it yourself 8 17 2 Have the belt checked regularly for condi tion and tension in accordance with the maintenance schedule found in the NISSAN Service and Maintenance Guide 8 18 Maintenance and do it yourself SPARK PLUGS REPLACING SPARK PLUGS lridium tipped spark plugs It is not necessary to replace iridium tipped spark plugs as frequently as conventional type spark plugs because they last much longer Fol low the maintenance log shown in the NISSAN Service and Maintenance Guide Do not service iridium tipped spark plugs by cleaning or regap ping e Always replace spark plugs with rec ommended or equivalent ones AWARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely A CAUTION Be sure to use the correct socket to re move the spark plugs An incorrect socket can damage the spark plugs If replacement is required see your NISSAN dealer
467. to jump start a frozen battery It could explode and cause se rious injury Your vehicle has an automatic engine cooling fan It could come on at any time Keep hands and other objects away from it Vehicle eee started eS y A WARNING k Always follow the instructions below Fail ure to do so could result in damage to the charging system and cause personal 4 injury 1 If the booster battery is in another vehicle position the two vehicles to bring their bat teries near each other Vehicle with AA battery for Cloth booster WCE0054 Remove the vent caps on the battery if so equipped Cover the battery with an old cloth to reduce explosion hazard Connect the jumper cables in the sequence illustrated A CAUTION e Always connect positive to positive and negative to body ground for Do not allow the two vehicles to touch example strut mounting bolt engine 2 Apply the parking brake Move the shift lever to P Park Switch off all unnecessary elec trical systems lights heater air conditioner etc lift bracket etc not to the battery Make sure the jumper cables do not touch moving parts in the engine com partment and that the cable clamps do not contact any other metal 5 Start the engine of the booster vehicle and let it run for a few minutes 6 Keep the engine speed of the booster ve hicle at about 2 000 rpm and start the en gine of the v
468. too high When the ve hicle speed decreases the transmis sion automatically shifts down and shifts to 1st gear before the vehicle comes to a stop CVT operation is limited to automatic drive mode when CVT fluid temperature is ex tremely low even if manual shift mode is selected This is not a malfunction When CVT fluid warms up manual mode can be selected When the CVT fluid temperature is high the shift range may upshift in lower rom than usual This is not a malfunction Shift lock release If the battery charge is low or discharged the shift lever may not be moved from the P Park position even with the brake pedal depressed and the shift lever button pressed It will be necessary to jump start or have your battery charged see Jump starting in the In case of emergency section Contact your NISSAN dealer or a professional towing service To move the shift lever complete the following procedure 1 Press the ignition switch to the LOCK posi tion 2 Apply the parking brake 3 Using a protective cloth on the tip of a3 mm screwdriver remove the shift lock release cover f available a plastic trim tool can also be used 4 Insert the small screwdriver in the shift lock release slot and push down 5 Move the shift lever to the N Neutral posi tion while holding down the shift lock re lease 6 Push the ignition switch to the ON position to unlock the steering wheel Now
469. toward c gt 2 46 instruments and controls To open or close the moonroof part way push the switch in any direction while the moonroof is sliding to stop it in the desired position Tilting the moonroof Close the moonroof by pushing the switch toward lt 2 Release the switch then push the switch toward gt again to tilt the moonroof up To tilt the moonroof down push the switch toward gt A A WARNING In an accident you could be thrown from the vehicle through an open moonroof Always use seat belts and child restraints e Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing A CAUTION e Remove water drops snow ice or sand from the moonroof before opening Do not place heavy objects on the moonroof or surrounding area Auto reverse function when closing or tilting down the moonroof The auto reverse function can be activated when the moonroof is closed or tilted down by auto matic operation when the ignition switch is placed in the ON position or for a period of time after the ignition switch is placed in the OFF position Depending on the environment or driving conditions the auto reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs AWARNING There are some small distances immedi ately before the clo
