USER`S MANUAL CCTV TesterPro
Contents
1. Measuring Ver STPV 1 32 Page 19 CCTV testerPRO Users Manual 3 OPERATING INSTRUCTION A DC Voltage Measuring WARNING You can t input the voltage which more than 660V DC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shock when measuring high voltage a Connect the black test lead to the COM jack and the red test lead to the V jack b Press D E to select U enter the DC voltage measurement Auto range by press key and Manual range by press SARA Manual range 0 000V gt 6 6V range 00 00V gt 66V range 000 0V gt 660V range 000 OmV gt 660mV range c Connect test leads across the source or load under measurement d You can get reading from LCD The polarity of the red lead connection will be indicated along with the voltage value NOTE 9 When only the figure OL is displayed it indicates over range situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position Page 20 Ver STPV 1 32 CCTV testerPRO Users Manual B AC Voltage Measuring WARNING You can t input the voltage which more than 660V AC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shock when measuring high voltage a Connect the black test lead to the COM jack and the re2. RS485 controlling data to help the technician to find out the problem Cable testing It is powerful in testing LAN cable measuring the connecting status displaying the sequence of connection and the NO of the LAN cable Multi interface and Multi baud rate Support RS232 RS485 and RS422 interface baud rate ranging from 150 600 to 19200bps Multi protocol Supports more than twenty PTZ protocols For example PELCO P PELCO D SAMSUNG etc PTZ address scanning search up the ID of PTZ camera Page 4 Ver STPV1 32 CCTV testerPRO Users Manual B Lithium Ion Polymer Battery 3 7V DC3000mAh The device employs advanced power control and protection circuit The device is high power efficient energy saving and environmental protection It can last 12 hours for normal use after charging for 4 hours 2 2 CCTV testerPRO Kits Professional design light and portability video display and data control are deliberately integrated which makes the instrument so simple practicable easy for use that the training is almost unnecessary for an operator to be skillful gn 1 CCTV testerPRO 3 LAN Cable Tester 5 BNC Cable 6 Safety cord 7 RS485 data cable 2 Power Supply 5V 2A 4 Lithium Ion Polymer Battery 8 Instruction Manual 2 3 Front Panel Ver STPV1 32 Page 5 CCTV testerPRO Users Manual C 7 aPTZ controller Video Setting Colorbar generator Cable tester m 6 Data moni
3. can get reading from LCD Ver STPV1 32 Page 25 CCTV testerPRO Users Manual 4 DC12V 1A power output Power the camera with DC12V 1A power output from the tester It is helpful for demo and testing where there is no power supply available V VIDEO IN VIDEO OUT p A El DC 12V 1A ge D OUTPUT Crise oe tting e Notice ae a Don t input any power into the DC12 1 A OUTPUT port of the CCTV tester to avoid destroy b Don t output this DC12V 1A power to the power input port of the CCTV tester to avoid destroy c When the requirement of the camera is higher than 1A the CCTV tester will enter protection mode Disconnect all the connections of the CCTV tester and then connect the CCTV tester with power adaptor to resume the CCTV tester 5 Audio input test Test the audio input from pickup devices Connect the tester and pickup device with the audio cable PE o Page 26 Ver STPV 1 32 CCTV testerPRO Users Manual 6 Specifications 6 1 General Specifications MODEL Signal mode Display LCD adjustment Video IN OUT Video Output Mode Level test Communication Compatible with more than 20 protocols such as PELCO D P Samsung PTZ Protocol nn Panasonic Lilin Yaan etc Baud Rate 150 300 600 1200 2400 4800 9600 19200bps Video Signal Generation Output one channel PAL NTSC colorbar video signal for testing Color bar generation monitor or video cable Digital mu
