1400 1401 Chlorinator User Manual
Contents
1. After the 24 hour period or if the salt is at the required level turn the cell switch to on and the pump switch to manua auto or RECOMMENDED LEVELS TO ENSURE OPTIMAL OPERATION Pool chemistry should be tested at least once a week during summer months Salt Level 4000ppm 6000ppm by weight with 5000ppm being ideal never below 4000ppm All Ramzonics models are over salt protected and can run with levels higher than 6000ppm ie sea water Free Chlorine 1 5ppm 3 0ppm depending on the time of day and period of time since the chlorinator has been running Adjust by altering the chlorine output level or the operating hours If levels have become too low manual super chlorination may be required pH and Total Alkalinity A pH of 7 2 to 7 6 and a total alkalinity of 80ppm 120ppm unless advised otherwise by your pool professional Fibreglass pool suppliers usually recommend a pH of 6 9 to 7 2 To lower the pH and total alkalinity add hydrochloric acid To raise the pH and total alkalinity add sodium bicarbonate These levels may not be achievable with some water supplies Stabiliser 40 80ppm pool stabiliser also called cyanuric acid helps the chlorine produced to last longer Without it in your water your chlorinator will need to run longer than it otherwise would Hardness 100 to 250 ppm Levels higher than the recommended level will result in a less efficient cell in regards to its chlorine production2. a more frequent need for cleaning and a chance the cell will fail prematurely To minimise chances of high hardness levels minimise or avoid the use of chemicals containing calcium especially Calcium Hardness and calcium based granular chlorine Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 6 of 11 Installation Location The unit should be installed in a sheltered location away from direct water spray and sunlight Usually in the pump enclosure The unit weighs 13kG and is balanced about its centre The centre screw of the supplied J bracket must be screwed minimum 50mm into a timber stud or masonry with a suitable anchor The outer screws are to prevent tipping The top rear lip of the cabinet hooks onto the J bracket Maximum external ambient temperature is 60C Starting up Once correctly installed and ensuring the minimum level of salt has been achieved switch the chlorinator on at the main power supply Position the pump switch to man and once the pump has fully primed position the cell switch to on The chlorine output indicator on your Ramzonics can be used to check the pool salt level Turn the chlorine output control clockwise to the maximum setting 100 If this cannot be achieved check pool water for low salt level Set your daily operating time as per instructions below and set the chlorine
3. claim if in its opinion the claim cannot be justified If the repair is to be carried out outside the manufacturer or its authorised service agents a service fee is applicable It is the customer s responsibility for the cost of freight both ways in all other circumstances This service fee cost is available on request from the manufacturer or its agents 17 No warranty is applicable without proof of purchase 18 This warranty is applicable to workmanship and materials only The manufacturer will replace at no charge all parts returned freight paid which display faulty workmanship or materials The manufacturer accepts no responsibility for loss damage or injuries to person or property arising from warranty failure of equipment or installation of that equipment Except with the authority of the manufacturer any replacement shall be provided only by the manufacturer or its authorised distributors and this warranty shall not extend to any expenditure otherwise incurred Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 11 of 11 Products This document refers to Chlorinator manufactured saltwater chlorinators Model 1400 20Amp and 1401 30Amp Product Description Saltwater Chlorinator This product is a transformer isolated Extra Low voltage phase controlled DC reversing chlorinator power supply for use with a suitable saltwater chlorina
