CFO331/521 user manual
Contents
1. CCL CCL output input 24V 1A The screw terminal connector and CCL connection Contact Closure loop CCL connection The CFO331 521 link provides one bi directional contact closure channel line CPT lt gt CRR The CCL input is a normal short circuit on off signal between connector s contact pins CC in and CC in signal ground The CCL output is a normal relay on off signal 24V 1A between connector s contact pins CC out and CC out The connector in use is a screw terminal connector The CCL output channel can be alternatively configured for VSA Video Source Alarm usage with DIP switch The default factory setting is VSA off Screw terminal connector s CC pinout Video Source Alarm VSA The CCL output channel can be alternatively configured for Video Source Alarm VSA monitoring Instead of normal CCL use the CCL output can be used to provide a VSA signal if a loss of video signal occurs When VSA mode is enabled at transmitter and if video signal is missing e g a camera malfunction link otherwise operates normally the CCL output pins are closed Using VSA at just one end of the link enables the opposite path to be used for standard CCL operation simplex In case when VSA is enabled both at transmitter and receiver the CCL channel is no longer available for any other use When VSA is disabled the CCL channel is available for normal use in both directions The VSA mod2. data mode The desired data connection must be confirm by the means of DIP switches IC RS485 2w RS485 4w wa I oa ma a Daas ote EB TE Screw terminal connector s data pinout DIP switch position Rs om on of ay te E ran om om Rsassaw J o Jo daja linebias f fJ on on TT nolinebias J oof oag q Too tema FO BEE HE BE notem oof FoF o o S ysa oo do O O l o Data connection settings SW2 Note If data cabling is requiring signal ground the CC IN terminal can be used for this purpose The desired data mode settings including dwelltime settings for RS485 2w can be set by the means of DIP switches The default factory setting is RS485 2w dwelltime 75 us no line bias and no term RS485 2w Dwelltime settings Data channel EIS ee ee eee moa o on on on on on o 002 of on o on of on ER on on on f o o on on CC on f ot 0 RS485 4w Left side view SW1 SW2 Data mode Data connection selection settings naa SW1 SW2 Bottom view ARANDA 666005 Be CRR331 521 DIP switches SW1 amp SW2 8 CFO331 521 video link user manual CG TEC CG CC DATA DATA DATA BATA OUT OUT IN IN OUT OUT bs IN rn output input 24V 1A I CCL CCL The screw terminal connector and CCL connection CFO331 521 video link user manual Contact Closure loop CCL connection The CFO331 521 link prov
3. is 1 Vpp Video connection is equipped with the dual colour VIDEO led on the front panel See next page for explanation of VIDEO indicator led s lights 2 CFO331 521 video link user manual Data connection The CFO331 521 link provides one bi directional data channel CPT lt gt CRR The connector in use is a screw terminal connector Available data modes for data channel are RS232 RS422 RS485 2w and RS485 4w See table below how to connect the desired data mode The desired data connection must be confirm by the means of DIP switches The desired data mode settings for data channel can be set by the means of receiver s DIP switches see page 7 for detailed description The default factory setting is RS485 2w dwelltime 75 us no line bias and no term ene Cons Spin Screw terminal connector s data pinout AAADOR DIP switch position ata contact YOULL tie fs fe fs 8 CPT331 521 DIP switches Rs232 o o a nn oe nn ar ur a Transmitter data channel mode must set en i Rs485 2w J on on Rsa85 4w ot l mebias o on no fine bias o oof A ic ee ee ee no term IC Sa AO IO DE EHE CR Data connection settings AC AC ee AC O O Y NN DC DC TOO SS Note If data cabling is requiring signal ground the CC IN terminal can be used for this purpose CFO331 521 video link user manual 3 AC AC RSO o N IS DC DC oJ fo U NN IS
4. I LNO LNO viva viva viva viva 09 29 329 29 NI LNO NI C unk status The permitted supply voltage range is 10 5 14 VDC The current consumption is 250 mA The permitted operational temperature range for CRR331 521 is from 34 to 74 C gt Video connection and indicator led The impedance of the video connection BNC female is 75 Q The nominal input output level is 1 Vpp Video connection is equipped with CRR5 1 the dual colour VIDEO led on the front panel See table below for OPTICAL explanation of VIDEO indicator led s lights RECEIVER CRR331 521 Optical Receiver 1 Locking screw 2 pcs 2 Video output BNC female and video indicator led 3 Data amp CC connector screw terminal 10 pin 4 Optical input output SC PC and link status indicator led 5 Handle with unit information See further information on dedicated sections 6 CFO331 521 video link user manual OUT OUT IN IN GG Ge us ne DATA DATA DATA NE OUT OUT IN OUT OUT IN The screw terminal connector containing data and contact closure connections HR CRR331 521 Data connection DIP switches SW2 CFO331 521 video link user manual Data connection The CFO331 521 link provides one bi directional data channel CPT lt gt CRR The connector in use is a screw terminal connector Available data modes for data channel are RS232 RS422 RS485 2w and RS485 4w See table below how to connect the desired
