User`s Manual - Field Wireless
Contents
1. YOKOGAWA ENGINEERING ASIA PTE LTD 5 Bedok South Road Singapore 469270 SINGAPORE Phone 65 6241 9933 Fax 65 6241 2606 YOKOGAWA INDIA LTD Plot No 96 Electronic City Complex Hosur Road Bangalore 560 100 INDIA Phone 91 80 4158 6000 Fax 91 80 2852 1442 YOKOGAWA AUSTRALIA PTY LTD Tower A 112 118 Talavera Road Macquarie Park NSW 2113 AUSTRALIA Phone 61 2 8870 1100 Fax 61 2 8870 1111 YOKOGAWA MIDDLE EAST amp AFRICA B S C C P O Box 10070 Manama Building 577 Road 2516 Busaiteen 225 Muharraq BAHRAIN Phone 973 17 358100 Fax 973 17 336100 Apr 14 1 Introduction This manual describes how to use the FN110 Field Wireless Communication Module hereafter simply referred to as FN110 FN110 enables various sensors with digital communication interface to be operated in field wireless network by converting input output of sensor to wireless transmission based on the wireless communication standard ISA100 11a Your FN110 was precisely calibrated at the factory before shipment To ensure both safety and efficiency please read this manual carefully before you operate the FN110 E Regarding This Manual e This manual should be provided to the end user The contents of this manual are subject to change without prior notice All rights reserved No part of this manual may be reproduced in any form without Yokogawa s written permission Yokogawa makes no warranty of any kind with regard to this manua2. 608 SN Eul64 ae SUTRA 2 9 4 8 VDC 60mA EA O YOKOGAWA okro 10 8750 Yokogawa Electric Corporation JAPAN F01 ai Figure 2 1 Nameplate E Bundled items Manual IM 01W03B01 01EN Open Source Software license term F9092QA Protection cap optional specifications The remote antenna cable is not included 2 2 Transport To prevent damage while in transit leave the FN110 in the original shipping container until it reaches the installation site 2 3 Storage When storing this product observe the following precautions 1 Choose a storage location that satisfies the following requirements Alocation that is not exposed to rain or water Alocation subject to a minimum of vibration or impact The temperature and humidity limits refer to 5 1 Specifications 2 If at all possible store the FN110 in factory shipped condition that is in the original shipping container 3 Installation 3 1 Precautions Before installing refer to the User s Manual of the device to be connected to the FN110 For additional information on the ambient conditions allowed at the installation location refer to 5 1 Specifications 3 2 Mounting The installation procedure is as follows 1 Check the orientation of the pins insert FN110 into the connector on the device 2 Tighten the lock nut to a torque of 1 2 N m Removal is the reverse of the above F02 ai
3. Figure 3 1 Installation of FN110 and Sealing of the Connector To install FN110 with remote antenna cable follow the procedure below 1 Assemble the mounting bracket and fix it on a 50A 2 inch pipe 2 Connect the FN110 and the device the dedicated remote antenna cable Tighten the connector of the remote antenna cable with a torque of 1 2 N m The minimum bend radius should be more than 100mm 3 Protect the connectors of the FN110 and remote antenna cable as necessary 4 Fix the remote antenna cable to an appropriate structure to protect the cable from the vibration wind and so on The minimum bending radius for fixing in the state maintained for a long period should be more than 100 mm 5 Fix the FN110 to the mounting bracket IM 01W03B01 01EN l FN110 holder bolt FN110 FN110 mounting bracket FN110 holder Remote antenna cable Bracket fastening bot 9 It U bolt nut Sx Spring washer Bracket fastening nut 2 inch pipe mounting bracket U bolt 2 inch pipe F03 ai Figure 3 2 Horizontal Pipe Mounting of FN110 Bracket fastening nut Spring washer U bolt nut FN110 mounting bracket 2 inch pipe FN110 holder bolt 2 inch pipe mounting bracket Bracket fastening bolt Remote antenna cable FN110 holder Eoi Figure 3 3 Vertical Pipe Mounting of FN110 F05 ai Figure 3 4 Sealing of the Remote Antenna Cable A IMPORTANT The connector is shippe
