SeaChanger™ Tungsten Profile & Wash
Contents
1. Specification Value Mechanical Height inches Profile 11 5 in Wash 11 5 in Width inches Profile 7 0in Wash 7 0 in Length inches Profile 29 5 in Wash 21 8 in without ETC Source Four Profile with ETC Source Four 26 30 in Wash 22 in Shipping Weight Profile 20 Ibs Wash 23 Ibs Actual Product Weight Profile 16 Ibs Wash 19 Ibs Electrical Non dimming circuit 100 250 VAC 50 60 Hz auto sensing 1 25 amps typical 115 VAC 0 80 amps typical 230 VAC Onboard internal 24VDC 60W switching mode power supply Fuse T3 15 A 250 V internal fuse in line and neutral Fuse is integral to power supply and not user replaceable Environmental Maximum Ambient Temperature 30 C 86 F Minimum Ambient Temperature 0 C 32 F Maximum Exterior Surface Temperature 200 C 392 F Cooling Integral 4 7 CFM speed controlled fan Speedster only Lamp Type 575W or 750W HPL incandescent lamp can be used with Source 4 HID high intensity discharge fixtures Control Cabling and Terminator SeaChanger Tungsten Data Link 8 bit DMX512 male and female 5 Pin XLR with DMX signal pass through for daisy chaining Remote Device Management RDM per ANSI E1 20 2006 DMX start address can be set via RDM or onboard display Maximum Recommended Cable Length 182 9 m 600 ft Compatible Terminator 120 ohms SeaChanger Tungsten2. Description TUNGSTEN Tungsten Legacy Silent no fans A451 01 03 Profile XG Tungsten CYM w XG Filter Wheel A451 01 01 Profile XG Tungsten CYM w Dimmer Wheel A451 01 04 Profile Studio Dichroic Tungsten CYM w XG Whl A451 01 05 Profile Studio Dichroic Tungsten CYM w Dimmer Whl A474 01 03 Wash Tungsten CYM w XG Filter Whl A474 01 01 Wash Tungsten CYM w Dimmer Wheel Tungsten Speedster 5 sec color change A451 02 03 Profile XG Tungsten CYM wl XG Filter Wheel A451 02 01 Profile XG Tungsten CYM w Dimmer Wheel A451 02 04 Profile Studio Dichroic Tungsten CYM w XG Whl A451 02 05 Profile Studio Dichroic Tungsten CYM w Dimmer Whl A474 02 03 Wash Tungsten CYM wl XG Filter Whl A474 02 01 Wash Tungsten CYM w Dimmer Wheel Tungsten Special A451 01 06 Profile Tungsten LDS A451 02 08 Carnival Profile Tungsten SD Dbl Cl Hi Temp HMI HMI Speedster 5 sec color change A451 533 Profile HMI CYM and Dimmer A474 533 Wash HMI CYM and Dimmer A451 533 OD Outdoor Profile HMI CYM amp Dimmer IP 54 A474 533 OD Outdoor Wash HMI CYM amp Dimmer IP 54 HMI Special PPA451 100 Inno Kit Back end HMI PPA451 300 Inno Kit Back end HMI 3000 Hour Lamp A451 533 Seachanger Profile HMI only no light source Speedster A451 533 10 SB Seach
3. The installed SeaChanger Tungsten can be oriented in either the in yoke or below yoke configurations as shown below WARNING If you are using SeaChanger and Wash with the 11 inch or the Seachanger 16 inch extended yoke accessory you must position the SeaChanger Profile or Wash at no greater angle than 70 degrees to vertical when the front barrel is pointing upward This prevents the build up of excessive lamp heat that can affect SeaChanger operation N d Optimizing Beam Angle SeaChanger Tungsten Profile For optimum performance from the Source Four front end barrel when you need a soft edge always move the lens tube out away from the lamp housing from the focus point not towards To sharpen the focus move one beam shutter into the beam and move barrel back and forth to achieve a sharp focus SeaChanger Tungsten Wash The Wash field size can be adjusted with the manual zoom adjust knob located on the opposite side of the lens housing from the drive enclosure Simply loosen and move the knob forward in the direction of the output Fresnel lens for 70 degree wide field coverage or to the rear towards the lamp housing for a tight 20 degree field with superior edge softness When the desired wash field is obtained retighten the knob to set the adjustment e Determining a Valid DMX Base Address for Seachanger Profile and Wash The DMX base address start channel identifies each fixture on a
4. fixture 7 performance optimizing 6 power cord cap installing 9 product documentation iii product modification i purpose iii repair i returning product i RDM control 11 12 13 RoHS Compliance 18 safety information i SeaChanger 5 Seachangerfixture numbers 21 setup 5 soft edge beam 7 Source Four 2 6 7 spare parts 20 specifications 16 17 speedster 2 summary iii unpacking 4 upgrades iii USITT DMX512 Manuf ID 10 W warning i 5 6 7 19 warranty i freight ii wheel sets 2
