Lava Lamp
Contents
1. Intertek al mark TEST SPECIFICATION Lava Lamp Electrical Lava Lamp COR PC ATION Product Protocol No TYCP LU003 US Version Prepared by Scope Sep 12 2011 Tiger Yang 1 of 6 Instructions to Vendors Dear Valued Vendor Product safety is a top priority at Taymark We with the assistance of Intertek a CPSC accredited third party testing partner or lab have identified the various rules and regulations as well as the necessary test requirements that we need to meet in our partnership to sell products in the United States This has been assembled into our required Test Protocol Each product that is supplied to us must comply with this Test Protocol and any required associated test protocol s identified within it You are required by the US Law to verify the products you provide to Taymark or any other customer marketing to children in the USA meet the required safety standards Likewise Taymark is required by US Law to assure that we have documentation to confirm that you have verified that your products meet the applicable safety standards Once you have verified that the product s you have supplied to us conforms to the corresponding Test Protocol s and the testing was conducted within the past twelve 12 months we ask that the appropriate representative from your company provide Taymark with the proper General Certificate of Conformity GCC2. close proximity to any mention of country other than country in which the article was manufactured or produced Must be visible at point of purchase 4 Use Labelling Visual Check Use care instructions that are clear and understandable shall be provided in language appropriate to destination countries 5 Verify Label Claims if any Visual Check Must comply with all claims 433528 _1 Intertek 2011 All Rights Reserved Intertek is the owner of the copyright in the material and intellectual know how presented No parts of this material may be reproduced adapted or distributed outside of your company without the consent of Intertek other than to the extent necessary to view the material Intertek al mark TEST SPECIFICATION Lava Lamp Electrical Lava Lamp COR PC ATION Product Protocol No Version Prepared by Scope TYCP LU003 US Sep 12 2011 Tiger Yang 3 of 6 Attribute Test Method Standard Requirement Limit 6 T Toxics in Packaging Toxics in Packaging Act Intentional introduction of any amount of lead mercury cadmium or hexavalent chromium in any packaging is prohibited Incidental presence of these metals is limited to 100 ppm total concentration of lead mercury cadmium and hexavalent chromium in any packaging In lieu of testing supplier may submit a Certificate of Compliance 7 FPlastic Bag Warning Based on Various State Laws Pl
3. contact 65K Wood 60K Plastic 25K Metallic 40 Durability of Switches In house method Switches shall continue to function correctly after 200 cycles of operations Remark Additional tests may be incurred subject to the final samples reviewed by Intertek 433528 _1 Intertek 2011 All Rights Reserved Intertek is the owner of the copyright in the material and intellectual know how presented No parts of this material may be reproduced adapted or distributed outside of your company without the consent of Intertek other than to the extent necessary to view the material
4. a California Proposition 65 t CPSIA Supplemental TYCP 00001 US Shall review against the CPSIA Supplemental and shall comply with all applicable requirements See CPSIA Supplemental Products Non toy Protocol posted at http Avww taymarkinc com t Children s Products Non toy TYCP 16026 US Shall comply with the applicable requirements See Children s Products Non toy Protocol posted at http Avww taymarkinc com Note Additional cost sample size amp TAT may be required if testing to 1 or more supplemental protocol is necessary Please refer to the above referenced supplemental protocol s for additional information Chemical Analysis 1 Lead Content in Paintand 16 CFR 1303 Shall not exceed 90ppm 0 009 by weight total lead Similar Surface Coating Scope Widened Document Check 2 TOne Time Use Products F P amp L Act Manufacturer packer or distributor s name amp address city state Fair Packaging and 16 CFR 500 amp zip Labeling Act OR Product Identification OR NIST Uniform Laws and All Other Products Uniform Regulations Handbook 130 Net quantity of contents shall be expressed in terms of weight or Packaging and Labeling mass measure numerical count or combination so as to give Regulations accurate information to facilitate consumer comparison U S and metric units 3 Country of Origin Marking 19 CFR 134 11 Shall indicate country of origin legibly permanently and in comparable size and
5. and the corresponding documentation that you used to support the GCC including where applicable and required the CPSC accredited third party test data For an example of an acceptable GCC please go to http www cpsc gov about cpsia faq elecertfag pdf Key t Any element on the attached form with the following symbol t is a Mandatory Requirement to which the product s or components of product s you supply to Taymark must conform You must perform the associated test s and provide Taymark with the test data to support the fact that the test s was were conducted and that the product s or components of product s meets the described requirements You are responsible for conducting the mandatory testing and you are responsible for any expenses incurred as a result of conducting the test s including without limitation the costs and expenses associated with providing any samples testing reporting and preparing the General Certificate of Conformity The symbol on the attached form indicates that additional charges may apply Taymark s preferred Accredited Third Party Testing Facility is Intertek If you choose to use Intertek to conduct the mandatory testing please reference Taymark and Taylor Corporation when submitting your requests for testing to Intertek as you may be able to take advantage of Taymark and Taylor Corporation s volume discount You may contact Intertek for a price quote and any additional information t
