User manual
Contents
1. Keep enough space around the unit for ventilation Slots and openings on the monitor should not be blocked During flashes of lightning or cracks of thunder or when the system is not used for a pog nime unplug the system power supply to protect the unit from lightening or power surges I INSTALLATION color dome camera Before installation make sure you are familiar with this product s special features and proper operating technique Yin V This manual explains the installation and operating method for the Stick the guire pattern on the wall or ceiling Guide Pattern Fix the camera to a ceiling using two screws Dome Base After fixing it adjust its pan base and tilt base properly After adjust them fixed the dome cover Dome Cover DIMENSIONS mm Dome 0805 A I SPECIFICATIONS Signal System Scanning TE H Image FES S N Ratio Video Output Level Focus Min Illumination F1 2 30IRE AGC Max White Balance Input Output Connector Supplied Voltage Dimensions xH I COMPOSITION Owner s Manual Dome Camera ver 1002E P N 3810 0083C HIGH RESOLUTION NTSC PAL NTSC 2 1 Interlace NTSC 15 734 kHz PAL 15 625 kHz NTSC 59 94 Hz PAL 50 Hz 1 3 inch High Sensitivity CCD 768 H x494 V 752 H x582 V 510 H x492 V 50dB Min AGC off 600 TV Lines 1 0 Vp p 75 Ohms composite Fixed Lens f 3 8mm 6 0mm Selectable Pin Hole2. Lens Manual Internal 0 05 Lux NTSC 1 60 120 000 Sec PAL 1 50 120 000 Sec Auto Auto Power Red Jack Video Yellow Jack 3 Vp p max 45dB typ 12VDC 10V 15V Less than 180mA 89 5 x 63mm Approx 157g Changes in this user manual can be made without notice in order to improve the product quality Guide Pattern Of CONNECTION Video Output Power GND OH x Recommendable Power Supply 12VDC Over 0 3A Power Adapter Terminal Color Insert coin to the side hole and remove the dome cover by twist coin P 1 Video Output Yellow 2 Powerinput Ra o o o o o EJ Audio Output White Option Available on select model s only CCD Colotamerg Digital DSP color jnwie 1 3 High Sensitivity CCD ap LENS Fixed CCD COLOR Pin Hole AWB Auto White AGC Auto Gain DSP Digital Signal Balance Control Processor I TROUBLESHOOTING If you have trouble operating your camera refer to the following If the guidelines do not enable you to solve the problem contact an authorized technician e Check the power source for the monitor and camera and ensure that the voltage and polarity are properly connected and being supplied correctly The image does not appear on the screen e Check if the lens is stained If dirty The image on the clean the lens with a soft clean cloth screen is dim e Adjust the Back Focus of the lens again The camera
3. USER INFORMATION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Explanation of two Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE All the warnings and instructions of this manual should be followed Remove the plug from the outlet before cleaning Do not use liquid aerosol detergents Use water damped cloth for cleaning To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture Do not place anything on top of the unit that might spill or fall into it Do not attempt to service this unit yourself as opening or removing covers may you to dangerous voltage or other hazards Please refer all servicing to qualified service personnel
4. does not Check if you have connected the camera work properly the to a proper power source and If there is surface of the camera no problem with the power turn the unit case is hot and a off immediately and seek assistance from black line appears on our Customer Service department the screen The screen blinks alot Check if the camera is pointed toward the sun or a fluorescent lamp e Adjust the angle or location of the camera if too much light is coming into the screen
Download Pdf Manuals
Related Search