Pro Color Strip Manual .pub
Contents
1. Note There is no serviceable parts inside the device except for the LED s Maintenance and service operations are to be carried out by authorized dealers Replacing the fuse Only replace the fuse with the same type and rating Replacing the power cable If the power cable of this device becomes damaged it has to be replaced by authorized dealers or trained professional only Should you have further questions please contact your dealer Parts List 3030 ps Power Supply 4000 dis Display 4000 fh Fuse Holder MEGAD WWW MEGA LITE COM Mega Lite 5718 Kenwick St San Antonio TX 78238 Ph 210 684 2600 Fax 210 855 6279 www mega lite com info mega lite com2. LR plugs and connectors in order to connect the controller with the fixture or the fixture with another DMxX i t DMX output Do inpu KN 1 Shield 2 Signal 3 Signal Caution At the last fixture the DMX signal needs to be terminated with a terminator Solder a 120 Ohm resistor between the and the signal into a 3 pin XLR plug and plug it in to the last fixture on the signal run Pre manufactured terminator plugs are available for purchase from your Mega Lite dealer HOS DMXT DMX Profile Pro Color Strip Mode A 3 Channel LED Color Red LED intensit 0 255 LED Color Green LED Intensity 0 255 LED Color Blue LED Intensit 0 255 Pro Color Strip Mode P 54 Channel pt te Color mn 0255 sae ee ee 1 a a e LED Color Green LED Intensity 0 255 LED Color Blue LED Intensity 0 255 Pro Color Strip Mode F 3 Channel Pt te color _ RedlEDintensiy cess No Function 0 1 Random slow to fast 40 59 Yellow 60 79 Purple 80 99 Aqua 100 119 Red Pulse 140 159 Green Pulse 160 179 Blue Pulse 180 199 Aqua Pulse 220 229 White Pulse 230 249 White LED Full 250 255 Dimmer Of to Ful 0 255 Main Control Menu The control board on the fixture base is your interface to access and control CONTROL BOARD all the functions on the unit Its digital display gives you a code view of the options and functions The following will explain each function and its options EEEE e Menu U
3. Tip User Manual Contents Safety Information Technical Information Main Power Connection DMX 512 Connection norms DMX Profile i a Main Control Rigging the Fixture Cleaning and Mainenance Parts List Check that the unit has not been damaged during transport Read all cautions and warnings prior to operation of this equipment Protection Against Fire Fire Maintain a minimum of 1 foot distance from any type of flame Replace fuse only with the specified type and rating Do Not install the unit to close to a heat source Make sure cable are properly secured away from unit movement Maximum surface operating temperature 80 0 0I 0 Protection Against Fire AN Electrical Disconnect power before servicing For connection to main power supply proceed to page 5 This unit must be earthed electronically grounded Do not expose unit to rain or moisture gt O Protection Against Mechanical Hazards 1 Use safety chain when hanging unit A 2 Use quality clamps or bolts when positioning unit 3 Do not open unit while it is on risk of electrical shock Mechanical Technical Information Part Numbers Fixture 3030 Pro Color Strip Mechanical Specifications DMX Connectors 3 pin amp 5 Pin XLR connectors Power Connection Neutrix Power Con in Out Thermal Maximum ambient temperature 40 C Maximum surface temperature 60 C Fastening System Single Mountin
4. g Yoke amp Security Eye bolt Accessories 1 Edison power head to Blue Power Conn cable 1 meter long 1 White Power Conn head Packaged for Shipping Size 40 x 6 x 3 Size 41 x 7 25 x 5 Weight 10 Ib Weight 12 Ibs Electrical Specifications LED Quantity 18 LED Type Tri Colored LED Watts 3 LED Lifetime 60 to 100 thousand hours LED Angle 45 5 Power Consumption 110V 220V50 60 Hz Ballast Electronic Watts 46 Amps 61 Control amp Programming Protocol DMX 512 DMX Channels Mode A 3 Channels R G B Mode P 54 Channels R G B X18 Mode F 6 Channels R G B Strobe Macro Dimmer Control options Audio trigger Operating mode Master Slave Main Power Connection Caution 1 Do not connect fixture to a dimmer system This unit has Auto switching power supply It will respond to 110V or 220V automatically 2 3 This unit must be earthed electronically grounded 4 Replace fuse only with the specified type and rating The occupation of the connection cable is as follows This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to 60Hz Cable USA Cable EU 110V 220V 110V 220V Connection Connection A Q 1 DMX 512 Connection The fixture is equipped with 3 pin XLR Sockets for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for RS 485 and 3 pin X
