TS-590S KENWOOD NETWORK COMMAND SYSTEM Setting Manual
Contents
1. 13 4 4 Setting Transmission Methods for Audio Input to the Rear Terminal 16 4 5 Setting Broadband Routers 17 4 6 Software Installation and Settings 18 4 7 Windows Firewall Settings 19 4 8 Comprehensive Security Software Settings 19 4 9 Setting the Host Station Wait Mode 19 4 10 Connecting to the Host Station from the Remote Station 19 5 Limitations Caution 20 5 1 PC Environment Limitations 20 5 2 Network Environment Limitations 20 5 3 Program Limitations 21 5 4 Limitations if Using USB Audio Functions 21 6 Frequently Asked Questions2. 22 Windows is a registered trademark or trademark of Microsoft Corporation in the United States and other countries NET Framework is a registered trademark or trademark of Microsoft Corporation in the United States and other countries Bluetooth is a registered trademark or trademark of Bluetooth SIG Inc The names of all products described hereafter are the trademarks or registered trademarks of their respective manufacturers and are omitted throughout the text Disclaimer All efforts have been made regarding the accuracy of the contents described in this document However there is a possibility of misprints and of descriptions that may cause misunderstanding Kenwood Corporation bears absolutely no responsibility for damages arising thereof Kenwood Corporation may revise and amend the product information described in this document without notice Kenwood Corporation bears absolutely no responsibility for damages arising thereof 3 1 Relevant Models This user guide is for the TS 590S Using the TS 590S and KENWOOD NETWORK COMMAND SYSTEM hereinafter called KNS enables transceiver operations by remote control using a domestic LAN or the internet See Note KNS is a system configured using PCs network environments ARCP 590 a Radio Control Program hereinafter called ARCP 590 and ARHP 590 a Radio Host Program hereinafter called ARHP 590 for remote control of the TS 590S Not
3. Station Transmitter Operations The host station is configured using a transceiver and a PC connected to the network Data signals that control the transceiver are connected to the PC using either RS 232C or USB The computer uses its sound function to input and output audio transmitted and received by the transceiver and converts them between digital and analog signals The ARHP 590 is installed on the computer and exchanges transceiver control data signals with the network The PCs are connected to the network and trade transceiver control data signals and transmit and receive audio with the Remote station operator on the network Note To transmit and receive audio separate VoIP software is required 6 3 3 Host Station Transmitter Configuration Transceiver TS 590S The TS 590S transceiver is supported The ARCP 590 and ARHP 590 are specialized for the TS 590S and so other transceivers cannot be used to configure the system USB or RS 232C Controls that change the frequency or mode are performed by connecting the transceiver and PC using either a USB cable or RS 232C cable The transceiver has only one RS 232C terminal so if using the RS 232C terminal for KNS operations another device cannot be connected Connection Audio Created by the customer To transmit and receive audio connect the wireless ACC2 terminal to the PC sound I O terminal For the transceiver terminal specifications refer to the device user manua
4. be careful during PC operations and when playing these files Depending on the combination of PC and sound functions normal operations may be disabled Kenwood does not offer support for customer computers We recommend using audio cables without using USB audio functions for KNS operations See 4 2 Connecting Audio Cables 22 6 Frequently Asked Questions This section introduces questions that have been asked to date and subjects verified by Kenwood Corporation Question Answer With internet routing is KNS disabled unless I obtain a global IP address With internet routing a global IP address is required I have a variable global IP address Can I still use it Variable IP addresses can also be used but each time the IP address changes it is necessary to reset the settings which is inconvenient We recommend using a fixed IP address Even with a variable IP address the inconvenience of resetting the settings can be eliminated by using a dynamic DNS service which can be used in the same way as a fixed IP address I use CATV internet Can I use KNS via the internet If you can obtain a global IP address yes If using a type with the broadband router built into the cable model it is possible if port forwarding settings can be made Can I use environments with both host stations or remote stations or with a proxy and firewall Proxy and firewall environments cannot be used Both host stations remote stat