4. output indicator at 80 100 Test the free chlorine level in the pool water after 24 48 hours adjusting the chlorine output to the desired level depending on your pools requirement It is recommended your Chlorinator should be set to generate a free chlorine level of 1ppm to 3ppm Daily Operating Time The required chlorinator operating time varies throughout the year Long periods of hot weather require longer chlorinator operation time because the higher water temperature and increased sunlight break the chlorine produced by your Chlorinator down more quickly To be sure that your Chlorinator is being run for long enough check your pool chlorine level regularly If the chlorine reading is low turn the chlorine output dial up clockwise and or run the chlorinator and pool pump for longer If the chlorine reading is high turn the chlorine output dial down anticlockwise or reduce the chlorinator and pool pump operating time It is recommended that your Chlorinator is run for a few hours in the evening and a few hours in the morning Super chlorination can be achieved by running your Chlorinator overnight This practice is recommended about once per fortnight during summer Setting the Timer Select the operating hours by pressing the actuators inwards towards the centre on the timer in order for the timer to run for the corresponding time ica The timer in the picture is set to run from 8 11am 12 noon 3pm 4 8pm NAT i UL P red s
5. RAMZONICS Saltwater Chlorinator Page 1 of 11 RAMZONICS Manufactured Chlorinator Owner s Manual Model 1400 20A Reversing Self Clean Model 1401 30A ReversingRamzonics Self Clean Usg Ao CIRS CIRCUIT BREAKER PUMP MUM SALT CC NTENT 0 4 4 O00PPM IDEAL F 4 BREWS 6 000PPM M or IN 80 100 z l MENT NOT AL SALT C _ J Vo Mode aa Sn AMP ae lt a 7 4 k EY i WARNING This equipment must be installed and serviced by a qualified technician Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 2 of 11 Improper installation can create electrical hazards which could result in property damage serious injury or death Improper installation will void the warranty Table of Contents Table of Contents CMO ALOR OWE SV a A aensaeaeuen sca tontaadese E 1 WAI Ol COM COIS ee E E E E E A EA 2 Ramzonics Salt Water CHIOrinators ccccccsssccccsssecccenscccaeneccseaeeeceseuscesseeeeeseacesseuecesseneeessaecesseaecesssauseesaaesessaeeeees 3 Chorme CIS CY OU osica e S caunacaee S E ua dostentasacannneavacos ace Gusaasanstesuquaeeeaneatenmeentaneeee 3 BSS SiO cect arson sre EE ears E EA E vane E apres ean EAE AE E N onnsiansamene nanan AE E OE 3 TE POWE PACK Enea E a E E S E A E 4 The Electrolytic 1 Osa eep emcee tein sean eave pun sasanemeusnsauescess samsancee aneo nn NEN Nan eas euermcanadar mer seuamenceecnyaie
6. ber not to neglect routine testing through the winter e Do not add salt through the skimmer box only add directly in to pool water e When cleaning the cell see below only use cell cleaner obtainable from your local pool shop Never use hydrochloric acid or any instrument like a screwdriver to scrape contamination off the cell Cleaning the Cell Your Chlorinator cell operates only efficiently when it is clean To check your cell for cleanliness disconnect the mains power supply unscrew the nut at the top of the cell housing and remove the cell electrode A dirty electrode will have visible deposits of calcium and other matter built up Model 1400 amp 1401 are Reversing models and must be used with cells designed for automatic reversing Under normal conditions this will automatically clean deposits off the cell though other factors like high calcium hardness levels in your water could result in the occasional need for a manual clean To clean your cell after removing it from the housing immerse in cell cleaner liquid obtainable from your local pool shop for five to 10 minutes until the cell appears clean Agitating the cell while immersed will soeed up the process the less time the cell is spent in the liquid the better Rinse with fresh cold water before reassembling the cell into the housing When regularly cleaning the cell it is essential to use on the fastening ring nut and the cell o ring a silicone based lubricant each t