4. less than about 50 2 built in buzzer will sound e You can get reading from LCD NOTE If input open circuit or the circuit resistance measured is higher than 660Q then the figure OL will be display G Diode Testing a Connect the black test lead to the COM jack and the red test lead to the MH jack q b Press D E to select Y enter the diode testing c Connect test leads across to the anode the black lead to the cathode of the diode under testing Page 24 Ver STPV 1 32 CCTV testerPRO Users Manual d You can get reading from LCD NOTE The meter will show approximate forward voltage drop of the diode Ifthe lead connection is reversed only figure OL will be display H Capacitance Measuring WARNING To avoid electric shock be sure the capacitors have been discharged fully before measuring the capacitance of a capacitor a Connect the black test lead to the COM jack and the red test lead to the jack sala b Press D E to select T enter the capacitance measurement Auto range by press key and Manual range by press AGRO Manual range 0 000nF gt 6 6nF range 00 00nF gt 66nF range 000 0nF gt 660nF range 0 000uF gt 6 6uF range 00 00uF gt 66uF range 000 0uF gt 660uF range 0 000mF gt 6 6mF range 00 00mF gt 66mF range c Before connect test leads across two sides of the capacitor under measurement be sure that the capacitor has been discharged fully d You
5. our company Products certification C FE Page 30 Ver STPV 1 32
6. power off immediately and move away other cables connected M The tester should not be use in the environment with the flammable gas B Do not disassembly the instrument since no component inside can be repaired by the user If the disassembly is necessary indeed please contact with the technician of our company B The instrument should not be used under the environment with strong electromagnetic interference B Don t touch the tester with wet hands or waterish things B Don t use the detergent to clean and the dry cloth is suggested to use If the dirt is not easy to remove the soft cloth with water or neutral detergent can be used but the cloth should be tweaked sufficiently About digital multimeter M Before using you must select the right input jack function and range m Never exceed the protection limit values indicated in specifications for each range of measurement y When the meter is linked to a measurement circuit do not touch unused terminals Do not measure voltage 1f the voltage on the terminals exceeds 660V above earth ground M At the manual range when the value scale to be measured is unknown beforehand set the range selector at the highest position B Always be careful when working with voltages above 60V DC or 30V AC keep fingers behind the probe barriers while measuring m Never connect the meter with any voltage source while the function switch is in the current resistance capacitance diode contin
7. stop panning Page 1 8 Ver STPV 1 32 CCTV testerPRO Users Manual Press button the tester will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key to stop searching up Press ree manual single step decreasing button the tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will stop panning Press an button the tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop searching up Press manual single step incremental button the tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning Press the direction control button to adjust Speed Dome Camera Press button to quit from the address scanning function menu 3 10 Digital Multimeter PTZ controller Video setting Colorbar generator Cable tester Data monitor Device setting Address search reza a sla UTE Q gt 4 Function A Y Range 1 Function Button Auto range Data hold Relative measuring D G Function select SALES Manual range 2 SYMBOLS U DC Voltage Measuring U AC Voltage Measuring A DC Current Measuring A AC Current Measuring Q Resistance Measuring Continuity Testing Diode Testing F Capacitance
8. will damage the meter The maximum current of 10A socket is 10A over current will destroy the meter and will damage the operator E Resistance Measuring WARNING When measuring in circuit resistance be sure the circuit under test has all power removed and that all capacitors have discharged fully a Connect the black test lead to the COM jack and the red test lead to the Q jack lt b Press D Q to select Q enter the Q measurement Auto range by press key and Manual range by press AA Manual range connect the red lead to black leads will display the measure range 000 00 gt 6600 range 0 000 KQ gt 6KQ range 00 00KQ gt 66KQ range Ver STPV1 32 Page 23 CCTV testerPRO Users Manual 000 0 KO gt 660KO range 0 000 MO gt 6MQ range 00 00 MO gt 66MQ range c Connect test leads across the resistance under measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates overrange situation and the higher range has to be selected F Continuity Testing WARNING When testing the circuit continuity be sure that the power of the circuit has been shut down and all capacitors have been discharged fully a Connect the black test lead to the COM jack and the red test lead to the jack b Press to select enter the continuity test c Connect test leads across two point of the circuit under testing d If continuity exists i e resistance
