CW1210V Owner`s Manual
Contents
1. Page 5 Installation Sheet STEP 3 Final Installation Check List Instructions and other items have been removed from the tub Shipping bolts have been removed Washer dryer is plugged in to an electric outlet and is properly grounded Water hose is connected to the faucet with inlet screens and washers Water is turned on and checked for leaks at faucet and machine end connections Drain hose is properly located into drain facility and is not collapsed or damaged Washer dryer has been properly levelled all legs firmly on the floor and lock nuts engaged Water fills properly Test for proper operation by running the washer dryer through a complete cycle Test Run 1 Prepare your laundry 2 Select fabric type and Wash cycle Program Refer to fabric care label for instructions 3 Load cotton laundry into the drum Load no more than 6 Ibs of laundry Do not over load Load unit approximately 2 3 visually full with similar fabrics Load detergent in dispenser 2 for main wash Follow detergent guide Use low sudsing detergent Turn Wash Program knob to select the desired wash cycle Press the desired buttons Press dry time button to start drying Press Start Verify washer dryer is filling with water 10 Verify washer dryer stops filling 11 Verify drum is turning and the cycle is ON 12 Verify unit rinses during the rinse cycle 13 Verify unit2. water you need extra detergent to get your clothes clean With soft water you need less detergent Too much detergent can be harmful potentially causing serious problems with your washer dryer For this reason it is always best to find out your water hardness and adjust your detergent usage Keep your detergent fresh Under the sink isn t a good place to store detergent Too much moisture will cause the powder to cake If your powder detergent gets older or lumpy throw it away It won t wash well Old detergent often won t dissolve If you use a liquid detergent these precautions are not necessary because liquid detergents don t lump as they age or come in contact with water You will find four compartments in your Washer Dryer dispenser Pre wash Wash Softener Bleach Front load machines need much less detergent than top load washing machines Follow detergent manufacturer instructions for front load machines Detergent is flushed automatically into the drum from the detergent dis penser Over sudsing will cause your unit to malfunction Suds may rise through detergent dis penser and may spill on your floor so be very care ful in choosing the detergent quantity based on laundry load fabric type and soil stain conditions Always choose a low sud detergent for this machine Bleach Recommendation Always dilute bleach before using Excessive Frequent use of bleach can damage clothes Bleachin
3. and two scoops or caps of detergent Pour this into detergent drawer compartment two Choose automatic wash program rotate Wash program knob to position four Rotate water Temperature knob to 140 F position Push Power button to start Repeat if necessary To remove hard water deposits or scales use washer safe labeled cleaners Wipe drum thoroughly with a damp cloth Apply a liquid nonflammable household cleaner to stained areas and wipe with a soft cloth to remove stains or colors Never use steel wool Use descaling agents suitable for use on stainless steel Some descalers contain chemical components that can attack parts of your washer dryer Be careful in selecting the right descaler After cleaning run a cycle with plain water to remove any residual agents before inserting laundry Water I nlet Hose Replace hose after five years of use to reduce risk of hose failure Periodically inspect and replace if bulges kinks cuts wear or leaks are found Mark the date of replacement on the hose with a permanent marker Lint Filter A To avoid water spills during removal of lint filter place a bowl or tray under filter assembly The lint filter is located at the bottom right corner Always run the unit on spin mode before removing the lint filter to drain away residual water Place a bowl or tray under the lint filter area to catch any residual water We recommend this strongly to avoid water spills on your floor Open the bottom panel Uns
4. correctly e Is your drain hose fixed at the correct height i e Is the power cord plugged into a 110V power receptacle water is flowing e At the start of the cycle water inflow is low and is absorbed by the laundry quickly This creates a perception that water is not flowing This is normal allow the program and the cycle to continue Drum does not fill but e Is power cord plugged into a 110V power receptacle Washer dryer stops e Are all knobs correctly rotated Do they point to the program e Is water inlet hose blocked or kinked Is the tap on e Is there electrical power at the wall receptacle e Call an electrician to check the wall socket e Are you using an extension cord Do not use an extension cord e Is the drum overloaded with laundry e Is the lint filter clogged Do not open while unit is full of water e Is the drain hose clogged Is the end of drain hose more than Washer won t drain 2 63 ft above the floor e Is the lint filter clogged Do not open while unit is full of water e See installation instructions for proper installation of drain hose e Is the door open e Are there excessive suds e Is your voltage low Check your electrical service or call an electrician Do not use an extension cord j a 7 oO v gt ct e a E 2 oO e Is the end of the drain hose more than 2 63 ft above the floor e Is there a air gap in the drain hose e Is the lint filter clogged