4. N for the latest information 5 1 Specifications Communication Protocol ISA100 11a IEEE802 15 4 Data Rate 250 kbps Frequency 2400 2483 5 MHz license free ISM band Radio Security AES 128 bit RF Transmitter Power 12 dBm eirp Antenna 2 dBi Omni directional Power Supply Voltage 2 9 4 8V Consumption Current Max 60 mA Update Period 1 to 3600 s Depends on module to connect this product Refer to the General Specifications of the products that are connected to this product Digital Communication for FN series Communication Mode Half duplex communication RS485 compliant Communication Speed 9600 bps Communication Distance Max 20 m dedicated cable Diagnostic Functions Power failures wired communication failures firmware internal errors memory errors abnormal temperature Software Download Function Software download function enables you to update wireless field device software via ISA100 Wireless communication Ambient Temperature Limits Operating 40 to 85 C altitude up to 3000 m Storage 40 to 85 C Ambient Humidity Limits Operating 0 to 100 RH non condensation Storage 0 to 100 RH non condensation Ambient Temperature Gradient Operating 10 C h or less Storage 20 C h or less Vibration Resistance 0 21 mm P P 10 60 Hz 3 G 60 2 kHz Shock Resistance 50 G 11 ms Grounding Ground through the mating of the metal shell Please ensure that the ground terminal is connected to an
5. SSS User s Manual FN110 Field Wireless Communication Module IM 01W03B01 01EN 2nd Edition Dec 2014 KP All Rights Reserved Copyright 2014 Yokogawa Electric Corporation YOKOGAWA IM 01W03B01 01EN 2nd Edition YOKOGAWA YOKOGAWA ELECTRIC CORPORATION Headquarters 2 9 32 Nakacho Musashino shi Tokyo 180 8750 JAPAN Phone 81 422 52 5555 Branch Sales Offices Osaka Nagoya Hiroshima Kurashiki Fukuoka Kitakyusyu YOKOGAWA CORPORATION OF AMERICA Head Office 12530 West Airport Blvd Sugar Land Texas 77478 USA Phone 1 281 340 3800 Fax 1 281 340 3838 Georgia Office 2 Dart Road Newnan Georgia 30265 USA Phone 1 800 888 6400 1 770 253 7000 Fax 1 770 254 0928 YOKOGAWA AMERICA DO SUL LTDA Praca Acapulco 31 Santo Amaro Sao Paulo SP BRAZIL CEP 04675 190 Phone 55 11 5681 2400 Fax 55 11 5681 4434 YOKOGAWA EUROPE B V Euroweg 2 3825 HD Amersfoort THE NETHERLANDS Phone 31 88 4641000 Fax 31 88 4641111 YOKOGAWA ELECTRIC CIS LTD Grokholskiy per 13 Building 2 4th Floor 129090 Moscow RUSSIA Phone 7 495 737 7868 Fax 7 495 737 7869 YOKOGAWA CHINA CO LTD 3F Tower D Cartelo Crocodile Building No 568 West Tianshan Road Shanghai 200335 CHINA Phone 86 21 62396262 Fax 86 21 62387866 YOKOGAWA ELECTRIC KOREA CO LTD Yokogawa B D Yangpyeong dong 4 Ga 21 Seonyu ro 45 gil Yeongdeungpo gu Seoul 150 866 KOREA Phone 82 2 2628 6000 Fax 82 2 2628 6400
6. appropriate ground Weight 100g 5 2 Regulatory Compliance Statements This product satisfies the following standards Please confirm that an installation region fulfills an applicable standard If additional regulatory information and approvals are required contact a Yokogawa representative Telecommunication Compliance MIC Identification Japan Applied to a wireless module that incorporates Construction Design Attestation Number 006 000202 FCC Approval United States Part 15B 15C This device complies with part 15 of the FCC Rules Operation in subject to following two conditions 1 This device may not cause harmful interface and 2 this device must accept any interference received including interference that may cause undesired operation FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment A NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential
7. area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Co located This transmitter must not be co located or operated in conjunction with any other antenna or transmitter RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency RF Exposure Guidelines This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person s body IC Approval Canada RSS Gen This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device French Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement RSS 102 This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS 102 of the IC radio frequency RF Exposure rules This equipme
8. ct our service office A IMPORTANT e Although this product has been designed to resist high frequency electrical noise if a radio transceiver is used near this product or its external wiring this product may be affected by high frequency noise pickup To test this start out from a distance of several meters and slowly approach this product with the transceiver while observing the measurement loop for noise effects Thereafter use the transceiver outside the range where the noise effects were first observed 1 2 Warranty The warranty shall cover the period noted on the quotation presented to the purchaser at the time of purchase Problems occurring during the warranty period shall basically be repaired free of change If any