5. mixing from smooth transition movements to rapid color snaps and bumps Silent operation Legacy Quiet operation Speedster Live color fading from one color to another with no intermediate colors The Profile will exhibit no interference with Source Four gobos irises or gobo rotators Operates on four DMX channels Cyan Magenta Yellow and xG CMY and douser for the DM dimmer model The Seachanger Tungsten Wash has manual zoom optics from 20 to 70 degrees of angle Wash has an adapter to accept Barn Doors and Top Hats The Wash uses a Fresnel lens for soft edge projection 0 1 02 02 04 05 06 07 08 xG Gamut Range SeaChanger Tungsten Color Gamut Chapter 2 Setup and Configuration Unpacking the Products Unpack your SeaChanger products and verify that they are undamaged If there is no damage continue with the rest ofthe setup procedure see SeaChanger Tungsten Setup Ifthere is damage notify both the shipping agent and the sales agent immediately Save the shipping carton and packing materials The carton and packing materials are specifically designed to protect the product during transport Return a product for repair in its original shipping carton and packing materials SeaChanger assumes no responsibility for products that are damaged during transport Please call for a Return Material Authorization RMA number prior to return SeaChanger cannot accept any goods shipp
6. numeric entry Each button push increments the corresponding digit by 1 and from 9 back to 0 Addresses and functions programmed via the display panel take effect after a 3 second delay d DMX Signal Indicator The SeaChanger display will show a decimal point if a DMX signal is present The decimal point will go out when signal is not present or removed zf e Display Blanking The SeaChanger display will blank the digits after a short delay The DMX signal indicator decimal point will remain on as long as a DMX signal is present The display can be powered on by pushing any of the display buttons once while blanked f USITT DMX512 A Manufacturer ID All SeaChanger Tungsten Profile and Wash DMX512 addressable fixtures have an ESTA registered Manufacturer s ID of ASCII SC decimal 83 amp 67 or 53h 43h in hex See http www esta org tsp working groups CP mfctriDs php for more information g DMX Control When connected to a suitable DMX controller the SeaChanger can be operated via four DMX channels The channels are assigned as in Table 1 below Table 1 SeaChanger Tungsten Profile and Wash DMX Channel Map Reset DMX Default ee Name Parameter Sobel Ess ange Range ange Percent Value Color o 0 1 Cyan Baden a ee IE iiber Color o 0 2 Magenta Saturation 0 100 0 255 0 FF Full clear Color o 0 3 Yellow Saturation ir nn Sr Full clear xGRB Color _ o 0 j Model SEA
7. 0 4 8 EN 610004 11 RoHs Directive 2002 95 EC WEEE Directive 2002 96 EC Part 15 of FCC Rules Technical documents are maintained at Ocean Thin Films Largo Florida and will be made available upon request Appendix B Maintenance Cleaning the SeaChanger Tungsten Dichroic WARNINGS Disconnect power cord connector from power source to isolate SeaChanger from line voltages before servicing Equipment surfaces may reach temperatures up to 67 C 153 F Allow the fixture to cool before handling Remove the SeaChanger Tungsten color engine cassette from the lens tube assembly by removing 4 Philips screws and extracting the color engine as shown The filters can be easily accessed by removing 4 Philips screws and pulling the protective cage away from the color engine as shown below Clean the dichroic glass filters using a mild glass cleaner containing no ammonia and a soft lint free cotton cloth or swab Reverse the above steps for reassembly When reassembling ensure that the cage is oriented in the same direction as it was removed the cage has a retaining slot for the aperture stop that will bend the aperture stop out of position if installed incorrectly Spare Parts EL451 20 EL451 20A motor shaft pulley mount motor shaft pulley mount motor shaft pulley mount motor shaft pulley mount SA533 05A Plasma Lamp Assembly AEL 533 09 RF Generator with Wires Part Number Fixture Part Numbers
8. 3 Magenta 917 17 L 103 Straw 918 18 L 124 Dark Green 919 19 L 166 Pale Red 920 20 L 004 Medium Bastard Amber 921 21 Roscolux 310 Daffodil 922 22 Roscolux 46 Magenta 923 23 Roscolux 99 Chocolate 924 24 Roscolux 62 Booster Blue 925 Gel Match demo colors 1 24 are based on Osram HPL750 115 lamp To cancel demo mode select a DMX base address between 1 and 509 via RDM or keypad Table 4b SeaChanger Tungsten DM Optional Douser Demo Sequence Sequence e RDM Number Function Keypad Equivalent 1 Cyan Full 901 2 Magenta Full 902 3 Yellow Full 903 4 L 079 Just Blue 905 5 L 110 Middle Rose 906 6 L 104 Deep Amber 907 7 L 105 Orange 908 8 L 164 Flame Red 909 9 L 322 Soft Green 910 10 Roscolux 60 No Color Blue 911 11 Roscolux 51 Surprise Pink 912 12 Roscolux 21 Golden Amber 913 13 Roscolux 82 Surprise Blue 914 14 Roscolux 04 Medium Bastard 915 Amber 15 L 142 Pale Violet 916 16 Roscolux 02 Bastard Amber 917 17 Roscolux 46 Magenta 918 18 Roscolux 59 Indigo 919 19 L 136 Pale Lavender 920 20 L 035 Light Pink 921 21 L 158 Deep Orange 922 22 L 248 Half Minus Green 923 23 Roscolux 05 Rose Tint 924 24 L 162 Bastard Amber 925 Gel Match demo colors 1 24 are based on Osram HPL750 115 lamp To cancel demo mode select a DMX base address between 1 and 509 via RDM or keypad Appendix A SeaChanger Tungsten Specifications
