Table of the Contents ALM-SPD20
Contents
1. video video RS485 alarm output Aaa a alarm input power HE ideas ESE ESIC 654521 E Es i i Jack for Heater A EAN AE amplified figure 5 4 4 Switching on Power a Make sure the polarity of plugs sockets and cables connection is correct then switch on power b The High speed Dome Camera begins to do the self check by moving pan 360 tilt 90 to check the camera lens the electrical and mechanical structures in pan tilt state then executing the restoration program and resuming its original position After the High speed Dome Camera stops moving it finishes self check and is ready to receive controlling instructions c Use controlling device to control the High speed Dome Camera checking whether it can perform the functions of the pan tilt and camera lens If not please check the setup of communication protocol Baud rate and address and the connection of 485 controlling cable 25 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 5 4 5 Vitreous Cover Installation a Clean the dust and stain on the vitreous cover with soft cloth attention not to scrape the vitreous cover b Aim the four special bolts the bolts don t fall even if they are loosened to the extreme in the vitreous cover at the bolts holes in the outer housing then tighten the bolts 5 5 Installation of Pendant mount High Speed Dome 5 5 1 Insta2. Focus Control The system takes auto focus as the default While moving the camera can automatically focus on the center of the object view to get clear image Under special circumstances the user can manually adjust the focus to achieve desired image effect e Manual focus can be realized through controlling the keyboard or matrix For details please refer to the operation manual of the controlling keyboard 3 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br or matrix e In the state of manual focus the user can control focal length to make the lens focus on the object If the High speed Dome Camera is set up to resume auto focus upon joystick operation when there is operating on the joystick the High speed Dome Camera will automatically focus If a period of time is set up for auto focus resuming once there is no controlling order received after the period of time the High speed Dome Camera will resume auto focus Under the following circumstances the camera can not carry out auto focus e When the object is not in the center of the view e When simultaneously observe a far object and a near one clarity for both of the images can not be guaranteed at the same time e When observing objects with extreme brightness such as neon lights spotlight etc e When the object is behind the glass with water drops or dust e When the object moves very
3. minutes the high speed dome camera will automatically turn to the default position and monitor 1 Setup the Default Position Move the High speed Dome Camera to a key monitoring area through controlling keyboard then enter number 164 124 from the keyboard and press the PREVIEW key then the setup is successful 2 Activate and Exit the Default Position function The user can activate or exit the function of default position through the keyboard Enter number 162 122 and press the PREVIEW key the function is activated Enter number 163 123 and press the PREVIEW key the function is exited 6 10 Open and close fog dispersion function Due to the influence of the climatic condition there may be fog on the vitreous cover of the high speed dome if it influences the image of the camera the user can disperse the fog through the Fog dispersion function 46 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br so that the user can see clear image Working principle When the fog dispersion function is open the heater and the fan will begin to work simutaneously the temperature inside the speed dome will increase thus the fog will disappear The operation is as below 1 Open the fog dispersion function a Input 165 125 b Press PREVIEW key 2 Close the fog dispersion function a Input 166 126 b Press PREVIEW
4. oo a0 cromo z ooon ooo a oomoo so oro um ooo ss onon se oono Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 00011011 00011100 00011101 00011110 00011111 62 00111110 01011101 a os aS 87654321 ME 87654321 125 10011100 10011101 10011110 room im 10100000 10100001 10100010 10100011 10100100 10100101 10100110 10100111 10101000 10101001 10101010 10101011 10101100 10101101 10101110 144 14 14 58 00111010 01011001 E 59 oo111011 90 oomoo 92 93 ms 8 27 onon como como omo st oom ms 94 95 97 111 00111100 01011011 61 00111101 01011100 a fsa lalala lala la lalala gt lo lo lo lo lo jo jo lo yo so O j jo IN loja j lolnlIialo ortrooor 1a soro 115 toon 10110000 10110001 a fafa fa ajA jo n Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br E E 233 211 234 mooo 235 1101011 236 11101100 237 monto 238 mono 239 mon 194 11110000 ss TT 196 momo 29 nonon 2 moo 50 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 51
5. screw slot of the installing port of the housing 5 5 3 Connection of Exterior Cables Connect BNC video outlet of the High speed Dome Camera with the already disposed video cable the power cable with the already disposed power cable AC24V or DC14V and RS485 controlling cable with already disposed RS485 controlling cable The cables of high speed dome camera is shown below 27 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Power cable AC24V or DC14V high speed dome Power supply connecting outlet power supply power supply adaptor 485 cable 485 controlling high speed dome Green A white B signal controlling device Video Cable Camera signal Camera BNC connector monitoring device 5 strand Alarm input Detctor Black Alarm input public terminal cable high speed dome Yellow the 1st channel alarm input Green the 2 channel alarm input Blue the 3 channel alarm input White the 4th channel alarm input 2 strand Alarm output High speed dome Brown alarm output public terminal cable alarm horn Grey alarm output terminal Make sure the polarity of RS485 controlling cable connection is correct A RS485 positive B RS485 negative 4 If wrongly connected the High speed Dome Camera will be out of control 5 5 4 Switch on Power a Make sure the polarity of plugs sockets and cables connection is corr
