Home

Yunzi - User Manual v2.1

1. 3 blinking green Yes Press again the HIDE button to obtain a picture 4 blinking red Yes Unit is in cooldown mode switching off Lamp time has reached 2900 hours prepare to replace the lamp soon If used in low power mode replace the lamp before 4000 hours 5 6 orange AUTION When in Cool Down mode do not pull out the plug from the outlet Also do not block the air inlets exhaust vents by standing the projector on its end or laying it on its side When the projector is running for more than 1 minute the Standby ON LED will automatically switch OFF O R699820 Yunzi Series User Manual ET 5 0 CONNECTIONS 4 4 Operating and Navigation Buttons Power button Input source OK Up down Left right Menu Back Button Description Power button To turn On or Off the projector Input source To switch input source OK Enter To select or to confirm action Up down left right To navigate into On Screen Display OSD Menu Menu To display On Screen Display OSD Menu Back To return to previous menu or cancel action 5 0 CONNECTIONS 5 1 Caution when connecting a device to HDMI input rior to connecting any device to this unit switch the projector in standby mode Never connect a A to this unit when the projector is in operate mode The HDMI termination is a self powered connection and c
2. Examples You want to Command to send send 3Fh 89h 01h 50h 57h OAh Check if the projector is switched ON receive 06h 89h 01h 50h 57h 0Ah confirm cmd receive 40h 89h 01h 50h 57h 31h OAh projector is ON 15 2 LAN protocol LAN RJ 45 communication specification To set the projector to LAN Control Mode go to the Function menu then set the Communication Terminal from RS 232C default to LAN The network settings may have to be modified in the projector s network menu to match your current LAN network DHCP Client When set to ON the projector s IP address will be automatically set by the DHCP server on the LAN IP Address Sets the IP Internet Protocol address of the projector A valid address must be set for this unit Subnet Mask Sets the Subnet Mask Default Gateway Sets the Default IP Gateway of the projector MAC Address A 6 byte hex number that uniquely identifies the projector on the LAN The value is unique to each individual unit on the LAN network The first step to verify that the network configuration of this unit has been correctly set is to ping the projector from a computer on the network using the command prompt Sending a LAN Control Command In order to send a Remote Control compatible command to this unit you must open a TCP connection on port 20554 and send a command immediately as the connection will be dropped within 5 sec of inactivity If for any reason you have to c
3. E Connect the lens motorization to the 12V Trigger output Configure into Function Menu Trigger On Anamo The Function Trigger menu determines the 12V Trigger output located in the panel input at the rear of this unit This is a global parameter for all inputs Set the 12V Trigger to On Anamo mode so that it is most of the time Off and switches On when the picture is in Cinemascope format and Anamorphic mode A is selected The picture is then vertically stretched and the lens is needed Set 12V Trigger to Function Trigger gt On Anamo Video source is 16 9 set Anamo rphic to Off When you select a 16 9 input choose the anamorphic OFF to obtain move the anamorphic lens out Menu Installation gt Anamorphic gt Off 36 R699820 Yunzi Series User Manual 14 0 MAINTENANCE Video source is Cinemascope set Anamo rphic to Mode A Select Anamorphic mode for this input in the menu Input Installation Anamorphic Mode Anamo rphic modes Anamo Mode A Anamo Mode B When you press sequentially the Anamo rphic button you change the mode from OFF Mode A and Mode B Mode A is intended to be used with an anamorphic lens to watch 2 35 1 content on a 2 35 1 screen Mode B is intended to be used to quickly switch to 16 9 content without moving the anamorphic lens The Anamorphic Lens is automatically placed in front of the projector to restore the correct picture aspect ratio Appear
4. 251 cm 507 cm 80 2 2037 mm 45 1 1146 mm 279 cm 562 cm 100 2540 mm 110 2794 mm 87 2 2214 mm 49 0 1245 mm 301 cm 613 cm 95 9 2435 mm 53 9 1370 mm 331 cm 675 cm 138 3505 mm 150 3810 mm 120 3 3055 mm 67 7 1718 mm 418 cm 843 cm 130 7 3321 mm 73 5 1868 mm 453 cm 860 cm 180 4572 mm 200 5080 mm 156 9 3985 mm 88 2 2241 mm 545 cm 1107 cm 174 3 4428 mm 98 1 2491 mm 606 cm 1230 cm The projection screen sizes and projecting distances in the table above are provided only as a guide Please use them as reference during installation The distances are calculated for a projection image of 16 9 aspect ratio 2 10 Setting the Lens and using Lens Memories Adjust the picture position The optimum image can be obtained when the centre of this projectors lens and the screen are placed perpendicular to each other Take note of the projection angle when placing them You can also use up to 15 up and down position and configure trapezoidal correction Horizontal Shift 34 Screen Height H This unit comes with a vertical and horizontal shift to suit most installations Make sure that your installation Vertical Shift 80 does not exceed 80 vertical offset and 34 horizontal offset to avoid trapezoidal correction 12 R699820 Yunzi Series User Manual 2
5. NB To further avoid Infrared interferences or line of sight issues you may also order the Radio Frequency Synchronization Kit with RF synchronized 3D Glasses The RF kit cannot synchronize Infrared 3D Glasses 2 5 Best seat position for 3D projection A 3D projection that makes use of stereoscopic images is very similar to an illusionist show where the brain is tricked to perceive two pictures as a real 3D scene The trick is easily revealed If you move from one side to the other side of the screen there will be a place where you will be off axis enough to let you perceive the flatness of the projected pictures instead of interpreting them as a 3D object If the parallax is not appropriate to the screen size the two pictures will be perceived distinctly and therefore the brain will interpret the 3D projection as two superposed pictures In general the perception of the 3D effect will vary according to your seat position and to the screen size When a movie is produced for 3D projection the director knows the exact distance where the 3D effect will be perceived In R699820 Yunzi Series User Manual 9 2 0 INSTALLATION GUIDELINES general the recommended distance is three times the height of the screen to obtain the best 3D effects H Screen Height Seat distance formula 3 x H 16 9 movies 3 x H 1 69 x B 2 37 1 movies 3 x H 1 26 x B Best seat position for 3D projection 2 6 Environment of Use D
6. Paste paste values stored in memory to current profile Reset reset to the default 2 2 gamma coefficient Gamma Adjustment can be copied from all modes Paste can only be used for Custom modes Additional Gamma settings for Yunzi 2 amp 3 Film1 Eastman gamma R699820 Yunzi Series User Manual 7 0 PICTURE ADJUST SETTINGS Film2 Fujifilm gamma Film3 more tone than Film1 Film4 more contrast than Film2 7 4 Dark Bright Level This setting modifies the gamma curve locally in the dark and bright areas Dark Level adjust gamma curve between OIRE and 15IRE each color can be adjusted from 7 to 7 Bright Level adjust gamma curve between 85IRE and 100IRE each color can be adjusted from 7 to 7 7 5 Picture Tone It allows a fine adjustment steps of the global picture brightness while maintaining the correct contrast level to keep good black and bright levels Available when Film Picture profile is selected White sets the overall exposure from 16 under exposed darker up to 16 over exposed brighter Red Green Blue to set individually each color channel exposure 7 6 Contrast The contrast function is used to adjust the contrast between the light and dark areas of the displayed image A correct contrast setting is important for good image reproduction Adjust the Contrast value between 50 and 50 7 7 Brightness The brightness function is used to adjust the overall light output Adjust the Brightness
7. However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encourage to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The Federal Communications Commission FCC is an independent United States government agency created directed and empowered by Congressional statute The FCC was established by the Communications Act of 1934 as the successor to the Federal Radio Commission and is charged with regulating all non Federal Government use of the radio spectrum including radio and television broadcasting and all interstate telecommunications like wire satellite and cable as well as all international communications that originate or terminate in the United States The FCC s jurisdiction covers the 50 states the District of Columbia and U S possessions 2 0 INSTALLATION GUIDELINES 2 0 INSTALLATION GUIDELINES 2 1 About 3D Content and 3D Projection This unit is compatible with 3D playback The source can be connected using one of the two availab
8. projector by a programmable RCU using NEC 5 protocole Data Data lenght may vary EoD Fixed to OAh Available Operating commands Header 21h Connection RS 232 Command 00h 00h Description Check the serial connection Power ON 50h 57h If the projector is in stand by mode this command switch the unit ON Power OFF 50h 57h If the projector is powered ON this command switches this unit into Stand by Mode Switch Input 49h 50h Switch active input to Component Switch active input to VGA Switch active input to HDMI 1 Switch active input to HDMI 2 Switch to next input Switch to previous input 2Dh Gamma 47h 54h 30h 31h Set Gamma to Normal Set Gamma to A R699820 Yunzi Series User Manual 41 15 0 MISCELLANEOUS 42 Gamma 47h 54h 32h Set Gamma to B 33h Set Gamma to C 37h Set Gamma to D 38h Set Gamma to E 39h Set Gamma to F 45h Set Gamma to G 46h Set Gamma to H 34h Set Gamma to Custom1 35h Set Gamma to Custom2 36h Set Gamma to Custom3 4th Set Gamma to Film1 42h Set Gamma to Film2 43h Set Gamma to Film3 44h Set Gamma to Film4 Gamma Value 47h 50h 30h Set value to 1 8 Gamma set to W Custom1 3 38h Set value to 2 6 RCU code 53h 55h 52h 43h 30h Set Unit to receive commands from RCU code A 31h Set Unit to receive commands from RCU code B RCU Commands and sending them through RS 232 Header 21h Power ON Power OFF
9. 0 INSTALLATION GUIDELINES This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen position Adjust the picture to your screen The Vertical Shift level is between 80 and 80 of the Screen Height 0 80 x H The Horizontal Shift level is between 34 and 34 of the Screen Base 0 34 x fthe projector is not installed perpendicularly to the screen use keystone correction to fulfill your screen Note that using keystone correction may be disabled by 3D projection If you want the best possible 3D pictures It is not recommended to use trapezoidal correction f you plan to use the vertical and horizontal shifts without keystone correction make sure to not exceed the values contained in the tab below Left Right shift 0 5 10 15 20 25 30 34 max Up Down shift 80 74 66 57 47 34 18 0 2 10 0 1 Adjust the picture position The Yunzi Series projector has motorized vertical and horizontal shifts Browse into the Menu to the Lens Control setting into the Installation menu select the shift adjustment Or use the direct access button on the Remote Control Unit Lens Control to make the lens adjustment You can use self generated test pattern of the projector or an external pattern from a calibration DVD by example by setting the Adjust pattern option to Off 2 10 0 2 Adjust the picture Zoom Into