9. Certifications Provides product specifications Provides for cleaning the SeaChanger Plasma Appendix B Maintenance and part Profile and Wash dichroic numbers You can access documentation for SeaChanger Tungsten Profile and Wash by visiting our website at www SeaChangerOnline com Upgrades Occasionally you may find that you need SeaChanger to make a change or an upgrade to your system To facilitate these changes you must first contact Customer Service and obtain a Return Merchandise Authorization RMA number Please contact SeaChanger for specific instructions when returning a product Chapter 1 Features and Product Description SeaChanger Tungsten Profile amp Wash Color Engine The SeaChanger Tungsten Color Engine is an innovative dichroic color mixing accessory for the ETC Source Four ellipsoidal fixture SeaChanger Tungsten gives you the freedom to mix any color as well as perform live fades from one color to another smoothly silently and cleanly The SeaChanger Tungsten color wheels utilize dichroic borosilicate glass which will not fade or change color The SeaChanger Tungsten s are available in the standard xG configuration p n 451 01 03 which features a multiband trichroic RGB filter in addition to the cyan magenta and yellow filters and in the optional DM dimmer configuration p n 451 01 01 with a patterned aluminum douser in place of the xG filter The SeaChanger T
10. Onboard Keypad Display Three button shielded membrane keypad with three digit seven segment LED display and DMX signal indicator Operating Features Color Filter Type Range and Control Channel 1 Cyan 0 95 saturation SD 100 saturation Channel 2 Magenta 0 95 saturation SD 100 saturation Channel 3 Yellow 0 95 saturation SD 100 saturation Channel 4 standard xG RGB filter 0 99 saturation optional patterned Al douser 0 99 dimming custom dichroic filters Dichroic patterned CMY and xG RGB coatings on optical glass substrates BBAR coated in band transmission gt 98 Patterned aluminum douser SEA DM model with dielectric enhancement on optical glass substrate Speed Speedster 0 3 sec Legacy 1 0 sec clear to full saturation Onboard drive electronics with adaptive speed response Accessory Compatibility Preserves all ETC Source Four beam characteristics and compatibility with all beam shaping ETC Source Four accessories such as gobos gobo rotators gobo changers and 10 14 26 36 50 70 and 90 degree field of view barrels and other beam shaping devices Mounting Suspension on Source Four yoke from mounting points Bayonet mount to fixture Adaptable to Source Four tungsten or HID fixtures Maintenance Easy color engine removal for periodic cleaning Safety Safety cable ring 3 safety cable included For more information see the documentation fo
11. SEACHANGER 6 k SeaChanger Tungsten Profile amp Wash Legacy and Speedster Models Installation and Operation Manual SEACHANGER vw a product of PIXELTEG By Ocean Thin Films 8060 Bryan Dairy Road Largo FL 33777 Ph 727 545 0741 www seachangeronline com www pixelteq com FCC Information This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 ofthe FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense Copyright 2001 2011 SeaChanger All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without written permission from SeaChanger This manual is sold as part of an order and subject to the condition that it shall not by way of trade or otherwise be lent re sold hired out or otherwise circulated without the prior consent of SeaChanger in any form of bindin
12. X block of 4 contiguous channels f Setting the Base DMX Address The SeaChanger Tungsten Profile and Wash are four channel DMX devices and requires that a contiguous block of four DMX addresses be available The display panel or RDM input is used to enter the DMX base address of the fixture Channel 1 is assigned to this base address and Channels 2 through 4 are assigned the next three DMX addresses Chapter 3 Operation Overview a General operation b Power and DMX Connection c Display and Control Buttons d DMX Signal Indicators e Display Blanking f USITT DMX 512 A Manufacturing ID g DMX Control h Reset from Console i Keypad Control j RDM Control k Demo Mode a General Operation The SeaChanger can be operated by a DMX512 controller RDM Remote Device Management device or from the front panel display b Power and DMX Connections The SeaChanger has a self contained universal AC DC power supply permitting connection to single phase power sources with a voltage range of 100 250 VAC at a frequency of 50 60 Hz The DMX I O connectors are 5 pin XLR type and are connected in a pass through arrangement to enable daisy chaining of multiple fixtures Either connector can function as an input or output An external terminator plug not supplied is recommended for the last fixture in a DMX cable run c Display and Control Buttons The SeaChanger features a 3 digit LED display and corresponding panel buttons for