problems are experienced with this product the customer should contact the Yokogawa representative from which this product was purchased or the nearest Yokogawa office Ifa problem arises with this product please inform us of the nature of the problem and the circumstances under which it developed including the model specification and serial number Any diagrams data and other information you can include in your communication will also be helpful The party responsible for the cost of fixing the problem shall be determined by Yokogawa following an investigation conducted by Yokogawa E The purchaser shall bear the responsibility for repair costs even during the warranty period if the malfunction is due
9. d with a dust cap Keep the cap attached until the installation to protect the connector The cap should be stored so that you can use it again when you detach FN110 In an extremely wet condition use the optional water proof cap A CAUTION Before installing turn off the equipment to be installed e When installing secure FN110 by tightening the lock nut Tightening by screwing the housing instead of the lock nut may cause failure such as cable disconnection Use the dedicated remote antenna cable provided by Yokogawa as accessories for FN110 The remote antenna cable and other cables should not be bundled together To maintain a good connection between the modules protect the connector from the corrosive atmosphere by the following treatment 1 Clean the connection to be protected 2 Wind the butyl rubber self bonding tape around the connection See the manual of the tape about the winding 3 To protect the butyl rubber self bonding tape from the environment such as ultraviolet rays and so on wind vinyl tape or a vinyl type self bonding tape on it 4 When the tape is necessary prepare appropriate tape for the installing environment Do not cover the nameplate by the tapes 4 Operation FN110 is used with FN series product e g FN310 Field Wireless Multi Protocol Module For the usage of FN110 refer to the User s Manual of the device to be connected to FN110 5 General Specifications Please refer to GS 01W03B01 01E
10. e describes the degree to which a solid liquid or gas which deteriorates dielectric strength or surface resistivity is adhering 2 applies to normal indoor atmosphere Normally only non conductive pollution occurs Occasionally however temporary conductivity caused by condensation must be expected 2 Installation Category Overvoltage category Installation category describes a number which defines a transient overvoltage condition It implies the regulation for impulse with stand voltage I applies to electrical equipment which is supplied from the circuit when appropriate transient overvoltage control means interfaces are provided Degrees of Protection IP66 IP66 rating applies when the connector is properly tightened Explosion Proof Types TIIS FM United States or Canada ATEX IECEx approvals under pending 5 3 Model and Suffix Codes Refer to the General Specification GS 01W03B01 01EN 5 4 External Dimensions and Pin Assignment Unit mm approx inch Pin Signal 1 Not Connected Signal Ground Power Supply Transmit Receive Data positive a Ri wo nrp Transmit Receive Data negative 21 0 83 23 0 91 F06 ai Revision Record Title FN110 Field Wireless Communication Module Manual No IM 01W03B01 01EN C an e O e f oan 2nd Dec 2014 1 2 1 Add Bundled items 2 5 2 Add CSA Safety Requirements Modify Explosion Proo
11. l including but not limited to implied warranty of merchantability and fitness for a particular purpose If any question arises or errors are found or if any information is missing from this manual please inform the nearest Yokogawa sales office e The specifications covered by this manual are limited to those for the standard type under the specified model number break down and do not cover custom made instruments e Please note that changes in the specifications construction or component parts of the instrument may not immediately be reflected in this manual at the time of change provided that postponement of revisions will not cause difficulty to the user from a functional or performance standpoint E Safety Protection and Modification of this Product In order to protect the operator product and system controlled by the product observe the safety precautions described in this manual If users handle contrary to these instructions we cannot guarantee the safety e Modification of the product is strictly prohibited The following safety symbols are used in this manual A caution Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or physical damage It may also be used to alert against unsafe practices IMPORTANT Indicates that operating the hardware or software in this manner may damage it or lead to system failure A NOTE Draws attention to information e