6. weight of the High speed Dome Camera A Use the ceiling mount installation board as template and draw the positions of the three installing holes and the cable hole on the desired ceiling locus B Use an electric drill to make three Expansion screw holes for M6 screws on the above drawn positions and drive in the Expansion M6 screws C Use an electric drill to make a cable hole with the diameter of 20mm on the ceiling 29 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br D Push the power cable communication cable and video cable through the cable hole leaving long enough cables for connection E Fix the ceiling mount installation board firmly on the ceiling with three M6 screw nuts and washers Ceiling mount Installation Board oq x x Raso XXX OS 2 ese zy Z Dea CXEXEEEA DOORS OO epi LELES 2505 POO 10 XX SO SA o So Vas KRY Z 220 EXER OOo OS 220 Cable Hole in the Ceiling Y 3 9 7 5 120 evenly distributed Ceiling 5 6 2 Installation of High Speed Dome Camera A Unpack the carton and carefully take out the High speed Dome Camera and its attachments open the vitreous cover and take out the fillings B Check cable connectors and see if any of them loose and set up the coding switch C Install the module of
7. auto manual AGC Auto System of signal NTSC PAL S N gt 48dB Signal output 1 0 0 2Vpp 2 6 Camera Module Data Built in CNB Camera Module Type CNB 22x Color day and night Synchronization Internal sync external sync Scan 2 1 interlace Resolution 480TVL Min illumination 1 0Lux Color 0 01Lux Black and White Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br AGC Auto System of signal NTSC PAL S N gt 50dB Video Signal output 1 0 0 2Vpp lil Characteristics Adopting multi functional high performance DSP design with stable performance Integrated design with compact structure and high reliability 4 Precise electric motor drive ensuring smooth running and agile reaction 4 The internally saved data will not lose within a short period of time 1 year since power off in built module programme which can automatically identify 5 brands of cameras including LG SONY HITACHI CANON CNB Other camera programmes can also be added as per the requirement of the customers 4 128 preset positions for random storage and accurate locating 4 tour groups 16 preset positions can be included in each tour group Support Left amp Right scan and 360 scan function Low Medium and High 3 levels speeds optional 4 The unit has a default position 4 4 channels alarm in 1 channel alarm out 4 Pan 360 consecutive mo
8. close alarm function e For the input terminals which are not connected with detectors 2 2KO risistor must be connected otherwise the speed dome will thinks that there eee Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br is alarm signal coming in thus the alarm output is always on Alarm output connection sketch 1 channel alarm output o o Z o Connection sketch for Alarm input with Usual closed detector 2 2kresistor ALM 1 ALM 2 ALM S ALM 4 once ALM 1 activated No 1 preset position certain to be previewed once ALM 2 activated No 2 preset position certain to be previewed once ALM 3 activated No 3 preset position certain to be previewed once ALM 4 activated No 4 preset position certain to be previewed 1 No 1 2 3 4 preset position must be set well in advance so that the alam functions can response Connection sketch for Alarm input with Usual open detector 34 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br AL i ALM 2 ALM S ALM d E once ALM 1 activated No 1 preset position certain to be previewed once ALM 2 activated No 2 preset position certain to be previewed once ALM 3 activated No 3 preset position certain to be previewed once ALM 4 activated No 4 preset position certain to be previewed f No 1 2 3 4
9. corresponding positions Users can use such devices as controlling keyboard to save and preview preset positions quickly and conveniently The High speed Dome Camera can support 128 preset 40 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br positions 6 3 1 Set up Preset Positions After adjusting the pan tilt of the High speed Dome Camera to desired state including position lens focus and iris through the keyboard enter the number representing the preset position and LED displays the entered preset position number Press the PRESET key then LED resumes to previous displaying state again now you have set up the preset position successfully Example Set up preset position No 1 a Use the joystick to move the High speed Dome Camera to the desired position and adjust the camera lens b Enter 1 c Press the PRESET key Manual focus approach can be adopted to set up preset positions for distant objects that is after adusting the lens to focus on distant place control the keys FOCUS and FOCUS on the controlling keyboard to set up optimal focal image storage to avoid fuzzy images resulting from the interference of other distant objects 6 3 2 Preview Preset Positions The function enables the High speed Dome Camera to quickly return to the preset position Enter the number 1 128 key for preset position number w
10. in the tour enter the number 141 111 on the keyboard and press the PREVIEW key to exit the tour setup D Start Running a Tour In the keyboard initial state enter number 142 112 and press the PREVIEW key to start running the preset tour Example Set up the tour order to be 1 2 5 3 4 6 please set up preset positions before tour setup 1 Preview preset position 140 110 to enter tour setup Enter number 42 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 140 110 and press the PREVIEW key Preview preset position 1 to set up the first tour position Enter number 1 and press the PREVIEW key Preview preset position 2 to set up the second tour position Enter number 2 and press the PREVIEW key Preview preset position 5 to set up the third tour position Enter number 5 and press the PREVIEW key Preview preset position 3 to set up the fourth tour position Enter number 3 and press the PREVIEW key Preview preset position 4 to set up the fifth tour position Enter number 4 and press the PREVIEW key Preview preset position 6 to set up the sixth tour position Enter number 6 and press the PREVIEW key Preview preset position 141 111 to exit tour setup Enter number 141 111 and press the PREVIEW key Preview