7. ection Set the time of day by turning the outer ring of the dial T e clockwise until the correct current time is set against the marker the timer in the picture to the right is set at 9am Note 24 hour time clock Actual timer may vary 14 50 SA rA ON litrli HL i iad EE o Harpen A o N q 2 A KOS 7 7 XN N 17 ftti ti L TA tte ee Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 7 of 11 Maintenance Looking after your Chlorinator Power Pack There are no user serviceable parts inside the unit Do not carry out any maintenance or repair work other than that shown in this operating manual or as advised by Ramzonics and only use parts recommended by Ramzonics Incorrect parts and adjustments will breach warranty e Do not store pool chemicals in a confined space with your Chlorinator The fumes will corrode amp damage internal parts e Small insects can also enter cooling vents causing damage to vital components To avoid this happening routinely spray insect repellent to the surfaces around the power pack No Water Flow Salt cells contain a sensor that checks for proper water flow and for safety purposes if adequate water flow is not sensed your Chlorinator will cease to produce chlorine until the problem is resolved If this situation occurs the chlorine ou
8. ell Your Chlorinator cell must be plumbed last in the pool pipework after all other pool equipment just before the return to the pool ensuring the cell can be removed For maximum efficiency your cell should be installed with the water entering the cell housing at the end closest to the cell lead see image below Ensure that the cell is positioned horizontally so that the gas bubbles formed by the cell will be trapped in the cell housing when the pump is turned off If you are in any doubt about the gas trap requirements please contact your retailer or Pool Ranger Australia The cell lead must be connected to the junction box under the power pack Connect blue to blue brown to brown and black to black Be sure to replace the junction box cover Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 5 of 11 Chemical Maintenance Initial preparation Ensure minimum salt level of 4000ppm If the pool is new to saltwater acquire ideal salt level of 5000ppm by adding 50kg per 10 000 litres a standard 50 000 litre pool would require 250 kg salt at start up If salt level needs to be risen after adding required salt super chlorinate pool with liquid chlorine or sodium dichloride raise chlorine level to 3 4ppm Turn the chlorinator cell to off and turn pump switch to manual to start filtration system for a minimum period of 24 hours
9. ime the cell is cleaned This ensures that no leakage occurs from the cell housing Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 9 of 11 IN THE EVENT OF PRODUCT FAILURE PLEASE CONTACT Ramzonics OR ITS AGENTS FOR SERVICE DETAILS Warranty Checklist BEFORE you contact your agent or Ramzonics for a warranty claim please ensure you consider the following points 1 Have you filled out your warranty registration 2 Do you know what the warranty covers The Power Pack 2 year conditional warranty The Electrolytic Cell 2 year conditional warranty plus 36 month pro rata at RRP 3 Have you correctly tested your pool water for salt level Your nearest pool shop should be able to do this test for you Ideal range for your Chlorinator is 5000 ppm 6000 ppm Never below 4000 ppm 4 Have you cleaned your cell as per the manufacturer s instructions 5 Have you read and understood the Chlorinator operating manual 6 Is your Chlorinator correctly installed as per the directions in the operating manual 7 Do you have a copy of the receipt from either the pool builder or retailer where you purchased the Chlorinator 8 Pro rata warranty pricing is based on the recommended retail price at time of claim Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chl
10. orinator Page 10 of 11 Warranty Your Chlorinator is manufactured to the highest standards employing the latest technologies and carries the following warranty should a fault occur due to faulty manufacture or materials IMPORTANT Two year conditional manufacturer s warranty which covers faulty manufacture or material This warranty covers DOMESTIC USE ONLY Warranty does not cover 24hr and Commercial installations such as public pools hotels schools health clubs hospitals etc Warranty for this type of use is 12 months only Should a fault covered by warranty occur the purchaser must in the first instance contact the supplier of the Ramzonics