Home

Redwood RV Owner`s Guide

1. Care and Maintenance Maintaining the Plug requires little effort Store safely when not in use and clean the prongs as needed Please see your dealer if repair work is necessary JS Typically the wires within the 7 Way Plug are color coded as identified in the graphics on this page Brakes Electric Included in the unit packet is an extensive manual by the manufacturer of the brakes axles hubs and drums Please refer to this manual for information of any of these systems Breakaway Switch The breakaway switch is designed to work in the event separation occurs between the tow vehicle and the RV while on the road As separation occurs the pin is pulled from the switch A circuit from the trailer battery to the RV brakes becomes closed and activation of the trailer brakes results Care and Maintenance Do not let the lanyard which is connected to the pin drag upon the ground Inspect the condition of the lanyard prior to travel As well since the breakaway safety feature operates on the trailer battery insure the battery is fully charged and the terminals are clean Testing the switch prior to traveling is recommended See below If a problem is noted or if the switch fails during testing please call your dealer How to Test the Breakaway Switch 1 Disconnect the power cord from the RV to the tow vehicle 2 Pull the lanyard pin ou
2. Capability vs Environment The capability of the air conditioner to maintain the desired inside temperature is directly effected by the heat gain of the RV During extreme high outdoor temperatures the heat gain of the vehicle may be reduced by 1 Parking in a shaded area 2 Keeping blinds down or drapes shut 3 Keeping windows and doors shut and minimize usage 4 Operation on High Fan Cooling mode will provide the maximum efficiency in high humidity or high temperatures Using awnings to block direct sunlight exposure on the unit Avoiding use of heat producing appliances Giving the A C a head start by turning the air conditioner on early in the morning pee D Care and Maintenance Periodically remove the return air filter and wash with hot soapy water During extended use situations cleaning is recommended after two weeks of daily usage Antenna TV The television antenna installed is designed for either color or black and white television If reception is poor make sure the power supply switch is on and connections are tight Should the reception remain poor check with your authorized dealer To Raise Antenna 1 Check location to ensure no obstacles will be encountered while raising the antenna 2 Turn elevating crank clockwise in an UP direction about 13 turns or until resistance is felt 3 Turn Power Supply switch to ON If cable is being used the power supply switch needs to be set
3. Chapter 8 Care amp Maintenance 5 Hole Star Pattern 8 Hole Star Pattern 51 Chapter 8 Care amp Maintenance Some wheel assemblies require an extension DO NOT USE a flexible extension Also DO NOT USE a 4 way socket or any other type of wrench Figure E which does not measure the actual pressure applied to the lug nut If uncertain or unfamiliar with any procedure please call your local dealer WHEEL SEPARATION CAN OCCUR On the first trip check for the proper torque every 10 25 and 50 miles traveled in your coach This procedure should also be repeated every time a wheel is replaced Always torque wheel nuts to the wheel manufacturer s specifications Over or under torqued wheel nuts can cause the wheel to separate from the wheel mounting surface during operation causing property damage personal injury or loss of life 52 3 Complete the procedure on each wheel Before moving to each new wheel be sure to verify your preset torque wrench value After removing a wheel from your RV for any reason you must carefully follow a 2 step process 1 Wheel Reinstallation 2 Follow up Step 1 Wheel Reinstallation During wheel reinstallation the lug nut torque must be applied in 3 stages This will ensure the wheel studs are centered in the wheel holes and will help the lug nuts maintain proper torque iF Start all lug nuts by hand Stage 1 Set your torque wren
4. Tire industry standards require that tires with the ST designation are speed restricted to 65 MPH under normal inflation and load conditions Unless a different speed restriction is indicated on the sidewall of the tire it is best that you not operate your trailer at speeds above 65 mph NOTICE Although tires designated LT are sometimes used on trailers they are not recommended for use on your trailer and should not be considered as replacements for the original equipment ST designated tires 69 Chapter 10 Tire Safety Information 70 water storage tank of 100 gallons this tank when filled would weigh about 800 pounds If more cargo is being transported water can be off loaded to keep the total amount of cargo added to the vehicle within the limits of the GVWR so as not to overload the vehicle Understanding this flexibility will allow you the owner to make choices that fit your travel and camping needs When loading your cargo be sure it is distributed evenly to prevent overloading front to back and side to side Heavy items should be placed low and as close to the axle positions as reasonable Too many items on one side may overload a tire The best way to know the actual weight of the vehicle is to weigh it at a public scale Talk to your RV dealer to discuss the weighing methods needed to capture the various weights related to the RV This would include weights for the following axles w
5. As with seals check the sealant around the windows at least once every six months If any interior leaks are noticed contact an authorized dealer immediately To ensure window operation adjust and lubricate latches and any moving parts annually A light oil or powdered graphite can be used for lubrication Periodically use a vacuum attachment to clean any debris out of the window weep holes which are necessary to drain any condensation or moisture from hard driving rains that may collect Frame and Chassis Frame and Bumper Over time weather and climate such as rain snow salt etc lead to corrosion Rinse the undercarriage wheel wells hitch and bumper when needed to remove dirt oil tar salt and other debris Periodically inspect for rust Near coastal regions inspect more frequently If needed lightly sand and repaint with a rustproof enamel Steps Clean regularly to remove dirt salt mud etc and lubricate pivot points with a quality automotive grade lubricant every 30 60 days Seal any nicks or scratches with primer and then cover area with a quality high gloss paint to prevent rusting If rust is noticed sand the area lightly and then cover with primer Follow with high gloss paint Hitch Couplers Inspect prior to each trip The ball socket and clamp should be cleaned and lubricated monthly with wheel bearing grease If coupler or coupler components appear damaged or worn contact your dealer upon notice of th
6. Loading and Weighing chapter in this Owner s Guide During transit secure motorized vehicles and motorized equipment so that items do not move while in transit Remove carpet from section where fueled vehicles or motorized equipment will be stored Loading Technique Ramp Positioning The ramp angle from the trailer floor to the ground affects the risk when loading unloading cargo If the ramp angle is reduced and all other conditions remain the same risk is reduced Always try to reduce the loading ramp angle the shallower the ramp angle the easier cargo loading will be Position the trailer to take advantage of any terrain features that will help reduce the ramp angle In all cases be sure the ends of the ramp door can be fully supported Always position the loading ramp so the ends in contact with the ground are level or at the same height An uneven ramp may cause the cargo to tip over sideways during loading unloading Loading Under Power Motorized cargo should be walked up the ramp When preparing to load the vehicle into the trailer the operator s hands should be positioned on the controls so as to keep the vehicle in control during loading 1 Shift into lowest gear before ascending ramps 2 Align wheels with ramps both loading and unloading 3 Approach straight on not on an angle If you are off to one side and the ground is uneven where the ramp touches the ground an unbalanced situation ca
7. 7 Back truck slowly until kingpin engages the fifth wheel and automatically locks 8 Ensure the lock is closed 9 Connect the power seven way cord between the tow vehicle and the fifth wheel 10 Connect the emergency breakaway switch cable 11 Test the fifth wheel brakes and exterior lights 12 Completely raise the landing gear 13 Chapter 2 Towing and Levling Excessive sway or fishtailing of your travel trailer can lead to the rollover of the trailer or tow vehicle Serious injury or death can occur It is important that you read and understand the information in this section Check tires for proper inflation and wheel lug torque to meet manufacturer s specifications 14 13 Store the wheel chocks 14 Check the tire pressure while the vehicle tires are cold 15 Re torque the lug nuts Refer to Wheel Nut Torque Notes Before Towing e Ensure the TV antenna is down and in the correct position e Disconnect all park connections and are securely stored e Close and secure all doors windows awnings and roof vents e Return the Entry step to the travel position e Refer to the Pre Travel Checklist located in the Appendix Towing Towing a recreational vehicle can be enjoyable and worry free if special attention toward safety is applied every time you hit the road and before heading out on our first camping trip practice turning stopping and backing in low traffic areas or l
8. B For Winterization Procedures RV Anti Freeze with ez winterizing system See the section Winterization With By Pass Kit Installed in this chapter 1 Purchase 4 6 gallons of RV approved non toxic anti freeze 2 Drain all tanks fresh water and sewage tanks 3 Turn water heater by pass valve to by pass position The by pass valve is located near the water heater incoming lines an 41 Chapter 6 Plumbing System 42 access panel may have to be removed depending upon the model 4 Drain water heater 5 If installed remove water filter from assembly and discard Install diverter if included 6 Locate the ez winterizing system found near water pump or on some models in water management panel Turn valve to close flow from fresh tank and allow flow from ez winterizing hose Place hose into supply of anti freeze 7 Turn on pump switch and open the cold water side of all faucet fixtures Leave open until the anti freeze comes out generally pink in color Repeat for hot water side 8 Flush toilet until anti freeze begins to flow into the bowl and then pour one gallon of anti freeze down the toilet to winterize the black tank 9 Pour anti freeze down each shower tub lavatory sink and kitchen sink to fill p traps 10 To winterize gray tank s pour one gallon down each related sink drain De winterization Removal of Anti freeze If purchasing a coach which is winterized with RV anti fr
9. Chapter 11 Ramp Trailers 83 Appendix 84 Appendix For assistance with this manual warranty information or information on Redwood Products please contact your dealer or visit us on the web or contact Redwood RV Company Retail Customer Service Address Redwood RV Company Customer Service Dept 1115 West Lake St Topeka IN 46571 Fax Phone E Mail Web 260 593 2815 260 593 2866 service redwoodrv com or service 1 redwoodrv com www redwoodrv com Business Hours 8 30AM 5 00PM EST Monday Friday Exterior Pre Travel Checklist Fill the Propane bottles Empty the holding tanks Connect the trailer to the tow vehicle and test all of the exterior lights Inspect the awning and ensure that it is properly retracted and secured for travel It is recommended that a tie wrap be used on the awning arms preventing the possibility of the awning deploying while in travel Inspect all exterior baggage doors and hatches ensuring they are locked Inspect the tires and check the pressures Refer to Chapter 9 Loosen and Torque the lug nuts Refer to Chapter 9 Connect the breakaway switch and test the brakes on the trailer Adjust the tow vehicle brake controller in accordance with the manufacturer s recommendations Secure the rear leveling jacks in the up position Position the battery disconnect to the on position This is required to engage the trailer s brakes in the event of an emergency Ensure
10. 50 Amp and Available Power 50 Amp Capability 30 Amp service has a three prong cord while 50 Amp utilizes a four prong With the 30 Amp plug only one prong carries the I20V power With the 50 Amp plug two of the four plugs carry 120 Volt allowing for the ability to set up power needs according to appliance application As such if your unit has 50 Amp service two air conditioners can run at the same time if they are routed on different feeds while running other appliances commonly used within an RV If your unit has below 50 Amp service alternate appliance use according to the chart above to prevent popping breakers AMPERAGE APPLIANCE CONSUMED Roof Air Conditioner Continuous Roof Air Conditioner Initial Start Electric Water Heater Microwave Converter Refrigerator TV or VCR Hair Dryer 110 Volt Light Available Power Despite the power system built into a recreational vehicle the power system is only as good as the power supply If the campground has only 30 amp service available an RV with 50 amp service will only be able to use 30 amps of service Some campgrounds have only 15 amp service available which is not adequate to properly run an air conditioner or certain other appliances See chart above The best way to know what amperage is available is to call ahead to the campground There are special adaptors available through your local Redwood dealer to make these connections to campgrounds with lower service rat
11. ST tires are speed restricted to 65 mph Never operate a vehicle in an unsafe or unlawful manner Tire speed ratings if indicated should never be associated with the ability of the vehicle to handle the speed for which the tire is rated U S DOT Tire Identification Number This begins with the letters DOT and indicates that the tire meets all federal standards The next two numbers or letters are the plant code where it was manufactured and the last four numbers represent the week and year the tire was built For example the numbers 3197 means the 31st week of 1997 The other numbers are marketing codes used at the manufacturer s discretion This information is used to contact consumers if a tire defect requires a recall Tire Ply Composition and Materials Used The number of plies indicates the number of layers of rubber coated fabric in the tire In general the greater the number of plies the more weight a tire can support Tire manufacturers also must indicate the materials in the tire which include steel nylon polyester and others Maximum Load Rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire Maximum Permissible Inflation Pressure This number is the greatest amount of air pressure that should ever be put in the tire under normal driving conditions Vehicle Load Limits Determining the load limits of a vehicle includes more than understanding the load limit
12. each Tiedown Track Load Rating 4000 Ibs per track Cargo floor tiedown rail 73 Chapter 11 Ramp Trailers 74 Always hitch the trailer to the tow vehicles and use wheel chocks or other vehicles restraining devices when loading and unloading the trailer Keep spare chocks on hand They often get left behind or lost during outdoor activities Chocking the wheels of a truck trailer or other piece of mobile equipment provides a physical stopper to the wheels to prevent runaways that can crush and injure people and damage equipment When chocking use wheel chocks of the appropriate size and material to securely hold the vehicle Don t use lumber cinder blocks rocks or other make shift items to chock Make it easy to find and use the correct chocking equipment store chocks inside the trailer or tow vehicles Keep chocks available at places where you typically load and unload Use extra caution when loading from the ramp If the trailer rolls away you and the equipment you are loading can fall with severe injuries or death Never load equipment from the ramp into the trailer until you unsure that the wheels are properly chocked Ensure that the trailer floor is in good condition and that it can support the weight of the equipment you are loading Blocking stabilizes loaded cargo to prevent shifting and trailer overturns If the load shifts while in motion the sudden shift in position and center of gravity may ca
13. s Guide Never exceed the GAWR and GVWR ratings of either your trailer or your tow vehicle Connect to the tow vehicle and use wheel chocks in addition to the forward landing gear jack of spotted trailers when loading and unloading to prevent potential forward or backward movement when loading or unloading Be sure the work loading area is well lit Avoid loading unloading at night or in conditions of poor visibility Do not allow anyone who is not engaged in loading or unloading to be inside the trailer cargo area while loading unloading Visually inspect the trailer before loading A damaged spot in the floor can cause cargo to be unstable and damaged or missing tie down rings will prevent you from securing your load properly Use caution tape traffic cones or portable barricades to designate staging and loading areas in high activity situations where other vehicles and or pedestrians are present Keep the loading area clean and free of clutter and debris Clean up water and oil on the floor Designate areas at your campsite or activity area for storage of trash tools equipment supplies and expendable containers such as food beverage oil and fuel containers Give special attention to large loads that may obstruct the view of the loading crew Wear boots that provide adequate ankle support and slop resistant tread design and hand protection when loading unloading Always communicate with
14. see Thermostat in this section Chapter 2 Towing and Level After market stabilizer stands must be placed only under chassis frame rails Stabilizer jacks should not be placed at extreme corners of the frame Locating stabilizers in these locations can cause slide room damage if leveling blocks were to shift or settle Do not attempt to level raise or otherwise place all of the weight of the unit on the stabilizer jacks Do not use stabilizer jacks for tire changing ing 19 Chapter 3 Appliances and Equipment Portable fuel burning equipment including wood and charcoal grills and stoves must not be used inside the recreational vehicle The use of this equipment inside the recreational vehicle may cause fires or asphyxiation When refueling tow vehicle shut off all Propane gas appliances Most Propane gas appliances are vented to the outside Gasoline fumes could enter the appliance and ignite from the burner flame causing an explosion or fire Propane Gas containers shall not be placed or stored inside the vehicle Propane Gas containers are equipped with safety devices that relieve excess pressure by discharging gas to the atmosphere DO not store or use gasoline or other flammable vapors and liquids in the vicinity of any appliance Aa NOTICE Never run the A C without the filter This could plug the unit evaporator cell substantially effecting performance 20
15. storage area will affect the weight distribution of the recreation vehicle Adding weight to the unit behind the rear axle will reduce the weight to the front axle This may adversely affect handling of recreation vehicle while in transit Adding the weight behind the rear axle also adds to the weight load on the rear axle Do not over load the rear axle weight rating DANGER Cohabiting with an internal combustion engine vehicle can be hazardous to your health Fumes from fuel can cause fire explosion or asphyxiation Liftgate This is not a personnel lift Do not stand on or near lift when in motion Serious injury or death may occur Fold Down Ramp Keep all personnel clear of ramp working area while raising or lowering Keep all objects clear of pinch points when raising and lowering platform Keep the loading area clean and free of clutter and debris Keep the ramp and floor dry by cleaning up all spilled water oil and fuel as soon as possible The fold down ramp gives complete access to the cargo area When lowered the ramp allows easy loading of rolling cargo bicycles motorcycles ATV s and other small vehicles Always wear shoes that provide good traction and do not wear sandals or other types of slip on footwear when ascending or descending the ramp NOTE Refer to the fold down ramp manufacturer s operations manual for detailed information regarding the proper usage of the fold down ramp
16. If pressure builds too high within the regulator it vents until pressure reaches a normal range Check the vent frequently to keep the vent clean and clear of any debris corrosion or obstruction A clogged regulator can result in higher pressures loss of fuel and or component failure The vent can be cleaned by using a toothbrush and should be checked periodically by a qualified Propane service center Bottle Systems Primarily on Fifth Wheels Redwood uses Propane cylinders equipped with a safety valve to prevent over filling the tank Rapid changes in pressure during filling or when switching the regulator changeover valve can cause this safety feature to activate causing a no gas flow situation The problem occurs when the system downstream of the cylinder valve and above the regulator has less pressure than the bottle pressure The check valve activates sensing a break in the line In order for the valve to reset the pressure in the line must equalize with the tank pressure Internal mechanisms allow for a very small bypass flow to achieve equalization This usually takes 2 5 minutes Filling instructions for the split bottle system are on the following page Filling Propane Gas Bottles Redwood Propane systems are equipped with a Type cylinder connection making them as easy to connect and disconnect as a garden hose The Type I connection system uses the Excess Flow Pigtail Hose distinguished by the large green
17. ON TIRE The load on an individual tire that is determined by distributing to each axle its share of the curb weight accessory weight and normal occupant weight distributed in accordance with Table of CRF 49 571 110 and dividing by 2 WEATHER SIDE The surface area of the rim not covered by the inflated tire WET WEIGHT Weight of the coach with fuel fresh water and Propane tanks full WHEEL CENTER MEMBER In the case of a non pneumatic tire assembly incorporating a wheel a mechanical device which attaches either integrally or separably to the non pneumatic rim and provides the connection between the non pneumatic rim and the vehicle or in the case of a non pneumatic tire assembly not incorporating a wheel a mechanical device which attaches either integrally or separably to the non pneumatic tire and provides the connection between tire and the vehicle WHEEL HOLDING FIXTURE The fixture used to hold the wheel and tire assembly securely during testing Appendix 91 Index 92 Index 110 Volt System 30 12 Volt System 29 7 Way Plug 32 Air Conditioner 19 20 23 30 31 47 60 62 Antenna 20 Awning 21 Battery 16 28 29 31 33 35 39 45 46 49 53 54 64 85 86 89 Brakes 7 13 17 32 33 53 70 76 84 85 89 Breakaway Switch 13 16 33 34 84 Carbon Monoxide Detector 24 28 Condensation 7 8 28 48 60 62 86 Convection Oven 25 Converter 22 29 31 35 86 Fan Tastic V
18. Tire Fundamentals 67 Tire Label Information 67 Vehicle Load Limits 69 Cargo Capacities 69 How Overloading Affects Your RV and Tires 70 Tire Safety Tips 70 Chapter 11 Ramp Trailers ft Ramp Trailer Weight Distribution 71 Ramp Trailer Loading 71 Ramp Trail Loading Safety 71 Chocks and Blocks 73 Cargo Placement and Restraint 74 Proper Use of Tiedowns 74 Tiedown Minimum Working Load Limit 74 Minimum Number of Tiedowns 75 Loading and Unloading Motorized Cargo 75 Loading Under Power 77 Secure The Load 78 The Safest Way To Unload Your Motorized Cargo 78 Fuel Transfer System 79 Fuel Transfer System Safety 79 Fuel Transfer System Operation 80 Portable Containers 81 Garage Area 82 Liftgate 82 Fold Down Ramp 83 Appendix B4 Exterior Pre Travel Checklist 84 Interior Pre Travel Checklist 84 Glossary of Common RV Terms 85 Index gre 4 Important Safety Precautions You ll find many safety recommendations throughout this section and throughout this manual The recommendations on these pages are the ones we consider to be the most important Do Not Allow Passengers to Ride in the Trailer During Travel The transport of people puts their lives at risk and may be illegal The trailer does not have seat belts therefore it is not designed to carry passengers Reducing Fishtailing or Sway Sway or fishtailing is the sideways action of a trailer caused by external forces Excessive sway of your travel trail
19. a damp cloth Grease or oil based stains and spots should be spot cleaned with a good commercial spot cleaner made for this purpose If complete shampooing is desired it is best to have it done be a competent professional carpet cleaner Never soak or water log your carpeting Ceilings and Walls Clean only with a mild detergent in warm water using a damp cloth to clean the ceiling Never use strong chemicals or excessive water moisture as either can damage the ceiling or walls Countertops Most countertops are made of high pressure plastic laminates and are highly resistant to normal spills and scuffs Soap and lukewarm water or a mild non abrasive cleaner are recommended Avoid use of abrasive pads and scouring powders which can dull the surface and make it more stain prone Always use a chopping block or cutting board when using knives Pots and pans straight from the burner or oven should be placed on lined hot pads and not directly on the counter surface Solid Surface Countertops The solid surface composite countertops can be cleaned with soap and mild detergents which will remove most stains Do Not Use products containing bleach Stubborn stains may require the use of a white Scotch Brite pad and a non abrasive cleaner like Soft Scrub Scratches may be removed carefully using a green Scotch Brite pad and an abrasive cleaner like Ajax or Comet Cover an area large enough to blend the area needing repair using a circular mo
20. and DON TS e Do Use Automotive Marine grade non abrasive waxes e Do Use Soft cloths to clean and wax e Do be careful around graphics Wax and wash with the graphic not against it e DO NOT USE products containing ammonia or caustic harsh cleaners as they may cause discoloration to the fiberglass surface e Do Not use high pressure washers rotating brushes such as in car washes and power buffers Use of these products can damage graphics and or paint finishes e Do not dry wipe surfaces e Do not use rubbing compounds ABS Plastic Molded Parts Some components of Redwood products are constructed of strong ABS molded plastic A mild solution of soap and water should be used when cleaning When using any product make sure the product is recommended for use on plastics Avoid harsh abrasive cleaners ammonia or citric based products as discoloration may result Carefully read the component manufacturer s manual for complete instructions and any applicable safety instructions provided in the unit packet prior to performing any maintenance Roof The roofing system is a polymer membrane that will not rust or corrode and is quieter than metal roof systems The rubber roof material itself does not require annual coatings or additional sealants Wrinkles may develop in the material due to expansion and contraction from heating and cooling but this does not affect the integrity of the roof and is not a cause for concern Th
21. authorized dealer or repair facility anytime circumstances or conditions warrant but no less frequently than on an annual basis Refrigerator The refrigerator installed is a Propane gas appliance Carefully read the manufacturer s manual for complete operational and safety instructions provided in the unit packet prior to using the appliance Operation The refrigerator operates on either 120V AC or Propane Gas and has a gravity based cooling system This system requires that the recreational vehicle be level for efficient operation The cooling coils are sloped to allow continuous movement of the liquid chemicals and if the unit is not level for extended periods the flow of these chemicals will slow and pool inside the tubing resulting in a loss of cooling During towing the leveling is not as crucial as the movement of the trailer will prevent the liquid inside the tubing from pooling If needing to park for several hours the trailer should be leveled if operating the refrigerator or the refrigerator needs to be turned off Placing a small bubble level inside of refrigerator will assist in determining if level for operational efficiency When starting the refrigerator for the first time or after extended storage allow up to four hours for the cooling cycle to become fully operational Operational Controls Auto Mode The control system on the refrigerator will automatically select between gas and AC electric operation AC