11. interlace Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Illumination 0 7Lux 0 001Lux Focus auto manual Lens zoom ratio 18x optical zoom 12x electronic zoom Focal length 4 1 73 8mm Effective angle Wide 48 tele 2 7 Manual auto Auto System of signal NTSC PAL S N gt 50dB Signal output 1 0 0 2Vpp Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 2 4 Camera Module Data Built in HITACHI Camera Module Type HITACHI 23 color HITACHI 23 color day and night Synchronization Internal sync external sync Scan 2 1 interlace Resolution 480TVL for color 600TVL for B amp W Min Illumination 0 2Lux for color 0 02Lux for B amp W Iris auto manual Focus auto manual Lens zoom ratio 23xoptical zoom 10x electronic zoom Focal length 3 6 98mm Effective angle Wide 55 tele 2 4 BLC Manual auto White Balance Auto AGC Auto System of signal NTSC PAL S N gt 50dB Signal output 1 0 0 2Vpp 2 5 Camera Module Data Built in LG Camera Module Type LG 27x color LG 27x color day and night Synchronization Internal sync external sync Scan 2 1 interlace 8 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Resolution 480TVL Es Iris
12. joystick to trace and monitor if the user move the lens to the bottom vertical then continues pressing the joystick the lens will automatically flip 180 horizontally then the user can still control 11 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br it to move upwards till 90 which enables the user to directly observe the situation on the back side thus tilt 180 consecutive monitoring can be realized 4 Set up and Preview Preset Positions The preset position function works in this way the High speed Dome Camera stores the data of the pan tilt angles and lens focal length in current state when needed preview these data then move the pan tilt and the camera to the corresponding position The user can quickly and conveniently preview the preset position with the controlling keyboard The High speed Dome Camera supports 128 preset positions 5 Automatic Tours The automatic tour function is a built in function of the High speed dome camera Through beforehand programming the user can arrange the preset positions into the automatic tour in the desired order then the user can use such equipment as controlling keyboard to make the High speed dome camera automatically move as per the order of the preset positions set in the tour with stipulated time intervals e Automatic tour among preset positions can be realized through grouping together
13. key VII Trouble Shooting Table Problems Possible causes remedies action no Wrong connection of power cables Correct haem no indicator on when power is Power supply adaptor damaged switched on Bad power cable connection Normal self check Address or Baud rate setup wrong Set up again and image but out of control Protocol setup wrong RS485 bus bad connection Check RS485 bus connection check image with motor noise Power supply not enough Replace better to place the Unstable image Fuzzy image At Manual focus state Operate the High speed Dome Camera or preview any preset positions Some High speed Power supply not enough Replace better to place the Dome Camera out adaptor nearby the speed dome of control or control Whether matching resistor is in the Install matching resistor in the High speed Dome Camera at the High speed Dome Camera farthest end delayed Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br The distance is too far the Thicken the controlling cable attenuation of 485 signal is too much The driving power of the 485 Replace with converter with converter is not enough separate power suppl VIII Correspondence of Address and Coding Switches SW1 DIP1 DIP8 4 cmo ooon oroo 6 o0 a ooo ooo 7 com ooo ooo 8 o ww ooon vo oono gt
14. preset position must be set well in advance so that the alam functions can response 35 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br VI Setup of the functions of the High Speed Dome 6 1 Setup Address Baud Rate and Protocol for High Speed Dome Camera Before the installation of the High speed Dome Camera you must confirm the protocol and Baud rate of the controlling system as well as the address code of the high speed dome camera then set up the switches in the speed dome to conform to the controlling system The corresponding switches setup is shown in the following figure Protocol Switches 1 2 Baudrate Switches 3 4 a Address Switches 1 8 knmi a a a o er aa Amplified Picture 36 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 6 1 1 Set up Communication Protocol of the High Speed Dome Camera The DIP 1 and DIP 2 of SW2 on the PCB board is for communication protocol setup Please refer to the following table PROTOCOL PELCO_D JCO PELCO_D1 If the controlling device could only support the preset position numbers ES below 128 please use PELCO_D1 controlling protocol 6 1 2 Set up the Address of the High Speed Dome Camera Before actua
15. the high speed dome See the picture below 30 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br module tightening stud tightening screw hole 3 M4 0 installation hole for decoration cover Module Locate the three installing slots at the bottom of the module into the three pegs on the installation board be sure in right direction and lock them in place then swivel the module right for 20 to the point where the screw fixing hole in the module meets the corresponding stud Finally fix the module with the installation board with M3 screw and make sure it is tight D Install the decorating cover with the installation board tighten the screw 5 6 3 Connection of Exterior Cables Connect BNC video outlet of the High speed Dome Camera with the already disposed video cable the power cable with the already disposed power cable AC24V or DC14V and RS485 controlling cable with already disposed RS485 controlling cable The cables of high speed dome camera is shown below Power cable AC24V orDC14V high speed dome Power supply connecting outlet power supply power supply adaptor 31 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 485 cable 485 controlling high speed dome Green A white B signal controlling device Video Cable Camera