5. or to another Press Enter use the up down keys to select desired color change speed settings Press Enter to confirm the settings Chase Effect This function allows you to select different chase patterns on the whole strip Press Enter use the up down keys to select de sired chase settings Press Enter to confirm the settings Chase Speed This function allows you to select the speed of the chase that was selected on the Chase function Press Enter use the up down keys to select desired chase speed settings Press Enter to confirm the settings Sound Chase This function allows you to select the chase pattern that will be triggered via audio Press Enter use the up down keys to select desired Chase settings Press Enter to confirm the settings Sound Flash This function allows you to select the flash pattern that will triggered via audio Press Enter use the up down keys to select de sired dimmer settings Press Enter to confirm the settings Sound Sensor This function allows you to select the sensitivity of the audio sensor Press Enter use the up down keys to select desired dimmer settings Press Enter to confirm the settings Rigging the fikture Caution 1 The installations must be carried out by an authorized dealer or trained professional 2 Unit may cause severe injures if you have doubts concerning the safety do not install 3 Unit is to be 24inches away from flammable materials decoration material 4 Use high q
6. p Down Enter DMX Address Red Dimmer Green Dimmer Blue Dimmer Flash Fade Scroll Flash Scroll Chase Effect Chase Speed Sound Chase Sound Flash Sound Sensor ZI l I 1 I DC JC O oe joe T Ce Ce Z Z Z Z Z Rider EE 1 512 0 15 0 15 0 15 0 15 0 15 0 15 0 15 0 15 Loop Loop 0 15 Mode A 3 Channels R G B Mode P 54 Channels R G B x 18 Mode F 6 Channels R G B Strobe Macro Dimmer Red Dimmer This function allows you to dim the red LED s on the whole strip Press Enter use the up down keys to select desired dimmer settings Press Enter to confirm the settings JI l l Green Dimmer This function allows you to dim the green LED s on the whole strip Press Enter use the up down keys to select desired dimmer settings Press Enter to confirm the settings Blue Dimmer This function allows you to dim the blue LED s on the whole strip Press Enter use the up down keys to select desired dimmer settings Press Enter to confirm the settings Flash This function allows you to strobe the LED s on the whole strip in White color Press Enter use the up down keys to select de sired flash settings Press Enter to confirm the settings Fade Scroll This function allows you to fade the LED s on the whole strip from one color to another Press Enter use the up down keys to select desired fade speed settings Press Enter to confirm the settings Flash Scroll This function allows you to change the LED s on the whole strip from one col
7. uality installation equipment to hang unit When rigging a unit it is very important that you follow common safety procedures Rigging requires extensive experience includ ing but not limited to calculating working loads material being used and periodic safety inspections If you lack these qualifica tions do not attempt the installation yourself instead use a professional structural rigger When rigging the unit always be secured with a secondary safety attachment The installation location of the projector has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming Installation should be checked at least one time a year by a skilled person Cleaning and maintenance Installation Maintenance The operator has to make sure that the unit is operating safely and has the installations and electron ics checked by an expert every 2 years The following points have to be considered during the inspection 1 All screws used for installing the device or part of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing fixation and installation spots ceiling suspension trussing 3 The electronic power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed
Download Pdf Manuals
Related Search