TitanBeam™ 7R Manual
Contents
1. 16CH Lamp Control Lamp Control 17CH Pan Tilt Time 18CH Color Time 19CH Beam Time 20CH Gobo Time 6 1 Colors 6 2 Strobe Standard 16Bit Channel Value Function mode mode function 0 3 Close 4 103 Strobe Slow Fast 104 107 Open 108 207 Pulse Slow Fast 2 Strobe 308 212 Open 213 225 Random Strobe Slow 226 238 Random Strobe Medium 239 251 Random Strobe Fast 252 255 Open 6 3 Dimmer Standard 16Bit Channel Value Function mode mode function 3 3 Dimmer 0 255 0 100 Standard 16Bit Channel Value Function mode mode function 0 9 Open 10 19 red 20 29 Yellow 30 39 Blue 40 49 Green 50 59 Hot Pink 60 69 Aqua Marine 70 79 Orange 80 89 Electric White 90 99 Warm White 1 1 Color 100 109 Pink 110 119 Lime Green 120 129 Ivory 130 139 Cool White 140 149 Purple 150 159 Color Scroll Fast 196 199 Color Scroll Medium 200 202 Color Scroll Slow 6 4 DMX Channels amp Values Standard 16Bit Channel Value Function mode mode function 175 Gobo 1 Shake Fast 176 Gobo 2 Shake Slow 180 Gobo 2 Shake Fast 4 4 Static Gobo Panes lle tivatdtauceneestos 246 Gobo 16 Shake Slow 250 Gobo 16 Shake Fas2. 20 CH17 20 Speed control See the channel table Off Pan Revers On Off Tilt Revers On Pan Tilt Off Swap On Swap faders XY coder On Pan amp tilt motor correction Off NO DMX Retain Display keep 5 5 Manuel Tab On the home screen touch the manual tab scroll up and down to get to your desired field press ok to enter and make changes It is always a good idea to reset fixture before using the settings in this manual mode Display On Off On turns off display after 60 sec Lamp On n Light turns on with fixture Off Bulb turns on through DMX controller Linear Color Of On Default Click OK button and confirm load default Settings settings 5 4 Information Tab Option Instruction Firmware Current software version Version Total Fixture Touch the system tab use the Up amp Down arrows Hours scroll to total fixture hours Partial Fixture Touch the system tab use the Up amp Down arrows Hours scroll to partial fixture hours Total Lamp Hours Touch the system tab use the Up amp Down arrows scroll to total lamp hours System Error If the red ERR led turns on there is an operational error The details on the error can be viewed in the systems error field under the systems tab Option Instruction Touch the manual tab press the Up or Reset Down arrow scroll to reset pr
3. GER DANGER DANGER Warning Warning Warning Warning Hazardous Safety hazard Refer to Fire Burn hazard Risk of Risk of voltage Risk of manual before hazard Hot surface not eye injury hand injury Risk of severe or severe injury installing powering touch Do Safety glasses Safety gloves lethal electric shock or death or servicing nat touch must be worn must be worn ag a RX B R E d a c Luminaires not For indoor Do not direct Do not Replace any Minimum Rated suitable for direct use only lens to sun actuate during cracked distance from maximum mounting on normally ray or strong operation protective lighted objects ambient flammable surfaces light shield metres temperature sultableonly for mountingon non combustible surfaces A Protection against electrical shock All electrical connections must be performed by a qualified person with technical certificate Make sure that the mains power supply you use is up to local construc tion and electronic code regulation the over load protection reliable earthing is essential Each fixture must be grounded correctly and be installed according to related regulation Disconnect the fixture from AC power before removing or installing any cover or part including the lamp and fuses and when notin use Do not expose the fixture to rain or moisture Protection against burning or fire Please do not install the fixture onto combustible surface Do not attempt to b
4. TitanBeam 7R User Manual o y N q K j 230W Moving Head Beam Introduction Thank you for purchasing the OMEZ TitanBeam 7R This moving head fixture characterized by its exceptional bright light beam is a new product in the Titan Line This light weight fixture is CE compliant and has a perfect combination of advanced electronic controlling technology with standard DMX 512 control Programing is a breeze on the fixture s touch screen panel OMEZ TitanBeam 7R has a 230 watt discharge lamp with reflector that projects a high quality long range beam of light With 5 high quality step motors you can pan tilt and focus with fast Smooth precision OMEZ TitanBeam 7R features one color wheel with 14 colors plus open and one gobo wheel with 17 static patterns Added to the 7R is the pulse feature a steady longer and smoother shutter effect This small light weight fixture is designed for easy transport for mobile DJ s VJ s KJ s and Production companies OMEZ TitanBeam 7R is the industry standard in T V reality shows Arenas Concert halls Banquet halls Performing arts theaters Nightclubs and Entertainment venues Omez Guaranty This TitanBeam 7R has met all quality control requirements when tested in our factory and is known to be in perfect condition when shipped to our warehouse in El Monte California In order to ensure the safe operation of this TitanBeam 7R it is absolutely nec
