digital timer 884 series
Contents
1. a FWT di Tommaso Commonara ENNWNT digital timer 884 series vi verceii4 00182 Roma Italia Tel 39 06 70392126 Fax 39 06 7012486 fluid and water technology Operation manual Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it BUILT IN ELECTRONIC TIMERS Series 884 Electronic built in timers with day and week programming 1 channel allows a precise minute switch off single days or block programming e g Monday to Friday Safety Instruction o Always turn off the power during repair work o 220 240V life threatening voltage o The Diehl 884 built in timer should only be installed by a person with the relevant qualifications Operating and visual elements Abb 1 Operating and visual elements Display with time switch points 2 Slide switch to set the operation mode AUTO The timer will switch on and off according to the selected programme I Permanently on ae permanently override O Permanently off 3 Slide switch to set the time and switching times RUN Operator mode h Input actual time and set mode Programme mode 4 Press down the button marked F to set the 16 switching points When the program mode is set the light symbol will appear on the right hand side of the display screen If the switching points 1 3 5 7 9 11 13 15 are activated light symbol will appear on the display These positions are the ON time start positions 5 Press down the button marked 1 to 72. block programming of one type e g 12345 block programming of one type e g 12345 d ON program next OFF program block programming daily programming e ON program next OFF program Programmed time ON e g at 9 00 on Wed OFF e g at 8 59 on Wed Time to turn on is later than time to turn off of the same day f ON program next OFF program Programmed time ON e g at 9 00 on Wed OFF e g at 9 00 on Wed Time to turn on is the same as time to turn off of the same day 8 Correct program entry The following program entries are acceptable a ON program next OFF program daily programming block programming b ON program next OFF program daily programming daily programming c ON program next OFF program block programming of one type e g 12345 block programming of same type e g 12345 d ON program next OFF program Programmed time ON e g at 8 59 on Wed OFF e g at 9 00 on Wed Figure 4 Wiring diagram for pump cable and utility connections 1 Cut the mains cable to size 2 Dismantle the connector and then slip the individual pieces over the cable making sure they are in the right order 3 Peel a short length of the cable sheath and bare the constituent leads all as shown in the drawing above Connect the cable leads to the connector respecting the above pin colour pattern 5 Reassemble the connec
3. to set the days of the week and block programming e g 1 5 Monday to Friday 1 6 Monday to Saturday 6 7 Saturday to Sunday 1 7 Monday to Sunday OJ g A FWT di Tommaso Commonara ENNWNT d Ig ital timer 884 Se rieS via vercelli 4 00182 Roma Italia d Tel 39 06 70392126 Fax 39 06 7012486 fluid and water technology Operation manual Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it 6 Press down and release the button marked to set the hours for actual time of day and switching times Short press of the button market results in the timer counting one up Pressing down the button marked for longer than 3 seconds results in fast forward counting 7 QR Press down the reset button in order to erase all switching times and actual time of day 8 HIN Press down the button marked MN to set the minutes for actual time of the day and switching times Short press of the button marked MN results in the timer counting one up Pressing down the button marked for longer than 3 seconds results in fast forward counting 9 6 Skip Function or soft override By pressing down the Skip button the timer will be switched into the opposite functional mode For example the relay is switched on By pressing down the button marked skip the timer will be switched off Programming Before programming a reset is required It can be done by pressing down the reset button with a thin instru
4. 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it ELECTRONIC DIGITAL TIMER 884 SERIES USER MANUAL Operation Function Description Series 884 1 Power up conditions a Upon rest CR you will see that the display blinks Make sure slide switch is in RUN position before reset 1234567 b Upon rest if the slide switch is at P you will see error message EEE Push slide switch to RUN position to clear the error message 1234567 c Push slide switch to position and you will see a stable display 1234567 d Push slide switch to RUN position and you will see a stable display with the colon blinking 1234567 e Push slide switch to E position and you will see a stable display 1234567 a FWT di Tommaso Commonara ENNWNT digital timer 884 series vi verceii4 00182 Roma Italia Tel 39 06 70392126 Fax 39 06 7012486 fluid and water technology Operation manual Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it 2 Manual Control Slide switch to I position Lamp symbol appear on LCD Output switches to ON and remains ON Slide switch to O position Lamp symbol disappear on LCD Output switches to OFF and remains OFF Slide switch back to AUTO position Program control is resumed The status of the output depends on previous programs you have set 3 Set time function description For example to set the time to
