User manual
Contents
1. from the device as doing so will void the warranty Only use the device for its intended purpose All other uses may lead to short circuits burns electroshocks lamp explosion crash etc Using the device in an unauthorised way will void the warranty Front amp Back Panel Description four outputs 230Vac 4A strobe output 1A POWER switch ten DIP switches put the switches in the correct position in order to install the desired address FUNCTION A CH1 test button FUNCTION A CH2 test button FUNCTION A CH3 test button FUNCTION A CH4 test button FUNCTION B Speed up FUNCTION A STROBE test button FUNCTION B Speed down FUNC use this button to select the desired function The B functions mentioned above do not work when the DMX function is activated LED indicators for channels 1 through 4 LED indicator for strobe light DMX input indicator DMX input DMX output or throughput when the device is connected in parallel with other power packs LPTDX424E 2 GB OUTPUT Use a cable with a 5 pin connector to connect the source of the DMX signal with the DMX input of this device When using several LPTDX424E s connect the output of the first DMX power pack with the input of the next DMX power pack It is possible to connect a max of 12 DMX power packs in parallel 512 separate channels 6 Chase Pattern and Channel Testing There are two options when no device is connecte2. 1 Introduction CE E H0 POWER te Puter Thank you for buying the LPTDX424E Please read the manual carefully before bringing this device into service The LPTDX424E is DMxX controlled and features 4 channels with LED indication and a chaser function Make sure that the device was not damaged in transit If the device is damaged you should contact your dealer and postpone installation of this device 2 Safety Instructions oa Be very careful when installing the device touching live wires can cause life threatening electroshocks AN Do not touch the device during operation as the housing heats up Protect this device against rain and moisture Unplug the supply cable before you open the housing e A qualified technician should install and service this device e Damages caused by disregarding certain guidelines in this manual are not covered by the warranty and the dealer will not accept responsibility for the ensuing defects or problems e Do not switch the device on immediately if it has been exposed to changes in temperature Protect the device against damage by leaving it switched off until it has reached room temperature e This device falls under protection class I It is essential therefore that the device be earthed A qualified person must carry out the electric connection e Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual e Do not crimp the power cord and protec
3. d to the DMX input 1 a chase pattern CH1 2 3 4 CH1 2 etc The speed is adjustable with V and A and the speed setting upon activation is always 1 step per 2 seconds 2 channel testing Press 1 2 3 or 4 to test the channels Press 5 to test the strobe Select the desired function with the FUNC button 7 Programming the Starting Address Use the DIP switches to set the start address which is always defined through binary encoding Examples 01010010 0 2 0 8 0 0 64 0 74 10001110 1 0 0 0 16 32 64 113 8 Cleaning and Maintenance 1 All screws should be tightened and free of corrosion 2 The housing mounting supports and connections should not be modified or tampered with e g do not drill extra holes in mounting supports do not change the location of the connections 3 The electric power supply cables should be undamaged Have this device installed by a qualified technician 9 Caution e Disconnect the device from the mains prior to maintenance e Use a moist cloth to clean the device and avoid the use of alcohol or solvents for cleaning purposes e This device does not contain any user serviceable parts Replace a blown fuse with an identical one e Spare parts should be ordered with your local dealer LPTDX424E 3 GB 10 Technical Specifications Power Supply max 230Vac 50Hz Number of channels 4 Max total current 15A DMX input 5 pin XLR male socket DMX output 5 pin XLR female socket Max len
4. gth DMX cable 100m Dimensions 482 x 88 x 80mm Weight 2 2kg The information in this manual is subject to change without prior notice LPTDX424E 4 GB
5. t it against damage from sharp edges Ask an authorised dealer to replace the cord if necessary e Always disconnect the device from the mains when it is not in use or when you wish to clean it Only handle the power cord by the plug Never pull out the plug by tugging the power cord e Do not look directly into the light source as sensitive people may go into epileptic seizure if they do e Be aware that damages caused by user modifications to the device are not covered by the warranty Keep the device away from children and unauthorised users LPTDX424E 1 GB AUN COONDH General Guidelines This device is a light controller for professional use on stages in discos theatres etc This device should only be operated with an alternating current of max 230Vac 50Hz and is designed for indoor use only Do not shake the device Avoid brute force when installing or operating the device Select a location where the device will be protected against extreme heat moisture and dust Do not use or transport the device under temperatures lt 5 C or gt 35 C Familiarise yourself with the functions of the device before actually using it Do not permit operation by unqualified people Any damage that may occur will probably be due to unprofessional use of the device Use the original packaging if the device is to be transported Note that all modifications of the device are forbidden for safety reasons Do not remove the serial number sticker
Download Pdf Manuals
Related Search