10. 12Vcc 100mA Select the trigger output behavior Off 12V trigger voltage state is always low On Power 12V trigger state is high when the projector is powered ON To be used with motorized screens On Anamo 12V trigger is high only when Anamorphic Mode A or Mode B is engaged To be used with motorized anamorphic kits 11 2 Off Timer You can configure this automatic power Off function that will switch off the projector when there is no operation or after a determined timer Choose the duration of the timer between Off 1 hour 2 hours 3 hours and 4 hours 11 3 High Altitude Mode Select this when the projector is in a location of low atmospheric pressure On or Off 34 R699820 Yunzi Series User Manual 12 0 INFORMATION MENU 11 4 ECO Mode This setting when set to On will minimizes the power consumption in the Standby Mode Additionally this product will automatically switch Off whenever the input signal is interrupted for 30min NB When Eco Mode is On this unit may no longer be switched On from Standby Mode by using RS 232C or LAN communication 11 5 Communication Terminal Sets the input to which the control device is connected to It is not possible to use both RS 232C and LAN inputs at the same time Settings RS 232C LAN 11 6 Network When the Communication Terminal selected is LAN this unit will be visible on the local Network and the following parameters need to be configured See LAN proto
11. 3 Auto Alignment Tracking Phase Picture position Hor Vert Picture Position Horizontal Vertical Aspect Video only if 3D only 16 9 is available 4 3 16 9 Zoom Aspect PC only Auto 1 1 Full Mask 5 2 5 Off Custom Left 0 5 Right 0 5 Upper 0 5 Down 0 5 Progressive 480i 576i 1080i Auto Off 3D Setting 3D format Auto Side by Side Top amp Bottom 2D 2D to 3D Conversion On Off Parallax 15 15 Crosstalk Cancel 8 8 Intensity 5 5 Subtitle Adjust On Off R699820 Yunzi Series User Manual 23 6 0 MENU STRUCTURE 24 Installation Lens Control Focus Zoom Shift Image Pattern On Off Lock On Off Lens Memory Select Lens Memory Save Lens Memory Name Edit 10 char max Lens Center Confirm Lens Cover Yunzi 2 amp 3 Auto Open Pixel Adjust Adjust On Off Adjust Area Whole Zone Adjust Color Red Blue Adjust Pattern Color White Cyan Yellow Adjust Pixel Adjust Fine Reset Installation Installation Style Front Ceiling Mount Front Rear Ceiling Mount Rear Keystone disable with 3D signal Horizontal 40 40 Vertical 30 30 Pincushion disable with 3D signal 20 20 Anamorphic Off vert stretch A hor squeeze B Screen Adjust A B C Yunzi 1 Color Profile must be On 001 105 Yunzi 2 amp 3 Environment Setting Environment Setting On Off Screen Size inch dia
12. 31 9 3 Installation Stylei odo ite 32 9 4 sok 32 9 5 33 9 6 PUES ts 33 9 7 USE 552 M 33 9 8 Environment Seting erre oin dida ut aoe e E ese 34 DISPLAY SETUP SET ING iaia 34 11 0 FUNCTION SETTINGS alla 34 11 1 Misi busi uae 34 11 2 lt O Ime EL e A C 34 113 High Altitude alal cali Aia aan e thee lina ili 34 E MEOS DIT rano 35 11 5 Communication Terminali Si ait ete RE B dc esd ee 35 Network O E et 35 117 RemoteiCode A of Bric ihrer te deste e pe teste beds anit da ca eed eek to eee unge nera eu 35 1 8 c peso teo roa eee Hi Ur OE ier rei nd tures etis eres reu ad 35 12 0 INFORMATION MENU rie 35 CINEMASCOPE SETUPS o soi sona irrita 36 13 1 Lens Zoomior Theater System Kits asics aec aaa toten areali 36 13 2 Cm mascope setup with Lens ii 36 13 3 Installing a 2 35 1 screen with the Theater System 36 d op EN 37 14 l Clean Dmtonthe Cabinet zem ertet e Eri qr iet esee 37 142 Ee ae E ERU FUE OH DB REGES 37 143 Replacing the o terere eee ep ee AE Ere ER Dein 37 14 4 Cleaning and Replacing t
13. 5 globally or for each side of the screen 8 7 Progressive only 480i 576i 1080i Interlaced signals are converted to progressive signals using video images from the surrounding This function is only available for interlaced input signals 480i 576i and 1080i 8 8 3D Setting 30 3D Formats Use this function to choose the correct 3D input format Some input signals may contain 3D data such as 1080p Side by Side but encoded as if they were in 2D This unit may treat them as standard 2D signals and will not project correctly In such cases configure the signal manually between Side by Side Top amp Bottom and 2D In other cases you may select Auto setting 2D to 3D Conversion You can use the 2D to 3D Conversion to convert 2D pictures into a quasi 3D picture The quality of the result may differ from quality of original 2D picture Turn it On or Off Parallax Use this function to adjust the amount of misalignment of the left and right 3D video images Adjust settings according to your preference between 15 and 15 e parallax is an important parameter for 3D movies that directly affects comfort during 3D projection It is admitted that generally the maximum value of the parallax must not exceed 6 5 cm which is an average value of people s distance between their left and right eyes and because the parallax value changes with the screen size it is important to set this parameter to a value with which everyone feels comfo
14. Command 52h 43h 52h 43h Data 37h 33h 30h 35h 37h 33h 30h 36h Description Switch the unit ON Switch this unit into Stand by mode Switch input Keypad 52h 43h 52h 43h 37h 33h 30h 38h Switch to next input 37h 33h 34h 36h Switch active input to VGA 37h 33h 34h 44h 37h 33h 37h 30h 37h 33h 37h 31h 37h 33h 30h 31h Switch active input to Component Switch active input to HDMI 1 Switch active input to HDMI 2 37h 33h 30h 32h 37h 33h 30h 33h 37h 33h 32h 45h 37h 33h 32h 46h 37h 33h 33h 34h 37h 33h 33h 36h LEFT Hide Display OSD Position Picture Mode Color Profile Yunzi 1 52h 43h 52h 43h 52h 43h 50h 4Dh 50h 52h 37h 33h 31h 44h Toggle Hide ON OFF 37h 33h 44h 30h Switch Hide to ON 37h 33h 44h 31h 37h 33h 34h 32h 37h 33h 36h 36h 37h 33h 36h 37h Switch Hide to OFF Toggle the OSD position Animation Mode Stage 37h 33h 36h 38h Cinema Mode 37h 33h 36h 39h Film Mode 37h 33h 36h 41h 37h 33h 38h 37h 37h 33h 36h 46h 37h 33h 36h 43h Natural 3D THX User 1 37h 33h 36h 44h User 2 37h 33h 36h 45h User 3 37h 33h 43h 41h 37h 33h 43h 42h 31h 36h 31h 37h User 4 User 5 Standard Film 31h 38h Cinema R699820 Yunzi Series User Manual 15 0 MISCELLANEOUS Color Profile Yunzi 1 Color Profile Yunzi 2 amp 3 Set User1 name Set User2 name Set User3 name 50h 4Dh 50h 5
15. Film Cinema Animation Natural Stage 3D mode Color Film Cinema Anime Natural Stage 3D Profiles Standard Standard Standard Standard Standard Standard Yunzi 2 amp 3 Color Profiles Video Movies Digital Cinema Animation ADIY Live Concerts i or vivid Dramas 3D sources THX sources Source in general or HDTV or Spectacles movies or Videos Picture Film Cinema Animation Natural Stage 3D mode Cinema1 Anime1 Stage 3D Cinema Color Film2 Cinema2 Anime2 Vivid Standard 3D Video Profiles Standard Standard AdobeRGB G Yunzi 2 amp 3 have an additional THX picture mode to obtain a non over saturated colors in a dark environment This picture mode is optimized for dark rooms There are 16 Color profiles depending on the picture mode you may choose an available color profile preset Film1 available with Film Picture Profile uses the Xenon filter and adjusted to Eastman Kodak film tone Film2 available with Film Picture Profile uses the Xenon filter and adjusted to Fujifilm film tone Film3 available with Film Picture Profile uses the Xenon filter and adjusted to Technicolor film tone Standard will bring rich and saturated colors available with almost any selected Picture Mode Cinema1 available with Cinema Picture Profile and adjusted to HDTV standards Cinema2 available with Cinema Picture Profile and adjusted to DCI standards Anime1 best suited to Hollywood animes Anime2 best suited to Japanese animes Video color profile is best suited to
16. are commissioned operated incorrectly or if after the transfer of risks the goods are subject to influences not agreed upon in the contract all guarantee claims of the purchaser will be rendered invalid Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser e g interfaces Normal wear as well as normal maintenance are not subject to the guarantee provided by Dreamvision either The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer Trademarks Brand and product names mentioned in this manual may be trademarks registered trademarks or copyrights of their respective holders All brands and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products of their manufactures R699820 Yunzi Series User Manual 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 TABLE OF CONTENTS SAFETY INSTRUCTIONS udis ka dvd ko a bd a a k add n 5 1 1 Important Infotmatiofi ia E 5 1 2 Important Sale Suards 5 1 3 Regional Specific Infor at Once arie alal aa 7 INSTALLATION GUIDELINES esix xdetkbd ect Exo has vip dock nk n kk vk do kk 8 2 1 About 3D Content and 3D Projection aci
17. connect an external IR receiver when this unit is used in a dedicated box or in rear projection setup DC power supply output 12V 140 300mA to control either a screen or an anamorphic slider Automation Device Control Device or Computer with RJ 45 USING RS 232 WITH A COMPUTER The RS 232 Control and Automation may require specific software and tools See RS 232C protocol page 40 for more details on RS 232 cabling and protocol USING LAN WITH A COMPUTER When the LAN Control is selected the RS 232 port cannot be used for automation In addition the control device must send specific functions to this unit using the Local Network this is not a web interface See LAN protocol page 46 for more details on the network configuration and protocol I CONNECTING AN AUTOMATION CONTROL DEVICE This unit can control or be controlled by using several input output terminals Each terminal is ruled by specific protocols Please refer to Appendix for more information R699820 Yunzi Series User Manual 6 0 MENU STRUCTURE 6 0 MENU STRUCTURE MAIN MENU SUBMENU AVAILABLE OPTIONS Picture Adjust Picture Mode Movies Film 6 5 User Digital Cinema Cinema SF movies or animes Animation Video programs Natural Concerts Stage 3D User1 User2 User3 User4 User5 Add Picture Modes Yunzi 2 amp 3 THX for expert users require THX bright 3D animations 3D Animation individual calibra
18. effects on the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more information about collection point and recycling of this product please contact your local municipal office your household waste disposal service or the shop where you purchased the product Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation Other Countries outside the European Union If you wish to dispose of this product please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment About the installation place Do not install the projector in a place that cannot support its weight securely If the installation place is not sturdy enough the projector could fall or overturn possibly causing personal injury CAUTION To reduce the risk of electric shock do not remove cover Refer servicing to qualified service personnel This projector is equipped with a 3 blade grounding type plug to satisfy FCC rule If you are unable to insert the plug into the outlet contact your electrician WARNING To prevent fire or shock hazards do not expose this appliance to rain or moisture This apparatus must be earthed 1 2 Important Safeguards Electrical energy can perform many useful functions This unit has been engineered and manufactured to assur
