Hybrid Seed Drill Operator`s Manual
Contents
1. Figure 22 Info screen controls On pressing the Setup Menu key the screen displayed in Figure 23 will be shown shortcut keys are now present along the bottom of the screen the corresponding buttons are positioned directly under each option e Calibration check button 2 Shortcut to manual calibration screen Tramline Setup Alarms Setup Data Logging and User setup 2 Drill config 3 Factory setup S LEN sd sa Diatnostics Variable Rate functions General PF setup Figure 23 Shortcut keys within setup menu The Calibration check option will be discussed in greater detail after the calibration procedure has been described The Tramline and Alarms Setup menus will be explained in the following sections for further information on the remaining Setup screens please consult the RDS manual February 2013 Page 20 of 52 CLAYDON Hybrid Hybrid Seed Drill In order to adjust the required tramline width or to turn the system off completely access the tramline Submenu by pressing the tramline shortcut key Figure 24 Setup Menu Tramline button Figure 24 Tramline shortcut key Once the tramline option key has been selected the tramline setup menu displayed in Figure 25 will be displayed Within this sub menu the spray width can be adjusted or tuned off by altering the target number of bouts Furthermore the tramline rhythm can also be altered between Symmetrical Asymmetrical left and Asymmetr2. Address Gaines Hall Wickhambrook Newmarket Suffolk CB8 8YA February 2013 Page 45 of 52 CLAYDON Hybrid Hybrid Seed Drill Table 1 disolayed where the slider on the metering unit should be positioned when sowing seed with a 3m Hybrid seed drill Firstly select the desired product and then select the closest required application rate Kg Ha the metering unit should then be opened to the slider setting displayed e g If wheat was required to be sown at 246 Kg Ha the slider on the metering unit would be set at 50 on a 3m drill highlighted below English Italian Dutch Spanish Swedish Danish German French Polish Wheat Gr no Tarwe Trigo Vete Hvede Weizen Bl Pszenica Rye Barley S gale Orzo Rogge Gerst Centeno Cebada Rag Korn Rug Byg Roggen Gerste Seigle Orge Zyto Jeczmien Oats Beans Avena Fagioli Haver Avena Frijoles Havre B nor Havre B nner Hafer Bohnen Avoine Haricots Owies Fasola Veldbonen Peas Pis lli Erwten Chicharos rtor rter Erbsen Poi Groszek Lupins Lupini Lupinen Lupino Lupine Lupiner Lupinen Lupine tubin Vetches V cce Wikke Vezas Vicker Vikker Wicken Vesce Wyki Maize Mais Mais Maiz Majs Majs Mais Mais Kukurydza Grass Erba Gras Hierba Gr sfr Gr sfr Grassamen Gazon Trawy Table 1 Metering unit slider positions for a 3m Hybrid Drill Oilseed Rape C lza Koolzaad Colza Raps Raps Raps Colz
3. CLAYDON Hybrid Hybrid Seed Drill Operator s Manual Original Instructions Contact Details Claydon Yield o Meter Ltd Gaines Hall Wickhambrook Newmarket Suffolk CB8 8YA Tel 44 0 1440 820 327 Fax 44 0 1440 820 642 Email info claydonadrill com www claydonatill com CLAYDON Hybrid Seed Drill Directive PI OVISIONS icin TT m d Airborne Noise EMISSIONS ssciixdninditumimek ot maps uade R u UEM Fai vene mas xdUm RU decades mancsitlimasesawuimexiiaedacadieles 7 Warnings and Cautions nenne ER REE REEEE EL nnns REESE nnns rris s sns ENES ES REESE REE ERR RR nsns aa 7 QUINONE OWS CW re EEN E EEA E a REEE EEA EEEE 8 POD WAO E E E 8 FEE EET EEE EEE OE E E 8 Connecting the Drill to the Tractor eeeeessssssseeseseeeeeeeeennnn nnne nnne nnn rn nenne nnns annis 9 TEAMSOON AOU Nr 12 PVT 2E RR IS NENNT RTT RR 12 Radar Recalibration Process cccccssssseccecceeseeceeccaeeeeceeeeeeseeeeecsaeseeceeseeaseceeessaaseceesssaeeeeessaeaeeeeeeeas 13 Changing releasing the Stone Release Pressure sees nennen nnn 15 Wing Balancing Kit 6m Machines Only sssesssssssssssseseeeeee nennen nennen nennen nnns nnn nnns 16 Setting Up and Calibrating the Seed System cccccccesceeccceeseeeeeeeeeeeeeeeeeaeeeeeeeseaseeeeessea
4. Gazon Trawy Travni February 2013 Koolzaad Grassamen Grassamen Grassamen Grassamen Red Clover Trifoglio Rosso Rode Klaver Tr bol Rojo R dkl ver R dkl ver Rotklee Tr fle Rouge Red Clover Trifoglio Rosso Rode Klaver Tr bol Rojo R dkl ver R dkl ver Rotklee Tr fle Rouge English Italian Dutch Spanish Swedish Danish German French Polish erven Jetel erven Jetel English Italian Dutch Spanish Swedish Danish German French Polish Czech Grass rba Gras Hierba Gr sfr Gr sfr rba Gras Hierba Gr sfr Gr sfr Gazon Trawy Travn Gazon Trawy Travn Red Clover Trifoglio Rosso Rode Klaver Tr bol Rojo R dkl ver R dkl ver Rotklee Tr fle Rouge Red Clover Trifoglio Rosso Rode Klaver Tr bol Rojo R dkl ver R dkl ver Rotklee Tr fle Rouge Koniczyna Czerwona Koniczyna Czerwona Koniczyna Czerwona Koniczyna Czerwona erven Jetel erven Jetel Page 52 of 52
5. Front indicated the three point linkage end of the machine Rear indicates the machine end on which the steps are mounted Left indicated the left of the machine as you look at the machine from the rear Right indicates the right of the machine as you look at the machine from the rear Figure 1 Overall view On taking delivery check for any possible damage that could have occurred during transit Remove all loose parts harrow tines level boards etc that may have been stored in the seed hopper for transit and fit to the machine February 2013 Page 8 of 52 CLAYDON Hybrid Hybrid Seed Drill A tool box is supplied and contains the following items 1 x Quick Release Tool 1 x Spare Front Tine Part No SBA1 52 1 x Pack of Shear Bolts Shear Bolt version machines only 2 x M16 U Bolts for Tine 1x Control Unit and Cable 1 x Control Unit Mounting Bracket and Bolts 1 x Tractor Power Cable 1 x Claydon Instruction Manual 1 x Claydon Instruction DVD x Parts Catalogue 1 x Calibration Scales 1 x RDS Operation manual 1 x Fan 1 ISO with 18L male thread Please contact Claydon if any are missing The Claydon Drill can be mounted onto any CATIIIN or CATIVN compatible three point linkage with the linkage pins supplied and CATIII balls not supplied Connect the main power cable supplied with the RDS Artemis Control Unit directly to the battery terminals Run the cable to the tractor cab by a safe rout
6. German French Polish Maize Mais Mais Maiz Majs Majs Mais Mais Maize Mais Mais Maiz Majs Majs Mais Mais Maize Mais Mais Maiz Majs Majs Mais Mais Maize Mais Mais Maiz Majs Majs Mais Mais Kukurydza Kukurydza Kukurydza Kukurydza Kuku ice Kuku ice Kuku ice Kuku ice Page 51 of 52 CLAYDON Hybrid English Italian Dutch Spanish Swedish Danish Gr sfr Gresfro Hybrid Seed Drill Grass Erba Gras Hierba Gr sfr Gresfro Grass Erba Gras Hierba Gr sfr Gresfro Grass Erba Gras Hierba Gr sfr Graesfro Grass Erba Gras Hierba German Grassamen Grassamen Grassamen Grassamen French Polish Czech Gazon Trawy Travn Gazon Trawy Travn Gazon Trawy Travn Gazon Trawy Travn Once the Cal Factor value has been obtained from the calibration check procedure the figure can then be compared with the results below all the values on this page apply to small seeds only English Oilseed Rape Oilseed Rape Oilseed Rape Oilseed Rape Colza Colza Koolzaad Colza Colza Koolzaad Colza Colza Koolzaad Colza Italian Dutch Spanish Swedish Danish German French Polish Colza Grass Erba Gras Hierba Gr sfr Gresfro Grass Erba Gras Hierba Gr sfr Gresfro English Italian Dutch Spanish Swedish Danish German French Polish Czech Gazon Trawy Travni
7. Seed depth 2 Original soil level Figure 43 Seed depth To ensure the correct driling depth has been achieved the depth of the arills A Shares relative to the grounds surface should be examined Figure 44 displays the recommended A Share depth for Oilseed rape shoulder of A Share should coincide with ground surface and Wheat top of A Share should coincide with ground surface Oilseed rape Wheat l Leading tine 2 A Share depth OSR 1 Leading tine 2 A Share depth Wheat Figure 44 Recommended A Share depth for OSR and Wheat February 2013 Page 31 of 52 CLAYDON Hybrid Hybrid Seed Drill Once the seed depth is set you can set the depth of the front tine as a guide the front tine should be set to approximately 120 150mm deep for Oilseed rape n 100mm for Cereals m 125mm for autumn Beans and Maize 75 100mm for Spring Beans he front tine is adjusted by simply removing the pin sliding the tine to the required depth position hole Figure 45 and reinserting the pin l Remove pin and slide tine up or down to required position 2 Wear hole Figure 45 Setting front tine depth The top hole should not be used on brand new tines it is only to be used once the tine has begun to wear Do not operate the front tine deeper than 150mm The Level Board also known as Batter Board or Ski Board should be set up to drag along the top of the ridges with little down pressure The down pressure can eith