5. 34567 k press to set hour 19 press HR button to advance setting from 0 to 19 I press HIN button to set min 53 press ih button to advance setting from 00 to 53 19 5317 press program button P to advance to program no 18 1234567 O 00 18 n press 4 2 day button to set day all day press a7 button to cycle day setting from NONE 7 1 6 1 5 6 7 1 6 and to all day 1 7 The fast advance feature similar to that shown in 3 a also exists 1234567 ahhh hh he 0 00 18 o press to set hour 23 press button to advance setting from 0 to 23 1234567 he he te he he he 23 00 18 p press HIN button to set min 53 press HIN button to advance setting from 00 to 53 1234567 press program button P again to review program settings Q 8 FWT di Tommaso Commonara ENNWNT digital timer 884 S ri S viavercelli 4 00182 Roma Italia Tel 39 06 70392126 fluid and water technology Operation manual e E S info fwtsystems it Rev 03 07 04 Www fwtsystems it 5 Skip function setting and operation Manual Control Set slide switch at RUN position Press skip Ge button to skip program control soft override The skip function brings forward just the actual status from ON to OFF and vice versa continuing with the normal set program at the next ON OFF A cross over an arrow symbol skip symbol Ge appears on the LCD to indicate this s
6. Wed 3 16 pm with the factory present at 24 hr version First slide switch to set time position a Set calendar day press day button 7 to advance the triangular day indicator from 7 Sunday to 3 Wednesday When the button is stressed the triangle advances one step If the button is not released in 1 second the triangle continues to advance at the rate of 1 step per second until release 1234567 b Set hour minute press hour and MN buttons to advance hour minute setting to 15 16 When the button is pressed the hour minute setting will advance one step If the button is not released in 2 seconds the setting will continue to advance at a fast rate of 8 steps per second 1234567 15 16 4 Set program function description For example to set program no 3 to switch on at p 03 on Wed program no 4 to switch off at 11 04 on Wed program no 17 to switch on at 19 53 for all day and program no 18 to switch off at 23 54 for all day First slide switch to set program position then a advance program selection to program no 3 with button P button advances program number 1 step at each activation Program 3 is initially cleared with no triangular day indicator and the setting time will initially be 0 00 1234567 b press day button to set day 3 press a7 button to advance day setting from NONE 7 3 The fast advance feature during set time mode also exists 1234567 8 FWT
7. di Tommaso Commonara ENNWNT digital timer 884 SerieS vi verceii 4 00182 Roma Italia Tel 39 06 70392126 Fax 39 06 7012486 Operation manual Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it c press to set hour 9 press button to advance setting from 0 to 9 fluid and water technology 1234567 d press HIN button to set min 3 press HIN button to advance setting from 00 to 03 1234567 e press program button P to advance to program no 4 1234567 f press 7 day button to set day 3 press 7 button to advance day setting from NONE 7 3 The fast advance feature during set time mode also exists 1234567 0 004 g press to set hour 11 press HR button to advance setting from 0 to 11 1234567 11 004 h press HIN button to set min 04 press MN button to advance setting from 00 to 04 1234567 A 11 044 i press program button to advance to program no 17 1234567 8 FWT di Tommaso Commonara ENNWNT digital timer 884 SerieS vi verceii 4 00182 Roma Italia Tel 39 06 70392126 Fax 39 06 7012486 Operation manual Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it fluid and water technology j press 7 day button to set day all day press a7 button to advance day setting from NONE 7 1 6 1 5 6 7 1 6 and to all day 1 7 The fast advance feature similar to that shown in 3 a also exists 12
8. itching programme Block programming e g 1 2 3 4 5 Next switching off programme Block programming of a different kind e g 1 2 3 4 5 6 d Switching programme Block programming Next switching off programme Daily programming e Switching programme Programmed switching on times e g Wednesday 9 00 H Next switching off programme Programmed switching off times e g Wednesday 8 59 H f Switching programme Programmed switching on times e g Wednesday 9 00 H Next switching off programme Programmed switching off times e g Wednesday 9 00 H Technical Data o Day and week programming possibilities o 16 switching possibilities 8 x ON 8 x OFF By block programming there is a total of 56 different programming possibilities o Shortest time between two switching points is 1 minutes fe Programmed memory of up to 5 year due to Lithium battery o Mains voltage 220 240V life threatening voltage o switch rating Ohmic 10 A 250 V o inductive 4 A 250 V ind o Ambient temperature range 14 F bis 132 F T55 Guarantee There is a 12 month guarantee for any of the components of the Diehl 884 built in timer Any damage to the 884 series which occurs due to mishandling is under no circumstances covered by a 12 month guarantee FWT di Tommaso Commonara ENNWNT digital timer 884 SerieS vi verceii 4 00182 Roma Italia Tel 39 06 70392126 Fax 39 06 7012486 fluid and water technology Operation manual Mobile
9. l reliability will be enhanced if it is correctly used and subjected to regular maintenance WARNING Any intervention or repair in the interior of the pump must be carried out by qualified and authorized personnel The makers decline all responsibility for the consequences of failure to respect this rule 11
10. ment The slide switch must be set in RUN mode The display will begin to blink Setting the time and da Slide the switch into position Setting the time can be done by pressing down the and MN buttons When the buttons are held down for a period longer than three seconds the fast forward setting is activated Setting the days of the week is done by pressing down the button marked e g 1 Monday 7 Sunday An arrow will appear on the screen indicating the day of the week 1234567 After completing the above programme set the slide switch to RUN and the time of day will be activated a g l FWT di Tommaso Commonara EVYVVJ T d Ig ital timer 884 Series via verceni 4 00182 Roma Italia Tel 39 06 70392126 ion r nal Fax 39 06 7012486 fluid and water technology Operation manual Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it Setting the time and da Set the Slide switch into position P By pressing down the buttons a7 it is possible to set the day Likewise block programming procedure is also possible The next programming procedure can be recalled by pressing down the button marked CF There are also 16 switching points in total which can be stored on memory 8x ON 8 x OFF The number and symbol on the display screen indicated which mode has been selected 1234567 a 9 00 ON 1234567 10 00 2 OFF After the input on the switching times it is necessary to slide
