User Manual - Air-Con International
Contents
1. 2 Install outdoor unit Indoor unit check point Leak hunting Use soap water or leak hunting meter to check whether the joints is leak Outdoor unit check point Fig 6 Outdoor condensation drainage Heat pump type only When the unit is heating the condensing water and defrosting water can be drained out reliably through the drain hose Installation Install the outdoor drain elbow in 25 hole on the base plate and joint the drain hose to the elbow so that the wastewater ee Chasis formed in the outdoor unit can be drained out Zee 3 drai to a proper place Ea rain 22 Check after installation and test operation Check after installation Items to be checked Possible malfunction Has it been fixed firmly The unit may drop shake or emit noise Have you done the refrigerant leakage test It may cause insufficient cooling heating capacity Is heat insulation sufficient Is water drainage well Is the voltage in accordance with the rated voltage marked on the nameplate It may cause condensation and dripping It may cause condensation and dripping It may cause electric malfunction or damage the part Is the electric wiring and piping connection installed correctly and securely It may cause electric malfunction or damage the part Has the unit been connected to a secure earth connection It may cause electrical leakage Is the2. CF TEMP button e When press button the setting temp will be increased by 1 C When press button the setting temp will be decreased by 1 C The temp will be changed quickly by pressing the button continuously and setting temp range is 16 30 C 61 F 86 F FAN speed button e Press this button once fan speed will change as below C a Seed Low speed ez Middle speed aal High speed Note Under the Dry mode the fan speed isn t adjustable low fan speed is imperative but when operating this button the wireless remote control will send this signal Swing up and down button e Simpleness swing mode is defaulted for wireless remote control in this mode press this button could turn on or turn off the Up and down swing function e When unit is turned off synchronously press and Up and down swing buttons it could be switched between the simpleness swing mode and stationary swing mode at this time SA p SI blinks 2 seconds In Stationary swing mode press this button the angle for Up and down swing as show in below SHA a A SIRA B e When up and down swing louver is working when turn off the unit the siwng louver will immediately stop at current position zI shows up and down swing louver swings back and forth as show in the above figure Operation of remote control L Names and functions of remote control buttons NOTE This Remote control is uni
3. Clean and care HO CAUTION gd Turn power off and pull out the power plug before cleaning air conditioner Or it may cause electric shock e Never sprinkle water on the indoor unit and the outdoor unit for cleaning because it can cause an electric shock e Volatile liquid e g thinner or gasoline will damage the air conditioner So wipe the units with a dry soft cloth or a cloth slightly moistened with water or cleanser Clean the front panel make sure to take it off before cleaning D Take off the front panel Along the direction of arrows to lift the front panel up meanwhile to hold both slots of the front panel and take it out forcibly and then can take it off Washing Clean with a soft brush water and neutral dete rgent and then dry it Note Before cleaning the unit please take down the displayer box firstly then to wash the panel if the unit has displayer on the front panel Never use the water above 45 C to wash the panel or it could cause deformation or discoloration Install front panel Place two supporters of the front panel into the slots along the direction of arrows to cover and clasp the front panel As show in right figure Cleaning the air filters Recommended once every three months Note If dust is much more around the air conditioner the air filters should be cleaned many times After taking off the filter don t touch the fin of indoor unit in order to
4. YTT The wrong repair will lead to an electric shock or fire so you should contact the service center to repair amp Notices for operation dk Please don t cut off or damage the dk To adjust the airflow direction power cords and control cords appropriately When operating If they are damaged please ask the qualified the unit to adjust the vertical air flow dire personnel to change them ction by use of remote controller And then hold two ends of swing louver to adjust the horizontal airflow Swing louver Guide louver S Don t insert your hands or stick into S K Don t blow the wind to animals the air intake or outlet vents and plants directly It can cause a bad influence to them dk Don t apply the cold wind to K Don t use the air conditioner the body for a long time for other purposes such as It can cause the health problems drying clothes preserving foods etc lies RSSI E dk Splashing water on the air conditioner can cause an electric shock and malfunction dk Don t place a space heater near the air conditioner Notices for use Working principle and special functions for cooling Principle Air conditioner absorbs heat in the room and transmit to outdoor and discharged so that indoor ambient temperature decreased its cooling capacity will increase or decrease by outdoor ambient temperature Anti freezing function If the unit is running in COOL mode and in low