8. Swedish A Artor Danish Arter German Erbsen French Polish 0 475 570 428 356 285 February 2013 Peas Piselli Erwten Artor rter Erbsen Peas Piselli Erwten Artor Arter Erbsen Hybrid Seed Drill English Lupins Lupins Lupins Lupins Italian Lupini Lupini Lupini Lupini Dutch Lupinen Lupinen Lupinen Lupinen Spanish Lupino Lupino Lupino Lupino Swedish Lupine Lupine Lupine Lupine Danish Lupiner Lupiner Lupiner Lupiner German Lupinen Lupinen Lupinen Lupinen French Lupine Lupine Lupine Lupine Polish tubin tubin tubin tubin 184 0193 232 174 145 116 0213 256 192 160 128 0233 280 210 175 mo 0254 305 229 191 152 0275 330 248 206 165 0295 354 266 221 177 0315 378 284 236 189 0335 402 302 2351 20 0 355 426 320 266 213 0 376 452 339 282 226 0396 476 357 297 238 0 416 500 375 312 250 0 436 524 393 327 262 English Italian Dutch Spanish Swedish Danish German French Polish Vetches V cce Wikke Vezas Vicker Vikker Wicken Vesce Wyki Vetches V cce Wikke Vezas Vicker Vikker Wicken Vesce Vetches V cce Wikke Vezas Vicker Vikker Wicken Vesce Vetches V cce Wikke Vezas Vicker Vikker Wicken Vesce Wyki English Italian Dutch Spanish Swedish Danish
9. correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Check sensor on metering unit Signs of mechanical damage to encoder or cabling on motor 3way connector between motor and harness is correct Wiring between 3way connector and module connector is correct February 2013 Page 42 of 52 gear ES CODE Hif ga 1g ES CODE Hic aa mue E maag HiF Bg a4 E WES HIT February 2013 mass perz Hybrid Seed Drill Left motor control module is offline Right motor control module is offline Seed Motor Control Module is offline Fert motor control module is offline Tramline module is offline Seed motor module temperature foo hot Module temperature has exceeded the value programmed Check wiring between way connector and module connector on MCM harness If alarm M 3 L amp H 1 L also shown then check between 50way D connector on back of PSi and both way amp 4way of instrument harness Check wiring between way connector and module connector on MCM harness If alarm L 7 SU amp H 1 L also shown then check between 50way D connector on back of PSI and both 6way amp 4way of instrument harness Check wiring between 6way connector and module connector on MCM harness If alarm H 1 L also shown then check between 50way D connector on back of PSI and both way amp 4way
10. of instrument harness Check wiring between way connector and module connector on MCM harness If alarm L 4 R amp H 1 L also shown then check between 50way D connector on back of PSi and both way amp 4way of instrument harness Check module has got power from main battery power cable Check wiring between 4way connector and module connector on HBM harness If alarm L 4 R also shown then check between 50way D connector on back of PSi and both way amp 4way of instrument harness Motor speed very low Excessive load applied to motor which for a prolonged time has caused the high module temperature Page 43 of 52 Hybrid Seed Drill Seed motor B2 56 ES CODE uis module temperature shutdown Module temperature has exceeded the value programmed Seed motor module overload shutdown Motor current requirement exceeded so module shutdown and motor operation inhibited 1119 Sv Forward Speed MEM HSSF Failure Seed amp Fert Cats seen Forward Speed miia H5LR Failure Left amp Right 1283 Ew X M Motor has Stalled CODE Motor speed very low Excessive load applied to motor which for a prolonged time has caused the high module temperature Motor stalled Excessive drag on the metering unit requiring high motor current Check wiring of forward speed in alarmed connection box Check for continuity between pin 2A on MCM 1 white wire and pin 2A on MCM 2 Check
11. to 110 bar 1600 psi from the factory In the event that it is higher or lower please call Claydon for guidance on how to adjust it see Contact Details on front cover When the required pressure is met turn the tap to the off position at a right angle to the direction of the hose Figure 14 Figure 14 Tap in closed position The Wing Balancing Kit spreads the weight of the chassis and the full hopper over the whole width of the drill and not just in the centre section In this way it allows the wings to float and follow the contours of the ground To ensure the kit is working correctly the operator should operate the tractor spool valve to lower the wings spool needs to be set up so pushing the controller forward lowers the wings the spool must also have a float position once the pressure has reached 10 bar 145 psi the operator needs to push the controller fully forward into float to allow excess pressure to return to the tractor in the event of the drill hitting a large obstacle and the wings raising beyond their pre set limit The location of the pressure gauge can be seen in Figure 15 1 Wing balancing pressure gauge 2 Stone protection pressure gauge Figure 15 Pressure gauges for Wing Balancing Kit and Stone Protection Unit February 2013 Page 16 of 52 Hybrid Seed Drill This is a brief guide to using the RDS Artemis Control Unit while in work The RDS manual supplied with the machine should
12. unit is not going around Left seed metering unit is not going around Seed only arill with 2 motors each driving 1 metering unit Right seed metering unit is not going around Seed only arill with 2 motors each driving 1 metering unit Fert metering unit is not going around Seed amp fert drill with 2 motors each driving metering unit Is seed metering unit rotating when motor rotates Sensor amp target functioning and correct PPR value programmed correctly wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Check sensor on metering unit Is seed left metering unit rotating when motor rotates Sensor amp target functioning and correct PPR value programmed correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Check sensor on metering unit Is right metering unit rotating when motor rotates Sensor amp target functioning and correct PPR value programmed correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Check sensor on metering unit Is fert metering unit rotating when motor rotates Sensor amp target functioning and correct PPR value programmed correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is right Check sensor on metering unit February 201
13. 3 Page 41 of 52 M 3 LFH M 3 SLH M 3 RSH H3 13 Ely i mind 2LFH I a M es A E FAIL LEFT 8313 Ey MEUS M 3 SLH B 14 E CODE 2 E3H FAIL RIGHT 18 15 Ex COLE ic O Hybrid Seed Drill Left fert metering unit is not going around Seed amp fert drill with 2 motors each driving 2 metering unit Left seed metering unit is not going around Drill with 1 motor driving 2 metering units Right seed metering unit is not going around Drill with 1 motor driving 2 metering units Motor speed signal from seed motor not being received Motor being operated and pulses received from shaft confirmation sensors but no motor speed signal Is fert left metering unit rotating when motor rotates Sensor amp target functioning and correct PPR value programmed correctly Wiring between sensor and connection box Is correct Wiring between connection box and CAN module is correct Check sensor on metering unit Is seed left metering unit rotating when motor rotates Is drill being operated at 2 width Sensor amp target functioning and correct PPR value programmed correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Check sensor on metering unit Is seed right metering unit rotating when motor rotates Is drill being operated at 2 width Sensor amp target functioning and correct PPR value programmed
