PT9200-SDI - EasternCCTV
Contents
1. 13 4 7 Password 14 4 8 Clock setting 15 4 9 Coom setting 16 5 Camera setting 17 5 1 Zoom 17 5 2 Digital zoom control 18 5 3 Back light compensation 19 5 4 Slow shutter control 20 5 5 Line Sync control 21 5 6 WDR 22 5 7 Advance setting 1 23 5 8 Advance settin g2 24 5 8 1 AE2. 24 5 8 2 White balance 25 6 Function setting 26 6 1 26 6 2 27 6 3 28 6 4 29 6 5 30 6 6 Time running 31 6 7 Set auto trackin g 32 7 Privacy zone masking 33 8 Alarm function 34 8 1 ARM Setting 35 9 1
3. 36 9 1 Menu 36 9 2 Troubleshooting 37 9 3 The cleaning of the down covet 38 9 4 24VAC Wire Diameter and Transmission Distance Comparison chart 38 10 Installtion instuction 39 10 1 Ceiling mount installation instruction 39 10 2 Wall mountion instruction 40 11 Maintenance service terms 41 xD Precaution 1 Precaution Please read this manual and product label carefully before installing the speed dome y Law The product installation and use of the product must comply with the relevant laws of the country y Electrical safety 1 Strictly conform to country and local electrical safety standard when using or installing the product 2 Using factory s power adapter This dome uses 24VAC power supply About the rated inputting voltage please refer to power label y Transportation 1 The dome should be pro
4. 6 4 1 1 Self testing 6 4 1 2 Call the main menu 6 4 1 3 Menu and keyboard operation 6 4 2 Edit dome 1 7 4 3 Initial information 8 4 4 Display setup 9 4 5 Systematic motion 1 10 4 5 1 Auto flip 10 4 5 2 Proportion 10 4 5 3 Park 11 4 5 4 Power up 11 4 5 5 Fan startup by temperature 11 4 5 6 Advance setting 12 4 6
5. Baud rate Max distance 2400BPS 1800m 4800BPS 1200m 9600BPS 800m 19200BPS 600m If user selects thinner cables or installs the dome in an environment with strong electromagnetic interference or connects lots of equipment to the Rs485Bus the maximum transmitting distance will be decreased To increase the maximum transmitting distance do the contrary y RS485Bus troubles shooting In such circumstances the Factory recommends the usages of Rs485 distributor The distributor can change the star configuration connection to the mode of connection stipulated in the Rs485 standards The new connection achieves reliable data transmission Refer to picture 11 4 5 Rs485Distributor 3 1202C J fi B I 1 1100 24 110 0 1 3 Picture 11 4 5 Trouble Possible cause Solution 1 The address and baud rate setting of dome Dome can do self testi eee re 2 The and connection of RS485 Bus is incorrect 3 bad connection 4 There are circuit in the Rs485Bus but cannot be controlled are not in conformity with those of controller 1 Change the address and baud rate of controller or dome 2 Adjust the and connection of Rs485 3 Make sure the connections are fully seated 4 Change Rs485 Bus wires 1 The Rs485Bus is not in good contact with the connectors
6. HD SDI Mini High Speed Dome Installation and Operation Manual TABLE OF CONTENT 1 1 2 2 2 1 Dome parametet 2 2 2 Camera parametet 2 2 3 Performance and 3 3 Function instruction 4 3 1 Camera 4 3 2 Auto run 4 3 3 Camera 1 5 3 4 Monitor 5 4 System setting 6 4 1 Basic
7. FAR Focus to far NEAR Focus to near TELE Increase magnification WIDE Reduce magnification Joystick to up When choosing menu it means to choose the former one when choosing picture it means camera tilt up Joystick to down when choosing menu it means to choose the next one when choosing picture it means camera tilt down Joystick to left when choosing menu itis equal with Close when choosing picture it means camera tilt left Joystick to right when choosing menu it is equal with Open when choosing picture it means camera tilt right Press TELE and WIDE atthe same time it means 3D joystick rotates joystick cap Menu operation Back Back to the former menu On Open one setting Exit Exit menu Off Close one setting WW System Setting 4 2 Edit dome label MAIN MENU When using alot of domes systems in order to identify each dome SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING the systems support title setting The setting ways as follow 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds ALARMS EXIT 2 Operate joystick and move cursor to SYSTEM SETTING and press OPEN to enter into the next menu 3 Operate joystick and move cursor to EDIT DOME LABEL and press 5 OPEN to enter into the label setting menu SYSTEM SETTING ED
8. press OPEN to enter digital zoom setting tilt up down joystick to choose ON means open digital zoom control which is digital zoom is pulled near if pulling the digital zoom near again the dome enters into digital zoom increase to choose OFF means to close digital zoom control 4 Press OPEN to save OPERATION KNACKS When digital zoom be set as ON the maximum zoom magni fication of the dome is digital zoom magnification times optical zoom magnification when digital zoom be set as OFF the maximum zoom magnification of the dome is optical zoom magnification The option of the digital zoom is ON OFF when the camera module is SONY LG CNB HITACHI Y When shows N A it means this camera module does nothave this function NOTICE MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON LINE SYNC N A WDR MODE N A ADVANCE SETTING 1 ADVANCE SETTING 2 BACK EXIT W Camera Setting 5 3 Back light compensation 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursor to CAMERA SETTING to enter submenu 3 Operate joystick and move cursor to BLC MODE press OPEN There willbe a sign inthe front of BLC MODE
9. OPERATION KNACKS When manually adjusting for far focus situation the dome responds at a high speed so that touching rocker slightly may make picture move rapidly thus cause the picture to lose To base on humanized design the dome automatically adjust pan and tilt rotation according to zoom near and far which make it is convenient to operate manually run after object MOTION AUTO FLIP ON PROPORTION ON PARK TIME 005 PARK ACTION SCAN POWER ACTION AUTO FAN ENABLED 050 TEMP C F CENT ADVANCE SETTING BACK MOTION AUTO FLIP ON PROPORTION ON PARK TIME 005 PARK ACTION SCAN POWER ACTION AUTO FAN ENABLED 050 TEMP CENT ADVANCE SETTING BACK MOTION AUTO FLIP ON PROPORTION ON PARK TIME 005 PARK ACTION SCAN POWER ACTION AUDI FAN ENABLED 050C TEMP CENT ADVANCE SETTING BACK tw System Setting 4 5 3 Park action This setting allows the dome to run an appointed action after it enters vacancy for a few time 1 240minutes If default sets as 0 it means not to run this action 1 Operate joystick and move the cursor to PARK TIME press OPEN to tilt up down joystick to set park time the range is 0 240 minute press OPEN to save PARK ACTON is running action ata park time when PARK TIME sets as 0 this item can t be set 2 Operate joystick move the cursor to PARK ACTON press OPEN there will be a sign inthe
10. e All the menu option is displayed in English e Video OSD menu It is direct and simple to revise the dome information and parameter by keyboard and menu display May set park action and set power up action or carry out appointed action 5 Internal temperature test When the temperature exceeds the upper limit the screen will display alarm information e According to the real time temperature the fan will measure if it starts or not and prolong the life of fan 6 Alarm input output control When the dome receives an outer alarm signal it will run the setted motion until alarm released The dome can set 4 alarm input and 1 alarm output Function Instruction 2 3 Function instruction This passage mainly describes the main function and general principle of integrated speed dome and don t refer to the concrete operation methods Different system platform has different operation methods generally we should according to the system manufactory operation manual Please contact franchiser to get necessary information under some conditions there are have some particular requirements and operations 3 1 Auto run motion 1 Auto flip If user holds the joystick at the down position the camera rotates pan 180 degrees then the camera rotates tilts up to 90 degrees you may directly watch the rear view to realize surveillance all processes in portrait 1 80degrees the menu you may set the system parameter setting AUTO FLI