16. L MSEG ALM SPD20 1 Introduction siiani aan a EA a e Ra 3 II Technical Data ssmegtas andor chatieae Seca pardo ride pondo nf cano spap Gas Brasa ca CERs INTRA Aguda 3 HI Characteristics sci bck neice ieee ieee nsec a E 8 IV Description of FUNCHONS ss sss assis linsnerdtce avec urncannsaaniasiareaiedensaatonnaeces 9 V Installation and Connection of the DeVICES ccccccceseecteteeeteeeenees 14 5 1 Outer shape and Dimension of Wall mount Pendant mount and Ceiling mount High Speed Dome Camera s a a a indnesinaporino an E A E iE a E tata 14 5 2 Installation Style and Ancillary Components oi iii 16 5 3 Preparation for the Installation i ci ece ec ec eee eee eee eeeeeeeeeeea eee eeeeaeeeeeeees 17 5 4 Installation of Wall mount High Speed Dome Camera ecceeeneeeeeee teen etna 18 5 5 Installation of Pendant mount High Speed Dome Cametra 0eeeeeeeeneeee eee 24 5 6 Installation of Ceiling mount High Speed Dome Camera ii 27 5 7 Connection and Installation of Alarm ia 31 VI Setup of the functions of the High speed Dome Camera 34 6 1 Set up Address Baud Rate and Protocol for High Speed Dome Camera 34 6 2 Table for the Functions of the High Speed Dome Camera cceeeeeeeeneee ee 36 6 3 Set up and Preview Preset Positions iiii ece cence een eceeeeen eee eseeeeeee
17. allation instructions on the PCB board 3 The vitreous cover of the High speed Dome Camera is complicated optical component so do not touch it with bare hand s Otherwise the cover might be scraped and image quality affected 4 To ensure the clarity of images please clean the vitreous cover regularly Be careful when cleaning it You can only hold the outer ring of the vitreous cover Do not touch it with bare hand s for acid sweat left may erode the surface plating of the vitreous cover or hard things may scrape the vitreous cover leading to fuzzy image and hence affecting image quality Please use adequately soft dry cloth or other substitutes to clean the inner and outer surfaces If the vitreous cover is extremely dirty it may be cleaned with mild detergent 18 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 5 3 Preparation of the Installation To avoid mistakes installation must be done by qualified personnel conforming to related regulations Please check whether the attachments are all ready and whether the installing location and style of installation are compatible The wall mount and the pendant mount high speed dome camera is composed of bracket housings power adaptor decoding board pan tilt temperature controlling devices etc Well the ceiling mount high speed dome camera is composed of ceiling installing board
18. below 1 Set up the Left Limiting Position Operate the joystick towards left adjust the image to the desired postion then A Input 130 100 B Press PREVIEW key 2 Setup the Right Limiting Position After the Left Limiting position is set up well operate the joystick towards right adjust the image to the desired postion then A Input 131 101 B Press PREVIEW key After setting up well operate as below to run the scan 6 5 2 Start Left amp Right scan To start Left amp Right scan means that the user use an external order to start the scan and to make the speed dome scan between two limiting positions so that the user can monitor the corresponding district Three kinds of speed are optional 132 102 for low speed 133 103 for medium speed 134 104 for high speed The user can operate on the keyboard the operation is as below Operation through previewing function code a Input 132 102 44 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br b Press PREVIEW key Then the speed dome will scan between the two positions with low speed The setup method for other speeds are the same 6 6 Start 360 endless scan The Speed Dome can carry out 360 scan function So that all direction scanning and monitoring effect is realized Three kinds of speed are optional 135 for low speed 136 for medium speed 137 for high speed The user can operat
19. ceiling mount decorating cover housings power supply decoding board pan tilt etc When the High speed dome camera leaves factory it has undergone installation testing so the user can directly carry out the installation However for wall mount and pendant mount high speed dome before installation the user should open the vitreous cover and make sure the screws are tight and cable connectors not loose The sketch for the Installation of the Module into the Housing of the wall mount or pendant mount high speed dome Module Tightening Stud the hole through which the screw passes to tighten the Module A Three Installing Slot Locate the three installing slots at the bottom of the module into the three 19 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br pegs on the housing peg board be sure in right direction and lock them in place then swivel the module right for 20 to the point where the screw fixing hole in the module meets the corresponding stud Finally fix the module with the housing with M3 screw and make sure it is tight 5 4 Installation of Wall mount High speed Dome Camera 5 4 1 Installation of Wall mount Bracket Remarks The wall for the selected installation location must be firm without peeling To avoid quivering images resulting from unstable installation make sure the place for installa
20. e on the keyboard the operation is as below a Input 135 b Press PREVIEW key Then the speed dome will carry out 360 endless scanning The setup method for other speeds are the same 6 7 Stop Left amp Right scan and 360 scan While the unit is carrying out scanning operation if you require the unit carry out other operations you can operate on the keyboard to stop the auto scan Operation is as below a Input 138 108 b Press PREVIEW key The Auto Scan can also be stopped by any operation on the joystick of the keyboard 6 8 Open and close the menu of camera module The unit has a function as setting up the parameters of the Camera Module Users can open and close the menu of the camera by previewing 145 and 146 preset positions After entering the menu users can set up the camera conveniently The operation is as below 45 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 1 Open the menu of the camera a Input 145 95 b Press PREVIEW key 2 Close the menu of the camera a Input 146 96 b Press PREVIEW key Attention If the camera module doesn t have menu function this function with the unit is unavailable 6 9 Setup Activate and Exit the Default Position function The unit has a default position The user can set up default position for a key monitoring area according to actual conditions If not operated after 5