13. XG Saturation OSOA gt er Full clear Optional Douser Brightness 0 100 0 255 0 FF F ie k Model SEA DM 2 h Reset from DMX Console When connected to a suitable DMX controller the SeaChanger filter wheel positions can be reset from the console by a two step dwell and snap as shown in Table 2 below Table 2 SeaChanger Tungsten Profile and Wash Reset Procedure Dwell 3 sec Snap Reset Default Channel Name I DMX hex DMX hex Percent Value 1 Cyan 100 255 FF 0 0 0 Ger Full clear O 2 Magenta 100 255 FF 0 0 0 GE Full clear 0 O O 3 Yellow 100 255 FF 0 0 0 Full clear O xGRB 0 0 0 0 0 0 oe Model SEA XG Full clear 4 Optional o 0 Douser 0 0 0 0 0 0 Model SEA DM Full Dark i Keypad Control The SeaChanger keypad and LED display provides another interface to set the fixture base address select the operating mode and program settings Settings take effect after a three second delay These parameters are shown in Table 3 j RDM Control The SeaChanger is RDM Remote Device Management compliant to ANSI E1 20 2006 Entertainment Technology Remote Device Management over USITT DMX512 RDM allows the SeaChanger base DMX address to be remotely set and the operating mode or fixture settings to be changed Available functions are listed in Table 3a for the SeaChanger xG and in Table 3b for the SeaChanger DM optional patterned alumi
14. anger wash HMI only no light source Legacy PLASMA Plasma Legac Silent no fans A533 01 01 Plasma Profile CYM DM A533 01 10 Plasma Wash CYM DM A533 500 01 CTE Plasma Profile White Light Fixture A533 600 01 CTE Plasma Profile CTO Dimmer A533 510 CTE Plasma Wash White Light Fixture A533 610 CTE Plasma Wash CTO Dimmer A638 01 Outdoor Plasma Profile CYM DM A638 10 Outdoor Plasma Wash CYM DM Plasma Speedster 5 sec color change A533 02 01 Plasma Profile CYM DM A533 02 10 Plasma Wash CYM DM A533 500 02 CTE Plasma Profile White Light Fixture A533 600 02 CTE Plasma Profile CTO Dimmer A533 510 02 CTE Plasma Wash White Light Fixture A533 610 02 CTE Plasma Wash CTO Dimmer A638 02 01 Outdoor Plasma Profile CYM DM A638 02 10 Outdoor Plasma Wash CYM DM Index accessories 4 audience iii beam optimization 7 soft edge 7 CE Declaration 18 cleaning dichroics 19 color engine 1 connections 9 contents 4 demo mode 14 15 display Blanking 10 DMX base addressing 8 connection 9 control 10 determining 8 reset 10 signal indicator 9 start channels document documentation iii ETC Component 2 features 3 freight ii installing power cord cap 4 keypad control 11 Legacy Model 2 maintenance 18 operation general 9 operation overview 9 orientation of
15. e Position Action 994 Reset Douser Home Position Action Modal functions remain in effect until another is selected Actions return to the current mode after execution Gel Match functions 901 903 and 905 925 are based on Osram HPL750 115 lamp Functions take effect after a 3 second delay k Demo Mode The SeaChanger Tungsten demo mode provides for color changing without a DMX controller attached Selection of 800 via RDM or keypad starts the demo mode The fixture will sequence through the colors in Table 4a for the SeaChanger Tungsten Profile xG or as in Table 4b for the SeaChanger Tungsten Profile DM optional patterned aluminum douser wheel below with a four second dwell time at each color Custom demo color tables are available at the time of order please contact SeaChanger Tungsten Profile for more information Table 4a SeaChanger Tungsten XG xGRB Filter Demo Sequence Sequence ROM Number Function Keypad Equivalent 1 Cyan Full 901 2 Magenta Full 902 3 Yellow Full 903 4 Red M Y xGRB 905 5 Extreme Green xGRB 906 6 Roscolux 82 Surprise Blue 907 7 Roscolux 03 Dark Bastard Amber 908 8 Roscolux 158 Deep Orange 909 9 Roscolux 45 Rose 910 10 Roscolux 60 No Color Blue 911 11 Roscolux 51 Surprise Pink 912 12 Roscolux 94 Kelly Green 913 13 Roscolux 08 Pale Gold 914 14 L 341 Plum 915 15 L 162 Bastard Amber 916 16 L 11
16. ed without an RMA number see Error Reference source not found Error Reference source not found Package Contents The SeaChanger Tungsten Color Engine ships with the following items e Safety cable e User manual found on line at http seachangeronline com technical Optional Accessories The following accessories are available from SeaChanger e Extended Yoke for down lighting or Front Of House installations e Double Clutch Friction plates on both sides of the fixture to add to overall stability e DMX Terminators to terminate the string of DMX lines to the fixtures e Factory Installed Edison Stage Pin or Twist Lock plugs e Barn Door Top Hat adapter ring Attach a 7 5 barn door or top hat to screen the light from the audience or scenery SeaChanger Tungsten Setup Overview a Installing the proper power cord cap b Attaching to on ETC Source Four c Fixture orientation d Beam adjustments e Determining DMX Base addresses f Setting the DMX start channels a Installing a Power Cord Cap Your SeaChanger Tungsten ships with a power cord that must be connected to a standard cord cap Different locations may require a different power cord cap to connect the fixture to a power source Because of the variety of power cord caps used worldwide SeaChanger Tungsten cannot make specific recommendations for the power cord cap Contact a local authority for the type of power cord cap needed The SeaChanger Tungsten has a un