11. N FUNCTION SETTING PRESETS SCAN PATTERNS TOUR ZONES TME RUNNING AUTO TRAC KING BACK EXIT PATTERNS PATTERN NUMBER PROGRAM PATTERN RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL BACK EXIT EDIT PATTERN LABEL L PATTERN 1 BACK EXIT 28 6 3 Pattern Pattern is built in function in camera the speed dome can record tracks that are no less than 180s A series of pan tilt controlling and lens controlling command A dome may set up to 4 patterns 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to FUNCTION SETTING press OPEN to enter submenu 3 Operate joystick to PATTERN press OPEN toenter menu Pattern PATTERN NUMBER PROGRAM PATTERN RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL 4 Choose pattern number move the cursor to PATTERN NUMBER press OPEN pattern you choose as current pattern the following operations aim at the current pattern 5 Define current pattern tour move the cursor to PROGRAM PATTERN press OPEN to set pattern track move the image random and draw the focus The dome has a tour that is no less than 180s a series of park time magnification focus will be recorded press OPEN to save 6 Run pattern operate joystick to RUN PATTERN press OPEN torun the dome will continuously and repeated
12. OFF It means that user can enter into the main menu without password The password function is effective under the password ON It means user need input pass word to enter into the main menu When user forgot the password can not enter into the D main menu he can use the super password to enter which is 892226 At this time the password of dome will NOTICE ae change to initial one which is 000000 and then user may set the password by himself again MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETTING CLOCK SETTING COMM SETIING BACK EXIT CLOCK SETTING TIME 03 20 18 DATE 07 10 10 DAY WED BACK EXIT WOD System Setting 4 8 Clock setting 1 Call 95 preset or call 9 preset twice within 3 seconds and then input the password to enter into the main menu 2 Operate the joystick up and down and move the cursor to SYSTEM SETTING press OPEN tocall the submenu 3 Operate the joystick up and down and move the cursor to CLOCK SETTING press OPEN to call the submenu Please refer to the left picture 4 Operate the joystick and move the cursor to TIME press OPEN to choose it move the joystick up and down to choose the number you need move the joystick right and left to set hour minute se
13. frontof PARK ACTON the cursor jumps to right after tilting up down joystick to choose park action there are options for choosing as follow press OPEN to save NONE default none action PRESET use preset 1 SCAN runscan PAT run pattern e TOUR runtour 4 5 4 Power up action The dome startup to run actions after self testing if nobody intervenes with it the dome will repeatedly run this action continuously default setsas NONE 1 Operate joystick move the cursorto POWER UPACTION press OPEN tojump the following choice tilt up down joystick to choose power up action press OPEN tosave e NONE none action AUTO the dome resumes the primary action and direction before power up PRESET use preset SCAN run scan PAT1 run pattern TOUR run tour 4 5 5 Fan startup by temperature The temperature of the dome will rise when its environment is in high temperature The fan will open automatically when the temperature reaches to a temperature value in order to make sure the stability of the dome Operate joystick move the cursor to FAN ENABLED press O PEN the cursor will skip to the back option The user can choose the fan to start up temperature and press OPEN to save itin actual condition The default setting temperature of the fan startup is 45 C The user also can enter into the fan startup setting to adjust the temperature of fan st
14. not enough the switch and power adapter near the dome Video image is not steady and the Power consumption is not enough Replace the power motor is malfunction Controlling line is bad connection 1 Connect 1209 resistance in the dome pan tilt Dome controlling Rs485 loads so many or the distance _ that is far from the controller is not smooth of communication is much far 2 Increase distributor 9 3 The cleaning of clear down cover e To obtain constant clear videos user should clean the down cover periodically Be caution when cleaning hold the down cover ring only to avoid direct touch to the acrylic down cover The acid sweat mark of fingerprint will corrode the coating of down cover and scratch on down cover will cause vague image e Use soft dry cloth or the substitute to clean the inner and outer surfaces For hand contamination use neutral detergent Any cleanser for high grade furniture is applicable Appendix 5 9 4 RS485 Bus basic knowledge y Characteristics of Rs485 Bus As specified by Rs485 standard Rs485 Bus is of half duplexed data transmission cables with characteristic impedance as 1202 The maximum load capacity is 32unit loads including main controller and controller equipment y Transmission distances of RS485 Bus When user selects the 0 56mm 24AWG twisted pair wires as data transmission cable the maximum theoretical transmitting distance as follow
15. protocols etc Decoder Built in Address setting 0 255 Operation Environmental Pan rotation 360 continuously Operational environment Outdoor 30 50 C Indoor 10 50 C Tilt rotation Tilt90 with auto flip Environmental humidity 0 95 no compensation Rotation speed Pan0 4 320 S Tilt0 4 150 S Protection grade IP66 Weather proof housing outdoor TVS1500w lightning proof surge proof indoor outdoor Alarm function 7 alarm input 2 alarm output Physical Preset 128presets Mount Wall Pendant Corner Pole Surveillance Preset Tour Scan Pattern 2 2 Camera parameter Model 05 3 SE600 Spec Imaging element Scanning system 1 2 8 Type Exmor CMOS Sensor Progressive scanning Effective pixel H x V 2 Mega pixel Minimum illumination 0 25lux 0 03lux Zoom 3x optical 12x digital Focus 3 9 mm IRIS control Auto Manual Focusing system Auto Manual White balance Auto Manual Back light compensation Off No WDR control Yes S N ratio gt 50dB Wide Dynamic Range Off No Auto Privacy zone masking No X Performance 2 3 Dome performance and feature This product is high technology surveillance product with high definition and color camera variable speed pan tilt and multifunction decoder It can reduce the connection and installation process between systematic parts at a max li
16. tilt up down joystick to open or close back light compensation function If choosing ON means to open back light compensation mode if choosing OFF means to close back light compensation mode Different camera different BLC options HLC H High light compensation HLC L Low light compensation WDR H WDR High level WDR M WDR Medium level WDR L WDR Low level Notes When it shows N A it means this camera module does not have this function 4 Press OPEN to save Non use back light compensation in strong sunshine the back light side is subject to dark Use back light compensation the image is in gear OPERATION KNACKS Strong background ray can make backlighting objects engender shadow back light compensation the speed dome can auto adjust iris to match with the changes of various ray and auto revise the main lightness to make the pictures more legible A This function relates to models and parameters of the built in A camera in the dome when open black compensation it has two functions which are auto adjust when you choose ON or manual adjust 0 255 according to the different of the camera NOTICE 19 Camera setting 924 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT CAMERA SETTING ZOOM SPEED HIGH ZOOM OFF BLC MODE OFF SLOW SHUTTER ON UNE SYN
17. 2 One wire of Rs485bus is broken 3 The dome is very far from controller 4 There too many domes connected in The dome can be controlled but the operation is not smooth the system 1 Secure the connection 2 Replace Rs485 bus wires 3 Add termination resistors to the system 4 Install Rs485 distributor 38 10 Installation instruction y Figure corresponding sheet Model Picture Ceiling mount Y Wall mount Details of relevant parts 1 wall bracket 2 Base 3 power cable 4 dome 5 clear cover 1 Ceiling mount Installation instruction 1 1 Dimension of product As picture below Picture 1 1 1 Installation instruction 1 2 Installation of product 1 Drill holes and fix base board on the ceiling floor by using four ST3 5 bolts As picture 1 2 1 Picture 1 2 1 2 Through the cable from the top of the base and fix the four bolt then push the dome up Pull out the cable from the top As picture 1 2 2 Picture 1 2 2 3 Connect the power cable video cable and Rs485 control cable Don t need to connect network cable if itis not dome As picture 1 2 3 Alarm connector Network connector 1 y i Video connector AC 24V 485 485 Green Yell