22. dry the spill areas 81 Chapter 11 Ramp Trailers 82 DANGER When transporting gasoline in a portable container make sure it is secured against tipping and sliding and never leave it in direct sunlight or in the trunk of a car Garage Area Any motorized vehicle or any motorized equipment powered with flammable liquid can cause fire and explosion or asphyxiation if stored or transported within the recreation vehicle To reduce the risk of fire explosion or asphyxiation 1 Do not allow passengers to ride inside the internal combustion engine vehicle storage area while vehicles are present 2 Do not allow occupants to sleep in the vehicle storage area while vehicles are present 3 Doors and windows in walls of separation if installed must be closed while vehicles are present 4 Run fuel out of engine after shutting off fuel at the tank 5 Do not store or transport supplementary motor fuel within this vehicle 6 Ventilate the interior of the vehicle to reduce the risk of fire explosion or asphyxiation 7 Do not operate gas appliances pilot lights or electrical equipment when motorized vehicles or motorized equipment are inside the vehicle 8 Do not operate motorized vehicles while the rear door is closed Failure to comply could result in an increased risk of fire explosion asphyxiation death or serious injury Loading an internal combustion engine or other materials inside of cargo
23. frame This adjustment maximizes the life of your tires These adjustments require special equipment and should be performed by a qualified technician These adjustments are not performed at the factory and are not covered under warranty 66 The tire tread provides the gripping action and traction that prevents your trailer from slipping or sliding especially when the road is wet or icy In general tires are not safe and should be replaced when the tread is worn down to 1 16 of an inch Tires have built in tread wear indicators that let you know when it is time to replace your tires These indicators are raised sections spaced intermittently in the bottom of the tread grooves When they appear even with the outside of the tread it is time to replace your tires Tire Life Trailer tires may be worn out even though they still have plenty of tread left This is because trailer tires may have to carry a lot of weight all the time even when not in use It is actually better for the tire to be rolling down the road than to be idle During use the tire releases lubricants that are beneficial to tire life Using the trailer tires often also helps prevent flat spots from developing The average life of a trailer tire is about five years under normal use and maintenance conditions After five years trailer tires may be degraded to the point that they should be replaced even if they have minimal or no use Exposure to sunlight u
24. from the fresh water tank The toilet flushes directly into the black water tank Complete instructions and care for the model installed are located in the unit packet Chapter 6 Plumbing System Solid Build Up The most common problem associated with the waste system is solid build up Using plenty of water when flushing the toilet and keeping the tank valves closed until ready to flush the system can reduce the risk of build up Should you ever have a build up of solids close the valves fill the tanks about full with fresh water drive a distance to agitate the solids and drain the tanks Do not put these items in toilet or drains 1 Facial tissues paper towels sanitary products including those labeled flushable 2 Detergents or bleach Use a sewage tank deodorizer available from dealer 3 Automotive antifreeze ammonia alcohols or acetones 4 Grease from cooking table scraps or other solids that may cause clogging DANGER DO NOT USE Automotive Anti Freeze Automotive Anti Freeze Holding Tanks is poisonous and not for use in Waste water is divided into two categories Black water and gray water p systems The term black water refers to the waste flushed down the toilet and stored in a separate tank referred to as the black tank Gray water is the wastewater from the sinks tub and shower drains and is stored within one or more gray tank s Waste tanks empty through a single or 2 single depe
25. has expired or any performance of repairs to component parts and appliances that are excluded from coverage shall be considered good will repairs which shall not alter the express terms of this limited warranty Chapter 1 Warranty Chapter 1 Warranty Date 4 2011 Please have the following available when you call eVehicle Identification Number 17 digit Serial begins with 4V0 Model Date of Purchase Description of the problem ePrevious repair history and location if applicable Appliance and Component Warranty Service Appliance and component manufacturers may or may not provide their own warranties These warranties are separate from the Redwood Limited Warranty and constitute the only warranty for those specific appliances or components The terms conditions and warranty periods of these items may vary from the Redwood Limited Warranty For the appliance and component manufacturers providing warranties Redwood does however administer those warranties during the term of this Limited Warranty except for tires batteries and generators All warranty service claims on components may therefore be directed to Redwood during the Limited Warranty period After the warranty expires all appliance and component warranty claims must be directed to their respective manufacturer Redwood is not warranting any appliance or component and is only representing that it is authorized to administer the services
26. hitch HOLDING TANKS Refers to the tanks typically known as fresh water gray and black where the water is held HOOK UPS Where you connect to a campground s facilities INNERLINER The layer s forming the inside surface of a tubeless tire that contains the inflating medium within the tire INNERLINER SEPARATION The parting of the innerliner from cord material in the carcass INTENDED OUTBOARD SIDEWALL The sidewall that contains a white wall bears white lettering or bears manufacturer brand and or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle LIGHT TRUCK LT TIRE A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles Load rating The maximum load that a tire is rated to carry for a given inflation pressure LOAD RATING The maximum load that a tire is rated to carry for a given inflation pressure LOW POINT LOW POINT DRAIN Lowest point in the plumbing system Drain valves are placed at these points for sewage dumping Propane GAS Petroleum Gas Used to fuel appliances MAXIMUM LOAD RATING The load rating for a tire at the maximum permissible inflation pressure for that tire MAXIMUM PERMISSIBLE INFLATION PRESSURE The maximum cold inflation press
27. household detergents can be used for normal cleaning Do not use petroleum solvents harsh abrasives or citric based cleaners that can damage the membrane Appropriate cleaners such as Dicor Roof Cleaner are available through your dealer Remember to rinse thoroughly after cleaning For stubborn stains a cloth dampened with mineral spirits is suggested Do not however pour mineral spirits directly onto the roof material or allow a stain to soak Keeping the roof free of debris and clean will help prevent staining Avoid parking in areas where fruit or tree sap may fall and remain directly on the roof for extended periods causing irremovable stains Seals and Adhesives The seals and adhesives used perform an important job keeping out an RV enemy water Close inspection and routine maintenance are crucial to the longevity of the trailer While many types are used none have a pre set lifetime as exposure to the elements and regional variances of climate can accelerate any sealants deterioration Therefore every six months inspection of all seals is recommended and a quick inspection prior to every trip will help reduce potential problems down the road When inspecting check for cracks voids shrinkage or any sign of deterioration If any of these signs are noticed have your dealer inspect and replace the sealant if necessary It is important to use the same kind of sealant that was previously used Windows Exteriorj
28. instructions and recommendations to the use and cleaning of the dehumidifier Chemical Sensitivity After you first purchase your new recreational vehicle and sometimes after it has been closed up for an extended period of time you may notice a strong odor and chemical sensitivity This is not a defect in your recreational vehicle Like your home there are many different products used in the construction of recreational vehicles such as carpet linoleum plywood insulation upholstery etc Formaldehyde is also the by product of combustion and numerous household products such as some paints coatings and cosmetics However recreational vehicles are much smaller than your home and there fore the exchange of air inside a recreational vehicle is significantly less than a home These products when new or when exposed to elevated temperatures and or humidity may off gas different chemicals including formaldehyde This off gassing in combination with the minimal air exchange may cause you to experience irritation of the eyes nose and throat and sometimes headache nausea and a variety of asthma like symptoms Elderly persons and young children as well as anyone with a history of asthma allergies or lung problems may be more susceptible to the effects of off gassing Formaldehyde Most of the attention regarding chemical off gassing surrounds formaldehyde Formaldehyde is a naturally occuring substance It is also a key indust
29. of anti freeze that will be needed by pass kits are available at most RV service centers for a reasonable expense and can be installed during winterization Without a by pass kit installed an additional 6 10 gallons of anti freeze will be required On the following page are the procedures for both methods Your local dealer is best suited to answering any questions as well as providing information on winterization and storage that may be particular to the climate in your area If using the compressed air method a special adapter should be purchased to allow compressed air to be delivered through the city water fill These adapters are available at most RV supply stores Chapter 6 Plumbing System Method 1 Compressed Air With By Pass Kit Installed 1 Purchase 1 2 gallons of RV non toxic anti freeze Drain the fresh water tank and empty the waste water holding tanks 3 Turn water heater by pass valve to by pass position The by pass valve is located near the water heater incoming lines an access panel may have to be removed depending upon the model 4 Drain water heater 5 If installed remove water filter from assembly and discard Install diverter if included 6 Open all faucets including shower head sprayer toilet flushing device and any other water lines that are closed 7 Turn on the water pump for 30 seconds to clear out any water in the lines 8 Connect an air hose with an adapter to the city wat
30. of the chains once attached to the tow vehicle frame They should be long enough to allow for turns but short enough to avoid any drag Chapter 2 Towing and Leveling 15 Chapter 2 Towing and Levling Disconnect the unit from the Seven Way Tow Vehicle Cord prior to testing the breakaway switch Failure to do so may cause damage to the brake controller 16 Breakaway Switch The breakaway switch is another safety device as it provides a means of automatically slowing and stopping your RV if it should become detached during traveling The cable from the breakaway switch should be attached to the tow vehicle so that it remains connected in the event the trailer coupling detaches from the hitch ball The breakaway switch is powered from the RV 12 Volt battery If separation occurs the pin is pulled out of the switch and current from the RV battery is applied to the trailer brakes Tire Pressure Maintaining proper tire pressure is another key to safety The Cold Inflation Pressure for each axle is located on the Federal Certification Label Cold inflation pressure refers to the pressure in the tire prior to traveling Always check your tire pressure before traveling Under inflated tires will cause excessive sidewall flexing and produce extreme heat leading to early tire failure and possible loss of control Over inflated tires can cause uneven tire where and also lead to early failure More information on tire
31. on the specific component installed If malfunction occurs immediately call your local dealer Service on any jack should be performed by qualified service personnel only Chapter 8 Care amp Maintenance Glass breakage is not covered under our limited warranty Rust is not covered under our limited warranty 49 Chapter 8 Care amp Maintenance If equalizer weight distribution bars are attached to vehicle while attempting to operate a power tongue jack the motor may clutch and or seize upon attempting to bear the load Damage to the jack under these circumstances will not be covered by Redwood RV Company or the jack manufacturer Some procedures require the use of special tools for safe and correct maintenance Do not attempt to service repair or work on any axle brake or wheel system unless you have appropriate skills and knowledge Lack of proper training failure to follow procedures or use special tools and safety equipment could result in property damage serious injury or loss of life 50 Carefully read the component manufacturer s manual and any safety instructions provided in the unit packet prior to performing any maintenance Tires and Wheels The tires should be checked before starting out on any trip See chart on following page Check them regularly and keep inflated to recommended pressures The recommended tire pressure is on the side of the tire A ti
32. operating in harsh environments road salt ice build up etc the moving parts be kept clean and can be washed with mild soap and water No grease or lubrication is necessary and in some situations may be detrimental to the environment and long term dependability of the system Electrical System Maintenance For optimum performance the slideout system requires full battery current and voltage The battery must be maintained at full capacity Other than good battery maintenance check the terminals and other connections at the battery the control switch and the electric actuator motor for corrosion and loose or damaged terminals Check motor leads under the trailer chassis Since these connections are subject to damage from road debris be sure they are in good condition Mechanical Maintenance Although the system is designed to be almost maintenance free actuate the room once or twice a month to keep the seals and internal moving parts lubricated Check for any visible signs of external damage after and before movement of the travel trailer Additional information can be found in the manual for this slideout system or at www lici1 com Electrically Operated Systems The Lippert Electric Slide out System uses a 12 Volt DC motor to power the rack and pinion style slide system room s Electricity for the motor assembly is supplied by the coach battery Normal operation is performed by pressing the wall mounted slide out switch t
33. state An odorant similar to rotten egg smell has been added for consumer safety purposes to help detect leaks and provide warning Propane gas is highly flammable and is contained under high pressure Improper use may cause fires and or explosions If a sulfur or rotten egg smell is detected in or around the trailer perform the following steps immediately What to do if you smell gas Do not try to light any appliance Extinguish any open flames including cigarettes Do Not Touch Any Electric Switch Open windows and doors Exit trailer Shut off the gas supply at the gas container bottle or source Immediately call a service center or gas supplier from an outside phone and follow their instructions Do not turn on the gas supply until the gas leaks have been repaired Propane Regulator The regulator is the heart of the Propane system Propane gas is under high pressure in the bottle and the regulator reduces this pressure to allow safe use with the appliances in recreational vehicles The lower pressure is distributed to the appliances The arrow on the automatic gas regulator will always point to the gas bottle in service When the red flag appears in the inspection glass this indicates that bottle is empty In systems without automatic changeover the arrow should be then turned toward the other bottle and the empty filled as soon as possible Care and Maintenance The regulator has a vent that allows it to breath
34. temples Weakness and sleepiness Inability to think coherently If you or anyone else experience any of these symptoms get to fresh air immediately Shut the generator down and do not operate it until it has been inspected and repaired by a professional If the symptoms persist seek medical attention 1 DO NOT operate the generator while sleeping You would not be aware of exhaust entering the recreation vehicle or alert to symptoms of carbon monoxide poisoning 2 Never store anything in generator compartment Always keep compartment clean and dry 3 DO NOT operate the generator in an enclosed building or in a partly enclosed area such as a garage 4 Review the safety precautions for fuel and exhaust fumes elsewhere in this manual 5 DO NOT operate the generator when the recreation vehicle is parked in high grass or brush Heat from the exhaust could cause a fire in dry conditions 6 Never operate your chassis or generator engine or the engine of any vehicle longer than necessary when the vehicle is parked 7 DO NOT simultaneously operate generator and a ventilator which could result in the entry of exhaust gas When exhaust ventilators are used we recommend that a window on the opposite side of the unit upwind of exhaust gases be opened to provide cross ventilation 8 When parked orient the vehicle so that the wind will carry the exhaust away from the vehicle DO NOT open nearby windows ventilators or doors
35. the person doing the loading Know what the plan is and make sure you agree Maintain eye contact with other persons involved at all times during loading unloading making sure they know where you are Slow down and pay attention never hurry around loading unloading operations Train everyone in your travel group on the hazards of loading and unloading Establish and enforce compliance to all safety procedures Chocks and Blocks Chocks and blocks prevent accidental or unintended movement of mobile equipment and cargo while you are loading unloading hitching unhitching or performing service or maintenance Wheel chocks are wedge shaped blocks placed in front of or behind the rear wheels of a trailer or tow vehicles to prevent the trailer from moving while the trailer is being loaded Trailer creep occurs when the sideways and vertical forces exerted each time a load enters and exits the trailer cause the trailer to slowly move away from the loading area The weight and speed of loading can affect trailer creep The grade the trailer is parked on the softness of the suspension and whether the trailer has been dropped off or of it is still connected to the tow vehicle are also factors Loading accidents can also occur when a driver prematurely pulls away while the trailer is still being loaded unloaded Chapter 11 Ramp Trailers Ramp Door Load Limit 2000 Ibs total Tiedown D ring Load Rating 1500 Ibs
36. the steps are retracted Interior Pre Travel Checklist Close all vents and windows Place the television antenna down position Retract the slide rooms Inspect the interior of the unit ensuring that all cabinet interior and the shower doors are closed and secured Secure all loose items in storage compartments Ensure that the travel latch is closed on the refrigerator Test the smoke carbon monoxide and Propane alarms Battery Check the electrolyte levels in the battery cells Refer to Chapter 5 Clean the battery terminals and ensure they are securely tightened Refer to Chapter 5 Exterior Wash and wax the exterior of the coach at least monthly Pay particular attention to the graphics when washing and waxing Power buffers and high pressure washers can remove or damage the graphics This type of damage is not covered under the warranty Refer to Chapter 9 Inspect the seals around the windows doors and appliance vents Clean and reseal as required Refer to Chapter Remove debris from the window weep holes Refer to Chapter Frame and Chassis Inspect the frame for signs of corrosion Clean and lightly sand any corroded areas and touch them up with good quality paint Refer to Chapter 9 Inspect the steps for corrosion Clean and touch up any corroded areas Lubricate the pivot points on the steps Refer to Chapter 9 Check the tire pressure Refer to Chapter 9 Generator Review the preventative maintenance require
37. to OFF 1 Make sure antenna is fully raised 2 Pull down on lower ceiling plate with both hands until it disengages and will turn 3 Slowly rotate clockwise or counterclockwise for best picture and sound To Lower Antenna 1 Rotate antenna until pointer on directional handle aligns with pointer on ceiling plate 2 Turn elevating crank counterclockwise in DOWN direction about 13 turns or until resistance is felt Antenna is now locked in travel position A patio awning is a very popular accessory on recreational vehicles They provide additional living area for your campsite as well as protection Redwood RV Company uses several awning models The appropriate instructions for the equipped awning are included in the unit packet Please review the manufacturer instructions carefully prior to using the patio awning Care and Maintenance The best way to extend the life of the awning is to keep it clean and operating smoothly At the start of every camping season or after extensive traveling inspect the top and bottom brackets and tighten if loose Moving parts such as the lift handle rafter and support arms may become hard to operate due to weather exposure and use If this occurs spray the part s with a silicone spray To keep the awning operation smooth repeat the process on a regular basis Mold and mildew on the fabric can be avoided by periodically cleaning the vinyl with a mild non abrasive clean
38. tow the trailer with missing lug nuts or faulty lug bolts It is critical that the wheels be properly torqued every 50 miles during the first 200 miles of road operation Although the wheels have been properly torqued before leaving the manufacturing plant settling and wearing in of components during the first few miles of operation may cause some loosening of the wheel nuts Installation of wheels which are not compatible with the manufacturer installed axle assembly could result in wheel separation which can lead to property damage serious injuries or loss of life 53 Chapter 8 Care amp Maintenance When storing a battery do not place the battery directly on concrete as the battery will discharge more rapidly The acid in batteries is highly corrosive and hydrogen gas is produced which is extremely flammable Avoid placing near a possible ignition source such as open flame or potential spark producing wiring Before performing any maintenance on the battery always disconnect the battery removing the negative cable first and then disconnecting the positive Always disconnect the negative cable prior to working near batteries to reduce risk of arching and igniting 54 Tap water contains minerals and chemical impurities that will permanently damage the battery Besides maintaining the electrolyte level visually inspect the battery for loose terminals corrosi
39. washing in hot soapy water Frequency of cleaning is dependent upon range usage The range or cook top installed is a Propane gas appliance Carefully read the manufacturer s manual for complete operational and safety instructions provided in the unit packet prior to using the appliance Range Cook Top Operation Top Burners Range or Cook topj Prior to Lighting Assure the gas supply to the trailer is turned on Open a window and or vent for ventilation purposes Check for any hazards flammable liquids fabrics objects near burners If gas smell is present Do Not Light See What to do if you smell gas Depress knob corresponding to burner to be lit and turn to Lite position Immediately Light Burner Match Light Models Hold a long match or a hand held igniter near the burner port Make sure the hand held igniter is the type designed for open flame burners Piezo Ignition Models Rotate the Piezo knob clockwise rapidly This will produce a Spark to ignite the gas After lighting adjust burner flame to needed level If flame on burner goes out after initial lighting or during cooking turn burner knob to off and wait 5 minutes before attempting to relight Before attempting to relight check to make sure gas smell has disappeared If Propane powered appliances produce carbon monoxide Carbon monoxide can be fatal When the device detects carbon monoxide in the air it will sound Cons
40. will always be selected if available If AC becomes unavailable the refrigerator will switch to gas mode operation When in auto mode the indicator lamp on the control panel will be lit Gas Mode This mode when selected provides gas operation only The indicator lamp for auto mode will not be lit Care and Maintenance Exterior Ventilation of the refrigerator is essential Make sure the vents are clear of any obstructions such as bird insect nests spider webs or any other debris Periodically clean the coils on the back of the refrigerator with a soft bristled brush At no time should any combustible materials such as gasoline flammable liquids or vapors be stored near the refrigerator Interior When cleaning the interior lining of the refrigerator use a weak solution of soda and warm water Use only warm water however when cleaning the finned evaporator ice trays and shelves Never use harsh chemicals or abrasive cleaners to clean these parts or their protective coatings will be damaged Defrosting When defrosting the refrigerator shut off the power by turning the main power button to the off position Remove any food and leave the drip tray under the finned evaporator Remove light bulb or cover switch with a piece of tape Leave the door s open and empty drip pan when necessary Dry with a soft cloth when done Chapter 3 Appliances and Equipment When refueling tow vehicle shut off all Propane
41. Chapter 2 Towing and Levling 12 Weight Ratings Labels A TE EGE COMPOS TO L ALGAE STAR PRESSDDEO DUDEN TEE CULLIN MOTE VESELE SAFETY REGULATIONS Ul GETT Qa Tee DATE OF MANOHACTURE GE VERNGULE EST compii DATES LES DORMES GAI LDI SATT APPLIANCES EN YENTE DO MGLE A LA GECUIRITE MS TEELE MOTOR ES DO ALADA Ea REETA d LA DATE DE EA PARBICATIME TAY TETEE FO 228 The information on the weight ratings is contained on two labels The Federal Certification Tag and the RVIA Weight Label Each label contains the Vehicle Identification Number VIN Serial Number for the vehicle rated These ratings are specific for each fifth wheel and travel trailer manufactured Use only the ratings found on these labels Fifth Wheel TAAIE Wench 1M PRATE Wi MA ARRAL SA ar AEE Ene AT Re ee le ee a Ge Or Tee TAL ee PL LOE DT MOLES A WAT AT Te TAALA Ap AT A F pE Cn APA O ER A es Te T BATEY IT UE UAL EH 1 LA eT OS TRALA A Gh a TAE A Pi iF APARE T A A eS FUL DPR RATA Fini iiaa y Fhe giai Cie A COAT ECC CANDO CARRIED CAPACI ry Bi FORLA TO aR A BAH OF THE P ai AAA UL PRESH aTa WEATER AT OO Leg BT EA HEATER AAL PGAR MEIH T CARGO CAMA YIM CAPACITY CoC COMPUTATION POLS ALO PALI LP GGG AORA THES TAANE ALE ST LED Enea AL UE COT Federal Certification Label Location The Federal Certification Tag on your fifth wheel can be located on the road side off door side near the front of the unit as seen in the d
42. E ku a v4 DR i 2 Bek ie Site Janes re SE nes E tn Pea ee it r fe A A E gt TA RESIDENTIAL VEHICLES Renwoop RV Owner s Gude FIFTH WHEELS Place an exterior picture of your unit here to personalize this Owner s Guide PLACE PHOTO HERE Notes Inspection and Service Certification VIN It is the owner s responsibility to have the following inspections and service items performed These inspections and services are at the owner s expense and failure to do so will void your structural warranty These inspections and services must be performed annually by a qualified Redwood RV dealership A 30 day grace period will apply to all annual inspections Please have the Inspection and Service Certification Form completed by the qualified Redwood RV dealer when service is completed Keep this original Inspection and Service Certification and fax mail a copy to Redwood RV Service Department annually when service is completed Dealer Service Department After performing the following services please complete the appropriate area below for warranty validation O 1 Inspect roof membrane for damage cuts tears etc and repair as required J 2 Inspect lap sealant on all roof appliances for cracks etc Replace or add sealant as required J 3 Inspect sealant on all windows and re seal as required O 4 Inspect all clearance light lenses for cracks and inspect seal around body of light Replace and reseal as required