19. shift Lens Shift Right 52h 43h 37h 33h 34h 33h Shift the picture to the right using lens shift Lens Shift Left 52h 43h 37h 33h 34h 34h Shift the picture to the left using the lens shift Lens Focus 52h 43h 37h 33h 33h 31h Focus far Lens Focus 52h 43h 37h 33h 33h 32h Focus near Lens Zoom T 52h 43h 37h 33h 33h 35h Zoom Wide Lens Zoom W 52h 43h 37h 33h 33h 37h Zoom Tele Lens Aperture 52h 43h 37h 33h 32h 30h Toggle the Lens Aperture setting menu Lens Aperture 52h 43h 37h 33h 31h 45h Increase the Lens Aperture value Lens Aperture 52h 43h 37h 33h 31h 46h Decrease the Lens Aperture value Lens Cover 52h 43h 37h 33h 32h 44h Unsynchronizes Lens Cover with HIDE function 37h 33h 32h 43h Synchronizes Lens Cover with HIDE function 37h 33h 31h 41h Open Lens Cover 37h 33h 31h 39h Close Lens Cover Keystone 52h 43h 37h 33h 31h 42h Vertical Keystone Vertical Keystone Horizontal Keystone Horizontal Keystone Lens Memory 52h 43h 37h 33h 44h 34h Switch between lens memories Lens Memory select Set Memory1 name Set Memory2 name 52h 43h 49h 4Eh 4Dh 31h 49h 4Eh 4Dh 32h 37h 33h 44h 38h Select Lens Memory 1 37h 33h 44h 39h 37h 33h 44h 41h 37h 33h 45h 35h 37h 33h 45h 36h Select Lens Memory 2 Select Lens Memory 3 Select Lens Memory 4 Select Lens Memory 5 37h 33h 44h 41h Select Lens Memory 9 37h 33h 45h 42h 10 ASCII char 10 ASCII char Select Lens Memory 10 Set custom name to L
20. value between 50 and 50 7 8 Color The Color function or Saturation is used to adjust the saturation levels Adjust the Color value between 50 and 50 7 9 Tint The hue function is used to adjust the color tint to obtain true color reproduction Adjust the Tint value between 50 more red and 50 more green 7 10 Advanced Picture Settings Multiple Pixel Control Level MPC Level 4k Profile Choose between Film or High Resolution for Blu Ray Movies or HD programs SD for standard definition movies such as DVDs Dynamic for a greater perception of the 4k Interpolation processing Off to switch the 4k Interpolation Off Fine Tuning picture enhancement by adjusting the three following effects a Enhance enhances the sharpness of foreground objects detected in the picture b Dynamic Contrast enhances the general contrast of the picture c Smoothing enhances the blurriness of backgrounds for increased the global sense of depth Analysis screen nalysis screen You can enlight the different areas processed by the 4K Interpolation by pressing twice MPC Level button on the RCU when browsing the MPC Level sub menu Areas affected by the Enhance parameter are colored Blue and Green Areas affected by the Dynamic Contrast parameter are colored Red and Yellow Areas affected by the Smoothing parameter are colored Black Noise Reduction R699820 Yunzi Series User Manual 27 7 0 PICTURE ADJUST SETTINGS RNR
21. will often require extensive work by a qualified technician to restore the product to normal operation If the product has been dropped or damaged in any way f When the product exhibits a distinct change in performance this indicates a need for service When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or with same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition The product should be placed more than one foot away from heat sources such as radiators heat registers stoves and other products including amplifiers that produce heat When connecting other products such as VCR s and personal computers you should turn off the power of this product for protection against electric shock Do not place combustible behind the cooling fan For example cloth paper matches aerosol cans or gas lighters that present special hazards when over heated Do not look into the projection lens while the illumination lamp is turned on Exposure of your eyes to the strong light can result in impaired eyesight Do not look into the inside of this unit through vents ventilation holes etc Do not look at the illuminat
22. 2h 50h 4Dh 50h 52h 50h 4Dh 55h 31h 50h 4Dh 55h 32h 50h 4Dh 55h 33h 31h 39h Anime 31h 41h Natural 31h 42h Stage 31h 43h 3D 31h 44h Off 30h 30h Off 30h 31h Film1 30h 32h Film2 31h 33h Film3 30h 33h Standard 30h 34h Cinema1 30h 35h Cinema2 30h 36h Anime1 30h 37h Anime2 30h 38h Video 30h 39h Vivid 30h 41h Adobe 30h 42h Stage 30h 43h 3D Cinema 31h 34h 3D Video 31h 35h 3D Anime 30h 44h THX 30h 45h Custom1 30h 46h Custom2 31h 30h Custom3 31h 31h Custom4 31h 32h Custom5 10 ASCII char Set custom name to User1 Picture Mode 10 ASCII char Set custom name to User2 Picture Mode 10 ASCII char Set custom name to User3 Picture Mode Set User4 name 50h 4Dh 55h 34h 10 ASCII char Set custom name to User4 Picture Mode Set User5 name 50h 4Dh 55h 35h 10 ASCII char Set custom name to User5 Picture Mode Picture Adjust Gamma 52h 43h 52h 43h 37h 33h 37h 32h 37h 33h 37h 35h 37h 33h 33h 43h 37h 33h 33h 44h Toggle Picture Adj menu Toggle Gamma function menu Set Gamma to Custom1 Set Gamma to Custom2 37h 33h 33h 45h Set Gamma to Custom3 Color Management Expert Calibration THX Expert Calibration ISF Set Calibrator name Contrast 52h 43h 52h 43h 52h 43h 50h 4Dh 43h 49h 52h 43h 37h 33h 36h 30h Set Color Management to Off 37h 33h 36h 31h 37h 33h 36h 32h 37h 33h 36h 33h 37h 33h 43h 3
23. 6h Set Color Management to Custom1 Set Color Management to Custom2 Set Color Management to Custom3 Switch to Adjust mode 37h 33h 43h 37h THX plus Off 37h 33h 43h 38h THX plus On 37h 33h 38h 35h 37h 33h 38h 36h 37h 33h 35h 38h 37h 33h 35h 41h Switch Picture Mode to THX Bright Switch Picture Mode to THX Dark Switch to Adjust Mode ISF Off 37h 33h 35h 42h ISF On 37h 33h 36h 34h Switch Picture Mode to ISF Day 37h 33h 36h 35h 18 ASCII char 37h 33h 37h 38h 37h 33h 37h 39h Switch Picture Mode to ISF Night Set Calibrator name ISF must be in Adjust Mode Contrast Contrast R699820 Yunzi Series User Manual 43 15 0 MISCELLANEOUS 44 Brightness 52h 43h 37h 33h 37h 41h Brightness 37h 33h 37h 42h Brightness Color 52h 43h 37h 33h 37h 43h Color 37h 33h 37h 44h Color Tint 52h 43h 37h 33h 39h 38h 37h 33h 39h 39h Tint Random Noise 52h 43h 37h 33h 30h 42h RNR Reduction 37h 33h 30h 43h RNR Block Noise 52h 43h 37h 33h 31h 30h BNR switch to OFF Reduction 37h 33h 30h 46h IBNR switch to ON Mosquito Noise Reduction 52h 43h 37h 33h 30h 44h 37h 33h 30h 45h MNR Clear Motion Drive HDMI CEC 52h 43h 52h 43h 37h 33h 34h 37h CMD switch to OFF 37h 33h 38h 41h Toggle CMD Mode 37h 33h 34h 38h 37h 33h 34h 39h 37h 33h 34h 41h 37h 33h 35h 36h CMD switch to Low CMD switch to High CMD s
24. D Parallax to 6 Set 3D Parallax to 2 Set 3D Parallax to 1 30h 30h 30h 30h Set 3D Parallax to 0 30h 30h 30h 31h Set 3D Parallax to 1 30h 30h 30h 39h 30h 30h 30h 41h 30h 30h 30h 42h Set 3D Parallax to 9 Set 3D Parallax to 10 Set 3D Parallax to 11 R699820 Yunzi Series User Manual 15 0 MISCELLANEOUS 3D Parallax 49h 53h 4Ch 56h 30h 30h 30h 46h Set 3D Parallax to 15 Pincushion Env Correction 49h 4Eh 44h 49h 49h 4Eh 53h 45h 46h 46h 45h 43h Set Pincushion to 20 30h 30h 31h 34h Set Pincushion to 20 Set Env Correction to OFF Set Env Correction to ON Screen Size 49h 4Eh 53h 53h Set Screen Size to 60 inches Set Screen Size to 150 inches Set Screen Size to 160 inches Set Screen Size to 200 inches Viewing Distance Wall Color Lamp Power 49h 4Eh 56h 44h 49h 4Eh 57h 43h 50h 4Dh Set Viewing Distance to 1 m 4Ch 50h 30h Set Viewing Distance to 10 m Set Wall Color to Dark Set Wall Color to Light Set lamp to Normal 4Ch 50h 31h Set lamp to High Lens Control 37h 33h 31h 43h 37h 33h 34h 30h 37h 33h 34h 31h Header 21h Command Data Description Lens Menu 52h 43h 37h 33h 33h 30h Lens Menu Toggle the Lens Menu Lens Shift Up 52h 43h 37h 33h 32h 31h Shift the picture upward using lens shift Lens Shift Down 52h 43h 37h 33h 32h 32h the picture downward using lens
25. GS 8 0 INPUT SIGNAL SETTINGS 8 1 HDMI Inputs This menu is available if the selected active input is HDMI1 or HDMI2 Input Auto The input dynamic range is automatically detected and configured Standard Force dynamic range to 16 235 Enhance Force dynamic range to 0 255 Super White Force dynamic range to 16 255 Check Input Levels The following pattern is overlaid to current picture to confirm that the correct input level has been selected 0 16 Use the Input Levels pattern to confirm the correct HDMI dynamic range setting Color Space Auto The source color space is automatically detected and configured YCbCr 4 4 4 Set color space to YCbCr 4 4 4 YCbCr 4 2 2 Set color space to YCbCr 4 2 2 RGB Set color space to RGB 4 4 4 Control with HDMI CEC Off By default the CEC communications are disabled On Enables CEC communications to be sent to the projector through HDMI cable CEC stands for Consumer Electronic Control 8 2 Component This menu is available if the selected active input is Component Y Pb Cb Pr Cr Select this option if the COMP input is connected to a component video signal RGB Select this option if the COMP input is used with a RGB video source 8 3 Yunzi 2 8 3 only This menu is available if the selected active input is PC Sub D15 input Auto Alignment Automatically adjusts Tracking Phase and Picture Position Tracking Adjust the horizontal size and display a
26. RL E HIGH CONTRAST VIDEO PROJECTOR User Manual 2 2 ACTIVE 30 N f ream Jision WE MAKE THE WORLD DREAM Changes Dreamvision provides this manual as is without warranty of any kind either expressed or implied including but not limited to the implied warranties or merchantability and fitness for a particular purpose Dreamvision may make improvements and or changes to the product s and or the program s described in this publication at any time without notice This publication could contain technical inaccuracies or typographical errors Changes are periodically made to the information in this publication these changes are incorporated in new editions of this publication Copyright All right reserved No part of this document may be copied reproduced or translated It shall not otherwise be recorded transmitted or stored in a retrieval system without the prior written consent of Dreamvision Guarantee Dreamvision provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee On receipt the purchaser must immediately inspect all delivered goods for damage incurred during transport as well as for material and manufacturing faults Dreamvision must be informed immediately in writing of any complaints If the purchaser or third party caries out modifications or repairs on goods delivered by Dreamvision or if the goods are handle incorrectly in particular if the systems
27. Random Noise Reduction You can set it from 0 up to 16 to reduce the picture random noise MNR Mosquito Noise Reduction function is used to reduce the Mosquito noise on the picture generally found in compressed digital video signals such as television broadcast or encoded movies Adjust the MNR value from 0 up to 16 to reduce the typical broadcast picture mosquito noise BNR Block Noise Reduction uses a large portion of the picture to reduce the digital noise this ensures a higher quality filter Adjust the BNR value to On or Off Color Management TSL adjustments The Color Management gives the installer an unique calibration ease with the integrated Color Adjustment menu each primary secondary colors and orange can be independently calibrated to obtain a precise color balance in a snap Adjust the Red Green Blue Yellow Cyan Magenta and Orange Tints their saturations and luminances and store them into Custom1 Custom2 or Custom3 profiles User Name Edit You can edit the picture modes names User1 to 5 using a maximum length of 10 characters You can use alphabet letters numbers and symbols Picture Adjust f w gt gt User Name Edit Select cursor Exit MENU Selec Operate 8 BACK a Select the user name you want to edit from User1 to User5 Press OK to enter the edit mode b The input cursor displays the place where the new character will be insert It will move automatically as a c