18. C N A WDR MODE N A ADVANCE SETTING 1 ADVANCE 2 J 20 5 4 Slow shutter control 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursor to CAMERA SETTING to enter submenu 3 Operate joystick and move cursor to SLOW SHUTTER press OPEN there willbeasign inthe frontof SLOW SHUTTER tilt up down joystick to slow shutter choice if choosing ON means to open slow shutter have more options for light time of slow shutter from X2 X128 4 Press OPEN to save OPERATION KNACKS is shoot in dark more legible When the dome monitors at night or dark environment because the ray is not enough the image on the screen is too dark setting slow shutter can lengthen the time of lighting so that make the picture that AN This function depends on the models and parameters e of built in camera in dome if the camera doesn t have NOTICE this function then this function is invalid gt function if choosing OFF means close slow shutter function Some cameras MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON LINE SYNC N A WDR MODE N A ADVANCE SETTING 1 ADVANCE SETTING 2 BACK EXIT W Camera
19. CKING is set as gt OFF it is valid to Call preset to set auto tracking ON OFF NOTICE refer to the Paragraph 6 7 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT Va FUNCTION SETTING PRESETS SCAN PATTERNS TOUR ZONES TIME RUNNING AUTO TRAC KING BACK EXIT SCAN SCAN NUMBER 04 SCAN SPEED 50 SET LEFT UMIT SET RIGHT LIMIT RUN SCAN CLEAR SCAN EDIT SCAN LABEL BACK EXIT EDIT SCAN LABEL L AUTO SCAN1 BACK EXIT W Function setting 6 2 Scan Scan is that pre set two points then the camera repeatedly scan between the two points at a stable speed the same magnification and pan Each dome has four scan tour 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds Click menu to enter scan menu as the left picture shows SCAN NUMBER SCAN SPEED 1 SET LEFT LIMIT SET RIGHT LIMIT RUN SCAN CLEAR SCAN EDIT SCAN LABEL 2 Define current scan number operate joystick move the cursor to scan number press open tilt up downjoystick to choose scan number press open to save The following operations aim at the current scan number 3 Scan speed setting operate joystick to SCAN SPEED press OPEN tilt up down joystick to adjust scan speed press OPEN to save 4 Left limit setting operate joystic
20. FUNCTION SETTING press OPEN to call the submenu 3 Operate the joystick and move the cursorto TIME RUNNING press OPEN to enter into the menu setting Please refer to the left picture e DAY set the date e TIME CHANNEL 4 channels can be set e STARTTIME Set the start time e Set the end time e RUNNING Usercan set the preset scan tour pattern to every channel 1 4 e TRK A1 Whenspeeddomerun TOUR inthis time it will auto open auto tracking and AUX 1 if discovering moving objection 4 This channel will not conflict with other channels when you set RUNNING as close 1 When user run the action of scan tour or pattern if time is over then the Dome will execute park action the user s action will stop After the time the dome will resume the action and preset which is set before the park time Before the park time if the dome is on some preset the dome will resume the preset if domes execute the action of scanning tour or pattern the dome will resume original action If users handle some action with keyboard dome will also resume A the action which users are going on with keyboard 2 During the timing period of movement function it is not allowed NOTICE that there is no action When users handle the dome the timing movement function will interrupt If there is no any action during 10 seconds it will be in the state of timing function and return to the timing movem
21. G PRESETS SC AN PATTERNS TOUR ZONES TIME RUNNING AUTO TRAC KING BACK EXIT Va PRESETS PRESET NUMBER 05 SET PRESET SHOW PRESET CLEAR PRESET AUTO TARCKING NONE EDIT PRESET LABEL BACK EXIT J EDIT PRESET LABEL L PRESEFO5 BACK EXIT 26 6 Function setting 6 1 Preset 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds Click each command to enter preset menu according to the order of the left picture As follows e PRESET NUMBER SET PRESET SHOW PRESET CLEAR PRESET AUTO TARCKING If the dome does not have this function it won t display EDIT PRESET LABEL Define preset and call preset function can be set by keyboard operation input preset number at first then click the key save call preset to carry out 2 Define current preset number move the cursor to PRESET NUMBER press OPEN to choose preset number the range is 1 128 as the left picture shows here chooses number 5 as current preset the following operations aim at the current preset 3 Define current preset move the cursor to SET PRESET OPEN by operating joystick to adjust magnification to choose good objective image press OPEN to save If the image is very near the Image is belong in digital zoom When setting preset the image will jump to maximal optical zoom OPERATION KNACKS P
22. IT DOME LABEL 4 Operate joystick and move cursor to LABEL and press OPEN to INITIAL INFO edit current label DISPLAY SETUP MOTON 5 When the cursor is twinkling in the first character of the label to move CLEAR joystick to choose character after editing pressing OPEN to save PASSWO RD SETUP an A 7 Moving cursor to BACK and pressing OPEN to back to the BACK ormer menu C EXIT The label may set 16 characters and doesn t need editing EDIT DOME LABEL characters Pressing OPEN continuously to jump over and using spacebar to replace the deleted characters When you finish to edit a character press OPEN to enter into the next editing HD SPEED DOME BACK character when you editing the last character pressing OPEN EXIT tosave Press Close to exit A Character of label is suitable for choosing as follow 0 9 A Z 2 amp to show Space NOTICE Other labels input ways the same as above System setting C MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP CLOCK SETTING COMM SETTING BACK EXIT INITIAL INFO FIRMWARE V1 23 PROTO COL FAC TORY DOME ADDRESS 000 COMM 4800 N 8 1 BACK EXIT 4 3 Initial information 1 The system enters into the main menu by calling 95 prese
23. ITIAL INFO MIRROR ON EXIT FLIP OFF FIRMWARE V1 23 NEXT PROTOCOL FACTORY a SRT SCANER ARM SETTING DOME ADDRESS 000 SCANNUMBER 04 L AUTOSCAN COMM 4800 8 1 NEXT SCAN SPEED 50 BACK DAY SUN BACK SET LEFT LIMIT EXIT OFF EXIT SHARPNESS 005 SET RIGHT LIMIT ARM TIME NIA PS SCAN OFF RUN SCAN ONLEN ONE WA STABLE ZOOM OFF CLEAR SCAN MAGE DNR OFF EDIT SCAN LABEL eo DISPLAY SETUP VIDEO MODE 1080160 BACK BACK EXIT DOME LABEL OFF EXIT PRESET LABEL OFF ZOOM LABEL ON ZONE LABEL OFF PATTERNS EDIT PATTERN LABEL DIR LABEL ON ADVANCE SETTING 2 PATTERN NUMBER TE AREE on AE MODE AUTO PROGRAM PATTERN E ARTERNA BACK DATE LABEL ON SHUTTER NA RUN PATTERN EXIT BACK IRIS N A CLEAR PATTERN BRIGHT N A EDIT PATTERN LABEL WB MODE AUTO BACK R GAIN N A EXIT MOTION B GAIN N A EDITTOUR AUTO FLIP ON HI RESOLU 018 PROPORTION ON BACK PO 5 005 TOUR 00 0 00 00 0 00 PARK ACTION SCAN 20 000 00 POWER ACTION AUTO TOUR NUMBER 1 00 0 00 00 0 00 FAN ENABLED 045C ADVANCE SETTING EDIT TOUR 00 0 00 00 0 00 TEMP C F CENT RUN TOUR 90 90 09 00 0 00 ADVANCE SETTING EISENABLED OFF CLEAR TOUR 88 08 88 88 8 88 BACK PRESET FREEZE OFF BACK AUTO FOCUS OFF EXIT BACK DEFOGGER 015 CLEAR HEAD UP ON BACK CLEAR ALL ZONES EXIT CLEAR ALL PRESETS ZONES EDIT ZONE LABEL CLEAR ALL PATTERNS CLEAR ALL TOURS ZONES NUMBER 1 L ZONE 1 CLEAR ALL WINDOWS SET LEFT LIMIT BACK FACTORY DEFAULTS SET RIGHT LIMIT EXIT RESTART CLEAR ZONE BACK EDIT Z
24. ONE LABEL EXIT BACK EXIT PASSWORD SETUP OLD NEW TIME RUNNING ENABLE OFF DAY SAT BACK TIME CHANNEL 1 EXIT START TIME 00 00 END TIME 00 00 RUNNING TOURI CLOCK SETTING BACK EXIT TIME 03 20 18 DATE 07 10 10 DAY WED EXIT AUTO TRACKING TRACKING PARA DAY THU SET LEFT LIMET STATE OFF TIME SET RIGHT LIMET COMM SETTING START TIME 00 00 SET UP LIMET END TIME 00 00 SET DOWN LIMET SENSITIVE MID S N 4JKAA7824000058 CONF 4JKAA7824000058 SITEID 001 COMM SPEED 4800BPS BACK EXIT 36 TRACKING ZOOM OFF TRACKING SPEED MID TRACKING PARA BACK EXIT PARKTIME 000s BACK EXIT PARK ACTION NONE W Appendix 9 2 Trouble shooting Trouble Possible causes Solution Power supply is damage or power consumption is not enough Replace No self testing no video after power up Power line is bad connection Correct Engineering line is malfunction Check and repair The dome DIP switch setting is Refer to switch setting reset the switch incorrect Self testing and Check Rs485connection confirm image are normal RS485 may carve out a way the connection is correct and but the dome is good in contact uncontrollable Pls consult appendix Rs485 Bus acknowledge RS485 is in malfunction Video line is bad connection Eliminate Video image is not steady Replace right power adapter it is better to put Power consumption is