43. IRE A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the center line of the tread BLACK TANK The holding tank into which the toilet directly drains BLACK WATER The term associated with sewage contained within the black tank BRAKE CONTROLLER Device located under the dash of a towing vehicle that controls the braking system of the fifth wheel BTU The measurement of the amount of heat required to raise the temperature of one 1 pound of water one 1 degree F CARCASS The tire structure except tread and sidewall rubber which when inflated bears the load CHUNKING The breaking away of pieces of the tread or sidewall CITY WATER Refers to exterior water source not water from the fresh water tank that you hook up to at campgrounds City Water refers to pulling water from a central source like in a city COLD INFLATION PRESSURE The pressure in the tire before you drive CONDENSATION The result of warm humid air coming in contact with cold glass also known as Sweat CONVERTER Device that converts 110V AC to 12V DC CURBSIDE Term used to refer to the side of your coach which faces the curb or shoulder when parked Also called DOOR SIDE the main entrance door or OFFROAD SIDE COLD INFLATION PRESSURE The pressure in the tire before you drive CORD The strands forming the plies in the tire CORD SEPARATION The
44. J 5 Inspect all exterior moldings for cracks in sealant and re seal as required Inspect visible screws in molding for rust or breakage Replace as required Inspect molding butt seams for sealant and apply as required O 6 Investigate for the presence of condensation in the roof cavity and document below If condensation is present correct as required and re instruct customer as to the hazards of condensation Ist Year _ Structural Warranty is defined in Chapter One Notes Introduction Introduction Dear Redwood Owner Thank you for purchasing a Redwood RV Company product Your decision to own a Redwood is what drives our efforts everyday and we appreciate your vote of confidence We want the experience with your new fifth wheel to be enjoyable To help get you started please take a few minutes and review our owner s manual It is pretty straight forward and will help you understand many of the functions and required maintenance of your RV On behalf of everyone at Redwood RV Company we hope you will enjoy our product as much as we have enjoyed creating it for you Your Redwood RV Company Team 1115 West Lake St Topeka IN 46571 Phone 260 593 2866 FAX 260 593 2815 www redwood rv com Redwood RV Company has provided this manual solely for the purpose of providing instructions about the operation and maintenance of its recreational vehicle Nothing in this manual creates any warranty either express or im
45. Push the vehicle backward in line with the ramp 4 As the rear tires start down the ramp let go of the vehicle and let it roll backwards don t try and slow or control the vehicle as this can cause injury Fuel Transfer System A fuel transfer system allows you to store gasoline for use in motorcycles snowmobiles ATV s or other vehicles and equipment while at a campsite This system consists of a fuel tank fuel tank filler fuel gauge fuel transfer pump fuel transfer valve and hose with fill nozzle A master pump switch is located on the inside control panel and an emergency shutoff switch is located on the trailer frame rail near the fuel transfer pump A metal ground clip reduces the possibility of static electricity discharge between the fuel station and the equipment being fueled To fill the tank removed the fuel filler cap and fill the tank with the grade of gasoline required by your equipment When replacing the fuel fill cap be sure it seats squarely and turn it firmly to lock it on the fill pipe neck Transfer System Safety Static electricity related incidents when refueling are extremely unusual They appear to happen most often during cool or cold and dry climate conditions In rare circumstances these static related incidents have resulted in a brief flash fire occurring at the fill point You can minimize these and other potential fueling hazards by following sage refueling procedures A build up of static ele
46. Warning Caution and Note Boxes 2 Chapter 1 Owner and Dealer Responsibilities Dealer Responsibility LIMITED WARRANTY Inspection Unit Information Packet Owner Registration 10 Obtaining Warranty Service 10 Get To Know Your Unit 5 Owner s Responsibility 5 5 5 9 9 Before Heading Out 10 If You Need to Make an Appointment 10 Chapter 2 Towing and Leveling 11 Towing Guidelines 11 Weight Ratings Definitions 11 Weight Ratings Labels 12 Federal Certification Label 12 RVIA Weight Label 13 Weighing Your Unit 13 Hitches and Towing 13 Towing 14 Before Heading Out 15 While Driving 16 Fifth Wheel Leveling Procedures 18 Ramp Trailer Weight Distribution 18 Stabilizing Jacks 19 Chapter 3 Appliances and Equipment 19 What to do if you smell gas 19 Air Conditioner Optional 19 Antenna TV 20 Awning Patio Optional 21 Awning Slide Out Optional 22 Cable Hook Up 22 Fan Tastic Vent Optional 22 Furnace 22 Fireplace Optional 23 Generator Optional 24 Microwave Convection Oven Optional 25 Range Cook Top 25 Refrigerator 27 Roof Vents 28 Safety 28 Propane Detector 28 Smoke Detector 28 Carbon Monoxide Detector 28 Chapter 4 Electrical System 29 12 Volt System DC 29 110 Volt System Also referred to as 120 AC 30 Power Cord Shore Cord 30 30 Amp 50 Amp and Available Power 31 Converter 31 GFCI Ground Fault Circuit Interrupter 32 7 Way Plug 32 Br
47. _ i LS GOT iii E hidi umi Prr Car jive Tien poy Lt l EL f f composition hn Tigi ang mhitaji i wil Treadwear traction and tampenniaee TREE Maaa bead aling Next number This three digit number gives the width in millimeters of the tire from sidewall edge to sidewall edge In general the larger the number the wider the tire Next number This two digit number known as the aspect ratio gives the tire s ratio of height to width R The R stands for radial Other tire designs may be bias ply or bias belted and are designated by other letters Next number This two digit number is the wheel or rim diameter in Maximum bong Load amp inflation when wased as a dual Severe snag Light conditions truck tirg Maximum load amp inflation when Load inflation ice aa A single limis inches If you change your wheel size you will have to purchase new tires to match the new wheel diameter Next number This two or three digit number is the tire s load index It is a measurement of how much weight each tire can support You may find this information in your owner s manual If not contact a local tire dealer Note You may not find this information on all tires because it is not required by law Speed Rating The speed rating denotes the top speed at which a passenger care tire is rated A speed rating will not be found on ST tires used on trailers All
48. ad evenly over the axles as much as possible Keep heavy items low and forward preferably in the lower storage areas This will produce a lower center of gravity and improve road stability Distribute the load evenly on each side of the trailer Place heavier objects opposite the heavier appliances cabinets furniture etc when possible Experiment with various load positions until you find the best distribution Avoid loading heavy items in our on the rear of the trailer This can cause both total weight problems and hitch weight distribution problems Secure items so they won t move around while traveling Make sure all items and materials are properly stored Close and latch all drawers cabinet doors and closet doors Pull all loose furniture away from cabinets and walls lay on their side or secure to prevent rubbing during travel Carry only as much water as you think you will need while traveling Water weighs over eight pounds per gallon Whenever possible empty the holding tanks before getting on the road Ifyou are heading for rough terrain use heavy packing material in the cupboards to hold plates glasses etc Put a nonskid material beneath heaver items to prevent shifting Expensive and breakable belongings should be well packed and placed on the floor in the center of the trailer as the center rides the best Store emergency items such as fire extinguisher first aid kit highway warning devices glo
49. akes Electric 33 Breakaway Switch 33 Chapter 5 Propane Gas System 33 General Information 33 What to do if you smell gas 34 Propane Regulator 34 Bottle Systems 34 Propane Gas Lines 35 Propane Gas Leak Detector 35 Chapter 6 Plumbing System 36 Water Pump 36 Fresh Water Tank 37 Water Heater 38 By Pass Kit 39 Monitor Panel 39 Winterization 40 Waste Water System 42 Holding Tanks 43 No Fuss Flush 44 Chapter 7 Slide Out Systems 44 Basic Slide Out Tips 44 Electrically Operated Systems 45 Chapter 8 Care and Maintenance 46 Exterior 46 Roof 47 Seals and Adhesives 48 Windows Exterior 48 Frame and Chassis 48 Tires and Wheels 50 Battery 53 Bedspreads 54 Blinds and Shades 54 Cabinet Doors and Drawers Wood 54 Carpeting 55 Ceilings and Walls 55 Counter tops 55 Draperies 55 Faucets and Fixtures 56 Flooring Vinyl 56 Glass and Mirrors 56 Fabric and Upholstery 56 Sinks Tubs and Toilets 56 Chapter 9 Chemical Sensitivity Ventilation To Avoid Condensation Problems Follow These Tips 60 About Molds 60 60 Chapter 10 Tire Safety Information 62 Tire Pressure Management System 62 Understanding Tire Pressure and Load Limits 64 Checking and Adjusting Tire Pressure 64 Tire Tread 65 Tire Life 66 Replacement Tires 66 Tire Safety Information 66 Safety First Basic Tire Maintenance 67 Finding Your Vehicle s Recommended Tire Pressure and Load Limits 67 Tire Repair 67
50. al appliances so as not to start under a load which could cause a breaker to open Reverse this process before unplugging The power cord prongs should always be clean and solid Clean with a contact cleaner emery cloth and or a nail file Electrical connections work better when clean 30 110 Volt System Also referred to as 120 AC The 120 Volt system is supplied by plugging the power cord shore cord into an outside source It furnishes current to the 120 Volt appliances and fixtures like the roof air conditioners the refrigerator lighting and all 110V receptacles It also supplies power for the 12 Volt trailer system through the converter The AC circuits are protected by circuit breakers and can handle from 15 to 30 Amps depending upon the circuit The most common cause of a circuit breaker to open is an overloaded circuit An example of an overloaded circuit is when a space heater is plugged into the same outlet as the toaster If this happens reduce the load on the circuit and reset the breaker Power Cord Shore Cord The power cord often referred to as shore cord or shoreline is a heavy duty cable with a 4 prong grounding plug on one end and connects directly to the power converter inside the unit on the other end This cord is used to plug into an external 120V source Do not plug shore cord in while under load Make sure all appliances are turned off prior to connecting shore cord
51. ance process described in section C Pre Trip Maintenance Summary 1 Check torque before every trip 2 Use proper tools 3 Follow the appropriate star pattern sequence 4 Torque lug nuts in the correct stages and follow up intervals after any wheel reinstallation Wheel Bearing Lubrication Wheel bearings should be repacked every 6000 miles or every 6 months Every time the wheel hub is removed the wheel bearings must be adjusted Turn the hub slowly to seat the bearings while tightening the spindle nut until the hub will no longer turn Loosen the spindle nut so it may be turned by hand Tighten nut finger tight then loosen to first hub slot allowing alignment Install cotter pin The spindle nut and hub should be free to move with the cotter pin being the only restraint Prepare bearings by cleaning with solvent to remove the old grease Repack by pressing fresh bearing grease into bearing roller area Repack bearings more often if subject to extremely wet conditions If trailer ha not been used for more than 2 months the wheel bearings should be inspected and repacked if necessary Repack bearings using a high temperature automotive type wheel bearing grease produced by a reputable manufacturer The soap type should be polyurea lithium complex or equivalent Use a NLGI Grade 2 product with a minimum dropping point of 440F Super Lube If the Recreational Vehicle is equipped with Super Lube there is no need to lift
52. ane Both the flame and the igniters in the burners of these appliances are sources of ignition and could cause an explosion These appliances must be turned OFF before entering a fuel filling station or refueling equipment Turning off the propane main tank valve only is not sufficient The appliances must be OFF at their electrical operating switches 78 7 Secure the vehicle with tie downs The attachment points you select on your equipment must be strong enough to support the weight of the equipment Usually attachment points that are low and centered on the equipment frame will be good An attachment to a decorative piece of chrome or plastic will usually not be a good tie down point Consider any leverage action that may occur An attachment point past the center of the equipment could cause the equipment to either swing around or flip over causing damage to the equipment or personal injury If you have any doubt about the attachment point you have selected stop and find a better attachment point Secure The Load Install blocking devices in the front back and on both sides of the wheels to keep it from rolling This block is strictly an additional safety precaution and does not reduce the need for strapping the vehicle in securely Use a minimum of three tiedowns to secure the vehicle to the trailer Use on tie down to secure the front of the vehicle to the trailer Use two tiedowns to secure the rear of the vehi
53. ansport any motor fuel inside the trailer Ventilate the interior of the trailer to reduce the risk of fire explosion or asphyxiation Open the ventilation panels on either side of the cargo area Do not operate propane appliances pilot lights or electrical equipment when motorized vehicles or motorized equipment are inside the trailer Set the cargo electrical disconnect switch to OFF 79 Chapter 11 Ramp Trailers Fuel soaked rags or other materials contain flammable and or explosive fuel vapors and other hazardous substances Clean up materials should be temporarily stored in a nonflammable vapor tight container until proper disposal facilities are available Do not store flammable clean up rags or materials inside the trailer inside any other vehicle or near any source of flame or ignition 80 Never jam or otherwise try to lock the refueling latch on the nozzle open Do not re enter your vehicle during refueling If you cannot avoid reentering your vehicle discharge any static build up before reaching for the nozzle by touching something metal with a bare hand such as the vehicle body or frame away from the nozzle In the unlikely event a static caused fire occurs when refueling leave the nozzle in the fill pipe and back away from the vehicle Turn off the fuel pump master switch immediately Do not over fill or top off your vehicle tank which can cause gasoline spilla
54. anty lasts or allow the exclusion of limitation of incidental or consequential damages so the above limitation or exclusions may not apply to you Some states do not allow the reduction in the statute of limitations so they may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Warranty Exclusions This Limited Warranty Shall Not Apply To Equipment products components appliances or accessories not manufac tured by Redwood whether or not warranted including but not limited to tires batteries generators washer dryer electronics and other installed equipment or accessories Trailers used for business rental commercial or disaster relief purposes or any purpose other than residential or recreational travel and family camping Trailers which are not originally sold through an authorized Redwood dealer and those sold through auction repossession salvage or an otherwise damaged or distressed condition Damage or loss caused in whole or in part by the acts or omissions of any kind by any party other than Redwood Damage or loss caused in whole or in part by the misuse abuse neglect theft vandalism product modification improper customer or dealer installa tion improper stowing of equipment incorrect line voltage unauthorized repair or failure to follow instructions supplied with the recreational vehicle Routine maintenance in
55. arge parking lots In time traveling with a recreational vehicle in tow will be as easy as driving the family car Controlling Sway or Fishtailing Sway or fishtailing is the sideways action of a trailer caused by external forces It is common for travel trailers to sway in response to strong winds or crosswinds or when passed by or passing a semi tractor and trailer or driving downhill Sway or fishtailing of your recreational vehicle can be controlled and is primarily impacted by four factors e Equipment e Tongue weight e Driving e Corrective measures Equipment When hitched together the trailer and the tow vehicle must be level The tires of both the trailer and tow vehicle should be in good condition and inflated to the pressure recommended as noted on the exterior of the trailer and in the owner s manual of the trailer and tow vehicle Your trailer brakes should work in synchronization with your tow vehicle brakes Never use your tow vehicle or trailer brakes alone to stop the combined load Your brake controller must be set up according to the manufacturer s specifications to ensure proper synchronization between the tow vehicle and the trailer Additionally you may have to make small adjustments occasionally to accommodate changing loads and driving conditions Also we recommend a friction sway damper or hitch with built in sway control be provided for your unit Please consult your dealer regarding this equipment as th
56. ates a potentially hazardous situation that if not avoided may result in property damage Important information regarding the maintenance of your recreational vehicle Terms and Symbols Used Optional This denotes items that may be an option on all or particular models Additionally some optional items can only be included during the manufacturing phase and cannot be added at a later date The inclusion of optional items does not imply or suggest the availability application suitability or inclusion for any specific unit Reporting Safety Defects If you believe that your vehicle has a defect which could cause a Crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying Redwood If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Redwood To contact NHTSA you may either call the Vehicle Safety Hotline toll free at 1 888 327 4236 TTY 1 800 424 9153 go to http www safercar gov or write to Administrator NHTSA 1200 New Jersey Avenue S E Washington DC 20590 You can also obtain other information about motor vehicle safety from http www safercar gov Table of Contents Introduction 1 Warranty 1 Danger
57. ating the slide room assure there are no objects or people in the path of the room or the Slidetopper 22 Awning Slide Out Optional When installed the A amp E Slidetopper awning will automatically open and close along with the slide room Fully extended the awning is level which may cause water to puddle on top of the canopy As the slide room is closed the awning will roll up and cause any puddles to spill over the sides of the awning Before retracting the slide room check to make sure the Slide Topper is free of any debris leaves twigs etc which can damage the awning or slide room components Cable Hook Up At many commercial campgrounds cable access is provided To utilize the cable access locate the exterior hookup on the side of the recreational vehicle Attach cable to access hook up and trailer hook up Finally make sure the antenna power booster is off Converter See Electrical Section Fan Tastic Vent Optional The Fan Tastic Vent runs on 12V Dependent upon the model operational control may be by a thermostat like control switch or by controls directly mounted on the vent See the information included in the unit packet for operating instructions concerning the installed model When using the Fan Tastic Vent close all vents and slightly open the windows on a shaded side of the coach The direction of the airflow is determined by which window s are opened Please no
58. ation or blowout and flat tires These actions along with other care and maintenance activities can also Improve vehicle handling Help protect you and others from avoidable breakdowns and accidents Improve fuel economy Increase the life of your tires Use this information to make tire safety a regular part of your vehicle maintenance routine Recognize that the time you spend is minimal compared with the inconvenience and safety consequences of a flat tire or other tire failure Safety First Basic Tire Maintenance Properly maintained tires improve the steering stopping traction and load carrying capability of your vehicle Under inflated tires and overloaded vehicles are a major cause of tire failure Therefore as mentioned above to avoid flat tires and other types of tire failure you should maintain proper tire pressure observe tire and vehicle load limits avoid road hazards and regularly inspect your tires Finding Your Vehicle s Recommended Tire Pressure and Load Limits Tire information placards and vehicle certification labels contain information on tires and load limits These labels indicate the vehicle manufacturer s information including Recommended tire size Recommended tire inflation pressure Vehicle capacity weight VCW the maximum occupant and cargo weight a vehicle is designed to carry Front and rear gross axle weight ratings GAWR the maximum weight the axle systems are designed
59. ave to go over a pothole or other object in the road Do not run over curbs or other foreign objects in the roadway and try not to strike the curb when parking Tire Safety Checklist Check tire pressure regularly including the spare at least once a month and before going on any trip Inspect tires for uneven wear patterns on the tread cracks foreign objects or other signs of wear or trauma Remove bits of glass and foreign objects wedged in the tread Make sure your tire valves have valve caps Do not overload your vehicle Check the Tire Information and Loading Placard or User s Manual for the maximum recommended load for the vehicle STEPS FOR DETERMINING CORRECT LOAD LIMIT 1 Locate the statement The weight of cargo should never exceed XXX Ibs on your vehicles placard 2 The figure stated on the placard is the available amount of cargo load capacity The weight of all cargo loaded in the vehicle may not safely exceed this figure 3 Determine the combined weight of cargo being loaded in the vehicle That weight may not safely exceed the available cargo Capacity For further information about wheel and tire safety 1 888 327 4236 TTY 1 800 424 9153 http www safercar gov and NHTSA 1200 New Jersey Avenue S E Washington DC 20590 Chapter 11 Ramp Trailers Ramp Trailer Weight Distribution All loaded trailers must remain within GVWR and GAWR limits Proper load distribution is especially i
60. by the tow vehicle s 12 Volt system The water pump certain lights power vents and other appliances are powered by the 12 Volt system The heart of the 12 Volt system is the battery Batteries are essentially storage devices for electrical energy Most batteries used in RVs are RV Marine Deep Cycle Lead Acid types These batteries contain lead plates and liquid sulfuric acid electrolytes in sections called cells Electrolytes are lost whenever a battery discharges energy or is recharged The level of the electrolyte must stay above the plate in each cell Many premature battery failures occur because the electrolyte level was not maintained For maintenance and storage information see the Care and Maintenance Section Chapter 3 Appliances and Equipment If the alarm sounds provide ventilation by opening windows and doors The CO build up may dissipate before help arrives but may be only temporarily solved It is crucial that the source of the CO is determined and repaired The CO alarm can only warn you in the presence of CO It does not prevent CO from occurring nor can it solve an existing CO problem Carbon monoxide can be fatal When the device detects carbon monoxide in the air it will sound Consult the individual detector s user manual for specific instructions and or audible warning meanings 29 Chapter 4 Electrical System Before plugging in the RV shore cord turn off all electric
61. ch to 20 30 ft Ibs 3 Begin with the appropriate bolt for your wheel 12 o clock position for 8 and 6 hole wheels and 2 o clock position for 5 hole wheels as illustrated and apply torque to all lug nuts following the star pattern indicated on the previous page 4 Stage 2 Increase your torque wrench setting to 55 60 ft Ibs 5 Begin with the appropriate bolt for your wheel and apply torque to all lug nuts following the star pattern indicated in Figure H 6 Following stage 2 the wheel can support the weight of the trailer and can be lowered off of the jack stands ie Stage 3 Increase your torque wrench setting to 110 120 ft lbs 8 Begin with the appropriate bolt for your wheel as illustrated and apply torque to all lug nuts following the star pattern indicated on the previous page Step 2 Follow Up Retorque after 10 25 and 50 miles ie After the first 10 miles of your trip pull your recreation vehicle off the road into a safe work area 3 Stage Installation 2 Set your torque wrench to 110 120 ft lbs 20 30 fv lbs 3 Begin with the appropriate 0 60 fullbs bolt for a wheel and apply torque F 55 40 foba o all lug nuts following the 90 100 fells star pattern indicated in Figure H 4 Reapply torque and 110 120 folbs repeat steps 1 2 amp 3 again at 25 40 150 fu lbs miles and at 50 miles of your first trip 5 The follow up process is complete and you should refer to the general lug nut torque mainten
62. cle to the trailer Four tiedowns one at each corner are preferred Attach tiedown hooks to the vehicles frame not to an accessory such as a mirror handle bar pedal etc Hooks on the other end must be attached to vehicle cargo anchors installed in the trailer For transport motorized cargo with manual transmissions should be left in first gear Vehicles with automatic transmissions should be in the park position The vehicle s ignition key should be turned off and removed the parking brake set the run stop switch in the stop or off position and the fuel lever turned to the off position The Safest Way To Unload Your Motorized Cargo The safest method of unloading is to push the vehicle down the ramp carefully braking to ensure control of the vehicle If you loaded your vehicle forward front in that means you will unload it in reverse Driving a motorized vehicle backwards down a hill the ramp is not recommended A slight turn of the handle or slip of a wheel can cause your vehicle to fall tip or roll sideways If you are on or in the vehicle you can be injured or killed Unload the vehicle safely as follows 1 Be sure the back tires of the vehicle are aligned with the ramp and there are no people pets or obstructions in the unloading area at the end of the ramp Assure that the ground surface will support the vehicle and that the vehicle cannot roll away uncontrolled 2 Stand at the front of the vehicle 3
63. cluding without limitation caulking re caulking and waxing of the body of the recreational vehicle tightening screws brake squeak lock up adjustment latches locks combustion systems changing fuses or light bulbs and maintaining the air conditioning and heating systems Adjustments to all doors drawers locks latches awnings and window treatments beyond 90 days after retail sale Damage or loss caused in whole or in part by the unauthorized attachments modifications or alterations to the structure body pin box or frame of the recreational vehicle including but not limited to trailer hitches for towing or platforms for supporting cargo Any upholstery damage including but not limited to tears punctures or misuse Any fading or die lot changes of fabrics or carpet Cosmetic issues with the Alpha ply roof material or its installation Damage or loss caused in whole or in part by exposure to natural or atmospheric elements corrosive chemicals ash or fumes generated or released by vehicles collision road hazards rock chips condensation or any other source Damage or loss caused in whole or in part by any animals including such things as rodents and or insects Damage or loss caused in whole or in part by the overloading or the improper balancing of the load Damage or loss caused in whole or in part by the willful or negligent acts of the driver of the vehicle pulling the recreational vehicle an acci