5. 36 000 Btu hr Mini Split Air Conditioner OWNER S MANUAL Air Con Air Conditioners Thank you for choosing an Air Con air conditioner Please take time to read this owner s manual carefully before operating the unit and st it carefully for future reference CONTENTS Operation and maintenance Notices for operation Notices for use Names and functions of each part Operation of wireless remote control Emergency operation Clean and care Troubleshooting nstallation service Notices for installation Installation dimension diagram Install indoor unit Install outdoor unit Check after installation and test operation Installation and Maintenance of Healthy Filter The physical product may differ from the drawing in this manual for different display If there are some differences between them please refer to the physical product as the standard ZE This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure they are away from the appliance A The figures in this manual may be different with the material objects please refer to the material objects for reference E This symbol stands for the items This symbol stands fo
6. Do not repair the air conditioner at your discretion Incorrect repair may cause electric shock or fire so please contact Authorized Service Center for professional repair Following checks prior to contact may save your time and costs Phenomenon Air conditioner does not run upon immediately restart after a stop pe Troubleshooting To protect the air conditioner upon immediate restart after a stop the microcomputer controller will delay the unit for 3 minutes before the air conditioner will run Air conditioner blows out bad smell when it is initially started di ek bie EAEE The air conditioner itself has no bad smell If any It is the bad smell accumulated from environment Solution Clean the air filter f still any problem the air conditioner shall be cleaned Please contact Authorized Service Center You may hear Water Flowing noise when the air conditioner is running When the air conditioner is started or the compressor is started or stopped during running or the air conditioner is stopped sometimes you may hear hua hua or di di noise This is the flowing sound of refrigerant other than fault Sometimes a thin fog will flow out of the outlet when air conditioner is running under cooling mode This might occur when indoor temperature and humidity are high This is because the indoor air is quickly cooled down After a period of time the fog will disappea
7. Criterion The user power must offer the reliable earthing terminal Please don t connect the earthing wire with the following place Tap water pipe Gas pipe 3 Contamination pipe Other places that professional personnel consider them unreliable The connection method of unit and power cable as well as the interconnect method of each isolated component should refer to the circuit diagram stick on the unit The model of the blown fuse and rated value should refer to the silk screen on the controller or fuse sleeve The appliance shall be installed in accordance with national wiring regulations This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard 17 Installation dimension diagram Installation dimension diagram 15cm Above Space to the wall r lt 300 e cm cm Above ae Air outlet side Space to the floor The dimensions of the space necessary for correct
8. can be lead out from right right rear B Gas side piping SOEK f Liquid side left left rear ipi 1 When routing the piping and wiring from the left i a or right side of indoor unit cut off the tailings debe from the chassis in necessary show in Fig 2 1 Cut off the tailings 1 when routing the wiring only 2 Cut off the tailings 1 and tailings 2 when routing both the wiring and piping or 1 2 3 Fi 2 insulation did Ig Finally wrap it insulation g wih tape Water drainage pipe Take out the piping from body case wrap the piping electric wire water pipe with tape and put them th Right SO rough the piping hole As show in Fig 3 Rightrear e Hang the mounting slots of the indoor unit on the q g Fixing hook upper tabs of the rear panel and check if it is firm d d SRA board y enough As show in Fig 4 Soa i ig Install the connection pipe Align the center of the piping flare with the relevant valve 2 Screw in the flare nut by hand and then tighten the nut with spanner and torque wrench refer to the following gerere Z Tightening torque table yw vee Hex nut diameter _ Tightening torque N m br GE 06 15 20 O R OS 52 31 35 Spanner L Ea Torque wrench Q 12 50 55 P 16 60 65 0 19 70 75 NOTE Firstly connect the connection pipe to indoor unit then to outdoor unit pay attention to the piping bending do not damage the connection pipe the joint nut could