5. model is not designed for use on 50 Hz AC electrical service We do not recommend conversion For Technical Assistance or if your washer dryer requires service replacement parts or accessories contact Technical Services and Support toll free at 1 866 517 7827 Page 8 HOW TO USE YOUR WASHER DRYER C Making It Easy For You Wash Program Knob Use this knob to select wash program of your choices Always turn knob clockwise To choose a program align the colored mark on the knob to the program number or text Dryer Timer Knob Allows you to preset drying time Based on your needs to make your laundry damp dry or dry Refer to Drying table for details This is a Timer not a Thermostat Wash Temperature Knob Allows you to choose desired Temperature setting for water during the Wash cycle Refer to clothing care label for guidance Lamp Lights up when power is turned ON Goes away when power is turned OFF Power Button Push to turn power ON Push again to turn OFF Keep button at OFF position for the door to open at the end of the cycle Door will not open if this button is kept at ON position Door Handle 110 V 60Hz No Spin Button Push button to skip spin cycle Do not press this button in automatic mode or the dryer will not turn Use this button for delicate fabrics only Refer to clothing label instructions Super Rinse Button Allows you to do a Super Rinse at full load or turns ON the Intellig
6. Do not open while unit is full of water e Are all knobs correctly positioned e Is the unit plugged into a 110V power receptacle e Is voltage low Check electrical service or call an electrician Washer continues to fill or drain or the cycle seems stuck e Are shipping bolts and spacers removed Washer makes noise e Are gears engaging These are normal washer dryer noises e Coins or safety pins or other metal items may be in the drum e Heavy wash loads can produce a thumping sound This is normal e Is the Washer Dryer levelled Are all four feet resting firmly on the floor e Adjust leveling legs if necessary e Is your flooring correct Refer page 8 Page 19 Troubleshooting Guide PROBLEM Washer Dryer leaks Detergent dispenser clogged Load too wet Residue or lint on load Stains after wash Load is wrinkled Page 20 POSSI BLE CAUSE AND REMEDY e Is water inlet hose tight Are all hose washers properly seated e Is the drain hose clamped and properly installed e Is the sink or drain clogged e Was too much detergent used Excessive suds will cause the unit to overflow e Is the unit leveled and resting firmly on the floor e Check leveling and adjust Check household plumbing for leaks e Check filter cap is closed tightly Is trim in place e Check detergent dispenser for clogs e Did you use excessive detergent Is the detergent low sudsing Always measure and use low sudsing detergents Pour
7. ONLY NO SPIN OO QOece Wash Program Temperature Dryer Timer No Spin Start WASH ONLY RINSE HOLD OO Oece Wash Program Temperature Dryer Timer Rinse Hold Start WASH ONLY SUPER RINSE OO Oece Wash Program Temperature Dryer Timer Super Rinse Start Select fabric type and program Turn wash program knob to the program number on the dial Turn temperature knob to select desired heat setting Turn dryer knob to select time in minutes Press spin button to select 550 rpm or release for 1200 rpm Push start button This program allows wash through dry automatically When drying is complete drum stops turning Press stop button open door and take away laundry The cool down feature towards the end of drying cycle prevents creases amp wrinkles Choose the dry settings to fold and put away your clothes immediately In this program drying capacity must not exceed 6 Ibs Select fabric type and program Turn wash program knob to the program number required Turn temperature number to the desired heat setting Turn dryer knob to off position Press start button Turn wash program knob to dry cycle position Turn dryer knob to select time in minutes Press Spin button to select 550 rpm or release for 1200 rpm Press start button Refer drying table to determine the correct time Alwais remember that time to dry varies by dampness and fabric type Your dryer is constructed to deliver dry laundry that can be folded and put away imm
8. R DRYER 1 Place the drain hose in the drain Do not allow the hose to kink or get damaged 2 Do not install the drain hose into the drain in an air tight connection ensure there is some airflow possible 3 For best performance the drain hose should not be restricted in any way 4 The drain stand pipe should be not be higher than 2 6 ft and not lower than 1 64 ft 5 Caution must be exercised to avoid collapsing or damaging the drain hose 6 Strap the drain hose to the stand pipe 7 Thread the inlet water hose to your cold water faucet connection Tighten by hand until snug Turn an additional 2 3rd turn by pliers 8 Do not OVERTI GHTEN Make sure the water line connection into the back of the unit is secure 9 Turn on the cold water supply Check all connections for leaks 10 Plug the power cord into a grounded 110V 60Hz approved electrical service protected by a 10 amp fuse or a comparable circuit breaker The washer dryer is grounded through the third prong G refer to page 7 11 Slide washer dryer into position Make sure the drain hose remains routed straight through the clip without collapsing or kinking 12 Level washer dryer by turning the leveling legs in or out as necessary 13 Tighten leg lock nuts 14 The washer dryer must be level on four sides To properly level use a carpenters level It is always a good idea to check for level again after the first few washes and re level if necessary J aYS uoejjezsu