28. SETUPS 13 1 Lens Zoom or Theater System Kit The Yunzi Series centralizes the controls and automation commands for a unique versatile and unexpectedly simple to operate 2 35 1 theatre experience using Lens Zoom or Anamorphic Lens Up to 10 lens position memories Integrated Constant Image Width CIW scaler with anamorphic mode A and mode B Dedicated commands to control the Theater System Kit and picture size on a 2 35 1 screen 13 2 Cinemascope setup with Lens Zoom Select Menu Installation gt Lens Memory 1 Zoom in until the left and right borders of the picture fits the 2 35 1 screen borders Save the lens position in the lens memory 1 You can also edit the memory 1 name to Cinemascope Select Menu Installation gt Lens memory 2 Make sure to project a 16 9 picture zoom out until the picture top and bottom fit the top and bottom of the screen Adjust the focus and offset if required then save this position into the memory 2 You can additionally edit the memory name to Standard Switch format using the Remote Control Unit You can now switch between Cinemascope and standard formats easily by using the Lens Mem ory button on the RCU and selecting the correct lens memory according to the source format 13 3 Installing a 2 35 1 screen with the Theater System Kit Plug the 12V Trigger output of the projector to the Anamorphic motorization 12V Trigger to anamorphic motorization
29. TV and Sport programs Vivid color profile is best suited to video games entertainment AdobeRGB color profile adjusted to Adobe RGB standard Stage best suited to live concert 3D Cinema best with DCI movies in 3D R699820 Yunzi Series User Manual 25 7 0 PICTURE ADJUST SETTINGS 7 2 3D Video best with HDTV programs in 3D 3D Animation best with 3D animations THX dedicated color preset for THX profiles Off switches off the color profiles Color Temperature 73 Color temperature stands for the spectral properties of a light source Low color temperature implies warmer ambiance more yellow red while high color temperature implies a colder light more blue Depending on the Picture Profile selected this setting can be set to Preset from 5500K warm colors up to 9500K cold colors in steps of 500K 1 uses the Xenon filter and color compensation to reproduce a film projector Xenon2 uses the Xenon filter and color compensation to reproduce a digital cinema projector Xenon3 same as Xenon2 but within a cooler temperature High Brightness used for maximum brightness output available Custom1 Custom2 and Customs can be used to adjust color temperature to specific environment A Custom setting allows a fine adjustment of a Color Temperature by selecting it in the Correction Value menu Adjust the Gain values bright part and Offset values dark part for each color Red Green a
30. acing the lamp unit pull out the power plug from the outlet and wait until the STANDBY ON led is still light red Replacing a lamp with the plug connected to the outlet may cause injuries or electric shocks Procedure for Lamp Replacement During the lamp replacement process you may have access to sensitive parts of the projector Loosen the screw on the lamp trap at the rear of this unit Pull out the lamp unit using the handle Insert the new lamp unit until it is firmly in place Tighten the screws of the lamp unit Attach the lamp cover and fasten the lamp trap screw Resetting Lamp Time After installing a new lamp reset the lamp time using the OSD menu 699820 Yunzi Series User Manual 14 0 MAINTENANCE a Turn On the unit b Browse into the menu Function gt Reset Lamp Time c Confirm time reset Alternative method in standby mode using the remote control a Plug this unit to Main power b When the projector is in standby mode red STANDBY ON led use the remote control and press sequentially the BACK OK HIDE within 1 second interval then DOWN for at least 2 seconds c The sequence is successful if the STANDBY ON and LAMP leds blink alternately for 3 seconds CAUTION DURING RESET Reset the lamp time only when you have replaced the lamp Never reset it when the lamp is still in use Otherwise the approximate standard for gauging replacement time may be inaccurate lamp performance ma
31. an cause electric discharges 18 R699820 Yunzi Series User Manual 5 0 CONNECTIONS 5 2 Connecting a Video Source to the Projector HDMI 1 LJ vpppr Ej ui or RGB HDMI 2 3 EP 000 O O EP 00 c O 3D Syncro VGA Emitter c amp ao Sub 0 15 Connection Device HDMI1 HDMI2 HDMI or DVI D sources Blu Ray Disc player DVD player with HDMI Game v1 4a with M3 lock hole Console Computer with DVI D output 3D Synchro output YPbPr or RGB 3x RCA 3D synchro emitter to control active shutter glasses 3 PIN mini DIN interface 12V DVD Player HDTV Receiver Game Console SD or HD DVB T receiver Multimedia box Analog Camera VGA Sub D 15 Yunzi 2 amp 3 only For Yunzi 2 amp 3 Computer Multimedia box using their VGA output D Make sure to use a certified HDMI cable especially when the distance between the different devices are longer than 5 meters If it is the case the use of a split system or optical fiber cable is highly recommended R699820 Yunzi Series User Manual 5 0 CONNECTIONS 5 3 Connecting an Automation or Control device 20 LAN to Rooter for Automation T RS 232C for Automation Optional IR receiver 12V Trigger Connection RS 232C Device Automation Device Control Device or Computer with RS 232 capability Optional IR receiver 12V Trigger LAN Can be used to
32. ance on 2 35 screen O LO 16 9 format O O 16 9 on 2 35 screen E uas 2 35 1 format O uas 2 35 2 35 When the source switches format press Anamo button to obtain the correct anamorphic mode 14 0MAINTENANCE 14 1 Clean Dirt on the Cabinet Always use a soft cloth In case of heavy soiling soak a cloth in neutral detergent diluted with water wring dry and wipe followed by wiping again using a dry cloth Caution Pay attention to the following as the cabinet may deteriorate in condition get damaged or paint may come off Do not wipe with a stiff cloth Do not wipe with force Do not wipe with thinner or benzene Do not spray volatile chemicals like insecticide Do not allow prolonged contact with rubber or plastic products 14 2 Dirt on the Lens The lens shall be cleaned using commercial blowers or lens cleaning papers for cleaning glasses and cameras Do not use fluid type cleaning agents This may lead to peeling of the surface coating film The lens surface is fragile Avoid rubbing it hard or knocking 14 3 Replacing the Lamp R699820 Yunzi Series User Manual 97 14 0 MAINTENANCE Light source Lamp and Lamp Usage Time The life of light source lamps used for this unit is about 4000 hours when running this unit in low lamp mode When the lamp power is set to Low the lamp is approximately 4000 hours Thi
33. ceive PU_OK 50h 4Ah 5Fh 4Fh 4Bh send PJREQ 50h 4Ah 52h 45h 51h receive PJACK 50h 4Ah 41h 43h 4Bh send Anamorphic A 21h 89h 01h 52h 43h 37h 33h 32h 33h 0Ah receive confirmation 06h 89h 01h 52h 43h 0Ah after 5 sec TCP connection is closed Switch Anamorphic to mode A OGC ROD 15 3 Infra Red long hex pronto compatible RCU The infra red command must be sent using NEC 5 protocol in ASCII format In the following example Power ON command is 37h 33h 30h 35h this command has to be converted as ASCII it becomes 73 05 To send this command using long hex Pronto compatible convert the ASCII code as two hexadecimal numbers as follow Code A 73h 115 for code B 63h 99 replace 115 by 99 05h 5 Then program the Pronto RCU using the Device number 115 and Function 5 Device Code 115 0x73 Function 5 0x05 0000 006D 0001 0011 0141 00A0 0014 003C 0014 003C 0014 0014 0014 0014 0014 003C 0014 003C 0014 003C 0014 0014 0014 003C 0014 0014 0014 003C 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014 0336 A complete device function chart with their corresponding long hex commands is available ask your dealer if required R699820 Yunzi Series User Manual 47 15 0 MISCELLANEOUS 15 4 Specifications 48 Overview The Yunzi Series uses the latest technology developed to provide the ultimate video projection experience LCoS Liquid Crystal on Silicon technology based on a reflective pri
34. col page 46 for more details 11 7 Remote Code A or B Select in the projector menu the code A or B according to the code selected on the RCU You can change the code used by the RCU to communicate with the projector from A to B To do so press and hold for 3 sec simultaneously MENU BACK buttons on the RCU All the buttons on the RCU will blink Two blinks indicate that B code is used Three blinks indicate that A code is used 11 8 Lamp Reset Resets the lamp use time to 0 during the lamp replacement procedure See Replacing the Lamp page 37 for more details 12 0 INFORMATION MENU Input Terminal Displays the active video input Input Source Format Displays the type of the current video input signal If PC input is selected this item cannot be displayed Deep Color Depth Display the bit depth color depth of the video signals input from the HDMI terminals Deep Color is not displayed for YCbCr 4 2 2 signals Resolution If the active input is PC input its resolution is displayed H Freguency In the case of PC signal the horizontal freguency is displayed V Freguency In the case of PC signal the vertical freguency is displayed Lamp Time Displays the accumulated hours of usage of the lamp Calibrator Stores up to 18 ASCII characters set by the Calibrator Shown only if set during ISF profile adjustment R699820 Yunzi Series User Manual 35 13 0 CINEMASCOPE SETUPS 13 0CINEMASCOPE
35. configure the lens to the save settings Lens Memory Save Store into an available memory the lens focus zoom and shift configuration There are 5 memories for Yunzi 1 and 10 memories for Yunzi 2 amp 3 Lens Memory Name Edit You can edit the Lens Memory Name within the limit of 10 characters Same procedure as Section User Name Edit page 28 Lens Center Reset the lens position to the original central position Lens Cover Yunzi 2 amp 3 Control the behavior of the Lens Cover Auto the lens cover opens or closes when the projector switches On or Off Open the lens cover is always open 9 2 Pixel Adjust R699820 Yunzi Series User Manual 3l 9 0 INSTALLATION SETTINGS The pixel adjustment is extremely fine each color can be adjust within 1 16 pixel steps on 121 individual adjustment zones Adjust Enable the pixel adjustment On or Off Adjust Area Whole the entire screen is selected for adjustment Zone the screen is divided into 121 adjustment zones Adjust Color Select the color to adjust Red or Blue Adjust Pattern Color Select a pattern to help the pixel alignment Settings White or Green adjusting Color Yellow for red Cyan for blue Adjust Pixel This function is enable when the Adjust Area is set to Zone only You can adjust the selected color position horizontally and vertically by 1 pixel steps H settings 2 2 V settings 2 2 Adjust Fine Use this function to move the se
36. creen and environment R699820 Yunzi Series User Manual 33 10 0 DISPLAY SETUP SETTINGS 9 8 Environment Setting To finely tune the picture setting you may change the environment settings so that they match your installation Screen size diagonal size in inches set this setting between 60 and 200 Viewing distance is the distance to the screen of the nearest seat in meters set it between 1m and 10m Wall color select Dark if the walls are black or similar for any lighter shades select Light 10 0DISPLAY SETUP SETTINGS Back Color Configures the screen color displayed when there is no active input Set to Blue or Black Menu Position Upper left Upper right Center Lower right Lower left Menu Display 15sec Display menu for 15 seconds before fade out On Always display menu Line Display 5sec Display the input settings for 5 seconds after input selection Off Don t display Source Display On Display the source of the input signals after input selection Off Don t display Logo On Display D ILA logo during startup for 5 seconds Off Don t display Language Choose the OSD language between English Japanese German Spanish Italian French Portuguese Dutch Swedish Norwegian Russian and Chinese 11 0FUNCTION SETTINGS 11 1 Trigger The 12V trigger output can be used to control any compatible devices such as motorized screens or anamorphic kits The 12V trigger output is