5. NITS USES CLASS 1M LASER DIODE DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS APPLICABLE STANDARD 1EC60825 1 2001 side view The CPT331 521 is a one channel optical transmitter for uni directional video transmission with one bi directional data and one contact closure channel The current consumption is max 250 mA 12V DC CPT521 Stand alone installation CPT331 521 Optical Transmitter 1 Optical input output SC PC The CPT331 521 units are designed for stand alone installation The unit jy kink status Indicator led should be mounted with a help of wall bracket to a installation place 3 Video indicator led 4 Screw terminal connector 10 pin The supply voltage can be either 12V DC or 24V AC The supply 5 Video input BNC female voltage is provided by either a surveillance camera unit or by an external mains adapter The permitted supply voltage range are 10 5 14 VDC and 16 28 VAC In DC use the 12V DC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS251 The permitted operational temperature range for See further information on CPT331 521 is from 34 to 74 C dedicated sections 6 DIP switches for data connection selection 7 Grounding Wall bracket dimensions Video connection and indicator led The impedance of the video connection BNC female is 75 Q The nominal input level
6. User manual CFO331 521 one channel video link CFO First Mile series consist of fibre optic modems which provide a high quality and losless video transmission for variety of CCTV applications m ae vr ir TIA Ty ano TN Ino aM A Fu m ae u un LITO ELFO FLO io 959 95 55 39 u viWO VIVO VINO YiVO 39 35 99 00 PS Li ah Hl ing Ino CRR521 OPTICAL RECEIVER Mi Hl ine Wh SNLVLS YNI Video Networks CFO331 521 video link user manual 59300260 rev005 Contents GEO331 521 one channel video linkS ci er a ee ee dc 1 A u et 1 EEND E a BERNER O HEERES REN ARE RERBENTARE NE 1 CPT Mini sized stand alone video transmitter z4 s0240 0 0nan 00ER nun an nun nn nun nun an nun an nun an nnn nn nun nn nn nun an nun an nnn nennen 2 GENE O A en See ee A EE ATE AT A 2 stand alone Install atom sc das 2 Video connection and indicator led 422224444444R BR ER ann en nennen nennen anne nennen nenn nn nn nn ann nn nn anne nenne nennen nennen 2 Data COMME CONN is a a ee RT Be a aes an A Bence ene see 3 Contact Closure loop CCL CONME CHONG en ee een ae 4 video Source Alarmi VSA exter arta a E es 4 Link status indicator EA A ne n rnrn nAn E EARE nee ei een ern enet 5 FOC OCC OM oaia a dao 5 CRR S3Ingle channeloptical receiver iaa ee 6 A A 6 Frame installation an e nen A 6 stand aloneinstallationzscesain sunshine oon aa denen e
7. e can be set on off by the means of DIP switch see previous page Note Video detection circuitry has 20 sec delay before VSA alarm is activated inactivated 7 Video missing VSA CCL OUT PINS CLOSED CPT331 521 CRR331 521 VSA OFF VSA ON CCL OUT CCL IN VSA CCL OUT PINS CLOSED CPT331 521 CRR331 521 VSA ON VSA OFF CCL IN CCL OUT CCL and VSA connection examples CFO331 521 video link user manual Link status indicator led The CPT331 521 contains LINK STATUS indicator led on the front panel which inform generic status of unit Optical signal level is adequate and synchronization on link level is achieved Optical signal level is adequate but no synchronization on link level is achieved Optical signal is missing or input level is too low LINK STATUS indicator operation Fibre connection The optical connector is of the type SC PC The optical output level is constant and cannot be adjusted For optical specifications please see page 11 When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system front view Note For correct optical operation ensure that all optical connectors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed air or other equivalent pressurised gas The optical connec
8. g centre In advanced video network systems the CFO331 521 offers a flexible way for first mile transfer to the nearest collection point of a larger scale network The CPT331 521 stand alone transmitters are capable of using both 12 VDC or 24 VAC supply voltage CPT331 521 unit is a compact size housing for special stand alone installations requiring minimal installation space Also as an optional DIN rail mounting is possible item code CIK001 All CRR331 521 units are compatible with all CFO rack systems Stand alone options are available with the CMA015 module adapter and separared CPS series mains adapter As with all CFO platform products these specific models do meet all typical EMC as well as other environmental and manufacturing related requirements e High performance uncompressed zero delay digital video transmis sion SNR 67 GB typical 10 bit video sampling e One CVBS PAL NTSC video channel e One bi directional data interface compatible with EIA232 422 485 e Data rate up to 230 kbps e One bi directional contact closure e Transmission on one multimode fibre up to 5 km CFO331 e Transmission on one singlemode fibre up to 40 km CFO521 e Units for rack mount or stand alone installations e Mechanically compact and ruggedised e Transmitter unit available in a special small size stand alone design CPT CFO331 521 video link user manual 1 CPT Mini sized stand alone video transmitter CAUTION THESE OPTICAL U