11. r erroneous or unreasonable use of the unit Use of electrical equipment always implies observance of some basic rules In particular 1 do not touch the equipment with wet or damp hands or feet 2 do not operate the pump with bare feet Example swimming pool equipment 3 do not leave the equipment exposed to the action of the atmospheric agents 4 do not allow the pump to be used without supervision by children or incompetent people Before carrying out any maintenance or cleaning operation disconnect the unit from the power supply by means of the circuit breaker In case of breakdown or improper functioning of the controller switch it off but do not touch Contact our technical assistance for any necessary repairs and insist on the use of original spares Failure to respect this condition could render the unit unsafe for use When you decide to make no further use of an installed controller make sure to disconnect it from the power supply The electrical installation to which the controller is connected must comply with the standards and good practice rule in force in the country under consideration The pump complies with EEC directives No 89 336 regarding electromagnetic compatibility and No 73 23 regarding low voltages as also the subsequent modification No 93 68 Maximum environmental operating temperature 40 C N B The controller has been constructed in accordance with best practice Both its life and it electrical and mechanica
12. tatus 1234567 Press and release the skip button again to disable the skip function if it was enabled The skip symbol disappears to reflect the cancellation Output status will then resume to the auto output status determined by those valid program settings The skip function will be disabled automatically upon the next programmes ON OFF will be reached 1234567 15 16 E Skip function may be selected only at RUN mode Skip function may be enables disables with the skip button E Skip indicator 6 shows whether skip function is enabled 6 Error message displa There are two types of error display One of the examples is shown in selection 1b This happens when an attempt is made to set a program before the time is initialised first by sliding the switch to set time mode upon reset The other type of error display is for indicating a program entry error EVY T digital timer 884 series fluid and water technology 7 FWT di Tommaso Commonara Via Vercelli 4 00182 Roma Italia Tel 39 06 70392126 Fax 39 06 7012486 Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it Operation manual Invalid program entry The following program entries could invoke this error message a ON program next OFF program daily or block programming no entry or NONE b ON program next OFF program no entry or NONE daily or block programming c ON program next OFF program
13. the AUTO and RUN switches into the correct positions in order to activate the programmed sequence X gt Skip Function Set the slide switch into RUN mode By pressing down the skip button 6 the timer will automatically be switched into the opposite operational mode For example the timer is in operational mode ON Therefore by pressing down the Skip button 6 the operational mode will be reversed When the skip function is activated the skip symbol x will appear on the display Pressing down the skip button again will cancel the skip function Switching times changes and correlation Slide the switch to the position marked P It is possible to use the button marked P to recall the information which has been saved To erase a programmed switch point it is necessary to press down the buttons which are marked as 9 and 4 on the second page of the operation manual This process will delete the switching points FT isital timer 884 series fluid and water technology Operation manual FWT di Tommaso Commonara Via Vercelli 4 00182 Roma Italia Tel 39 06 70392126 Fax 39 06 7012486 Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it Programming mistakes Possible programming failures a Switching programme Daily or block programming Next switching off programme No input b Switching programme No input Next switching off programme Daily or block programming c Sw
14. tor BLUE GREEN 4 BROWN 10 x g FWT di Tommaso Commonara EVVJ T d Ig ital timer 884 Series via verceni 4 00182 Roma Italia 4 Tel 39 06 70392126 fluid and water technology ration ma Fax 39 06 7012486 Operation manual Mobile 39 335 6013103 info fwtsystems it Rev 03 07 04 Www fwtsystems it Further hints and warnings Please read the warning notices given in this section very carefully because they provide important information regarding safety in installation use and maintenance of the controller Keep this manual in a safe place so that it will always be available for further consultation After unpacking the unit make sure it is completely sound In case of doubt do not use the controller and contact qualified personnel The packing materials especially bags made of plastics polystyrene etc should be kept out of the reach of children they constitute potential sources of danger Before you connect the controller make sure that the voltage ratings etc correspond to your particular power supply You will find these values on the rating plate attached to the pump The controller should be used only for the purpose for which it has been expressly designed namely the controlling and measuring physical chemical values Any different use is to be considered improper and therefore dangerous The makers cannot be held responsible for damage deriving from imprope
Download Pdf Manuals
Related Search