5. ess ok and confirm Color 0 255 Press the manual tab use the Up or Shutter Strobe 0 255 Down arrows to scroll to desired Dimmer 0 255 field press the Ok make changes Gobo 0 255 then press Ok once more to store Prism 0 255 new changes Prism Rotate 0 255 Macro Function 0 255 Frost 0 255 Focus 0 255 Pan 0 255 Pan Fine 0 255 Tilt 0 255 Tilt Fine 0 255 Pan Tilt Speed 0 255 Gobo speed 0 255 Manual On Lamp control Off 5 6 Advance Tab On the home screen touch on the advance tab press the up and down tab continues twice then ok 6 DMX Channels Option Instruction Sensor Monitor Scroll Up or Down press ok to enter field Reset Calibration Scroll Up or Down press ok to enter field Zero Point Correction Scroll Up or Down press ok to enter field Lamp Life Hours Scroll Up or Down press ok to enter field Clear lamp Hours Scroll Up or Down press ok to enter field Channel Standard mode 16CH 16Bit mode 20CH 1CH Color Wheel Color Wheel 2CH Shutter Strobe Shutter Strobe 3CH Dimmer Dimmer 4CH Gobo Gobo 5CH Prism Prism 6CH Prism Rotate Prism Rotate 7CH Prism Macro Prism Macro 8CH Frost Frost 9CH Focus Focus 10CH Pan Pan 11CH Pan Fine Pan Fine 12CH Tilt Tilt 13CH Tilt Fine Tilt Fine 14CH Pan Tilt Speed Pan Tilt Speed 15CH Reset Reset
6. essary for the end user to follow the safety instructions and warnings notes written in this user manual Contents Introduction Omez Promise ccccccccccccccccccccceel Safety information aiyisea uence vipa KEEN CENETA Included in package er ee eee ee er Features E E Control panel E E T DMX Channels serana idene aa e aO Installation EEE Cleaning amp maintenance eesssssssscccesssssesccesocsoeeeed Before plugging in fixture Please read manual 2 Safety Information WARNING Read the safety precautions in this section before installing powering operating or servicing this product After receiving the fixture please unpack and check if there is any damage due to transportation If any obvious damage or flaw is found do not put it into use and co ntact the distributor or manufacturer as soon as possible A A amp 40 C B A This fixture is intended for professional use only When operating the fixture attentions should be drawn to fire electrical shock hazards ultraviolet radiation lamp shattering or lethal injuries caused by fall Read this User Mannual before mounting and ennergizing the fixture Observe the safety guideline and notice the warnings both in this User Mannual and on the fixture Yet any safety concerns not covered hereby contact the distributor or service hot line Protection against over heat The fixture is intended for indoor application its protection ratin
7. from reach by unauthorized personal is always recommended Before mounting the fixture make sure that the area you are using can hold a minimum load of 5x the Fixtures weight You must always use a secondary safety attachment such as a safety cable The TitanBeam 7R is fully operational in two install positions hanging upside down on a truss or by setting it on a flat level surface Always make sure that all fixture are kept at least 0 5m away from any flammable materials 8 Cleaning amp Maintanance For best results TitanBeam 7R requires routine cleaning and maintenance Excessive dust smoke fluid and particulate buildup will degrade the performance and will cause the fixture to overheat The damage from this is not is not covered in the manufacture warranty Always make sure you unplug the fixture before opening any covers for cleaning Optical components should be cleaned carefully and do not use any harmful solvents to avoid damage Remember to keep all air vents clean and free from clutter that will prevents constant air flow When resetting fixture please allow an average of 20 sec for the fixture to reset all sensors and motors Fixture will continue where it left off The lamp will stay on so there is no cool off wait time Always remember if the light bulb turns of at any time during operation there is a 5 10 minute cool down period before bulb ignites A Omez Lighting reserves the right to make changes and or improve
