instructions for use replacing the protective window
Contents
1. REPLACING THE soy SureFire Surefire YSGG Delivery System YSGG Delivery System INSTRUCTIONS FOR USE Description The SureFire YSGG Delivery System is used Fig 1 A Distal end of fiber B Locking tab with WaterLase iPlus all versions WaterLase opening C Protective Window MDX and WaterLase MD Turbo D Locking tab Please note Once removed protective Installing the SureFire YSGG window is no longer usable Delive ry Syste m BIOLASE Inc 1 Remove the SureFire fiber from its 4 Cromwell packaging Irvine CA 92618 USA Fig 2 Push locking tab with pin or curette to 949 361 1200 NOTE Drape the SureFire fiber release the Protective Window 888 424 6527 around your neck as you prepare it biolase com for installation 2 Remove the protective silver cap from the proximal end which connects to the WaterLase of the Fiber MT Promedt Consulting GmbH Altenhofstrasse 80 D 66386 St Ingbert Germany 49 6894 581020 3 Remove the protective cover of the fiber Fig 3 Gently pull the released Protective mt procons com shaft at the distal end and hold it against Window from the fiber end any light source look into the proximal end of the Fiber it should glow yellow be flat and clean Replace the cover 0489 5201506 Rev B 4 Remove the black pastic cover and the internal red protective cap from the laser head and laser aperture save these for BIOLASE future use do not lose them Fig 4 Insert the new replac2. d two 2 replacement windows Protective Window Kit is available for re order PN 7200114 PRELIMINARY STEPS Before replacing the SureFire fiber Protective Window purge the handpiece and fiber of any residual water Power off the laser system Remove the handpiece from SureFire fiber NEVER REMOVE THE HANDPIECE FROM THE SUREFIRE FIBER WITHOUT PURGING PROPERLY Locate the distal end of the SureFire fiber Remove the Protective Window from the SureFire fiber Use a small pin such as a paper clip Fig 2A to push the tab of the Protective Window mounted into the metal housing located at the distal end of the fiber Fig 2B Gently pull the loosened Protective Window from the distal end of the Trunk Fiber Fig 3 Insert the replacement Protective Window Fig 4A by aligning the tab of the Protective Window Fig 4B to the rectangular opening of the metal bearing and gently insert into place The tab of the Protective Window should snap into the rectangular opening Fig 4C Discard of the burned damaged Protective Window in normal disposal bins Re attach the Handpiece and prime before use
3. ement Protective Window into fiber end until it locks in place 2015 BIOLASE Inc All rights reserved Surefire 5 Align the blue guide of the fiber connector 9 Carefully place the fiber with its protective WINDOW REPLACEMENT STEPS proximal end to the blue dot on the laser head interface Position the middle of the connector to the laser aperture and vertically push down gently as far as the connector will go WARNING DO NOT APPLY FORCE when installing the fiber Applying force may damage the laser head components Secure the retainer ring by turning it clockwise until it is snug Align the middle length of the fiber to the hook of the telescopic arm and push it in gently to secure it Remove the protective cover from the distal end of the fiber again and verify that itis clean and not damaged see Section 11 of WaterLase iPlus User Manual Maintenance and Troubleshooting NOTE Make sure the black retaining O ring on the fiber cable is on the front side of the hook to keep the cable in place cover or with the handpiece connected in the handpiece holder Troubleshooting Fiber Performance Please refer to WaterLase iPlus User Manual Section 11 for troubleshooting steps for the SureFire fiber Replacing the Protective Window SureFire Protective Windows are used in conjunction with SureFire YSGG Delivery system A SureFire fiber ships with a pre installed protective window an
Download Pdf Manuals
Related Search