37. cture double check that the larger one does not exceed the zoom capacity R699820 Yunzi Series User Manual _ 18 3 0 REMOTE CONTROL UNIT RCU 3 0 REMOTE CONTROL UNIT RCU 3 1 General View Stand By button Power On button Select Active Input Select 3D Format Anamo rphic mode Select PC Input TENS Lens Ap erture LENS Lens control m Shift Betas and C M D Clear Motion Drive Select a Lens Memory Display 3D Setting menu Hide Display Backlight button Navigation buttons Confirm button Display Menu Back to previous menu PICTURE MODE Select a Picture Mode User Picture mode C M D Clear Motion Drive THX Picture mode Gamma Adj M P C 4k Interpolation Basic Picture Adj Color temp Adj Color Profile 3 2 Loading and replacing batteries Push the cover tab with the fingernail a little backwards and pull upwards the cover top Slide the cover forward to remove Push the battery body towards the spring and lift up to remove Insert two AAA size batteries making sure the polarities match the and marks inside the battery compartment Insert the lower tab of the battery cover in the gap at the bottom of the remote control and press the cover until it is firmly closed 14 R699820 Yunzi Series User Manual 3 0 REMOTE CONTROL UNIT RCU CAUTION WHEN USING BATTERIES Do not mix new and old batteries Do not mix different type of batt
38. e your personal safety But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD In order not to defeat the safeguards incorporated into this product observe the following basic rules for its installation use and service The power input is auto ranging from 100 to 240 VAC Please read these Important Safeguards carefully before use All the safety and operating instructions should be read before the product is operated All warnings on the product and in the operating instructions should be adhered to All operating instructions should be followed Place the projector near a wall outlet where the plug can be easily unplugged Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use attachments not recommended by the product manufacturer as they may be hazardous Do not use this product near water Do not use immediately after moving from a low temperature to high temperature as this causes condensation which may result in fire electric shock or other hazards R699820 Yunzi Series User Manual 5 Do not place this product on an unstable cart stand or table The product may fall causing serious injury to a child or adult and serious damage to the product The product should be mounted according to the manufacturer s instructions and should use a mount recommended by the manufacturer When the produc
39. e e EH EHE ERA E Reb endo 8 2 2 THX 3D Display Certification Yunzi 2 463 2220 1 cete tn sek dedu 8 2 3 Comfort and Caution with 3D Content riae ie tee eet Eden 9 2 4 3D Synchro Emitter and 3D Glasses i 9 2 5 Best seat position for 3D projection inet en HER ei 9 2 6 Evironment aeea eei ai eE ETE E E SE E a A E 10 27 Air Flow and Space Requirements cse ie e Reden 10 2 8 Ceiling Mounting the Unit re ica 11 2 9 Projection Distance aaa HR eR HE E HERE REIHEN 11 2 10 Setting the Lens and using Lens Memories enne 12 REMOTE CONTROL UNIT GROW sazia 14 3 1 General M 14 3 2 Loading and replacing batteries ii 14 33 How tousethe Remote Control Unit Lace iets dina Priest pipi e b ae 15 GETTING SIARIED alia 16 4 1 eura de H 16 4 2 Connecting the Power e tib sr t eerte tug 17 4 3 Operating LEDS itai p i Ee e 17 4 4 Operating and Navigation Buttons sirensis saii soir Sairi Eia 18 CONNECTION erc 18 5 1 Caution when connecting a device to HDMI input 18 5 2 Connecting a Video Source to the Projector i 19 5 3 Connecting an Automati
40. ens Memory1 Set custom name to Lens Memory2 Set Mem9 name 49h 4Eh 4Dh 39h 10 ASCII char Set custom name to Lens Memory9 R699820 Yunzi Series User Manual 45 15 0 MISCELLANEOUS Set Mem10 name 49h 4Eh 4Dh 41h 10 ASCII char Set custom name to Lens Memory10 Examples You want to Command to send send 21h 89h 01h 50h 57h 31h 0Ah receive 06h 89h 01h 50h 57h 0Ah send 21h 89h 01h 50h 57h 30h 0Ah receive 06h 89h 01h 50h 57h 0Ah send 21h 89h 01h 49h 50h 32h 0Ah Change Active Input to Comp or send 21h 89h 01h 52h 43h 37h 33h 34h 44h 0Ah send 21h 89h 01h 52h 43h 37h 33h 32h 45h 0Ah receive 06h 89h 01h 52h 43h 0Ah send 21h 89h 01h 49h 4Ch 4Dh 31h OAh receive 06h 89h 01h 49h 4Ch 4Dh 31h send 54h 56h 2Dh 73h 69h 7Ah 65h 20h 20h 20h receive 06h 89h 01h 49h 4Ch 4Dh 31h Switch the projector ON Switch the projector OFF Display On Screen Menu Change Lens Memory1 name to TV size unused characters are filled with space 20h Available Reference and Response commands A reference command ask the projector about its status Header Command Description Response Data Power status 50h 57h Check the Power status 30h Standby header 3Fh 31h Power On 32h Cool Down 34h Warning Active Input 49h 50h Check which input is active 30h S video header 3Fh 31h Video 32h Component 33h VGA 36h HDMI 1 37h HDMI 2
41. eries as they are different in characteristics Insert batteries according to the and marks on the battery case Do not put batteries into fire or recharge them if they are not design to Remove the batteries if the remote control is not to be used for a prolonged period Use manganese batteries wherever possible Do not use rechargeable batteries NOTICE If the remote control has to be brought closer to the projector to operate it means that the batteries are wearing out When this happens replace the batteries Insert the batteries according to the and marks 3 3 How to use the Remote Control Unit The operable distance of the remote control unit is about 7m for direct reception and within 30 angle with respect to the sensor Front InfraRed sensor Back InfraRed sensor The remote control unit can be used by having the transmission signal reflected off a screen as the effect of signals reflected from the RCU differ with the type of screen used operable distance may decrease R699820 Yunzi Series User Manual 15 4 0 GETTING STARTED 4 0 GETTING STARTED 4 1 General View Front side Optical Lens amp Lens cover p Air Outlet Operating LED Front IR sensor Optical Lens amp Lens cover The lens cover on model Yunzi 2 amp 3 is motorized Operating LEDs see section 4 3 page 17 for more details Air Outlets see Air Flow and Space Requirements page 10 Rear side Input Panel Lamp t
42. g 60 200 Viewing Distance 1m 10m Wall Color Light Dark Display Setup Back Color Blue Black Menu Position select position Menu Display 15sec On Line Display input setting 5sec Off Source Display active input On Off Logo On Off Language Select between 12 languages Function Trigger Off On Power On Anamorphic Off Timer in hours 1H 2H 3H 4H Off High Altitude Mode On Off ECO Mode On Off Communication Terminal RS 232C LAN Network LAN must be selected DHCP Client On Off IP Address 192 168 0 2 Subnet Mask 255 255 255 0 Default Gateway 192 168 0 254 Mac Address Display MAC Set Display Network settings Remote Code B Lamp Reset Confirm R699820 Yunzi Series User Manual 7 0 PICTURE ADJUST SETTINGS Information Input Terminal Input Source Format Deep Color Depth PC Resolution PC H Freq PC V Freq Deep Color Depth Lamp Time Software Version 7 0 PICTURE ADJUST SETTINGS 7 1 Picture Modes and Color Profiles The preset Picture Modes are available and they can be applied to any input A picture mode retains the picture adjustments When adjusting the Picture Mode you can also select pre configured Color Profiles Yunzi 1 Color Profiles Video Movies Digital Cinema Animation Dramas Live Concerts 3D Movies Source in general or HDTV or vivid movies or Videos or Spectacles Picture
43. hange the TCP connection port you may use the following RS 232c LAN command 46 _ t r ____ y R699820 Yunzi Series User Manual 15 0 MISCELLANEOUS 4Ch 53 50h 54h 4 ASCII chars as new port address in hexa You want to set TCP port to 10000 Command to send RS 232C Send 10000 as new TCP port value 10000 is 2710h in hexa converted in ASCII characters 32h 37h 31h 30h send 21h 89h 01h 4Ch 53h 50h 54h 32h 37h 31h 30h 0Ah receive 06h 89h 01h 4Ch 53h 0Ah confirm cmd send 21h 89h 01h 4Ch 53h 52h 53h OAh phen reboot Network module receive 06h 89h 01h 4Ch 53h OAh confirm cmd Control Device Projector 1 Opening Connection on port 20554 2 Projector Ready di PJ OK 3 Command Type PJREO Pe 4 Projector Acknowledge PJACK 5 Command 6 Projector confirms After bsec connection is closed LAN communication protocol and timed out Examples You want to Command to send 1 open TCP connection 2 receive PJ OK 50h 4Ah 5Fh 4Fh 4Bh 3 send PUREQ 50h 4Ah 52h 45h 51h Switch the projector ON 4 receive PJACK 50h 4Ah 41h 43h 4Bh 5 6 send Power cmd 21h 89h 01h 52h 43h 37h 33h 30h 35h OAH receive confirmation 06h 89h 01h 52h 43h 0Ah after 5 sec TCP connection is closed open TCP connection re
44. haracter is selected Use UP DOWN LEFT or RIGHT to select a character and press OK to insert it c Press BACK to exit edit mode Clear To delete a character Move the cursor to the desired location and press OK to delete the specific character All Clear To delete all characters OK To save the current name a save confirmation will appear Clear Motion Drive 120Hz The Clear Motion function uses a 120Hz video processing to render a smooth and clear motion for movies shot at 24Hz or HD movies at 60Hz Set the correct level between Off Frame interpolation is disable Low light frame interpolation High strong interpolation Inverse Telecine dedicated interpolation for 60i and 60p sources originally shot in 24p Lens Aperture The lens is eguipped with a variable electronic aperture This function is used to optically adjust the light output depending on the viewing conditions and the light ambiance Adjust from the correct aperture from partially closed to fully opened Lamp Power Set the lamp power used by the current Picture Profile Low lamp is set to 180W High lamp is set to 230W To avoid any damage to the lamp you can t change the lamp power within 90 seconds from the projector startup or 60 seconds after lamp power change 7 11 Reset Picture Profile Prompt a confirmation to reset the current Picture Profile to default settings 28 R699820 Yunzi Series User Manual 8 0 INPUT SIGNAL SETTIN
45. he Dust Filters i 39 145 Troubleshooting eur tette 39 15 0 MISCELLANEOUS lai 40 IE MEME pol 40 15 25 JEAN protocol d ti iz csi otim Beene aloe ave 46 15 3 Infra Red long hex pronto compatible 47 154 SpecHtications uunc ner te Der oil eolie a cete soda pon dial 48 4 a R699820 Yunzi Series User Manual 1 0 SAFETY INSTRUCTIONS 1 0 SAFETY INSTRUCTIONS 11 Important Information Lead free regulation This product has a High Intensity Discharge HID lamp that contains a small amount of mercury It also contains lead in some components Disposal of these materials may be regulated in your community due to environmental considerations For disposal or recycling information please contact your local authorities or the Electronics Industries Alliance http www eiae org Information for Users on Disposal of Old Equipment This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end of life Instead the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment recovery and recycling in accordance with your national legislation By disposing of this product correctly you will help to conserve natural resources and will help prevent potential negative