9. installation of the appliance including the minimum permissible distances to adjacent structures Pi Q Space to the obstruction er lt 50cm Above Air inlet side SK WS ee 18 Install indoor unit Install the rear panel 1 Always mount the rear panel horizontally As the water drainage pipe at the left when adjusting the rear panel this side should not be too high the right side should be slightly high 2 Fix the rear panel on the selected location wa Wall 3 Be sure that the rear panel has been edad Ea ee s Y fixed firmly enough to withstand the weight GEZA ZI o F the wal of an adult of 60kg furthermore the weight ae dei E E Fa should be evenly shared by each screw Oe d uu bi ay Left Rear piping hole Rear piping hole Install the piping hole 1 Make the piping hole in the wall at a slight downward slant to the outdoor i Indoor Outdoor side Wall pipe 2 Insert the piping hole sleeve into the hole to prevent the connection Seal pad piping and wiring from being damaged when passing through the hole Install the water drainage pipe 1 For well draining the drain hose should be placed at a downward slant 2 Do not wrench or bend the drain hose or flood its end by water 3 When the long drainage hose passing through indoor should wrap the insulation materials Fl
10. power cord specified It may cause electric malfunction or damage the part Is the inlet and outlet been covered It may cause insufficient cooling heating capacity Has the length of connection pipes and refrigerant capacity been recorded The refrigerant capacity is not accurate Test Operation 1 Before test operation 1 Do not switch on power before installation isfinished completely 2 Electric wiring must be connected correctly and securely 3 Cut off valves of the connection pipes should be opened 4 All the impurities such as scraps and thrums must be cleared from the unit 2 Test operation method 1 Switch on power press ON OFF button on the wireless remote control to start the operation 2 Press MODE button to select the COOL HEAT FAN to check whether the operation is normal or not 23 Installation and Maintenance of Healthy Filter Installation Instructions 1 Forcibly pull the panel for a specific angle from the two ends of the front panel according to the arrow direction Then pull the air filter downwards to remove it See Fig a 2 Mount the healthy filter onto the air filter as shown in Fig b If the air filter cannot be in stalled please mount the healthy filter on the front case as shown in Fig c 3 Mount the air filter properly along the arrow direction in Fig d and then close the panel cover Cleaning and Maintenance Tak
11. termperature there will be frost formed on the heat exchanger when indoor heat exchanger temperature decreased below 32 F the indoor unit microcomputer will stop compressor running and protect the unit Working principle and special functions for heating Principle Air conditioner absorbs heat from outdoor and transmits to indoor in this way to increase room temperature This is the heat pump heating principle its heating capacity will be reduced due to outdoor temperature decrease If outdoor temperature becomes very low please operate with other heating equipments Defrosting When outdoor temperature is low but high humidity after a long while running frost will form on outdoor unit that will effect the heating effect at this time the auto defrosting function will act the heat running will stop for 8 10mins During the auto defrosting the fan motors of indoor unit and outdoor unit will stop During the defrosting the indoor indicator flashes the outdoor unit may emit vapor This is due to the defrosting it isn t malfunction After defrosting finished the heating will recover automatically Anti cool wind function In Heat mode the following three kinds of status if indoor heat exchanger hasn t achieve certain temperature that indoor fan motor will not start in this way to prevent blowing cool wind within 3mins 1 Heat operation just startedup 2 After Auto defrosting operation is finished
12. the mian unit will click SE will be displayed on the LCD of wireless remote control fan speed automatically rotates when repress this button the fan speed will run at previous setting fan speed TORBY Turbo button e Set turbo on or off the characters of turbo will appear or disappear by pressing this key under cooling or heating mode Once energized the unit will be defaulted to be turbo off This function can not be set under auto dehumidify or fan mode and characters of turbo won t appear Operation of remote control d Names and functions of remote control buttons NOTE This remote control is universal it could be used formany units some buttons of this control which are not available to this unit will not be described below X FAN FAN AUTO eg OPER AIR HEALTH KEAN hl b UO 7 O ek E D Remote control X FAN button e Set X FAN on the characters of X FAN will appear or off the characters of X FAN disappear by pressing this key under cool or dehumidify mode Once energized the unit will be defaulted to be X FAN off This function can not be set under auto fan or heat mode and the characters of X FAN won t appear Note X FAN or BLOW same function different name LIGHT TEMP TIMER SLEEP LIGHT GREE SLEEP Sleep button e Press this button enter into SLEEP state when repressed it