64. ctrical maintenance is also essential to the smooth operation of the slide out system Full battery current and voltage is essential for optimum performance Regularly check the terminals of the battery the control switch and the pump motor Look for signs of any corrosion or loose or damaged terminals and connections from environmental conditions as well as road debris and vibration Manual Crank Option The Lippert Electric Slide Out System comes with a manual override system This option can be utilized in case of power interruption or system failure Detailed instructions on using this option can be found in the manual for this slide out system Chapter 8 Care and Maintenance The instructions and recommendations located within this manual and the accompanying manufacturer s component literature should be read as failure to perform necessary or preventative maintenance may limit or void all or part of a specific warranty Care and maintenance of the recreational vehicle is an important step in maintaining the safety dependability and the appearance both interior and exterior of the unit Keep good records of all maintenance performed as these may be necessary for warranty information or may assist in possible repairs needed Operational usage and climates may affect the frequency of maintenance needed on certain components Preventative maintenance is important to the life and enjoyment of any recreational vehicle as many prob
65. ctricity can be caused by re entering a vehicle during fueling particularly in cool or cold and dry weather If you return to the fuel fill pipe during refueling the static may discharge at the fill point causing a flash fire or small sustained fire with gasoline refueling vapors If you cannot avoid getting back into the vehicle always first touch a metal part of the vehicle with a bare hand such as the door or some other metal surface away from the fill point upon exiting the vehicle Here are some additional refueling safety guidelines when refueling your vehicle or filling up gasoline storage containers Turn off vehicle engines Disable or turn off any auxiliary sources of ignition the trailer furnace water heater cooking unit and any pilot lights Turn off main propane valve Do not smoke light matches or lighters while operating the refueling system or when using gasoline anywhere else Use only the refueling latch provided on the gasoline dispenser nozzle Any Chapter 11 Ramp Trailers motorized equipment powered with flammable liquid can cause fire and explosion or asphyxiation if stored or transported inside the trailer To reduce the risk of fire explosion or asphyxiation Ue Do not allow passengers to ride inside the storage area at any time Prior to storing vehicles in the trailer run fuel out of the engine after shutting off fuel at the vehicle fuel tank Do not store or tr
66. d frame handle bar axle bolt etc 6 Remove the fuel hose and nozzle from its compartment An automatic bypass valve prevents pressure buildup when the pump is on with the nozzle closed 7 Place the nozzle into the equipment fuel filler and squeeze the handle to allow fuel to flow Be careful not to overflow the equipment fuel tank Wipe up any spilled fuel 8 When finished release the nozzle handle return the nozzle to its compartment 9 Lock the fuel transfer nozzle compartment to prevent unauthorized use The nozzle compartment must be locked at all times when not dispensing fuel 10 When you are finished with all the fueling turn off the pump master switch All parts of the fuel transfer system including bud not limited to the hoses pump nozzle fittings and tank have been selected for their quality safety and intended application Any alteration or replacement of any part by other than Redwood parts could jeopardize the integrity of the system and may result in serious injury or even death If your fueling system is not working properly or you need additional information on the use of your system contact your authorized Redwood dealer immediately or call Redwood directly Portable Containers When dispensing gasoline into a container use only approved portable containers and place it on the ground to avoid a possible static electricity ignition roe of fuel vapors Never fill a container er while the container is
67. dent involving the recreational vehicle the condition of any road surface over which the recreational vehicle is pulled or the striking or driving over a curb or any other object Damage or loss to the recreational vehicle caused in whole or in part by the tow vehicle selected by the owner to pull the recreational vehicle including but not limited to the improper selection or installation of towing hitch on tow vehicle weight distribution or equalizer equipment Any injury loss or damage beyond warranty repairs due to mold or fungi Damage or loss caused in whole or in part by the owner s operation use or misuse of the tow vehicle Any and all damage or loss to the owner s tow vehicle Rust or broken glass damage Wheel or axle alignment Re design or Re construction Damage to electronics due to voltage issues are not covered under warranty Representations made by any person including your dealer beyond those stated in this Limited Warranty Any trailer licensed registered or primarily used outside the USA or Canada Damage or loss caused by failure to seek and obtain repairs in a timely manner and Any incidental and consequential damages including but not limited to transportation fuel food lodging telephone calls towing charges bus and taxi fares or car rentals on site service calls as well as commercial use and loss of use Further any performance of repairs after the warranty coverage period
68. distance to stop Weather and road conditions will require adjustments to speed Anticipate dips gutters and depressions in the road slowing down well in advance these are the hardest jolts of any kind on your vehicle hitch recreational vehicle and items stored inside the unit Take dips and bumps slowly and be certain the trailer wheels have passed the point before accelerating Backing Back with care Having a person outside to assist is a good idea If no one is available to help the driver should inspect the area behind the vehicle to avoid any unseen obstacles and unpleasant surprises Braking Start sooner and lead with your trailer brakes Prior to beginning any trip make sure the brake control is adjusted See your accompanying literature for the brake control you had purchased for your tow vehicle Passing and Accelerating Remember when you pass another vehicle that it takes longer to accelerate and additional time must be allowed due to the added length of the trailer Passing should be done on level terrain and downshift if necessary for added acceleration Whenever deciding to pass another vehicle exercise caution and always use the turn signals Sharply Winding and Narrow Roads Keep well to the center of the lane equally away from both the center line and pavement edge This allows the trailer to clear the edge of the pavement without the likelihood of the wheels dropping onto the shoulder causing potential dange
69. e The inspection and service certification form can be found at the front of this manual and must be submitted to Redwood Service department within 30 days of the retail anniver sary date Warranty Disclaimers This warranty is expressly in lieu of all other warranties express or implied including any implied warranty of merchantability or fitness for any particular purpose and in lieu of all other obligations or liabilities on the part of Redwood Implied warranties including implied warranty of merchantability or fitness for a particular purpose if any given by law shall be limited to and not extend beyond the duration of the written limited warranty period No person has the authority to enlarge amend or modify this limited warranty Redwood will not be responsible or liable for loss of use of the recreational vehicle on site service calls or service charges loss of time inconvenience expenses for gasoline towing charges or transportation costs rental of substitute equipment telephone travel lodging damage or loss to personal property loss of revenues or other commercial loss or any other special or consequential damages of any kind or nature resulting from any defect in the recreational vehicle Any action to enforce this limited warranty or any implied warranty shall not be brought more than one 1 year after expiration of the term of this limited warranty Some states do not allow limitations of how long an implied warr
70. e RV manufacturer does not provide sway control devices Tongue weight The tongue weight should be between 10 to 15 of the total travel trailer weight See page 18 of this manual regarding the proper weight distribution of your recreation vehicle Driving This is the most important component The tendency for the vehicle to sway increases with speed therefore obey all speed limits and reduce during inclement weather or windy conditions Corrective measures If sway occurs the following techniques should be used 1 Slow down immediately remove your foot from the accelerator Avoid using the tow vehicle brakes unless there is a danger of collision Reduce speed gradually whenever possible If you can do so safely use the brake hand controller independent of the tow vehicle brakes to gently and progressively apply the trailer brakes This will help to keep the vehicles aligned Practice using the brake hand controller on a deserted parking lot Don t wait until an emergency occurs before using it Location of the brake hand controller is important and should be made easily accessible 2 Steer as little as possible while maintaining control of the vehicle Because of natural reaction lag time quick steering movements to counter trailer sway will actually cause increased sway and loss of control Keep both hands on the wheel Hold the wheel as straight as possible until stability is regained 3 Do not jam on the brakes or at
71. e but not both PULL THROUGH SITES Camp sites that you can pull your recreational vehicle through eliminating the need to back in RADIAL PLY TIRE A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the center line of the tread Appendix 89 Appendix 90 RECOMMENDED TIRE INFLATION PRESSURE This is the inflation pressure provided by the vehicle manufacturer on the Tire Information label and on the Certification VIN tag REINFORCED TIRE A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire RIM A metal support for a tire or a tire and tube assembly upon which the tire beads are seated RIM DIAMETER This means the nominal diameter of the bead seat RIM SIZE DESIGN This means the rim diameter and width RIM TYPE DESIGNATION This means the industry of manufacturer s designation for a rim by style or code RIM WIDTH This means the nominal distance between rim flanges ROADSIDE Refers to the side of the unit that faces the road when parked Also commonly referred to as Off DOOR SIDE RV Short for Recreational Vehicle RVIA Recreational Vehicle Industry Association SECTION WIDTH The linear distance between the exteriors of the sidewalls of an inflated tire excluding elevations due to labeling decoration or protective bands SHORE LINE The electrical cord that connect
72. e problem Fifth Wheel Coupler Inspect monthly or prior to each trip The hitch plate and locking mechanism should be generously lubed with a high temperature rated grease at all times Consult the paper work that accompanied the hitch purchase for manufacturer recommendations Safety Chains Safety chains should be inspected monthly If chains are damaged or weakened replace immediately Never tow without use of the safety chains Carefully read the component manufacturer s manual and any safety instructions provided in the unit packet prior to performing any maintenance Jacks e Tongue Jacks Manual travel trailers Whenever preparing to travel inspect the jack for any damage and test operation If jack is difficult to operate clean and oil lightly If jack is still difficult to operate or freezes call your dealer Service on any jack should be performed by qualified service personnel only e Tongue Jacks Power travel trailers Prior to traveling inspect the jack for any damage and test operation Check connections at battery and keep contacts clean and secure If the power jack malfunctions at any time call a local dealer Service on all power jacks should be performed by trained service personnel e Fifth Wheel Jacks Prior to each use inspect drop tube and inner ram tube Replace or repair as required per component manufacturer instructions Follow all preventative maintenance instructions provided
73. e roof material can however be cut by sharp objects Use caution when walking on or loading articles on the roof Care is needed when driving or parking to avoid punctures If damage does occur the roof may be patched with a special kit available through your dealer If accessories or new equipment is added be sure the installer is qualified to work on the rubber roof material Maintenance Inspect the roof at least every 90 days paying particular attention to the seams where the areas of sheet metal moldings rubber and or fiberglass are joined Carefully inspect the sealant around any vents skylights air conditioners etc Exposure to the elements will cause sealants to deteriorate over time Variations in climate and weather may accelerate deterioration Inspection and periodic resealing is essential as preventative maintenance If cracks or shrinkage is noticed immediately follow the rubber roof manufacturer s recommendations for repair or resealing Special sealants are used due Chapter 8 Care amp Maintenance 47 Chapter 8 Care amp Maintenance The rubber roofing material when wet may be slippery Always use caution when working on top of the RV 48 to the composition of the roofing material For the appropriate sealant please see your dealer Cleaning Prior to cleaning the roof rinse the roof off to remove any debris Be sure to keep the sidewalls wet to reduce streaking Standard
74. e tire materials This could result in sudden tire failure An under inflated tire will also cause poor vehicle handling rapid and or irregular tire wear and an increased in rolling resistance which results in decreased tow vehicle fuel economy The maximum cold inflation pressure for your tires is stated on the tire sidewalls and Federal certification label Keep your tires inflated to this maximum cold pressure This reduces the chance of a failure and improves towing stability Maintaining correct tire pressure for your trailer is of the utmost importance and must be a part of regular vehicle maintenance You must weigh your trailer when fully loaded as you expect to use it You need to weigh all axles together and calculate the hitch weight You may find that even though the total weight is within the GVWR one side may be overloaded For this reason you must know the weight on each side of the trailer When you know the weight on each side of the trailer the combined axle assembly and the hitch weight you will be able to manage your loading to be able to maintain good balance and assure good and safe handling on the road There are some tips to help plan your loading Do not overload Experiment with various loads starting with light loads and working up to heavier loads Take into consideration the load of the fresh water system The tow vehicle and the terrain will affect the true weight you should carry Distribute the lo
75. e vehicles are present Occupants shall not sleep in the vehicle storage area while vehicles are present gt Chapter 11 Ramp Trailers The rear cargo door weighs approximately 200 pounds It is designed for two person operation The maximum cargo capacity of the rear cargo door ramp is 2000 pounds When the trailer is unhooked from the tow vehicle lower and check the stabilizing jacks before using the loading ramp Failure to do so could cause the trailer to tip back as the load is shifted to the rear of the cargo area causing property damage personal injury and or death Hitch the trailer to a two vehicles before loading and unloading the rear cargo area It is not safe for persons or pets to occupy the vehicle storage area while vehicles are present Failure to follow these important precautions may result in serious injury or death Chapter 11 Ramp Trailers There is a hazard of serious personal injury when using a loading ramp Never ride motorized cargo up a loading ramp It the motorized cargo loses traction and spins sideways it may slip sideways off the ramp tipping sideways and possibly falling on the rider causing injury CARBON MONOXIDE GAS CAN KILL YOU Fuel burning devices such as ATVs or motorcycles that burn gasoline diesel or other fuels produce carbon monoxide when they are operating Carbon monoxide gas is invisible odorless and colorless Dangerou
76. eck the panel reading when the fresh water tank is filled 2 Material trapped on the sides of the holding tanks also may provide full readings when the tank is actually empty Use of a spray to wash out the tank following dumping should help prevent this condition 3 Grease build up on the sensor probes may indicate false readings or no readings at all Avoid pouring any grease oils or similar substances down drains or the toilet If this occurs wash the tank s out with soapy water Winterization RV components can be damaged from the effects of freezing Protection of the plumbing system and related components is crucial Damages due to weather are not covered under warranty at any time Many recreational vehicle owners choose to have their units winterized by their dealer while others choose to do it themselves Following are descriptions of two methods used to winterize Me Compressed Air Dry Method Uses compressed air to blow out any remaining water in the system after draining the system of all water This method requires an air compressor and appropriate adapters 2A RV Anti Freeze Wet Method without ez winterizing system 2 B RV Anti Freeze Wet Method with ez winterizing system Uses RV approved nontoxic potable anti freeze in the system and does not require any special tools Many Redwood products include an optional by pass kit that allows the plumbing system to bypass the hot water heater reducing the amount
77. eeze or having had an existing unit winterized before winter storage the plumbing system must be flushed and sanitized prior to use Do Not Attempt to turn on water heater if system is winterized Perform the following prior to attempting to operate the water heater or use the plumbing system 1 Drain all tanks fresh water and sewage 2 Attach garden hose to fresh water fill and fill tank 3 Turn on pump switch and open cold water side of all faucet shower fixtures Leave open until water runs clear Repeat for hot water side Flush toilet until clear water runs into bowl Dump tanks again Sanitize water system If a water filter is installed drain lines remove filter assembly clean and reinstall with new filter When ready to use the water heater turn by pass valve to open position to allow water to enter hot water heater tank and fill according to instructions PEO pe ma Waste Water System The wastewater system inside the recreational vehicle is self contained while on the road or set up in a campsite The main parts of the waste system are the toilet holding tanks and tank dump valves As in residential households the drainage system also includes p traps and roof vents to allow escape of odors and gases Toilet The toilet operates from water supplied either by the fresh water tank or from an exterior water supply connected at the city water hook up The water pump must be turned on when utilizing the water
78. ent 22 Fifth Wheel 1 11 13 18 23 34 37 49 50 86 87 Fireplace 23 Fresh Water 36 43 86 88 91 Furnace 4 22 23 26 46 60 62 78 79 Generator 9 11 24 28 85 87 Hitch 7 11 13 16 18 48 49 62 63 70 71 73 75 87 89 King Pin 89 Propane Detector 28 36 Microwave 25 Mold 7 8 21 47 60 61 88 Monitor Panel 25 36 37 39 40 No Fuss Flush 44 Power Cord 30 31 33 90 Refrigerator 27 28 30 46 84 Roof 9 14 19 28 30 42 47 48 54 62 85 89 Slide Out 18 22 44 46 Stabilizing Jacks 18 75 Toilet 40 44 56 86 Torque 4 13 14 50 53 Warranty 1 5 11 22 40 46 49 50 54 62 84 85 Waste Water 41 43 85 87 Water Heater 4 11 30 36 42 78 79 85 Water Pump 29 36 37 39 41 42 Winterization 39 42
79. er and inspecting it for leaves or other debris before closing After cleaning allow the fabric to dry completely before rolling up When raining lower one end of the awning so that the water will run off and not pool on the fabric and avoid rolling it up when wet If necessary unroll as soon as conditions permit to allow the awning to dry Chapter 3 Appliances and Equipment a NOTICE Redwood RV is not responsible for damages to the TV which occur during or related to the transport of this unit Other than removing the TV for transport the supplied straps are the best way to minimize the potential for damage Do not raise TV antenna near overhead electrical wires as contact may cause injury or death 21 Chapter 3 Appliances and Equipment a NOTICE If heavy rain or wind is predicted or whenever you leave the awning unattended it is best to close the awning Damage to the awning or unit due to weather is not covered under the Redwood RV Company Limited Warranty or the awning manufacturer warranty DO NOT attempt any repairs to the awning The awning roller tube is under extreme spring tension Repairs should only be performed by an authorized dealer repair center a NOTICE DO NOT USE the Slidetopper in snowing or freezing rain conditions as it may prevent the awning from retracting properly with the slide room and cause damage to the awning and or slide room Before oper
80. er can lead to the rollover of the trailer and tow vehicle resulting in serious injury or death Be sure to follow the instructions and warnings as outlined on page 16 Mold There are mold and mold spores throughout the indoor and outdoor environment There is no practical way to eliminate all mold and mold spores in the indoor environment the way to control indoor mold growth is to control moisture see page 12 Towing and Weight Distribution Weight distribution is an important factor when loading your fifth wheel and travel trailer or motorhome A recreational vehicle with the cargo distributed properly will result in efficient trouble free towing see page 18 Formaldehyde Formaldehyde is an important chemical used widely in building materials and numerous household products It is also a by product of combustion and certain other natural processes Thus it may be present inside the trailer with some individuals being sensitive to it Ventilation of the unit normally reduces the exposure to a comfortable level see page 62 Generator Safety Do not operate the generator in an enclosed building or in a partly enclosed area such as a garage Nor should the generator be operated while sleeping Be sure to follow all instructions and warnings in this manual and the manual provided by the generator manufacturer See page 27 Lug Nut Torquing Being sure wheel mounting nuts lug nuts on trailer wheels are tight and properly torq
81. er fill connection 9 Set the pressure no greater than 30 pounds and blow out the water lines until no water can be seen coming out of the fixtures and lines 10 Pour RV anti freeze into drains p traps toilet and tanks Method Pr A RV Anti Freeze without ez winterizing system With By Pass Kit Installed 1 Purchase 4 6 gallons of RV approved non toxic anti freeze 2 Drain all tanks fresh water and sewage tanks 3 Turn water heater by pass valve to by pass position The by pass valve is located near the water heater incoming lines an access panel may have to be removed depending upon the model 4 Drain water heater 5 If installed remove water filter from assembly and discard Install diverter if included 6 Pour an amount of RV non toxic anti freeze into the fresh water tank to fill the tank above minimum water pump operating level Use of a long funnel may be helpful Add more if necessary during procedure 7 Turn on pump switch and open the cold water side of all faucet fixtures Leave open until the anti freeze comes out generally pink in color Repeat for hot water side 8 Flush toilet until anti freeze begins to flow into the bowl and then pour one gallon of anti freeze down the toilet to winterize the black tank 9 Pour anti freeze down each shower tub lavatory sink and kitchen sink to fill p traps 10 To winterize gray tank s pour one gallon down each related sink drain Method
82. facturer s warranties on components included within your coach Reviewing and adhering to the information contained in this manual and all supplied component information is the responsibility of the owner It is the responsibility of the owner to return the recreational vehicle to an authorized dealer for any repairs and services that may be required Your Redwood dealer is responsible for proper service and maintenance before delivery and will have a continued interest in your satisfaction Therefore we strongly recommend that warranty and maintenance services be performed by your Redwood dealer Yearly inspections are required to qualify for the five year structural warranty and it is the owner s responsibility to submit the proper documentation to Redwood RV Failure to do so will result in cancellation of the five year structural warranty The inspection certification form can be found in the front of this manual Furthermore the owner is responsible for any costs incurred in the performance of the inspection Dealer s Responsibilities The dealer is responsible for acquainting the owner with the operation of all systems and components installed in the recreational vehicle as well as explaining the provisions of the Limited Warranty The customer s selling dealer is required to perform all warranty repairs during the limited warranty period The dealer should instruct the customer on how to receive out of town service whether the re
83. for said product In no way shall Redwood s Limited Warranty be modified or amended by Redwood providing the service for the appliance or component This warranty gives you specific legal rights and you may also have other rights which vary from state to state Inspection To assist you in avoiding problems Redwood RV requires each dealer to review the limited warranty and inspect the unit with you The dealer has been provided with a pre delivery checklist that must be reviewed and approved by you Do not sign this checklist until the inspection is complete and all questions you may have are answered Unit Information Packet In addition to this Owner s Manual a unit information packet is located inside your new recreational vehicle Inside the packet are product manuals and information on systems and equipment in the coach Individual product warranty registrations accompany this information and should be completed and mailed promptly Some components in this manual or packet may be components of a differing product line and or optional equipment Inclusion of these informational manuals does not suggest that they are installed or available for a specific recreational vehicle Owner Registration As a convenience to you the owner registration form is completed by your dealership at the time of delivery After the owner signs this form the dealer will send the completed form to Redwood RV within 30 days Please make sure this form i
84. form in dead air spaces Allow air to circulate inside closets and cabinets leave doors partially open Please keep in mind that a closed cabinet full of stored goods prevents circulation and allows the exterior temperature to cause condensation e The natural tendency would be to close the vehicle tightly during cold weather This will actually compound the problem Simply put you need to remove some of the warm air and allow some cool outside air to get inside the vehicle so the furnace will not recycle the humid interior air About Molds What are molds Molds are microscopic organisms that naturally occur in virtually every environment indoors and out Outdoors mold growth is important in the decomposition of plants Indoors mold growth is unfavorable Left unchecked molds break down natural materials such as wood products and fabrics According to the Center for Disease Control exposure to damp and moldy environments may cause a variety of health effects or none at all Some people are sensitive to molds For these people molds can cause nasal stuffiness throat irritation coughing or wheezing eye irritation or in some cases skin irritation People with mold allergies may have more severe reactions Immune compromised people and those with chronic lung illnesses such as obstructive lung disease may get serious infections in their lungs when they are exposed to mold What factors contribute to mold growth For mold g