9. ides one bi directional contact closure channel line CPT lt gt CRR The CCL input is a normal short circuit on off signal between connector s contact pins CC in and CC in signal ground The CCL output is a normal relay on off signal 24V 1A between connector s contact pins CC out and CC out The connector in use is a screw terminal connector The CCL output channel can be alternatively configured for VSA Video Source Alarm usage with DIP switch The default factory setting is VSA off EEE aa Contact closure input ground Contact closure input Contact closure output relay Contact closure output relay Screw terminal connector s CC pinout Video Source Alarm VSA The CCL output channel can be alternatively configured for Video Source Alarm VSA monitoring Instead of normal CCL use the CCL output can be used to provide a VSA signal if a loss of video signal occurs When VSA mode is enabled at transmitter and if video signal is missing e g a camera malfunction link otherwise operates normally the CCL output pins are closed Using VSA at just one end of the link enables the opposite path to be used for standard CCL operation simplex In case when VSA is enabled both at transmitter and receiver the CCL channel is no longer available for any other use When VSA is disabled the CCL channel is available for normal use in both directions The VSA mode can be set on off by the means of DIP sw
10. itch see previous page Note Video detection circuitry has 20 sec delay before VSA alarm is activated inactivated 7 Video missing VSA CCL OUT PINS CLOSED CPT331 521 CRR331 521 VSA OFF VSA ON CCL OUT CCL IN VSA CCL OUT PINS CLOSED CPT331 521 CRR331 521 VSA ON VSA OFF CCL IN CCL OUT CCL and VSA connection examples front view IT i BOMH The optical connector type is SC PC 10 Link status indicator led The CRR331 521 contains LINK STATUS indicator led on the front panel which inform generic status of unit Optical signal level is adequate and synchronization on link Green level is achieved Blinking Optical signal level is adequate but no synchronization on Yellow Green link level is achieved Optical signal is missing or input level is too low LINK STATUS indicator operation Alarm connection Alarm at the rear connector of the unit is low open collector output with the capability of 30 V 10 mA switching No synchronization achieved at Link status alarm 2 optical input Open collector alarms Fibre connection The optical connector is of the type SC PC The optical output level is constant and cannot be adjusted For optical specifications please see page 11 When installing the fibre optic cable do not exceed the minimum bending radius when connecting cable to the system Note For correct optical operation ensure
11. larms Ed keyboard oo switch 11 Copyright acknowledgements Information in this document is subject to change without notice and does not represent a commitment on the part of Teleste Corporation Copyright Teleste Corporation All Rights Reserved No part of this document may be reproduced transmitted stored in a retrieval system or translated into any other language without the express permission of Teleste Corporation Teleste Corporation Video Networks P O Box 323 FIN 20101 Turku FINLAND www teleste com WEEE directive Directive 2002 96 EC of the European Parliament and of the Council on waste electrical and electronic equipment WEEE obliges that producers appropriately mark electrical and electronic equipment with the symbol indicating separate collection This obligation applies to the equipment put on the market in EU after 13 August 2005 Teleste devices which belong to the scope of the directive have been marked with the separate collection symbol shown below The marking is according to the standard EN 50419 The symbol indicates that the device has to be collected and treated separately from unsorted municipal waste User manual revision history note The latest version is always available in pdf format on our web site www teleste com CFO331 521 video link user manual CFO331 521 video link user manual 13 TELESTE www teleste com
