User Manual
Contents
1. and Backlight Compensation BLC Internal INT Sync System Fixed lens or Aspherical auto iris vari focal lens with IR correction Power cable and video cable included 12VDC 24VAC power input low power consumption CHAPTER Ill INSTALLATION 3 1 Mounting Process STEP 1 Secure Dome s Adapter in the desired ceiling position with the 3 fixing screws as shown in Figure 1 Figure 1 See the figure below for the adapter mounting holes Unit mm Figure 2 STEP 2 Remove the Dome Cover Align the 3 grooves of the camera unit with the 3 bolts in the adapter and turn counterclockwise to make it fixed Vari focal lens Fixed focal lens Figure 3 STEP 3 The vertical angle can be adjusted by loosening the screws as shown in Figure 4 and by turning the Camera Case vertically Vari focal lens Fixed focal lens Figure 4 STEP 4 The horizontal angle can be adjusted by turning the Camera Case and bracket in Figure 5 and by turning the Camera Platform horizontally Vari focal lens Fixed focal lens Figure 5 STEP 5 After finishing angle adjustment set the camera function by using the buttons in the back panel see Chapter IV STEP 6 Place the Dome bubble over the Camera and tighten it by turning it to the right In this process the shielding cover may block the camera User can adjust the position of shielding cover by turning the bubble With the shielding cover at the proper position the installatio2. F L to F L to activate the F L function strengthening the camera image stability with electronic shutter set to 1 100s NTSC or 1 120s PAL OFF Shut Default as OFF Notice F L function cannot be activated simultaneously with AES If F L function activated AES becomes not available AGC HIGH AGC LOW Selection Magnify the signal collected from CCD to an available standard to video amplifier and how much it magnifies equals to gain which means the sensitivity Adjust AGC properly to have camera work under a larger illumination area AGC Activate AGC HIGH function and it can add 15dB illumination sensitivity under faintly light environment to promote the image signal strength for better impression OFF Activate AGC LOW function and it can add 5dB illumination sensitivity with less video signal noise Default as AGC AES Selection Camera automatically modulate the exposure time if AES function is activated Default as OFF for auto iris lens AES for non auto iris lens Notice When it comes to auto iris lens if trying to modulate brightness via LEVEL AES switch has to be set to OFF BLC Function When the background of view is pretty bright and objects on front cannot be seen clearly it needs to use back light compensation function BLC Activate BLC and then the workstations of AGC AES and IRIS confirm the entire view to distinguish the bright backg
3. Infinova V5411 A2 SERIES INDOOR COLOR DOME CAMERA Infinova CONTENTS Chapter I Description Chapter II Main Features Chapter III Installation 3 1 Mounting Process 3 2 Handling Precautions 3 3 Installation Precautions Chapter IV Camera Function Setting 4 1 Camera Module Back 4 1 1 Operation Instruction 4 1 2 Lens Driving Signal Selection 4 2 Power Board Appendix I Specification Appendix II Cable Diameter Calculation and Lightning amp Surge Protection CHAPTER I DESCRIPTION Thank you very much for purchasing our product This manual addresses the operation and programming procedures of V5411 A2 color dome camera V5411 A2 series indoor color fixed minidome cameras feature a high resolution 1 3 CCD sensor and excellent low light operation They are available in resolutions of 480 TV lines at 0 3 lux They are built in a fixed lens or an auto iris vari focal lens The cameras are designed for surface mount with 2 axis adjustment and require 12VDC 24VAC for power The cameras provide excellent image quality along with ease of installation This manual is for the following models V5411 A2004ST V5411 A2004SU V5411 A2004SW V5411 A2004SX V5411 A2004SB V5411 A2014ST Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL NTSC 12VDC 24VAC Surface mount 2 8mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL NTSC 12VDC 24VAC Surfac
4. e mount 3 6mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL NTSC 12VDC 24VAC Surface mount 6mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL NTSC 12VDC 24VAC Surface mount 8mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL NTSC 12VDC 24VAC Surface mount 2 5 6mm vari focal lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL PAL 12VDC 24VAC V5411 A2014SU V5411 A2014SW V5411 A2014SX V5411 A2014SB Surface mount 2 8mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL PAL 12VDC 24VAC Surface mount 3 6mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL PAL 12VDC 24VAC Surface mount 6mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL PAL 12VDC 24VAC Surface mount 8mm fixed lens Analog minidome camera 2 axis Indoor 1 3 inch CCD Color only 480TVL PAL 12VDC 24VAC Surface mount 2 5 6mm vari focal lens CHAPTER Il MAIN FEATURES 1 3 SONY HAD CCD sensor High Resolution at 480 TVL Low Light operation at 0 3 Lux Digital Signal Processor DSP for high quality image High sensitivity low smear high anti blooming and high S N ratio Auto Electronic Shutter AES Auto Gain Control AGC Auto Tracking White Balance ATW Flickerless FL