85. g the fresh water tank the water is pumped through the water lines by means of the water pump When utilizing an exterior source such as a campsite water supply the pump is not needed as the water is already pressurized and will flow through the water supply lines within the trailer Water Pump The 12 Volt water pump installed is self priming and totally automatic operating upon demand When a fixture is opened the pump draws water from the tank and pressurizes the lines providing water to the open fixture The pump has an on off switch and is located on the monitor panel DO NOT turn on the pump if the fresh water tank is empty Before Turning On The Pump Switch 1 Check the water level in the fresh water tank if empty refill See Fresh Water Tank Fil 2 Open kitchen and bathroom faucets hot and cold valves and any shower tub fixtures 3 Check to make sure Water Heater By Pass Valve is set to Normal Flow to allow water into the hot water heater 4 Turn on switch for water pump and allow the pump to fill the water lines and hot water heater tank 5 Close each faucet after it delivers a steady stream of water 6 The water pump should stop running after all faucets are closed 7 Pump should now run on demand when a faucet is opened and stop when the faucet is closed Fresh Water Tank A fresh water tank is equipped on all travel trailers and fifth wheels Tanks vary in size according to produc
86. gas appliances Most Propane gas appliances are vented to the outside Gasoline fumes could enter the appliance and ignite from the burner flame causing an explosion or fire 2 Chapter 3 Appliances and Equipment 28 ANY SERVICE TO THE REFRIGERATOR MUST BE PERFORMED BY A QUALIFIED REPAIR TECHNICIAN Roof Vents Manual and or power roof vents are installed on Redwood Recreational Vehicles For Fan Tastic Vent see the information on this specific product in this section Operate the roof vents when showering bathing washing dishes or anytime hot water is used as it allows moisture to escape Ventilation is extremely important in reducing condensation formation Safety Fire safety is important whether at home or in a recreational vehicle The best way to limit fire risk is by prevention Follow the manufacturers instructions on the use of all appliances and observe all safety warnings and instructions included Before camping make certain the locations of all safety equipment inside the coach and all emergency exit windows as well as doors An escape plan for emergencies whether at home or camping is always a good idea Egress Windows Egress or Emergency Exit Windows are labeled from the factory with the word EXIT All Egress windows can be distinguished by red operational handles or levers Dependent upon the window type an egress window may be a large section or an entire window Review the
87. ge Never allow children under licensed driving age to operate the pump Avoid prolonged breathing of gasoline vapors Use gasoline only in open areas that get plenty of fresh air Keep your face away from the nozzle or container opening Never siphon gasoline by mouth Never put gasoline in our mouth for any reason Gasoline can be harmful or fatal if swallowed If someone swallows gasoline do not induce vomiting Contact an emergency medical service provider immediately Keep gasoline away from your eyes and skin it may cause irritation Remove gasoline soaked clothing immediately Use gasoline as a motor fuel only Never use gasoline to wash your hands or as a cleaning solvent Fuel Transfer System Operation To operate the fuel transfer system also see the Fuel Pump Owner s Manual in your Owners Information Package 1 Lower the tongue jack or 5th wheel jacks to the ground This will electrostatically ground the trailer to reduce the possibility ot static discharge while refueling 2 Set the cargo area disconnect switch to ON 3 Close the vents in the side of the trailer to prevent fuel vapor from entering the trailer 4 Press the fuel transfer pump master timer switch to ON Each press of the switch allows the pump to run for 5 minutes When the pump stops press again in necessary for another 5 minute run 5 Attach the ground clip securely to a bare metal part of the equipment to be fuele
88. heels hitch or pin and total weight How Overloading Affects Your RV and Tires The results of overloading can have serious consequences for vehicle safety Too much weight on your vehicle s suspension system can cause spring shock absorber or brake failure handling or steering problems irregular tire wear tire failure or other damage An overloaded vehicle is hard to drive and hard to stop In cases of serious overloading brakes can fail completely particularly on steep hills The load a tire will carry safely is a combination of the size of tire its load range and corresponding inflation pressure Excessive loads and or under inflation cause tire overloading and as a result abnormal tire flexing occurs This situation can generate an excessive amount of heat within the tire Excessive heat may lead to tire failure It is the air pressure that enables a tire to support the load so proper inflation is critical Since RVs can be configured and loaded in many ways air pressures must be determined from actual loads determined by weighing and taken from the load and inflation tables provided by the tire manufacturer These air pressures may differ from those found on the certification label However they should never exceed the tire limitation for load or air pressure If you discover that your tires cannot support the actual weights the load will need to be lightened Tire Safety Tips Preventing Tire Damage Slow down if you h
89. hermostat Set the temperature select lever to the desired temperature level Set the system switch to FURNACE Cooling Operation A C and Heat Thermostat _ Set the temperature select lever to the desired temperature level Select the FAN speed HI Maximum cooling dehumidification LO Maintaining temperature level night use Select FAN AUTO ON switch AUTO Runs whenever cooling required and stops when not required ON Air conditioner fan runs continuously to circulate air Set the system switch to the COOL position When the SYSTEM switch is in the OFF or FURNACE and the AUTO ON 10 Switch is in the ON position the A C fan will run continuously at the selected fan speed This circulates air inside the RV Ot ae el oO Fireplace Fireplaces run on standard 120V and have full electrical certification throughout North America If you choose to activate the heat feature the fireplace will provide up to 5 115 BTU s Flame brightness is adjustable and the choice is yours whether or not to use the heat feature Built in safety features include impact resistant safety glass cool glass upon touch and a safety switch for overheating with user reset Read all documentation included prior to using Chapter 3 Appliances and Equipment Failure to read the furnace user s information manual and follow instructions could cause a fire or explos
90. home in a warmer location such as a garage so that the battery condition can be monitored and charged as needed during storage periods Appliances See Chapter 3 Bedspreads Refer to the label attached to the bed spread by the manufacturer Care instructions should be given In most instances or whenever in doubt dry clean all fabric products such as drapes and bedspreads for best appearance and prolonged life Washing draperies and bedspreads in washers will cause premature deterioration fading shrinkage and or possible damage Blinds and Shades Venetian blinds and day night shades should be vacuumed regularly with a soft brush attachment Use of a soft cloth and mild cleaner on blinds will help keep them new looking For fabric shades upholstery cleaners are not recommended Instead spot clean when necessary using a mild soap and water solution on area Cabinet Doors and Drawers Wood The cabinet doors and drawer fronts are solid wood and should be cared for similar to the fine furniture in your home Using a quality furniture polish will help maintain the beauty and luster of the wood as well as keep the wood from drying out The accidental scratches can be covered satisfactory with a good quality commercial furniture scratch remover Carpeting The carpeting installed is made of nylon and is easy to maintain Vacuum regularly to remove abrasive grit Water based spills and spots should be removed immediately with
91. iagrams below This tag contains the GVWR GAWR front and rear and tire pressure limits Chapter 2 Towing and Leveling Kitchen Cabinet RVIA Weight Label Location The RVIA Weight Label is located on the inside of an upper kitchen cabinet door In general the tag is affixed to the cabinet above or adjacent to the sink This tag provides the GVWR rating the UVW Unloaded Vehicle Weight and the computation for CCC Cargo Carrying Wheel Separation Can Occur Capacity Exceeding the GVWR and GAWR ratings for your unit could result in serious damage to the suspension frame or other components e i E i _ n ll Ly Weighing Your Unit Fifth Wheel e Pull forward on the scales until only the coach s axles are on the scale Record axle weight Pull off the scales and unhook from the fifth wheel Weigh the truck by itself and record this weight e To determine hitch pin weight subtract the weight of the tow vehicle from the combined truck coach weight Write this number down e To determine overall weight add the hitch weight plus axles Hitches and Towing Fifth Wheel 1 Adjust the landing gear jacks until coach is at level for hooking to the tow vehicle 2 Place wheel chocks behind fifth wheel s tires 3 Lower the tailgate on truck 4 Release the fifth wheel lock handle on the tow vehicle 5 Line up the tow vehicle so the fifth wheel will accept the kingpin 6 Close and latch tailgate
92. ime but they can lose air suddenly if you drive over a pothole or other object or if you strike the curb It is difficult to determine tire inflation pressure by looking at the tire Purchase a tire pressure gauge to keep in your vehicle Gauges can be purchased at tire dealerships auto supply stores and other retail outlets The recommended tire inflation pressure is the proper pressure when a tire is cold A cold tire is one that has not been driven on for at least three hours When you drive your tires get warmer causing the air pressure within them to increase Therefore to get an accurate tire pressure reading you must measure tire pressure when the tires are cold Refer to the tire sidewalls for the recommended tire pressure Your trailer may be equipped with optional tires Always refer to the tire sidewalls for recommended tire pressure Check and write down the pressure in all tires If the pressure is too high in any of the tires slowly release air by gently pressing on the tire valve stem with the edge of your tire gauge until you get to the correct pressure If the tire pressure is too low note the difference between the measured tire pressure and the correct tire pressure You will need to add air to get to the correct pressure Add air to each tire that is under inflated Check all the tires again to make sure they have the same air pressure If you have been towing your trailer and think that a tire is under
93. in damage to the coach and or serious injury or even death Before actuating the system please keep these things in mind 1 Parking locations should be clear of obstructions that may cause damage when the slideout room is actuated 2 Be suer all persons are clear of the coach prior to the slideout room actuation 3 Keep hands and other body parts away from slideout mechanisms during actuation Severe injury or death may result 4 To optimize slideout actuations park coach on solid and level ground Description The Lippert Hydraulic Slideout System is a rack amp pinion guide system utilizing a hydraulic actuator to move the room assembly The power unit drives the cyliner rod in a forward motion to drive the slideout room in and out The Lippert Hydraulic Slideout System is designed to operate as a negative ground system Prior to Operation Prior to operating the L ppert Hydraulic Slideout System follow these guidelines 1 Coach should be parked on the most level surface available 2 Leveling or stabilizing system should be actuated to ensure coach will not move during operation of Bed Lift System 3 Be sure battery is fully charged 4 Be sure to keep all persons and pets clear of Bed Lift System during operation System Maintenance The Lippert Hydraulic Slideout System has been static tested to over 4 000 continuous cycles with out any noticeable wear to rotating or sliding parts it is recommended that when
94. inflated fill it to the recommended cold inflation pressure Remember to recheck and adjust the pressure in all tires when you can obtain a cold reading Tire Tread Possible Cause Remedy Check amp Adjust Pressure When Cold Sue Cities Over Inflation Check amp Adjust Under Inflation Pressure When Cold Inside amp Outside Check amp Unload as Necessary and or Have Alignment Checked 1 Smooth Outside Wear One Loss of Camber or Over Loading Square Axles Feathering Across the Face Cupping Flat Spots Axle Not Square to Frame or Incorrect Toe In Loose Bearings or Wheel Balance Wheel Lock Up and or Have Alignment Checked Check Bearing Adjustment and Wheel amp Tire Balance Adjust Bakes Chapter 10 Tire Safety Information 65 Chapter 10 Tire Safety Information There is a danger of serious injury or death if a tire of one bead diameter is installed on a rim or wheel of a different rim diameter ALWAYS replace a tire with another tire of exactly the same bead diameter designation and suffix letters To avoid vibration or shaking of the vehicle when a tire rotates the tire should be properly balanced This balance is achieved by positioning weights on the wheel to counterbalance heavy spots on the wheel and tire assembly A wheel alignment adjusts the angles of the wheels so that they are positioned correctly relative to the vehicle s
95. ings Adapters These devices connect to the end of a 50 amp shore cord to allow it to plug into a 30 amp outlet or the end of a 30 amp shore cord to allow it to plug into a 15 amp outlet When using adapters your available electrical power for the entire unit is reduced to the rating of the adapter For Example if using a 30 to 15 amp adapter the entire unit only has 15 amps available for power This is not adequate to properly run an Air Conditioner or certain other appliances See chart on page 33 Extension Cords It may be necessary to use an extension cord to extend your recreational vehicle shore cord to the available campground electrical outlet It is critical the correct size cord is utilized ie 30 amp service 30 amp extension cord If using an extension cord rated less than the RV s shore cord it reduces the available electrical power for the entire unit to the rating of the extension cord The length of the extension cord can also affect the available power Do not use ANY adapters with an extension cord and do not plug multiple extension cords together at one time Your local Redwood dealer can assist you in obtaining the proper extension cord for your needs Converter The main purpose of the converter in your RV is to provide 12 Volt power to the unit while plugged into an AC outlet such as at a campground The converter will as its name indicates convert the incoming alternating current to direct current so as t
96. inside a vehicle a a car trunk the bed of a pickup truck or the floor of a trailer GenSet When fueling a portable container manually control the nozzle valve throughout the filling process Fill a portable container slowly to decrease the chance of static electricity buildup and minimize spilling Control Panel Configuration and control location differs depending on model Keep the fuel nozzle in contact with the rim of the container opening while refueling Fill container no more than 95 percent full to allow for expansion Place cap tightly on the container after filling do not use containers that do not seal properly Store gasoline only in approved containers Never store gasoline in glass or any other unapproved container If gasoline spills on the container clean up the spill immediately Fuel pump emergency gt shutoff switch located on frame rail The emergency shutoff switch will disconnect power to the fuel transfer system Chapter 11 Ramp Trailers Sidewall vent Squeeze handle and rotate to open close If a fuel spill occurs in the storage area of the trailer open the windows and sidewall vents and wipe up the fuel with cloth or paper towels Dispose of the towels in a suitable hazardous waste container Do not hose out the trailer with water Clean the fuel spill areas with a grease oil dissolving cleaner such as 409 Thoroughly
97. into the passenger compartment particularly those which can be down wind even part of the time 9 DO NOT operate the generator when parked in close proximity to vegetation snow buildings vehicles or any other object could deflect the exhaust under or into the vehicle 10 DO NOT touch the generator when running or immediately after shutting off Heat from the generator can cause burns Allow the generator to cool before attempting maintenance or service Microwave Convection Oven Optional Installed microwaves operate on 120V AC power only and are a popular for quick and convenient heating and cooking Due to differing models used it is recommended that the Owner s Guide in the Unit Packet be read to for use on special features and operations Care and Maintenance To clean exterior surface and the oven interior use only mild non abrasive soaps or detergents applied with a soft sponge or cloth Never operate the microwave when oven is empty Monitor Panel See Plumbing Section Range Hood The range hood operates on 12V power and should be used as a ventilating system when cooking Operational switches for the fan and or light are on the front panel of the range hood Care and Maintenance Care of the range hood is similar to the range Use warm soapy water and wipe off any grease before staining can occur Do not use harsh chemical cleaners or abrasives Clean the plastic light lens and filter by removing and
98. ion causing property damage serious injuries or loss of life 23 Chapter 3 Appliances and Equipment A generator produces carbon monoxide from exhaust fumes from its engine during operation Carbon monoxide can be fatal When the device detects carbon monoxide in the air it will sound Consult the individual detector s user manual for specific instructions and or audible warning meanings 24 Generator Optional Any service or maintenance recommended by the manufacturer should be performed at an authorized service center and in accordance with all generator manufacturer recommendations Please thoroughly read the accompanying manual IMPORTANT MAKE SURE TO READ AND UNDERSTAND THE GENERATOR OWNER S MANUAL BEFORE OPERATING THE GENERATOR Observe all operating instructions and warnings as well as all recommended maintenance schedules and procedures The onboard generator makes your RV fully self contained It allows you access to 120 volts when there is no shore power available but keep in mind that carbon monoxide is deadly NEVER sleep in the RV with the generator running Before you start and use the generator inspect the exhaust system Do not use it if the exhaust system is damaged Test the carbon monoxide detector every time you use the RV Know what the symptoms of carbon monoxide poisoning are Dizziness e Vomiting e Nausea Muscular twitching e Intense headache e Throbbing in the
99. k N Level and stabilize the trailer 3 Unlock the rear door loading ramp and carefully lower it to the ground 4 If equipped with a power bunk raise both bunks fully 5 Move things out of the way of your cargo whether you are loading or unloading Have any idea where your cargo will be positioned after your load unload activities 6 Use caution and proper lifting techniques when loading and unloading items from the cargo area 7 Use extreme caution when loading unloading ATV s motorcycles or other vehicles motorized cargo or vehicle s These machines are generally heavy and may be hot from operation and or covered with dirt oil or other substances that may make them slippery See the Special Procedures for Loading and Unloading Motorized Cargo for more details 8 Make certain that the door seals and hinge area are free of any debris such as sand or snow before closing the rear door loading ramp 9 Inspect the hinges assist spring and latch mechanism before reach trip for signs of wear or damage and make any needed repairs for safe operation and towing Loading and Unloading Motorized Cargo AN Any motorized vehicle or any motorized equipment powered with flammable liquid can cause fire explosion or asphyxiation if stored or transported within the recreational vehicle To reduce the risk of fire explosion or asphyxiation AN Passengers shall not ride in the vehicle storage area whil
100. k oof oh By Pass Kit The by pass kit is a popular convenience feature that allows for easier drainage of the hot water heater tank and winterization of the unit The by pass kit is installed near the cold water inlet of the water heater and allows for blockage of water flow into the water heater saving time and reducing the amount of anti freeze needed during winterization Monitor Panel The monitor panel allows you to check the approximate liquid levels in the fresh water and the gray and black holding tanks Dependent upon the type of monitor panel 3 or 4 tanks can be monitored along with the charge condition of the battery The water heater switch is located on some models Operation Depress the button for the desired reading tank or battery The levels readout for the tanks will read at Empty E 1 3 2 3 or Full F All lights will be lit when full The battery conditions are as follows C Charge G Good F Fair L Low Chapter 6 Plumbing System 39 Chapter 6 Plumbing System 40 Erroneous Readings The monitor panel displays readings from sensors attached to the tanks These sensors can send false readings when the following conditions occur 1 Water with low mineral content Minerals in water help conduct the electrical signal to the monitor display Some water which is very low in mineral content may not conduct the signal properly Although infrequent this condition can exist Ch
101. le of 49 CFR 571 110 OCCUPANT DISTRIBUTION The distribution of occupants in a vehicle as specified in the third column of Table of 49 CFR 571 110 OPEN SPLICE Any parting at any junction of tread sidewall or innerliner that extends to cord material OUTER DIAMETER The overall diameter of an inflated new tire OVERALL WIDTH The linear distance between the exteriors of the sidewalls of an inflated tire including elevations due to labeling decorations or protective bands or ribs PILOT Small flame that is used to ignite the main burner of a Propane fired appliance PIN WEIGHT The vertical trailer load supported by the king pin of a fifth wheel hitch PLY A layer of rubber coated parallel cords PLY SEPARATION A parting of rubber compound between adjacent plies PNEUMATIC TIRE A mechanical device made of rubber chemicals fabric and steel or other materials that when mounted on an automotive wheel provides the traction and contains the gas or fluid that sustains the load PRODUCTION OPTIONS WEIGHT The combined weight of those installed regular production options weighing over 2 3 kilograms 5 Ibs in excess of those standard items which they replace not previously considered in curb weight or accessory weight including heavy duty brakes ride levelers roof rack heavy duty battery and special trim PRIMITIVE CAMPSITE Campsite that offers limited connections May have city water or electrical availabl
102. lems can be caught before they occur Please do not hesitate to call your dealer with a question on the maintenance or care of any item The care and maintenance of appliances are discussed within the appliance chapter Always refer to the manufacturers recommendations located within the literature contained within the unit packet Exterior Fiberglass Gel Coat Finish Care of the Filon finish is similar to caring for a new car Any finish will deteriorate over time Exposure to extreme sunlight pollutants and excessive moisture can cause dulling fading and yellowing Regular washing and periodic waxing will help maintain the glossy new look When washing use a mild automotive or RV wash solution available at your dealer being sure to rinse off any loose debris first Avoid spraying water directly into the furnace and refrigerator vents Waxing the Filon areas twice a year is recommended Wax with an automotive wax or polish developed for boats Follow all directions by the wax manufacturer carefully and remember to wash and wax out of direct sunlight and when surfaces are cool Metal The aluminum exterior has a baked on enamel finish Washing frequently with an automotive or RV wash solution will help avoid staining from debris and soil build up Always rinse unit with clear water prior to washing to remove any loose dirt Waxing two to three times a year with a good automotive paste wax will help preserve the finish DO S
103. locations and operational instructions posted upon the window with all passengers Fire Extinguisher Each recreational vehicle includes a fire extinguisher which is located near the main entry door The fire extinguishers are rated for Class B gasoline grease and flammable liquids and Class C electrical fires Test and operate according to manufacturer instructions Propane Detector See the Propane section of this manual Smoke Detector For safety a smoke detector is installed in the living cooking area Smoke detectors should be tested prior and during each camping trip or weekly during the season Most detectors are powered by a 9 Volt battery Keeping fresh extra batteries on hand is a good idea Carbon Monoxide Detector A carbon monoxide CO detector is installed in your coach For specific information regarding the specific operation or functions of the particular detector in your unit consult the individual manufacturer s owner s manual Common sources of CO are malfunctioning or misuse of gas appliances vehicle engines generators and many other fuel burning products Indications of CO poisoning are but not limited to Mild Exposure Symptoms of the flu minus a fever Slight Headache Dizziness Fatigue Medium Exposure Sever Throbbing Headache Drowsiness Confusion Fast Heart Rate Extreme Exposure e Unconsciousness Convulsions Cardiorespiratory Failure e Death For your safe
104. low as possible and distribute evenly front to back and side to side Securing your possessions can prevent damage from shifting during towing and maintain the weight distribution balance achieved during preparation for travel You must not exceed the GVWR or GAWR of the unit see definitions To verify GVWR total the loaded hitch and axle weights If this total exceeds GVWR you must remove items until the vehicle weight is within this limit You can verify that the coach s axles are not overloaded by comparing the loaded axle weight with the GAWR If the reading is above this limit redistribute the item load Finally make sure the pin weight of the loaded fifth wheel falls within the limits of the tow vehicle Weight Ratings Definitions GVWR Gross Vehicle Weight Rating The maximum permissible weight of this coach when fully loaded It includes all weight at the unit s axle s and tongue or pin UVW Unloaded Vehicle Weight The weight of this fifth wheel as manufactured at the factory It includes all weight at the coach s axle s and tongue or pin If applicable it also includes full generator fluids fuel engine oil and coolants CCC Cargo Carrying Capacity Is equal to GVWR minus each of the following UVW full fresh potable water weight including water heater and full LP gas weight GAWR Gross Axle Weight Rating The maximum allowable weight that an axle system is designed to carry 11
105. low the recommendations contained in Chapter 2 regarding tips to avoid condensation problems Many of the recommendations contained in Chapter 2 will assist in avoiding exposure to chemicals that off gas Do Not Smoke Finally we recommend that you do not smoke inside your recreational vehicle In addition to causing damage to your recreational vehicle tobacco smoke releases formaldehyde and other toxic chemicals Medical Advice If you have any questions regarding the health effects of formaldehyde please consult your doctor or local health department Warranty Exclusion CHEMICAL OFF GASSING IS NOT A DEFECT IN YOUR RECREATIONAL VEHICLE AND IS NOT COVERED BY THE LIMITED WARRANTY PLEASE FOLLOW THE RECOMMENDATIONS IN THIS SECTION TO ADDRESS THIS CONCERN Chapter 10 Tire and Wheels The importance of Proper Tire Inflation Your trailer tires and wheels and tongue or fifth wheel hitch support the entire weight of the trailer and its contents The tires are also the only contact the trailer has with the road surface Determining and maintaining proper inflation is the most important factor in maximizing the life of your tires Driving on a tire that does not have the correct inflation pressure for the trailer load is dangerous and may cause premature wear tire damage tread delamination and or loss of control of the trailer and or tow vehicle An underinflated tire will build up excessive heat that may go beyond the limits of th