14. D ENSURE A SUBSTANTIAL PROP IS POSITIONED SAFELY UNDER THE DRILL PREVENTING IT FALLING UNDER ITS OWN WEICHT e Speed Loc tool 2 A Share Speed Loc adapter EYE PROTECTION MUST BE WORN Figure 54 Changing shares NEVER HIT THE TUNGSTEN CARBIDE TILES WITH A HAMMER WEAR GLOVES AND SAFETY GLASSES WHEN WORKING WITH THE TUNGSTEN CARBIDE PARTS NEVER HIT THE LOCKING PIN WITH A HAMMER AND PUNCH OR ANYTHING SIMILAR AS THIS WILL DAMAGE THE SPRING To remove and refit the seed boot undo the nuf remove the bolt and let the boot drop out of the boot holder place new boot in holder and push bolt back into place retighten the nut NB Use 9 16 spanners Figure 55 Changing seeding boots February 2013 Page 3 of 52 Hybrid Hybrid Seed Drill 11 28 E CODE L 3 35 11 24 E MESS L SFS 1121 ES CODE LSL February 2013 High forward speed Forward speed exceeds the maximum calculated and displayed on the RATE screen Low fan speed Fan speed is below the low alarm value programmed High fan speed Fan speed is above the upper alarm value programmed Seed level is low Seed only or Seed amp Fert drill 1 metering unit per product Fert level is low Seed amp Fert drill only 1 metering unit per product Seed level left is low Seed only arill with 2 metering units independent left amp right level sensors Target application rate is as required Calibration fa
15. Zapylaczka hnojivo Lupine Vesce Mais tubin Wyki Lupina Vikve Gazon Colza Trawy Travni Trefle Rouge Koniczyna Czerwona Cerveny Jetel Gazon Navet Trawy Rzepa Travni Turin Polish Czech Jeczmien Owies Je men Oves Fasola Fazole Groszek Hr ek Kukurydza Kuku ice February 2013 Page 49 of 52 CLAYDON Hybrid Hybrid Seed Drill Once the Cal Factor value has been obtained from the calibration check procedure the figure can then be compared with the results below all the values within this section apply to large seeds only Firstly select the correct product large seeds continue on following page then locate the nearest application rate Kg Ha followed by the drill width The corresponding Cal Factor Kg rev can then be compared to the value displayed on the Artemis control box Although the values may not be an exact match the figures should be within the same region if not a recalibration may be required e g If a 3m Hybrid drill containing Wheat was calibrated to apply 121Kg Ha the Artemis unit would display a Cal Factor of approximately 0 101 Kg rev shown below English Wheat Wheat Wheat Wheat English English Barley Barley Barley Barley English English Beans Beans Beans Italian Gr no Gr no Gr no Gr no Italian e e e Italian Orzo Orzo Orzo Orzo Italian Italian idli Fagi li Fagi li Fagi li Dutch Tarwe Tarwe Tarwe Tarwe Dutch Dutch Gerst Gerst Gerst Gerst Dutc
16. a Rzepak Red Clover Trifoglio Rosso Rode Klaver Tr bol Rojo R dkl ver Rodklover Rotklee Trefle Rouge Koniczyna Czerwona Grass Erba Gras Hierba Grasfr6 Gresfro Grassamen Gazon Trawy Turnip Rapa Knolraap Nabo Kalrot Majroe Rube Navet Rzepa Czech P enice Zito Je men Oves Fazole Hr ek Lupina Vikve Kuku ice Travn epka erven Jetel Travn Turin Relative density 0 77 0 74 0 68 0 5 0 85 0 81 0 76 0 83 0 79 0 36 0 77 0 74 0 68 0 5 February 2013 Page 46 of 52 CLAYDON Hybrid Hybrid Seed Drill Table 2 displayed where the slider on the metering unit should be positioned when sowing seed with a 4m Hybrid seed drill Firstly select the desired product and then select the closest required application rate Kg Ha the metering unit should then be opened to the slider setting displayed e g If wheat was required to be sown at 241 Kg Ha the slider on the metering unit would be set at 65 on a 4m drill highlighted below Table 2 Metering unit slider positions for a 4m Hybrid Drill English Wheat Rye Barley Oats Beans Fertiliser Peas Lupins Vetches Maize Grass Oilseed Rape Red Clover Grass Turnip Italian Grano Segale Orzo Avena Fagioli Fertilizzante Piselli Lupini V cce Mais Erba Colza Trifoglio Rosso rba R pa Dutch Tarwe Rogge Gerst Haver Veldbonen Meststof Erwten Lupinen Wikke Mais Gras Koolzaad Rode Klaver Gras Knolraap Spanish Trigo Centeno Cebada Avena Frijoles Fertilizante Chicharo
17. and all electrical connections are correctly installed Connect the two black round connectors to power up the Control Unit If the Control Unit is beeping with a forward speed alarm this can be turned off by pressing the Metering On Off button To enable seeding press the Metering On Off button again The toggle switch comes attached to its mounting plate Position the mounting plate to straddle the upright plate of the headstock The drill should be placed on a solid surface while attached to the tractor The toggle switch bracket should now be slid up or down the headstock plate until the switch is in the neutral position in the middle and just touching the bottom of the top link Now tighten the pinch bolts up to lock the bracket into place The purpose of the switch is to turn the seeding system on and off With the drill in the working position and at drilling depth there should be approximately 5mm clearance between the switch and the underside of the top link Top link pin Area cut out switch Figure 28 Spring toggle switch shown in work position The seed level sensor can be set in three positions for different seed rates the upper for high seed rates the middle setting for medium seed rates and the lower position is ideal for low seed rates i e Oilseed rape l Setting for low seed rates Current position 2 Setting for medium seed rates 3 Setting for high seed rates To adjust the hopper level sensor setting Fro
18. ans Fertiliser Peas Lupins Vetches Maize Grass Oilseed Rape Red Clover Italian Gr no Segale Orzo Avena Fagioli Fertilizzante Piselli Lupini V cce Mais Erba Colza Dutch Tarwe Rogge Gerst Haver Veldbonen Meststof Erwten Lupinen Wikke Mais Gras Koolzaad Spanish Trigo Centeno Cebada Avena Frijoles Fertilizante Chicharos Lupino Vezas Ma z Hierba Colza Tr bol Rojo Hierba Nabo Swedish Vete R g Korn Havre B nor G dningsmedel Artor Lupine Vicker Majs Gr sfr Raps R dkl ver Gr sfr K lrot Danish Hvede Rug Byg Havre Bonner G dning rter Lupiner Vikker Majs Gr sfr Raps R dkl ver Gr sfr Majroe German Weizen Roggen Gerste Hafer Bohnen D nger Erbsen Lupinen Wicken Mais Grassamen Raps Rotklee Grassamen R be French Bl Seigle Orge Avoine Haricots Engrais Poi Lupine Vesce Mais Gazon Colza Trefle Rouge Gazon Navet Polish Pszenica Zyto Jeczmien Owies Fasola Zapylaczka Groszek tubin Wyki Kukurydza Trawy Rzepak Koniczyna Czerwona Trawy Rzepa Czech P enice Zito Je men Oves Fazole hnojivo Hr ek Lupina Vikve Kuku ice Travn epka erven Jetel Travn Turin Relative density Kg l 0 77 0 74 0 68 0 5 0 85 1 0 81 0 76 0 83 0 79 0 36 0 77 0 74 0 68 0 5 Drillwidth m as as as as as as as 48 48 48 as as Grass Turnip Trifoglio Rosso Erba Rapa Rode Klaver Gras Knolraap February 2013 Page 48 of 52 CLAYDON Hybrid Hybrid Seed Drill Table 4 displayed where the slider on the metering unit should be posit
19. ary 2013 Page 27 of 52 CLAYDON Hybrid Hybrid Seed Drill 1 Screen displayed on Artemis control box 2 Enter actual weight dispensed making sure 3 Once the weight is entered and the curser after calibration button has been pressed the correct units are highlighted press Enter has stopped flashing press Enter again ENTER WEIGHT uv LA Weiner ENTER fota a s ENTER R TORON C j Ne m FOKON E Nee WEIGHT DISPENSED p DISPENSED j DISPENSED Wu 2 HERE PAs o HERE Cn ON x n GRON C wm 1 950 Kg s or Gram s selected by pressing these button s 1 User setup C Old ks reu 0 308 2 Drill confia f ONOMC pect GS 3 Factory setup 80 17 dus i 4 Diasnostics S 7 8 7 j Max SP 25 0 km hr S General FF setup An e 5 Once the stored values are accepted and saved the Setup menu will be displayed 4 This screen will be displayed once the weight has been entered Press the Enter key once more to accept and store the new values Figure 37 Calibration process on Artemis control box February 2013 Page 28 of 52 CLAYDON Hybrid Hybrid Seed Drill To ensure the metering unit has been calibrated correctly it is possible to perform a calibration check by observing the Cal Factor This is checked by firstly pressing the Setup menu button from the Setup menu the calibration check button should then be pressed Figure 38 l Calibration