product a Service Agent or Ramzonics direct Ramzonics warrant the original purchaser of the Chlorinator Power Pack for a period of 24 months from the DATE OF PURCHASE This warranty only applies to failure caused by faulty manufacture or materials Ramzonics also warrants the original purchaser of the Ramzonics electrolytic cell against faults caused through manufacture or materials for a period of 24 months from the DATE OF PURCHASE Ramzonics also warrant the electrolytic cell for a further 36 months to be repaired or replaced at a monthly pro rata price from the DATE OF PURCHASE at the Recommended Retail Price The warranty ts void if the following are deemed to apply or have not been adhered to 1 The cell not being cleaned regularly Refer to page 6 of this manual This does not apply to the
11. secaeederaeeneracnecaeved 4 Chemical IU INCE seraiki o AN EN EO aO EEO E NOSE 5 INitial preparation sinerien ornini r ron E a a E AEE EAEAN EES E a ED EE 5 Seli E EE EEE TAIE T PTEN IE EENE A TEN OA IAE E A A ATE E E AEE TT 5 ECCONE aE E T E E E E E 5 pand TOLARA oaren E E EEA 5 SEO WIS A E A T E TEE N E E E E A A E A T A E E E 5 FRCPC SS coc a ess ten garam de pounce ein ect pont ene oe anna ie oe eines annonce ee tquneeeeeceeuaness 5 metalai O enaere ENEAN E EA E warunescaserateraencettereenecanawenanmatestooss 6 AE O ea EN R E E A E A A 6 Daily Operating MEM Seta cca cess ceicreccin na Ea a mea ea E oes nwa araueevas 6 Oe CEU iV UW T eea E E E E EEE AEE N AE EAER 6 IV TEI ELIT CO sessir r AA EA AAAA Error Bookmark not defined Looking after YOUr Ramzonics Power PACK wecsaccisscecanssceassaieanccusatsnpoansbcncntcepsanstaseiusnaeusenstadeavemeuns i aa aa aa 7 ING VY a FION o E E A E A E E E N anes 7 See Or POOL OPE ONG o E R E E E E E E E E O 7 Looking after your cell oes cas aera caesar seaeaasuaenseussaconeuesanpeacaaaouseqnmeaeaamenceussanmaeusssssseasaineqnetaeiaaeaceuanvarsagenstueencsseeaceeerss 8 Seg aes a8 gt ee nn ne ee O A E 8 Warrenty CHECKISE ci ccsosateacisnedesessassaiinnsateasisusdina iE N Ea AE 9 WV Ir SIVELY E EEEE A ENE E A I E E E E Error Bookmark not defined POO a E E E 11 Produ DESIDE oroa A EE R A 11 DIRENE eee A A EE A a E E E E aliases 11 ET E cet E A E A E A E E E T E E E EE E T AE E E A S 11 The unit complies
12. self cleaning model 2 A cell blocked or damaged with calcium causes the cell to fail prematurely and is not covered by this warranty This does not apply to the self cleaning model 3 Damage to the electrolytic cell resulting from a Matters beyond manufacturer s control b The cell or power pack are installed incorrectly by any person other than a person authorised to do so by the manufacturer or its agents 4 The power pack must not be connected to a power supply other than 240 volt 50 Hz Never plug more than one pool pump into your Chlorinator 5 Water above the temperature of 45 degrees Celsius must not flow through the cell 6 Water must flow freely through the cell when turned on 7 The chlorinator must not be serviced by any other person other than the person authorised by Ramzonics 8 The cell must never be cleaned other than with a recommended cell cleaner Never use concentrated acid 9 Running the chlorinator in less than 4000ppm salt in your pool will destroy the anode coating voiding warranty 10 Damage during freight 11 Noncompliance with installation instructions 12 Damage by foreign objects ie insects 13 Damage caused by chemicals being stored directly under or near the power pack 14 Acts of God ie storms lightning strikes floods etc 15 Warranty does not cover unauthorised alterations modifications or work carried out by unauthorised technicians 16 The manufacturer reserves the right to refuse a warranty
13. ting cell Dimensions 360x200x200mm Weight Model 1400 20A Nominal 5Kg Model 1401 30A Nominal 8Kg The unit complies with standards AS NZS 3100 2009 General construction amp insulation AS NZS 3136 2001 Swimming pool equipment AS NZS 311 2009 Circuit Breakers AS NZS 61558 2 6 Isolating Transformers AS NZS 3123 Connectors AS NZS 3191 Flexible Cords AS NZS 3190 RCD Installation AS 60529 IP Standard IP34 Splash resistant Input Power Rating Complete unit including attached pool pump 230VAC 10 at 10A maximum Chlorinator Part Number 1400 20A 230VAC 10 at 225VA Part Number 1401 30A 230VAC 10 at 265VA Pool Pump Motor 3 4HP 500VA Output Power Rating Cell 6VDC Reversing at 20A 30A maximum dependant on Salt content Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930