5. g device Additional high power lightning proof equipment and lightning rods should be installed for strong thunderstorm or high induced voltage areas such as high voltage substation The lightning protection and grounding for outdoor devices and wires should be designed in line with the actual protection requirement national standards and industrial standards The system should perform equipotential grounding by streaming shielding clamping and earthing The grounding device must meet anti interference and electric safety requirements There should be no short circuiting or hybrid junction between the device and the strong grid Make sure there s a reliable grounding system with grounding resistance below 4Q below 10Q for high soil resistivity regions The cross sectional area of the earthing conductor should be no less than 25mm Lightning rod Front device for surveillance system Mounting pole for front device Separated layout for the lightning rod and the standing pole Infinova 51 Stouts Lane Monmouth Junction NJ 08852 U S A Tel 1 888 685 2002 USA only 1 732 355 9100 Fax 1 732 355 9101 sales infinova com V2 3 1401
6. n is finished Dimensions Unit mm 128 0 Figure 6 3 2 Handling Precautions Never let liquid of any kind flow into this unit Do not directly touch the CCD element If it is necessary to clean the dome bubble use a soft cloth moistened with alcohol to wipe off any dust If any abnormality occurs make sure to unplug the unit and contact your local dealer This camera possesses AGC circuit Therefore when the camera is used under lower luminance the sensibility will strengthen automatically and make the image very rough in vision It is normal When the camera is used in ATW mode due to the working principle of auto trace white balance the recorded color is slightly different from the real color It is normal If the subject is with high luminance like lamp vertical stripes will occur on the monitor tailing shadow or the surrounding image becomes vague flowering It is special phenomenon of CCD not error The power supply for this camera is 12VDC or 24VAC 24VAC must be isolated power 3 3 Installation Precautions 1 2 Do not drop the camera or subject it to strong knock Do not point the camera lens toward the sun or other strong light Do not install the camera in environment with temperature beyond the acceptable range from 10 C to 50 C or with high humidity direct rainfall frequent vibrations and shocks Under the default setting the lens has been adj
7. nnect the power video interface 5 on the rear panel of the camera module J4 J4 is used for debugging APPENDIX I SPECIFICATION Model Type V5411 A2 Series Image Sensor 1 3 SONY HAD CCD Effective Pixels HxV NTSC 768 x 494 380k PAL 752 x 582 440k Resolution 480 TVL Minimum Illumination 0 3 lux F1 2 30IRE AGC ON Scanning Frequency 15 625kHz lines 50Hz fields S N Ratio gt 48dB AGC OFF Auto Electronic Shutter 1 60 1 100 000 s 1 50 1 100 000 s Fixed F2 0 f 2 8mm 3 6 mm 6mm or 8mm Vari Focal F1 2 f 2 5 6 mm Camera Angle Adjustment X Panning 0 360 Y Tilting 0 85 Flickerless Mode ON OFF Auto Gain Control ON OFF Auto White Balance ATW Color Temperature Range 2400K 8000K Backlight Compensation ON OFF Gamma Correction 0 45 Lens Sync System Internal Video Output 1 0 Vp p 75 Ohm BNC connector Power Supply 12VDC 24VAC Power Consumption 12 VDC 3 W 24 VAC 4W Operating Temperature 14 F 122 F 10 C 50 C Operating Humidity 0 90 RH non condensing Unit Dimensions Hx 97 5mmx128mm Box Dimensions LxWxH Unit Weight 0 27kg Shipping Weight 0 47kg 140mm 140mm 120mm Specifications and appearance are subject to change without notice APPENDIX Il CABLE DIAMETER CALCULATION AND LIGHTNING amp SURGE PROTECTION Relation between 24VAC Cable Diameter and Transmission Distance In general the maximum allowable voltage loss rate is 10 for AC powered de