20. ate position The stickers must not be removed ES N ra m Meaning of warning symbols Read the operating manual carefully Prior to operating the machine the manual must be read fully and understood Special attention should be applied to the Warnings and Cautions section Do not stand between the tractor and the machine Standing between tractor and the arill is especially prohibited during coupling and uncoupling February 2013 Page 4 of 52 CLAYDON Hybrid Hybrid Seed Drill Riding on the machine is prohibited Serious or fatal injury can occur as a result of riding on the machine Proceed with care in the event of leaking hydraulic fluid Defective hydraulic hoses or incorrectly seated hydraulic couplings can trigger unpredictable machine movements and cause Injury Keep clear of slewing range There is an extreme risk of injury from slewing or folding machine parts Do not pressure wash locality Electronic components will be seriously damaged If event occurs Machine noise levels Noise level of fan during operation decibels Wear gloves Gloves must be worn when handling product or preforming maintenance tasks Risk of crushing Gaps between components may become smaller or disappear completely Caution danger of explosion Disassembly and re pair work must be completed by a qualified person only Accumulators contain pressurised gas and oll Retighten all nuts All nuts
21. ated would pass through the metering system per revolution and what was actually weighed With the seed hopper empty follow the method below to calibrate your drill 1 At the metering unit wind in the handle until it is fully closed the O position 2 Turn red lever to intersect drive shaft key Turn red lever so that it is not in The drive shaft way see Figure 35 1 key way see Figure 35 2 3 Fan deflector lever needs to be set Fan deflector lever needs to be set parallel perpendicular to pipe direction Figure 36 1 to pipe direction Figure 36 2 4 If necessary ensure that the white and red gears are aligned by pushing the white button so that the red gear will insert into the grey white gear and push into place This setting should always be used and gives high speed gearing at all times 5 Wind out handle to about 15 on slider 20 Wind out handle to about 80 on slider The max see Figure 34 For more comprehensive handle may be wound out further to achieve details on slider positions consult Appendix C higher speeds Figure 34 For comprehensive at the rear of the manual details on slider positions consult Appendix C 6 Undo the U bracket and release the 90 bend Place a bucket under the metering unit prime the metering unit by pressing the white button and hold for three seconds to start the metering motor this ensures the unit is full of seed prior to an automatic calibration Press the white button agai
22. be read for full instructions The Artemis display has 3 main screens which can be selected using the arrow buttons on the right hand side of the display The screens are Main Rate and Info l Press to select Main screen 2 Press to select Rate setting screen 3 Press to select Info page 4 za fi mere IE 6 E E Figure 16 Screen selection An overview of the Artemis Main screen can be seen in Figure 17 this screen will be displayed when the control box is first turned on and whilst in work Figure 18 displays the navigation buttons located on the Artemis box Q l Time N 2 Area cut out status V In work X Out of work 3 Tramline number 4 Fan speed rom 5 Manual Override Seed Metering On Off Forward speed 7 Seedrate ION d D ON Y Ss LAI lt j N sh Ilo v Figure 17 Main screen indications February 2013 Page 17 of 52 CLAYDON Hybrid Hybrid Seed Drill Setup Menu Go to INFO Screen Go to RATE Screen Go to MAIN Screen currently disolayed Number Key Pad Power On Off Button Pre Start starts metering unit prior to moving forward 8 Manual Override Seed Metering On Off 9 Auto Tramline advance On Off 10 Tramline number nudge CS tramlines come on when on WEE ee 4 highest number 5 of 5 in this 11 Backspace key 9 O 2 12 Enter Key Figure 18 Main screen controls Figure 19
23. check button User setup Drill config Factory setup Dia9 nostics General PF setup Figure 38 Calibration check option Once the calibration check button has been pressed the screen in Figure 39 will be displayed and the Cal Fact can now be seen This value is the kg of seed dispensed for each revolution of the metering unit Max Sp Figure 39 Calibration Factor highlighted This value is generated after every calibration and can now be compared against the calculated Cal Factors in Appendix D at the rear of the manual If large discrepancies are present between the Cal Factors in Appendix D and what is displayed on the control box a recalibration may be required February 2013 Page 29 of 52 CLAYDON Hybrid Hybrid Seed Drill It is important that the machine is set level from front to rear to gain accurate and consistent seed depth between the front and rear seeding tines this is achieved by adjusting the tractors top link To confirm the seed drill is set up evenly the depth wheels positioned across the width of the machine should be firstly set so the drills A Shares scalp the field s surface when in work Figure 40 1 Front A Shares 2 Rear A Shares 3 Seed depth adjustment 4 Depth wheel Ground Level Figure 40 Front and rear tines scalping field s surface This can be achieved by setting the depth wheels to one of the measurements displayed in Figure 41 Th
24. ctor is realistic Adjust metering unit and recalibrate which will increase kg rev factor and therefore increase maximum achievable forward speed Fan s actually operating Hydraulic flow from tractor Sensor amp target functioning and correct PPR value programmed correctly Fan is actually operating Sensor amp target functioning and correct PPR value programmed correctly Hydraulic flow from tractor Seed level is actually low Sensor is functioning correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Fert level is actually low Sensor Is functioning correctly Wiring between sensor and connection box Is correct Wiring between connection box and CAN module is correct Seed level left is actually low Sensor is functioning correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Page 38 of 52 CLAYDON Hybrid 11 23 Ely malag FD CODE L 3 SE CODE L 3 50 3 14 Ely CODE 8314 E 314 Ey CODE Hybrid Seed Drill Seed level right is low Seed only arill with 2 metering units independent left amp right level sensors Both seed levels are low Seed only drill with 2 metering units independent left amp right level sensors Fert level is low only Seed amp Fert drill 2 metering units per product Half Width Enabled Left Side on
25. displayed the Rate screen sub menu the corresponding buttons and their functions can be seen in Figure 20 o0 9 9 peus a wp 2 1 Time 2 Area cut out status N In work X Out of work 3 Seed rate set Target 4 Seed rate applied current 5 Maximum drilling soeed Figure 19 Rate screen Indications February 2013 Page 18 of 52 Hybrid Seed Drill l Navigate to INFO Screen 2 Navigate to RATE Screen currently displayed 3 Navigate to MAIN Screen 4 Number Key Pad 5 Power On Off 6 Decrease Seed Rate by 5 7 Increase Seed Rate by 5 8 Return Seed Rate to target target Seed Rate 100Kg Ha displayed 9 Setup Menu 10 Backspace Key I Enter Key Sew Fa y 9 Figure 20 Rate screen controls Info Screen Figure 21 displayed the Info screen sub menu where the amount of hectares Ha and quantity of seed Kg can be viewed The corresponding buttons and their functions can also be seen in Figure 22 Time Area cut out status V In work X Out of work Area covered Ha Quantity dispensed Kg Time in operation since date Figure 21 Info screen Indications February 2013 Page 19 of 52 Hybrid Seed Drill Select Part Total Normal Total Part Total currently in view 8 Select Grand Total Screen 10 Reset Total only applicable to part total and Normal Total 12 Enter Key _ e oe AH QD
