AX11652 - Quick Access Biometric Rifle Safe
Contents
1. Failure to follow these warnings could result in serious injury or death op CED NW A Foie Actual model may vary A Initialization Button G Logo Plate and Emergency B Battery Compartment Key Access C Bolts H Handle D Fingerprint Scanner External Battery Pack E Indicator Lights batteries not included F Wake Up Button J External Battery Access GETTING STARTED 1 Remove Emergency Keys from accessory package 2 To expose the Emergency Key access remove Logo Plate G screws with provided tool 3 Insert Emergency Key into key access push and turn counter clockwise 4 Turn Handle H clockwise to open the safe 5 Continue with INSTALL BATTERIES INSTALL BATTERIES 1 Remove Battery Compartment B cover 2 Insert 4 AA batteries and restore battery cover 3 Continue with FINGERPRITN REGISTRATION FINGERPRINT REGISTRATION IMPORTANT The safe is in either Pre registered mode or Factory Default mode test safe to determine factory settings below Pre registered mode Safe can NOT be opened with any fingerprint s Factory Default mode Safe can be opened with ANY fingerprint s 1 With the safe door open press and release Initialization Button A 2 Immediately place a finger on the Fingerprint Scanner D Hold finger still 1 beep will be heard recognizing the fingerprint followed by 2 consecutive beeps Remove finger Registration is complete Suc2. B cover 7 All fingerprints stored in the safe have been deleted NOTE The safe is in Factory Default mode ANY fingerprint can open the safe 8 Continue with FINGERPRINT REGISTRATION and TEST NON REGISTERED FINGERPRINTS LOW BATTERY WARNING 1 When the door is closed and 3 repetitive beeps are heard and Indicator Lights E flash red it indicates the batteries are low 2 Replace batteries immediately Open safe remove Battery Compartment B cover and all 4 AA batteries Insert 4 new AA batteries and restore Battery Compartment B cover NOTE All registered fingerprints remain stored CARE AND MAINTENANCE To maximize the security and performance of the safe keep Fingerprint Scanner D clean use a dry cloth to remove any smudges or prints off the Fingerprint Scanner after each use Test registered fingerprints every 6 months Keep liquids away from the control panel Spills on the control panel will cause damage and possibly electric shock Secure safe in a proper area to prevent from falling and causing damage or injury DO NOT disassemble the product For all repairs contact BARSKA Customer Service DO NOT use chemicals or cleaning agents to clean the safe MOUNTING INSTRUCTIONS The safe must be mounted to a wall or floor Be aware of the load bearing Failure to do so can result in personal injury and or damage to property Use appropriate tools when performing work and always use eye protec
3. BARSKA User s Manual for Biometric Safe Read all instructions before using this safe WARNING New Safe is in either Pre registered mode or Factory Default mode ANY fingerprint can open the safe Only a successfully registered Fingerprint s can terminate Factory Default mode Register at least two different fingerprints and test a few times before closing the safe door Test with a non registered fingerprint If the safe opens the safe is still in Factory Default mode Avoid leaving safe door open and unattended it will allow unauthorized individuals to add their fingerprints and or reprogram the safe gaining full access to the safe and the contents Test the Emergency Keys and store them in a secure place NOT inside of the safe To maximize the security and performance of the safe test registered fingerprints every 6 months Initialization button cover must be restored after every use If user resets the safe to Factory Default mode ANY fingerprint can open the safe Test and make sure the safe works properly before mounting Mount the safe before use because the safe has a small base with a heavy door and will tip forward if not properly mounted Keep children away from safe they should not play with or around the safe at anytime Children at play could accidentally get locked inside the safe or accidentally pull on the safe door causing safe to tip over if not properly mounted
4. cessful Registration Registration is successful when a total of 3 beeps are heard Unsuccessful Registration 2 short beeps will be heard repeat registration process again 3 To register another fingerprint repeat steps 1 2 4 Continue with TEST NON REGISTERED FINGERPRINTS TEST NON REGISTERED FINGERPRINTS 1 Test multiple Non Registered fingerprints Close safe door turn Handle H counter clockwise to lock the safe Press and release Wake Up Button F Place a non registered finger on the Fingerprint Scanner D Turn Handle H clockwise the door should not open If the door opens with a non registered fingerprint registration was unsuccessful the safe is still in Factory Default mode Repeat steps under FINGERPRINT REGISTRATION and test multiple non registered fingerprints 2 Test a Registered fingerprint With door closed press and release Wake Up Button F Place a registered finger on the Fingerprint Scanner D Turn Handle H clockwise the door should open Registration was successful if it only opened with registered fingerprint s CLOSE OPEN SAFE DOOR CLOSE Close safe door turn Handle H counter clockwise to lock the safe OPEN Press and release Wake Up Button F Place a registered finger on Fingerprint Scanner D Turn Handle H clockwise to open the safe 3 13 See reverse side for more information BC282 BEEP SOUND OPTIONS Beep OFF Press and HOLD the Initialization Butt
5. on A 20 30 seconds until the Indicator Lights E flash green once RELEASE the Initialization Button Beep ON Press and HOLD the Initialization Button A 20 30 seconds until the Indicator Lights E flash green followed by 1 beep RELEASE the Initialization Button OPEN SAFE WITH EMERGENCY KEY 1 To expose the Emergency Key access remove Logo Plate G screws with provided tool 2 Insert Emergency Key into key access push and turn key counter clockwise and turn Handle H clockwise to open the safe NOTE Store Emergency Keys in a secure place NOT inside of the safe OPEN SAFE WITH EXTERNAL BATTERY PACK Use this option when internal batteries are low 1 Insert 4 AA batteries into External Battery Pack I 2 Plug into External Battery Access J 3 Press and release Wake Up Button F Place a registered finger on Fingerprint Scanner D Turn Handle H clockwise to open the safe DELETE ALL STORED FINGERPRINTS RESET TO FACTORY DEFAULT MODE 1 Open safe remove Battery Compartment B cover and all 4 AA batteries 2 Press and release Wake Up Button F a few times until no beeps are heard 3 Press and HOLD the Initialization Button A Re insert batteries on the 4th battery you will hear 1 beep followed by 2 consecutive beeps indicating safe is in Factory Default mode 4 RELEASE Initialization Button A 5 Repeat steps 1 3 if a total of 3 beeps are not heard 6 Restore Battery Compartment
6. tion Mounting Holes Wall Mounting Do not mount the safe without anchoring to the wall Find the studs in the wall at your desired location Most studs are 16 inches or 24 inches apart Check the wall for concealed wires or pipes Actual model may vary Measure the location of the pre set drill holes mark their exact position onto the wall ensuring that the studs or anything else behind will not interfere Drill the appropriate size holes for the anchors you are using Carefully press the anchor into the holes at this time Mount the safe by running screws from inside of the safe and securing to anchors ensure the safe is mounted securely Floor Mounting Use proper drill tools depending on the type of floor you are mounting the safe wood tile or concrete Measure the location of the pre set drill holes mark their exact position onto the floor Drill the appropriate size holes for the anchors you are using Carefully press the anchor into the holes at this time Mount the safe by running screws from inside of the safe and securing to anchors ensure the safe is mounted securely
Download Pdf Manuals
Related Search