21. ect then switch on power b The High speed Dome Camera begins to do self check by moving pan 360 tilt 90 to check the camera lens the electrical and mechanical structures in pan tilt state then executing the restoration program and 28 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br resuming its original position After the High speed Dome Camera stops moving it finishes self check and is ready to receive controlling instructions c Use controlling device to control the High speed Dome Camera checking whether it can perform the functions of the pan tilt and camera lens If not please check the setup of communication protocol Baud rate and address and the connection of 485 controlling cable 5 5 5 Vitreous Cover Installation a Clean the dust and stain on the vitreous cover with soft cloth attention not to scrape the vitreous cover b Aim the four special bolts the bolts don t fall even if they are loosened to the extreme in the vitreous cover at the bolts holes in the outer housing then tighten the bolts 5 6 Installation of ceiling mount high speed dome camera 5 6 1 Installation of ceiling mount installation board Remarks The ceiling for the selected installation location must be firm without peeling To avoid quivering images resulting from unstable installation make sure the place for installation can sustain five times the
22. eeees 39 6 4 Set up and run Tour GroupsS c eccccee cece ec eee e eee eee eeeeeeee eee eeeeeeeeeeeeeeeeeeeenees 40 6 5 Set up and start Left amp Right Scan eee eeeeeeeeteeeneenerens TRT 42 6 6 Start 300 endless Scan cussgomasiopo sb olesi digas andas ai a a a a 43 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 44 6 9 Set up Activate and Exit the Default Position FUNGON asas gent aniraa ie nat 44 6 10 Open and close Fog Dispersing function eeeeeeeeeeeeee tere eees sea Meets 45 VII Tro ble Shooting s eszarsn me tet ennatendes mesa che Se onsha at oe ae a e 46 VIII Address coding corresponding table ccccccceccseeeseeeeeeseeeeneaees 47 Important Safeguards 1 During the course of transportation and storage the product should be avoided from incorrect operations such as heavy pressing strong vibration soaking etc which may cause damage to the unit 2 The product is designed for Wall mount Pendant mount or Ceiling mount installation so it can not be installed upside down And the module should be handled properly so as not to bring about mechanical problems affecting the integrative functions of it The vitreous cover of the dome is complicated optical component so do not touch it with bare hand s Otherwise the cover might be scraped and image quality affected 3 To ensure
23. eft amp right scanning Start running a tour medium speed Start Left amp right scanning Open Alarm Function high speed 102 Start Left amp right scanning low 111 Exit tour setup speed 39 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Start Pan tilt 360 scanning Close Alarm Function low speed Start Pan tilt 360 scanning Activate default position function medium speed Start Pan tilt 360 scanning 123 Close default position function high speed High speed dome camera Set up default position function position restoration Enter menu of the camera module EE Exit menu of the camera module Intelligent control and all of its functions can be realized through the Open the fog dispersing function Close the fog dispersing function keyboard s control over High speed Dome Camera Because different controlling system interfaces may differ in operation operation details are subject to the related manufacturer s manuals Under certain circumstances of special requirements and operations please refer to dealers for necessary information 6 3 Set up and Preview Preset Positions The function of preset positions works in this way the High speed Dome Camera saves the current pan tilt and zooming ratio parameters in number order 1 128 quickly previews those parameters when needed and adjust the dome to the
24. etr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 5 1 1 Outer shape and Dimension of Wall mount and Pendant mount High speed Dome Camera the Head for Installation 189 5 199 5 Dome Housing 765 Transparent Cover 1 157 0 lee mece e tel 5 1 2 Outer shape and Dimension of Ceiling mount High speed Dome Camera The outer appearance is defferent from the former two 16 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br I 9201 AS Z Vitreous Cover 193 75 ne 0138 ne 0146 a In 152 al 5 2 Installation Style and Ancillary Components 17 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Products Cable with connector Installation Style High Speed Wall mount Wall bracket Power Cable 1pc Dome Pendant mount Bracket with the length Ceiling mount No bracket 485 cable 1pc 5 strands cable Alarm input 2 strands cable Alarm output Remarks 1 The connection must be carried out by qualified personnel conforming to local regulations 2 For connection details please refer to the silk screen printing indications and inst
25. fast e When the object is large sized and drab such as wall e When the object is too dark or fuzzy Iris Control e The system takes auto iris as the default The iris can automatically sense the change of the environmental light and make quick adjustment so that the brightness of the image is stable e The user can manually adjust the iris through controlling the keyboard to obtain desired brightness for the image Automatic Back Light Compensation BLC Automatic Back Light Compensation can be realized via district dividing In extremely bright background the camera can compensate the brightness 14 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br of the relatively dark objects while adjust the light of the bright background avoiding that the whole image is too bright to watch due to the too high brightness of the background while the object is too dark to be distinguished so that the clear image can be got Automatic White Balance According to the ambient brightness the camera can automatically adjust the White Balance to re display the real color V Setup Installation and Connection There are three types of installation for high speed dome cameras the dimensions are shown below 5 1 Outer shape and Dimension of Wall mount Pendant mount and Ceiling mount High speed Dome Camera 15 Distribui o Tucano Comercio de Alarmes e Sistemas el