470. trol VDC off indicator light in the Instru ments and controls section If a malfunction occurs in the system the ft indicator light comes on in the instrument panel The VDC system automatically turns off when the indicator light is off The VDC OFF switch is used to turn off the VDC system The indicator illuminates to indi cate the VDC system is off When the VDC switch is used to turn off the system the VDC system still operates to prevent one drive wheel from slipping by transferring power to a non slipping drive wheel The indicator flashes if this occurs All other VDC functions are off and the ft indicator will not flash The VDC system is automatically reset to on when the ignition switch is placed in the off position then back to the on position The computer has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle forward or in reverse at a slow speed When the self test occurs you may hear a clunk noise and or feel a pulsation in the brake pedal This is normal and is not an indication of a malfunction AWARNING The VDC system is designed to help the driver maintain stability but does not prevent accidents due to abrupt steer ing operation at high speeds or by care less or dangerous driving techniques Reduce vehicle speed and be especially careful when driving and cornering on slippery surfaces and always drive carefully e Do not modify
471. ts When checking the tires make sure no wheel nuts are missing and check for any loose wheel nuts Tighten if necessary Tire rotation Tires should be rotated every 5 000 miles 8 000 km Tires Check the pressure with a gauge often and always prior to long distance trips If neces sary adjust the pressure in all tires including the spare to the pressure specified Check carefully for damage cuts or excessive wear Tire Pressure Monitoring System TPMS transmitter components Replace the TPMS transmitter grommet seal valve core and cap when the tires are replaced due to wear or age Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road or if you detect uneven or abnormal tire wear there may be a need for wheel alignment If the steering wheel or seat vibrates at normal highway speeds wheel balancing may be needed For additional information regarding tires refer to Important Tire Safety Information US or Tire Safety Information Canada in the Warranty Information Booklet Windshield Clean the windshield on a regular basis Check the windshield at least every six months for cracks or other damage Have a dam aged windshield repaired by a qualified repair facility Windshield wiper blades Check for cracks or wear if they do not wipe properly Inside the vehicle The maintenance items listed here should be checked on a regular basis
472. ttery discharge and potential no start conditions such as 1 Installation or extended use of electronic accessories that consume battery power when the engine is not running Phone char gers GPS DVD players etc 2 Vehicle is not driven regularly and or only driven short distances In these cases the battery may need to be charged to maintain battery health A WARNING e Do not expose the battery to flames an electrical spark or a cigarette Hydrogen gas generated by the battery is explo sive Explosive gases can cause blind ness or injury Do not allow battery fluid to contact your skin eyes fabrics or painted surfaces Sulfuric acid can cause blindness or injury After touch ing a battery or battery cap do not touch or rub your eyes Thoroughly wash your hands If the acid contacts your eyes skin or clothing immediately flush with water for at least 15 minutes and seek medical attention Do not operate the vehicle if the fluid in the battery is low Low battery fluid can cause a higher load on the battery which can generate heat reduce battery life and in some cases lead to an explosion When working on or near a battery al ways wear suitable eye protection and remove all jewelry Battery posts terminals and related ac cessories contain lead and lead com pounds Wash hands after handling e Keep battery out of the reach of children Do not tip the battery Keep the vent caps tight an
473. tuning to adjust and then press the AUDIO button until the display returns to the main audio screen If the button is not pressed for approximately 10 seconds the radio or CD display will automatically reappear Clock set The clock displays the time when the ignition switch is placed in the ACC or ON position Adjusting the time 1 Push and hold the DISP CLOCK button for more than 2 seconds until the display shows Hour Adjust 2 Turn the TUNE FOLDER knob to adjust the hour 3 Press the DISP CLOCK button again the display will show Minute Adjust 4 Turn the TUNE FOLDER knob to adjust the minutes 5 Press the DISP CLOCK button again to exit the clock set mode Press the DISP CLOCK button again to return to the regular clock display If no action is taken the display will return to the regular clock display after 10 seconds If the power supply is disconnected the clock will not indicate the correct time Readjust the time 4 52 Monitor climate audio phone and voice recognition systems CD display mode To change the text displayed while playing a CD with text press the DISP CLOCK button The DISP CLOCK button will allow you to scroll through CD text as follows Track number and Track time Album title Song title Track number displays the track number se lected on the disc Track time displays the amount of time the track has played Album title displays the title of the