9. Tilt the PTZ upward Leftward Enter the sub menu or select the parameter whose value will be changed Reduce the value of the parameter Pan the PTZ left Rightward Enter the sub menu or select the parameter whose value will be changed Add the value of the parameter Pan the PTZ right Downward Select the item which will be set or reduce the value of the parameter Tilt the PTZ downward Confirm Open Confirm the setting of parameters open the aperture Return Close Return or cancel while setting parameters of the menu close the aperture Near focus Focus the image nearby Far focus Focus the image faraway TELE zoom in the image WIDE zoom out the image Digital multimeter Ver STPV1 32 Page 7 CCTV testerPRO User s Manual 2 4 Side view 1831 3718V9 din Right Side O lt 4 nt voro ot Left Side 2 2 2 2 E 2 3 4 5 7 8 9 30 Page 8 Ver STPV 1 32 CCTV testerPRO Users Manual 2 5 Installing the Battery The tester has built in lithium ion polymer rechargeable battery The battery cable inside battery cabin should be disconnected for safety during transportation gt S Prior to the use of the instrument the battery cables inside the battery cabin should be well connected gt Usually it need not to disconnect the cable at the normal use pressing key continuously can power on or off the tester At the first time of use the batter
10. USER S MANUAL CCTV TesterPro O Ver STPV1 32 2009 5 CCTV testerPRO Users Manual Thank you for purchasing the CCTV security tester Please read the manual before using the CCTV testerPRO and use properly For using the CCTV testerPRO safely please first read the Safety Information carefully in the manual The manual should be kept well in case of reference Keep the S N label for after sale service within warranty period Product without S N label will be charged for repair service If there is any question or problem while using the CCTV testerPRO or damages occurred on the product please contact our technical Department Ver STPV1 32 Page l CCTV testerPRO Users Manual Table of Content 1 Safety Information a a a e ee nnen nana 3 2 Ed ele ARE RE 4 2 al LID IER aenescens een lensen sas a ae uee wanne nanne siamees nan cans S 4 2e CCTV teste PRO KITS ERA RER R SES sy RARES ARR RAR A SR ARE AR RSS AR RNA RONA 5 2 9 Frnt P aNg O e A 6 A O eng qin A E E enna 8 2 90 INSTAIING he Banery sse aE eee acs a E 9 3 Operation ete A A sen ey IA AiO 10 9 1 POWE ON Olfen se ne keker een se ne Ne denke nee este 10 3 2 Menu amp UNETIONSEEESESS SERRES ESS ER RRE seen sense 10 9 9 PTZ CONMOISTs sss e de Senden 12 aA VIADO SEH IG er ease a Ne MEET nana 15 3 9 Golorbar generator sAr nr AAA SRE ARR ARR RES 15 9 0 Cable testers iser densan dende PO edad annen 16 OF Dat
11. a monos testen eo 17 deo DEVICE SBN Gassen nennen RE ARR SRE ARR RE ARR ASS ARE ST RAA RAS RARES 17 39 Address SAGE Eee Apta nn e 18 2 10 Digital M ltimele rr SSSR EE SE ere 19 A DC12M POW T OUIDU SEEE ESS RARE RARE RAR ARR AN TS ARENA RTE ANA RR ARRE NASA NPA 26 D Audio input TEST En ER dann senen dan denten ace tense 26 6 Specifications ETES RARES SE STATE ARR RSS SRA DAA ten AR TARA TER Sei RRE TI ANARNSE 27 6 1 General specifications ARTS RASE ARTS ARTS e ARE RATER Rea 27 6 2 Multimeter specifications 28 Page 2 Ver STPV1 32 CCTV testerPRO Users Manual 1 Safety Information Notice M The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital gas station etc M To prevent the functional decline or failure the product should not be sprinkled or damped The exposed part of the tester should not be touched by the dust and liquid m During transportation and use it is highly recommended to avoid the violent collision and vibration of the tester lest damaging components and causing failure E Don t leave the tester alone while charging and recharging If the battery is found severely hot the tester should be powered off from the electric source at once The test should not be charged over 8 hours B Don t use the tester where the humidity is high Once the tester is damp