9. Use and Care Guide COMBI NADA LAVADORA SECADORA COMBI NE LAVE LI NGE SECHE LI NGE WEdgeStar sses co Contents Appliance Registration 2 Care amp Cleaning 14 Model and Serial Numbers 2 Vacation amp Winter Storage 15 Safety Instructions 3 Safety Features 16 Installation Instructions 4 7 Fabric Care Symbols 17 18 Water and Electrical Requirements 8 Troubleshooting Guide 19 21 Operating Guide 9 10 Warranty Backcover yele pelecten liela Technical Services and Support Detergent Guide 13 Call canter For service call 1 866 517 7827 Model CW1210V 461305722 CENE LEC UL HARMONIZED Help us Help You Before using your washer dryer read this book carefully It is intended to help you properly operate and maintain your new washer dryer Keep it handy for answers to your questions If you don t understand something or need technical assistance please contact Technical Service and Support 101 3rd Street Kentwood LA 70444 Phone 1 866 517 7827 Write down the model and serial numbers You will find them on a label fastened at the rear of the unit Before using your washer dryer please write these numbers here Model Number Serial Number If you received a damaged washer dryer Immediately contact the delivery company dealer or the builder from which the unit was purchased Damage is not covered under the manufacturers warranty Save Time and Money Before you request s
10. able or explosive substances this could lead to vapors that could ignite or explode e Make sure that Dry cleaning solvents gasoline flammable or explosive substances are not added or get mixed with the wash water These substances give off vapors that could ignite or explosive e If your washer dryer has not been used for 2 weeks or more there is a possibility of hydrogen gas being formed as in any closed hot water system Make sure that you turn on the water supply system and let the machine run and drain for a few times This will flush out the accumulated gas if any In the interest of safety please do not use an open flame and do not smoke during this time near the machine Hydrogen gas is flammable e Do not allow children to play near the machine e Do nor reach into or attempt to open the machine while the drum is moving eDo not tamper with controls e Do not repair replace or attempt to any form of sevicing unless otherwise recommended in our user manual or carry out any instructions that you have not understood and not have skills to carry out Always leave servicing to qualified personnel Call 1 866 517 7827 for service needs e Remove the door of your washer dryer before removing from service or discarded e Do not use softeners or such forms of products to eliminate static unless recommended by the clothing manufacturer or by the softener manufacturer e Do not dry items containing foam rubber textured materials el
11. and usage conditions This warranty applies to the purchase and use of this product in residential settings within the United States of America WHAT IS NOT COVERED The following limitations apply to the coverage of this warranty Optional accessories attachments and appearance items are excluded from warranty coverage as is shipping damage and any damage caused by improper voltage or any other misuse including abnormal service handling or usage This warranty does not cover normal wear and tear on parts or replacement of parts designed to be replaced e g filters etc This warranty does not cover service trips to deliver pick up repair or install the product or to instruct in proper usage of the product Damages or operating problems resulting from abuse operation outside environmental specifications uses contrary to instructions provided in the owner s manual accidents vermin fire flood improper installation unauthorized service acts of God or unauthorized installation or modification are excluded from warranty coverage This warranty does not cover labor incurred 91 days or more after the date of original purchase Note the warranty exclusions listed above if this product is used in a commercial or multi family setting Page 23 DESCRIPTION OF WARRANTY SERVICE All defective product components covered by this warranty will be repaired or replaced at EdgeStar s option free of charge on a mail in basis to E
12. bols appearing on garment labels provide care instructions from the garment manufacturer These symbols seen on the fabric serve as minimum laundering instructions to indicate washing bleaching drying ironing and dry cleaning Additional symbols or words or both may be used to clarify the instructions The water temperatures listed below are provided as a guideline Actual water temperatures obtained in the home depend on washing machine settings regional supply temperatures and water heater settings E It s time to wash new clothes that you brought last week and you don t undestand a care label yi Permanent Press Wrinkle Resistant Li Gentle Delicate p A Hand Wash ssa Water Temperature 120 F Hot Water Temperature 105 F Warm Water Temperature 85 F Cold Cool RE Warning Do Not Wring Pt Warning Do Not Wash Care information tags are available on most clothes sold in the United States These written instructions normally give a single care method for your garment When an international care symbol tag is also present all care methods will usually be shown We are happy to present the international symbol guide as a handy reference to help you select a correct wash and dry program that supports the care method prescribed by the garment manufacturer T 9 oy A O 9 Page 17 Fabric Care BLEACH A k gt DRY HHn Onan