474. uctions are avail able from a NISSAN dealer Local service opera tors are generally familiar with the applicable laws and procedures for towing To assure proper towing and to prevent accidental damage to your vehicle NISSAN recommends having a service operator tow your vehicle It is advisable to have the service operator carefully read the following precautions AWARNING Never ride in a vehicle that is being towed Never get under your vehicle after it has been lifted by a tow truck A CAUTION When towing make sure that the trans mission axles steering system and powertrain are in working condition If any of these conditions apply dollies or a flatbed tow truck must be used Always attach safety chains before towing For information about towing your vehicle behind a recreational vehicle RV refer to Flat towing in the Technical and consumer information sec tion of this manual TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving front wheels off the ground or place the vehicle on a flat bed truck as illustrated In case of emergency 6 11 6 12 In case of emergency A CAUTION Never tow CVT models with the front wheels on the ground or four wheels on the ground forward or backward as this may cause serious and expensive damage to the transmission If it is nec essary to tow the vehicle with the rear wheels raised always use t
475. until a single click is heard Pre driving checks and adjustments 3 21 TILT TELESCOPIC STEERING 3 Press the O next button A on the in AWARNING strument panel located behind the steering tio LOOSE wheel for about 1 second to turn off the Do not adjust the steering wheel while oap LOOSE FUEL CAP warning after tight driving You could lose control of your ening the fuel filler cap vehicle and cause an accident e Do not adjust the steering wheel any closer to you than is necessary for proper steering Operation and comfort The driver s air bag inflates with great force If you are unrestrained leaning forward sitting sideways or out of posi tion in any way you are at greater risk of injury or death in a crash You may also receive serious or fatal injuries from the air bag if you are up against it when it Loose Fuel Cap warning inflates Always sit back against the seatback and as far away as practical The LOOSE FUEL CAP warning appears in the from the steering wheel Always use the vehicle information display when the fuel filler seat belts cap is not tightened correctly after the vehicle has been refueled It may take a few driving trips for the message to be displayed To turn off the warning perform the following 1 Remove and install the fuel filler cap as soon as possible See Fuel filler cap in this sec tion 2 Tighten the fuel filler cap until it clicks 3 22 Pre driving checks and adjus
476. ure if so equipped The reverse tilt down feature will turn both out side mirror surfaces downward to provide better rear visibility close to the vehicle when the small switch is in either the L or R position Pre driving checks and adjustments 3 27 NOTE If the outside mirror control switch is in the neutral position neither mirror will turn downward when the shift lever is moved to R Reverse Move the shift lever to R Reverse Both mirrors will turn downward The mirror surfaces will return to their original position when any of the following have occurred The shift lever is moved to any position other than R Reverse The outside mirror control switch is set to the neutral or center position The ignition switch is placed in the OFF position 3 28 Pre driving checks and adjustments Foldable outside mirrors Pull the outside mirror toward the door to fold tt Heated mirrors if so equipped The electric control type outside mirrors can be heated to defrost defog or de ice for improved visibility Push the rear window defogger switch to activate the heating function Push the switch again to deactivate or the heating function will automatically turn off after approximately 15 min utes AUTOMATIC DRIVE POSITIONER if so equipped The automatic drive positioner system has two features Memory storage function Entry exit function MEMORY STORAGE FUNCTION Two positions for the
477. us injury or death of a child or other passengers in a sudden stop or collision The child restraint must be used and installed properly Always follow all of the child restraint manufacturer s instructions for installation and use Infants and children should never be held on anyone s lap Even the stron gest adult cannot resist the forces of a collision Do not put a seat belt around both a child and another passenger NISSAN recommends that all child restraints be installed in the rear seat Studies show that children are safer when properly restrained in the rear seat than in the front seat If you must install a forward facing child restraint in the front seat see Forward facing child restraint in stallation using the seat belts later in this section Even with the NISSAN Advanced Air Bag System never install a rear facing child restraint in the front seat An inflating air bag could seriously injure or kill a child A rear facing child restraint must only be used in the rear seat Be sure to purchase a child restraint that will fit the child and vehicle Some child restraints may not fit properly in your vehicle Child restraint anchor points are de signed to withstand loads from child restraints that are properly fitted Never use the anchor points for adult seat belts or harnesses A child restraint with a top tether strap should not be used in the front pass