13. will quit The sleep function will be canceled with the stop of the unit There is no SLEEP function under AUTO and FAN mode is the icon for sleep function At COOL X FAN mode the SLEEP mode runs after 1hour the setting temp will be increased by 1C 2 hour later setting temp will be increased by 2 C and then will run at this setting temperature At HEAT mode the SLEEP mode runs after 1hour the setting temp will be decreased by1 C 2 hours later setting temp will be decreased by ZO then it will run at setting temperature TEMP Light button e Press this button to select LIGHT on or off in the displayer When the LIGHT on is set the icon w will be displayed and the indicator light in the displayer will be on When the LIGHT off is set the icon will be displayed and the indicator light in the displayer will be off Temp display button e There is no this function for this unit If press this key the main unit will click but it also runs under original status Operation of remote control E Guide for operation general operation 1 Press ON OFF button to start the unit after powering the main unit on Note Power the unit on every time the big guide louver and small guide louver will be closed firstly 2 Press MODE button to select desired running mode 3 Press button to set the desired temperature It is unnecessary to set the tem
14. 3 Heating under low temperature The climate type of this unit is according to the nameplate Installation must be performed in accordance with the NEC CEC by authorized person only Names and functions of each part Indoor unit BERRE 1 Front panel 2 Filter 3 Guide louver LL ki 4 Wall pipe 5 Bind tape Outdoor unit 6 Connection wire 7 Drainage pipe 8 Remote control CTT TTT AAT TA Air out Operation of remote control C Names and functions of remote control buttons N Note Be sure that there are no obstructions between receiver and remote control Don t drop or throw the remote control Don t let any liquid in the remote control and put the remote control directly under the sunlight or any place where is very hot Signal transmitter FAN AUTO F ag OPER AIR HEALTH X FAN won m a k FLTER a E o G8 Gener E CII 3 zl INS gt or EO EE Remote control GREE ON OFF ON OFF button e Press this button the unit will be started or stopped which can clear the timer or sleeping function of last time MODE Mode button e Press this button the running mode will change as below 6 dd oe at As Sd A bardi A AUTO COOL Ak DRY FAN XE HEAT Note no for coolling FAN only unit
15. There is harsh sound during operation The terrible odors emitted during operation Water is leaking in the room Air switch or protection switch often breaks gt sep running and pull out of the pug Carelessy splash water or something into unit There is an abnormal heat in power supply cord and power plug b J 15 Installation service Notices for installation CONAD 1 The unit installation work must be done by qualified personnel according to the local rules and this manual 2 If the air conditioner has not plug directly connect it into the fixed circuit a breaker should be installed in the fixed circuit all pole of this breaker should be switching off and the distance of the contact should be at least 3mm Basic Requirements For Installation Position Install in the following place may cause malfunction If it is unavoidable contact with service center please Place where strong heat sources vapors flammable gas or volatile object are emitted Place where high frequency waves are generated by radio equipment welders and medical equipment Place where a lot of salinities such as coast exists e Place where the oil machine oil is contained in the air e Place where a sulfured gas such as the hot spring zones is generated Other place with special circumstance Indoor Unit Installation Position Selection 1 The air inlet and outlet vent should be far from the obst
16. avoid hurt your fingers bb d Clean and care Take down the air filter At the slot of surface panel to open an angle pull the air filter downward and take it out 2 Cleaning To clean the dust adhering to the filters you can either use a vacuum Cleaner or wash them with warm water the water with the neutral detergent should below 45 C When the filters are very dirty such as oil stain and dry it in the shade NOTE Never use water above 45 C to wash or it can cause deformation or discoloration Never partch it by fire or can cause a fire or deformation 8 Reinsert the filters Reinsert the filters along with the arrow head then cover the surface panel and clasp it Be sure that nothing obstructs the air outlet and intake vents 2 Check that whether ground wire is properly connected or not 8 Check that whether the batteries of air conditioner are changed or not 4 Check that whether the installation stand of the outdoor unit is damaged or not If damaged please contact the dealer Maintain after use GN Turn main power off Q Clean the filter and indoor and outdoor units bodies GN Clear dust and obstructions from the outdoor unit EN Repaint the rubiginous place on the outdoor unit to prevent it from spreading Adopt the special shield to cover the outdoor unit avoid the rain water dust enter into the unit and get rust KONEK Troubleshooting ACD