13. crew and remove the lint filter Run water on the filter to clean away detergent or softener residue Rinse with hot water dry using a clean towel and reinsert the filter back Turn it clock wise and lock it in position We recommend cleaning after every 25 full loads It is not necessary to clean the lint filter after every load Detergent Drawer Pull the detergent drawer out Wash all compartments under running water Clean the recess with an old toothbrush Make sure all detergent accumulations are removed Use a jet of running hot water to flush out residues Replace the drawer and run a rinse cycle without laundry Page 14 Vacation amp Winter Storage B Install and store your washer dryer where it will not freeze Because some water may stay in the hoses and other parts and components freezing can damage your washer dryer If storing or moving your washer dryer during freezing weather winterize it Nonuse or Vacation care If you are going away on vacation or not using your washer dryer for an extended period of time you should e Unplug washer dryer or disconnect power e Turn off water supply This helps avoid accidental flooding due to a water pressure surge while you are away To Winterize Washer Dryer e Shut off water tap e Disconnect and drain water inlet hose e Fill all four detergent drawer compartments with RV type antifreeze Run washer dryer on Program 4 for about 30 seconds to mix an
14. dgeStar s authorized repair facility during the first 90 days from the date of original purchase All defective product components covered by this warranty will be repaired or replaced at EdgeStar s option on a mail in basis to EdgeStar s authorized repair facility during the time period beginning on the 91st day from the date of original purchase and ending one year from the date of original purchase During this time period parts will be supplied free of charge but labor charges will apply All replacement parts and units will be new remanufacturered or refurbished All products and components replaced by EdgeStar under warranty service become the property of EdgeStar Please note that the term of the warranty does not extend beyond 90 days for units used in commercial settings Please note that labor is not included for units used in a multi family setting OBTAINING WARRANTY SERVICE Contact EdgeStar for troubleshooting assistance and warranty service authorization at 1 866 517 7827 Please have your order receipt available to confirm the date of purchase Once an EdgeStar authorized representative has confirmed that your product is eligible for warranty service he or she will discuss your options for service Within the first 90 days after the date of purchase in home service will be provided free of charge within the lower 48 United States excluding units used in multi family settings Do not return defective product to th
15. e a failure in the water valve or extended fill time The inlet valve system may not shut off correctly To avoid the possibility of water damage should a hose leak always have faucets accessible Turn off faucet when washer dryer is not in use Drain Facility We recommend the height of the standpipe to be not higher than 2 63ft and not lower than 1 64 ft Make sure the drain facility is capable of accepting the drain hose in a secure manner Flooring For best performance the unit must be installed on a solidly constructed floor Wooden floors need reinforcement to minimize machine vibration Carpeting and soft tile surfaces are contributing factors in vibration and may cause the washer dryer to move slightly during the spin and dry cycles Never install the washer dryer on a raised platform or on any weak structure Proper flooring is the responsibility of the owner Location We recommend the washer dryer not be installed in areas where water may freeze or boil The washer dryer maintains some amount of water internally at all times in components like the valve the pump and in the hose areas If this water freezes it can damage belts the pump the motor hoses or other components Make sure the operating temperature is not below 60 degrees F Your washer dryer is a ventless system therefore it can be installed in a closet or in an alcove Warning Your washer dryer is manufactured for operation on 60Hz AC approved electrical service This
16. e nma oad nmi Any Bleach when needed Only non chlorine bleach when needed Warning Do Not Bleach Dry Normal Permanent Press Wrinkle Resistant Gentle Delicate Heat Setting High Heat Setting Medium Heat Setting Low Special Instructions Line Dry Hang to Dry Special Instructions Drip Dry Special Instructions Dry Flat Special Instructions Dry in Shade Warning Do Not Dry used with do not wash Warning Do Not Tumble Dry z4 Ga Warning Do Not Iron Warning No Steam DRY CLEAN O FT ft itt te Dry Clean Any Solvent Dry Clean Normal Cycle Any Solvent Except Trichloroethylene Dry Clean Normal Cycle Petroleum Solvent Only Professionally Dry clean Reduce Moisture Professionally Dry clean Short Cycle Professionally Dry clean No Steam Finishing Professionally Dry clean Low Heat Warning Do Not Dry clean Page 18 if B Questions Use This Troubleshooting Guide ef A PROBLEM POSSI BLE CAUSE AND REMEDY Washer won t fill rinse e Is power cord plugged into a 110V power receptacle or drum will not turn e Is Wash Program knob pointing to the correct program number e Is water inlet hose kinked e Is water pressure at the tap correct Is the tap ON e Is the door closed e Is the fuse blown or circuit breaker tripped e Are shipping bolts and spacers removed e Are knobs rotated clock wise e Is your Wash Program knob working
17. e place of purchase This warranty is in lieu of any other warranty express or implied including without limitation any warranty of merchantability or fitness for a particular purpose To the extent any implied warranty is required by law it is limited in duration to the express warranty period above Neither the manufacturer nor its distributors shall be liable for any incidental consequential indirect special or punitive damages of any nature including without limitation lost revenues or profits or any other damage whether based in contract tort or otherwise Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you This warranty gives you specific legal rights You may have other rights that vary from state to state Page 24