17. ent mode after execution Gel Match functions 901 903 and 905 925 are based on Osram HPL750 115 lamp Functions take effect after a 3 second delay Table 3b SeaChanger Tungsten DM Optional Douser Keypad RDM Control Functions Ee Function Type 001 509 Set Fixture Base Address Modal 700 Unassigned 701 Display Orientation Normal Action 702 Display Orientation Inverted Action 800 Start Demo Mode Modal 900 All Out Clear Modal 901 Cyan Full Modal 902 Magenta Full Modal 903 Yellow Full Modal 904 All In Full Dim Modal 905 L 079 Just Blue Modal 906 L 110 Middle Rose Modal 907 L 104 Deep Amber Modal 908 L 105 Orange Modal 909 L 164 Flame Red Modal 910 L 322 Soft Green Modal 911 Roscolux 60 No Color Blue Modal 912 Roscolux 51 Surprise Pink Modal 913 Roscolux 21 Golden Amber Modal 914 Roscolux 82 Surprise Blue Modal Roscolux 04 Medium Bastard Modal 915 Amber 916 L 142 Pale Violet Modal 917 Roscolux 02 Bastard Amber Modal 918 Roscolux 46 Magenta Modal 919 Roscolux 59 Indigo Modal 920 L 136 Pale Lavender Modal 921 L 035 Light Pink Modal 922 L 158 Deep Orange Modal 923 L 248 Half Minus Green Modal 924 Roscolux 05 Rose Tint Modal 925 L 162 Bastard Amber Modal 990 Reset All Home Position Action 991 Reset Cyan Home Position Action 992 Reset Magenta Home Position Action 993 Reset Yellow Hom
18. g or cover other than that in which it is published Trademarks SeaChanger Tungsten Profile is a trademark of SeaChanger PIXELTEQ Inc Source Four is a registered trademark of Electronic Theatre Controls Inc ETC All other products and services mentioned herein are the trademarks service marks registered trademarks or registered service marks of their respective owners Limit of Liability Every effort has been made to make this manual as complete and as accurate as possible but no warranty or fitness is implied The information provided is on an as is basis SeaChanger Tungsten Profile shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this manual Important Safety and Warranty Notices Safety Information Please read all instructions prior to assembling mounting and operating this equipment Product Modification Warning SeaChanger Tungsten Profile and Tungsten Wash products are designed and manufactured to meet the requirements of United States and International safety regulations Modifications to the product could affect safety and render the product noncompliant to relevant safety standards Modification des produits d alerte SeaChanger produits sont con us et fabriqu s pour r pondre aux exigences des Etats Unis et r glementations internationales de s curit Les modifications au produit pourrait affecter la s c
19. ion Unpacking the Products Package Contents Optional Accessories SeaChanger Tungsten Setup Installing a Power Cord Cap Mounting the SeaChanger on S4 Fixture Orientation Optimizing Beam Determining a Valid DMX Base Address ON NM M ch A CONN OO OO PS PP Chapter 3 Appendix A Appendix B Numbers Index Setting the Base DMX Address Operation Overview General Operation Power and DMX Connections Tungsten Display and Control Buttons DMX Signal Indicator Display Blanking USITT DMX512 A Manufacturer ID DMX Control Reset from DMX Console Keypad Control RDM Control Demo Mode Specifications and Certifications SeaChanger Specifications RoHS CE Declaration Maintenance and Part Cleaning the SeaChanger Tungsten Dichroic Spare Parts Fixture Part Numbers 11 11 12 13 14 15 16 16 17 18 18 19 19 21 22 About This Manual This document provides you with an installation section to get your SeaChanger Tungsten Profile and or Tungsten Wash up and running Document Summary Product Related Documentation Chapter Description Chapter 1 Features and descriptions Provides a list of product features Contains instructions for unpacking installing and configuring the SeaChanger Plasma Profile and Wash Chapter2 Setup and configuration Chapter d Operation Contains instructions for using the SeaChanger Plasma Profile and Wash Appendix A Specifications and
20. iversal power supply onboard that allows for connection to a wide variety of main power sources Refer to the Specifications section for details When installing the power cord cap note that the cores in the mains lead are colored in accordance with the following code Color Function Green with Yellow stripe Ground Blue Neutral Brown Live WARNING The SeaChanger Tungsten is Class 1 equipment This equipment must be connected to an earth ground The SeaChanger Tungsten is suitable for indoor use only If the power cord becomes damaged it must be replaced by the manufacturer or a qualified person in order to avoid a hazard Maximum total color changer cable length per SeaChanger Tungsten should not exceed 600 ft 182 9 m ALERTE Le SeaChanger est de cat gorie 1 de l quipement Cet quipement doit tre connect a une prise de terre Le profil de tungstene SeaChanger est adapt pour une utilisation en int rieur uniquement Si le cordon d alimentation est endommag il doit tre remplac par le fabricant ou une personne qualifi e afin d viter un danger Couleur maximale totale par la longueur du cable changeur SeaChanger ne devrait pas d passer 600 pieds 182 9 m b Mounting the SeaChanger Tungsten on a Source Four The SeaChanger Tungsten requires no tools to install It fits between the lamp and the lens module of the Source Four Ellipsoidal fixture Perform this procedure before you connect the fi