6. astic bags with a thickness less than one mil 1 1000 inch Statement if applicable New York Chicago having an opening size of five inches in diamerter or more must Massachusetts and Rhode have the following warning or an equivalent warning visible from Island State and City Laws each side of the bag If the total length and width is more than 40 modified inches this warning or an equivalent warning must repeat at 20 inch intervals and be visible on each side of the bag Warning To avoid danger of suffocation keep this plastic bag away from babies and children Do not use this bag in cribs beds carriages or playpens This bag is not a toy Massachusetts New York and Rhode Island provide minimum type size for the warning The following table sets forth type sizes that will satisfy all four state requirements Total Length and Width of Bag Size of Print 60 inches or more at least 24 point 40 to 59 inches at least 18 point 25 to 39 inches at least 14 point Less than 25 inches at least 10 point Virginia s law is intended for dry cleaning bags only and requires at least 36 point type 8 Safety Listing Mark NFPA 70 Shall have valid ETL UL or CSA listing or equivalent Verify listing by NRTL product directory with the sample s listing number and model number 9 FCC Rules Document Check Products shall have valid FCC report if operating frequency gt 9 a kHz for AC or operating frequency gt 1 705MHz for battery operated p
7. e cord length shall be a minimum of 9 feet 2 74 m and a maximum of 15 feet 4 57 m as measured from the exit of the furnishing to the attachment plug face For furnishings where the cord exits the furnishing at a height of 3 feet 0 9 m or less the cord length shall be a minimum of 5 feet 1 5 m and a maximum of 10 feet 3 05 m 433528 _1 Intertek 2011 All Rights Reserved Intertek is the owner of the copyright in the material and intellectual know how presented No parts of this material may be reproduced adapted or distributed outside of your company without the consent of Intertek other than to the extent necessary to view the material Intertek al mark TEST SPECIFICATION Lava Lamp GORP ATION Product Scope Electrical Lava Lamp Protocol No TYCP LU003 US Version Sep 12 2011 Tiger Yang 5of6 Attribute Test Method Standard Requirement Limit 22 Power Cord Cross Section Standard Measure The cross section area of conductor shall comply with Table 20 1 Area of Conductor mm of UL1581 for the AWG claimed 23 Plug Visual Check Plug shall be 3 wire grounding type or 2 wire polarized attachment plug 24 Stability Test UL 962 Cls 31 The unit shall not overturn when resting on a plane inclined at an angle of 10 degrees with the horizontal 25 Strain Relief Test UL 962 Cls 40 The strain relief means provided on power cord shall withstand fo
8. embly Instructions It shall also include instructions regarding the installation use safety and maintenance All accessories shall be described in the user s manual and provided with instructions for proper use 4 UPC code Actual Use Using a commercial available bar code reader to read the UPC code printed on the package artwork The code readout shall match with the number underneath Record the reading displayed on the reader 15 Parts Inventory Visual Check Shall meet label claims Electrical Safety ed 16 Packing No hazard when removing the packing 17 Workmanship external Visual Check Shall have no sharp points edges other than those required for function Shall have no components missing malformed and or fractured 18 Workmanship internal Visual Check Solder connections shall be secured Components shall be reliably mounted on PCB or other proper fixing 19 Mechanical Assembly Visual Check All mechanical parts shall be securely fixed and prevented from turning 20 Internal Wiring Visual Check Wireways shall not allow wires to come in contact with sharp points edges or moving parts 21 Power Cord UL 962 Cls 15 2 7 15 2 8 A flexible cord shall be at least Type SPT 2 SPE 2 or the equivalent Type SVT cord is equivalent when individual conductors are provided with supplementary insulation or spaced away from metal For furnishings where the cord exits the furnishing at a height greater than 3 feet 0 9 m th
9. est for glass part In house method The glass panel such as a window or wall shall be subjected to below test A solid steel sphere 2 inches 51 mm in diameter and weighing 1 18 pounds 0 54 kg is to fall as in a pendulum through a vertical distance of 20 inches to strike the surface The sample is to be supported by a furnishing or clamped in a position simulating intended use without restricting movement of components on the side opposite the impacts After test the panel shall not crack or break to result in leakage of inside liquid 32 Power Cord Cross Section Standard Measure The cross section area of conductor shall comply with Table 20 1 Area of Conductor mm of UL1581 for the AWG claimed 433528 _1 Intertek 2011 All Rights Reserved Intertek is the owner of the copyright in the material and intellectual know how presented No parts of this material may be reproduced adapted or distributed outside of your company without the consent of Intertek other than to the extent necessary to view the material Intertek al mark TEST SPECIFICATION Lava Lamp GORP ATION Product Scope Electrical Lava Lamp Protocol No TYCP LU003 US Version Sep 12 2011 Tiger Yang 6 of 6 Attribute Test Method Standard Requirement Limit 33 Security of Blade Test Each blade and pin shall be capable of withstanding a pull of 20 lbf for 2 minutes Displacement of