18. ediately Select fabric type and program Turn wash program knob to the program number required Turn temperature number to the desired heat setting Turn dryer knob to of position Press the No Spin button Press the Start button In this program the machine skips spin cycle It is meant for stopping the machine after rinse and drain Use this button for delicate fabrics where the clothing label does not recommend spinning Do not press No spin button in Automatic program or the dryer will not turn on Select fabric type and program Turn wash program knob to the program number required Turn temperature number to the desired heat setting Turn dryer knob to the off position Press the Rinse Hold button Press start button This program is meant for pausing the machine after rinse without draining In this program the machine stops after the last rinse with drum full of water Press stop button open the door and take out your laundry Some fabrics need to be drip dried Refer clothing label to identify such fabrics Do not press the Rinse Hold button in Automatic Program or the dryer will not turn on Select fabric type and program Turn wash program knob to the program number required Turn temperature number to the desired heat setting Turn dryer knob to the off position Press Super Rinse button Press the Start button Press stop button at the end of the cycle to remove laundry In this program the machine runs a super rinse
19. en use the dryer e Allow the unit to run from wash to dry without interruption e Check the fabric type some fabrics are drip dry only e Did you set the temperature knob correctly Excess temperature may cause the load to wrinkle j fa S 7 oO v gt ay a E 2 o Troubleshooting Guide PROBLEM POSSIBLE CAUSE AND REMEDY oadlis tangled or twisted e Did you overload drum Loads should move freely during washing e Did you place laundry loosely into the drum Do not wrap clothing together e Were sharp items removed from the pockets before washing Fabric damage e Empty pockets zip zippers snap or hook fasteners before washing e Were strings and sashes tied to prevent tangling e Were items previously damaged Mend rips amp broken threads in seams before washing e Did you overload drum Laundry should move freely during washing e Did you pour bleach directly on the laundry Did you follow clothing care label instructions e Did you overload drum Is your washer dryer draining properly e Is your laundry load too small to tumble properly Add more laundry e Is the water turned on The dryer uses cold water during the dry cycle to create the condensation process Is the unit connected to cold water Washer does not dry e Check that washer dryer is off Have you pressed Stop Wait for about three minutes e Gently hit the door to cause a vibration to release the safety device Doo
20. ent recognition system at Half load Press when your laundry load is 6 lbs or less The unit will set water level and adjust to the load intelligently Do not press at full load Rinse Hold Button Allows you to stop the wash cycle during the last rinse with the drum full of water Use this button for synthetic and wool programs only Push to activate Some fabrics need to be drip dried only to prevent wrinkling Press again stop Do not press this button in automatic model or the dryer will not turn ON Spin Push to select 550 rpm Release to select 1200 rpm Use the handle to open and close door A click sound is heard when door is closed This activates a safety device that prevents door from opening during wash dry cycles Always turn off the appliance wait for 2 3 minutes The warning light must go off before attempting to open door Do not open the door during Wash or Dry cycles This could lead to water spills and drum damage I e O x o g e o lt e c g v gt e U0 lt o Page 9 How To Operate Your Washer Dryer Good Washing starts with hot water To get your clothes clean and dry you need hot water Your washer dryer automatically heats the water in the wash cycle AUTOMATIC PROGRAM O O Wash Program Temperature Dryer Timer Spin Start WASH ONLY Wash Program Temperature Dryer Timer Start TIME DRY ONLY DDO co Wash Program Dryer Timer Spin Start WASH
21. equipped with a three prong grounded plug for use in a properly installed and grounded outlet Warning Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or servicer if you are in doubt on grounding the appliance Do not modify the plug provided with this appliance Have a qualified electrician install the plug into the wall receptacle if the plug does not fit the outlet To prevent risk or fire electric shock or personal injury all wiring and grounding must be done in accordance with National Electrical Code local codes and ordinances The owner of the appliance is responsible for providing adequate electrical service for this appliance Grounding Instructions This appliance needs a branch circuit requirement of 15 A Always install on a branch circuit protected by 20A OR 30A ratings This appliance must be grounded Grounding reduces and eliminates the risk of electric shock This appliance is fitted with a proper grounding pins Plug your washer dryer into a appropriate outlet that is installed and grounded in accordance with your state and country electrical codes Warning Improper connection without grounding can result in electric shock Check with your local qualified electrician or authorized service personnel if in doubt Water Water pressure of 30 to 120 p s i is required to correctly fill the washer dryer Pressure of less than 30 p s i may caus