25. P as ON thus you may run this function 2 Park action By the menu park time and park action user may set auto call preset or run tour pattern and scan etc after pointing a few minutes if the dome doesn t run any motions 3 Power up action By the menu power up action after the dome powers up or restarts user may set auto resume motions before power up and auto call preset or run tour pattern and scanetc 3 2 Camera control 1 Magnification control The user can adjust zoom far and near of the image by keyboard controller Wide Tele to obtain panoramic image or close view that you need The speed dome support digital zoom and optical zoom 2 Focus control System defaults Auto focus When the lens changes camera will auto adjust focus according to the centre of the image to get legible image User also can manually focus to get desire image by operating keyboard FAR NEAR When operating keyboard joystick camera resumes to auto focus The camera can not auto focus in the following status Target is not inthe centre of the image Observe the target near and far at the same time can not be clear at the same time Target 15 a strong light object suchas spotlight neon light etc Target moves too fast Target area such as wall Target is too dark or vague Target image is too small W Function Instruction 3 Iris control System defaults as
26. R ACTION AUTO FAN ENABLED 050 TEMP CENT ADVANCE SETTING BACK J 10 4 5 Systematic motion control Systematic motion controlling may control a series of canonical mov ement of the dome and plays an important role in controlling the image of the dome 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursor to SYSTEM SETTING press OPEN to enter submenu 3 Operate joystick and move cursor to MOTION press OPEN to enter systematic motion controlling menu as left picture shows 4 5 1 Auto flip 1 Operate joystick move the cursor to AUTO FLIP press OPEN toenter auto flip setting tilt up down joystick for example choosing ON to open auto flip choosing OFF to close auto flip Press OPEN to save OPERATION KNACKS When opening the auto flip function user holds the joystick in the down position the camera rotates pan 180 degrees after the camera rotates tilts up to 90 degrees you may directly watch the rear view to surveillance all processes in portrait 180 degrees 4 5 2 Proportion pan Operate joystick move the cursor to PROPORTIONAL press OPEN toenter proportion pan setting tilt up down joystick to choose if choosing ON it means to open proportion pan if choosing OFF it means to close proportion pan press OPEN to save
27. Setting 5 5 Line sync control 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to CAMERA SETTING press OPEN to enter submenu 3 Operate joystick and move the cursor to LINE SYNC press OPEN tilt up down joystick to set line sync Line sync can divide two kinds internal external choose OFF is internal sync choose ON is external sync 4 Press OPEN to save OPERATION KNACKS When a lot of domes use a line in the same time if the image is twinkling as switching please set each dome as external line and adjust the numerical value of external line This function is relative with the model and parameter of the camera module which insert the dome The option fN is useless N A when the camera module does not have this NOTICE function 2 21 Camera setting 924 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT CAMERA SETTING ZOOM SPEED HIGH DIGIMAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON LINE SYNC N A WDR MODE N A ADVANCE SETTING1 ADVANCE 2 4 22 5 6 WDR Control 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to CAMERA SETTING press OPEN Enter the
28. TART 4 Set clear zone as anexample to explain the process Tilt up down joystick to CLEAR ALL ZONES press OPEN to clear all zones Once clear all commands the controlling menu it can t resume so please be careful of using it NOTICE 13 System setting C MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT SYSTEM SETTING N EDIT DOME LABEL INITAL INFO DISPLAY SETUP MOTON CLEAR PASSWORD SETUP CLOCK SETTING COMM SETIING BACK EXIT PASSWORD SETUP OLD NEW ENABLE OFF 14 4 7 Password setup 1 Call 95 preset or call 9 preset twice within 3 seconds and then input the password to enter the main menu 2 Operate the joystick and move the cursorto SYSTEM SETTING press OPEN to call the submenu 3 Operate the joystick and move the cursorto PASSWORD SETUP press OPEN tocall the submenu Please refer to the left picture 4 Operate the joystick and move the cursorto OLD PASSWORD press OPEN to choose it operate the joystick right and left to input the password Tilt up and down to choose the number which you need NEW PASSWORD Enter the new password CONFIRM PASSWORD Confirm the new password ENABLE PASSWORD 1 Set password ON OFF The password function is noneffective under PASSWORD
29. Warranty terms e If the products are within the warranty time the buyer should fill in the warranty card and send back together with the products 3 Shipping e Ifthe product needs repaired you can return it to the manufacturer through the supplier or directly If you choose the later please contact us in order to speed up the process And our company only undertake the one way freight from manufacturer to customer after maintenance 41
30. XIT CAMERA SETTING ZOOM SPEED HIG H DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON LINE SYNC N A WDR MODE N A ADVANCE SETTING 1 ADVANCE SETTING 2 BACK EXIT S ADVANCE SETTING AE MODE AUTO SHUTTER N A IRIS N A BRIG HT N A WB MODE AUTO R GAIN N A B GAIN N A HI RESOLU 108 BACK 24 5 8 Advance setting 2 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to CAMERA SETTING to enter submenu 3 Operate joystick and move the cursor to ADVANCE SETTING press OPEN to enter submenu as left picture shows 5 8 1 AE mode 1 Operate joystick and move the cursor to AE MODE press OPEN tilt up down joystick to choose AE mode modes for choosing as follow AUTO default setting auto Iris mode BRIGHT brightness priority mode IRIS iris priority mode SHUTTER shutter priority mode MANUAL manual priority mode 2 Choose iris priority mode IRIS press OPEN to save 3 Move joystick to the sub choices of AE mode IRIS F1 4 press OPEN to choose adequate Iris press OPEN to save e SHUTTER priority this function can be set 1 50 it means shutter speed when AE mode is shutter e IRIS F1 4 it means the size of iris when AE mode is iris priority this function can be set e BRIGHT _ F2 0 ODB it means brightness when AE mode is brightness p
31. alarm off time BACK back to the former menu EXIT Exit the menu 35 Appendix C 9 1 Menu Index MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EDIT DOME LABEL ZOOM SPEED HIGH ESETS INITIAL INFO DIGITAL ZOOM OFF WINDOW NUMBER 01 SEQUENCE On DISPLAY SETUP BLC MODE OFF PATTERNS EDIT WINDOW RESET DELAY 020 MOTION SLOW SHUTTER OFF TOUR ENABLE WINDOW OFF ALARM CONTACT N C CLEAR LINE SYNC N A ZONES COPAR WINDOW ALARM SETTING PASSWORD SETUP WDR MODE N A TIME RUNNING BACK ARM SETTING CLOCK SETTING ADVANCE SETTING 1 AUTO TRACKING EXIT BACK COMM SETTING ADVANCE SETTING2 BACK EXIT BACK BACK EXIT EXIT EDIT DOME LABEL PRESETS EDIT PRESET LABEL ALARM SETTING ADVANCE SETTING1 i HG SPEED DOME PRESET NUMBER 05 ALARM ROMBER 001 B amp W AUTO SEL PRESET BACK ALARM ACTION TOUR EXIT BLACK TIME N A SHOW PRESET EXIT ACTIVATE AUX NONE COLORTIME CLEAR PRESET ALARM PRIORITY HIGH THRESHOLD 10dB AUTO TARCKING NONE BACK MAX GAIN 08dB SA ee LABEL EXIT EXPOS COMP ON IN
32. artup As picture shows the temperature range is 0 60 C switch the temperature between Fahrenheit and Centigrade System setting C MOTION AUTO FLIP ON PROPORTION ON PARK TIME 005 PARK ACTION SCAN POWER ACTION AUTO FAN ENABLED 050 TEMP C F CENT ADVANCE SETTING BACK ADVANCE SETTING EIS ENABLED OFF PRESETFREEZE OFF AUTO FOCUS ON DEFOGGER 015C HEAD UP OFF BACK EXIT 12 4 5 6 Advance setting 1 Operate joystick and move the cursor to ADVANCE SETTING press OPEN to enter into advance setting EIS ENABLED Electronic Image Stabilizer function e PRESET FREEZE means the image will be frozen at the point that you call the new preset until the camera totally gets the new preset the freezed image can be released e LAUTO FOCUS Choose ON OFF to open close the auto focus of the dome DEFOGGER Clear cover will be fogged when the dome works in quite cold temperature In order to ensure to get clear image defogger runs at the appointed temperature Choosing DEFOGGED by operating the joystick and press OPEN and enter into the next buttons Please choose the temperature lever to run the defogged and press OPEN to save Range of temperature 0 30 C HEAD UP When dome used as head down pls choose choose OFF OPERATION KNACKS After the dome set the EIS function if the dome wobble sligh