8. round area and the dark front objects OFF Shut When the contrast between view background and front objects is not big it will not need to activate back light compensation function Default as OFF Notice It has to activate AGC in the first place to make BLC function take effect 4 1 2 Lens Driving Signal Selection 1 This item is used to select the mode of the auto iris to provide the driving signal to the auto iris driving interface on the lens If the lens applies DC drive please set the lens driving signal selection switch to DC If the lens applies VIDEO drive please set the lens driving signal selection switch to VIDEO 4 2 Power Board The main function of the power board is to convert the 12VDC 24VAC output voltage to 12VDC and supply to the camera NIANG Figure 10 J1 12VDC 24VAC input and video output interface Draw out the cables on JI through the base or side of camera cover Normally cables should be drawn out from base and connect them to power supply and monitor respectively shown as the figures below To 12VDC Power TA NN To 24VAC Power To Monitor Ais SS To Monitor To 12VDC Power NN ZI To 24VAC Power To Monitor ey T ji To Monitor Figure 12 Cable from side J2 power output and video input interface J2 co
9. rrier effectively avoids product damage caused by various pulse signals with power below 4kV including instantaneous lightning surge and static However for complicated outdoor environment refer to instruction below for lightning and surge protection The product features with dedicated earth wire which must be firmly grounded As for surveillance sites beyond the effective protection scope it s necessary to erect independent lightening rods to protect the security devices It s recommended to separate the lightning rod from the mounting pole placing the rod on an independent pole as shown in the figure below If the product has to be installed on the same pole or pedestal for lightning rod there should be strict insulation between the video cable BNC terminal power cable control cable and the standing pole of the lightning rod For suburb and rural areas it s recommended to adopt direct burial for the transmission cables Overhead wiring is prohibited because it s more likely to encounter lightning strike Use shielded cables or thread the cables through metal tubes for burial thus to ensure the electric connection to the metal tube In case it s difficult to thread the cable through the tube all the way it s acceptable to use tube threaded cables only at both ends of the transmission line yet the length in burial should be no less than 15 meters The cable sheath and the tube should be connected to the lightning proof groundin
10. usted till the object in a 1 5m distance becomes clear The lens can be readjusted as per the actual surveillance scenes Lens Adjusting 1 Fixed focal lens a Loosen the locking screw as shown in Figure 7 with an Allen wrench b Slowly rotate the lens until the sharpest image is seen on the monitor c Tighten the locking screw oh Locking screw Allen wrench Figure 7 2 Vari focal lens a Loosen the zoom tightening knob and the focus tightening knob b Slowly rotate the zoom ring to adjust the focal length c After a zoom operation slowly rotate the focus ring to obtain the sharpest image on the monitor d If there are still blurred images loosen the locking screw with an Allen wrench as shown in Figure 8 to adjust the back focal length and repeat the above procedures e Tighten the zoom tightening knob the focus tightening knob and the locking screw Focus tightening knob Zoom tightening knob Locking screw Figure 8 CHAPTER IV CAMERA FUNCTION SETTING 4 1 Camera Module Back YAN 1 T Y Figure 9 D Function Setup Switch Auto IRIS lens select 3 Auto IRIS lens Jack 4 RS 232C Jack Power Input and Video Out Jack 8 LEVEL Video adjust 4 1 1 Operation Instruction FL Function F L If fierce image flicker caused by the conflicting frequency between camera and environment such as NTSC camera works under 50Hz power environment switch OFF
11. vices The table below shows the relationship between transmission power and maximum transmission distance under a certain specified cable diameter on condition that the 24VAC voltage loss rate is below 1096 According to the table if a device rated at 50W is installed 17 meter away from the transformer the minimum cable diameter shall be 0 8000mm A lower diameter value tends to cause voltage loss and even system instability Diameter mm 0 8000 1 000 1 250 2 000 283 86 451 137 716 218 1811 551 141 42 225 68 358 109 905 275 94 28 150 45 238 72 603 183 70 21 112 34 179 54 452 137 56 17 90 27 143 43 362 110 47 14 75 22 119 36 301 91 40 12 64 19 102 31 258 78 35 10 56 17 89 27 226 68 31 9 50 15 79 24 201 61 28 8 45 13 71 21 81 55 25 7 41 12 65 19 64 49 23 7 37 11 59 17 50 45 21 6 34 10 55 16 39 42 20 6 32 9 51 15 29 39 18 5 30 9 47 14 20 36 17 5 28 8 44 13 13 34 16 4 26 7 42 12 06 32 15 4 25 7 39 11 00 30 14 4 23 7 371 95 28 14 4 22 6 35 10 90 27 Lightning amp Surge Protection The product adopts multi level anti lightning and anti surge technology integrated with gas discharge tube power resistor and TVS tube The powerful lightning and surge protection ba
Download Pdf Manuals
Related Search