26. e centre of the marker point Figure 7 Marker arms February 2013 Page 12 of 52 CLAYDON Hybrid Hybrid Seed Drill Measure horizontally from the centre of the middle leading tine on the machine to the centre of the marker point the spring tine at the marker arm that runs behind the wheel with the marker arm swung out completely This measurement needs to be equal to the width of the machine e g for a 4 8m wide machine the measurement between the two points must be 4 8m To lengthen the marker arm slacken the U Bolt slide the arm out to the correct length and retighten If the marker arm tine is not aggressive enough during operation then a more prominent mark can be made by adjusting the tine angle This is achieved by slackening the bolts at the stub axle shaft and allowing the whole unit to pivot round on the slotted holes Figure 8 l Stub axel bolts x3 O 2 Marker arm tine 3 Marker arm wheel a Figure 8 Stub axel marker arm arrangement When the drill is in transport the Hydraulic valve taps located on the hydraulic cylinders Figure 9 should be locked off to prevent the marker arms being unfolded l Marker arm cylinder 2 Hydraulic valve tap currently in the closed position 3 Marker arm Figure 9 Location of marker arm isolation valve taps Once your Hybrid Seed Drill is fully connected to the tractor it is recommended that the drills radar should be recalibrated Firstly a 100m str
27. e depth can be accurately set by measuring between the lugs on the depth wheel assembly Figure 41 By altering the depth wheels to one of these measurements the front and rear A Shares should scalp the field s surface evenly if the tractors top link has been set correctly 1 Angled flat on lug on which to measure 2 Hook tape measure over square lug For a 4m 4 8m and a 6m drill measurement should be 495mm For a 3m drill measurement should be 475mm Figure 41 Measurement lugs located on depth wheels February 2013 Page 30 of 52 CLAYDON Hybrid Hybrid Seed Drill Once the machine has been set level front to rear the seeding depth can be set by re adjusting the top links on the depth wheels Figure 42 positioned across the width of the machine Check that the adjusters are all the same length with a tape measure using the position lugs as previously described you can measure between the pins if you prefer 1 Angled flat on lug on which to measure 2 Hook tape measure over square lug a Figure 42 Setting the seeding depth Lower the machine into the ground and drive a short distance brush away the tilth where the straw is still attached and find the original surface level of the field Now brush back and find the depth of the seed compared to the original level of the field Ignore how much soll is directly on top of the seed as this will level out and settle down to the original field level l
28. e displayed the green return key must be pressed once more to accept and store the new factor Once the new factor has been stored the control box will return to the Setup menu February 2013 Page 14 of 52 CLAYDON Hybrid Hybrid Seed Drill Hydraulic Stone Protection Machines only The optional Stone Protection System is designed to safeguard the arill from damage when operating in stony conditions The free flow return on the drill MUST be plugged into the tractor otherwise the pressure released from the stone protection circuit can damage the hydraulic motor The hydraulic fan motors are not covered by warranty Plug the hydraulic pipe running from the valve assembly mounted under the seed hopper into the tractor Turn the tap to the open position parallel to the direction of the pipe Figure 12 this may release the pressure from the circuit back into the tractor depending on the spool valve position Figure 12 Tap in open position Before carrying out work on the hydraulic stone protection system the pressure gauge highlighted in Figure 13 MUST read 0 with the spool valve in float or open position It is dangerous to work on the hydraulic circuit while it is under pressure Figure 13 Stone Protection pressure gauge February 2013 Page 15 of 52 CLAYDON Hybrid Hybrid Seed Drill Using the tractor s hydraulics the circuit needs to be pressurised to the required pressure maximum pressure is set
29. e so that it can t be caught or snagged All of the hydraulic hoses on your Hybrid Seed Drill have been colour coded and are displayed in Figure 2 THE HYDRAULIC FREE FLOW SERVICE MUST BE PLUGGED IN PRIOR TO THE DRILL BEING OPERATED Connections Color l Light cable 2 Folding wings Yellow i 3 Stone Protection White 4 Marker Arms Green 5 Hydraulic Fan Free flow Red service 18L connector 6 Hydraulic fan Pressure 2x Red markers i a DON n O0 90 Only present on 4m 4 8m and m Optional extra Figure 2 Tractor connections model shown 4m 4 8m February 2013 Page 9 of 52 joo Hybrid Seed Drill The following labels Figure 3 can be found located on the front of the drills seed hopper these labels specify the corresoonding hydraulic connections and there color coded indicators The amount of hydraulic services on your Hybrid drill will alter depending on the specifications and the drills width Hrdyaulic Services Folding Yellow 4 4 8 and 6m drills only Optional extra Marker Arms Green Stone Release White Hrdraulic fan Red Figure 3 Labels for hydraulic services Mount the RDS Artemis Control Unit in a position in the cab easily visible and reachable from the driving position Mount the drill onto the three point linkage Run the electric cables into the tractor cab and connect them to the relevant sockets within the cab they will only fit their correct part
30. ed high Error between actual motor speed and target motor speed is greater than 10 Seed motor soeed low 2 Error between actual motor speed and target motor speed is greater than 1076 Both motors are disabled due to pressing the on screen motor inhibit buttons Re press to re enable the motors or ignore to continue with the motors inhibited Based upon the calibration factor this is the maximum speed that can be achieved If this is too low then open the metering unit slide further and re calibrate Seed level upper is actually low Sensor is functioning correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Is drill still lifted Sensor amp target switch functioning and correct Spring toggle switch correctly set operating Operating logic not set correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Target motor speed too low Erratic forward speed signal Erratic loading on motor via metering unit Check radar Reduce Metering Unit Opening Slide Re calibrate Target motor speed to high Erratic forward speed signal Erratic loading on motor via metering unit Check radar Increase Metering Unit Opening Slide Re calibrate Page 40 of 52 CLAYDON Hybrid CODE 43 16 Ely I C E 4 IL LEFT 8317 lv CODE H SLF Hybrid Seed Drill Seed metering
31. ed while loading the hopper and cleaning the machine after use with compressed alr e The hydraulic system on the machine operates under high pressure and pressurised hydraulic oil is dangerous Connecting disconnecting the drill must only be undertaken with the tractor engine turned off and the pressure in the hoses released e Before operating the machine ensure no one is standing within range of its turning circle including the marker arms February 2013 Page 7 of 52 CLAYDON Hybrid Hybrid Seed Drill IMPORTANT INFORMATION for Drills with Hydraulic Stone Protection System e BEFORE pressurising the stone protection circuit ensure that the drills hydraulic free flow service is plugged in as the overflow pressure is directed into this circuit and dissipated back into the tractor through the free flow return this will avoid damage to the stone protection circuit or fan motor which are not covered by warranty e Always release the pressure from the stone protection system before working on the hydraulic system e Release the pressure from the stone protection system for over winter storage and allow the rams to go to closed centres therefore allowing the rods some protection against corrosion e The Tungsten points on the leading tines should be protected by parking the drill on wooden boards The terms front rear left and right in this manual refer to the machine as follows l 2 3 4