12. controller 1 PTZ controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position Baud Address Pan Speed Tilt Speed Set PS Go PS Page 10 Ver STPV 1 32 CCTV testerPRO User s Manual Video setting 2 Video setting Adjust the LCD brightness Contrast Color saturation Contrast Saturation Video Format and Video level testing Colorbar generator 3 Colorbar generator Output or receive seven different forms of video color bar to tester monitor cable or other equipment Cable tester 4 Cable tester Test LAN cable or telephone cable oth OU The connecting condition and the sequence of wires will be 2 7 displayed as well as the serial number of the cable tester kit Data monitor 7 5 Data Monitor Port 485 Baud 4800 Re ak 00 ah aa a A7 Captures the protocol from the controlling system and display AO 00 00 00 00 AF OF AO 00 00 10 00 40 AF SF aad HA a tanh RENTE command data It is helpful to debug and maintain RS485 AO 00 00 40 00 AF 4B AO 00 00 40 00 AF 4D AO 00 00 00 00 AF OF Device setting 6 Device setting en Set the parameters of the CCTV testerPRO Auto power off rompt soun on Language English ite Keypad tone Language Brightness Address search Brightness 7 Address search off Not saved En
13. cording Call preset 96 Run pattern 1 Call preset 97 Run preset tour 1 Page 14 Ver STPV1 32 CCTV testerPRO Users Manual Call preset 98 Run frame Scan Call preset 99 Run Auto scan Go PS pe Run Frame scanning Call the preset 098 point 098 Go PS 4 Run Auto scanning 099 Call the preset point 099 3 4 Video Setting User can customize the brightness contrast and saturation of the LCD according to the using environment the CCTV tester auto display the format PAL NTSC of video input and analysis the input video signal level Contrast Saturation a Press the or Lv key to select the parameter which we want to change the value b Press the lt or gt key to change the value Press ENTER key to save the change or press RETUR key to give up the change c The Video Format and Video Level will be displayed in the lower portion of the screen If there is no video signal at the Video IN port of the CCTV TesterPRO the type of NTSC or PAL and Video Level will not be displayed Depending on the type of camera connected to the CCTV testerPRO the Video Format will automatically change between NTSC and PAL and the Video Level will automatically change between IRE Institute of Radio Engineers and mV NTSC signals measured in IRE units PAL signals measured in mV The Video Level should be within the indicated range Levels that are too low will result in a dim picture with
14. d test lead to the V jack b Press D Q to select U enter the AC voltage measurement Auto range by press key and Manual range by press EENS Manual range 0 000V gt 6 6V range 00 00V gt 66V range 000 OV gt 660V range 000 OmV gt 660mV range c Connect test leads across the source or load under measurement d You can get reading from LCD NOTE 9 When only the figure OL is displayed it indicates over range situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position C DC Current Measuring WARNING Shut down the power of the tested circuit then connect the meter with the circuit for measurement a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack Ver STPV 1 32 Page 21 CCTV testerPRO Users Manual q b Press D G to select A enter the DC current measurement Manual range by press SANOS only manual range supply Manual range 0 000mA gt 6 6mA range 00 00mA gt 66mA range 000 0mA gt 660mA range 00 00A gt 10A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD The polarity of the red lead connection will be indicated along with the voltage value NOTE When only the figure OL is di
15. er PTZ cameras before searching up Otherwise all the PTZ cameras in the same system will pan at the same time Press keysto Device setting menu Device setting Prompt sound Language Brightness Address search Not saved Enter to apply ENTER p Press key to confirm after change Address search to on which add address scan sub menu Press to switch the sub menu as illustrated Note The system returns to OFF after shutdown and the Address search Protocol scan sub menu closes automatically Set ON again for next Port Baud use Address Press ser key to set protocol communication port Far Near Start search Wid Tele Adjust addr communication rate make them same as the PTZ camera Press on ar key the address values is constantly on the rise or decrease NEAR The tester will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key to stop searching up FAR The tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop searching up WIDE The tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning FAR The tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will