106. ltra violet damage and high seed towing in hot conditions also reduces tire life As heat builds up during driving the tire s internal structure starts to break down compromising the strength of the tire Have your tires inspected by a tire supplier to determine if your tires need to be replaced Replacement Tires To maintain tire safety purchase new tires that are the same type size construction and load rating as the original tires Look at the tire information placard or the sidewall of the tire you are replacing to find this information If you have any doubt about the correct size to choose consult your tire dealer Tire Safety Information This portion of the Owner s Manual contains tire safety information as required by 49 CFR 575 6 The National Highway Traffic Safety Administration NHTSA has published a brochure DOT HS 809 36 that discusses all aspects of Tire Safety as required by CFR 575 6 It can be obtained and downloaded from NHTSA free of charge from the following web site http www NHTSA dot gov cars rules TireSafety ridesonit tires_index html Studies of tire safety show that maintaining proper tire pressure observing tire and vehicle load limits not carrying more weight in your vehicle than your tires or vehicle can safely handle avoiding road hazards and inspecting tires for cuts slashes and other irregularities are the most important things you can do to avoid tire failure such as tread separ
107. ly sensitive device known as a Ground Fault Circuit Interrupter which is designed to sense the slightest electrical short at those receptacles and instantly disconnect the current before a person can be injured Testing The GFCI receptacle should be tested at least once a month or prior to every trip To test the GFCI push the TEST button The RESET button will pop out Power is now off at all outlets protected by the GFCI receptacle Push in the RESET button in to restore power The test is complete when the reset button remains pushed in If the RESET button does not pop out when testing the GFCI is malfunctioning and no outlets should be used on this circuit as protection is lost Call your dealer if the GFCI malfunctions Maintenance This item requires no maintenance other than periodic testing as described above If for any reason this switch malfunctions do not attempt to repair yourself Contact an authorized repair facility 7 Way Plug A 7 pin plug supplies the electrical connection between the tow vehicle and the recreational vehicle This plug connects into a receptacle on the tow unit to allow operation of the recreational vehicle s marker lights taillights brake lights and electric brakes A charge line from the tow unit s alternator is also run to this receptacle which allows charging to the RV battery te ei a Common Ground ros _ tstSupssTon Yellow Center Auxiliary
108. ments in the manufacturer s owner manual Refer to Chapter 4 Plumbing Roof Flush the waste water system and sanitize Refer to Chapter 7 Flush the water heater tank Refer to Chapter 7 Replenish the water tank air pocket Refer to Chapter 7 Winterize your coach prior to the onset of freezing temperatures During extreme freezing temperatures it is recommended that the unit be winterized Damage to the plumbing system due to freezing is not covered under the warranty Remove all debris from the roof and thoroughly clean using a mild detergent Refer to Chapter 9 Inspect the roof seals for signs of deterioration Reseal areas as required Refer to Chapter 9 Glossary of Common RV Terms ACCESSORY WEIGHT The combined weight in excess of those standard items which may be replaced of automatic transmission power steering power brakes power windows power seats radio and heater to the extent that these items are available as factory installed equipment whether installed or not AC ELECTRICITY Alternating Current Standard Household 110 Volt AC current ANODE ROD Part of the water heater that attracts impurities in the water that cause corrosion Appendix 85 Appendix 86 BEAD The part of the tire that is made of steel wires wrapped or reinforced by ply cords and that is shaped to fit the rim BEAD SEPARATION This is the breakdown of the bond between components in the bead BIAS PLY T
109. mportant for ramp cargo trailers These trailers are designed to carry a variety of cargo and or vehicles in the cargo storage area These cargo items are typically heavy and you must consider how they are loaded Incorrectly loaded trailers can have too little weight resting on the hitch or pin and can become unstable when towing Therefore you must maintain a hitch weight percentage of 10 15 for travel trailers and 15 25 for fifth wheels Keep 60 of the cargo weight forward of the axle s centerline Ramp Trailer Loading The rear cargo door loading ramp gives you complete access to the trailer cargo area When lowered the loading ramp allows you to easily load rolling cargo bicycles small motorcycles and ATVs and small vehicles This section outlines the safety precautions you should take when loading and unloading cargo and vehicles as well as loading unloading procedures techniques and tips Ramp Trailer Loading Safety The loading ramp door area of your trailer can be a very hazardous part of your recreational activities Many combinations of hazards and a large volume of activities occur in this area Some of these hazards are Ramps and inclines Overhead obstructions Dissimilar surfaces that are often wet and slippery Poor lighting during night or early morning activities Other vehicular traffic Pedestrians Restricted views Awkward heavy or unbalanced loads Sheer drops Trailer creep Congested staging areas Acc
110. n occur 4 The operator should apply throttle smoothly and climb the ramp at low speed Too much or sudden increases in throttle will cause the vehicle to be harder to control and may cause the vehicle to impact the front of the trailer cargo are or over turn 5 Stop when fully in the trailer Keep handle bars mirrors etc away from the trailer interior walls The walls can be damaged by contact with hard shard objects 6 After loading close the fuel valve and run the engine until it stops motorcycles and ATVs Turn the ignition key off and remove it Set the parking brake For manual clutch machines leave the machine in gear Chapter 11 Ramp Trailers Do not load motorized cargo motorcycles ATVs etc by riding them up the ramp door Loss of control could cause serious personal injury Redwood does not recommend loading motorized cargo under power 11 Chapter 11 Ramp Trailers Failure to properly secure cargo could cause property damage injury and or death Do not smoke when filling the tank Before dispensing fuel turn off all engines and fuel burning appliances and ground the trailer Do not dispense fuel within 20 feet of an ignition source Potentially explosive fuel vapor may be present at fuel filling stations and during refueling of equipment with the fuel transfer system Never enter a fuel filling station or refuel equipment if your furnace or water heater is operating on prop
111. nding on f p outlet but a separate valve controls each tank The dump valves should remain closed even if connected to an exterior sewer hook up For proper dumping empty tanks only when they are nearly full The idea is to send a large volume of water through the tanks and hose at the same time to assist the solid waste in flushing from the system Dumping Instructions 1 Twist off the termination outlet cap 2 Connect the sewer hose by turning counterclockwise locking the end levers over the termination end 3 Place the other end of the sewer hose into an approved dump station inlet Open the black tank termination valve and drain Open the gray tank termination valve and drain If unit has 2 gray tanks drain one at a time Close termination valves Disconnect sewer hose and store Replace termination cap on the outlet Add chemical deodorant breakdown agent approved for RV use Wastewater tanks must be dumped at state approved locations oe eo If unit is equipped with the No Fuss Flush System perform flush at this time After the sewage tank has been emptied close the gate valves and put approximately five gallons of water in the sewage holding tanks This will help prevent solids from building up The addition of a deodorizing agent like Aqua Kem will help prevent odors 43 Chapter 6 Plumbing System For best results use only biodegradable toilet tissue specifically ma
112. ng The load limit of each tiedown used should be at least on half the working load limit of each tiedown that foes from an anchor point on the trailer to an attachment point on an article of cargo Check the tiedown manufacturer s specifications to determine working load limits NOTE Tiedown hardware is not supplied with your trailer Minimum Number of Tiedowns When an article of cargo is not blocked or positioned to prevent movement in the forward direction the number of tiedowns needed depends on the length and weight of the articles In all cases use enough tiedowns to secure the cargo from moving in any direction Heavy tool chests or cabinets may require tiedowns around the bottom middle and top to secure them Be sure to lock or secure drawers in these chests or cabinets so they can t open while traveling Keep handle bars mirrors etc away from the trailer interior walls The walls can be damaged by contact with hard sharp objects Cargo Loading Procedure Rear Door Loading Ramp Operation 1 Hitch the trailer to a tow vehicle before loading and unloading the rear cargo area Select a parking site where the edge of the rear door loading ramp will rest entirely on a flat level surface and the corners of the door will be supported Avoid soft sand or mud surfaces When the trailer is loaded the added cargo weight may cause the trailer is loaded the added cargo weight may cause the trailer and or tow vehicle to become stuc
113. ngs may be in your way when you load or unload cargo or vehicles Predict what may happen and think of the consequences of your actions If you are loading unloading alone are you physically capable of handling the load safely and keeping it under control Ask yourself what would happen if your load falls over slips off the ramp or falls out of the trailer If you are unable to control your cargo what will happen to it you and any other people equipment or materials if when it becomes uncontrollable If you tie down your load what will happen if a tie down comes loose What will happen if all tie downs come loose What will you do if someone else does something dangerous during your unloading unloading Decide what to do based on your abilities and the capabilities of your equipment Always use proper lifting techniques and personal protection equipment as necessary such as gloves helmets kneepads and other protective clothing Be sure your cargo does not exceed the capacity of your loading rant and the trailer Here are some general safety rules about loading and unloading your cargo trailer Other safety items will be covered throughout this section Always consider the equipment you are loading After use it may be hot wet slippery dirty or in some other condition that may be potentially hazardous In all situations follow the loading and weight guidelines in the Loading and Weighing chapter of this Owner
114. nufactured for RV use available from your dealer DO NOT leave any hose connected when not in use DO NOT add any check valves to this system 4A No Fuss Flush If equipped the no fuss flush kit has been installed to rinse the interior of the black tank Similar to the water fills located on the exterior of the unit a separate hookup is placed on the exterior Flush the tank after dumping by connecting the sewer hose and attaching a garden hose to the inlet labeled Sewer Valve Must be Open When Using This Inlet OR Black Tank Flush Open the water supply to full pressure to flush tank When water runs clear from sewer hose shut off water supply and disconnect garden hose from source Do not disconnect hose from flush inlet until water has drained from system Chapter 7 Slide Out Systems Redwood uses basically three types of slide room systems depending on the product application For specifics concerning your type of system please refer to the unit packet information Hydraulically Operated Systems WARNING FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH The Lippert Hydraulic Slideout System is intended for the sole purpose of extending and retracting the slideout room Its function should not be used for any other purpose or reason than to actuate the slideout room To use the system for any reason other than what it is designed for may result
115. nylon swivel nut The green swivel nut attaches to the outside of the cylinder valve with right hand threads Tighten the swivel nut by hand DO NOT use tools The safety features of this system prevent gas from flowing unless the connection is tight and will limit excessive gas flow In cases of extreme heat 240 to 300 F at the connection the connection to the cylinder will be shut down Procedure For Filling Propane Cylinders Equipped With An OPD Valve 1 Shut off tow vehicle and extinguish all appliance pilot lights when filling tanks Ensure that the hand wheel valve is in the closed position Attach the fill hose to the outlet on the valve Turn on the Propane source Open the bleeder valve on the Propane tank 10 percent Slowly open the cylinder bottle hand wheel valve approximately one quarter turn 7 As the cylinder starts to fill the hand wheel valve may be opened more One turn is all that is necessary to complete filling the tank 8 When the bleeder valve begins to spit liquid shut off the Propane fill source close the bleed screw on the cylinder then close the valve ed alla a Propane Gas Lines The primary manifold is a black pipe located beneath the unit Copper tubing with flare fittings is used as secondary lines running to the gas appliances If repairs are needed to these lines or any component of the Propane system DO NOT ATTEMPT to repair yourself and follow the above instructions Although your Pr
116. o extend or retract the room Care and Maintenance When operating the Lippert Electric Slide out System it is recommended that the moving parts be kept clean especially when operating in harsh climates or environments Road salt ice sand and salt water climates are examples of such conditions The moving parts can be washed with a mild soap and water solution Slide out care does not require any grease or lubrication Use of any grease or lubrication may affect the long term dependability of the system Chapter 7 Slide Out System Before operating the slide room assure there are no objects or people in the path of the room or the Slidetopper Do not use the slide out without being extended by design The Lippert Hydraulic Slideout System is designed to operate as a negative ground system A negative ground system utilizes the chassis frame as a ground and an independent ground wire back to the battery is necessary see page 19 for wiring diagram It is important that the electrical components have good wire to chassis contact Over 90 of unit electrical problems are do to bad ground connections 45 Chapter 7 Slide Out System During extended travel stays move the room in and out once or twice a week to help keep the seals and internal moving parts lubricated During long term storage periods it is advised to have the room retracted 46 Electrical Maintenance Ele
117. o operate the appliances and fixtures requiring 12 Volt DC power In essence utilization of the converter will reduce the usage of the RV battery The converter installed helps by trickle charging the RV battery when the trailer is plugged into AC power When connected to the tow vehicle the RV battery will also be charged When using AC power and having the RV battery hooked up check the electrolyte level more often if staying connected to AC for a lengthy period of time If remaining plugged into AC power for extended periods check the electrolyte level often in the RV battery Chapter 4 Electrical System Never replace circuit breakers or fuses of higher current rating than those originally installed This could overheat the wiring and start a fire 31 Chapter 4 Electrical System Exceeding the amperage rating of an adapter can cause low voltage which may cause damage to the appliances or other components It may also cause the adapter or the shore cord to melt leading to fire which could cause property damage personal injury or death Exceeding the amperage rating of an extension cord can cause low voltage which may damage appliances or other components It may also cause the extension cord to melt leading to fire which could cause property damage personal injury or death 32 GFCI Ground Fault Circuit Interrupter Bathroom and exterior receptacles are protected by a high
118. o wax flooring Flooring Plank For routine cleaning sweep or vacuum regularly to remove loose dirt grit Lightly soiled floors can be damp mopped with clear water Do not use cleaners that contain abrasives or solvents or promise one step mop and polish Permanent damage may result from use of these cleaners Wipe up any spills immediately Certain inks mustards polishes tars paints varnishes etc can cause stains If normal clean up does not remove the substance use a cloth dampened with mineral spirits and wipe lightly DO NOT USE MINERAL SPIRITS NEAR A FIRE HAZARD Glass and Mirrors Clean glass and mirrors as you would at home using a cleaner designed for glass To reduce spotting on outside windows use a squeegee promptly after rinsing with water For stubborn spots cleaning with a mixture of vinegar and water is recommended and is safe for most finishes Fabric and Upholstery Do not laundry upholstery fabrics Blot up stains promptly and use an upholstery cleaner or mild solvent depending on the stain Never soak the fabric and use as little water as possible Blot rather than rub Towel dry or have professionally cleaned Upholstery can be vacuumed regularly using a soft brush attachment Sinks Tubs and Toilets Many of these products are made of acrylics plastics or composite materials and use of non abrasive cleaners is recommended to protect the finish Use of harsh cleaning products can cause prema
119. o your unit Chapter 1 Warranty Notes Tow Vehicle Disclaimer In connection with the use and operation of Redwood recreational vehicles Redwood customers and owners of Redwood recreational vehicles are solely responsible for the selection and proper use of tow vehicles All customers should consult with a motor vehicle manufacturer or dealer concerning the purchase and use of suitable tow vehicles for Redwood products Redwood further disclaims any liability with respect to damages which may be incurred by a customer or owner of Redwood recreational vehicles as a result of the operation use or misuse of a tow vehicle NOTE REDWOOD LIMITED WARRANTY DOES NOT COVER DAMAGE TO THE RECREATIONAL VEHICLE OR THE TOW VEHICLE AS A RESULT OF THE OPERATION USE OR MISUSE OF THE TOW VEHICLE THE USE OF THE INCORRECT TOW VEHICLE MAY LEAD TO THE ROLLOVER OF THE VEHICLE AND OR FIFTH WHEEL AND RESULT IN SERIOUS INJURY OR DEATH 10 Chapter 2 Towing and Leveling Passengers are not permitted in Chapter 2 Towing and Leveling the coach while it is in motion Towing Guidelines Weight distribution is an important factor when loading your fifth wheel and travel trailer A recreational vehicle with the cargo distributed properly will result in efficient trouble free towing Loading the coach as evenly as possible and then weighing the loaded RV can accomplish proper weight distribution Keep heavier items as
120. om an outside phone and follow their instructions Do not turn on the gas supply until the gas leaks have been repaired If no gas smell present light a match depress and turn oven control knob to Pilot On and light pilot Operation of Oven Burner Depress oven knob and turn to desired setting A delay of appx 45 seconds will occur before burner is lit This is normal To Shut Down Oven Burner Turn oven control knob to Pilot On position This will keep the oven pilot lit To Shut Down Oven Pilot Turn oven control knob to OFF position Care and Maintenance Before cleaning make sure all knobs are in the OFF position and wait until all surfaces including burners are cool Use warm soapy water only Do not use oven cleaners bleach or rust removers on the range cook top surface Wipe up any spills as soon as possible to avoid possible discoloration or pitting on the surface Check burner ports when cleaning If the ports or the orifice is clogged carefully clean with a toothpick Follow the instructions and warnings noted in the appliance and equipment owner s manual as well as the ones listed below Annual maintenance should be conducted on the propane appliances and equipment by an authorized dealer or repair facility Insects can build nests in the burners of the various appliances and equipment The burner and burner orifice of the propane appliances and equipment should be cleaned out by an
121. on or any damage to the vent covers or case Tighten any loose clamps on the terminals of the battery and clean any corrosion off the terminals An inexpensive device for cleaning these terminals can be purchased at automotive stores When working with batteries be extremely careful The acid in Vent Cover batteries is highly corrosive and flammable Batteries produce a flammable hydrogen gas that will explode if ignited Never place Electrolyte batteries in any compartment or Level near anything that could spark Plate even a 12 Volt switch Never smoke or use open flames anywhere near the battery Secure batteries in a battery box or in a compartment specially designed for battery storage Wear splash proof goggles and appropriate clothing when performing any maintenance on a battery In case of a spill or splash immediately flush the affected area with cold water for 15 minutes and call the poison control center for further instructions We do not cover batteries under warranty Battery Storage When storing the RV for an extended period fully charge the battery before storage Batteries will self discharge over time and are subject to freezing especially if in a discharged condition Inspect batteries while in storage every 2 to 3 weeks Hook up a battery charger at least once a month to prevent discharge and sulfation An easy solution is to remove the battery completely from the unit during storage and place it at
122. on transferable and applies only to units sold in the United States and Canada by authorized Redwood dealers Written notice of a defect must be given to the selling dealer or Redwood no later than ten 10 days after the expiration of the limited two year warranty Chapter 1 Warranty Chapter 1 Warranty Redwood at its sole discretion reserves the right to substitute parts or components of substantially equal quality repair cosmetic flaws make design and or manufacturing improvements as the exclusive remedy under this Limited Warranty All owners must be properly registered with Redwood in order to obtain the benefits of this Limited Warranty Structural Warranty Coverage The recreational vehicle structure manufactured by Redwood is warranted to be free from manufacturing defects in material and workmanship for a period of five years beginning on the date of the original purchase The structure is defined as 1 The rafter structure of the roof 2 The stud structure of the front rear and sidewalls excluding slide outs 3 The laminated exterior skin of the sidewall 4 The joist structure of the floor This structural warranty does not include components not manufactured by Redwood including but not limited to frame windows doors Alpha ply roof material vents and cabinets An annual inspection must be performed by an authorized Redwood dealer to qualify for the five year structural warranty coverag
123. on range exhaust hood Check for obstructions and dirt on exterior appliance vents Clean smoke detector components Test smoke detector operation Check fire extinguisher pressure and condition T voasa x Wear ara Dirutan x ses owas TREBE Towable Brakes rowami Be sure unit is within specified toad limits amp weight distribution _ Mounting bolts should be torqued to 145 155 foot pounds Repack wheel bearings yearly X Check operation and or uneven wear 59 Chapter 9 Chemical Sensitivity 60 Chapter 9 Condensation Chemical Sensitivity Ventilation To Avoid Condensation Problems Follow These Tips e Allow excess moisture to escape to the outside when bathing washing dishes hair drying laundering and using appliances and non vented gas burners e Always use the vent hood when cooking e Keep the bathroom door closed and the vent or window open when bathing and for a period of time after you have finished e Do not hang wet clothes in the coach to dry e In hot weather start the air conditioner early as it removes excess humidity from the air while lowering the temperature e Keep the temperature as reasonably cool during cold weather as possible The warmer the vehicle the more cold exterior temperatures and warm interior temperatures will collide on wall surfaces creating condensation e Use a fan to keep air circulating inside the vehicle so condensation and mildew cannot
124. ontain high levels of iron or sulfate Another important maintenance procedure is periodically checking the water heater screen in the exterior door for any obstructions such as animal insect nests or debris Proper ventilation is essential to the safe operation of the water heater A qualified technician should do any repairs that need to be performed If soot is present anywhere immediately shut the unit down and contact a qualified service technician Soot is a sign of incomplete combustion and must be corrected before operating the water heater Pressure Relief Valve Weeping or Dripping As in residential water heaters the water heater equipped in recreational vehicles contain a pressure relief valve that is designed to open if the temperature of the water within reaches 210 degrees F or if excessive pressure is built up When pressure reaches 150 pounds the relief valve will open and water will drip from the valve The valve will close automatically once the pressure falls below 150 pounds This dripping is normal and does not indicate a malfunctioning or defective valve Also as water is heated it expands and with the closed water system in a recreational vehicle water expansion will cause weeping at the pressure relief valve One way to minimize this weeping is by maintaining an air pocket at the top of the water heater tank The air pocket forms naturally by design but will reduce overtime through normal use Replenishing the Ai
125. opane gas system was thoroughly inspected for leaks before delivery gas fittings can loosen from vibration during travel The Propane gas system should be inspected at least once a year Propane Gas Leak Detector Read the operating instructions located in the unit packet thoroughly for the specific model installed in the unit The Propane gas leak detector is a safety device that is permanently mounted near the floor and is powered by 12V the RV battery and or converter The detector is operational only as long as sufficient battery power is available If the power is disconnected the monitor will not operate Should a propane leak occur the detector will sound an alarm and continue until the gas has dissipated or until a mute button is pressed The mute button will only stop the alarm from sounding for 60 seconds and will reoccur if gas is still present Sometimes in new coaches an alarm will sound due to the odor in a new trailer from glues and other materials used to build the unit The alarm also may sound at times when no Propane is present due to household product use such as aerosol Chapter 5 Propane Gas System Propane powered appliances produce carbon monoxide Carbon monoxide can be fatal When the device detects carbon monoxide in the air it will sound Consult the individual detector s user manual for specific instructions and or audible warning meanings DO NOT attempt to adjust or repair regula
