N1 Video Encoder
Contents
1. is upgraded during he aircraft firmware upgrade It is recommended to keep the upgrade package files on your USB flash drive after the firmware upgrade Upgrade the fi 1 Power off a the Intelligent Flight Batteries rmware of an extra Intelligent Flight Battery as follows 2 Insert the battery that needs the firmware upgrade into the battery compartment connected to the flight controller 3 Power on the Intelligent Flight Battery in the battery compartment The upgrade will start automatically AN Remove the propellers before upgrading the firmware to avoid injuries DO NOT touch the motors during the firmware upgrade DO NOT DO NOT T start the motors while upgrading the firmware T use the N1 Assistant while upgrading the firmware Only USB flash drives formatted with FAT32 or exFAT file systems are supported Ensure that there is only one firmware upgrade package on your USB flash drive The remote controller may become unlinked from the aircraft after the firmware upgrade Re link the remote controller and aircraft if necessary Appendix Status LED Blinking Patterns Blinking Pattern Description R Solid Red No video input GQ Solid Green Video input detected BUG wee Bli Give Blinking Green Bluse Blinking Red nking Red and Green Alternatively Upgrading firmware Firmware upgrade successful Firmware upgrade failed 2015 DJI All Righ2. level and that there is at least 100MB of free space on your USB flash drive 2 Prepare the Firmware Upgrade Package 1 Download the firmware upgrade package from the DJI Developer website https developer dji com matrice 100 downloads 2 Insert your USB flash drive into your PC Extract all the downloaded files to the root directory While the M100 is powered off remove the USB flash drive from your PC and connect it to the upgrade port of the N1 Video Encoder using the upgrade cable 6 2015 DJI All Rights Reservec 3 Upgrade the Aircraft 1 Ensure the remote controller is powered off and then power on the aircraft The firmware upgrade will begin automatically once the aircraft is powered on NI Video Encoder User Manual 2 The Status LED will blink red and green alternatively to indicate that the upgrade is in progress It will take approximately 12 minutes to comp ete the firmware upgrade 3 The Status LED will blink green if the upgrade is successful at which point you should restart th generate that the upgrade is successful 4 If the Sta Upgrading the Intelligent Flight Battery Firmware The Intelligen e aircraft Check the upgrade result by openi d in the root directory of your storage device 1 us LED blinks red the upgrade is unsuccessfu ng the txt file that is automatically The text result Success indicates Run the firmware upgrade again Flight Battery firmware
3. NI Video Encoder User Manual 2015 8 chj Disclaimer Thank you for purchasing the N1 Video Encoder Users must comply with local radio transmission laws and regulations when using this product By using this product you hereby agree to this disclaimer and signify that you understand all points completely Please use this product in strict accordance with the manual and be sure to pay attention to the warnings When assembling and using this product follow all instructions carefully SZ DJI TECHNOLOGY CO LTD and its affiliated companies assume no liability for damage s or injuries incurred directly or indirectly from improper use of this product DJI is the registered trademark of SZ DJI TECHNOLOGY CO LTD abbreviated as DJI Names of products brands etc appearing in this manual are trademarks or registered trademarks of their respective owner companies This product and manual are copyrighted by DJI with all rights reserved No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of DJI This disclaimer is produced in various languages In the event of divergence among different versions the Chinese version shall prevail when the product in question is purchased in Mainland China and the English version shall prevail when the product in question is purchased in any other region Product Profile The N1 Video Encoder is intended for the DJI Matrice 100 abbr
4. ator and then detach it from the upper plate gently to avoid damaging the cable A Handle the indicator cable gently Aircraft Status Indicator 2 Remove the 16 screws M2 5x5 on the upper plate of the center frame and the eight screws M2 5x8 on the mounting rails Then remove the mounting rails and the upper plate M2 5x8 M2 5x5 4 2015 DJI All Rights Reserved NI Video Encoder User Manual 3 Connect one end of the N1 Video Encoder s video and power cables to their corresponding 10 pin or 8 pin port on the N1 Flight Controller Flight Controller ta LI a 10 pin Port OK mfo r 8 pin Port Be o A OC 4 Place the other end of the power and video cables near the mounting position of the N1 Video Encoder 5 Re mount the upper plate of the center frame and tighten the 16 screws M2 5x5 Orientate the upper plate so that the notch faces the left of the aircraft with its tail facing you Then place the mounting rails and tighten the 8 screws M2 5x8 Refer to the figure in step 2 for the screw positions e Aircraft s Tail 6 Re mount the Aircraft Status Indicator and tighten the two screws M3x8 self tapping Do not overtighten the screws to avoid damaging th
5. e threads Aircraft Status Indicator N1 Video Encoder User Manual 7 Connect the other end of the power and video cables to the power and video ports of the N1 Video Encoder C gt H all 00 ag aire e laH ra l Power IN lo i i O Video OUT o LDN ENST S AN The N1 Video Encoder only supports the DJI N1 Flight Controller Please strictly follow the steps above to supply power to the device 8 Use foam tape to mount the N1 Video Encoder to the expansion bay gimbal mounting plate or other flat surfaces Usage Video Encoding 1 Turn on the remote controller and then the Intelligent Flight Battery Connect your mobile device to the remote controller and turn on your camera 2 Connect your camera to the N1 Video Encoder through the HDMI or AV port The two video ports cannot transmit together See the Appendix for the pinout diagram of the AV port 3 Launch the DJI GO app and enter Camer View A live camera preview on the screen indicates that the N1 Video Encoder is working normally 0 If both the HDMI and the AV ports are connected the HDMI signal will take priority Firmware Upgrade Upgrading the Aicraft Firmware 1 Check the Battery Level and Storage Device Ensure that the Intelligent Flight Battery has at least 50 battery
6. eviated as M100 and DJI N1 Flight Controller for which it offers video signal transmission and firmware upgrade capabilities if you are not using the Zenmuse X3 Gimbal with Camera as your recording device The AV or HDMI port on the encoder receives video input from the non DJI camera to generate a live HD video feed in the DJI GO app In addition users may utilise the Micro USB port on the encoder to upgrade the firmware of various modules on the M100 In the Box N1 Video Encoder x1 AV Cable x1 Upgrade Cable x1 t G Power Cable x1 Video Cable x1 Reserved Cable x1 Overview Status LED HDMI IN Micro USB Upgrade Port Reserved Port Video OUT Power IN i Ine if VIDEO OUT POWERIN A DO NOT connect the power cable to the reserved port This will cause serious damage to both the flight controller and the N1 Video Encoder The video and power cables are delicate parts Handle with care SA 2015 DJI All Rights Ri N1 Video Encoder User Manual You will require a 2 0mm hex key and foam tape to install the N1 Video Encoder onto the M100 If you are using HDMI IN prepare an HDMI cable If you are using AV IN prepare a soldering iron some solder and heat shrink tubing for wiring Installation 1 Remove the two screws M3x8 self tapping on the Aircraft Status Indic
7. ts Reservec 7 N1 Video Encoder User Manual Supported Video Inputs Source Video Formats AV PAL NTSC HDMI 720p50 720p60 1080i50 1080i60 1080p25 1080p30 1080p50 1080p60 Specificaitions Dimensions 65 2 mm x 45 mm x 10 7 mm Weight 31 49 Operating Temperature 10 to 40 C Pinout Diagrams AV Port 1 GND 2 AV IN 3 GND Reserved Port This content is subject to change Download the latest version from https developer dji com matrice 100 If you have any questions about this document please contact DJI by sending a message to DocSupport dji com 2015 DJI All Rights Reserved
Download Pdf Manuals
Related Search