33. auto Iris Cameracan rapidly adjust size of Iris through automatically induct the changing of environment ray and thus make the brightness of deferent image stable User may adjust Iris by controller keyboard open close to get required brightness that you need User also can resume auto Iris by joystick operation When controlling the Iris manually the dome locks current position you manually controlled when operating joystick the dome resume auto Iris 4 Auto back light compensation Camera sub area can carry out auto back light compensation Under a strong light background camera will auto compensate light for the darker object and adjust daylight to the bright background In order to avoid making the image mess by the background is too high in luminance and the object is unable to recognize because of darkness thus gain legible image 5 Auto white balance Camera can automatically adjust white balance in accordance with the alteration of background lightness to reach a true colour 3 3 Monitor function 1 Set and call preset Preset function is that dome stores the horizontal angle slope angle camera lens focus position and parameters of current pan tilt into the memory When necessary dome cancall these parameters and adjust pan tilt and camera to this position User call presets easily and promptly by using keyboard controlling The dome can support 128 presets 2 Tour Tour is the built in function in the sp
34. ay dome label as an example to explain the operation process Tilt up down joystick to move cursor to DOME LABEL OFF press OPEN thereisasign besides DOME LABEL the cursor is twinkling besides OFF as left picture shows 5 Joystick tilts up down setting number changes between ON OFF when setting LON it means to display dome label when setting OFF it means not to display dome label When pressing OPEN the cursor jump back in front of DOME LABEL means label setting is finished when moving the cursorto BACK it means exiting the current menu setting The displaying information on the screen will change with the dome rotation Through the information on the screen user can see dome current inside temperature magnification display zone etc When all the label are displayed the dome works as the following picture shows Inthe picture 305 means pan angle 45 means tilt angle Dome label Temperature label Date label Time label j4 21 lt Zoom magnification label System setting C MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT 5 5 5 EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP CLOCK SETTING COMM SETTING BACK MOTION AUTO FLIP ON PROPORTION ON PARK TIME 005 PARK ACTION SCAN POWE
35. cond DATE set year month date DAY set week BACK return to the former menu EXIT exit the main menu 15 16 Camera setting 924 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETTING CLOCK SETTING COMM SETTING BACK EXIT COMM SETTING S N 4JKAA7824000058 CONF 4JKAA7824000058 SITE ID 001 COMM SPEED 4800BPS BACK EXIT 4 9 COMM Setting 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to SYSTEM SETTING press OPEN to enter into the next menu 3 Operate joystick and move the cursor to COMM SETTING press OPEN to enter into dome parameter setup menu S N show Series NO of the dome ex work CONF to confirm the series number of the dome it should be the same as the S N SITE ID setting up the ID number of the dome address scope 001 255 COMM SPEED Baud rate setup The user can choose 4 kinds of Baud rate 2400 BPS 4800 BPS 9600 BPS 19200 BPS PROTOCOL set protocol the user can choose 16 kinds of protocol PELCO FACTORY DYNACOLOR ISD HUNDA VIDO B02 LILIN KALATEL DIAMOND SAMSUNG PANASONIC SANTACHI VICON MOLYNX VCL SAE These operation can t be continue
36. d if two series number NOTICE not the same MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT S CAMERA SETTING ZOOM SPEED HIGH DIGIAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON LINE SYNC N A WDR MODE N A ADVANCE 1 ADVANCE SETTING2 BACK W Camera Setting 5 Camera setting 5 1 Zoom speed 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursor to CAMERA SETTING press OPEN to enter submenu 3 Operate joystick and move cursor to ZOOM SPEED press OPEN x will appear in the front of HIGH the cursor moves to right tilt up down joystick to choose HIGH or LOW 4 Press OPEN tosave press CLOSE tocancel 17 Camera setting 924 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT N CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON LINE SYNC N A WDR MODE N A ADVANCE 1 ADVANCE SETTING2 BACK EXIT 5 2 Digital zoom control 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursor to CAMERA SETTING press OPEN to enter camera setting 3 Operate joystick move the cursorto DIGITAL ZOOM
37. eed dome It can appoint setting in advance and make presets arranged in needful order in tour dwell By inserting presets in tour dwell to make the camera tour between these presets Tour order can be programmed each time you run tour you can set park time A tour can store16 presets 3 Scan User can easily preset right limit and left limit by controlling keyboard and menu in order to make the camera scanned between right limit and left limit at a setting speed 4 Pattern Pattern is built in function in the speed dome the dome can record the tracks that are no less than 180s when running pattern the dome moves repeatedly according to the recorded tracks Adome can set up to 4 pattern 5 Lens position display The position that the speed dome has finished to self testing as 0 point of pan rotation and tilt rotation The pan range is 0 360 and tilt range is 0 90 According to the displayed information to set the position of camera lens and the position can display on the screen 3 4 Constant temperature function Inner temperature sensor check temperature inside of the dome When the dome work at the high temperature the dome will automatically to start up the fan to reduce the heat to make sure the dome work in the reliable temperature environment increase its stability and prolong the life time of the dome System setting C 4 System setting 4 1 Basic operation 4 1 1 Self testing The dome conducts self testin
38. ent function Or if there is idle function it will be do the action of idle time function 3 Timing function will close while user setting presets right and left limit menu status recording scan and setting any other function 31 Function setting C4 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT FUNCTION SETTING PRESETS SC AN PATTERNS TOUR ZONES TIME RUNNING AUTO TRAC KING BACK EXIT AUTO TRACKING DAY THU SIATE START TIME 00 00 END TIME 00 00 SENSITIVE MID TRACKING ZOOM_ OFF TRACKING SPEED MID TRACKING PARA BACK EXIT gt TRACKING PARA SETLEFT UMET SETRIGHT LIMET SETUP LIMET SETDOWN LUMET PAPK TIME 0005 PAPKACTION NONE BACK EXIT 32 6 7 Set auto tracking When initiate Auto tracking function the speed dome automatically captures the picture of the moving object thus real timely tracking 1 Call 95 preset or call 9 preset twice within 3 seconds input password to enter the main menu 2 Operate the joystick to move the cursor to FUNCTION SETTING press OPEN to enter the next menu 3 Operate the joystick to move the cursor to AUTO TRACKING press OPEN to enter the next menu as showed on the left picture 4 Set left limit of the motion detection area operate the joystick to SET LEFT LIMIT press OPEN operate joystick
39. es high middle low HAAR ABER Ae Calan to AUK AUXI Teyp ara LP Alarm input 1 7bits L dpcearthing J gt Alarm output 1 gt Alarm output 2 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT 2 N ALARMS RESUME OFF SEQ UENC E 002 RESET DELAY 020 ALARM CONTACT N C ALARM SETTING ARM SETTING BACK EXIT S ARM SETTING DAY SUN ARM 5 OFF ARM TME N A UNARM TIME BACK EXIT x Alarm Function 8 1 ARM Setting 1 Call 95 preset or call 9 preset twice within 3 seconds and then input the password to enter the main menu 2 Operate the joystick up and down move the cursor to ALARMS press OPEN to call the submenu 3 Operate the joystick up and down move the cursor to ARM SETTING press OPEN tocall the submenu Please refer to the left picture 4 Operate the joystick up and down move the cursor to DAY Press OPEN tochoose it Operate the joystick up and down to set date set the date according to the week To set the Alarm state and Alarm date based on the time ARM STATE Alarm off Alarm on Alarm Setting is noneffective under Alarm off Alarm Setting is effective under Alarm on ARM TIME User can set the alarm time UNARM TIME User can set the