16. give up the change d Press SET key to exit the sub menu e Press POWER key to full screen the image A Protocol Select the protocol according to the protocol of the PTZ camera Up to 21 popular protocols are available like elco P Pelco D Samsung Yaan LiLin CSR600 etc B Port Select the communication port for the PTZ camera controlling RS232 422 485 C Baud Select the baudrate according to baudrate of the PTZ camera 150 300 19200bps D Address Set the ID according the ID of PTZ camera 0 254 E Pan Speed Set the pan speed of PTZ camera 0 63 F TiltSpeed Set the tilt speed of PTZ camera 0 63 G Set PS Setup preset position 0 128 a P T Z the camera to desired position b Press SET key to enter PTZ controller submenu c Move the yellow cursor to Set PS and then press or gt key to select the preset position number d Press ENTER key to complete preset position setting or preset RETURN key to give up preset position setting Tips Press or key to accelerate the value changing H Go PS Call the preset position 0 128 The PTZ camera will go to the desired preset position a Move the yellow cursor to Go PS and then press or gt key to select the preset position number b Press ENTER key to complete preset position calling or preset RETURN key to give up preset position calling Ver STPV 1 32 Page 13 CCTV testerPRO Users Manual Tips Press A or lt key to accelera
17. ies should be completely exhausted and then P recharged for 4 or 5 hours y The Charge Indicator lights red when charging the battery The charge indicator turns off automatically when the charging is completed A Notice When the Charge Indicator turns off the battery is approximately 90 charged The charging time can be extended for about 1 hour and the charging time within 8 hours will not damage the battery A The tester can work as usual while it is being charged however But the charging time will be extended Press the RESET key at the right of the instrument to restore the default settings when the instrument works abnormally Ver STPV1 32 Page 9 CCTV testerPRO Users Manual 3 Operation 3 1 Power on Continuously press at least 2 seconds to power on off the CCTV testerPRO When the CCTV testerPRO is powered on press MODE key the main menu will pop up PTZ controller Colorbar generator Cable tester Data monitor Device setting NO video input Address search 3 2 Menu amp Functions Press MODE key continuously or press the l key to select the function PTZ controller Video settings Colorbar generator LAN cable tester Data monitors Device setting and enter corresponding function setting sub menu Press SET key to set the parameters in function sub menu Note When the CCTV testerPRO is powered on it will return to the function which is being operated before it 1s turned off PTZ
18. ltimeter Voltage current resistance and capacitance measuring continuity Multimeter testing diode testing UTP CABLE TEST Test UTP cable connection status and display in the screen Read UTP cable test the number of the test box Ver STPV1 32 Page 27 CCTV testerPRO Users Manual Rechargeable After charging 3 4 hour working time lasts 12 hours Low Consumption Energy saving technology Working 10 C 50 C Temperature Working Humidity 30 90 Dimension Weight 176mmx94mmx36mm 340g 6 2 Multimeter specifications Counts 6600 6600 Conversion rate 3 times s Current modes for clamp meter with ZERO function DC Voltage 100mV AC Voltage 660mV Manual TK 1 5 6 660V 100mV DC Current 0 5 3 Page 28 Ver STPV1 32 CCTV testerPRO Users Manual AC Current 6 6mA luA 66mA 0 5 3 10uA 660mA 100uA Resistance 6600 0 8 5 0 10 6 6KQ 66KQ 0 8 2 660KQ 6 6MQ IKO 66MQ 1 2 5 10KQ Continuity Built in buzzer will sound if resistance is lower than 50 Q Diode ImV Display read approximate forward voltage ofdiode Ver STPV1 32 Page 29 CCTV testerPRO Users Manual Capacitance 660nF 7 3 5 8 6 6uF 660uF 100nF The data above is only for reference and any change of them will not be informed in advance For more detailed technical inquiries please feel free to call the Technical Department of