5. the existing device using the PC sound functions Use the PC sound functions to check whether the PC speakers have been selected as the playback device When playing audio and video when implementing KNS operations on the PC used as the host device the audio is transmitted from the TS 590S During KNS operations all audio output from the PC is input to the TS 590S as transmitted audio During KNS operations do not play audio or video Furthermore we recommend waiting until other programs have ended Loud sounds are suddenly output from the host station transceiver The cause is the remote station user operating the volume control You can use the ARHP 590 to prohibit volume operations from the remote station Select the Tools menu and the Settings and enable the Prohibit AF gain control from ARCP 590 checkbox Other After restarting the host station for any reason are there any settings to enable standby mode automatically In the ARHP 590 Tools menu select Settings and then enable the Implement automatically during Windows startup checkbox When the PC is restarted it will automatically enter standby mode 28 Supplement FAQ Explaining the Internet Cannot operate transceiver Fig 1 As shown in Fig 1 even though only one broadband router BBR is visible on the network in reality there are two Duplex router phenomenon There are multiple modem modes with built in BBR functions so
6. the host station global IP address is fixed is recommended Furthermore if the global IP address cannot be fixed using a dynamic DNS service enables operations in the same way as an environment with a fixed global IP address 8 3 4 Overview of Remote Station Operator Operations The remote station is configured using a PC connected to the network and a microphone and speaker connected to the PC sound function The audio transmissions for the host station transceiver are input and output using the microphone and speaker connected to the sound function of the remote station PC via the network The ARCP 590 is installed in the PC The host station transceiver connected via the network is controlled by remote station ARCP 590 operations See Note Note To transmit and receive audio separate VoIP software is required 9 3 5 Remote Station Operator Configuration PC ARCP 590 VoIP LAN WAN Connection Audio To exchange audio transmissions connect the microphone and speaker or a headset to the PC sound function Use products compatible with the sound function used Specifications CPU and memory Minimum values recommended by the operating system HDD To install the ARCP 590 a minimum of approx 100 MB of free disk space is required If saving transceiver settings to data files or saving keystroke logs additional memory space is required Sound funct
7. 590 help file To transmit and receive audio download and install separate VoIP software Caution Support for selecting installing and operating VoIP software is not available from Kenwood Corporation 19 4 7 Windows Firewall Settings With the host station PC receiving connections from networks and the internet using the ARHP 590 are blocked by the Windows firewall When blocked KNS operations are disabled so remove the block Reference Add the ARHP 590 to exceptions using the Windows firewall settings to release the block 4 8 Comprehensive Security Software Settings If using comprehensive security software it is necessary to adjust the settings so that ARHP 590 and ARCP 590 communications are not blocked Perform the settings with reference to the user manual for the comprehensive security software used 4 9 Setting the Host Station Wait Mode Click the Connections button in the main window of the ARHP 590 on the host station The indicator will light yellow and the remote station will enter connection request wait mode If the audio transmission is speech set the VoIP software to standby mode 4 10 Connecting to the Host Station from the Remote Station Click the Connections button in the main window of the ARCP 590 on the remote station If the connection to the host station is successful the indicator will light green If the audio transmission is speech connect the host station with the VoIP software too 20 5 Limi
8. ACC2 connector Input is also possible using USB audio functions from a USB connector but as the delays are great this is not recommended Make the following menu settings to transmit audio input from the ACC2 connector Menu No Function Set value 63 Audio input line selection for data communications ACC2 The default setting is ACC2 Reference Set the menu described above to USB to transmit USB audio signals input to the USB connector Set the existing device connected to the TS 590S to the playback and recording devices using the PC sound settings on the host station Data VOX settings With the TS 590S VOX functions can be implemented using either audio input to the ACC2 connector or USB audio signals input to the USB connector but to prevent unintentional transmission during KNS operations turn OFF the function using the menu settings Menu No Function Set value 69 Data VOX OFF The default setting is OFF Caution There is a risk that sounds other than those produced by the computer may be transmitted unintentionally over the network so we recommend that you turn off this function When this function is ON all sounds created by the computer other than the intended audio transmissions are also transmitted so be careful When using this function for the first time we recommend connecting a dummy load to the TS 590S to perform checks and adjustments 14 Audio I O level settings Use the following menu