40. g after current carrying and it rotates slowly until displaying pan origin that is default setting then moving to tilt origin the lens will be pulled far to near and near to far when self testing is finished there is relevant system information displaying on the screen as follow MERDE M PT Zoom ID a M 48003 q Communication parameter The information will not disappear until you stop to operate the system If you set power up action the dome will automatically activate motions after self testing How to operate the function We will explain detail introduction in following passages 4 1 2 Call the main menu The system enters into the main menu by calling 95preset or 9 preset twice within 3 seconds All the menu setting must enter into the main menu at first You need input password when you sign in the menu if you set up password and have a super password for the time of forget the password super password 892226 then the password will turn to factory setting original password 000000 You need set the password again if you need it the detail of information show in password setting 6 7 4 1 3 Menu and keyboard operation 1 Basic operations y Keyboard operation OPEN when choosing pictures it means to increase Iris when setting menu it means to enter into the next menu or Setting or save after finishing setting Close when choosing pictures it means to reduce Iris close to cancel
41. il setting as follow 1 The system enters into the main menu by calling 95 preset or by calling 9 y y y 8 preset twice within 3 seconds click each command enter into advanced setting menu according to the order in left picture 2 Operate joystick and move the cursor to WB MODE to choose white balance mode press OPEN to save mode is the default mode of speed dome which is auto revert real color after the white balance sensor check the environment by camera When choosing manual mode MANUAL adjust the numerical value of R GAIN BGAIN GAIN the range is 1 225 the numerical value is bigger it means that adding red is more the tone changes to be warm e B GAIN the range is 1 225 the numerical value is bigger it means that adding green is more the tone changes to be cold Indoor mode INDOOR and the tone leans to cold Outdoor mode OUTDOOR and the tone leans to warm e HI RESOLUTION high resolution is built in function of camera this function is relative with the model of camera It is possible that different camera has not the setting of INDOOR OUTDOOR HI RESOLUTION f e That means the current camera has no such function when NOTICE the setting option shows N A 25 Function setting 2 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT FUNCTION SETTIN
42. k to SET LEFT LIMIT press OPEN operate joystick to choose objective image press OPEN to save Right limit setting is the same as left limit setting 5 Edit scan label operate joystick move the cursor to EDIT SCAN LABEL press OPEN toentersubmenu edit label move the cursorto LABEL the system will auto set the label as AUTO SCAN press OPEN to revise The label can set up to 16 characters and doesn t need editing characters Pressing OPEN continuously to jump over and using spacebar to replace the deleted characters When you finish to edit a NOTICE character pressing OPEN to enter into the next editing character when you finish to edit the last character pressing OPEN to save Press CLOSE to exit Character of label is suitable for choosing as follow 0 9 2 lt gt Space The editing ways of other labels are the same as above 6 Run scan operate joystick to RUN SCAN press OPEN toexit the menu and it stars to run scan 1 Left limit and right limit of scan can t be set the same point D 2 Under scan process speed magnification and tilt direction won t change if the speed magnification and tilt direction of the two NOTICE an 7 limits are inconsistent run scan is base on left limit 27 Function setting 2 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT
43. ly record the specific track When carry out program run clear pattern and edit label should choose pattern number at first NOTICE MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS LANGUAGE EXIT FUNCTION SETTING PRESETS SC AN PATTERNS TOUR ZONES TIME RUNNING AUTO TRAC KING BACK EXIT TOUR TOURNUMBER 1 EDITTOUR RUN TOUR CLEAR TOUR BACK EXIT OOOOO OOO OOOOO OOO SO Function Setting 6 4 Tour Tour is the built in function in the speed dome it will arrange the presets into the queue of auto tour and can set how long it will park at preset Operate auto tour is a process of incessantly transfer each preset One tour can store 16 presets at most 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to FUNCTION SETTING press OPEN to enter submenu 3 Operate joystick move the cursor to TOUR press OPEN to enter menu tour 4 Set the park time of preset Operate joystick and move the cursor to TOUR DWELL press OPEN there will bea sign in the front of TOUR DWELL the cursor jumps to right tilt up down to set park time and the range is 000 255 s 5 Set tour move the cursorto EDIT TOUR press OPEN to set tour interface PO S TM set prese
44. mit and also can improve the stability and reliability of the system Meanwhile it is easy to install and repair and it has the following advantages beautiful shape rotate lightly and neatly little noise simple operation and so on 1 Built in digital camera High sensitivity high resolution and integrated digital processing Auto focus Auto Iris e Auto brightness control Auto white balance IR cut filter Auto back light compensation Auto slow shutter 2 Integrated and multi protocol decoder Figure design all the data is stored in the inner of camera pan tilt when power off the storage data won t lose Built in decoder integrated and multi protocol including PELCO D PELCO P AD PHILIPS KALATEL DIAMOND PANASONIC and so on 128 presets can be stored support auto tour but only can transfer 1 80 presets 4 tour each tour can store up to 16 presets e 4 pattern 4 scan e Built in direction indicator e Built in temperature indicator e Built in clock setting e RS485 bus controlling in series and dome ID 1 255 optional 3 Built in pan tilt e Iron and carbon alloy structure high intensity and good heat dissipation e Precise stepping motor rotate smoothly react sensitivity and orientate accurately e Exquisite mechanical drive support 360 continuously and tilt 0 90 and may rotate180 with auto flip e Rotate slowly at pan 1 s and the image doesn t wobble 4 OSD menu
45. n set 2 masking at most per screen The screen will note please move when the position can not be set It can not set masking when the dome rotates down the level 245 Sony Camera It can be set 24 masking zone at most in 360 surveillance range Sony 45 series can be set 8 masking at most It can not set masking zone when the dome rotates down the level 220 LG CNB Camera module do not have masking function 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick to WINDOW BLANKING press OPEN to enter menu window blanking e WINDOW NUMBER choose window number as current privacy window other choices in the menu just aim at current privacy window e EDIT WINDOW program current window e ENABLE WINDOW permit prohibit current privacy window there are two choices ON permit current privacy window OFF prohibit current privacy window e CLEAR WINDOW clear current privacy window after clearing it the window will auto change as OFF 3 Program current privacy window Firstly choose window number then do the following operations a Operate joystick move the cursor to EDIT WINDOW press OPEN to move the image that need privacy window to display in the screen b Press OPEN there will be a square displaying in the center of the screen operate joystick and move the square to the central place that need to c
46. next main menu 3 operate joystick and move the cursor to WDR MODE press OPEN tilt up down joystick to set WDR Choice ON is open WDR Function choice off is closed WDR if you choice Auto Than mean Auto setting WDR 4 Press OPEN tosave A This function is relative with the model and parameter 1 of the camera module which insert in the dome The option is useless N A when the camera module does not have this function NOTICE MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT ALARMS 3 CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON UNE SYNC N A WDR MODE N A ADVANCE SETING1 ADVANCE SETTING 2 BACK EXIT 9 S ADVANCE SETTING B amp W AUTO BLAC K TIME N A COLOR TIME N A THRESHOLD 10dB MAX GAIN 5 OFF MIRROR OFF FLIP OFF NEXT NEXT SHARPNESS 005 PS SCAN OFF STABLE ZOOM OFF DNR OFF VIDEO 1080160 BACK EXIT W Camera Setting 5 7 Advance setting 1 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to CAMERA SETTING to enter submenu B amp W Day Night switch BLACKTIME Day time switch COLORTIME Nighttime switch e THRESHOLD sensitivity of switch between B W and color The higher numerical value mean