26. hich you need to preview and LED displays the preset position number Then press the PREVIEW key The High speed Dome Camera will return to the preset position e g Preview the No 1 preset position 41 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br a Enter 1 b Press PREVIEW key 6 4 Setup and run tour groups The tour group function is to group some preset positions together if the user wants to preview these preset positions with only one external order the High speed Dome Camera will automatically preview the preset positions in the group one by one The dwelling time at each preset position can be set within 1 255 seconds Up to 16 preset positions can be saved in each tour group And at most 4 tour groups can be set up The operation is as below A In the keyboard initial state enter number 140 110 and press the PREVIEW key to enter the tour setup B After entering the setup add preset position number to the tour Enter the first desired preset position number and press the PREVIEW key and the first preset position is successfully added Then goes the second one Enter the second desired preset position number and press the PREVIEW key and the second preset position is successfully added More preset positions can be added in the same way C After all the required preset positions having been added
27. l using the address of the High speed dome camera should be set up The switches 1 8 of SW1 on the PCB board is used to set address of the High speed Dome Camera from 1 to 255 The coding switches from DIP 1 to DIP 8 are equivalent to a 8 bit binary figure The state ON of each bit means 1 while OFF means 0 Corresponding state of coding switches and address is shown in the appendix table 6 1 3 Set up Baud Rate of Communication DIP 3 and DIP 4 of SW2 on the PCB board is used to set up Baudrate of communication the default setup is 4800BPS Following table shows states of coding switches and cosrresponding Baudrate saga Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 4 If protocol address and Baud rate are set up when power is on then the high speed dome camera must be switched off and restarted to make the setup valid Remark If the High speed Dome Camera is used at the farthest terminal there should be a parallel connection of a 1200 terminal matching resistor between A B lines of RS485 6 2 Table for the functions of the high speed dome camera Notice PELCO D protocol has no corresponding orders for part of the special functions so we converted functions of some of the commonly used orders generally converting in the way of preview preset position set up preset position Order converting correspondence is sh
28. llation of Pendant mount Bracket Remarks The ceiling for the selected installation location must be firm without peeling To avoid quivering images resulting from unstable installation make sure the place for installation can sustain five times the total weight of the High speed Dome Camera the bracket and the base A Use the bracket as template and draw the positions of the installing holes on the desired ceiling locus B Use an electric drill to make three holes for M6 screws on the above drawn positions and drive in the special M6 screws C Push the power cable communication cable and video cable through the bracket tube leaving long enough cables for connection D Fix the bracket firmly on the ceiling with three M6 screw nuts and washers 26 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Cable Slot 4000r200 5 5 2 Installation of High Speed Dome Camera a Unpack the carton and carefully take out the High speed Dome Camera and its attachments open the vitreous cover and take out the fillings b Check cable connectors and see if any of them loose and set up the coding switch c Put the connecting cables into the bracket tube then push the installing port on the top of the outer housing into the installing hole of the bracket tighten the 3 M6 screws and fix well Make sure the M6 screws just fit in the
29. ns smoothly reacts quickly and locates positions accurately Als Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br With varieties of high performances the high speed dome camera can be applied in every walk of life to monitor moving objects in large areas such as monitoring smart buildings bank city streets power departments airports bus railway stations etc II Technical Data 2 1 Technical Data of the High Speed Dome Camera DC14 30V 2A AC18 30V 2A 0 5 200 s 64 ranges Pratmovement Si e TT the changing of focal length following the change of the focal length Scan Preset position number in 16 preset positions ee ee of tour es es 4 Channels in 1 Channel out Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Address range of the speed 1 255 dome PFan Automatically start when the temperature is above 50 C Automatically start when temperature is below 5 C 2 2 Camera Module Data Built in Canon Camera Module Type Canon 22x color Canon 22x color day and night Focus auto manual E Auto System of signal NTSC PAL S N gt 50dB Video Signal output 1 0 0 2Vpp 2 3 Camera Module Data Built in SONY Camera Module Type SONY 18x color SONY 18x color day and night Synchronization Internal sync external sync Scan 2 1
30. o tucanobrasil com br 5 4 3 Connection of Exterior Cables Connect BNC video outlet of the High speed Dome Camera with the already disposed video cable the power cable with the already disposed power cable AC24V or DC14V and RS485 controlling cable with already disposed RS485 controlling cable The cables of high speed dome camera is shown below Power cable AC24V orDC14V high speed dome Power supply connecting outlet i ee TUTO 485 cable 485 controlling high speed dome Green A white B ee remonta TOO Video Cable Camera signal Camera BNC connector D re O 5 strand Alarm input Detctor Black Alarm input public terminal cable high speed dome Yellow the 1st channel alarm input Green the 2 channel alarm input Blue the 3 channel alarm input White the 4th channel alarm input 2 strand Alarm output High speed dome Brown alarm output public terminal cable alarm horn Grey alarm output terminal Make sure the polarity of RS485 controlling cable connection is correct A RS485 positive B RS485 negative 4 If wrongly connected the High speed Dome Camera will be out of control 24 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br The detailed connection as the sketch below