22. ervice Check the trouble shooting guide Pages 19 to 21 It lists causes of minor operating problems that you can correct yourself Page 2 Energy Saving Tips The power and water consumption of your washer dryer can be minimized if you follow these suggestions Operate washer dryer only in full load When you put in a partial cotton load press the Super Rinse button This automates the cycle for energy needs If you don t need pre wash avoid using cycle 1 e Always select cycle 3 for cotton load and keep temperature at 140 Always soak or treat stains before the wash Always select the maximum rpm spin speed to reduce moisture content If you need Service To obtain service see the warranty service page in the back of this book We re proud of our service and want you to be pleased If for some reason you are not happy with the service you receive here are two steps to follow for further help FIRST contact the people who serviced your appliance Explain why you are not pleased In most cases this will solve the problem NEXT if you are still not pleased write down all the details and call 1 866 517 7827 Explain your problem A customer service representative will assist you IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance WARNING When using this appliance always exercise basic safety precautions including the following Use this appliance only for i
23. f you are using a vented machine please keep the exhaust opening and surrounding area free from dust dirt or lint at all times e If you are using a vented machine please keep the exhaust duct and the inside of the appliance clean free from dust dirt or lint Please check periodically e Always keep away cooking oils and items exposed to cooking oils from your washer dryer Contaminated items could create a chemical reaction that could possibly cause the load to catch fire The down lightning flash icon enclosed within a AN triangle is intended to warn the user that parts used inside this product risk electric shock topersons The exclamation icon within the triangle is intended to tell the user that important operating and sevicing instructions accompany this product in paper form 3 D pi g 5 rF v y R cr lt 5 WV er 4 c A mr 5 o di SAVE THESE INSTRUCTIONS i Page 3 Installation sheet Tools needed for I nstallation e Multi wrench e Utility Knife eChannel Lock eNut driver eLevel e Screw driver Flat Blade Electrical Refer to serial plate for specific electrical requirements Water Washer Dryer needs one standard 3 4 inch water supply faucet with a pressure between 30 to 120 pounds per square inch VENTED WASHER DRYER VENT PIPE CONNECTION Parts supplied for installation This washer dryer expels damp air during the drying period This damp air must be ex
24. g Whitens clothes removes problem stains deodorizes amp sanitizes Use discretely and always follow bleach manufacturer instructions Do not add bleach while rinsing Pour bleach in detergent dispenser 3 Do not overfill bleach This can damage clothes Fabric Softener Recommendation All fabrics benefit by the use of softeners We recommend use of softener to reduce the clinging effect in synthetics and make laundry feel soft Pour the softener in detergent dispenser 4 Do not overfill Excessive use of softener may affect wash results Always follow softener manufacturer instructions 1 Pre Wash 1 76 ounce Max 2 Main Wash 4 41 Ounce Max 3 Bleach 2 71 Fluid Ounce 4 Softener 2 71 Fluid Ounce Max o oO or oO Q oO gt or e 3 Q o Page 13 Care and Cleaning A Unplug electric power cord before cleaning washer dryer to avoid shock Cleaning the Exterior Use a soft damp cloth or sponge to wipe up any spills Occasionally wipe the outside of your unit to keep it looking new Cleaning the Interior The drum is made of stainless steel so it will no rust However specks of rust can be caused by small metal articles like safety pins paper clips or belt buckles washed in the washer dryer The drum should be cleaned regularly Not cleaning the drum may lead to a build up of scale clogs limescale and dirt leading to replacement Clean the drum by using chlorine bleach Mix one cup of bleach
25. hausted outside of the room where unit is installed Inlet Water Hose One To properly exhaust the air screw pipe A into base B in such Washers Two a manner that the tube is pointed upward The exhaust pipe A can not be longer than 2 meters in order to avoid reduction in dryer performance The pipe A has to be correctly fitted to the base B in order Cabinet Dimensions to avoid leakage during the washing or drying process Side View Rear View 5 g A 9 I gt Page 4 Installation sheet Proper installation is extremely important for your washer dryer to function correctly When you first receive your washer dryer remove the box and packing material from the unit and inspect it carefully If you find damage immediately contact the delivery company and the company from which the unit was purchased STEP 1 PREPARE WASHER DRYER 1 Carefully remove the box and packaging materials from the outside of the washer dryer 2 The drain hose and the power cord are secured on the back of the unit Please unstrap them 3 Unscrew and remove the four shipping bolts from the back of the washer dryer Remove the four spacers that the bolts were attached to as well Store these in a safe place in case you need to move the washer dryer in the future 4 Loosen the two front adjustable legs to the desired level and lock nuts with spanner provided STEP 2 INSTALL WASHE