9. Set value 49 Time out timer except OFF See Note The default setting is OFF 15 Note Select from 3 5 10 20 30 minutes excepting OFF depending on the situation to use Prohibit transmission setting If using the host station as a receive only station set to transmission inhibited Make the settings using the following menu Menu No Function Set value 60 TX inhibit ON The default setting is OFF Allocating DATA SEND functions to PF keys Set the DATA SEND functions to the PF keys to test the transmission of audio input from the rear terminal In this example the PF A key has been set Menu No Function Set value 79 Front panel PF A key assignment 205 The default value is 200 VOICE1 Using the PF keys which set the DATA SEND functions enables switching between transmit and receive modes for audio input from the rear terminal 16 4 4 Setting Transmission Methods for Audio Input to the Rear Terminal The SEND keys on the PTT of the microphone connected to the TS 590S and on the TS 590S control panel are the method for transmitting audio input to the microphone connected to the TS 590S so even if these operations are implemented audio entered as audio signals from ACC2 cannot be transmitted To transmit audio input as audio signals from the ACC2 select one of the following methods Transmitting using the ARCP 590 With the ARCP 590 settings must be done to transmit audio input throug
10. TS 590S KENWOOD NETWORK COMMAND SYSTEM Setting Manual October 15 2010 2 CONTENTS 1 Relevant Models 3 2 Objectives of this document 3 3 Outline 4 3 1 Overall Configuration 4 3 2 Outline of Host Station Transmitter Operations 5 3 3 Host Station Transmitter Configuration 6 3 4 Overview of Remote Station Operator Operations 8 3 5 Remote Station Operator Configuration 9 4 Settings 11 4 1 Connecting Communications Cables 11 4 2 Connecting Audio Cables 11 4 3 Transceiver Settings
11. ceiving operations immediately after the conversation has finished using the remote station you may switch to receiving before all the audio has been transmitted due to the audio transmission delay In such cases use the ARCP 590 pulldown menu to select Tools and then Transmit control settings and set a slightly longer time in Switching delay from transmit to receive during network connections Operations When implementing synchronous steps other than Preset reaction may be delayed during KNS operations When set to other than Preset the network is more easily delayed than when using Preset due to the difference in the internal commands In such cases either select Preset and perform synchronization or change the frequency using the MULTI CH operation 27 Question Answer Comprehensive security software etc I m using comprehensive security software but when I try a KNS connection the warning Software is attempting to connect to the internet is displayed Can I press the Block button Refer to the user manual for the comprehensive security software being used and set it so that the communications of the port used by ARCP 590 and ARHP 590 are not blocked After implementing KNS operations on the PC used as the host station the sound has vanished from the PC during audio and video playback on the PC It is possible that the device connected to the TS 590S has been selected as
12. e To transmit and receive audio separate VoIP software is required Important To configure the system knowledge not only of transceivers but also of PCs and networks is required Kenwood does not offer support for customer computers and Networks Furthermore for operations relating to actual transmitting note that procedures according to the Radio Act are also required Operations via networks may be delayed due to unavoidable principles Consequently do not perform operations such as contests or pile ups requiring quick responses for which delays are likely to be a problem Refer to Chapter 5 for other limitations Kenwood Corporation shall bear no responsibility for related damage such as damage caused by missed communications and dialog opportunities due to incorrect customer settings nonconformances or misoperations as a result of using this document or the ARCP 590 or ARHP 590 software 2 Objectives of this document To supply information to configure a remote control system via an internal LAN or internet using the TS 590S ARCP 590 and ARHP 590 The following describes the main elements Via Internet Internal LAN Programs Used ARCP 590 Operates transceiver remotely ARHP 590 Operates via the ARCP 590 and transceiver VoIP software transmits and receives audio ARCP 590 Operates transceiver remotely ARHP 590 Performs operations via the ARCP 590 and transceiver VoIP software transmits and receives audio N