32. eeeeeeeseeeeeeeeas 17 Navigating the Control Unit brief guide 17 WANA SOUS CUE BEREIT TT TP 17 St IUE T cee 18 MO SONS Ci RTI 19 OG CID MEMU mE 20 T AMININO mTT Rare 21 PARA S 1 SUM saosin netrccdsecnc 22 Setting Up the Seeding System cccccccssesccceceeeeeeeeeceeeeeeeeeeseeeeeeeeseeaueeeeseseaaeceeessaaaeeeeessaageeeessaaaaes 23 Calibrating the Seed Hale rint er rte ntaiesteedaveddeodasansaeanbedseniatdetendanendeodanantnoustasdendtdass 24 Overview of the Metering UNit cc cccccccececc ees eeeeeeeceee eee nennen nemen nne nene ne nemen neas nennen 24 Mig 25 CAMA UOS NOC TR eee ere ee eee 29 PIC SE Se 2B d MEINER 30 SELM CNE dE i o 30 Set the Seeding Doplata iia ai aeiia a a iieii 30 Set Up the Level Board nein eie nnper i ia a eiaa eiiie ask it 32 CE e MI a INS NUN m x O E O 34 Bille CCU F O S ae OO OUT 34 Changing Wearing P alis csscsucueniptn tuis sit indu iqisoriRSeque aaia eaei d isa a ai 36 Changing agendam T 36 DU Aui ccU c TT O 37 i erziofo ale REST aci TRE IO 37 Changing Seed Boots uci ettonte attente tatu ba kk bos auda etat esu eode tuu ERE cx DREPUA D habea taxe Mae Rb MAE 37 Appendix A Artemis Fault Codes cccccccccsseeccceceeeeeeeeesea
33. eeseeeeeeaeeeceeesaeaaeeeeesaeaeeeeeesseaeeeeeeseaaeeeeeesaaess 38 Appendix B Declaration of CORTOFIilly en ciui itnn otc i een ERE enne aen po capu e heec eee ples tux kh dus 45 Appendix C Metering Unit Slider Positions eeslssseesseseseeseeeeeeene nnnm 46 Appendix D Calibration Factors ssseeesssesissseseeeeen nnne nennen nnne nnns nnn rn nnn nnns 50 s EZ L B SC GS PRENNE ees eewecnereoseeusqoscacsaren eoace 52 February 2013 Page 2 of 52 CLAYDON Hybrid Hybrid Seed Drill In order to activate your Claydon Warranty this page must be completed and returned to Claydon Yield O Meter Ltd Gaines Hall Wickhambrook Newmarket Suffolk CB8 8YA Tel 44 0 1440 820 327 Fax 44 0 1440 820 642 IF THE REGISTRATION DOCUMENT IS NOT RETURNED THEN THE DRILLS WARRANTY WILL BE VOID Hybrid Drill Warranty Registration ADDRESS NUMBER PLEASE ENSURE The Machine is washed off upon delivery to remove any road salt The drills hydraulic free flow service is plugged in prior to the drill being operated February 2013 Page 3 of 52 CLAYDON Hybrid Hybrid Seed Drill Safety stickers can be found located on your Claydon Hybrid drill at numerous locations these stickers must be observed to ensure your safety and that the machine is operated in a safe manner If any of the stickers become illegible or peel off new stickers can be ordered and attached in the appropri
34. er be increased or decreased by altering the adjuster at the rear of the drill Figure 46 The levelling boards are designed to level the ridges created from the leading tine and not to perform any kind of pressing operation The Boards should not be set at too steep an angle and should have the appearance of skiing along the surface The green harrow tines may also be fitted to follow behind the levelling boards Figure 46 or used as an alternative depending on the machine specification R 1 Green harrow tines mne 47 EC 2 Level board A PP FJ 3 Level board tine adjustment Figure 46 Level board February 2013 Page 32 of 52 CLAYDON Hybrid Hybrid Seed Drill The level board angle is adjusted on the pin holes where the tool bar connects to the arms Figure 47 The green harrow tines should be situated at an acute angle with the tail of the tine positioned firmly and parallel to the ground This angle can be adjusted by altering the pin holes on the connecting arm Figure 47 Figure 47 displays our suggested setting Remove pin fo alter angle of ski boards Rear tool bar Remove pin to adjust height of green tines Connecting arm for double tool bar Remove pin fo alter angle of green tines E aD oe e Figure 47 Ski boards and green tines adjustment settings The level board height is altered on the adjuster located on the swivel beams Figure 48 The levelling boards can be lifted complete
35. erview February 2013 Page 35 of 52 Hybrid Seed Drill 8 Marker arm 3m Hybrid 9 Wings bearings 6m Hybrid Figure 52 Details of lubrication points Changing Wearing Parts 7 Folding pivot pin Changing Front Tines To change the front tine simply remove the lynch clip and remove the 19mm pin slide the entire tine out and replace the entire tine with a new one Refit pin and lynch pin IF WORK IS REQUIRED TO BE CARRIED OUT WHILST THE DRILL IS RAISED ENSURE A SUBSTANTIAL PROP IS POSITIONED SAFELY UNDER THE DRILL PREVENTING IT FALLING UNDER ITS OWN WEICHT Removal MEME Replacement Figure 53 Changing front tines February 2013 Page 36 of 52 CLAYDON Hybrid Hybrid Seed Drill a ee ee When new the steel of the tine protrudes beyond the Tungsten this is to protect the Tungsten when transporting new drills After use the drill should be placed on wooden boards to protect the Tungsten Great care needs to be taken when lowering the drills onto concrete It is recommended that the wheels on the Hybrid seed drill should be inflated to a pressure of 30 psi 2 bar On the seeding leg hook the removal tool supplied over the top of the share and push the pin down hit the top with a hammer to remove the share Now simply slide the new share up the speed Loc adaptor and hit the bottom with a hammer until the locking pin pushes back out IF WORK IS REQUIRED TO BE CARRIED OUT WHILST THE DRILL IS RAISE
36. etch should be measured out and marked using two indicators The drill should be in the ground and the tractor should be stationary at the beginning of the 100m run It is recommended that the marker arm should be extended out so If can be used as a guide when crossing the second indicator February 2013 Page 13 of 52 CLAYDON Hybrid Hybrid Seed Drill Figure 10 displays how to navigate the Artemis control box in order to select the radar recalibration process once the tractor and drill are in position Setup Menu Select User setup A 2 Drill confisi 3 Factory setup 4 Diagnostics 5 General PF set o Select Speed sensor factor 1 DisPlay i b 2 perce sensor factor JA mise Select Auto Cal Figure 10 Navigation process to radar recalibration By selecting the Auto Cal option the radar calibration procedure can now begin this procedure should start from a standstill and come to a stop at the 100m indicator The screens displayed on the Artemis box during this procedure can be seen in Figure 11 Press the green return key to begin the process and start driving Now drive the 100 metres Om 25m Sm 75m 166m e Stop on 100m mark Press when comPlete Pulses 12255 When the marker arm makes contact with the second indicator stop the tractor and press the green return key Figure 11 Radar recalibration sub menu On completion of the 100m run a new factor will b
37. h Dutch Veldbone Veldbonen Veldbone Spanish Trigo Trigo Trigo Trigo Spanish Spanish Cebada Cebada Cebada Cebada Spanish Spanish Frijoles Frijoles Frijoles Frijoles Swedish Vete Vete Vete Vete Swedish Swedish Korn Korn Korn Korn Swedish Swedish B nor B nor B nor B nor Danish Hvede Hvede Hvede Hvede Danish Danish Byg Byg Byg Byg Danish Danish B nner B nner B nner B nner German Weizen Weizen Weizen Weizen German German Gerste Gerste Gerste Gerste German German Bohnen Bohnen Bohnen Bohnen French Bl Bl Bl Bl French i i i i French French French Haricots Haricots Haricots Haricots Polish Pszenica Pszenica Pszenica Pszenica Polish Z Z Z Polish i ien ien ien Polish Polish Fasola Fasola Fasola Fasola P enice P enice P enice P enice Zi Zi Zi Zi Czech Oves Oves Oves Oves Fazole Fazole Fazole Fazole ooss 69 52 43 ss ooss 68 s a 34 0078 93 7 s 47 005 90 68 se 45 oos 17 s z 59 oos 112 a 70 56 oss m 1 88 71 012 134 10 84 67 0131 157 118 98 78 189 142 118 0149 179 134 112 90 0205 246 184 154 123 0 261 0280 336 252 210 168 0 334 401 301 251 200 0353 424 318 265 212 0372 446 335 279 223 February 2013 Page 50 of 52 English Peas Peas Italian Piselli Piselli Dutch Erwten Erwten Spanish