47. ns at the same time It will execute the function under MOTION gt PARK TIME 000 PARK ACTION NONE but but it won t execute the function under TRACKING PARA PARK TIME 0005 PARK ACTION NONE Call 250 preset to set the Auto Tracking function ON Call 251 preset to set the Auto Tracking function OFF The speed dome will not resume keeping the Auto Tracking function when it power on The speed dome will track the moving object at random when there s too many objects in tracking area Too light or too dark will influence fN the effect of auto tracking NOTICE The function relates to the speed dome and build in camera modules the item will not be showedor N A when the camera doesn t have such function MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT S WINDOW BLANKING WINDOW NUMBER 01 EDIT WINDOW ENABLE WINDOW OFF CLEAR WINDOW BACK EXIT Privacy zone masking W Privacy zone masking 7 Privacy zone masking Privacy function can show someone piece of regional shielding while protecting For example protect the window of bedroom or ATM of bank A dome can set up to 24 privacy windows Privacy zone mask function is relative with the model of camera module The masking numbers will be different according to the different cameras Hitachi Camera It be set 8 masking zone at most in 360 surveillance range ca
48. onceal c Press OPEN operate joystick to adjust the size of privacy zone joystick up the height is increased joystick down the height is reduced joystick to right the width is increased joystick to left the width is reduced d Press OPEN to save the current privacy zone setting and the window will auto change as ON at the same time A A N This function is decide by the parameter of built in camera y soy if the camera does not have this function this option is invalid NOTICE 33 Alarm Function C N MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT ka N ALARMS RESUME OFF SEQ UENC E 002 RESET DELAY 020 ALARM CONTACT N C ALARM SETMING ARM SETTING BACK EXIT a N ALARM SETTING NUM BER 01 ACTION TOUR ACTIVATE AUX NONE PRIORITY HIGH BACK EXIT N J 34 8 Alarm function Speed dome may connect with 7 alarm input 2 alarm output and support alarm linkage The external alarm message sends to the dome then the dome sends to alarm point shoot to call preset auto scan auto cruise and auto pattern and choose that to run alarm output or not 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds Click each menu according to the left picture then enter menu alarm choices as follow RESUME resume mode after relieving alarm input the
49. ow Picture 1 2 3 39 Installation instruction 92 2 Wall mount installation instruction 2 1 Dimension of product As picture below 25 220 Picture 2 1 2 2 Installation of product 1 Make the wall bracket as the model on installation wall and draw the central position of the drill hole As picture 2 2 1 75 00 100 00 P Picture 2 2 1 2 Drill four installation holes for M8 metal expand screw with the lashed electric drill on the installation surface and be sure with the installation hole of 75mm depth approximately and M8 expand metal screw As picture 2 2 2 40 Picture 2 2 2 3 Pls make the wall bracket aims at the M8 screw so that the output cable will be locked in the hole of motherboard bracket and use the M8 screw to lock the wall bracket tightly As picture 2 2 3 Picture 2 2 3 4 Connect the power cable video cable and RS485 control cable Don t need to connect network cable if itis not IP dome As picture 1 2 3 Maintenance 11 Maintenance service terms 1 Range of warranty e The product will be maintained free for one year e The product will be obtained the free maintenance service if the same malfunction appears again within three months e Malfunction of products caused by fo
50. rce majeure such as war earthquake lightning strike and soon abuse non standard operation change of construction non normal wear or accident are non free of warranty e Please prevent from the damage which is caused by heavy pressure the fierce vibration and soaks inthe process of transportation and storage which does not belong to the free maintenance scope e Please adopt the way of fission package or original package to transport because the product damage does not belong to the free maintenance scope if you use the whole packing way not the original packing way e The maintenance services will not be free when the pan tilt module is disassembled or serviced by the user voluntarily e Our company implements the lifetime payable service if the product in malfunction has surpassed the warranty period e To the products with defect if it s in the period of warranty please fill in the form of warranty information correctly describe the trouble in details and provide original sales invoice or its copy e For the damage and loss which was caused by the user s specifically application factory won t bear any risk and responsibility The factory compensation made by breach of faith negligence or tortious won t exceed the amount of the products The factory won t bear any responsibility for the special unexpected and continue damage caused any other reasons e Our company has the final right of explanation for the above terms 2
51. re two choices ON clear alarm output the dome will stop OFF just clear alarm output RESET DELAY l set alarm reset delay the time 1 225s how long to relieve and run RESUME after the dome receives alarm message ALARM CONTACT set state of the relay N C often close the state N O often hold the state If setting as often closing the state the relay is in closing the state when there is no alarm to output when there is alarm to output the relay is in holding the state ALARM SETTING e ARM SETTING 2 Operate joystick and move the cursor to ALARM SETTING press OPEN to enter the menu alarm setting ALARM NUMBER alarm number is corresponding with 12 bits plug in the external switching board of the dome as below shows 001 priority is the highest 004 priority is the lowest The two lines alarm input at the same time the dome run alarm that the highest priority ALARM ACTION as current alarm input to run the action Choices for choosing as follow NONE none action SCAN PAT X run a pattern tour TOUR run tour PRESET call preset when the dome number is set as 1 to call preset 1 when the dome number is set as 2 to call preset2 ACTIVATE AUX as current alarm input to run alarm output or not NONE none alarm output AUX 1 the first alarm output AUX 1 the secondary alarm output BOTH two alarms output ALARM PRIORITY alarm priority can be defined as three grad
52. reset function is that dome stores current pan tilt angle zoom and other position parameters into the memory When necessary dome recalls these parameters and adjust camera to that position 4 Display current preset move the cursor to SHOW PRESET press OPEN the screen will display the current preset 5 Clear current preset move the cursor to CLEAR PRESET press OPEN the current preset is cleared 6 AUTO TRACKING Call preset to Set auto tracking ON OFF set as ON call the current preset to open auto tracking function set as OFF call the current preset to close auto tracking function Set as NONE call the current preset has no effect in auto tracking function 7 Edit current preset label move the cursor to EDIT PRESET LABEL press OPEN to enter into editing preset submenu system auto sets label as PRESET XX press OPEN to revise label 1 When running to program display clear preset and edit label should choose preset number at first 2 The label may set up to 16 characters and doesn t need editing characters Press OPEN continuously to jump over and use spacebar to replace the deleted characters When you finish to edit a character press OPEN to enter into the next editing character when you finish to edit the last character pressing OPEN to save Press CLOSE to exit Character of label is suitable for choosing as follow 0 9 A Z a space 3 As the submenu STATE in AUTO TRA
53. riority this function can be set OPERATION KNACKS Quality of photo relates to exposure amount that is to say how much light can make CCD receives legible image Exposure amount is relative to the time of lighten be up to shutter speed and the area of lighten be up to the size of iris The camera can automatically calculate suitable exposure amount according to brightness of scenery and CCD sensitivity in the situation that the exposure amountis certain SHUTTER shutter priority is to fix shutter speed the camera will auto decide to use how much iris IRIS iris priority is to fix the size of iris and auto decide to use shutter speed BRIGHT brightness priority is point that the camera TTL check the light directly and control the brightness of image S MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT J g CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER ON LINE SYNC N A WDR MODE N A ADVANCE SETTING1 ADVANCE SETTING2 BACK N ADVANCE SETTING AE MODE AUTO SHUTTER N A IRIS N A BRIG HT N A BW MODE R GAIN N A B GAIN N A HI RESO LU 108 BACK W Function setting 5 8 2 White balance mode System supports AUTO indoor mode INDOOR outdoor mode OUTDOOR auto track mode ATW single mode manual mode MANUAL and kinds of white balance modes etc Deta