17. e out the healthy filter before cleaning and reinstall it after cleaning according to the installation instruction Pay special attention to that silver ion filter can t be cleaned with water while active carbon photocatalyst low temperature conversion LTC catalyst formaldehyde eliminator ca techin or mite killing filter can but can t with brush or hard things Dry it in the shade or sun after cleaning but not by wiping The healthy filter commonly has its usage lifetime for one year under normal condition As for silver ion filter it is invalid when its surface becomes black green This supplementary instruction is provided for reference to the unit with healthy filter If the graphics provided herein is different from the physical goods the latter one shall prevail The quantity of healthy filters shall be based on the actual delivery 24 Air Con Inc Carr 2 km 16 5 Barrio Candelaria Toa Baja P R 00949 Website www airconpr com
18. g in COOL mode the pipe and connection of pipe would be condensed due to the water cooled down When the unit is running in Auto Defrosting mode the ice thawed and flowed out When the unit is running in HEAT mode the water adhered on heat exchanger dripped off Noise from indoor unit emitted The sound of fan or compressor relay is switching on or off When the defrosting is started or stop running it will sound That is due to the refrigerant flowed to the reverse direction 4 Troubleshooting Phenomenon Troubleshooting In HEAT mode when the temperature of Indoor unit cannot deliver air indoor heat exchanger is very low that will stop deliver air in order to prevent cool air Within 3min in HEAT mode when the outdoor temperature is low or high humidity there are much frost be formed on the outdoor heat exchanger that the unit will automatically defrost indoor unit stop blowing air for 3 12mins During the defrosting there is water flowing out or vapor be produced In dehumidifying mode sometimes indoor fan will stop in order to avoid condensing water be vaporized again restrain temper ature rising Moisture on air outlet vent if unit is running under the high humidity for a long time the moisture will be condensed on the air outlet grill and drip off O Immediately stop all operations and plug out contact 2 the dealer in following situations x
19. height difference of connecting the tubing within 5m the length of connecting the tubing within 10m 8 Select a place where it is out of reach for the children 9 Select a place where will not block the passage and do not influence the city appearance 16 Notices for installation Safety Requirements For Electric Appliances 1 The power supply should be used the rated voltage and AC exclusive circuit the power cable diameter should be satisfied 2 Don t drag the power cable emphatically 3 It should be reliably earthed and it should be connected to the special earth device the installation work should be operated by the professional The air switch must have the functions of magnetic tripping and heat tripping in order to protect the short circuit and overloading 4 The min distance from the unit and combustive surface is 1 5m Note Make sure that the Live wire or Zero line as well as the earth wire in the family power socket can not be wrong connected there should be reliable and no short circuit in the diagram wrong connection may cause fire Earthing requirements Air conditioner is type electric appliance thus please do conduct reliable earthing measure The yellow green two color wire in air conditioner is earthing wire and cannot be used for other propose It cannot be cut off and be fix it by screw otherwise it would cause electric shock The earth resistance should accord to the National
20. hem out e e Sketch map for after 30s later and reinsert if they cannot normally run please change them changing batteries x Emergency Operation Displayer indicator light control of indoor unit It s a special selective button for the users who are not accustomed to the light at sleeping Get the displayer indicator light on When setting the light function the mark will display on the remote controller screen by pressing this button In which case the diss player indicator light will be on if the AC receives this signal Get the displayer indicator light off If cancel the light function the mark will disap per on the remote controller screen by pressing this button In which case the displayer indicator light will be off if the AC receives this signal Emergency Operation When the wireless remote control is lost or damaged please use the manual switch at this time it is running in Auto Run mode that will not change the temperature setting value and fan speed The manual switch can be operated as follow At operation When the unit stopped running press ON OFF button unit will enter into AUTO RUN mode The microcomputer will accord to the room temperature to select the COOL HEAT FAN mode automatically to obtain the comfortable effect AUTO STOP Manual Switch At stopping When the unit is running press the ON OFF button of the manual switch the unit will stop work 10
