PRO`S PRO SX-01
Contents
1. from dust grease moisture and any type of heat Clean the dust and other dirt with a soft cloth or brush Water should never come Inside the machine Do not use liquid cleansers abrasive cleaners or aerosol cleaners Use fine emery cloth to remove the wax buildup from the jaws of the clamps and the string gripper Do not uses sandpaper to remove the wax buildup 1t will destroy the special finishing Do not lubricate the tracks of the turntable Do not use penetrating oils to clean or to lubricate 10 Check the clamps often to be sure that they hold the string properly I not adjust them as shown before 11 Reset the tension setting to 10 kilograms after stringing 8 Troubleshooting The power light does not shine and the electronic part does not do anything Be sure the power switch is in on position Check that the power cord is properly installed Check the fuse Turn off the power switch and unplug the power cord from the wall outlet before checking the fuse The fuse housing is next to the power switch Check the wall outlet with another electronic equipment Page 8 The string clamp does not hold the string e Clean the Jaws of the string clamp e Adjust the clamp on the top by turning the wheel and or using an allen wrench for Vernier adjustment The string slips through the string gripper e Clean the string gripper like described before The clamp does not move smoothly or can not2. Electronic SX 01 Stringing Machine User s Manual Attention Please read this manual carefully before operating with the machine Keep it properly for the aftersales service Page 1 Catalogue 1 Attentions 1 1 Operating attentions Iue urus Insr asas au ua a aa 3 12 Safeusingattentions u ur o an UI uuu aaa 3 2 Unpacking and inspection 2 1 Components 4 2 2 Inspection 3 Operating Instructions Ir L 5 4 Mounting aracket rr cure aaa 6 5 Insertastring sss aa 7 6 Adjusting the base of the swivel clamp 7 7 Maintamce ee eee eeaeeeeeeeeee 8 8 Troubleshooting ccc ecceeeceee 8 9 Service Guide __ U UU I aaa 9 10 Calibration 10 Page 2 Safety precautions Following are fatal informations for your safety please observe strictly Warning mark Any information in this manual with a warning mark must be abided by strictly otherwise there will be danger of the personal safety or could lead to a significant accident EI Forbidden mark Any information in this manual with a forbidden mark must be abided by strictly otherwise there will be danger of the personal safety or could lead to damage of the machine 1 1 Warning Do use 220v AC power and the provided cable and plug Please make sure the power match the machine in the play court Do not disassemble or change the machine voluntarily otherwise it will damage the machine or cause serious accidents N Do not use the machine c
3. ace the four K shaped side supports into the hole of the side support arms in the far outer hole for tennis rackets in the other hole for badminton and squash Now place the racket in the middle of the stringing machine Ensure that the two swivel clamps can reach all of the racket area for stringing Never apply excessive force or over tighten the mounting stock locking knobs this will damage the parts Tighten now the side support arms and the mounting stock but be careful not to do this too heavily that the racket will not be deformed Page 6 5 How to put the string into the tension system First place the string over the small reel and then around the big one and place it into the slot and hold the string down Then push the button to 1 and the machine starts pulling until it has the right tension 6 How to use the Swivel Clamp System When the clamp falls back into the clamp base it opens automatically Alternatively the quick release can be opened by applying pressure on the release button A significant improvement to conventional systems is that the clamp base can be adjusted with a rotary screw The adjustment with an Allen key is no longer necessary Page 7 7 Maintenance ON CA W 8 2 The Electronic SX 01 stringing machine is adjusted and calibrated before shipment Working is easy and relatively maintenance free Keep the stringing machine always at a dry and safe place Keep it away
4. be fixed e Clean the tracks of the turntable e Adjust the swivel clamp base per instruction The tension pulling is not correct e Calibrate the machine e Is the string not fixed in the clamp e Is the clamp base moving 10 Service Guide Service notice If there is problem during the using time please call our service hotline or send an email Please do provide us bar code or detailed order consignee and the date of purchase Page 9 11 Calibration The machine is calibrated with an electronic Tension calibrator if you have only a mechanic one please be sure that it is not too old otherwise the spring inside will give you wrong results 1 Set the tension to 30 kg 2 press the KG LB continual until the LCD show 0 00kg 3 fix a tension calibrator Tension Calibrator Page 1U 4 press right button for starting stringing the line 5 after pressing this button the display switches to 20 5kg now push the right button again as long as the multimeter tension calibrator is 30kgs then press the KG LB button and OK loose the line finish no matter what is shown on the display of the engine Page 11
5. lose to volatile or flammable gas N Do keep away from heat prevent putting the machine under the sun for long time avoiding the plastic and rubber parts become aged Z Do contact with local service provider or manufacturer If the machine has an unusual situation for example big noise strong smog and leakage please cut the power immediately N Do unplug the power plus when the machine is not in use or renew parts 1 2 Forbidden N Do not let the kids play with the machine or power equipment N Do not touch the inner parts when the machine is operating or it will cause an accident N Do not let the kids operate the machine when cleaning up interior of the machine in order to avoid damaging the machine or causing any danger N Do not operate the power or machine switch with barefoot or wet hands Do not move it during working Do not clean the surface of the machine with volatile wet cloth Do not putting it aside in moist or other bad environment Do not pressing the ascending and descending pounds function in the same time otherwise it will cause damage to the machine Do not placing the cable in high temperature or beside the heating Page 3 Unpacking and inspection The machine is delivered ready assembled 2 1 Components 4x T054 racket frame support EE E a er 2 x T071 clamp Ix Cor AC power cable Set of ra Allen wrench 2 2 Unpack the machine carefully and inspect the Electro
6. nic SX 01 stringing machine for any obvious damage Check if all parts are included in the carton If any item is missing or damaged contact your delivery agent and your sales representative Retain the original packaging materials for the event that reshipping is required Page 4 3 Operating Instructions 1 Place the machine on a table or a stand foot 2 On the back side of the electronic tension there is a switch which should be in the ON position for normal operation 3 Turn the power on and a green light flashes and the tension strength appears on the LED display 4 Select the tension scale in kilograms or pounds The machine is always shipped set to kilogram The switch for it is between both knob for setting kg Ib the tension 5 5 For setting the tension use the 2 knobs for rising and reducing the tension The tension can be set in 0 5 kg steps t Rising the tension t Reducing the tension 6 The stringing machine has 2 positions Machine pulls to the selected tension Machine moves back to the starting position to release the string Page 5 7 If the engine doesn t stop pulling automatically press the backwards 8 After stringing turn the machine off button 9 Turn the tension on the display down to 10 kilogram the tension in the machine should be as low as possible in the time of not stringing 4 Fixing of the Racket Loosen both mounting stocks pl
Download Pdf Manuals
Related Search