19. ne ae E HO AF with the RS485 or RS232 interface of the CCTV tester PRO o 00 00 oC AF In case of RS485 A to A B to B b Press SET key and then press 4 or WA key to select communication port according to the system connection Press SET key to save the change d Press ES or b74 key to select the baud rate according to the baud rate of controlling system and then press SET key to save the change and capture command data from controlling system e Press RETURN key to clear the screen Device setting 3 8 Device setting Set the parameters of the CCTV testerPRO rompi sound Language Brightness Address search Not saved Enter to apply Auto poweroff Setting the time of auto shut down Disable 5 10 60 Disable Disable the Auto poweroff function 5 means the CCTV will power off after 5 minutes when there is no any operation Keypad tone Open or close the beep of pressing keypad Language Select language of OSD menu Brightness Setting the brightness of OSD menu and background 0 7 Address search off on Open or close the PTZ address search Menu a Press A or key to move the parameter we want to change b Press Sl or to change the value c Press ENTER to save the change or press RETURN key to give up the change Ver STPV 1 32 Page 177 CCTV testerPRO Users Manual 3 9 PTZ address scanning Search up the ID of PTZ camera Note Please isolate the PTZ camera with oth
20. reduced dynamic range A Video Level that is too high will result in washed Ver STPV 1 32 Page 15 CCTV testerPRO Users Manual out pictures with decreased The CCTV testerPRO will display Normal when video levels are 1000mV 20 Exceed or Weak will be displayed when video level out of 1000mV 20 3 5 Colorbar generator Output video at any mode Colorbar generator Output or receive seven different forms of video color bar to test monitor video cable or other equipment a Press the or BS key to select the parameter which we want to change the value b Press the EN or key to change the value C Press ENTER key to save the change or press RETURN key to give up the change 3 6 Cable Tester Test LAN cable or telephone cable Connect LAN cable or telephone cable with the CCTV testerPRO and cable tester And then the connecting status cable type and the sequence of wires will be displayed as well as the serial number of the cable tester kit Cable tester NA Y NN Cable tester j Cable tester in Cable tester d ENE 11 1 3 2 2 Remote kit 3 YO MA Q AJ Cable Crossed ethernet Straight through Line Cross Line Open Line or Short Line Page 16 Ver STPV1 32 CCTV testerPRO Users Manual 3 7 Data monitor Baud 4800 Capture the command data from RS485 controlling system 40 ae AF O AF a Connect the RS485 or RS232 interface of controlling system O o
21. splayed it indicates overrange situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position 0 The maximum current of mA socket is 660mA over current will destroy the fuse and will damage the meter 0 The maximum current of 10A socket is 10A over current will destroy the meter and will damage the operator D AC Current Measuring WARNING Shut down the power of the tested circuit then connect the meter with the circuit for measurement a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack q A b Press D Q to select A enter the AC current measurement Manual range by press SALES only manual range supply Page 22 Ver STPV1 32 CCTV testerPRO Users Manual Manual range 0 000mA gt 6 6mA range 00 00mA gt 66mA range 000 0mA gt 660mA range 00 00A gt 10A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD NOTE 9 When only the figure OL is displayed it indicates overrange situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position 0 The maximum current of mA socket is 660mA over current will destroy the fuse and
22. te the value changing The way of calling the OSD menu and preset of the PTZ camera may vary with control systems from different manufacturers Please read the operation manual of control system manufacturer for details The way of calling OSD provided for reference is calling preset 64 a Move the yellow cursor to PTZ controller to enter PTZ controller mode b Press SET key to enter PTZ controller sub menu Press A or v key to move the yellow cursor to Go PS C Press lt or gt key to select the preset number 64 and then press ENTER key to call OSD menu of the PTZ controller Go PS OSD menu of dome 064 Call the preset point 064 OSD Menu of Dome For reference only MAIN MENU MAIN MENU DISPLAY SETUP CAMERA SETUP CONTROL SETUP CAMERA MASK SET PROGRAM PAL CAMERA CAM DEFAULT SET DOME RESET EXIT Display configuration Set camera parameters Set PTZ controlling Set privacy mask Set auto running functions PAL NTSC Switch Restore the default settings Reset the dome 1 2 3 4 5 6 7 8 9 D I AN A A U D Exit the main menu B Operate auto running functions by calling preset position effective for some brands of PTZ camera Call preset 33 Open Auto flip function Call preset 34 Reset zero point of PTZ camera Call preset 64 Enter the main menu of the PTZ camera Call preset 95 Enter the main menu of the PTZ camera or stop the PATTERN re