26. ing detergents out of the reach of children preferably in a locked cabinet Observe all warnings on container labels to avoid personal injury e To minimize the possibility of electric shock disconnet this appliance from the power supply before attempting any maintenance e Do not reach into the appliance if the tub or drum is moving e Do not install or store this appliance where it will be exposed to extreme weather e Do not dry clothing containing rubber foam rubber or any rubber textured materials e Note Pressing the Power button does not disconnect the appliance from the power supply e We recommend having a qualified technician service your appliance e Gas is produced by the chemical action within the tub of your washer dryer It can accumulate in the tub and or water pipes if hot water is not used for two weeks or longer Some of these gases may be noxious or even combustible To prevent the possibility of damage or injury if you have not used the appliance for two weeks or more or moved moved into a residence in which the water pipes may not have been used for sometime turn on all water faucets on all water faucets and allow them to run for several minutes before using this appliance In keeping with your best interest and safety please read these carefully e Do not wash or dry clothes or any items that have been soaked in spotted with washed in or cleaned in with gasoline dry cleaning solvents or any other flamm
27. it carefully and wipe up spills e Did you pour fabric softener in the fabric softener dispenser e Did you pour bleach into its correct dispenser e Did you use a powdered bleach Use liquids only e Is your wash cycle program correct See pages 11 and 12 e Did you select 1200 rpm spin speed e Is the temperature setting correct e Did you turn your knobs correctly Do they point correctly e Did you press Rinse and Hold button Is voltage correct e Did you sort your laundry properly e Did you overload the washer dryer Lint can be trapped in the load if overloaded Wash smaller loads e Was paper or tissue left in the pockets e Did you use enough detergent Follow detergent guide e Did you set temperature correctly Cold water will not dissolve detergent completely e Did you clean lint filter e Did you follow the guide when adding detergents Refer page 13 e Use just enough detergent to remove soil and become soluble e Use correct fabric softener depending on fabric type e Is water in your tap hard Install an ion filter if possible e Did you properly sort the load Is color bleeding Mix only if color does not run e Did you leave clothes in the drum at the end of the cycle Some dyes transfer during dry cycle Make sure color does not run e Is detergent dispenser clean Clean if necessary e Is your wash cycle correct Is the drum overloaded e Did you remove clothes after the wash cycle hang dry and th
28. olors Synthetic Quick Wash Synthetic Delicate Color Wool Pre wash 3 Times Wash 3 Rinses amp Spin 1 Rinse amp Spin Final Spin 3 Times Wash 3 Rinses amp Spin 1 Rinse amp Spin Final Spin 2 Times Wash 3 Rinses amp Spin 1 Rinse amp Spin Final Spin One Wash 3 Rinses amp Spin 1 Rinse amp Spin Final Spin One Wash 3 Rinses amp Spin 1 Rinse amp Spin Final Spin Select Damp Dry Select Damp Dry Select Damp Dry Select Damp Dry Do Not Dry Page 11 Drying Options Choose your drying options from the table below to suit your personal preference Dry Damp Dr TE Synthetic amp Delicate 2 2 Ibs Page 12 Detergent Guide How to choose and use the right detergent First use only detergent specifically made for use in front load washers Other types will cause over sudsing Second use only low sudsing powder or liquid detergent Performance of this machine will be adversely effected if high suds detergents are used Third check your water hardness If your water is hard 7 grains or more your detergent has to work harder Your water department can tell you how hard your water is So can your county extension agent or your area s water softener company Just call and ask them how many grains of hardness are in your water How much detergent do you use That depends Is your water hard or soft With hard
29. on your laundry Do not press Super Rinse button in Automatic program or the dryer will not turn on Page 10 Wash Cycle Selection What happens in each cycle Wash Cycle Time Minutes Approx Wash Cycles Drying Fabric Temperature Load Condition Type oF Cycle Sequence 1 Pre wash Regular 5 Color Rapid Wash Express Cotton Whites Cotton Very Dirty Whites Cotton Jeans Cotton Resistant Colors Cotton Delicate Colors Cotton Assorted Colors Wash 12 lbs Dry 6 Ibs Wash 12 lbs Dry 6 Ibs Wash 12 lbs Dry 6 Ibs Wash 12 lbs Dry 6 Ibs Wash 12 lbs Dry 6 Ibs Wash 12 lbs Dry 6 Ibs Pre wash 4 times Wash 3 Rinses amp Spin 1 Rinse amp Spin inal Spin Times Wash Rinses amp Spin Rinse amp Spin inal Spin 3 Times Wash 3 Rinses amp Spin 1 F Rinse amp Spin inal Spin Times Wash Rinses amp Spin Rinse amp Spin inal Spin Times Wash Rinses amp Spin inse amp Spin inal Spin Wash Rinses amp Spin 1 Rinse amp Spin Final Spin ee 3 3 1 F 2 3 1 F 0 w oO 155 Select Dry or Damp Dry Select Dry or Damp Dry Select Dry or Damp Dry Select Dry or Damp Dry Select Dry or Damp Dry Select Dry or Damp Dry uo01 29 S P J YSeM 9 Pre wash 10 Regular 11 Gentle 12 Express 15 Regular Synthetic Resistant Colors 104 140 Synthetic Assorted C
30. r does not open j a S D 7 gt ay gt re fa E 2 D To receive more information call toll free 1 866 517 7827 Page 21 Notes Page 22 WARRANTY This EdgeStar product is warranted to be free from defective workmanship and materials for the first year following the date of original purchase Replacement parts will be supplied free of charge for the first year following the date of original purchase Labor will be performed free of charge for the first 90 days following the date of original purchase COMMERCIAL USE WARRANTY EXCLUSIONS If used in a commercial environment this EdgeStar product is warranted to be free from defective workmanship and materials for the 90 days following the date of original purchase Replacement parts will be supplied free of charge and labor will be performed free of charge for the 90 days following the date of original purchase MULTI FAMILY USE WARRANTY EXCLUSIONS If used in a multi family environment this EdgeStar product is warranted to be free from defective workmanship and materials for the first year following the date of original purchase Replacement parts will be supplied free of charge for the first year following the date of original purchase WHAT IS COVERED This warranty applies to the original purchaser only and only covers defects in workmanship experienced during operation of the product under normal service maintenance