21. link for the DMX controller There are 512 available channels on each DMX link These 512 channels are divided among all the devices on a particular link The number of channels a fixture requires is called the fixture s channel range The DMX base address assigned to a particular fixture is the first channel available to a fixture in its channel range The fixture s channel range must not overlap any other device s channel range on the link When two devices on the same DMX link have overlapping channel ranges one or both devices will be disabled or behave erratically Remember the following criteria when determining a valid base address e The base address is the number of the first channel in a consecutive block of channels assigned to an individual fixture e If you want two or more fixtures to respond to controller commands in exactly the same way you can assign them the same base address In that case those fixtures must be the same type and must share the entire channel range e A fixture can be assigned the second block of DMX channels on a link without physically being the second fixture on the link e To avoid overlapping channels place the start channel at the beginning of a range of available channels large enough to accommodate that fixture type e Every channel in the link does not need to be assigned e The channel range required for a fixture differs depending on the fixture type The SeaChanger Tungsten Profile uses a DM
22. mber A451 02 03 profile and A47402 03 wash The Legacy units have a one second color change from clear to full saturation The fixture is convection cooled and designed without cooling fans resulting in total silent operation This product is ideal for quiet venues such as Churches Theaters and Studios The Speedster snaps to color changes in 0 5 seconds and uses a 24 V power supply to drive the wheel motors as opposed to the 5 0 V supplies of the Legacy The increase in voltage requires a fan to cool the electronics cage The Speedster is ideal for Cruise Ships Casinos Night Clubs and Touring venues SeaChanger Tungsten Features SeaChanger Tungsten Profile and Wash Color Engine offer the following features Amazing color gamut provided by the xG Extreme Green multispectral filter which when used in concert with the CMY filters provides deep blues rich reds vivid greens enhanced overtones and incredible tonal balance and control High efficiency dichroic Less light loss with dichroic color than with a gel and unlike gels will never fade or wash out No interference with Source Four optics The Profile can be used with any beam angle from 5 degree to 90 degree as well as EDB lens type Smooth color mixing Includes pastel and saturated colors Installs in seconds with quick bayonet mounting to your Source Four Onboard drive electronics feature adaptive speed response algorithms giving full control over color
23. num douser wheel Table 3a SeaChanger Tungsten XG xGRB Filter Keypad RDM Control Functions a Function Type 001 509 Set Fixture Base Address Modal 700 Unassigned 701 Display Orientation Normal Action 702 Display Orientation Inverted Action 800 Start Demo Mode Modal 900 All Out Clear Modal 901 Cyan Full Modal 902 Magenta Full Modal 903 Yellow Full Modal 904 All In Full Dim Modal 905 Red M Y xGRB Full Modal 906 Green xGRB Full Modal 907 Roscolux 82 Surprise Blue Modal 908 Roscolux 03 Dark Bastard Amber Modal 909 Roscolux 158 Deep Orange Modal 910 Roscolux 45 Rose Modal 911 Roscolux 60 No Color Blue Modal 912 Roscolux 51 Surprise Pink Modal 913 Roscolux 94 Kelly Green Modal 914 Roscolux 08 Pale Gold Modal 915 L 341 Plum Modal 916 L 162 Bastard Amber Modal 917 L 113 Magenta Modal 918 L 103 Straw Modal 919 L 124 Dark Green Modal 920 L 166 Pale Red Modal 921 L 004 Medium Bastard Amber Modal 922 Roscolux 310 Daffodil Modal 923 Roscolux 46 Magenta Modal 924 Roscolux 99 Chocolate Modal 925 Roscolux 62 Booster Blue Modal 990 Reset All Home Position Action 991 Reset Cyan Home Position Action 992 Reset Magenta Home Position Action 993 Reset Yellow Home Position Action 994 Reset xGRB Home Position Action Modal functions remain in effect until another is selected Actions return to the curr