12. s 6 Video connection and indicator Al ne ee 6 BALACON WO eres ee E a Me A A T Contact Closure loop CCL connection 02224202220000000nn nenne nnnnnennnnnnnnnnnnnnnnnne nenne nnnnnnn nenne nnnnnensnnnnennnnnnnnnn 9 Vdeo SONCE Alarm VISA ar ee era need 9 EINK STALUS INGICATOF isa ia ee 10 AA HON ee ee el ee 10 A A ee E ee TE Ro ee 10 Technical SPeciicatoOn Sii a 11 CFO331 521 video link user manual CFO331 521 one channel video links CFO331 521 singlemode 1 channel video link for uni directional video and bi directional data and contact closure transmission for variety of CCTV applications D C Welcome and thank you for purchasing Teleste s CFO Products x1 x1 C gt General These one channel video link units offer a 10 bit video transmission with one bi directional data and one contact closure channel over one singlemode fibre CFO521 or over one multimode fibre CFO331 PAL NTSC and CVBS video formats are supported to provide a transparent video transmission All common data protocols are supported as well and are easily configured by DIP switches Optical transmission is based on class 1M laser operation The multiplexed data stream of 202 5 Mbps enables a full quality and a real time video transmission in one multimode fibre up to 5 km CFO331 singlemode fiber up to 40 km CFO521 typical transmission distance The primary application is a point to point transmission from camera to monitorin
13. that all optical connectors are cleaned immediately before mating Connectors should always be cleaned using high purity alcohol e g methyl or isopropyl alcohol Dry the surfaces using clean compressed air or other equivalent pressurised gas The optical connectors on the equipment should always be protected with dustcaps when there is no fibre inserted Note Video data and CCL outputs are disabled until optic link is properly established Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges CFO331 521 video link user manual Technical Specifications Optical Optical transmitter CPT Output wavelength 1310 nm 50 nm Output power 14 8 dBm Input sensitivity 31 dBm min Bit rate 202 5 Mbps Optical connector type SC PC Optical receiver CRR Output wavelength 1550 nm 50 nm Output power 14 8 dBm Input sensitivity 31 dBm min Bit rate 40 5 Mbps Optical connector type SC PC Transmission distance max 5 km CPT CRR MMF 40 km CPT CRR SMF EN 60825 1 FDA 21 CRF 1040 10 amp 1040 11 Note The actual maximum distance may vary depending upon which multimode cable type is in use Led laser classification Video Number of channels 1 uni directional Standard PAL NTSC CVBS Input level 1 Vpp Input overload le
14. tors on the equipment should always be protected with dustcaps when there is no fibre inserted Note Video data and CCL outputs are disabled until optic link is properly established Optical connection meets class 1M laser safety requirements of IEC 60825 1 2001 and US department of health services 21 CFR 1040 10 and 1040 11 1990 when operated within the specified temperature power supply and duty cycle ranges The optical connector type is SC PC CFO331 521 video link user manual 5 CRR Single channel optical receiver The CRR331 521 is a one channel optical receiver for uni directional video transmission with one bi directional data and one contact closure channel The current consumption is max 250 mA 12V DC Frame installation The CRR331 521 module is to be pushed along the guide rails into the installation frame e g CSR216 or 316 series and secured with the two locking screws The unit can be freely positioned in any slot in the frame The empty positions in the frame should be blanked off with cover plates The supply voltage is to be provided by a CPS384 or CPS390 power supply unit which are installed back of frame Stand alone installation The unit can be installed for stand alone use by using a CMA015 module adapter The module should be mounted to a vertical surface The 12 VDC supply voltage is supplied by the means of a separate mains adapter with a regulated output e g CPS251 1no NI N
15. vel 1 75 Vpp Impedance 75 ohm Sampling resolution 10 bit Sampling rate 13 5 MHz Bandwidth 5 5 MHz 1 dB Insertion gain 1 dB C L gain inequality 4 C L delay inequality 40 ns Differential gain 2 Differential phase 1 SNR 67 dB weighted Video connector BNC female Data Number of channels 1 bi directional Data format RS232 422 485 selectable Data rate 0 230 kbps Sampling rate 16 MHz Data connector Screw terminal CPT331 Video Data Cc CPT521 multimode OM1 fibre singlemode fibre Contact Closure Number of channels Input Output Switching frequency Contact closure connector Alarms Video Optical input signal General Supply voltage Supply voltage connector Current consumption Dimensions H x W x D CRR CPT Weight Video amp link status Operating temperature Storage temperature Humidity EMC compatibility 1 dry contact 24V 1A relay 5 Hz Screw terminal CC output B alarm 10 5 14 VDC 16 28 VAC screw terminal 250 mA 3U 5HP 190 mm 35 48 62 mm 0 2 kg 0 5 kg LED displays 34 74 C 40 80 C 0 95 bi directional max configurable CRR regulated CPT CPT max without CMA without connectors CPT CRR recommended non condensing EN61000 6 3 EN50130 4 CE Typical values unless otherwise stated optical CFO331 521 video link user manual fibre Video CRR331 ae Alarms CRR521 bate A
Download Pdf Manuals
Related Search