13. e internet operations can be misunderstood 25 Question Answer If using the sound functions in comprehensive chipsets try an independent sound card or USB sound Adjust the ACC2 audio level in menus 66 and 67 There is static in the audio transmissions or audio transmissions are faint Where should I check and adjust them Try changing the sound function driver version I can hear the beeping and voice guidance audio from the transceiver on the nearby PC Alternatively I want to be able to hear them but can t Set using the Mix beeps with external audio device in menu 68 Can I set the PC to sleep mode while I m not using the host station When a fixed time has elapsed without the host station being used the station PC screen turns OFF and responses to connection requests from the station cannot be made Recovery from sleep mode takes time During sleep mode recovery responses to the remote station cannot be returned until there is a time out Therefore we recommend you do not set the station to sleep mode If there is a connection request from the remote station while the host station is not being used a message is displayed and connections to the host station are disabled Is the OS energy save mode operating and has the power supply to the host station HDD been disabled When the HDD power supply is turned OFF the HDD power supply is turned ON to respond but at this time nothing can be re
14. ettings are possible using the following protocol is required to transmit the data signals that control the transceiver See Note 2 Protocol TCP port No 50000 KNS default value Modem Not specified LAN environment Other To implement KNS operations via the internet firewall environments configured using in house company networks cannot be used Use a domestic network environment Provider To implement KNS operations via the internet A high speed cable broadband environment using xDSL FTTH or CATV network is required 1Mbps min recommended A global IP address is required See Note 3 The ability to use protocols and ports to transmit the data signals that control the transceiver is required Protocol TCP Port No 50000 KNS default value For details contact your internet service provider Internet environment Proxy Proxy servers cannot be used Note 1 Support for selecting installing and operating VoIP software is not available from Kenwood Corporation Note 2 Make sure to refer to the user manual for the broadband router to be used before performing the settings Note 3 KNS operations are possible even if the global IP address is variable but the IP address may change with uncertain timing In such cases it is necessary to check and change the IP address of the connected host when connected from a remote station which reduces user friendliness Consequently using an environment in which
15. etwork Connections via the internet To use the internet a contract with a provider is necessary Connection using internal LAN IP address used Global IP address Local IP address Application based on the Radio Act Application using the internet Application using internal LAN 4 3 Outline 3 1 Overall Configuration Fig 3 1 1 Example of internal LAN configuration In this diagram the modem router and hub have been omitted As shown in the diagram the configuration uses a host station where the transceiver is installed this is called the transmitter in the Radio Act and a remote station which performs the remote operations this is called the operator in the Radio Act A PC is connected to both and the PCs are connected to each other via the network The transceiver connected to the PC to which the ARHP 590 has been installed on the host station is operated using the ARCP 590 which has been installed on the remote station PC Furthermore transmitted and received audio for the transceiver on the host station can be transmitted using the mike and speaker connected to the PC sound device on the remote station See Note Note To transmit and receive audio separate VoIP software is required Remote station Host station TS 590S 5 Fig 3 1 2 Example of KNS configuration via the internet The host station and remote station can be installed in any location with an internet connection 3 2 Outline of Host
16. h the rear terminal to use the on screen SEND key Select Set transmit control from the ARCP 590 Tools menu The Transmit control settings window is displayed In this window select ACC2 USB in the modulation line and then select ACC2 For details refer to the ARCP 590 help Transmitting using the PKS terminal in the ACC2 connector Audio input to the rear terminal can be transmitted by setting the PKS terminal in the ACC2 connector on the rear of the TS 590S to low For details of the connector and terminal specifications refer to the TS 590S user manual Transmitting using the PF keys allocated to the DATA SEND functions If the DATA SEND functions have been allocated to the PF keys operating the PF keys enables audio input to the rear terminal to be transmitted For details refer to Allocating DATA SEND Functions to PF Keys 17 4 5 Setting Broadband Routers If implementing KNS operations via the internet it is necessary to set the broadband router connected to the host station Make the settings to transmit control data signals transmitted via the internet from the broadband router to the host station PC This setting depends on the call method of the broadband router manufacturer and may be Port forwarding IP masquerade Port conversion NAT address conversion etc Refer to the user manual for the broadband router used The settings are described below Item Example Setting Details Open IP add