126. ost states it is illegal to dump your tanks anywhere except at dump stations DUMP VALVE Another name for the T Handle used to drain the black and gray tanks EGRESS WINDOW Term for the emergency exit windows within recreational vehicles Usually identified by a red handles or levers EXTRA LOAD TIRE A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire FULL HOOK UP SITE A Campsite that offers full amenities City water sewer and electrical hook ups many have cable and phone available GALLEY TANK A gray water holding tank used specifically for the kitchen waste water GENERATOR Powered by Propane gas generates 110 Volt power GRAY TANK the waste holding tank into which water from the kitchen and bath sinks shower and tub drains GRAY WATER Water drained into the gray holding tank GROOVE The space between two adjacent tread ribs GROSS AXLE WEIGHT RATING GAWR Maximum amount of weight in Ibs that can be placed on the axle GROSS COMBINED WEIGHT RATING GCWR Maximum load weight in Ibs allowed for the coach and tow vehicle GROSS VEHICLE WEIGHT RATING GVWR Maximum load weight in lbs allowed for the vehicle GROSS Fifth Wheel WEIGHT GTW Weight of the fully loaded coach in its actual towing condition Appendix 87 Appendix 88 HITCH WEIGHT Amount of a coach s weight that rests on the tow vehicle s
127. pairs are in or out of warranty It is the responsibility of the dealer to submit the unit warranty registration to Redwood RV within 30 days of retail delivery date The dealer should also assist the customer in completing all necessary registrations for factory installed components and locating the serial numbers if needed Redwoad s Responsibilities Please note the distinction between defects and damage as used in this Limited Warranty Defects are covered because Redwood is responsible whereas damages are not covered because Redwood did not cause the damage Damages are caused by misuse collision or lack of maintenance that occurs after the recreational vehicle is delivered to the owner Damage for any reason that occurs after the recreational vehicle is delivered to the dealer s lot is not covered under this warranty Redwood does not undertake responsibility to any owner beyond the original cost of the recreational vehicle to Redwood or for any undertaking represen tation or warranty made by any dealer beyond those expressed herein Limited Two Year Warranty Except as specifically excluded below Redwood RV hereinafter Redwood warrants for a period of two 2 years from the date purchase that the recreational vehicle manufactured and assembled by Redwood shall be free from defects in materials and workmanship supplied and attributable to Redwood This Limited Warranty extends to the first retail purchaser is n
128. parting of cords from adjacent rubber compounds CRACKING Any parting within the tread sidewall or inner liner of the tire extending to cord material CT A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire CURB WEIGHT The weight of a motor vehicle with standard equipment including the maximum capacity of fuel oil and coolant and if so equipped air conditioning and additional weight optional engine DC ELECTRICITY Direct Current Also termed Battery Power Used to run all 12 Volt powered systems or lighting DRY CAMPING Refers to camping using only the resources within your unit and without amenities such as city water hook ups electrical hook ups etc often provided at commercial campsites DSI IGNITION Direct Spark Ignition The method of lighting a main burner on a Propane fired appliance DUCTED AC Air conditioning distributed through a ducting system DUCTED HEAT Warm air distributed through a ducting system DUAL ELECTRICAL SYSTEM Coach equipped with appliances and lights which operate on 12V power when self contained and with a converter on 110 AC when in campgrounds or run off of a generator DUMP STATION Term used for locations to drain the waste holding tanks gray and black tanks In m
129. plied The Limited Warranty and limited warranties issued by the component manufacturers require periodic service and maintenance and the owner s failure to provide these services and or maintenance may result in loss of warranty coverage for that item The owner should review Redwood RV Company s limited warranty and the warranties of all other manufacturers Instructions included in this manual are for operating some components which may be optional on your vehicle This manual is devoted to instructions on fifth wheels We hope you have many years of vacationing pleasure This manual is based on the latest information available at the time of publication Due to continuous product development and improvements Redwood RV Company reserves the right to make changes in product specifications and components without prior notice September 2011 Introduction Danger Warning Caution and Note Boxes We have provided many important safety messages in this manual Always read and obey all safety messages DANGER indicates an imminently hazardous situation that if not avoided will result in death or serious injury WARNING indicates a potentially hazardous situation that if not avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury CAUTION used without the safety alert symbol indic
130. r Pocket 1 Turn off water heater 2 Turn off cold water supply 3 Open a faucet in the RV 4 Allow time for water to cool and Pull out handle of the Pressure Relief Valve and allow water to flow from the valve until it stops 5 Release handle on valve it should snap shut 6 Close faucet and turn on cold water supply as tank fills the air pocket will be replenished Water Supply and Odor Water supplies sometimes contain high levels of sulphur which causes an unpleasant smell similar to rotten eggs While unpleasant the water is not harmful Sanitizing the water system as described earlier and allowing the sanitizing solution to remain for a few days should eliminate the odor Remember to thoroughly flush the system after sanitization Adding a filtration system will help reduce such occurrences Draining and Storage When not using for long periods or storing during the winter months the water heater must be drained to avoid damage from freezing during the winter and or deterioration of tank life from mineral content in water supplies To Drain the Water Heater 1 Turn off power to the water heater at the switch or the main breaker Shut off the gas supply and the water pump Open all fixtures both hot and cold throughout the unit Place the bypass valve if equipped in the by pass position Remove open the exterior access door to the water heater Remove the anode rod from the tank Water will drain out tan
131. re gauge is a very inexpensive and valuable tool for checking tire inflation Rotate the tires at lest once every 5 000 miles You may want to have a spare tire with you in case of an emergency All travel trailers and fifth wheels are equipped with tubeless tires They are designed for today s turnpike speeds are rated to carry the weight of the trailer plus your family s personal needs for an extended vacation If you should require an adjustment on a fault or defective tire secure the name of the nearest tire dealer or distributor and request an adjustment according to the conditions and terms of the tire warranty Tire Changing Basics 1 Use emergency flares when near a road or highway 2 Block the wheels on the opposite side from the tire you wish to change to prevent accidental movement 3 Position a hydraulic jack on the frame close to the spring hanger Never attempt to use a stabilizer jack to lift the unit 4 Raise the trailer until the tire clears the ground Tire Inspection The chart below is a useful guide for use during inspections When replacing tires consult the wheel and tire manufacturers specifications for compatibility Wheel Nut Torque The information contained in these printed instructions outlines the most recently recommended processes involving Lug Nut Torque and takes precedent over any information regarding Lug Nut Torque shown in your Lippert or AL KO Owners Manuals The axle and wheel a
132. rial chemical used in the manufacture of the numerous consumer products which we referred to above and used in the construction of recreational vehicles Trace levels of formaldehyde are also released from smoking cooking use of soaps and detergents such as carpet shampoos cosmetics and many other household products Some people are very sensitive to formaldehyde while other may not have any reaction to the same levels of formaldehyde Amounts released decrease over time Chapter 9 Chemical Sensitivity If using a dehumidifier please read and follow all manufacturer instructions and recommendations for use and cleaning 61 Chapter 9 Chemical Sensitivity Check tire pressures before traveling Always check tire pressure when tires are cold Do not exceed the maximum recommended pressure 62 Ventilation To reduce or lessen exposure to chemicals from off gassing it is of utmost importance that you ventilate your recreational vehicle Ventilation should occur frequently after purchasing and at times when the temperatures and humidity are elevated Remember off gassing is accelerated by heat and humidity open windows exhaust vents and doors Operate ceiling and or other fans roof air conditioners and furnaces and use a fan to force stale air out and bring fresh air in Decreasing the flow of air by sealing the recreational vehicle increases the formaldehyde level in the indoor air Please also fol
133. rous sway Do not overcrowd or cross the center line All sharp turns should be taken at low speeds Professional drivers when rounding turns slow down well in advance of the turn entering it at reduced speed and then accelerate smoothly as they come out again into the straightaway Steep or Long Grades Down shifting into a lower gear or range in advance assists braking on descents and adds power on the climb Avoid situations that require excessive and prolonged use of the brakes Apply and release brakes at short intervals to give them a chance to cool Slippery Pavement On slippery and icy pavement reduce speed and drive slowly Hydroplaning can occur with little water on the pavement If skidding begins remove your foot from the throttle and gently apply the trailer brakes only Freeways and Highways Try to pick the lane in which you want to move and stay in it preferably keeping to the slower lane on the right Turning Corners Here is where you find a first basic difference when towing The trailer wheels do not follow the path of your tow vehicle s wheels The trailer will make a closer turn than the tow vehicle Compensate by pulling further into the intersection so that the trailer will clear the curb or clear any parked vehicles along the road Left turns require a wider than normal swing into the new lane of traffic to keep the trailer from edging into the opposing lane Use the turn signals early to communicate
134. rowth to occur temperatures indoors or outdoors must be between 40 degrees and 100 degrees Fahrenheit and there must be a source of moisture such as humidity standing water damp materials etc Indoors the most rapid growth occurs with warm and humid conditions How can mold growth be inhibited By controlling relative humidity the growth of mold and mildew can be inhibited In warm climates use of the air conditioner will reduce the relative humidity Vents are located in the bathing and cooking areas and constant use is advised during food preparation and bathing even during colder weather Additionally opening a window during these activities will assist in ventilation In extremely humid conditions using a dehumidifier can be helpful Frequent use of your RV or cleaning regularly is an important preventive measure Further any spills should be wiped up quickly and dried as soon as possible Avoid leaving damp items lying about On safe surfaces use mold or mildew killing cleaning products Check sealants regularly and reseal when necessary to avoid water leaks Proper preventive maintenance to the RV and its accessories as described both in this manual and in accompanying literature will provide the best protection to the RV For more information of controlling moisture in the RV please read Tips to Controlling Condensation located in this manual If using a dehumidifier please read and follow all manufacturer
135. s 110V from an exterior outlet such as campgrounds to the RV Also called Power Cord SHORE POWER The 110V outlet that connects to the Shore Line SIDEWALL That portion of a tire between the tread and bead SIDEWALL SEPARATION The parting of the rubber compound from the cord material in the sidewall TEST RIM The rim on which a tire is fitted for testing and may be any rim listed as appropriate for use with that tire TREAD That portion of a tire that comes into contact with the road TREAD RIB A tread section running circumferentially around a tire TREAD SEPARATION Pulling away of the tread from the tire carcass TREAD WEAR INDICATORS TWI The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread UNLOADED VEHICLE WEIGHT UVW Weight of the unit without adding fuel water propane supplies and passengers Also referred to as Dry Weight VEHICLE CAPACITY WEIGHT The rated cargo and luggage load plus 68 kilograms 150 Ibs times the vehicle s designated seating capacity Vehicle maximum load on the tire The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing by two VEHICLE MAXIMUM LOAD ON THE TIRE The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing by two VEHICLE NORMAL LOAD
136. s and maintenance can be found in the Care and Maintenance section Level Towing Having the tow vehicle and recreational vehicle level with each other will help improve towability as well as safe driving A hitch that is too low can cause the front to drag A hitch that is too high can cause the rear to hit those high spots in the road Lights Check all electrical connections to ensure all lights on the tow vehicle and travel trailer are functioning properly The break lights hazards and turn signals should be in synchronization with the tow vehicle Mirrors Adjust the mirrors on the tow vehicle prior to departure Having someone to assist you will make this safety step quick and easy First line up the tow vehicle and trailer Next sit in the driver s seat and adjust the left mirror to where you can see the entire left side of the trailer and well beyond Finally while still sitting in the driver s seat have someone adjust the right mirror until the same result is achieved While Driving Driving with a trailer in tow is different Start out slowly checking the traffic after signaling and being sure the road is clear Accelerate slowly and evenly checking the mirrors frequently as you move into the proper lane Try to drive with an anticipation of problems that may occur way ahead and prepare for them even though they may never happen As a motorist sharing the road you are taller heavier longer and require more time and
137. s completed reviewed and signed prior to leaving the dealer ship Get To Know Your Unit Before Heading Out Throughout the manufacturing process your recreational vehicle has been inspected by qualified inspectors and then again at the dealership As the owner however you will be the first to camp and extensively use every system Redwood RV wants the first camping experience to be a happy one and recommends a trial camping experience before heading out Plan a weekend in the yard or driveway and really camp in your unit By camping for several days full time in your unit you will have the opportunity to use and become accustomed to the systems within your unit and find out what items will be needed while camping Note any questions that arise difficulties encountered or problems that occur After your trial call your dealer with any questions or concerns you may have Getting to know your unit before the first adventure can save a lot of frustration and leave more time for fun Chapter 1 Warranty Obtaining Warranty Service Redwood RV recommends obtaining service from the selling dealer or the nearest authorized repair facility The owner must deliver the recreational vehicle to the repair facility within a reasonable time after discovery of the defect within the warranty period If assistance is needed in locating an authorized repair center please go the Dealer Locator on our website Please refer to the last page ww
138. s levels of carbon monoxide gas can accumulate in a trailer which cannot be detected by sight smell or taste Even small quantities of carbon monoxide can cause carbon monoxide poisoning and suffocation which will cause death serious injury or permanent disability Exposure to high concentrations of carbon monoxide for even a few minutes will also cause death serious injury or permanent disability DO NOT start ATVs motorcycles or other fuel burning devices while they are located in your trailer ee gt gt amp A Doors and windows in walls of separation if installed shall be closed while the vehicles are present Fuel shall be run out of engines of stored vehicles after shutting off fuel at the tank Motor fuel shall not be stored or transported inside this vehicle The vehicle storage area shall be ventilated Gas appliances pilot lights or electrical equipment shall not be operated when motorized vehicles or motorized equipment are inside vehicle FAILURE TO COMPLY COULD RESULT IN AN INCREASED RISK OF FIRE EXPLOSION ASPHYXIATION DEATH OR SERIOUS INJURY Many recreation ATV or motorcycle accidents and injuries happen while loading or unloading Steep inclines unstable ramps power and a short stopping area are what make loading motorized cargo difficult and unsafe There is no absolute safe way to drive your motorized cargo into the trailer Take the following steps to aid in reducing
139. s of the tires alone A Federal Certification Label is located on the forward half of the left road side of the unit The certification label will indicate the vehicle s gross vehicle weight rating GVWR This is the maximum weight a particular axle can carry If there are multiple axles the GAWR of each axle will be provided In the same location as the certification label described above there is a vehicle placard This placard provides tire and loading information In addition this placard will show a statement regarding maximum cargo capacity Cargo Capacities Cargo can be added to the vehicle up to the maximum weight specified on the placard The combined weight of the trailer and the cargo is provided as a single number In any case remember the total weight of a fully loaded vehicle can not exceed the stated GVWR Water and propane also need to be considered The weight of fully filled propane containers is considered part of the weight of the RV before it is loaded with cargo and is not considered part of the disposable cargo load Water however is a cargo weight and is treated as such If there is a fresh Chapter 10 Tire Safety Information IMPORTANT SPECIAL NOTICE Your trailer is equipped with tires designated as ST This designation means that the tires are built specifically for trailer applications They are correct for your trailer and the maximum loads the trailer was designed and rated to carry
140. ssemblies of your RV are designed differently than those on your car The overall size weight and center of gravity of a recreational vehicle subject the wheels to pressures unique to trailering During normal cornering the tires and wheels experience a considerable amount of stress called side load Therefore the lug nuts on your recreational vehicle require periodic retorqueing These instructions will show you how to maintain proper lug nut torque by following these important steps iP Check torque before every trip 2 Use proper tools 3 Follow the appropriate ANSI TSIC 1 Recommended Practice at right 4 Torque lug nuts in the correct stages and follow up intervals after any wheel reinstallation For further information on these steps you may want to refer to the axle manufacturer s owner s manual that accompanied your unit Remember torque is the amount of rotating force applied to a fastener such as a lug nut Proper torque of lug nuts can only be achieved by using a torque wrench and a socket Dial indicator or Adjustable dial torque wrench 7 8 or 13 16 socket Using Torque Wrenches e Most torque wrenches are required to be set at 0 when not in use to maintain calibration Please refer to the manufacturer s instructions for further information on use and maintenance Setting Torque Value on a Dial Indicator Wrench 1 Make sure your indicator needle is set to 0 2 As yo
141. stribution is of particular importance for ramp trailers These trailers are designed to carry a variety of internal combustion engine vehicles in the transportation storage area These cargo items are typically heavy and consideration must be given to how they are loaded Because most storage areas are at the rear of the vehicle the biggest concern is maintaining the correct hitch or pin weight percentage Vehicles loaded incorrectly can have too little weight resting on the hitch or pin and can become unstable when towing Therefore a hitch weight percentage of 10 15 for travel trailers and 20 25 for fifth wheels must be maintained For example if the loaded vehicle weighs 8000 pounds the hitch weight for a travel trailer should be between 800 1200 pounds 10 15 of the 8000 pound total For a fifth wheel this same 8000 pound vehicle should have a pin weight of 1600 2000 pounds 20 25 By maintaining the correct hitch percentage and staying within the limits of the GVWR and GAWR you can insure a safe towing experience with your trailer Stabilizing Jacks Dependent upon the type of trailer product and model purchased the stabilizer jacks included will vary Although stabilizer jacks come in different types and sizes all perform the same function To stabilize the front and rear of all recreational vehicles while parked for camping Always park the recreational vehicle on level ground and use tire chocks lt is e
142. t and model To determine how much fresh water the system can hold refer to the RVIA TRAILER WEIGHT INFORMATION label located on the inside of the kitchen cabinet door near the sink The full capacity rating of fresh water for the travel trailer fifth wheel includes the cumulative total of the tank lines and the hot water heater tank Fresh Water Fill To fill the fresh water tank remove the cap on the exterior connection labeled Fresh Water Connection and insert a garden hose Check the monitor panel to determine the level of water in the tank during filling When full water may spill out back through the valve as there is no automatic cutoff When filling the fresh water tank it is a good idea to also fill the hot water heater and lines to provide the maximum system capability When traveling with the water tank full the cargo carrying capacity is reduced Water should be drained from the fresh water system when not in use for more than one week City Water Fill The city water fill allows a direct connection to an outside source such as Campsites with water risers There is no need to use the water pump as the water coming from the exterior source is already pressurized and will bypass the pump and tank Connect the city water fill by using a hose manufactured for potable water use Open faucets and allow any air to be purged City water fills are marked with a label and may be installed as a separate piece of equipmen
143. t or as a part of a combination water inlet housing Sanitizing the Fresh Water System Keeping the fresh water system clean and free of any potential contaminations is a top priority Sanitizing the system before initial use and thereafter annually or whenever water remains unused for prolonged durations is recommended This will help keep the water system fresh and discourage harmful bacterial or viral growth To sanitize your system perform the following 1 Drain the tank by opening the low point drain for the fresh water tank 2 Prepare a chlorine bleach solution of 14 cup to one gallon of water for every 15 gallons of tank capacity Example Use 2 gallons of the solution for a 40 gallon tank If using Ultra bleach concentrations reduce bleach to 1 8 cup to one gallon of water 3 Add solution to tank and fill with water Open each faucet fixture until a distinct chlorine odor is smelled Close faucets and let stand 4 hours 4 Drain system and flush with fresh water until chlorine odor and smell is gone If a water filter has been added change it at this time Chapter 6 Plumbing System Propane gas may be present in other areas before it can reach the detector s location The detector only indicates the presence of Propane gas at the sensor Never check for leaks with open flame Use only a mild soap and water solution 4 NOTICE Never let the water pump run while the fresh water tank is empt
144. t things you can do to avoid tire failures are maintain proper tire pressure stay within tire and vehicle load limits avoid road hazards if possible inspect tires for cuts slashes and other irregularities Properly maintained tires improve the steering stopping traction and load carrying capability of your vehicle Make tire safety a regular part of your vehicle maintenance routine Recognize that the time you spend is minimal compared to the inconvenience and safety consequences of a flat tire or other tire failure Understanding Tire Pressure and Load Limits Tire inflation pressure is the level of air in the tire that provides it with load carrying capacity and affects the overall performance of the vehicle The tire inflation pressure is a number that indicates the amount of air pressure that a tire requires to be properly inflated It is difficult to obtain the recommended tire pressure if your tires are not cold Because tires are designed to be used on more than one type of vehicle tire manufacturers list the maximum permissible inflation pressure on the tire sidewall This number is the greatest amount of air pressure that should ever be put in the tire under normal driving conditions Cheching amp Adjusting Tire Pressure It is important to check your vehicle s tire pressure at least once a month always before a trip and at least once a week while on the road Not only do tires naturally lose air over t
145. t to the first stage Brakes should audibly engage Double check by moving the tow vehicle forward slightly to be sure the RV brakes have locked and are operating correctly 0 Chapter 5 Propane Gas System Read all manufacturer appliance literature including the information on the Propane bottles and regulator provided within the unit packet and follow any instructions given General Information Propane gas also called LPG Liquefied Petroleum when properly handled is a clean burning dependable fuel for operating all Propane gas appliances The Propane gas system involves the tank s Also called bottles or cylinders regulators valves supply lines and appliances Propane tanks contain liquid under high pressure which vaporizes into a gas and passes through the regulator to automatically reduce the pressure Low pressure gas is then distributed through the supply lines to provide the fuel for Propane appliances Consumption of Propane gas depends upon the frequency and duration of use of the Propane appliances The furnace and oven have the highest consumption rates During cold weather it is advisable to check the bottles often and always keep one full Safety must be observed at Chapter 4 Electrical System 33 Chapter 5 Propane Gas System The breakaway switch is for emergency use only 34 all times when using the Propane gas system Propane gas is colorless and odorless in its natural
146. t wheels of your tow vehicle into the curb and set the parking brake For added safety place wheel chocks under the trailer wheels on the down roadside Fifth Wheel Leveling Procedures 1 Choose a site that is as level as possible Some sites are equipped with a prepared surface such as concrete or asphalt Ensure the ground is not soft and will support the weight of the fifth wheel on the stabilizing jacks or other support devices 2 Before uncoupling level the fifth wheel from side to side with suitable lengths of 2 x 6 wood blocks under the coach s wheels Place the wood blocks on the ground forward of the wheels and tow the unit onto the blocks Block the wheels to be sure the fifth wheel cannot roll 3 Lower the quick drop landing gear legs before extending the landing gear The positioning of the quick drop legs will depend upon how level your campsite is from side to side and front to rear The landing gear is then extended It may be necessary to place a sturdy 2 x 6 wood block under the foot pads to support the landing gear on soft ground surfaces 4 After stabilizing the unit be sure the fifth wheel frame is not twisted buckled or stressed Check that all doors and windows operate freely and do not bind 5 Before resuming travel be sure the stabilizer jacks are fully retracted Ramp Trailer Weight Distribution All loaded trailers must remain within GVWR and GAWR limits However proper load di