14. to the cell and the Salt Cell where the chlorine is produced Power Adjustment 4A Breaker Pump Power manual Off Timer Power Output Mains On Off 24 hour Timer FRONT VIEW Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 4 of 11 Cell Junction Box cover removed Pool Pump 240V Outlet Bottom View mains Cord The Power Pack Your Chlorinator unit is weather protected to an IP34 rating splash Resistant The power pack should be mounted with the wall bracket a minimum of 1 metre above ground level maintaining a rear wall clearance of at least 1cm and side top and bottom clearance or minimum 150mm located so that the cell power lead can reach the junction box It should be installed in a well ventilated position ensuring that pool chemicals especially acid are not stored in the direct vicinity as the fumes may damage vital components Plug the 3 pin power plug of your Chlorinator into a suitable 240 volt A C power supply For safety the power point should be connected through a Residual Current Breaker installed to AS NZS 3190 Plug the 3 pin power plug of your filter pump into the 240 volt A C power point on the underside of your Chlorinator Please ensure that only the one filter pump is plugged into the socket Maximum Switchable power is 3 4HP The Electrolytic C
15. tput indicator will drop to zero and the No Flow LED will light until the flow is returned Settings for Pool Operations The following is a guide to setting your Chlorinator to perform various pool operations OPERATION 240V SUPPLY CELL SWITCH PUMP SWITCH Run pump amp chlorinator via timer ON CONC AUTO Run pump amp chlorinator manually PON ON MAN Vacuum or backwash PON FF MAN Clean cell or cartridge filter When turning cell switch to the off position for backwashing cleaning cartridge or cleaning the cell REMEMBER to turn cell back to the on position when resuming normal filtration operation Similarly if you have turned any valves to the closed position to clean the cell or the cartridge filter remember to turn them back to the open position before resuming water flow Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 8 of 11 Looking after your cell Your cell is a delicate piece of equipment and needs to be maintained correctly There are several key points that need to be followed to avoid premature failure of your cell e Ensure your pool water is correctly chemically balanced with a pH of 7 2 7 6 a total alkalinity level of 80 120ppm and a calcium hardness level of 100 250ppm e Never operate with salt levels below 4000ppm paying particular attention after high rainfall periods and remem
16. with standards ssnnesssseessseeressseerosssrerssssrrerossrrresssreresssersssreresssrerossereresssreeressereeessreres 11 HPO POWER Ram VE en E E E E E 11 Output Power Rating ssessssssessesssessesressroseesrrsrroseosresressresreesessresresrroseoseereeseoseesreoreesroseesreesreereeseoseesreereeseeree 11 Australian Made by Ramzonics Pty Ltd 2 12 Mitchell Rd Moorebank NSW 2170 PH 02 9824 1199 Mob 0433 405 930 RAMZONICS Saltwater Chlorinator Page 3 of 11 Ramzonics Salt Water Chlorinators The RAMZONICS range of chlorinators will automatically maintain the chlorine level of your pool and eliminate problems associated with periods of very high or low chlorine levels Fewer fluctuations in chlorine levels mean fewer fluctuations in pH levels This adds up to more stable balanced water Consistently maintained sanitizer levels in the pool water will prevent the growth of all common algae A salt water chlorinated pool requires much less attention than a chlorine pool Chlorine Generation A small amount of natural salt is dissolved into the pool water As the pool water flows through the electrolytic cell electrolysis separates the salt water into its basic components sodium and chloride Pure chlorine gas is produced by this process and goes to work in the pool Following this process the chloride and sodium re bond and become natural salt again Description The package consists of the chlorinator power pack to supply power
Download Pdf Manuals
Related Search