478. usts the time zone Choose a time zone form the available list Monitor climate audio phone and voice recognition systems 4 17 Select the Others key using the NISSAN controller Voice Recognition language and units setting screen will be displayed Comfort Select the Others key using the NISSAN controller then select the Comfort key The Comfort settings screen will be displayed You can set the following operating conditions by selecting the desired item using the NISSAN controller The indicator light box at the right of the selected item alternately turns on and off each time the item is touched or the ENTER button is pressed Indicator light is illuminated ON Indicator light is not illuminated OFF Auto Interior Illumi Select to turn on or off the illumination of the interior lights when any door is unlocked nation Light Sensitivity Select to adjust the sensitivity of the automatic headlights higher right or lower left After selecting the item turn the NISSAN controller or touch the or key to change the setting Light Off Delay Select to change the duration of the automatic headlight off timer After selecting the item turn the NISSAN controller or touch the or key to change the setting The available delays are O 30 45 60 90 120 150 and 180 seconds Speed Sensing Select to turn on or turn off the wiper interval adjusted automatically according to the vehicle speed
479. utboard seating positions in certain side impact collisions The curtain air bags are designed to inflate on the side where the vehicle is impacted These supplemental restraint systems are de signed to supplement the crash protection pro vided by the driver and front passenger seat belts and are not a substitute for them Seat belts should always be correctly worn and the occu pant seated a suitable distance away from the steering wheel instrument panel and door finish ers See Seat belts earlier in this section for instructions and precautions on seat belt usage The supplemental air bags operate only when the ignition switch is in the ON or START position After placing the ignition switch in the ON position the supplemental air bag warning light illuminates The supplemental air bag warning light will turn off after about 7 sec onds if the system is operational AWARNING The front air bags ordinarily will not inflate in the event of a side impact rear impact rollover or lower severity fron tal collision Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents The front passenger air bag will not inflate if the passenger air bag status light is lit or if the front passenger seat is unoccupied See Front passenger air bag and status light later in this section The seat belts and the front air bags are most effective when you are sitting w
480. utside mirror on the passenger side are closer than they appear Be careful when moving to the right Using only this mirror could cause an accident Use the inside mirror or glance over your shoulder to properly judge distances to other objects e Do not adjust the mirrors while driving You could lose control of your vehicle and cause an accident Automatic anti glare outside mirror Driver s side only if so equipped The driver s outside mirror will automatically dim during nighttime conditions to reduce the glare from the headlights of trailing vehicles The auto matic anti glare feature operates only when the ignition switch is placed in the ON position The automatic anti glare feature will be on when starting the vehicle The indicator light on the automatic anti glare rearview mirror will illuminate when the automatic anti glare feature Is on To turn off the automatic anti glare feature press the O button on rearview mirror without compass Type B the button on rearview mirror with compass Type The indicator light will turn off To turn on the automatic anti glare feature again press the button on rearview mirror without compass Type B the button on rearview mirror equipped with compass Type The indicator light will turn on For information on the automatic anti glare rear view mirror see Automatic anti glare rearview mirror in this section Reverse tilt down feat