17. ion To exchange audio transmissions a sound function is required PC Network function A cable network is recommended Connect to a hub or router OS Use Windows XP SP3 or later Windows Vista SP1 or later 32 bit version only or Windows 7 32 bit or 64 bit version Other operating systems are not compatible Run time To use KNS operations on Windows XP Microsoft NET Framework 2 0 or later is required If it is not installed install it when installing ARCP 590 ARCP 590 This software remote controls the transceivers Refer to the software help for the settings and operation methods Download the software from the download page and install on the PC http www kenwood com i products info amateur software_download html Software VoIP software To transmit and receive audio VoIP telephone software is required See Note 1 Transmit audio Receive audio Sound function VoIP software 10 Router Same as host station Modem Same as host station LAN environment Firewall Same as host station Provider Same as host station Internet environment Proxy Same as host station Note 1 Support for selecting installing and operating VoIP software is not available from Kenwood Corporation 11 4 Settings 4 1 Connecting Communications Cables Connect the host station PC and TS 590S using an RS 232C or USB cable Note RS 232C cables and USB cables are sold separately Purchase them from a comme
18. ions can be used only on general home network environments Installation Can I use a wireless LAN or BWA broadband wireless access We do not recommend this as line speeds are not fixed for best effort type wireless 23 Question Answer Installation I want to use headsets USB headsets and Bluetooth headsets on the remote station PC Will there be any problems You can use them but in principle USB headsets and Bluetooth headsets have unavoidable delays so entering standby will take considerable time If the delays are a problem it is better to avoid using them After connecting USB headsets or Bluetooth headsets it is necessary to set the existing recording and playback devices using the OS sound properties For details refer to the USB headset or Bluetooth headset user manual Internet Cannot use transceiver operations Cannot connect to the host station Check that connections to websites and the internet mail server are possible Check the host station address ID and password If there are no problems check the following Check that the port used for wireless control TCP default setting 50000 is set to open on the host station broadband router Check that there are not two or more broadband routers hereafter called BBR on the host station network If there are two or more BBRs either open the port required by KNS for either of the BBRs or stop one of the BBRs and make sure that
19. l and for the cable creation and connection methods refer to 4 2 Connecting Audio Cables Specifications CPU and memory Minimum values recommended by the operating system HDD To install the ARHP 590 a minimum of approx 100 MB of free disk space is required If storing connection logs additional memory space is required Sound function To transmit and receive audio a sound function is required PC Network function Connects to the internal LAN To perform KNS operations via the internet connect to a network that is connected to the internet A cable network is recommended Software OS Use Windows XP SP3 or later Windows Vista SP1 or later 32 bit version only or Windows 7 32 bit or 64 bit version Other operating systems are not compatible Transceiver control Transceiver Sound function Audio transmission VoIP software 7 Run time To use KNS on Windows XP Microsoft NET Framework 2 0 or later is required If it is not installed install it when installing ARHP 590 ARHP 590 This software controls the transceivers Refer to the software help for the settings and operation methods Download the software from the download page and install on the PC http www kenwood com i products info amateur software_download html VoIP software To transmit and receive audio VoIP software is required See Note 1 Router To implement KNS operations via the internet a model on which port forwarding s
20. ntests or quick operations such as pile ups VFO variability may not be smooth audio may differ from the actual transceiver audio and digital mode communications such as image communications with SSTV and AFSK PSK 31 etc may be disabled etc Broadband is recommended for the internet line used As a benchmark use a minimum of 1 Mbps The speed of analog modems that use telephone lines will greatly reduce sound quality and may destabilize control and so cannot be used 21 5 3 Program Limitations CW operations are possible but keying using normal e keys is not possible Strings entered using the keyboard are collated for transmit operations 5 4 Limitations if Using USB Audio Functions If the PC and TS 590S are connected via a USB cable audio transmissions can be transmitted using the USB audio function In principle however there is a delay with USB audio so sound may be lost depending on the PC performance and load status If using a USB connection for transmitting audio on the host station the delay due to network traffic to the remote station is also added so the delay is further increased If audio transmissions are connected via USB terminals and if playing warning sounds from the OS or music and video on the PC the sounds may not emit from the speakers Furthermore depending on the OS sound and properties the transceiver DATA VOX function settings and the modulation path the audio may be modulated from the transceiver so