46. inactive 9 6 Anamorphic Off No modification to original picture Mode A The picture is vertically stretched to fit an installation with anamorphic lens A cinemascope picture is stretched to completely fill the panels without black bands using the optimum resolution and brightness 2 35 SOURCE WITH ANAMORPHIC LENS O O de o o o o O O SDTV 2 35 Off MO o o HDTV 2 35 Off Mode A Anamorphic Mode A Mode B This setting squeezes horizontally the picture to fit a 16 9 image into cinemascope screen This setting is to be used with an anamorphic installation where the lens is permanently fixed in front of the unit and to watch 16 9 content in its original format 16 9 SOURCE WITH ANAMORPHIC LENS o g o o o SDTV 16 9 Off o o o 8 o HDTV 16 9 Off Anamorphic Mode B NB When a 3D signal is fed the Anamorphic mode is reset to Off 9 7 Screen Adjust This setting corrects the color balance derived from the reflective characteristics of the screen without altering the global picture settings You may select Yunzi 1 only Off no modification Mode A slightly reddish Mode B slightly greenish Mode C slightly bluish Yunzi 2 amp 3 001 009 select a profile between 001 and 009 when watching 3D content with 3D shutter glasses Profile 001 is recommended when using Dreamvision s active IR 3D glasses 010 to 105 select the best compensation profile depending on your s
47. ion lamp directly by opening the cabinet while the illumination lamp is turned on The illumination lamp also contains ultraviolet rays and the light is so powerful that your eyesight can be impaired Do not drop hit or damage the light source lamp lamp unit in any way It may cause the light source lamp to break and lead to injuries Do not use a damaged light source lamp If the light source lamp is broken ask your dealer to repair it Fragments from a broken light source lamp may cause injuries The light source lamp used in this projector is a R699820 Yunzi Series User Manual 1 3 1 0 SAFETY INSTRUCTIONS high pressure mercury lamp Be careful when disposing of the light source lamp If anything is unclear please consult your dealer Do not ceiling mount the projector to a place which tends to vibrate otherwise the attaching fixture of the projector could be broken by the vibration possibly causing it to fall or overturn which could lead to personal injury Use only the accessory cord designed for this product to prevent shock The power supply voltage rating of this product is AC120 V AC100 V AC240 V the power cord attached conforms to the following power supply voltage Use only the power cord designated by our dealer to ensure Safety and EMC When it is used by other power supply voltage power cable must be changed Ensure that the power cable used for the projector is the correct type for the AC o
48. le HDMI 1 4a inputs The 3D effect is based on the binocular parallax which is the difference of the view on a single object when seen from the left and right eyes respectively Binocular parallax 3D movies use two sets of images one set for the left eye the other set for the right eye These images can be stored into three compatible formats Frame packing Top 8 Bottom or Side by Side This unit is compatible with the following 3D formats 1080p 23 98 24Hz Frame Packing Top amp Bottom and Side by Side 720p 50 or 59 94 60Hz Frame Packing Top A Bottom and Side by Side 1080i 50 60Hz Frame Packing and Side by Side 1080p 50 60Hz Side by Side The left and right images are produced alternatively Therefore the shutter glasses are used to separate the left eye images which will be only visible to the left eye and the right eye images only visible to the right eye The human brain then perceives stereo objects based on the visual differences between two images of the same object but taken from different angles The 3D glasses are used to separate the left and right image therefore producing a 3D effect 2 2 THX 3D Display Certification Yunzi 2 amp 3 The THX 3D Display certification aim to reproduce faithfully images at home according to the intentions of the film director during playback of 2D and 3D images and they are the proof H of high definition and high quali
49. lected color within smaller steps H settings 31 31 V settings 31 31 Reset Reset all pixel adjustments to default factory settings SHORTCUTS DURING PIXEL ADJUSTMENT GAMMA button on the RCU switches adjust color parameter between Red and Blue PIC ADJ button on the RCU switches the adjust area parameter between whole and zone At the same time the zone cursor will appear on the adjust pattern COLOR SPACE button on the RCU changes the adjust pattern from white to green adjust color Use the COLOR TEMP button on the remote control to change adjustment method from Pixel to Fine tune and switch to the fine tune window BACK button will exit the Pixel Adjust mode 9 3 Installation Style Flip the image to the left or right up or down according to the projection state of the projector Front Ceiling Mount F Rear or Rear Ceiling mount R 9 4 Keystone Compensate for trapezoidal distortion caused by installation Independently to the screen orientation make sure that the projector is not tilt more than 5 left right and 15 up down Vertical Keystone from 30 to 30 Horizontal Keystone from 40 to 40 NB When a 3D signal is fed the Keystone is inactive 32 699820 Yunzi Series User Manual 9 0 INSTALLATION SETTINGS 9 5 Pincushion Compensate distortions that may appear with curved screens or anamorphic setups from 20 to 20 NB When a 3D signal is fed the Pincushion correction is
50. nciple features an extremely high definition picture and seamless color gradations Emission Method LCoS Reflective Active Matrix Principle Display Panel Size 0 7 LCoS panels Native Resolution 3x 1920 x 1080 pixels Contrast Ratio 50 000 1 90 000 1 130 000 1 Projection Lens Throw Ratio 1 4 1 2 8 1 with 2 0x Zoom Electronic zoom focus and shift Electronic aperture control 16 steps Aperture Brightness 1200 ANSI Lumens Screen Size 60 to 250 Aspect ratio 16 9 Distance range from 1 50m to 12 m Input Signals Component Input 3x RCA VGA Yunzi 2 amp 3 D sub 3 lines 15 pins HDMI 1 Input version 1 4a with HDCP and CEC HDMI 2 Input version 1 4a with HDCP and CEC Color Management Advanced color settings 7 axis primaries secondaries and orange Video processing MPC with Detail Enhancement Blur DNR MNR BNR 2x FullHD frames per picture and advanced 1 16 pixel alignment Input Sync Frequency Analog Inputs 74 5 Mhz Digital Inputs 150 Mhz Light source Lamp 230W NSH lamp Power Requirements AC 110 V 240 V AC 50 Hz 60 Hz Power Consumption lt 360W 0 4W in standby mode Dimensions Width x Height x Depth 455x 215 x 505 mm 17 9 x 8 5 x 19 9 Excluding feet Net Weight 15 1Kg 15 4 Kg 15 4Kg 33 3 Ibs 34 Ibs 34 Ibs Gross Weight 24Kg 53 Ibs O
51. nd Blue Accurate color temperature may require professional tools such as dedicated software and colormeter Wait at least 15 minutes after startup before modifying the picture settings Xenon Modes are exclusive to Yunzi 2 amp 3 models Gamma 26 Gamma is the relationship between the color values of the data and the color values displayed The Gamma coefficient makes it possible to adjust the brightness of the midtones only without affecting the very bright and very dark areas If gamma is set too high middle tones appear too dark If it s set too low middle tones appear too light Depending on the current active Picture mode the Gamma setting can be set to Normal Standard setting for 2D Gamma A focus on tone Gamma B for film and movie projection S curve Gamma C for film and movie projection with more detailed blacks than setting Gamma D this setting is recommended for bright midtones and Computer like projection Gamma E Recommended setting for 3D movies Gamma Brighter picture than Gamma E Gamma G Recommended setting for HDTV and sport programs Gamma H Brighter picture than Gamma G Customi Custom2 Custom3 The Custom data can be set to Correction Value a unique value that will act as a gamma coefficient between 1 8 and 2 6 Gamma Adjustment the gamma curve can be adjusted for each color Red Green and Blue Copy copy the adjusted values to temporal memory
52. niques are necessary Be sure to ask your dealer or specialist to perform mounting Do not mount at places that may be subjected to vibration and shock Depth of the screw holes A is 23 mm Use at least 13mm long Screws but not longer than 23mm as you may damage inside the projector Install at a safe place in case this unit or a part of it may drop If the light source lamp is broken small pieces of glass from the mesh of the filter may appear outside the unit Regardless whether the unit is still under guarantee Dreamvision is not liable for any product damage caused by mounting the unit with third party ceiling mount or when the environment is not suitable for ceiling mount Dimensions Distances between left and right holes is D 337 mm Distances between front and back holes is d 290 mm 2 9 Projection Distance R699820 Yunzi Series User Manual I 2 0 INSTALLATION GUIDELINES Projection Distance Chart Yunzi Series Projection Screen Projection Screen Projection Screen Size Size Height Diagonal size Base size Aspect Ratio 16 9 Aspect Ratio 16 9 Aspect Ratio 16 9 Projecting Distance minimum maximum 50 1270 mm 43 6 1107 mm 24 5 623 mm 151 cm 305 cm 60 1524 mm 70 1778 mm 52 3 1328 mm 29 4 747 mm 178 cm 366 cm 61 0 1550 mm 34 3 872 mm 209 cm 428 cm 83 2108 mm 92 2337 mm 72 3 1837 mm 40 7 1034 mm
53. o not use this unit in rooms with cigarette smoke or oily smoke This may cause the unit to malfunction Check temperature during install If there is a heater the air may reach a higher temperature than expected Precautions of Usage This unit makes use of a light source lamp that reaches a high temperature during projection Do not allow projection under the following conditions Projection with the unit laid on sides Projection at a location that blocks the air inlets or exhaust vents Projection at a place exposed to air blasts from an air conditioner Allowed Inclination during operation Due to the lamp position and operating angle this unit cannot operate with more than 5 angle horizontally and 15 angle vertically This unit cannot be operated on the side ap 2 7 Air Flow and Space Requirements This unit can be installed in table ceiling rear table or rear ceiling position Make sure that the unit is installed within the space requirements described below A air inlets B air outlets 10 R699820 Yunzi Series User Manual 2 0 INSTALLATION GUIDELINES 150 mm 200 mm Space reguirements 2 8 Ceiling Mounting the Unit When mounting of this unit is required make use of the 4 screw holes M5x20 screws at the bottom of this unit indicated by the letter A Allow sufficient space around the air inlets to avoid blocking them Precautions for Ceiling mount To ceiling mount this unit special expertise and tech
54. on or Control device eee 20 MENU STRUCTURE sismici 21 PICTURE ADJUST SETTINGS canalina 25 74 Picture Mod s and Color Pfofiles esa alal iaia 25 1 2 Color Temperature ctore iii 26 7 3 Gamma aaa veh 26 7 4 Dark Bright 27 7 5 Picture Tone BD Ur VR GERI 27 7 6 CONtrast ga alii 27 7 7 Br 27 7 8 len 27 7 9 TR 27 TAQ Advanced Picture ERE nni 27 7 1 Reset Picture Profile collera Ur red T RIS D UR oO ae 28 INPUT SIGNALSETTINGS DE a Dr 29 8 1 HDMI Serene recreo eye E AFRICA 29 8 2 COMPONEN c EIE ES 29 8 3 Yunzi 2 amp 3 only 2i etoitim ine as ain ne epe 29 8 4 Tera ecyuTo lE PH 29 8 5 Duos M u 29 8 6 30 8 7 Progressive only 4801 5761 10801 set eee inertio E E ees 30 8 8 n 30 8 9 Expert Calibration Yunzi 2 83 panini aen wee oe eae p HER pe HE ert 31 INSTALLATION SETTINGS iaia 31 9 1 Lens COMM Me 31 R699820 Yunzi Series User Manual 9 2 US ale