10. hey might need in order to conduct the required testing Additional Accredited Third Party Testing facilities can be found at htto Avww cpsc gov cgi bin labsearch Note Where there is no applicable US standard Intertek has chosen the most relevant International Standard to assess the product safety and performance For undated references the latest edition of the referenced document including any amendments applies 433528 _1 Intertek 2011 All Rights Reserved Intertek is the owner of the copyright in the material and intellectual know how presented No parts of this material may be reproduced adapted or distributed outside of your company without the consent of Intertek other than to the extent necessary to view the material Intertek al mark TEST SPECIFICATION Lava Lamp GORP ATION Product Scope Electrical Lava Lamp Protocol No TYCP LU003 US Version Sep 12 2011 Tiger Yang 2of6 Attribute Test Method Standard Requirement Limit Supplemental Protocol s Battery Operated Product TYCP PS001 Must all also test to the Battery Operated Product protocol if applicable Batteries TYCP PS002 Must all also test to the Batteries protocol if applicable AC Adaptor TYCP PS003 Must all also test to the AC Adaptor protocol if applicable tCA Prop 65 mandatory in state Intertek Protocol Consent Judgment of related court case based on Californi
11. more than 2 4 mm is not acceptable 34 Oooo y Performance Test Po 35 Functional Check Actual Use All the major features shall be matched with the installation and use instructions and claims made on the packaging with no inaccurate or misleading statements about the product or any other user friendliness problems 36 Ease of Installation Actual use Follow the instructions for assembly and disassembly the product and comment on the method of the installation Parts shall not be easy to break during normal use 37 Ease of Cleaning Actual use Follow the instructions to clean up the unit Comment on the method of cleaning 38 Range of operation The unit should operate within the voltage range of 106 127 volts 39 Continuous Operation Test In house method Place the unit on a softwood surface covered with 2 pieces of tissue paper set the unit to normal operation according to user manual continuously operate for 4 hours Shall not indicate safety issue fire risk or any other abnormality Polymeric material used as decorative parts shall not melt or deform in such a way as to interfere with normal operation of the product After the test check for excessive temperatures on supporting surface and all accessible surfaces In case of doubt measure the temperature rise and shall not exceed the following External surfaces 65K Surface intended to be grasped 20K Metallic 35K Nonmetallic Surface intended for momentary
12. r 1 minute without displacement a direct pull of 35 pounds 156 N applied to the cord with the connections within the furnishing disconnected At the point of disconnection of the conductors there shall be no movement of the cord indicating that connections were stressed 26 Accessibility of Live Parts UL 962 Cls 14 Openings in external enclosures shall be contructed located or baffled to prevent a standard probe from being inserted and touching live parts 27 Power Input Test UL 962 Cls 38 The power input to an appliance shall not be more than 110 percent of its marked rating 28 Dielectric Strength Test UL 962 Cls 43 The insulation and spacings of a furnishing shall withstand for 1 minute without breakdown the test potential specified in 43 3 For products employing double insulation the test potential shall be as specified in 43 4 29 Leakage Current Test UL 962 Cls 36 The leakage current of a cord connected appliance when tested shall not be more than a 0 5 mA for an ungrounded 2 wire appliance b 0 5 mA for a grounded 3 wire appliance that is easily carried or conveyed by hand 30 Grounding Ilmpedance UL 962 Cls 42 The impedance of two electrically interconnected electrical enclosures between the point of connection of the equipment grounding means and other metal parts that become energized is to be measured in accordance with 42 2 and 42 3 The impedance shall not be more than 0 1 ohm 31 Impact T
13. roduct 10 FCC marking and Visual Products shall have FCC required marking and instruction if instruction operating frequency gt 9 kHz for AC or operating frequency gt 1 705MHz for battery operated product 433528 _1 Intertek 2011 All Rights Reserved Intertek is the owner of the copyright in the material and intellectual know how presented No parts of this material may be reproduced adapted or distributed outside of your company without the consent of Intertek other than to the extent necessary to view the material Intertek al mark TEST SPECIFICATION Lava Lamp GORP ATION Product Scope Electrical Lava Lamp Protocol No TYCP LU003 US Version Sep 12 2011 Tiger Yang 4of6 Attribute Test Method Standard Requirement Limit 11 General Markings UL 962 Cls 54 55 The following markings shall be legible and readily visible during use Manufacturer s name trademark or etc Model number type reference or etc Electric ratings Date code 12 Cautionary Markings UL 962 Cls 54 58A The cautionary or warning marking requested by the standard intended to inform the user of a potential risk of fire electrical shock or injury to persons shall be provided 3 User Manual Important UL 962 Cls 59 64 Instructions and warnings shall be provided in the user manual Safety Instructions identifying reasonable foreseeable uses or misuses of the product Ass
Download Pdf Manuals
Related Search