147. te that the dome of the vent must be opened at least three inches for the motor to operate A safety switch will prevent operation if the dome is closed or open less than three inches Furnace The furnace installed is a Propane gas appliance Carefully read the manufacturer s manual for complete operational and safety instructions provided in the unit packet prior to using the appliance The furnace utilizes a sealed combustion system which means the combustion chamber is completely sealed from the inner atmosphere of your vehicle Combustion air is drawn from the outside and combustion products are expelled outside through a vent New furnaces sometimes emit smoke and an odor during the first 5 10 minutes of initial use due to paint burning off the heating chamber Do not mistake this for a malfunctioning furnace Opening the windows and door prior to first lighting will help vent any smoke or odor Thermostat Wall Mounted Redwood travel trailers and fifth wheels have either a heat only thermostat or a combination air conditioner furnace thermostat if an air conditioner is equipped at the factory Please refer to the user s manual for the specific thermostat installed Operation Heat Only Thermostat To turn ON Set temperature to desired level To turn OFF set thermostat to lowest setting and follow instructions for furnace operation in the manufacturer s user s guide Heat Operation A C and Heat T
148. tempt to press on the accelerator to speed your way out of the fishtailing Both actions make the situation worse and could cause severe injury or death 4 Once the swaying is under control stop as soon as possible Check tire pressures cargo weight distribution and look for any signs of mechanical failure Travel at reduced speeds that permit full control until the problem can be identified and corrected Before Heading Out Weight Distribution Proper weight and load distribution is absolutely essential to safe towing It is necessary to maintain a certain percentage of gross vehicle weight on the tow vehicle Common recommendations place approximately 10 15 of a loaded weight on a travel trailer hitch and approximately 20 25 on a fifth wheel pin weight as the weight comes out of the tow vehicle payload capacity Too much or too little weight upon the hitch leads to dangerous driving conditions such as sway and reduced tow vehicle control In no circumstance should the loaded weight ever exceed the GVWR or the GAWRs Safety Chains Always use safety chains when towing They maintain the connection between the travel trailer and tow vehicle in the event of separation of the ball and trailer coupling Safety chains are included with every travel trailer and in most states are required when towing a travel trailer Hook them to the frame of the tow vehicle not the hitch crossing them under the trailers tongue Inspect the length
149. the RV prior to greasing axles To grease follow these simple steps Remove the rubber plug from the grease cap Insert grease gun on the grease zerk Pump until new grease begins to appear Replace rubber plug m Hubs and components still need to be inspected and maintained per the manufacturer s guidelines Carefully read the component manufacturer s manual and any safety instructions provided in the unit packet prior to performing any maintenance Brake Adjustment The electric brakes are of the drum and two shoe type and adjust the same as most automotive brakes Adjust brakes after the first 200 miles Every 3 months or 3000 miles test the brake drag and adjust if required Full procedures are outlined in the component manufacturer s guide included in the unit packet Never adjust just one brake When adjusting brakes on any vehicle either replace or adjust all brakes at the same time or at least both brakes on the same axle Battery Before performing any maintenance on the battery always disconnect the To inspect the electrolyte level remove the vent covers and visually ascertain the electrolyte level in each cell using a small flashlight may help If a maintenance free battery has been purchased no way exists to check these levels If the level needs to be replenished in any or all cells carefully pour in distilled water only Never use acid or tap water Chapter 8 Care amp Maintenance Do not
150. the risks associated with transporting storing or occupying the trailer with motorized equipment and vehicles Wear personal protective equipment while loading and unloading vehicles to from the trailer This includes but is not limited to an approved motor vehicle helmet leather boots appropriate gloves and eye protection Never stand in the path of equipment when loading unloading with the ramp and keep bystanders away from the ramps Keep body parts completely clear of the ramp door hinge pinch area at all times Check parking brakes on the vehicle s you are loading unloading and on the tow vehicle Inspect ramp and trailer floor loading area for cracks damage oil or other debris that may cause slippage Do not allow persons or pets to ride inside the vehicle storage area at any time Close doors and windows in separation walls while the vehicles are present Close tank fuel valves and operate the engine s to run fuel out of engine s of stored vehicles Do not store or transport motor fuel anywhere inside the trailer Ventilate the interior of the trailer to reduce the risk of fire explosion or asphyxiation Do not operate gas appliances pilot lights or electrical equipment when motorized vehicles or motorized equipment are inside the trailer FAILURE TO COMPLY COULD RESULT IN AN INCREASED RISK OF FIRE EXPLOSION OR ASPHYXIATION Load and store your equipment and motorized vehicles according to the
151. tion while applying Laminate Countertops Dust and clean with a soft damp cloth or chamois wiping surface gently Use pure soap and lukewarm water to clean The manufacturer also suggests cleaners like 409 or Fantastik Strong soaps and abrasive cleaners should not be used Light scratches can be removed by waxing with Simonize wax Draperies Draperies and upholstery fabrics should always be dry cleaned like any other fine fabric by a competent dry cleaning establishment Many window treatments and bedspreads are fire retardant When dry cleaning be sure to inform attendant of fire retardant items Spots and stains should be removed with a non water based commercial spot remover manufactured for this purpose Chapter 8 Care amp Maintenance 55 Chapter 8 Care amp Maintenance 56 Faucets and Fixtures To protect the finishes on your kitchen and bath faucets and fixtures use only a damp soft cloth or sponge Do not use abrasive cleaners or materials as they can damage the finish Flooring Vinyl For routine cleaning sweep or vacuum regularly Follow by using a damp mop with warm water and clean a small area at a time Rinse the mop frequently as to not redistribute the dirt picked up If washing is needed use a quality product designed for no wax flooring To polish the floor do not use solvent based waxes or polishes as damage to the flooring may result Use only polishes recommended for n
152. to carry Both placards and certification labels are permanently attached to the trailer on the forward half of the left side and are easily readable from outside the vehicle without moving any part of the vehicle Tire Repair The proper repair of a punctured tire requires a plug for the hole and a patch for the area inside the tire that surrounds the puncture hole Punctures through the tread can be repaired if they are not too large but punctures to the sidewall should not be repaired Tires must be removed from the rim to be properly inspected before being plugged and patched Tire Fundamentals Federal law requires tire manufacturers to place standardization information on the sidewall of all tires This information identifies and describes the fundamental characteristics of the tire and also provides a tire identification number for safety standard certification and in case of a recall Tire Label Information P The P indicates the tire is for passenger vehicles NOTE Passenger car tires are not recommended for use on trailers Chapter 10 Tire Safety Information 67 Chapter 10 Tire Safety Information 68 LT LT indicates the tire is for light trucks NOTE Light truck tires are not recommended for use on trailers ST ST is an indication the tire is for trailer use only Rajim Sim dimmir l code Malo of heighi fe i ekpa algi hieronai width of _ ipeni ipm Mina in climate
153. to traffic behind and slow down well in advance Chapter 2 Towing and Leveling 17 Chapter 2 Towing and Levling Due to slower speeds cars can become trapped behind you on a two lane road It is courteous and practical to signal and pull onto the shoulder when possible allowing them to pass This reduces passing hazards and saves tempers Auto Leveling Put a small round bubble level inside the refrigerator to determine proper level for refrigerator operation Slide Outs In extended use situations it is advisable to add support blocks under the slide room Do not raise the room Just touch the bottom AWARNING Br fare amd wehicis na tor haran pa pospe Ezxc n w PE in Pa raar ol ai L ean rel im bono wlay eer braig Consul ihe inter Cam a bAa for Tend anmi WR ie Pures Regop 1r leu Lor eel Gober Ps ured a OF beim ween bor irae rora 20 bihan ithe nmd ADH of bot weedigh for Hh whens ARO Cah anor yeh bo maintain Dropar ban of Do ot ded G Total weight retire or Che Pie dele wareniphi PRP a a thn tribe ee bra ehiall 18 Mud and Sand Let the momentum of the tow vehicle and trailer carry you through Apply power gently and stay in the tracks of the previous vehicle If stuck tow the trailer and tow vehicle out together without unhitching Parking Whenever possible avoid parking on a grade with a recreational vehicle in tow If it is necessary turn the fron
154. tor Adjustments and repairs require specialized training and tools Contact a qualified Propane Service Technician Failure to follow these instructions could result in a fire explosion and or injuries including loss of life 35 Chapter 5 Propane Gas System 36 hair spray cleaners adhesives alcohol etc Be sure to air out the trailer thoroughly after delivery and when using these products The Propane gas leak detector has a self check circuit which runs at all times while receiving 12 Volt power In the event that the circuitry fails a failure alarm will sound and the operating indicator will cease to light When To fest Detector Testing of the detector is recommended every week if power is interrupted or before each camping trip The Propane detector must be operating for at least 60 seconds before it can be tested When the Alarm Sounds Open all doors and major windows Turn off the gas supply at the Propane tank Do Not re enter until alarm stops sounding Turn on gas supply If alarm sounds a second time turn the gas off and contact an authorized dealer or Propane service technician Chapter 6 Plumbing System A recreational vehicle plumbing system consists of two sub systems The fresh water system and the wastewater system Portable fresh water is supplied by either the fresh water tank aboard the unit or from an outside source connected through the city water connection When usin
155. ture deterioration and or yellowing of the surface finish Chapter 8 Care amp Maintenance Notes 57 Chapter 8 Care amp Maintenance Maintenance Notes Maintenance Performed 58 Chapter 8 Care amp Maintenance Each Each 3 6 Each As ltem Trip Mo Mo Mo Year Req Procedures Fiberglass Exterior Wash with warm water and mild detergent Wax with liquid or paste wax Roof and Roof Inspect and re seal as needed Components Lubricate roof vent mechanism wight oil amp clean completely Windows and Doors Check vinyl seals when washing exterior X Check seals for damage and repair as needed xX Lubricate door hinges amp step components with WD40 Adjust amp lubricate window latches w powdered graphite or light oil Lube door locks amp strike pocket incl ext storage amp access doors Seals and Adhesives and Adhesives Seals and Adhesives x EE E Inspect and reseal as necessary LP Gas System Check for leaks and road damage Have qualified serviceman check pressures amp complete system Check hoses fittings and connections for leaks and signs of wear Check drainage system for leaks and road damage Sanitize system Winterize system depending on local seasonal conditions Check GFC circuits Perform maint on generator as outlined in generator manual Check and service batteries Remove food and ice from refrigerator after each trip Clean fan blades and wash filter
156. ty and to keep your carbon monoxide alarm in good working order follow the steps below e Verify the unit alarm lights and battery operation by pushing the Test button weekly Vacuum the CO alarm cover with a soft brush attachment once a month to remove accumulated dust Instruct children never to play with the CO alarm Warn children of the dangers of carbon monoxide poisoning Never use detergents or solvents to clean the carbon monoxide alarm Avoid spraying paint hair spray air fresheners or other aerosols near the CO detector Do Not paint the CO detector Paint will seal the vents and interfere with the sensor ability to detect CO Do not place near a diaper pail Test the alarm operation after your coach has been in storage before each trip and at least once a week during the camping season Chapter 4 Electrical System The electrical system in recreational vehicles is a combination 12 Volt DC Direct Current and 120 Volt AC Alternating Current system Every facet of the electrical system is carefully engineered and installed to comply with the American National Standard A119 2 and the National Electric Code To understand this system simply put the 12 Volt system is what an automotive uses and the 120 Volt system is what most households use 1e Volt System DC The 12 Volt system can be powered in three different ways a separate RV battery the converter changing 120V AC to 12V DC or
157. u apply clockwise pressure to the lug nut both needles will show the current amount of torque being applied 3 When you reach your desired torque value stop applying pressure and your indicator needle will stay at the highest torque value reached Setting Torgue Value of Adjustable Dial Wrench 1 Unlock the handle and set the dial to your desired torque value 2 Lock the handle back in place 3 As you apply clockwise pressure to the lug nut you will hear and audible click when the desired torque wrench value is reached Do not apply further pressure once you hear the click Always remember Check lug nut torque before every trip Redwood RV recommends this maintenance procedure to ensure proper torque has been applied to lug nuts before heading out on the road Lug nuts should be torqued to 110 120 ft Wheel Reinstallation Follow up Always follow 50 60 foba 140 150 fils the appropriate star h 55 60 fibs pattern as indicated on F 90 100 iris the Gh TO 120 Hikes previous page or in your heiii e a tl Re torque after first owner s manual to assure proper 10 miles 25 miles 50 miles torque Pre Trip Procedure 1 Set your torque wrench to 110 120 ft lbs 2 Begin with the appropriate bolt for your wheel 12 o clock position for 8 and 6 hole wheels and 2 o clock position for 5 hole wheels as illustrated and apply torque to all lug nuts following the star pattern indicated
158. ued is an important responsibility that trailer owners and users need to be familiar with and practice Inadequate and or inappropriate wheel nut torque tightness is a major reason that lug nuts loosen in service Loose lug nuts can rapidly lead to a wheel separation with potentially serious safety consequences see page 53 Appliances and Equipment The appliances stove refrigerator outdoor grills etc and equipment hot water heater furnace generator etc typically operate on propane gas Propane gas is flammable and is contained under high pressure Improper use may result in a fire and or explosion Be sure to follow all instructions and warnings in this manual see page 26 29 as well as the specific owners manuals of the appliances and equipment Tire Safety Properly maintained tires improve the steering stopping traction and load carrying capability of your vehicle Underinflated tires and overloaded vehicles are a major cause of tire failure For more information on tire safety please see page 61 CHAPTER 1 WARRANTY INFORMA TION Owner s Responsibilities As the owner of a new recreational vehicle you are responsible for regular care and proper maintenance as described in the Care and Maintenance section of this manual Proper maintenance will help avoid situations where the Limited Warranty does not cover items due to neglect Maintenance services should also be performed in accordance with the corresponding manu
159. ult the individual detector s user manual for specific instructions and or audible warning meanings Chapter 3 Appliances and Equipment 25 Chapter 3 Appliances and Equipment Never use wire brushes or any metallic item for cleaning range ports or orifice as wire brushes or metallic items may shed leading to a fire or explosion Never use the range or oven for extra comfort heating Cooking appliances are not directly vented to the outside as are the furnace air conditioning systems 26 odor still present after 5 minutes DO NOT relight burners See What to do if you smell gas To turn burner s off turn the knob s to the OFF position The Range or Cook top installed is a Propane gas appliance Carefully read the manufacturer s manual for complete operational and safety instructions provided in the unit packet prior to using the appliance Operation Oven if equipped Oven pilot must be lit prior to operating Lighting Oven Pilot Be sure all valves and oven control knob are in the OFF position Assure the main gas supply is on Open oven door and smell for gas If odor present Stop and Do not try to light any appliance Extinguish any open flames including cigarettes Do Not Touch Any Electric Switch Open windows and doors Exit trailer Shut off the gas supply at the gas container bottle or source Immediately call a service center or gas supplier fr
160. umulations of empty containers and debris Chapter 11 Ramp Trailers 71 Chapter 11 Ramp Trailers 72 These are all hazards which can all be present at the same time within a very confined area You need to be aware of these potential hazards when loading unloading and rigging your cargo Your continuous attention to safety measures will help prevent accidents and possibly serious injuries and property damage The biggest reason to put a priority on loading safety is not so much related to the frequency of accidents as it is to the potential severity of injuries that can occur in these types of accidents The kinds of injuries sustained when a load tips over or falls from the ramp s or falls out of the trailer or those that occur if the load shifts unexpectedly during travel tend to be very serious and sometimes fatal You can prevent these types of accidents by paying attention to what you are doing and thinking through the consequences of poor loading Poor hazard assessment decisions are directly responsible for many accidents You can help minimize these risks avoid hazards and enjoy your recreational activities safely by using an effective decision making strategy Look around you and your situation Get a good idea of what s going on around you before you act Identify hazards or specific problems in your path Equipment materials debris other vehicles children pets or any number of other thi
161. ure to which a tire may be inflated MAXIMUM LOADED VEHICLE WEIGHT The sum of curb weight accessory weight vehicle capacity weight and production options weight MEASURING RIM The rim on which a tire is fitted for physical dimension requirements NET CARRYING CAPACITY NCC Maximum weight without exceeding the GVWR Also referred to as Payload Capacity NON PNEUMATIC RIM A mechanical device which when a non pneumatic tire assembly incorporates a wheel supports the tire and attaches either integrally or separably to the wheel center member and upon which the tire is attached NON PNEUMATIC SPARE TIRE ASSEMBLY Anon pneumatic tire assembly intended for temporary use in place of one of the pneumatic tires and rims that are fitted to a passenger car in compliance with the requirements of this standard NON PNEUMATIC TIRE A mechanical device which transmits either directly or through a wheel or wheel center member the vertical load and tractive forces from the roadway to the vehicle generates the tractive forces that provide the directional control of the vehicle and does not rely on the containment of any gas or fluid for providing those functions NON PNEUMATIC TIRE ASSEMBLY A non pneumatic tire alone or in combination with a wheel or wheel center member which can be mounted on a vehicle NORMAL OCCUPANT WEIGHT This means 68 kilograms 150 Ibs times the number of occupants specified in the second column of Tab
162. use towing instability possibly causing the trailer to overturn Securely block all cargo not just wheeled equipment and round or oddly shaped items Block items separately and on all four sides using wood blocks thick enough to prevent cargo movement Use tie downs and D rings carabiners strong enough to secure the load Avoid using other cargo as a block Cargo Placement and Restraint Cargo that is likely to roll vehicles tool chests barrels etc should be restrained by chocks blocks wedges a cradle or other equivalent means to prevent rolling Whatever you use to prevent rolling should not be able to be accidentally unfastened or loosened while the trailer is in motion Proper Use of Tiedowns Avoid using tiedowns and securing devices with knows Be sure to attach and secure each tiedown so that it can t come loose unfastened opened or released while the trailer is in motion Also use edge protection whenever a tiedown could be damaged or cut at the point where it touches an article of cargo Avoid using bungee cords on D rings Tiedown Minimum Working Load Limit The working load limit of a tiedown associated connector or attachment mechanism is the lowest working load limit of any of its components including any tensioner device or the working load limit of the anchor points to which it is attached whichever is less When you choose tiedown hardware choose items that are strong enough to hold the load you are securi
163. ves etc in a readily accessible place Don t bury these items beneath other cargo When you have properly loaded your trailer with the things you need for your trip make a diagram that outlines where things are stored With this diagram your list of items and the weight of items you will be able to find specific items easily and have a handy reference for determining proper weights Weigh your trailer after you have loaded it You may have to do this several times to get it right Check the trailer tires frequently Tires can lose air over a period of time In fact tires can lose 1 to 3 PSI per month This is because molecules of Chapter 10 Tire Safety Information Keep tires properly inflated A tire that is run long distances or at high speeds while seriously under inflated will overheat to the point where the tire may lose air suddenly and or catch fire possibly resulting in damage to the vehicle and its contents and or personal injury 63 Chapter 10 Tire Safety Information Tire load ratings are dependent on tire inflation pressures Under inflated tires can be damaged and result in a loss of inflation pressure The air pressure recommended on the tire information placard is the original standard equipment tires only Your trailer my be equipped with optional sized tires Always follow the pressure recommendations stamped in the tire sidewall for any replacement tire All tires on
164. w redwoocd rv com All shipping or towing expenses incurred in transport in this manual for yearly ing the recreational vehicle for warranty service shall be the owner s inspection sheet and service responsibility certification Upon requesting warranty service you will be asked to provide the Redwood vehicle identification number VIN date of purchase and detailed list of repairs needed It is important to call ahead to schedule an appointment Mondays and Fridays are generally the busiest times at a dealer s service center as well as days before and after a national holiday Your dealer and Redwood RV want you to be satisfied with all repairs made to your unit After repairs are completed inspect them thoroughly Check off your list and review each repair with the service center representative Once satisfied sign the dealer s repair order or warranty claim form In the event a problem should reoccur after you have left the dealership contact the repair center as soon as possible so that the situation can be resolved expediently Please note your Redwood RV Company Limited Warranty covers warrantable repairs that are performed by an authorized Redwood RV Company dealer at their service center or facility only It is important for the owner to know that if you are unable to bring your unit in for repairs Redwood RV Company is not responsible for any costs incurred for the service call charge or time accrued to come out t
165. xtremely important to level the trailer front and rear using the landing gear Using the crank for the particular stabilizer jack lower the jack s on the lowest side of the trailer first and check the level Adjust if necessary and then lower the other jack s to finish stabilizing the trailer Chapter 3 Appliances and Equipment What to do if you smell gas Do not try to light any appliance Extinguish any open flames including cigarettes Do Not Touch Any Electric Switch Open windows and doors Exit trailer Shut off the gas supply at the gas container bottle or source Immediately call a service center or gas supplier from an outside phone and follow their instructions Do not turn on the gas supply until the gas leaks have been repaired Refer to the individual manufacturer s owner s manual for operating instructions on the following equipment Air Conditioner 30 Amp Only Roof mounted air conditioners are operated by an 110V AC power source through a separate circuit breaker Keep in mind that typically RV electrical systems are designed to handle 30 amps and that the air conditioner takes a sizable portion of that when the compressor starts Limited product models have an optional 50 Amp capability See Chapter 5 Electrical Systems Reduce other loads as much as possible when using air conditioning to reduce the chance of overload and possibly tripping the main breaker For thermostat operation on the air conditioner
166. y Damage to the pump and or a blown circuit may occur 3 Chapter 6 Plumbing System 38 About Vibration While Traveling Although the fresh water system was thoroughly inspected for leaks before delivery fittings can loosen over time from vibration during travel Periodically check the fittings at the faucets and visible connections and tighten when necessary Water Heater The Water Heater installed is a Propane gas appliance Carefully read the manufacturer s manual for complete operational and safety instructions provided in the unit packet prior to using the appliance The water heater installed is typically a 6 gallon standard 10 gallon or 16 gallon optional on some units Dependent upon the model installed the water heater will operate only on gas or on upon either gas or AC current For specific water heater operating instructions please consult the user s manual located in the unit packet Prior to operating the water heater be sure there is water in the fresh water tank and in the water heater Care and Maintenance Proper maintenance of the water heater relies on inspection and awareness Full maintenance requirements are listed within the manufacturer s user s manual located in the unit packet An anode rod within the tank increases the life of the tank and under normal use will deteriorate Replacement of the anode rod should be done yearly or more frequently if water supplies c
167. your trailer should be the same type size construction and load rating do not mix bias belted and radial tires air under pressure migrate through rubber from the inside to the outside A drop in tire pressure could cause the tire to become overloaded leading to excessive heat build up If a trailer tire is under inflated even for a short period of time the tire could suffer internal damage A flat can go unnoticed on a multiple axle trailer white it is being towed Running with a flat tire can cause it to catch fire and burn up your rig With a flat tire as the other tires are supporting the weight of the rig and the flat tire is less noticeable A quick check can be made by thumping each tire with a tire iron or rod to make sure they all sound the same Each time you gas up walk around the trailer and give a quick check by feeling each tire with your hand A tire that is getting low will be hotter than the rest There is no substitute however for actually measuring tire pressures to make sure they are all within safe limits Always check the cold tire inflation pressures before each trip and at least once a week during the trip for proper inflation levels The most common causes of tire failure are overloading and underinflation Both result in excess flexing of the sidewall which can cause heat buildup and eventual tire failure Continuing to run with a flat can cause it to catch fire The most importan

Redwood RV Owner`s Guide

Contents

Download Pdf Manuals

Related Search

Related Contents