User Manual User Manual
Contents
1. 14 Do not place or store combustibles on or near the wrapping station 15 Insure that the plug has good ground connection 16 When unplugging wrapping station pull on the plug Do not pull on the cord 17 This wrapping station was designed for commercial use only WD Caution Hot Surfaces Avoid Contact To provide continued protection against electric shock connect only to properly grounded outlets Do not attempt to repair or replace any parts other than the replacement parts listed in these instructions Improper repair or replacement may result in electrical hazards Do not attempt to repair or replace any parts other than the replacement parts listed in these instructions Improper repair or replacement may result in electrical hazards and will void the warranty EQUIPMENT VANTCO User Manual Wrapping Station 177WM18 PLASTIC CAPS WING NUT ROLL FILM ROLL BEARING BLOCK G CUT OFF BAR 5000565 COVER PLATE M TUR r MA POLL BAR 3 SHOWN FLIPPED UP TE F LO N C O WE g FILM ROLL BAR 5000553 TEFLON COVER 5000553 FILM ROLL BAR HOT PLATE ASSEMBLY 956 COVER PLATE 5000569 FUSE 50001 48 POWER CORD CUT OFF BAR 5000565 C BASE VIEW CUT OUT TO SHOW SWITCH BASE VIEW CUT QUI RED POWER LIGHT TO SHOWLIGHT ON OFF SWITCH Replace2. This warranty does not apply to and Avantco is not responsible for any warranty claims made on products sold or used outside of the United States
3. not spray cleaners or liquids onto any electrical components STRIKE Attack tough grease oil and carbon with this ready to use cleaner and NOBLE degreaser Its unique formula is designed to clean concrete machinery cremicarine Cleaner Degrossor engines floors walls and more Servicing The Unit e This wrapping station should only be serviced by trained personnel Unplug the wrapping station before servicing Do not attempt to repair or replace any parts other than the replacement parts listed in these instructions Improper repair or replacement may result in electrical hazards and will void the warranty Fuse Replacement 1 Unplug the wrapping station before servicing 2 Situate the wrapping station on a stable surface so that the back of wrapping station is accessible 3 Turn the fuse holder cap counterclockwise to loosen until it is released from the fuse holder receptacle The fuse will be attached to the cap 4 Remove the fuse from the fuse holder cap by pulling gently 5 Replace fuse with only type 6D 1 amp fuse part 5000148 6 Insert new fuse into fuse holder cap 7 Insert fuse holder cap with fuse into the fuse cap receptacle 8 Turn the fuse holder cap clockwise to tighten until it is hand tight 9 Situate the wrapping station into normal operating position on a stable surface 10 Plug the wrapping station into a properly grounded outlet User Manual Aico Wiring Diagram OUTLET P
4. EQUIPMENT WANTCO User Manual Single Roll Film Wrapping Station Models 17 7WM18 09 2015 Please read and keep these instructions Indoor use only EQUIPMENT User Manual VANTCO Important Safeguards Save These Instructions When using electrical appliances basic safety should always be followed Read all instructions before operating cleaning or servicing this wrapping station To protect against risk of electrical shock do not place cord plug or base in water or other liquids Do not use outdoors Close supervision is necessary when any appliance is used near children The wrapping station must be placed on a steady table Unplug the wrapping station when not in use and before cleaning or servicing Avoid contact with moving parts Do not operate wrapping station if it has malfunctioned or has been dropped or damaged Call our toll free customer support service number for information or examination of a faulty unit that may require repair or an adjustment 9 Do not operate wrapping station if power cord or plug shows evidence of damage 10 Do not operate if Hot Plate or Cut Off Bar temperatures exceed 340 F or if smoke is detected 11 Be aware of power cord location Do not let cord rest on or touch hot surfaces Do not allow cord to hang freely over table or counter 12 Keep body parts and clothing away from heating elements 13 Do not touch or operate switches or cords with wet hands
5. LUG AC CHASSIS GROUND Ow i FUSE B ON OFF SWITCH W 2 LAMP B B W AN THERMOSTAT R eo C2 R HOT PLATE e HEATING ELEMENT CUT OFF BAR CLR Technical Specifications Power 115VAC 60HZ 750W e Max Temperature 340 F 171 C Hot Bar Knife power 100W Unit Dimensions 25 9 x 22 5 x 4 7 EQUIPMENT VANTCO User Manual Limited Warranty All equipment which is sold under Avantco trademark and used for commercial purpose is warranted against defects in materials and workmanship The warranty runs for 6 months from the date of original installation and is for the benefit of the original purchaser only All other Warranties Expressed or Implied Statutory or Otherwise including Without Limitation any implied Warranty of Merchantability or Fitness for Purposes are excluded The Seller shall in no event be liable for direct indirect or consequential damages in connection with Avantco commercial products This warranty is not effective if damage occurs as a result of an accident carelessness improper installation lack of proper setup lack of supervision when required or if the equipment is installed or operated in any manner contrary to the installation and operation instructions Work performed by unauthorized personnel or unauthorized service agencies voids this Warranty
6. ment Parts 5000148 FUSE 5000565 CUT OFF BAR ASSEMBLY 5000553 TEFLON COVER 5000569 HOT PLATE ASSEMBLY EQUIPMENT User Manual VANTCO Operating Instructions This appliance is designed for wrapping fruits vegetables fish meat cold food etc 1 To load film place film roll onto film roll bearing blocks tighten the wing nuts and put the plastic caps onto threaded ends 2 Flip cover plate upward 3 Route the film between cover plate and film retainer rod See Film Loading Diagram 4 Insert the power cord plug into a properly grounded outlet 5 Turn the main switch on and the red indicator lamp will light up 6 Turn the thermostat to set the desired temperature 7 Allow 5 10 minutes for the unit to pre heat 8 Place food onto the cover plate 9 Draw out film and cover food 10 Use the Cut Off Bar to cut film 11 Flip cover plate with food onto hot plate 12 Allow 3 5 seconds for food to be completely sealed Film Loading Diagram PLASTIC CAPS FILMA ROLL WING NUTS FILM ROLL BEARING BLOCK FILAA COVER PLATE CUTOFF ROD FILM RETAINER ROD HOT PLATE CONTROL BOX FILA A EQUIPMENT VANTCO User Manual Cleaning The Unit e Unplug the wrapping station before cleaning and or servicing When Cut Off Bar and or hot plate becomes dirty clean with a cotton cloth Do not use metal or other abrasives Do not immerse the wrapping station in water or other liquids Do
Download Pdf Manuals
Related Search