54. s lower sensitivity and longer switch time In contrast the lower numerical value means higher sensitivity and shorter switch time Range 8 28 dB GAIN itis the maximum limit of auto gain Range 8 28 dB While under poor light situation the lower numerical value means dark amp less snowflake point image In contrast the higher num erical value means light amp more snowflake point image e EXPOSURE COMP Exposure compensation ON OFF MIRROR Image mirror ON OFF FLIP 180 Image flip function ON OFF SHARPNESS Image sharpness Range 00 15 PS SCAN Interlacing and Multi line scan OFF is Interlacing ON is Multi line STABLE ZOOM Stable zoom function ON to open OFF to close DNR Image denoising function Range 01 15 e VIDEO MODE Image input format Range 10801 60 10801 50 1080 30 1080P 25 720P 60 720 50 It will be valid after break off power 2 times 3 Press OPEN to save OPERATION KNACKS IR cut filter function uses color in day use black and white at night This function not only guarantees the quality of image but also saves the room of storage This function depends on the models and parameters of built in camera in dome if the camera doesn t have this function then it is invalid N A NOTICE 23 Function setting 2 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS E
55. t speed and time press OPEN the first dwell is activated tilt up down joystick to choose preset number the preset numerical value should be within 1 80 preset a tour can set up to 24 presets Press OPEN the cursor jump to the next dwell tilt up down joystick to choose current arrival preset speed total 8 level of speed increasingly from level 1 to level 8 Press OPEN the cursor jumps to the next dwell tilt up down joystick to set current preset maintaining time 60 seconds maximum If set the presets of the second line move the cursor to the second line press OPEN tocontinue edit press OPEN to save after setting press CLOSE to exit 6 Run tour Operate joystick move the cursor to RUN TOUR press OPEN to exit the menu it starts to run tour The system will leap over the preset automatically when the stay time of one item setting up on 0 The dome will not NOTICE run the tour of latter preset when preset or movement speed setting 0 29 Function setting 4 MAIN MENU 6 5 Zone A dome may be set up to 8 zones the regional scene can t be overlapped User will set label for each zone When setting ZONE LABEL as the dome will display zone label as it runs some zone It is convenient to know SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING the zone that the camera shoots by setting zone label ALARMS 5 EXIT 1 The system enters in
56. t when running the camera will shield the wobble picture and make the picture calm and smooth These function in the advance setting menu depends on the models and parameters of built in camera in dome if the camera doesn t have this function then this function is invalid The option is useless N A e NOTICE when the camera module has no such function MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP CLOCK SETTING COMM SETIING BACK EXIT CLEAR CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WNDOWS FACTORY DEFAULTS RESTART BACK EXIT tw System Setting 4 6 Clear 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursor to SYSTEM SETTING press OPEN to enter submenu 3 Operate joystick and move cursor to CLEAR press OPEN to enter submenu as left picture shows e CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS resume the factory default Run this function the camera parameter and system parameter will resume before production clear all windows and alarm setting Please be cautious to use this function RES
57. t or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursor to SYSTEM SETTING press OPEN to enter submenu 3 Operate joystick and move cursor to INITIAL INFO press OPEN to display initial information which as below the left picture shows Initial information includes S N of the dome soft edition Protocol Dome ID communication parameter System setting may change the numerical value of initial information MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP CLOCK SETTING COMM SETTING BACK EXIT DISPLAY SETUP DOME LABEL OFF PRESET LABEL OFF ZOOM LABEL OFF ZONE LABEL OFF DIR LABEL OFF TEMP LABEL OFF TIME LABEL OFF DATE LABEL OFF BACK Direction label tw System Setting 4 4 Display setup 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move cursorto SYSTEM SETTING press OPEN to enter submenu 3 Operate joystick and move cursor to DISPLAY SETUP press OPEN toenter display setup menu may setting the content of the display setup as follow DOME LABEL PRESET LABEL ZOOM LABEL ZONE LABEL DIRECTION LABEL TEMPERATURE LABEL TIME LABEL DATE LABEL 4 Taking displ
58. tected against extremes of pressure vibration humidity and other damage during storage and transportation 2 The dome should be shipped in parts disassembled as the original integrated packing during the transportation Damage caused by improper transportation is not within the warranty y Installation with care 1 Please refer to user manual when installation and sufficient strength of the wall or ceiling should be ensured 2 Power must be cut off when installation 3 Please handle with care do not squeeze and press structure parts which may cause mechanical damage 4 Down cover and lens of camera are precise optical items Please don t touch it directly to avoid scratch which will affect the image quality y Requirements to service personnel All the service work should be done by qualified technicians Do not disassemble the camera module y Environmental requirements Operation environment temperature 30 C 50 C Humidity lt 95 Air pressure 86 106Kpa Don t place lens of the camera to strong light objects like sun etc y Cleaning of down cover When the image is unclear or there is much dust on the down cover please use soft cloth to clean or use water to wash the down cover and then wipe up Precaution CS 2 1 Dome parameter Electrical Setting Power supply AC24V Baudrate RS485 2400 4800 9600 19200bps PELCO Kalate Phlips Diamond and Consumption 12W Protocol seventeen
59. to the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick and move the cursor to FUNCTION SETTING press OPEN to enter submenu FUNCTION SETTING 3 Operate joystick and move the cursor to ZONES press OPEN to enter PRESETS submenu as the left picture shows SCAN PATTERNS ZONES NUMBER TOUR e SET LEFT LIMIT ZONES SET RIGHT LIMIT TIME RUNNING CLEAR ZONE AUTO TRAC KING EDIT ZONE LABEL BACK EXIT Regard the left right limit as the demarcation line and set the middle 2 part as azone Various operational ways are the same as other settings in the J menu Therefore we don t explain it again ZONES ZONES NUMBER 1 SET LEFT UMIT SET RIGHTLIMIT CLEAR ZONE EDIT ZONE LABEL BACK EXIT 9 EDIT ZONE LABEL L ZONE1 BACK EXIT 30 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING ALARMS EXIT FUNCTION SETTING PRESETS SCAN PATTERNS TOUR ZONES TIME RUNNING AUTO TRAC KING BACK EXIT TIME RUNNING DAY SAT TIMECHANNEL 1 START TIME 00 00 END TIME 00 00 RUNNING TOURI BACK EXIT 02 Function setting 6 6 Time running User can set the time of preset scan tour and pattern 1 Call 95 preset or call 9 preset twice within 3 seconds to enter into the main menu 2 Operate the joystick and move the cursor to
60. to the target position then press OPEN to save Set right limit of the motion detection area operate the joystick to SET RIGHT LIMIT press OPEN operate joystick to the target position then press OPEN to save When the left amp right limit is set at the same point the speed dome will track the moving object with pan 360 area 5 Set upper limit of the motion detection area operate the joystick to SET UPLIMIT press OPEN operate joystick to the target position then press OPEN to save Set down limit of the motion detection area operate the joystick to SET DOWN LIMIT press OPEN operate joystick to the target position then press OPEN to save When the up amp down limit is set at the same point the speed dome will track the moving object within tilt 360 area 6 PARK TIME The setting allows PTZ to execute the next designated action after it is in idle state for 1 240 seconds on condition that it is under the Auto Tracking Mode The default setting is 000 which means no action A Underthe Auto Tracking Mode b TRACKING PARA PARK TIME which setting is not 0 c TRACKING TIME which setting is not none When reaching the above 3 conditions at the same time It will execute the function under TRACKING PARA PARK TIME 0005 PARK ACTION NONE but it won t execute the function under MOTION gt PARK TIME 000 PARK ACTION NONE When can t reach the above 3 condi tio
Download Pdf Manuals
Related Search