24. r the ETC Source Four fixture RoHS Restriction of Hazardous Substances SeaChanger Plasma Profile and Wash and SeaChanger Plasma Profile and Wash products comply with RoHS and do not contain any of the six banned substances lead mercury cadmium and hexavalent chromium poly brominated biphenyls PBB or polybrominated diphenyl ethers PBDE in quantities exceeding maximum concentration values RoHS Restriction des Substances Dangereuses SeaChanger et produits SeaChanger se conformer aux directives RoHS et ne contiennent aucune des six substances interdites le plomb le mercure le cadmium le chrome hexavalent les poly brom s PBB ni de polybromodiph nyl thers PBDE en quantit s n exc dant valeurs maximales de concentration Seachanger CE Declaration of Conformance We declare under our sole responsibility that the product Equipment Classification Stage Lighting Devise Equipment type Color Changer Model A451 24 SeaChanger Profile Color Engine A451 01 SeaChanger Profile Fixture A474 24 SeaChanger Wash Color Engine A474 01 SeaChanger Wash Fixture Manufactured at Ocean Thin Films Inc 8060 Bryan Dairy Road Largo Florida 33777 that this declaration relates in conformity with the following standards EN61000 6 3 2001 EN55022 FCC part15 EN61000 3 2 1995 EN61000 3 3 1994 EN61000 6 1 2001 EN61000 4 2 EN61000 4 3 EN61000 4 4 EN61000 4 5 EN 610004 6 EN61000 4 6 EN6100
25. rchaser will pay all shipping charges Items under warranty shall have return shipping paid by the manufacturer only in the continental United States Under no circumstances will freight collect shipments be accepted Prepaid shipping does not include rush expediting such as airfreight Airfreight can be sent customer collect in the continental United States REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER SEACHANGER MAKES NO WARRANTIES EXPRESS OR IMPLIED WITH RESPECT TO ANY PRODUCT AND SEACHANGER SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Warranty is void if the product is misused damaged modified in any way or for unauthorized repairs or parts This warranty gives you specific legal rights you may also have other rights which vary from state to state Table of Important Safety and Warranty Notices Safety Information Product Modification Warning Warranty Information Limited Warranty Returning an Item Under Warranty for Repair Freight Table of Contents Chapter 1 Chapter 2 About This Manual Document Summary Product Related Documentation Upgrades Features and Descriptions Tungsten Profile and Wash Color Engine Tungsten Profile Description Tungsten Wash Description ETC S4 Component Standard Wheel Set and Studio Dichroic wheel set Tungsten Legacy and Speedster Models Seachanger Tungsten Features Setup and Configurat
26. ten Seachanger do not go to full saturation and is designed to allow 5 white light to pass through the patterning at the most saturated point This small amount of white light allows for the mixing of large variety of pastel color combinations When the Go wheel which looks green to the eye is added to the CYM mix it can add elements of RGB for hexachromic color mixing The CYM and Xg will extend the typical color palette out beyond conventional dichroic color mixing systems The Studio Dichroic wheel set is pattern such that the CYM wheels are extended to 100 saturation but shortens the length of the patterning of the wheels thereby reducing some of the varieties of pastel colors The green Xg wheels for each wheel set are the same with 98 saturation In general t he Studio Dichroic set will result in bigger blues reds and purples at the expense of the subtle pastel color pallet while the 95 saturated standard wheels set will offer a larger all around color pallet but will not have the very extreme saturated reds and blues Most applications for the Studio Dichroic wheel set are for Cruise Ships Casinos Tour and musicals The standard set is favored by theaters and churches with some opting for both wheel sets Legacy and Speedster Models of Tungsten Fixtures The Seachanger Tungsten Profile and Wash fixtures are available in two speeds The Legacy part number A451 01 03 profile and A 474 01 03 and the faster Speedster part nu
27. ungsten Profile Attaches between the rear housing assembly and the front barrel assembly of the Source Four and does not interfere with the gate area You can still use patterns irises gobo changers and all the usual accessories with your Source Four fixture There are two CYM wheel sets for the profile Standard with the CYM wheels at 95 saturation producing more pastel theatrical colors and Studio Dichroic with the CYM wheels at 100 saturation producing more vibrant reds blues and greens for night clubs and Casinos The Xg extreme green wheel is the same in both wheel set options The Seachanger Tungsten Wash The Seachanger Tungsten Wash utilizes a reflector housing assembly from an ETC Source Four 750 The Wash is intended for a soft edge beam profile that closely assimilates an ETC Par 64 fixture The beam angle is manually adjustable for a FOV Field of view from 20 to 70 degrees ETC Components Rear Reflector Housing Lamp Cap Front End Assembly Yoke and FOV Barrels are not included and must be supplied by the user Standard Wheel Set and Studio Dichroic Wheel Set All Seachangers have four dichroic wheel positions with three of those wheels being CYM In addition to the CYM wheels in the Tungsten Profile Seachanger the 4 wheel position is generally an extreme green wheel or Xg wheel a dimmer or custom wheel can also be substituted if desired The patterned wheel set look like tiger stripes in the standard tungs