481. uttons 2 cer tain Navigation System functions use the addi tional directional buttons or the center dial 3 Then press the ENTER button 4 to select the item or perform the action The BACK button 4 has two functions Go back to the previous display cancel If you press the BACK button during setup the setup will be canceled and or the display will return to the previous screen Finish setup In some screens pressing the BACK button 4 accepts the changes made during setup For the VOICE button 8 functions refer to the separate Navigation System Owner s Manual HOW TO USE THE TOUCH SCREEN A CAUTION The glass display screen may break if it is hit with a hard or sharp object If the glass screen breaks do not touch it Doing so could result in an injury To clean the display never use a rough cloth alcohol benzine thinner or any kind of solvent or paper towel with a chemical cleaning agent They will scratch or deteriorate the panel e Do not splash any liquid such as water or car fragrance on the display Contact with liquid will cause the system to malfunction 4 12 Monitor climate audio phone and voice recognition systems To help ensure safe driving some functions can not be operated while driving The on screen functions that are not available while driving will be grayed out or muted Park the vehicle in a safe location and then oper ate the navigation
482. ve poor traction performance 9 24 Technical and consumer information AWARNING The traction grade assigned to this tire is based on straight ahead braking traction tests and does not include acceleration cornering hydroplaning or peak traction characteristics Temperature A B and C The temperature grades are A the highest B and C representing the tire s resistance to the genera tion of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sustained high tem perature can cause the material of the tire to de generate and reduce tire life and excessive tem perature can lead to sudden tire failure The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No 109 Grades B and A represent higher levels of performance on the labo ratory test wheel than the minimum required by law AWARNING The temperature grade for this tire is estab lished for a tire that is properly inflated and not overloaded Excessive speed under inflation or excessive loading either sepa rately or in combination can cause heat build up and possible tire failure EMISSION CONTROL SYSTEM WARRANTY Your NISSAN vehicle is covered by the following emission warranties For USA 1 Emission Defects Warranty 2 Emissions Performance Warranty Details of this warranty may be found with other vehi
483. ver Move the lever up or down manual or move the switch forward or backward power to adjust the seat lumbar area 1 4 Safety Seats seat belts and supplemental restraint system Power if so equipped LRS2192 LRS0863 Thigh extension driver s side only if SO equipped Pull up and hold the lever to extend the front portion to the desired position FOLDING REAR SEAT if so equipped Interior trunk access For models without a rear center console the trunk can be accessed from the passenger side of the rear seat for loading and unloading as shown Q Press down on the button on the rear parcel shelf 2 Fold down the passenger side seatback AWARNING Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold down position Use of these areas by passengers without proper restraints could result in serious injury in an acci dent or sudden stop Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting Do not place cargo higher than the seatbacks In a sudden stop or col lision unsecured cargo could cause personal injury Safety Seats seat belts and supplemental restraint system 1 5 When returning the seatbacks to the upright position be certain they are completely secured in the latched posi tion If they are not completely secured passengers may be injured in an acci dent or sudden stop Closely supervise
484. ves forward utiliz ing the force that the seatback receives from the occupant in a rear end collision The movement of the head restraint headrest helps support the occupant s head by reducing its backward move ment and helping absorb some of the forces that may lead to whiplash type injuries Active Head Restraints are effective for collisions at low to medium speeds in which it is said that whiplash injuries occur most Active Head Restraints operate only in certain rear end collisions After the collision the head restraint headrests return to their original posi tions Properly adjust the Active Head Restraints as described earlier in this section SEAT BELTS Lf yf Sit upright and well back PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly ad justed and you are sitting upright and well back in your seat with both feet on the floor your chances of being injured or killed in an accident and or the severity of injury may be greatly reduced NISSAN strongly encourages you and all of your passengers to buckle up every time you drive even if your seating position includes a supple mental air bag Most U S states and Canadian provinces or territories specify that seat belts be worn at all times when a vehicle is being driven Safety Seats seat belts and supplemental restraint system 1 15 LO ie Sit upright and weil back AWARNING