31. s For the protection of your family and loved ones your washer dryer is equipped with many safety features We Care For You Child Safe Door An electromechanical safety device in the door prevents it from opening during operation Door will not open until the unit is shut down and the power button is turned off Washer Motor A thermal safety device protects the motor from overload or underload giving the motor long life Temperature A safety thermostat prevents excessive water temperature Water will not heat if the water level is inadequate water from the tap stops flowing or the tap is not turned ON The machine will not start if prescribed water level is not available Water Spills The filling valve stops if the water inlet filter is clogged or if the drain pump motor malfunctions This protects your flooring carpets and rugs from water spills Safe Areas By design access is denied to children adults reaching into the door or touching the pump motor filter while the unit is ON Fuse A safety fuse built into the unit prevents excessive electrical overload Plug Your washer dryer is equipped with a grounded plug to protect against leakage currents System and equipment are both grounded by the plug C ra E o sy Page 16 Fabric Care Care Label Guide The following information is provided by U S Federal Trade Commission as part of Project Clean The sym
32. spins during spin cycle 14 Pull on the door to make sure it does not open 15 Allow the cycle to finish Release start button to unlock door Allow 2 3 minutes for door to unlock 16 Open door take out laundry 17 Verify laundry is clean and dry Fold and put away 18 Repeat 1 to 8 for a second cotton load of 6 Ibs Do not overload 19 Press Antiwrinkle button 20 Press Start 21 Check if your clothes are wrinkle free OANA MNAWNE Oo ON ADH KH Make any corrections necessary to properly complete the installation If in doubt call tollfree 1 866 517 7827 for guidance on installation issues WARNING Proper installation is the responsibility of the owner Service performed as a result of improper setup adjustment or connection are the responsibility of the installer Page 6 Installation sheet Shipping Bolts Plumbing Spacers Max 36 inches a 5 na j A Should be 36 inches maximum and 28 inches minimum TAa Feet Nee i J Lower Adjustable Feet 3 yS uoejjeasu Page 7 Water and Electrical Requirements a gt Electrical 1 Jw 110V 60Hz 20 30 Amp fuse or circuit breaker lt y We recommend a dedicated circuit meant only for the washer dryer The washer dryer is equipped with a power cord and a three prong NEMA 5 20P plug Never use an extension cord An electrical ground is required on this appliance This unit is
33. tifreeze in water Unplug washer dryer or disconnect power To Use Washer Dryer Again e Flush out Water pipe and hose e Reconnect Water inlet hose e Turn on water tap e Plug in washer dryer or reconnect power e Run washer dryer through a complete automatic cycle Choose program four position on the dial e Load the detergent drawer compartment two with 4 41 ounces of low sudsing detergent to clean out anti freeze Note Please make sure it is safe to discharge antifreeze into your drain pipe before doing SO To Transport the Washer Dryer e Shut the water tap e Disconnect and drain water inlet hose e Disconnect drain hose from the drain system e If your washer dryer is moved during freezing weather winterize it before moving e Unplug washer dryer or disconnect power e Wash lint filter e Make sure leveling legs are secure e Place inlet hose into the drum e Drape power cord and drain hose over edge and secure it firmly with tape e Insert shipping bolts and spacers e Use masking tape to secure washer dryer door Reinstalling your Washer Dryer Follow installation instructions as given Run the washer dryer through an automatic cycle Select program four Use one scoop or cap full of detergent to remove the antifreeze if used Load detergent in compartment two lt te A gY m e gY gt 2 er oO 74 rF S g Q oO Page 15 i A Safety Feature
34. ts intended purpose as you will find described in this Use and Care Guide This washer dryer must be properly installed and located in accordance with installation instructions before it is used If you did not receive an installation instructions sheet with this book please call 1 866 517 7827to receive assistance in installation This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead of the appliance Connect to a properly rated protected and sized power supply circuit to avoid electrical overload Do not store or use combustible materials gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance Use only detergents recommended for use in a front loading washer Do not wash steel plastic knives or other hard or abrasive items to avoid damage to the drum To minimize the possibility of injury e Do not touch the heating element during or immediately after use e Do not abuse or tamper with controls e Do not sit on or stand on the top of the appliance e Close supervision is necessary if this appliance is used by or near children Do not allow children to play inside on or with this appliance Dispose of discarded appliances and shipping or packing material properly Before discarding a washer dryer remove the door e Keep all wash
Download Pdf Manuals
Related Search