23. ter to apply Ver STPV1 32 Page 11 CCTV testerPRO Users Manual Address search 7 Address search Protocol Port Search the ID of PTZ camera Baud Address Far Near Start search Wid Tele Adjust addr Digital Multimeter 8 Digital Multimeter 0 000 V Digital Multimeter performs AD DC Voltage AC DC Current MS O D Resistance Continuity Capacitance and Diode test Auto 4 Function Manual Range Data hold Relative measuring AW Range 3 3 PTZ Controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position The following connections should be confirmed before use a The Video In interface of the CCTV testerPRO and the output interface of camera b Data A of the CCTV testerPRO and A of the PTZ camera or controlling device data B of the instrument and B of the PTZ camera or controlling device Note Don t connect communications interface with a circuit the voltage higher than 6V Page 12 Ver STPV 1 32 CCTV testerPRO User s Manual PTZ gt Il a Press SET key to enter the sub menu of PTZ controller ONO M rc b Press the A or key to select the parameter Port Baud which we want to change the value Address Pan speed Press ENTER k he ch RETURN TiltSpeed c Press ey to save the change or press Set PS Get PS key to
24. tor Device stting Address search Digital multimeter hit j L x y s P j Y 9 move set power f 1 8 Vip 4 T j lt sr 10 48 A Enter F j T j NEAR WIDE Return 46 17 J LA k CLOSE i j 11 A 20 A AS EEN 20 a pS I E cS The data reception indicator it lights red while the data is being received The data transmission indicator it lights red while the data is being transmitted The charge indicator it lights red while the battery is being charged As the charging is complete the indicator turns off automatically The display leon of battery electricity it displays the electric quantity Main menu it shows main functions of CCTV testerPRO Sub menu Shows and sets the values of functions Page 6 Ver STPV1 32 CCTV testerPRO User s Manual Long pressing it more than 2 seconds to turn on off the tester short pressing to turn on off the PTZ controller menu displaying Menu key it pops up the main menu constant press it or press the ES or LY key can shift between functions Setup key press it or press left or right key to enter sub menu to set the parameters of functions Upward Select the item which will be set or add the value of the parameter
25. uity otherwise 1t will damage the meter m Never perform capacitance measurements unless the capacitor to be measured has been discharged fully m Never measure any of resistance capacitance diode or continuity measurements on live circuits Ver STPV1 32 Page 3 2 CCTV testerPRO Users Manual Introduction The CCTV testerPRO is developed for the On Site installation and maintenance of video monitoring system It can be used for displaying video controlling PTZ generating images capturing data of RS485 and testing LAN cable etc Its functions easy operation and portability makes it simple for the CCTV technician to install and maintain CCTV system improving work efficiency and get the labor cost down 2 1 Features 3 5 TFT LCD 960 H x240 CV resolution Video Level testing video signals measured in IRE or mV DCI2V 1A power output for camera Audio input testing Digital multimeter voltage current resistance and capacitance can be tested continuity testing diode testing PTZ control Pan tilts the P T unit zooms in out the lens adjusts the focus aperture and sets and calls the preset position Video displaying Automatically adapts and displays the video format of NTSC PAL LCD Brightness Contrast Color Saturation are adjustable Video Generating The PAL NTSC multi system colorbar video generator seven system switchable transmit receive seven system colorful imagines Data analyst Captures and analyzes
Download Pdf Manuals
Related Search