21. only one BBR exists on the network and then set the required KNS port to open on the BBR See Page 28 OS When attempting a KNS connection a warning message may be displayed depending on the OS Add ARHP 590 to the Windows firewall exceptions 24 Question Answer Why can t I use the ARCP 480 The ARCP 480 is for the TS 480 only Use the ARCP 590 with the TS 590S Why can t I use the ARHP 10 The ARHP 10 is for the TS 480 only Use the ARHP 590 with the TS 590S Reception quality depends on the device Audio via a network is affected by the audio encoding and data bandwidth and so sound quality may differ from the actual received quality These are VoIP specifications and cannot be improved I want to control peripheral devices other than the antenna and transceivers The current system is compatible only with transceiver control Operations There are so many limitations can this system operate Although different from normal operations considerably practical operations are possible in ordinary communications There may be some initial confusion over the standby timing until you are familiar with the specific delays via the network We recommend first becoming familiar with the transceiver operations from the PC using a single ARCP 590 and then attempting operations on a network environment as the next step When attempting actual operations unless there are no communications to a partner remot
22. rcial outlet If connecting using an RS 232 cable ensure that it is a straight cable 9 pin to 9 pin If connecting using a USB cable 1 Download the installer for the virtual COM port driver from the Kenwood homepage http www kenwood com i products info amateur software_download html then install it according to the procedures 2 Connect the PC and TS 590S using the USB cable 4 2 Connecting Audio Cables To transmit and receive audio an audio cable is required Create an audio cable using the 13 pin DIN plug enclosed with the TS 590S with reference to the following diagram For details of the terminal specifications refer to the TS 590S user manual Fig 4 2 1 Creating an audio cable 12 Connect sound functions and audio cables with reference to the following diagram Fig 4 2 2 Connecting audio cables Reference If the TS 590S is connected to the PC using a USB cable audio transmission input and output are possible using the USB audio function but the many signal conversions cause inherently unavoidable delays Furthermore during KNS operations network delays will occur To minimize delays as much as possible connections using audio cables are recommended Delays also depend on the PC load and network traffic 13 4 3 Transceiver Settings Make the settings required to implement KNS operations using transceivers Set the audio path settings With KNS operations normally transmitted audio is input from an
23. ress IP address of the PC used in the host station Protocol TCP Port Number 50000 default value Direction Two way Caution For the broadband router settings refer to the broadband router user manual Incorrect broadband router settings may stop the network or enable illegal external access to the network Take thorough precautions when changing the settings Kenwood does not offer support for customer computers and networks 18 4 6 Software Installation and Settings Install the software required for KNS operations on the host station PC and the remote station PC then perform the required settings Host station PC Download and install the ARHP 590 onto the PC from the Kenwood website http www kenwood com i products info amateur software_download html Make the COM settings network settings optional settings and user settings used to connect to the TS 590S by selecting the Tools menu and then Settings in the ARHP 590 For the settings methods refer to the ARHP 590 help file To transmit and receive audio download and install separate VoIP software Remote station PC Download and install the ARCP 590 onto the PC from the Kenwood website http www kenwood com i products info amateur software_download html In the ARCP 590 select the Tools menu and then Settings and set the connection to Network Click the Settings button to make the KNS connection settings For the settings methods refer to the ARCP