485. volume of the audio system as the speed of the vehicle increases Set to OFF to disable the feature The higher the setting the more the volume increases in relation to vehicle speed Displays the DivX registration code on the screen Toggles on or off the display of the CD jacket art when available if a CD is playing Bass treble balance and fade can also be adjusted by pressing the AUDIO control knob and turning it to select the item to adjust When the desired item is shown on the display turn the tuning to adjust and then press the AUDIO button until the display returns to the main audio screen If the button is not pressed for approximately 10 seconds the radio or CD display will automatically reappear 4 64 Monitor climate audio phone and voice recognition systems Settings gt Audio 8 00 Display album cover art When an audio source encoded with album cover art is played the album cover art can be displayed on the screen To toggle this feature on or off touch the Display Album Cover Art key When the feature is activated the amber indica tor next to the word ON will illuminate Artist XXXAXXXXX Album XXXXAXXX Track XXXXXXXX Folder Track CD DVD or USB with compressed audio files While listening to a CD or compressed audio files certain text might be able to be displayed when CD encoded with text is being used Depending on how the CD or compressed audio files are encoded the followin
486. w the driver and passengers some freedom of movement in the seat The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts The Automatic Locking Retractor ALR mode child restraint mode locks the seat belt for child restraint installation When the ALR mode is activated the seat belt cannot be extended again until the seat belt tongue is detached from the buckle and fully retracted The seat belt returns to the ELR mode after the seat belt fully retracts See Child re straints later in this section for more information The ALR mode should be used only for child restraint installation During normal seat belt use by an occupant the ALR mode should not be activated If it is activated it may cause uncomfortable seat belt ten sion AWARNING When fastening the seat belts be certain that the seatbacks are completely secured in the latched position If they are not completely secured passengers may be injured in an accident or sudden stop 1 20 Safety Seats seat belts and supplemental restraint system Unfastening the seat belts 1 To unfasten the seat belt press the button on the buckle The seat belt automatically re tracts Checking seat belt operation Seat belt retractors are designed to lock seat belt movement by two separate methods When the seat belt is pulled quickly from the retractor When the vehicle slows down rapidly To increase your confidenc
487. ward facing child restraints are available for children who outgrow rear facing child restraints and are at least 1 year old Booster seats are used to help position a vehicle lap shoulder belt on a child who can no longer use a forward facing child restraint AWARNING Infants and children need special protec tion The vehicle s seat belts may not fit them properly The shoulder belt may come too close to the face or neck The lap belt may not fit over their small hip bones In an accident an improperly fitting seat belt could cause serious or fatal injury Always use appropriate child restraints All U S states and Canadian provinces or territo ries require the use of approved child restraints for infants and small children See Child re straints later in this section A child restraint may be secured in the vehicle by using either the LATCH Lower Anchor and Teth ers for CHildren system or with the vehicle seat belt See Child restraints later in this section for more information NISSAN recommends that all pre teens and children be restrained in the rear seat Studies show that children are safer when properly restrained in the rear seat than in the front seat This is especially important because your vehicle has a supplemental restraint sys tem air bag system for the front passen ger See Supplemental restraint system later in this section INFANTS Infants up to at least 1 year old should
488. weight 1 000 lb 454 kg Available capacity 10 tongue weight The available towing capacity may be less than the maximum towing capacity due to the passen ger and cargo load in the vehicle Remember to keep trailer tongue weight be tween 10 15 of the trailer weight or within the trailer tongue load specification recommended by the trailer manufacturer If the tongue load becomes excessive rearrange the cargo to ob tain the proper tongue load Do not exceed the maximum tongue weight specification shown in the Towing load specification chart even if the calculated available tongue weight is greater than 15 If the calculated tongue weight is less than 10 reduce the total trailer weight to match the available tongue weight Always verify that available capacities are within the required ratings TOWING LOAD SPECIFICATION TOWING LOAD SPECIFICATION UNIT Ib kg MAXIMUM TOWING LOAD 1 1 000 454 MAXIMUM TONGUE LOAD 100 45 1 The towing capacity values are calculated assuming a base vehicle with driver and any options required to achieve the rating Additional passengers cargo and or optional equipment will add weight to the vehicle and reduce your vehicle s maximum towing capacity TOWING SAFETY Trailer hitch Choose a proper hitch for your vehicle and trailer Make sure the trailer hitch is securely attached to the vehicle to help avoid personal injury or prop erty damage due to sway cause