28. ur fixture Insert the front barrel assembly onto the front locking ring of the SeaChanger Tungsten Profile engaging the barrel assembly into the locking ring channels Adjust the front barrel assembly to the desired orientation and tighten the thumbscrew and Philips set screw to lock the front barrel assembly to the SeaChanger Tungsten Profile Mount the unit using safety cable at the mounting location Attaching Tungsten Wash to Source Four reflector housing 1 Remove the Source Four from the yoke assembly setting aside the yoke bolts washers and Friction handle 2 Using the same screws attach the Yoke with washers and bolts from step 1 to the SeaChanger Tungsten Wash as shown in the figure below Replace the friction handle and adjust the yoke to the desired orientation 3 Remove the rear reflector housing assembly from the Source Four ellipsoidal fixture by loosening the thumbscrew and the Philips set screw 4 Rotate the barrel assembly until it releases from the mounting tabs located in the rear housing assembly 5 Insert the Source Four rear housing assembly to the Seachanger Wash fixture by aligning the mounting tabs into the rear locking ring of the SeaChanger Tungsten Wash Rotate the rear housing until the Source Four mounting tabs are captured in the SeaChanger Tungsten Wash locking ring channels Tighten the thumbscrew and Philips set screw to lock the module onto the Source Four fixture c Fixture Orientation
29. urit et rendre le produit non conforme aux normes de s curit applicables Warranty Information Limited Warranty Unless otherwise stated your product unit is covered by a one year parts and labor limited warranty Dichroic filters are not guaranteed against breakage or scratches to coating It is the owner s responsibility to furnish receipts or invoices for verification of purchase date and dealer or distributor If purchase date cannot be provided date of manufacture will be used to determine warranty period Returning an Item under Warranty for Repair It is necessary to obtain a Return Material Authorization RMA number from your dealer or point of purchase BEFORE any units are returned for repair The manufacturer will make the final determination as to whether or not the unit is covered by warranty All product units or parts returned to SeaChanger must be packaged ina suitable manner to ensure the protection of such product units or parts This packaging must be clearly and prominently marked to indicate that the package contains returned product units or parts and must also display its RMA number Accompany all returned product units or parts with a written explanation of the alleged problem or malfunction Ship returned product units or parts to SeaChanger 8060 Bryan Dairy Road Largo Florida 33777 Note Freight damage claims are invalid for fixtures shipped in non factory boxes and packing materials Freight The pu
30. xture to power WARNING AVOID CONTACT BY PERSONS AND MATERIALS USE ONLY AN ETC SOURCE FOUR REFLECTOR HOUSING FITTED WITH LAMPS NOT EXCEEDING 750 WATTS MAXIMUM ALERTE CHALEUR INTENSE EVITER LE CONTACT PAR DES PERSONNES ET DES MATERIAUX PAS POUR UN USAGE RESIDENTIEL UTILISER UNIQUEMENT BOITIER DE REFLECTEUR DE LAETC SOURCE FOUR EQUIPES DE LAMPES NE DEPASSANT PAS 750 WATTS MAXIMUM Installing Tungsten Profile in ETC Source 4 To install a SeaChanger Tungsten Profile Color Engine in a Source Four ellipsoidal fixture 1 2 Remove the Source Four from the yoke assembly setting aside the screws to use in Step 2 Using the same screws attach the SeaChanger Tungsten Profile as shown in the figure below Adjust the SeaChanger Tungsten Profile to the desired orientation Remove the front barrel assembly of the Source Four ellipsoidal fixture by loosening the thumbscrew and the Philips set screw located above and beneath the lens barrel Rotate the barrel assembly until it releases from the mounting tabs located in the rear housing assembly Insert the SeaChanger Tungsten Profile into the Source Four rear housing assembly by aligning the mounting tabs into the rear locking ring of the SeaChanger Tungsten Profile You must rotate the rear housing until the Source Four mounting tabs are captured in the SeaChanger Tungsten Profile locking ring channels Tighten the thumbscrew and Philips set screw to lock the module onto the Source Fo
Download Pdf Manuals
Related Search