31. ot the camera should never be aimed at the sun or object with extremely bright light Otherwise the camera s CCD might be permanently damaged 7 There are no parts inside the unit which can be repaired by the users themselves When mechanical problems arise do not be in a haste to do any repairing please refer to the User s Manual to find the trouble If causes can not be located please refer servicing to qualified professionals All servicing must be done by authorized personnel Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br l Introduction Adopting latest technological achievements and cutting edge manufacturing techniques the JG QG900A Series High Speed Dome Camera is created with many years of accumulated experience Equiped with a high performance DSP camera with zooming lens integrating built in Pan tilt and digital decoder it represents the future trend of hi tech monitoring products The unit is capable of rapid positioning consecutively tracing and scanning which realizes real all directional monitoring The unit can automatically adapt to ambient brightness and object distance Its digital control and elegantly simple design maximally reduces the connection between differnent parts in the system which improves the reliability of the system and facilitate the installation and maintenance Driven by a stepper electric motar the unit ru
32. own in the following table Preview Keyboard operation meaning Preview Keyboard operation meaning preset preset position position No No A 130 Set up left limiting position Stop Pan tilt auto scanning A EEE Set up right limiting position Start tour setup 30 3 n A 132 Start Left amp right scanning 141 Exit tour setup mms TT 33 Start Left amp right scanning 142 Start running a tour o eama TO O ETR 4 i i 7 13 Start Left amp right scanning 14 Open Alarm Function high speed 38 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br 135 Start Pan tilt 360 scanning 148 Close Alarm Function 136 Start Pan tilt 360 scanning 162 Activate default position function 137 Start Pan tilt 360 scanning 163 Close default position function 150 164 High speed dome camera Set up default position function esmo eee 145 Enter menu of the camera 165 Open the fog dispersing function a a 146 Exit menu of the camera 166 Close the fog dispersing function e ad eee If preset position numbers larger than 128 could not be previewed on the controlling device please choose PELCO D1 protocol functions operation table as below Preview Keyboard operation meaning Preview Keyboard operation meaning preset preset position position No No Stop Pan tilt auto scanning Start tour setup Start L
33. preset position 142 112 to start running the tour and the High speed Dome Camera runs the tour and begins to scan in the order of 132 5346 If other devices are used to control the High speed Dome Camera due to the protocol limitation some special functions of the High speed Dome Camera may be not operational 6 5 Setup and start Left amp Right scan The speed dome camera has Left Right scanning function The user can set up the left and right limiting positions for the required left amp right scanning area When running the left amp right scan the unit will scan forwards and backwards between the left and right limiting positions consecutively 6 5 1 Set up Left amp Right limiting positions 43 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br The user can freely set a beginning point as the Left Limiting Position an end point as the Right Limiting Position Attention If the beginning point is the same as the end point the speed dome will scan 360 endlessly Meanwhile the unit will automatically record the zooming times of the lens at the beginning point and take this data as the constant zooming times of the lens when scanning also the unit will record the vertical angle of the beginning point and take this angle as the constant vertical angle when scanning The operation of setting up Left amp right limiting position is as
34. ress and the connection of 485 controlling cable 5 7 Connection and installation of alarm Connect the alarm cables according to the sketch below Once distinguishing the alarm signal coming in the speed dome will immediately act as per the process set before it will start the camera display the image of the alarm zone on the monitor adjust the speed dome to the alarm point and monitor the preset position record what happens at the alarm zone as soon as possible Connection of the alarm cables as the sketch below Attention a Alarm input must be ON OFF input signal any other types of input signal such as power voltage etc is possible to damage the unit When there are alarm signals from multi channels the unit will respond to them one by one the interval is 2 seconds b Once there is alarm signal coming in the unit will not respond to Scan Cruising etc functions Manual operation is needed to restore Scan Cruising etc functions c No matter the alarm funtion is opened or closed alarm output always responds For example if the alarm function of the unit is not open when the unit distinguishes alarm signal the unit will not be adjusted to corresponding preset position but the alarm output still responds d The operation method for alarm fuction is through previewing the No 147 117 preset position to open alarm function throuh previewing No 148 118 preset position to
35. signal Camera BNC connector monitoring device 5 strand Alarm input Detector Black Alarm input public terminal able high speed dome Yellow the 1st channel alarm input Green the 2 channel alarm input Blue the 3 channel alarm input White the 4th channel alarm input 2 strand Alarm output High speed dome Brown alarm output public terminal cable alarm horn Grey alarm output terminal Make sure the polarity of RS485 controlling cable connection is correct A RS485 positive B RS485 negative 4 If wrongly connected the High speed Dome Camera will be out of control 5 6 4 Switch on Power a Make sure the polarity of plugs sockets and cables connection is correct then switch on power b The High speed Dome Camera begins to do self check by moving pan 360 tilt 90 to check the camera lens the electrical and mechanical structures in pan tilt state then executing the restoration program and resuming its original position After the High speed Dome Camera stops moving it finishes self check and is ready to receive controlling instructions c Use controlling device to control the High speed Dome Camera checking whether it can perform the functions of the pan tilt and camera lens If not 32 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br please check the setup of communication protocol Baud rate and add