489. welve stations can be set for the FM band 6 for FM1 6 for FM2 Eighteen channels can be set for the SAT radio 6 for XM1 6 for XM2 6 for XM3 if so equipped 1 Choose the radio band AM FM1 or FM2 using the FM AM select button or choose the satellite band XM1 XM2 or XM3 using the SAT button 2 Tune to the desired station using manual SEEK or SCAN tuning Press and hold any of the desired station memory buttons 1 6 until the preset number is updated on the display and the sound is briefly muted 3 The channel indicator will then come on and the sound will resume Programming is now complete 4 Other buttons can be set in the same manner If the battery cable is disconnected or if the fuse opens the radio memory will be canceled In that case reset the desired stations List AM and FM Select the List key using the NISSAN controller or touchscreen to see a list of the presets in the AM FM1 or FM2 preset banks XM3 gt Favorite Artists 8 00 None Add Current Artist None Add Current Artist 1 8 Menu SiriusXM Satellite Radio if so equipped Select the Menu key using the NISSAN control ler or touchscreen to see a list of options Preset List Displays the list of presets Press and hold the touchscreen or ENTER button on the NISSAN controller to save a preset Customize Channel List deselect chan nels to skip while using the TUNE FOLDER knob Favorite Arti
490. will blink After the indica tor light goes off the keyfob is linked to that memory setting With the ignition switch placed in the OFF posi tion press the button on the keyfob The driver s seat and outside mirrors will move to the memorized position NOTE If a new memory position is saved to the memory switch the keyfob automatically re links Confirming memory storage Place the ignition switch in the ON position and push the SET switch If the main memory has not been stored the indicator light will come on for approximately 0 5 seconds When the memory has stored the position the indicator light will stay on for approxi mately 5 seconds Ifthe battery cable is disconnected or if the fuse opens the memory storage function will be canceled and must be restarted before a stored memory position can be set again Drive the vehicle over 25 MPH 40 km h to restart the memory storage function You can also restart the memory storage function using the following procedure Pre driving checks and adjustments 3 29 1 Connect the battery cable or replace the fuse 2 Open and close the driver s door more than 2 times with the ignition switch in the LOCK position Once the memory storage function has been restarted you can store a memory position See Memory storage function in this sec tion Selecting the memorized position Set the shift lever to the P Park position then Within 45 second
491. y See Call volume in this section Monitor climate audio phone and voice recognition systems 4 107 REGULATORY INFORMATION FCC Regulatory information CAUTION To maintain compliance with FCC s RF exposure guidelines use only the supplied antenna Unauthorized antenna modification or attachments could damage the transmitter and may violate FCC regula tions Operation is subject to the following two con ditions 1 This device may not cause interference and 2 this device must accept any interference including interference that may cause unde sired operation of the device IC Regulatory information Operation is subject to the following two con ditions 1 this device may not cause interfer ence and 2 this device must accept any interference including interference that may cause undesired operation of the device This Class B digital apparatus meets all re quirements of the Canadian Interference Causing Equipment Regulations BLUETOOTH is a trademark owned by Bluetooth SIG Inc and licensed to Clarion VOICE COMMANDS You can use voice commands to operate various Bluetooth Hands Free Phone System features using the NISSAN Voice Recognition system For more details see NISSAN Voice Recognition System if so equipped in this section amp Bluetooth Voice Prompt Interrupt In most cases you can interrupt the voice feed back to speak the next command by pr