55. on to cords at doors plugs receptacles and the point where they exit from the product For added protection of this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the cable system This will prevent damage to the product due to lightning and power line surges Do not overload wall outlets extension cords or convenience receptacles on other equipment as this can result in a risk of fire or electric shock Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages and other hazards Refer all service to qualified service personnel 1 0 SAFETY INSTRUCTIONS Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen on the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the Operation Manual as an improper adjustment of controls may result in damage and
56. orange prepare to replace the lamp before 4000 hours The lamp failed to ignite restart the projector after a complete cooldown cycle Lamp has shut down during projection blinking continuous 2 times restart the projector after a complete orange red cooldown cycle Lamp cover is open Check that the lamp 3 times cover is firmly closed and restart the projector Power Supply failed Cooling fans stop blinking Internal thermal sensor detects orange 3 times overheating External thermal sensor detects 4 times overheating 1 time Startup or drive circuits failed blinking 2 times Communication with drive circuit failed orange blinking red 3 times Scaler circuit failed 4 times Electrical lens cover failure ABOUT WARNINGS AND CooL DowN MODE After projection or when a warning occurred cases 7 16 the unit will go through a 1 minute cool down process known as the Cool Down mode This function is to prevent lamp breakage and shortened lamp life but also damage to the internal components of the projector The Cool Down mode is indicated by the blinking red STANDBY ON led When in Cool Down mode the projector cannot be turned ON After the Cool Down process is completed the unit will automatically switch to the Standby mode indicated by a red STANDBY ON led CAUTION When in Cool Down mode do not pull out the plug from the outlet Also do not block the air inlets exhaust
57. peration Environment Temperature 5 C to 35 C Storage Temperature 10 C to 60 C Humidity 20 to 80 without condensation Design and specifications are subject to change without prior notice Please note that some of the pictures and illustrations may have been abridged enlarged or contextualized in order to aid comprehension Images may differ from the actual product 3 CHIP LCoS SYSTEM LCoS is the abbreviation of Liquid Crystal on Silicon The 3 Chip LCoS systems feature dedicated panels for each color channel and render seamless color graduations without any flickering or rainbow effect artifacts R699820 Yunzi Series User Manual 15 0 MISCELLANEOUS Dimensions R699820 Yunzi Series User Manual 49 15 0 MISCELLANEOUS HOW TO REPLACE BATTERIES ON INFRA RED 3D GLASSES PULL OUT RADIO FREQUENCY 3D GLASSES Insert the Paper clip into the hole in the right side of glasses until you hear the click STEP Pull towards you with your nail to remove the battery tray STEPO Reinsert the battery and push to hear the click to lock it Radio Frequency 3D Glasses uses rechargeable batteries that can be recharge using the mini USB connector 50 R699820 Yunzi Series User Manual 15 0 MISCELLANEOUS R699820 Yunzi Series User Manual sS _ f ream Jision WE MAKE THE WORLD DREAM Yunzi Series R699820
58. r physical condition should not watch 3D stereoscopic images It is also recommended that you take a break periodically Prevent child under 5 years old to watch 3D The comprehensive brain function to judge stereoscopic vision which includes the feeling for real distances develops while growing up by touching and seeing real objects but in early childhood it is still in an underdeveloped state Even though there are individual differences children under 5 are still developing Letting them frequently watch virtual 3D video images can be an obstacle for the development of a comprehensive three dimensional feel Additionally younger children may suddenly become sick because they continue watching without realizing symptoms like 3D sickness or deterioration of health Please accompany your child while it watches 3D programs 2 4 3D Synchro Emitter and 3D Glasses In order to match the timing of the displayed video images with the timing of the opening closing 3D glasses shutters for each eye the projector in 3D mode sends the correct synchro data to the 3D synchro emitter INFRARED SYNCHRONIZATION In regard to the Infrared 3D emitter if you experience synchro issues with Infra Red glasses in an installation where the synchro signal is bouncing from the projection screen please direct the 3D emitter in such a way towards the seats that the infrared rays can directly reach the 3D glasses In a few cases the synchronization may not work correctly
59. rap Operating buttons Main Power Air Inlet Input Panel connect your video source to the correct input Operating and Navigation buttons described in section 4 4 page 18 Main Power connect the power cord as shown below Lamp trap see Procedure for Lamp Replacement page 38 for more details about lamp replacement Air Inlets see Air Flow and Space Requirements page 10 16 LLL 699820 Yunzi Series User Manual 4 0 GETTING STARTED 4 2 Connecting the Power Cord Before plugging in the Power Cord ensure that all devices have been connected to their respective inputs to this unit Connect the power cord to the power input terminal of the projector CAUTION AGAINST FIRE AND ELECTRIC SHOCK Since the power consumption of this unit is high insert the power plug directly into a wall outlet Do not use a power voltage different from that which is indicated Do not cut tear or modify the power cords Also do not place a heavy object on heat or stretch the power cords as this may cause damage to the cords 4 3 Operating LEDs WARNING orange red LED LAMP orange LED Bb STANDBY ON 9 6 Emm green red LED Operating LED ID STANDBY ON LAMP WARNING Description green or red orange orange red 1 red Unit is in standby mode 2 green Unit is in operate mode during projection Unit is in operate mode but HIDE is ON
60. rea of the picture Phase Adjust flickering and blurred pictures Picture Position Adjust the display position of the picture 8 4 Picture Position Depending on your source you may find that the picture should be adjusted into the screen adjust the horizontal and vertical position of the picture into the screen Some signals may not be fully displayed adjust this setting properly when necessary 8 5 Aspect Ratio When watching a movie or video program you can manually set the desired aspect ratio to fill your screen Select R699820 Yunzi Series User Manual 29 8 0 INPUT SIGNAL SETTINGS the correct aspect ratio depending on your source For Video sources a 4 3 The original source is considered as 4 3 format Generally SDTV broadcasts b 16 9 The picture size is 16 9 generally most recent DVDs Blu Ray discs or HDTV broadcasts c Zoom The zoom function is useful to zoom in the picture and eliminate black bars When watching 3D content only 16 9 aspect ratio is available For PC sources a Auto Zoom the picture to fill either the screen height or the screen base which ever happens first b 1 1 mode pixel to pixel mapping no scaling c Full Stretch the picture full screen 8 6 Mask Depending on your source you may enable or disable this feature to hide the outer area of the picture The Mask function can hide the unexpected scaling artefacts found in broadcast program You can set it to Off 2 5 or
61. rtable with the 3D effect In general women and children have smaller faces and may feel better with a smaller parallax value Do not hesitate to alter this settings if you feel eye strains or headaches The correct Parallax value also depends on your projection screen size Due to the large screens used in home theaters compared to flat screen TVs we recommend a negative value of 6 for computer sources and video games in native 3D with large parallax This setting is best at O for Blu Ray movies aimed for Digital Cinema audience Crosstalk Cancel Can be adjust with a 3D signal input but not when 2D to 3D Conversion is On This function is to lessen the residual cross talk found between 3D video images Adjust the Parallax value and then the Cross talk settings in order to cancel the residual cross talk without loosing picture quality Adjustments White Red Green and Blue 8 8 Negative values reduce visible Crosstalk positive values bring a brighter 3D picture at the cost of more Crosstalk R699820 Yunzi Series User Manual 9 0 INSTALLATION SETTINGS Intensity 2D to 3D Conversion is On Because the 2D to 3D Conversion may not detect the correct depth of the picture elements you can use this function to enhance the depth perception during the conversion Adjust setting from 1 up to 5 Subtitle Adjust 2D to 3D Conversion is On Use this function to automatically identify subtitles during 2D to 3D conversion There may be ins
62. s average lamp is not guaranteed and may not reach 4000 hours depending on the operating conditions Deterioration progresses rapidly when the remaining lamp usage time is short Get ready or replace with a new lamp when the accumulated usage time exceeds 4000 hours Depending on the operating conditions the lamp may have to be exchanged earlier If the image is dark or if the color tone is abnormal replace the lamp as soon as possible You can also check the accumulated hours of usage Please refer to Lamp Time in the Information menu When the lamp usage time exceeds 2900 hours The Lamp replacement message will be displayed on the screen the next three projection starts Press the BACK button to clear the display ABOUT LAMP REPLACEMENT If this unit is installed in a constricted place attempting to replace the lamp in that place may cause injury Move this unit to a place large enough to perform work Use only genuine replacement parts for the lamp unit Otherwise malfunction may occur Also never attempt to re use an old lamp unit This may cause marked performance deterioration or lamp blowout thus leading to unit malfunction Broken pieces of the lamp outside this unit may also cause injuries during lamp unit exchange Do not replace the lamp immediately after this unit has been used The temperature of the lamp is still high and this may cause a burn Allow a cooling period of 1 hour or more before replacement Before repl
63. t is used on a cart care should be taken to avoid quick stops excessive force and uneven surfaces which may cause the product and cart to overturn damaging equipment or causing possible injury to the operator Slots and openings in the cabinet are provided for ventilation These ensure reliable operation of the product and protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the product on bed sofa rug or similar surface It should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided the manufacturer s instructions have been adhered to For proper ventilation separate the product from other equipment which prevent ventilation and keep a distance of more than 5 9 150 mm This product should be operated only with the type of power source indicated on the label If you are not sure of the type of power supply to your home consult your product dealer or local power company This product is equipped with a three wire plug This plug will fit only into a grounded power outlet If you are unable to insert the plug into the outlet contact your electrician to install the proper outlet Do not defeat the safety purpose of the grounded plug Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attenti