36. that the image from the High speed Dome Camera is crisp the vitreous cover of the Speed Dome should be cleaned periodically When cleaning please be cautious please note that only the outer ring can be held please don t directly touch the vitreous cover because the acid sweat from your hands may corrode the plating of the vitreous cover and any scrape on the vitreous cover may cause the image blur and infuence the quality of the image Please use dry cloth which is soft enough or other Lines Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br substitute to wipe the outer or inner surface If it is serious dirty netral cleanser can be used to clean the vitreous cover 4 Do not let any foreign objects or liquid infiltrate into the unit which may damage the unit 5 Please follow all electrical standards for safety when the unit is being connected and please adopt the particular power supply which is provided with the unit The product s RS 485 and video signal adopt TVS class lightning damage preventing technology which can effectively prevent such pulse signal damage caused by lightning under 500W or electric surge RS 485 and video signal should be kept enough distance from high voltage equipments and cables when they are in transmission and necessary steps should be taken to prevent lightning damage or power surge 6 No matter the unit is runing or n
37. the installed peg board then push the bracket downward until it locks in place Make sure the wall bracket is well fixed with the installation board then direct the screw on the bracket to the corresponding hole on the lower part of the installation board and tighten the screw See the figure below 21 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Tightening Screw 5 4 2 Installation of High Speed Dome Camera a Unpack the carton and carefully take out the High speed Dome Camera and its attachments open the vitreous cover and take out the fillings b Check cable connectors and see if any of them loose and set up the coding switch c Put the connecting cables into the bracket tube then push the installing port on the top of the outer housing into the installing hole of the bracket tighten the 3 M6 screws and fix well Make sure the M6 screws just fit in the screw slot of the installing port of the housing See the picture below 22 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Vo A Wall Bracket M6 Screw Screw Slot Wt Installation Head of the Housing 23 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucan
38. the preset positions into the tour e The tour order is programmable The staying time at each preset position can be set up e Sixteen preset positions can be stored in one tour Altogether 4 tours can be set up with the speed dome 6 Automatic Scanning Left right limiting positions can be set up through controlling keyboard 12 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br and the camera can automatically scan horizontally between the left limiting position and the right limiting position at the preset speed 7 Alarm Function User can set important position as alarm point Once there is alarm signal coming into the unit from external connected sensor the unit will immediately turn the lens to the alarm point at the same time output alarm signal through the Alarm output terminal 8 Default Position Function The unit supports default position function The user can set up default position for a key monitoring area according to actual conditions If not operated after 10 minutes the High speed Dome Camera will automatically monitor the default position 9 Camera Lens Control Users can adjust the Focal length through controlling the keyboard to get panoramic view or close view that they desire Focal Length Control Users can adjust the Focal length through controlling the keyboard to get panoramic view or close view that they desire
39. tion can sustain five times the total weight of the High speed Dome Camera the bracket and the base A Use the bottom installation board of the bracket as template and draw the positions of the installing holes on the desired wall locus aye Ancillary Hook Se Wall Bracket Installation Dimensions 20 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br B Use an electrical drill to make four holes for M6 screws on the above drawn positions and drive in the expansion M6 screws C Push the power cable communication cable and video cable through the bracket tube leaving long enough cables for connection D Fix the installation board of the bracket firmly on the wall with four M6 screw nuts and washers E Put the power adaptor into the wall bracket and pin the power adaptor with the adaptor pinning board lest the power adaptor slides out See the figure below Adaptor Pinning Board F Fix the high speed dome with the wall bracket refer to the detailed explanation in the next page G Put up the wall bracket assembled with high speed dome on the ancillary hooks Pull the power cable video cable and controlling cable out through the wire out going hole and direct the dotted line part shown in the figure to the two corresponding pegs on
40. vement no blind area for the monitoring Tilt 90 auto flip at the bottom which ensures consecutive monitoring 10 Distribui o Tucano Comercio de Alarmes e Sistemas eletr nicos Ltda Fone Fax 041 3286 2867 E mail tucano tucanobrasil com br Automatically adjusting movement speed according to lens zoom ratio Automatic Iris Focus and White Balance Manual Fog dispersing Function is realized IV Description of Functions 1 Trace the Target The users can control the movement of the camera by operating the joystick of the keyboard so that they can trace the moving object or change the monitoring area The angle of view or the size of the image of the object can be changed through adjusting the focal length In the default Auto focus Auto Iris state following the movement of the camera the lens will quickly adjust itself to get clear image according to the change of the object 2 Automatic Adjustment of Focal Length Movement Speed When the focus is long and in the mode of manual adjustment due to the high sensitivity of the High speed Dome Camera even the slightest movement of the joystick would make the image move quickly which causes image losses Based on human design the dome can automatically adjust the horizontal and vertical moving speed of the pan tilt according to the current focal length which makes the manual target tracing operation much easier 3 Automatic Flip In the process of operating the
Download Pdf Manuals
Related Search