492. y ap proved by the party responsible for compli ance could void the user s authority to op erate the equipment For Canada This device complies with RSS 210 of In dustry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference in cluding interference that may cause unde sired operation of the device Instruments and controls 2 57 MEMO 2 58 Instruments and controls 3 Pre driving checks and adjustments ROS geun eu suseceas E sarees e ere eeeetesr bene 3 2 NISSAN Intelligent Key 2 00000 3 2 NISSAN Vehicle Immobilizer System keys 3 3 DOCS ence coteiee neces CMoeueeueete een Sees ea at eee 3 4 LOCKING Wit K Viu s24522seu50eceeeucdemtdaexe wes 3 4 Locking with inside lock knob 45 3 5 Locking with power door lock switch 3 5 Automatic door locks o205cesseenueeceeseeree ua ss 3 6 Child safety rear door lock 0 0 0 ccc cence ees 3 6 NISSAN Intelligent Key 0 0000 c eee eee 3 7 Operating FaNnGCta ciuy couse aseseneceeeeserGades 3 8 Door locks unlocks precaution 3 9 NISSAN Intelligent Key Operation 3 10 How to use the remote keyless entry UNON xo3 cc6 cares Satbareecadeas EE T besa 3 13 Warning SiQnalS 22 lt 2cccteedcereedetseactosexe 3 15 Troubleshooting guide 02 022e0ee 3 16 MOOO 55g aate dese hon Ca
493. y depressing the brake pedal and pushing the push button ignition switch to start the engine If the engine starts but fails to run repeat the above procedure A CAUTION Do not operate the starter for more than 15 seconds at a time If the engine does not start push the ignition switch to the OFF position and wait 10 seconds before cranking again otherwise the starter could be damaged 4 Warm up Allow the engine to idle for at least 30 sec onds after starting Do not race the engine while warming it up Drive at moderate speed for a short distance first especially in cold weather In cold weather keep the en gine running for a minimum of 2 3 minutes before shutting it off Starting and stopping the engine over a short period of time may make the vehicle more difficult to start 5 To stop the engine shift the shift lever to the P Park position and push the ignition switch to the OFF position Starting and driving 5 11 NOTE Care should be taken to avoid situations that can lead to potential battery discharge and potential no start conditions such as 1 Installation or extended use of electronic accessories that consume battery power when the engine is not running Phone char gers GPS DVD players etc Vehicle is not driven regularly and or only driven short distances In these cases the battery may need to be charged to maintain battery health 5 12 Starting and driving DRIVING THE VEHIC
494. y is left near equipment which transmits strong radio waves such as sig nals from a TV and personal computer the bat tery life may become shorter For information regarding replacement of a bat tery see Battery replacement in the Mainte nance and do it yourself section As many as 4 Intelligent Keys can be registered and used with one vehicle For information about the purchase and use of additional Intelligent Keys contact a NISSAN dealer Pre driving checks and adjustments 3 7 A CAUTION Listed below are conditions or occur rences which will damage the Intelligent Key Do not allow the Intelligent Key which contains electrical components to come into contact with water or salt water This could affect the system function e Do not drop the Intelligent Key Do not strike the Intelligent Key sharply against another object Do not change or modify the Intelligent Key e Wetting may damage the Intelligent Key If the Intelligent Key gets wet im mediately wipe until it is completely dry Do not place the Intelligent Key for an extended period in an area where tem peratures exceed 140 F 60 C e Do not attach the Intelligent Key with a key holder that contains a magnet e Do not place the Intelligent Key near equipment that produces a magnetic field such as a TV audio equipment and personal computers 3 8 Pre driving checks and adjustments If an Intelligent Key is lost or
495. y out of the moonroof opening while the vehicle is in motion or while the moonroof is closing A CAUTION e Remove water drops snow ice or sand from the moonroof before opening e Do not place heavy objects on the moonroof or surrounding area Sunshade To open the sunshade To fully open the sunshade push the switch C toward the open position until it reaches the first detent To fully open the sunshade and the moon roof together push the switch 1 toward the open position until it reaches the second detent To close the sunshade To fully close the sunshade push the switch 2 toward the close position until it reaches the second detent Pushing the switch 2 to the first detent will close the moonroof only If the moonroof does not close Have your NISSAN dealer check and repair the moonroof REAR POWER SUN SHADE if so equipped The rear sun shade operates when the ignition switch is in the ACC or ON position The rear sun shade switch is located on the front console To raise the sun shade push the upper side of the switch 1 To lower the sun shade push the lower side of the switch The switch need not be held down Instruments and controls 2 49 INTERIOR LIGHT Driver s door is opened Lights remain on for a period of time after driver s door is closed A CAUTION Do not place objects such as newspa pers handkerchiefs etc on the screen

2014 Nissan Maxima

Contents

Download Pdf Manuals

Related Search

Related Contents