8. g is IP20 The fixture should be kept dry and avoid working in presence of moisture over heat or heavy smokes The natural working temperature should be lower than 40 degrees If the ambient temperature exceeds 40 degrees please stop operating the unit immediately Protection against explosion Shields lenses and ultraviolet screens must be replaced if they have become visible damaged to such an extent that their effectiveness is impaired Replace the lamp immediately if it becomes visually deformed damaged or in any way defected Protection against injury due to falls Do not lift or carry the fixture alone To inspect that the structure and the truss hooks are in good condition and can bear about 10 times the weight of the fixture Ensure the cover and all riggings are securely fastened safety wire is necessary to use as a secondary attachment Block access below the working area and work from a stable platform while installing servicing or moving the fixture Protection against ultraviolet radiation Prolonged exposure to an unshielded discharged lamp can cause eye and skin burns Do not stare directly into the light output Never look at an exposed lamp while itis lit Never operate the fixture with missing or damaged lenses and or covers Change the damaged head lens shields or covers immediately The following symbols are used to identify important safety information on the product and in this manual AAAAAA A DAN
9. ments in design upon its products without any obligation to include these changes to any products theretofore manufactured OMEZ
10. t 251 Gobo 17 Shake Slow 255 Gobo 17 Shake Fast 0 127 No Prism 5 5 Prism 128 255 Prism 0 127 No Rotation 128 Fast Rotation 190 Slow Rotation 6 6 Rotating 191 192 STOP prism 193 Slow Rotation 255 Fast Rotation 7 7 Effect 0 255 Prism Macro Standard 16Bit Channel Value Function mode mode function 0 4 Open 5 9 Gobo 1 10 14 Gobo 2 15 19 Gobo 3 20 24 Gobo 4 25 29 Gobo 5 30 34 Gobo 6 35 39 Gobo 7 40 44 Gobo 8 45 49 Gobo 9 50 54 Gobo 10 55 59 Gobo 11 60 64 Gobo 12 4 4 Static Gobo 65 69 Gobo 13 70 74 Gobo 14 75 79 Gobo 15 80 84 Gobo 16 85 89 Gobo 17 90 Gobo Rotate Fast 129 Gobo Rotate Slow 130 134 STOP 135 Gobo Rotate Slow 170 Gobo Rotate Fast Gobo Shake Slow Speed Standard 16Bit Channel Value Function mode mode function 0 127 No Frost 8 8 Frost 128 255 Frost 0 Focus 0 9 9 Focus sia 255 Focus 100 10 10 Pan 0 255 0 540 11 11 Pan Fine 0 255 Adjustment 12 12 Tilt 0 255 0 270 13 13 Tilt fine 0 255 Adjustment 14 14 Motor Speed 0 255 Pan Tilt Speed 0 25 Unused Range 26 76 Effect Reset 15 15 Reset 77 127 Pan Tilt Reset 128 255 Complete Reset 16 16 Lamp control 0 9 Lamp On 10 100 Lamp Off 101 255 Unused 17 Pan tilt 0 255 Fast slow Time 18 Color time 0 255 Fast 19 Beam time 0 255 Fast 20 Gobo time 0 255 Fast 7 Installation Mounting the fixture in areas away
11. unctions Left arrow and Right arrow exit current screen push twice it will take you back to home screen Up amp Down arrows always you to scroll through current screen OK button enter or save Example below 1 If the current display is not on the main screen press the left arrow or right arrow button twice to get back to the home screen 2 Inthe main screen press the up arrow or Down arrow to scroll through the tabs on the screen to make a selection 3 Press the OK button to enter selected page In the Settings tab press the up arrow or down arrow button to select DMX address Press the OK button to enter dmx addressing Press the up arrow or down arrow to modify the DMX address 7 Press the OK button to save change A quicker process would be to use the touch screen 5 2 Home Screen The top 2 right tabs on the screen are used for language and screen rotation 5 3 Settings Tab Option Instruction slave mode Receive a DMX signal from Operation DMX controller or master fixture Mode master mode Auto run1 2 3 4 send DMX signal to slave Auto Note You must let the fixture cycle on before entering auto mode Press the OK button to enter DMX address DMX 1 512 mode use the Up amp Down arrows to scroll Address through DMX channels press ok to save new value Channel 16 CH17 20 No function Mode
12. ypass the thermostat switch or fuse Replace defective fuses with specified ratings only Keep flammable materials far away from the fixture Minimum distance from the flammable materials is 0 5m The maximum working temperature of the exterior surface under a thermally steady state is 85 C Please don t touch the moving head during movement Do not illuminate surfaces within 10 meters of the fixture Prohibit pro jecting object in short distance Ensure a minimum clearance of 0 1m around the cooling fans and ve ntilations Do not place any filter or other object onto the optical lens Allow the fixture to cool for at least 15 minutes before transit Do not revise the fixture or install any parts not from Guangzhou CHAI YI LIGHT Co Ltd 3 Included In Package This box includes items listed below Accessories QTY UNIT User manual 1 PCS Warranty card 1 PCS Suspension fasteners 2 SET DMX cable 1 PCS 4 Features Modes 16 20 Channels Lamp Type 230w YODN Bulb Color Temperature 8000K Luminance 63900 20m Beam Angle 4 0 100 Linear Dimming Strobe Speed 1 13 FPS 14 Dichroic Colors 17 Static Gobos 8 Facet Rotating Prism Pan Tilt 540 630 270 8 bit 16 bit LED Touch Screen Display Power Supply 100 240V 50 60Hz Heat Emission 0 08kw h Power Consumption 335W Size 336 315 512mm Net weight 20 5kg CE amp RoHS Compliant 5 Control panel 5 1 Panel Instructions F
Download Pdf Manuals
Related Search