38. ical right using the navigation keys Figure 25 Spray width is altered by adjusting target bout no Target bout no Increase decrease Select rhythm bout target no Figure 25 Tramline sub menu screen February 2013 Page 21 of 52 CLAYDON Hybrid Hybrid Seed Drill In order to view the fan speed alarm limits and the status of the hopper level sensors the alarms setup menu can be accessed by pressing the alarms shortcut key Figure 26 aa User setup 2 Brill config Factory setup Disasnostics General PF setut setup Menu Alarms Setup Button Figure 26 Alarms shortcut key Figure 27 displays the recommended fan speed threshold settings and whether the seed low level sensor is activated If the fan speed drops or exceeds the pre set alarm thresholds then the system will alarm and the metering units will not run l Lowerlevel fan speed setting 2 Upperlevel fan speed setting 3 Seed low level sensor Currently On 4 Navigation buttons Figure 27 Alarms sub menu screen The seed low level alarm can be turned off by firstly using the navigation buttons located on the left of the Artemis unit to select the level sensor option Once selected use the navigation buttons on the right of the Artemis unit to turn the level sensor either on or off February 2013 Page 22 of 52 CLAYDON Hybrid Hybrid Seed Drill As previously described make sure the Arfemis Control Unit
39. ioned when sowing seed with a 6m Hybrid seed drill Firstly select the desired product and then select the closest required application rate Kg Ha the metering unit should then be opened to the slider setting displayed e g If wheat was required to be sown at 236 Kg Ha the slider on the metering unit would be set at 95 on a 6m drill highlighted below Table 4 Metering unit slider positions for a 6m Hybrid Drill English Italian Dutch Spanish Swedish Danish German French Wheat Gr no Tarwe Trigo Vete Hvede Weizen Rye Segale Rogge Centeno R g Rug Roggen Barley Orzo Gerst Cebada Korn Byg Gerste Oats Avena Haver Avena Havre Havre Hafer Avoine Beans Fagioli Veldbonen Frijoles B nor Bonner Bohnen Haricots Fertiliser Fertilizzante Meststof Fertilizante G dningsmedel G dning D nger Peas Lupins Piselli Erwten Chicharos Artor Arter Erbsen Lupini Lupinen Lupino Lupine Lupiner Lupinen Vetches Vecce Wikke Vezas Vicker Vikker Wicken Maize Mais Mais Maiz Majs Majs Mais Grass Oilseed Rape Erba C lza Gras Koolzaad Hierba Colza Grasfro Raps Graesfro Raps Grassamen Raps Red Clover Grass Trifoglio Rosso Erba Rode Klaver Gras Tr bol Rojo R dkl ver R dkl ver Rotklee Hierba Gr sfr Gr sfr Grassamen Turnip R pa Knolraap Nabo K lrot Majroe R be Bl Seigle Orge Pszenica Zyto PSenice Zito Engrais Poi
40. ly Seed drill 2 metering units per product Half Width Enabled Right Side only Seed drill 2 metering units per product Single Motor Metering OTT Seed level right is actually low Sensor is functioning correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Seed levels are actually low Sensors are functioning correctly Wiring between sensors and connection box is correct Wiring between connection box and CAN module is correct Fert level is actually low Sensor is functioning correctly Wiring between sensor and connection box is correct Wiring between connection box and CAN module is correct Left side motor is disabled due to pressing the on screen motor inhibit button Re press to re enable the motor or ignore to continue with half width drilling Right side motor is disabled due to pressing the on screen motor inhibit button Re press to re enable the motor or ignore to continue with half width drilling Motor is disabled due to pressing the on screen motor inhibit button Re press to re enable the motor or ignore to continue with the motor inhibited February 2013 Page 39 of 52 February 2013 Hybrid Seed Drill Dual Motor Metering OTT Max Forward Speed Seed Level Upper is Low Pre Level Area cut out Flashes up for 1 second every 3 seconds when system is out of work Seed motor spe
41. ly out of work with this adjuster or have some downward pressure applied to them Depending on the field conditions the following Ski board settings are recommended and should be achieved using the adjuster Wet conditions Remove pressure from ski boards Dry conditions Apply pressure to ski boards Ideal conditions Zero pressure top link becomes loose during adjustment 1 Level board adjuster Figure 48 Setting level board February 2013 Page 33 of 52 CLAYDON Hybrid Hybrid Seed Drill Care and Maintenance Lubricating Points Lubrication should be performed by using multi purpose grease An overview of the greasing points for the 4m to 6m Hybrid drill is given in Figure 49 and Figure 50 an overview for the 3m hybrid is given in Figure 51 with identification numbers corresponding to the detail of lubricating points in Figure 52 Not all lubrications points apply to all machines and some are multiple lubrication points so some identification numbers may not appear or may be repeated N B At regular intervals lubrication should also be placed on the drills top link pin to prevent excessive wear from the upper link ball GG 0 Figure 49 Lubrication points 4 to 6m Hybrid February 2013 Page 34 of 52 Hybrid Seed Drill PM 0 ga Figure 50 Lubrication points 4 to 6m Hybrid pi s gt Fa E Figure 51 Lubrication points 3m Hybrid drill ov
42. m inside the hopper pull the end of the bracket nearest the sensor away from the hopper and over the locating bolt head Move the sensor to the required position and locate on the appropriate bolt head Figure 29 Level sensor in lower position February 2013 Page 23 of 52 CLAYDON Hybrid Hybrid Seed Drill Prior to explaining the calibration process an overview of the metering units highlighting the various components can be seen in Figures 30 34 Lid to empty hopper Air pipe Slider position scale Red lever Handle Calibration button Red cog should always remain in the closed position high gear Lid for emptying large seed amounts and cleaning seed wheel Outlet for emptying smaller seed amounts e g OSR iggigigd jb 3 Figure 31 Gearing February 2013 Page 24 of 52 CLAYDON Hybrid Hybrid Seed Drill l U Bracket 2 90 degree Bend man Figure 32 Rear view l Speed sensor for metering system 2 Calibration button l Slider position Figure 34 Slider position Method February 2013 Page 25 of 52 CLAYDON Hybrid Hybrid Seed Drill To make sure seed is being metered and sown at the required rate it is necessary to take and weigh a sample from the metering unit This weight is then entered at the Artemis Control Unit which will calculate and adjust for any error i e the error being the difference in seed weight between what the control unit calcul
43. n and hold for another three seconds to stop seed flow Empty the bucket 7 To commence the automatic calibration procedure position a bucket which you have accurately weighed in its place under the metering unit Press the white button and hold for three seconds to start the metering motor When you have obtained a good sized sample press the white button again and hold for another three seconds to stop seed flow the motor may not stop immediately 14 Type in the seeding rate you require on the number pad 15 The Control Unit will automatically set the seeding rate and display the maximum drilling speed If you consider this speed too slow you can wind the handle on the metering unit out further to allow more seed through and repeat the calibration process 16 To check that the calibration is now correct repeat the process The error displayed should now be between 0 and 476 17 MAKE SURE you replace the 90 bend on the bottom of the metering unit 18 Ensure the fan speed is set between 3200 Ensure the fan speed is set between 4300 3500 RPM 4500 RPM February 2013 Page 26 of 52 Hybrid Seed Drill TRI Figure 35 1 Red lever on shaft out small Figure 35 2 Red lever on shaft in large seed setting seed setting Figure 35 Red lever positions Figure 36 1 Deflector set for small seeds Figure 36 2 Deflector set for large seeds OSR cereals Figure 36 Deflector settings Febru