12. nt should be installed and operated keeping the radiator at least 20 cm or more away from person s body excluding extremities hands wrists feet and ankles French Cet quipement est conforme aux limites d exposition aux rayonnements nonc es pour un environnement non contr l et respecte les r gles d exposition aux fr quences radio lectriques RF CNR 102 de I lC Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps a l exception des extr mit s mains poignets pieds et chevilles R amp TTE Directive EU Countries We Yokogawa Electric Corporation hereby declare that this equipment model FN110 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The EU declaration of conformity for R amp TTE for this product can be found at http Awww yokogawa com fld The Authorized Representative for this product in the EEA is Yokogawa Europe B V Euroweg 2 3825 HD Amersfoort THE NETHERLANDS CE Conformity C Radio Spectrum EN 300 328 EMC EN 301 489 1 EN301 489 17 EN61326 1 Class A Table 2 For use in industrial locations EN55011 Class A A CAUTION This instrument is a Class A product and it is designed for use in the industrial environment Please use this instrument in the industrial environment only Safety EN61010 1 Indoor Outdoor use EN62479 1 Pollution Degree 2 Pollution degre
13. ssential for understanding the operation and features 1 1 Radio Wave A IMPORTANT This product is equipped with a wireless module which is designated as a certification of construction type as a wireless facility for 2 4 GHz band low power data communication system of the Radio Act Refer to 5 2 Regulatory Compliance Statements for detail Due to the designated certification of construction type users may be subject to legal punishment in case of disassembling or modifying this product RF Transmitter power eirp The factory default settings of RF transmitter power is 12dBm current consumption 50mA or less The maximum settings of RF transmitter power is 14dBm current consumption 60mA or less e Microwave ovens and other industrial scientific and medical equipment as well as local wireless stations license required and specific low power wireless stations license not required for identifying mobile objects used in the production line of a factory use the same frequency band as this product Prevent interference with other wireless stations e Check that local wireless stations and specific low power wireless stations are not being used in the vicinity before using this product e If this product causes radio interference in a local wireless station used for identifying mobile objects change the working frequency or stop the emission of radio waves immediately For details on how to prevent radio interference conta
14. t Types IM 01W03B01 01EN P2
15. to Improper and or inadequate maintenance by the purchaser Malfunction or damage due to a failure to handle use or store this product in accordance with the design specifications Use of this product in question in a location not conforming to the standards specified by Yokogawa or due to improper maintenance of the installation location Failure or damage due to modification or repair by any party except Yokogawa or an approved representative of Yokogawa e Malfunction or damage from improper relocation of this product in question after delivery Reason of force majeure such as fires earthquakes storms floods thunder lightening or other natural disasters or disturbances riots warfare or radioactive contamination 2 Notes on Handling The FN110 is fully factory tested before shipment When the FN110 is delivered check the appearance for damage 2 1 Check the Model and Specifications The model name and specifications are written on the nameplate attached to the housing Verify that the specification indicated in the Model and Suffix Code in General Specifications GS 01W03B01 01EN is in compliance with the specifications written on the order sheet Manual number omitting the language code at the end is printed on the nameplate Check the delivery by reference to the following bundled item list MODEL rNiio Cid Wig o LT A READ IM 01W03B01 01 FCC ID SGJ WFCO11 IC 8999A WICO10 eC 172
Download Pdf Manuals
Related Search