64. tances where automatic identification does not work or video images are accidentally identified as subtitles and therefore not converted into 3D Set if On or Off 8 9 Expert Calibration Yunzi 2 amp 3 Expert Calibration is accessed only by using a programmable IR RCU RS 232C or LAN control Two additional sets of Picture Modes can be activated Each set designated as THX and ISF profiles have to be calibrated Once done these profiles are stored and displayed in the picture mode menu list but will not be modifiable Additionally the Calibrator can certify his action by setting in the Information Menu his name or company name See RS 232C protocol page 40 for more details 9 0 INSTALLATION SETTINGS 9 1 Lens Control This menu gives access to the control of the lens Browse into this menu for the following adjustments Focus Adjust the lens focus to obtain a clear picture Zoom Adjust the lens zoom to fill the screen with the picture Shift Adjust lens shift to center the picture into the screen Image Pattern If set to On an internal pattern will be generated to adjust the current setting If you want to use an external generator turn this option to Off Lock Once the Lens is correctly set you may lock this setting menu by turning the Lens control Lock to On Any attempt to access the Lens control menu will lead to the display of a warning message Lens Memory Select Call up saved lens adjustment data to
65. ter than E F recommended for sports G brighter than G H Custom1 Custom2 Custom3 Dark Bright Level Dark Level White 7 7 Dark Level Red 7 7 Dark Level Green 7 7 Dark Level Blue 7 7 Bright Level White 7 7 Bright Level Red 7 7 Bright Level Green 7 7 Bright Level Blue 7 7 Picture Tone White 16 16 Red 16 16 Green 16 16 Blue 16 16 Contrast 50 50 Brightness 50 50 Color 50 50 Tint reddish to greenish 50 50 Advanced MPC Level 4K Profile Film High Resolution HD SD Dynamic Off Enhancement 0 100 Dynamic Contrast 0 100 Smoothing 0 100 Noise Reduction RNR 0 16 MNR SD only 0 16 BNR SD only On Off Custom Gamma Custom1 Custom2 Custom3 Correction value Gamma Adjustment White Red Green Blue Color Management Off Custom1 Custom2 Custom3 Pause On Off R699820 Yunzi Series User Manual Picture Adjust 6 0 MENU STRUCTURE Advanced Color Management Color Axis Position 30 30 Hue 30 30 Saturation 30 30 Brightness 30 30 User Name Edit User1 User5 edit name 10 char max Clear Motion Drive Off Low High Inverse Telecine Lens Aperture 15 0 Lamp Power Low High Reset Profile Confirm Input Signal HDMI Input levels 16 235 Standard 0 255 Enhanced 16 255 Super White Level Check displays pattern Color Space Auto YCbCr 4 4 4 YCbCr 4 2 2 RGB Control with HDMI CEC On Off COMP Color Space YCbCr RGB PC input Yunzi 2 amp
66. the Lens Control menu press the Ok button to access the Zoom adjustment Use the up and down buttons to adjust the picture size until the screen is completely filled 2 10 0 3 Adjust the Picture Focus From the Lens Control menu press the Ok button to access the Focus adjustment Use the up and down buttons to adjust the picture focus Using Lens Memories You can save the current picture position zoom and focus in up to 5 different Lens Memories 10 for Yunzi 2 amp 3 Each memory stores the current position zoom focus of the lens and you can also set a custom name of 10 characters or less Saving current lens setup Fist step is to set the lens to fill the desired screen Then go into the Menu Installation Lens Control Select Lens Memory Save and choose a free slot available You can call back anytime later this current lens setup using the direct access button Lens Mem ory on the RCU Limitations of use Each memory can store a different picture size and position but there are limitations on the possible pictures sizes and positions because of the projector being at a fixed location In order to calculate the best position of the projector toward the screen the installer has to make sure that among the different desired pictures the smaller one with the smaller zoom is within the offset limits horizontal and vertical shifts of the projector Once the position of the projector is determined by the smallest possible pi
67. tion THX dark ISF Day ISF Night Color Profiles Yunzi 1 HDTV Standard the list varies upon current Picture Movies and films Film Mode Digital Cinema standard Cinema Animations Anime TV sports Natural Live concerts Stage 3D contents 3D Color Profiles Yunzi 2 amp 3 Eastman Kodak movies Film1 the list varies upon current Picture Fujifilm movies Film2 Mode Technicolor movies Film3 HDTV Standard Movies 1 Digital Cinema standard Cinema2 Animations Anime1 Richer colors than Anime1 Anime2 TV sports Video Games Vivid Computer inputs AdobeRGB Live concerts Stage THX THX 3D movies 3D Cinema 3D TV programs sports 3D Video reguire individual adjustment and or calibration Custom 1 5 Off Color Temp Preset value 5500K 6000K 6500K 7000K 7500K 8000K 8500K 9000K 9500K High brightness Xenon Modes Yunzi 2 8 3 R699820 Yunzi Series User Manual Film projector Xenon1 DCI projector Xenon2 Cooler tones than DCI Xenon3 Custom1 Gain Offset Custom2 Gain Offset Custom3 Gain Offset 21 6 0 MENU STRUCTURE 22 Picture Adjust Gamma If Picture mode is Film Eastman Film1 Fujifilm Film2 more tone than Film1 Film3 more contrast than Film2 Film4 If Picture mode is not Film focus on tone A film S curve B more contrast than B C bright and PC like picture D recommended for 3D E brigh
68. ty indicating that Yunzi 2 amp 3 have cleared more than 400 rigorous image quality tests D S P L A Y including accuracy of color reproduction cross talk viewing angle and video processing performance 8 a 699820 Yunzi Series User Manual 2 0 INSTALLATION GUIDELINES The THX certification features by using THX picture mode Correct Gamma and Color Temperature No Overscan or Scaling Correct High Definition color Gamut The Best in Class Parameters also include ANSI and Sequential contrast luminance and color Uniformity color tracking with gray scale optimum brightness deinterlacing performance jaggie and countouring 2 3 Comfort and Caution with 3D Content The closer one looks at stereoscopic images the greater the binocular disparity which means greater perception of outward projection At the same time the spectator must focus on these outward objects on the screen The projecting image and the real focus distance cause a great contradiction This causes visual fatigue and discomfort That means that the more 3D effect the more outward effects and the more your eyes will try to focus nearer than where the objects are actually really located This strain contributes to fatigue and discomfort CAUTION ABOUT HEADACHES AND EYE STRAINS Please stop watching if you do not feel well and consult a physician if necessary People who already have a kind of photosensitivity sufferers from heart disease and people in poo
69. utlet in your country Consult your product dealer Caution Do not allow any unqualified person to install the unit Be sure to ask your dealer to install the unit e g attaching it to the ceiling since special technical knowledge and skills are required for installation If installation is performed by an unqualified person it may cause personal injury or electrical shock Regional Specific Information R699820 Yunzi Series User Manual CE mark and Directive 2011 65 EU ROHS 2 Europe only In accordance with Article 7 and the adoption into national law by 2nd January 2013 this product has been designed and manufactured in accordance with Article 4 The technical documentation and the written declaration of conformity that assesses the product conformity can be provided to the competent National Authority upon an email request to rohs2 dreamvision net FCC Information USA only Changes or modification not approved by Dreamvision could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications
70. vents by standing the projector on its end or laying it on its side 15 0MISCELLANEOUS 15 1 RS 232C protocol Serial communication specifications Control of this unit is possible using a computer or automation device connected with a RS 232 cross cable female female D sub 9 pins cable or LAN RJ 45 cable Communication specifications for this unit are as follows 40 R699820 Yunzi Series User Manual 15 0 MISCELLANEOUS Baud Rate 19200 bps Data Format Binary Mode Asynchronous Character Length 8 bits Parity None Start Bit 1 bit set to high Stop Bit 1 bit set to low X on off None Flow Control None RS 232C pin assignation 000000 00000 Command Format Pin Signal Function Signal Direction 2 RxD receive data PC gt Projector 3 TxD transmit data Projector gt PC 5 GND ground 1 4 6 9 N C When sending a command to this unit use the following data format eader nit omman ata 1 byte 89h 01h 2 bytes at least 1 byte 0Ah Header 21h Operating command PC gt Projector SFh Reference command PC gt Projector 40h Response command Projector gt PC 06h ACK Projector gt PC Unit ID Fixed to 89 h 01h Command 2 bytes See the list of the available commands below If Command code is 52h 43h the Data sent may also be sent to the
71. witch to Inverse Telecine CEC switch to ON 37h 33h 35h 37h CEC switch to OFF Aspect Ratio 52h 43h 37h 33h 37h 37h Toggle Aspect Ratio 37h 33h 32h 35h 37h 33h 32h 36h 37h 33h 32h 37h 37h 33h 41h 45h Set Aspect Ratio to 4 3 Set Aspect Ratio to 16 9 Set Aspect Ratio to Zoom PC Auto 37h 33h 42h 30h PC Full 37h 33h 41h 46h PC Just Anamorphic Modes 52h 43h 37h 33h 32h 34h 37h 33h 32h 33h 37h 33h 32h 42h 37h 33h 43h 35h Turn OFF the Anamorphic mode Anamorphic set to Mode A Anamorphic set to Mode B Cycle Anamorphic Mode through OFF A B 3D Modes 2D 3D Conversion 52h 43h 52h 43h 37h 33h 44h 42h 3D Mode set to Auto 37h 33h 44h 43h 3D Mode set to Side by Side 37h 33h 44h 44h 37h 33h 44h 45h 37h 33h 45h 32h 37h 33h 45h 33h 3D Mode set to Top amp Bottom 3D Mode is disable force 2D 2D to 3D conversion is OFF 2D to 3D conversion is ON 3D Left Right Phase 49h 53h 33h 50h 30h standard phase Left Right 33h 50h 31h inverse phase Right Left 3D Subtitle Correction 3D Parallax 3D Parallax 49h 53h 49h 53h 4Ch 56h 49h 53h 4Ch 56h 33h 54h 30h 33h 54h 31h 46h 46h 46h 31h Subtitle correction is OFF Subtitle correction is ON Set 3D Parallax to 15 46h 46h 46h 38h Set 3D Parallax to 8 46h 46h 46h 39h Set 3D Parallax to 7 46h 46h 46h 41h 46h 46h 46h 45h 46h 46h 46h 46h Set 3
72. y deteriorate and lamp blowout may occur 14 4 Cleaning and Replacing the Dust Filters The filters must be cleaned regularly to allow an efficient air intake Otherwise dirt may enter the unit and appear on the screen preventing you from enjoying the video fully If dirt has entered the unit or if you need information about the filter please consult your authorized dealer A filter cleaning warning appears every 500 hours Cleaning procedure Pull out the power plug from the outlet while the projector is in standby mode Push up and lift the claw of the filters pull out the filters Clean the filters with water and dry them avoiding direct sunlight In extremely soiled cases use of a neutral detergent is recommended Insert the filters in their original positions and make sure that the claws are firmly inserted 14 5 Troubleshooting Operating LED ID STANDBY LAMP WARNING gii Description ON orange LED red LED 9 1 red Unit is in standby mode 2 green Unit is in operate mode during projection biini in Unit is in operate mode but HIDE is ON 3 9 Yes Press again on HIDE button to obtain a green picture 4 blinking red Yes Unit is in cooldown mode switching off R699820 Yunzi Series User Manual 39 15 0 MISCELLANEOUS Operating LED STANDBY LAMP WARNING Description ON orange LED red LED 9 Lamp time has reached 2900 hours and or

Yunzi - User Manual v2.1

Contents

Download Pdf Manuals

Related Search

Related Contents