21. ll run at super high fan speed to cool or heat quickly so that the ambient temp approachs the preset temp as soon as possible dk About lock Press and buttons simultaneously to lock or unlock the keyboard If the remote controller is locked the icon jg will be displayed on it in which case press any button the mark will flicker for three times If the keyboard is unlocked the mark will disappear dk About switch between Fahrenheit and Centigrade Under status of unit off press MODE and buttons simultaneously to switch C and F Changing batteries and notices 1 Slightly to press the place with along the arrowhead direction to push the back cover of wireless remote control As show in figure 2 Take out the old batteries As show in figure 3 Insert two new MALEN dry batteries and pay attention to the polarity As show in figure 4 Attach the back cover of wireless remote control As show in figure SK NOTE When changing the batteries do not use the old or different batteries otherwise it can cause the malfunction of the wireless remote control f the wireless remote control will not be used for a long time please take them out and don t let the leakage liquid damage the wireless remote control The operation should be in its receiving range It should be placed at where is 1m away from the TV set or stereo sound sets If the wireless remote control can not operate normally please take t
22. n t tighten too much otherwise it may cause leakage SUA Install outdoor unit Electric Wiring 1 Disassemble handle of right side plate or front side plate of outdoor unit 2 Take off wire clamp connect and fix power connect cord and power cord to terminal of line bank Wiring should fit that of indoor unit 3 Ensure if wire has been fixed well 4 Install handle or front side plate NOTE Wrong wiring may cause spare parts malfunction After the cable fixed make sure there should be a free space between the connection and fixing place on the lead wire Air purging and leakage test Air purging and leakage test 1 Connect charging hose of manifold valve to charge end of low pressure valve both high low pressure valves must be tightly shut Connect joint of charging hose to vacuum pump Fully open handle of Lo manifold valve Open the vacuum pump to evacuate At the beginning slightly loosen joint nut of low pressure valve to check if there E awd is air coming inside If noise of vacuum pump has d e been changed the reading of multimeter is 0 Then tighten the nut Liquid pipe Gas pipe wD Keep evacuating for more than 15mins and make sure the reading of multi meter is i 0 x 10 pa fo Vacuum pump 76cmHg Fig 5 Fully open high low pressure valves Remove charging hose from charging end of low pressure valve 8 Tighten bonnet of low pressure valve As shown in Fig 5
23. ooded Connect indoor and outdoor electric wires 1 Open the front panel upwardly 2 Screw off the fixing screw of cover plate and screw off cover plate 3 Put the power connection cable through the back of indoor unit wire hole and take it out 4 All the wiring should be connected according to the circuit diagram on the unit 5 Put the power connection cable the section which with sheath into wire groove and cover the cover plate screw on the fixing screw tighten the connection wire 6 Cover the front panel cover 19 Install indoor unit NOTE When connecting the electric wire if the wire length is not enough please contact with the authorized service shop to buy a exclusive electric wire that is long enough and the joint on the wire are not allowed The electric wiring must be correctly connected wrong connection may cause spare parts malfunction Tighten the terminal screw in order to prevent loose After tighten the screw slightly pull the wire and confirm whether is it firm or not f the earth wire is wrong connection that may cause electric shock The cover plate must be fixed and tighten the connection wire if it is poor installed that the dust moisture may enter in or the connection terminal will be affected by outside force and will cause fire or elelctric shock e Leakage circuit breaker and air switch of correct capacity must be installed Install the indoor unit The piping
24. perature at AUTO mode 4 Press FAN button to set fan speed the AUTO FAN LOW MID or HIGH could be selected 5 Press SI button to set swing mode a TEMP TIMER SLEEP LIGHT TS GREE C Guide for operation optional operation 1 Press SLEEP button set the sleep mode 2 Press TIMER button then press button to set the cheduled timer on or timer off 3 Press light button to control displayer light on or off 4 Press X FAN button to set X FAN function on or off 5 Press turbo button to set this function on or off d Introduction for special function K About X FAN function This function indicates that moisture on evaporator of indoor unit will be blowed after the unit is stopped to avoid mould 1 Having set X FAN function on After turning off the unit by pressing ON OFF button indoor fan will continue running for about 10 min at low speed In this period press X FAN button to stop indoor fan directly 2 Having set X FAN function off After turning off the unit by pressing ON OFF button the complete unit will be off directly Operation of remote control K About AUTO RUN When AUTO RUN mode is selected the setting temperature will not be displayed on the LCD the unit will be in accordance with the room temp automatically to select the suitable running method and to make ambient comfortable x About turbo function If start this function the unit wi