44. ners see Figure 44 To avoid exposure to moisture keep the connections inside the cab wherever possible Cables shown connected l o y Artemis control unit 2 4 Data cable from RDS box Electric power cable to RDS box Electrical power cables to battery terminals Ai 4 gt 3 Figure 4 Electric cable connections February 2013 Page 10 of 52 CLAYDON Hybrid Hybrid Seed Drill CAUTION MAKE SURE THE FAN RETURN IS PLUGGED INTO A FREE FLOW RETURN ON THE TRACTOR Connect the hydraulic hoses to the tractor spools in their relevant pairs The 1 ISO female coupling with 18L male thread supplied with your drill will have to be connected to the tractor rear axle If necessary your tractor dealer will advise The return pipe cannot just be inserted into the filler cap as the oil cannot return to the pump sufficiently quickly in many tractors DO NOT CHANGE THE 1 ISO TO A DIFFERENT SIZE AS THIS COULD CAUSE DAMAGE TO THE MOTOR WHICH ARE NOT COVERED BY WARRANTY The fan return cannot be connected to the tractor ISO Once the drill is attached and at the correct working depth the top link should be set at an angle in which the convergence point between the upper and lower link arms should fall at the front axle Figure 5 This can be achieved by altering the top link pin attachment points on the tractor and arill This ensures stability and the mass of the implement i
45. s Lupino Vezas Ma z Hierba Colza Tr bol Rojo Hierba Nabo Swedish Vete R g Korn Havre B nor G dningsmedel Artor Lupine Vicker Majs Grasfr Raps R dkl ver Gr sfr K lrot Danish Hvede Rug Byg Havre B nner G dning rter Lupiner Vikker Majs Gr sfr Raps R dkl ver Gr sfr Majroe German Weizen Roggen Gerste Hafer Bohnen D nger Erbsen Lupinen Wicken Mais Grassamen Raps Rotklee Grassamen R be French Bl Seigle Orge Avoine Haricots Engrais Poi Lupine Vesce Mais Gazon Colza Trefle Rouge Gazon Navet Polish Pszenica Zyto Jeczmien Owies Fasola Zapylaczka Groszek tubin Wyki Kukurydza Trawy Rzepak Koniczyna Czerwona Trawy Rzepa Czech P enice Zito Je men Oves Fazole hnojivo Hr ek Lupina Vikve Kuku ice Travn epka erven Jetel Travn Tuf n 0 77 0 74 0 68 0 5 0 85 1 0 81 0 76 0 83 0 79 0 36 a a a 4 j 4 Jj 19 28 36 53 February 2013 Page 47 of 52 CLAYDON Hybrid Hybrid Seed Drill Table 3 displayed where the slider on the metering unit should be positioned when sowing seed with a 4 8m Hybrid seed drill Firstly select the desired product and then select the closest required application rate Kg Ha the metering unit should then be opened to the slider setting displayed e g If wheat was required to be sown at 263 Kg Ha the slider on the metering unit would be set at 85 on a 4 8m drill highlighted below Table 3 Metering unit slider positions for a 4 8m Hybrid Drill English Wheat Rye Barley Oats Be
46. s used correctly Upper link point Upper hitch point Lower link point Lower hitch point Vertical virtual hitch point d addo xa Figure 5 Top link convergence position February 2013 Page 11 of 52 CLAYDON Hybrid Hybrid Seed Drill Raise the machine off the ground and fold the wings fully upright applies to 4m 4 6m and m machines Once folded turn the hydraulic tap parallel to the cylinder to lock the wings in the upright position Figure 6 To unfold the wings turn the hydraulic tap in the opposite direction and operate the spool valve Never transport along public highways without isolating the folding wings isolate folding wings Figure 6 Location of wing isolation hydraulic tap On delivery of the drill the marker arms may be in their shortest position for transport Both marker arms will have to be set up for the working width of the machine Additionally should the driving position not be central either through driver s choice or position of the seat it may be necessary to adjust the two markers to avoid gaps or overdrilling Figure 7 shows where to measure from in order to set the marker arm distance followed by a brief explanation on how to achieve this It is advised to carry out this process when the drill is in the ground and at the correct working depth e Marker arm extended 2 Marker arm folded in 3 Working width of the machine from the centre of the middle tine to th
47. should be checked and retightened after a few operating hours Nuts may come loose due to machine vibration February 2013 Page 5 of 52 CLAYDON Hybrid Hybrid Seed Drill Thank you for your purchase of a new Claydon Hybrid Seed Drill The Claydon Hybrid Seed Drill is a high performance drill designed to sow seed of a wide variety type and size Due to its electronically controlled metering system this is achieved accurately and economically The purpose of this Operators Manual is to comprehensively explain to the operator how to set up use and maintain the machine It isimportant that the operator reads this manual carefully to correctly set up use and maintain the machine safely In particular it is essential that the Warnings and Cautions section has been read carefully For any further assistance or explanation please contact Claydon Yield O Meter using the contact details given on the front cover The serial number stamped on the left hand plate near where the top link attaches will also need to be quoted The Claydon Hybrid Seed Drill will give many years of excellent service with little maintenance due to Its robust construction and its small number of moving parts However for optimum machine life some maintenance will be necessary We reserve the right to make future modifications to the machine that could make some diagrams and descriptions in this manual out of date While the clarity of the manual should not be affec
48. ted by this please bring any concerns to the attention of Claydon Yield O Meter Ltd for us to resolve the problem The Claydon Range offers drills with the following specification With level boards removed February 2013 Page 6 of 52 CLAYDON Hybrid Hybrid Seed Drill In addition to the machine identification plate the serial number of the machine is stamped into the left hand main mounting beam Location of serial number Detail of serial number enhanced Record your serial number here oo cece cece eee nce cess ee e he he ese eme esses eene You may need to quote the serial number of your machine when you order spare parts in the future The Claydon Hybrid Seed Drill conforms to Machinery Directive 2006 42 EC see Appendix B Declaration of Conformity at the rear of the manual The A weighted emission sound pressure level of measurements taken directly at the fan is 9AdBA These warnings and cautions must be observed when operating the Hybrid Seed Drill e Ensure total weight of tractor drill combination does not exceed permitted limits and weight of tractor is sufficient for safe field and road use e Do not allow anyone to stand between tractor and drill during coupling uncoupling procedures e For maintenance agdjustment of the drill ensure that it is lowered to the ground on the 3 point linkage e Seed dressing is highly poisonous so protective measures gloves goggles facemask must be us
49. wiring of forward speed in alarmed connection box Check for continuity between pin 2A on MCM 1 white wire and pin 2A on MCM 2 Check for blockages in the metering unit Disconnect motor from metering unit and ensure both units rotate separately Check motor and gearbox Open and Close Finger Switch Area Cut Out to Reset Alarm Criteria February 2013 Page 44 of 52 CLAYDON Hybrid Hybrid Seed Drill EC Declaration of Conformity In accordance with EN ISO 17050 1 2004 We Claydon Yieldometer Ltd of Gaines Hall in accordance with the following Directive s 2006 42 EC The Machinery Directive hereby declare that Equipment Claydon Drills Model number Hybrid Serial Number is in conformity with the applicable requirements of the following documents Ref No Title Edition date EN ISO 12100 1 2003 Safety of Machinery Basic Concepts 2003 EN ISO 12100 2 2003 Safety of Machinery Basic Concepts 2003 I hereby declare that the equipment named above has been designed to comply with the relevant sections of the above referenced specifications and is in accordance with the requirements of the Directive s Nt gd 9 E n oR e C Name Oliver Claydon Position Director of Design and Production Done at Gaines Hall Wickhambrook On 21 06 2012 The technical documentation for the machinery is available from Name Claydon Yieldometer Ltd
Download Pdf Manuals
Related Search