24. tations Caution 5 1 PC Environment Limitations Check that the ARCP 590 and ARHP 590 operations use Windows XP SP3 or later Windows Vista SP1 or later or Windows 7 Earlier versions and other operating systems cannot be used Use the operating systems described above for both the host and remote stations For KNS operations it is necessary to set and change the open broadband router port OS firewall functions and comprehensive security software Furthermore it is the customer s responsibility to handle security when using this system If you do not have confidence in the settings we recommended you stop using the system 5 2 Network Environment Limitations During KNS operations via the internet it is necessary to set the global IP address on the host station For your global IP address consult your contracted provider Only registered people can access the host station using their ID and password Make sure that the ID and password settings cannot be guessed easily by unauthorized people On this system signals are exchanged via the network Consequently smooth operations may be disabled compared to normal transceiver operations as delays during analog digital conversions and data loss which is greatly dependant on traffic are unavoidable This is the principle operation of the system Examples are cited below Audio may be cut off meter deflection may not be smooth standby time may be delayed in particular it is not suitable for co
25. to adjust audio transmission input levels from the PC and receive audio output levels to the PC Menu No Function Setting range 64 Audio level of USB input for data communications 0 9 65 Audio level of USB output for data communications 0 9 66 Audio level of ACC2 input for data communications 0 9 67 Audio level of ACC2 output for data communications 0 9 The default value for all settings is 4 Reference Adjust the PC sound function volume as necessary Mixed beep setting to external audio outputs With the TS 590S default mode only received audio signals that do not include beeps or side tones are output as audio signals from the ACC2 connector and the USB connector as USB audio signals Make the following menu settings to output the same audio as the audio output from the wireless speaker including beeps and side tones externally Menu No Function Set value 68 Mixing beep tones for ACC2 USB audio output ON The default setting is OFF Reference To implement data communications turn this function OFF Timeout timer settings During KNS operations control data signals are transmitted using the network Consequently if normal network operations are disabled for any reason control of the transceiver will also be disabled Use the following menu to set the functions to stop transmitting automatically after a fixed period if control should be disabled while transmitting Menu No Function
26. turned until the response to the remote station has timed out Consequently set the OS power supply function settings so that the HDD power supply does not turn OFF Audio I O between the host station PC and transceiver cannot be performed correctly Check that an existing device is specified as the device connected to the TS 590S using the host station PC sound settings Operations Modulation is not performed even when the ARCP 590 SEND button is pressed Check that the same path as the modulation path wired between the transceiver and the PC has been selected using the ARCP 590 Transmit control settings 26 Question Answer Refer to the VoIP software user manual and check the settings Check that an existing device has been specified for the PC speakers microphone and headset currently in use using the remote station PC OS sound settings Check whether the PC microphone and headset have been muted or are at low volume Cannot transmit audio correctly between the remote station and host station Check that the PC speakers microphone and headset are connected correctly The audio transmissions keep varying in volume and are not constant Has AGC been turned ON using the VoIP software input audio settings For details refer to the VoIP software user manual and check the settings The final part of the audio transmitted from the host station transceiver is missing If you return to re
27. when connecting such a modem as described above there must not be two BBR paths connecting the PC to the internet Consequently even if the open port has been set for one BBR only the required KNS packets will not flow For this reason either set the required KNS port to open for two BBRs or stop one BBR function and set the network so that there is only one BBR on the network Fig 2 As shown in Fig 2 in cases where the telephone is connected directly under the model nearly all modem models have a built in BBR In such cases stopping the BBR built into the modem stops the VoIP telephone functions connected to the modem so VoIP telephony use is disabled To prevent the VoIP telephone functions from stopping stop the functions of the BBR connected to the front of the PC and set the port required by KNS to open in the BBR built into the modem Caution Change any settings such as open BBR ports at your own risk If you do not have confidence in the settings we recommend you stop using the system Modem BBR Internet Modem BBR Internet
Download Pdf Manuals
Related Search