25. r with the decrease of indoor temperature and humidity You may hear a slight crack when the air conditioner is started or stopped This is the sound of friction caused by expansion of panel or other parts due to the change of temperature 13 Troubleshooting Phenomenon The unit can not run Troubleshooting Has the power been shut down Does power plug come loose from the socket Is the circuit protection device tripped off or not Is voltage higher or lower Tested by professionals Is the Timer correctly used Is Temp setting suitable Were inlet and outlet vents obstructed Is there too much dusts accumulated and obstructed the filter Are the windows and doors closed Did Fan speed set at low speed Is there any heat sources in the room The unit is interfered by abnormal or frequent functions switchover occasionally the controller cannot operate At this time you need to pull out of the plug and reinsert it s it in its receiving range Or obstructed To check the voltage in wireless remote control inside is charged otherwise to replace the batteries Whether the wireless remote control is damaged If water leakage in the room The air humidity is on the high side Condensing water over flowed The connection position of indoor unit drainage pipe is loosed If water leakage in outdoor unit When the unit is runnin
26. r the items 4 should be forbidden should be followed Do not dispose this product as unsorted municipal waste Collection of such waste separately for special treatment is necessary A Operation and maintenance notices for operation A Earth The ground be con nected If not please ask the qualified person nel to install Furthermore don t conn ect each wire to the gas pipe water pipe drainage pipe or any other impr oper places bi Be sure to pull out the power plug when not using the air conditiiner for a long time Otherwise the accumulated dust may cause fire or electric shock Select the most appropriate tem perature It can preclude the electricity wasted Don t leave windows and doors open for a long time while operating the air conditioner It can decrease the air conditioning capacity Don t block the air intake or outlet vents of both the outdoor and indoor units It can decrease the air conditioning capacity or cause a malfunction Keep combustible spray away from the units more than 1m It can cause afire or explosion Please note whether the installed stand is firm enough or not If it is damaged it may lead to the fall of the unit and cause the injury Don t step on the top of the outdoor unit or place something As falling off the outdoor unit can be dangerous zk Don t attempt to repair the air conditioner by yourself
27. ruction make sure that the air can be blown through the whole room Select a position where the condensing water can be easily drained out and the place is easily connected for outdoor unit Select a location where the children can not reach Can select the place where is strong enough to withstand the full weight and vibration of the unit And will not increase the noise Be sure to leave enough space to allow access for routine maintenance The height of the installed location should be 230 cm or more from the floor Select a place about 1m or more away from TVset or any other electric appliances Select a place where the filter can be easily taken out Make sure that the indoor unit installation should accord with installation dimension diagram requirements Outdoor Unit Installation Position Selection Select a location from which noise and outflow air emitted by unit will not inconvenience neighbors animals plants Select a location where there should be sufficient ventilation Select a location where there should be no obstructions cover the inlet and outlet vent The location should be able to withstand the full weight and vibration of the outdoor unit and permit safe installation Select a dry place but do not expose under the direct sunlight or strong wind Make sure that the outdoor unit installation dimension should accord with installation dimension diagram convenient for maintenance repair The
28. versal it could be used formany units some buttons of this control which are not available to this unit will not be described below EZE d TIMER AIR HEALTH X FAN Timer button an 4 ay cam ar e e On the status of the unit on press this sa TURo am button to set timer off On the status of the unit off press this button to set timer off Press this key once words Hour on off will appear and flicker In which case press button to adjust time press button continuously to change timing value quickly Can LZ the setting time range is from 0 5 to 24 hr press this key once again to fix the time bri CH then remote controller will send out the signal kran Teme rmen immediately and hour on off will stop flickering bezi bezi Dz If the time of that no press timer button under flickering status is above 5s the timer setting will quit If the timer has been set press this button once again to quit it HEALTH SAVE button ZINN Remote control GREE HEALTH SAVE Left and right swing button e HEALTH function there is no this function for this unit If press this key the main unit ere is no this function for this unit If press will click but it also runs under original status this key the main unit will click but it also runs igi e Save energy function this unit has no this under original statuis function press this button
Download Pdf Manuals
Related Search