GT24-B7066_QIG
Contents
1. one 1GB 240 pin DDR3 800 1066 1333 1600 MT s DIMMs e Hard Disk Drives SATA SAS e Rack Mount Kit Industry 19 rack mountable NOTE For an up to date list of compatible hardware please visit the system s support page on www tyan com Tools Required Anti Static Wrist Strap Phillips serewatives SS Yj 42 414039 38 37 3635 34 33 SS Flat head Dd 2 Motherboard Placement Motherboard Placement Open the Chassis Preparing the Chassis System Installation Read normal ESD Electrostatic Discharge procedures Place your TYAN Server Chassis on a flat anti static surface to perform the following integration procedures Read ESD procedures before reaching inside to install components Release the screw on the top cover Open the Install the processor and make sure the gold arrow is located in the right direction 32 31 WO CON OAAR WN 30 13 14 15 4 a0 gog 29 28 27 Am 17 18 19 2021 222324 25 26 16 561874870001 Loosen the 2 thumb screws on the back side Open the Open the CPU socket cover Close the CPU Close the socket cover socket lever CONNECTORS 1 USB2 0 ports and LAN Port 3 LAN3 shared with IPMI port 2 Vertical Type A USB Connector 3 Serial Port COM1 4 COM22. GT24 B7066 Quick Installation Guide Document D2230 100 Revision 1 0 etl General Information Read Me First 1 The Barebone User s Manual is available for download from our Web site at http Awww tyan com Make sure to read all precautions and instructions before you start installing the server system 2 Refer all servicing to qualified personnel to avoid the risk of damage to the server system 3 Exercise normal ESD Electrostatic Discharge procedures during system integration TYAN MiTAC recommends wearing gloves and an anti static wrist strap to avoid possible damage to the equipment 4 Current processor socket design places the pins on the motherboard instead of the processor itself Exercise caution when installing the processors as the manufacturer s warranty does not cover damage inflicted upon the motherboard including damage to the CPU sockets M1008 FPB M2091 Riser card 6 System fans M1235 HDD BP TYAN Quick Installation Guide a Sliding Rails x 2 amp Screw Pack x1 CPU heatsink x 2 Quick Installation Guide x1 Driver s and Utilities CD x 1 Required Hardware Components Minimum Hardware Requirements To avoid integration difficulties and possible board damage your system must meet the following minimum requirements e Processor Intel Xeon processor E5 2600 Series e Memory Type Minimum of
3. Header 5 ID LED Button 6 LAN Port 1 LAN1 7 LAN Port 2 LAN2 8 Port 80 Header 9 BMC 10 BIOS 11 Battery 12 ID LED 13 Reset Button 14 Flash Security Override Header 15 Power Button 16 17 USB Front Panel Header blue 18 19 Serial ATA Connector 20 SATA SGPIO Header 21 Serial ATA Connector SATA2 5 22 Mini SAS Connector SAS4 7 SLOTS A CPUO DIMM SLOT Channel A B B CPUO DIMM SLOT Channel C D C CPU1 DIMM SLOT Channel A B D CPU1 DIMM SLOT Channel C D E PCIE slot x16 F PCIE slot x16 1 Apply the thermal grease 3 Take off the top cover Press the locking lever and pull the locking lever open Remove the CPU protective cap Place a hard drive onto the drive tray Use four screws to 8 Close the other secure the HDD socket lever 23 Mini SAS Connector SASO 3 24 LSI IMR KEY 25 Front Panel Header 26 LAN3 LED Header 27 CPUO Fan Power Connector 28 Chassis Intrusion Header 29 Fan Connector SYS_FAN3 30 Fan Connector SYS_FAN2 31 Fan Connector SYS_FAN1 32 8 pin Power Connector PW3 33 CPU1 FAN Power Connector 34 PSMI Connector 35 IPMB Connector 36 HOST SMB Connector 37 8 pin Power Connector PW2 38 24 pin Power Connector PW1 39 SAS SMB Header 40 Fan Connector SYS_ FANS 41 Front Fan Connector reserved for Barebone 42 Fan Connector SYS_FAN4 JUMPER a ME Recovery Jumper b Clear CMOS Jumper c BIOS Recovery Jumper
4. d SPI Write Protect Jumper e LSI 2308 Enable Disable Jumper NOTE There is risk when setting the jumper by yourself Install the CPU Heatsink 2 Install the CPU heatsink 3 Unscrew the HDD tray bracket Reinsert the HDD tray into the chassis Locate the External I O Port Ethernet LAN3 shared with IPMI Ethernet OOOO VGA LAN1 LAN2 USB 2 0 Serial Port ID LED Button COM1 NOTE Please save and replace the CPU protection cap when returning the server board for service Press the locking lever to secure the tray Repeat the same procedures to install other HDD trays Install the Hard Disks 2 5 Place a hard drive onto the drive tray Use four screws to secure the HDD Press the locking lever latch and 2 Slide the HDD tray out pull the locking lever open Reinsert the HDD tray into the chassis Press the locking lever to secure the tray Repeat the same procedures to install other HDD trays Leip ha K AN AE JE WS wee LoS Hi S AN Insert the add on card to the riser bracket Make sure the add on card is latched unto the riser bracket ys in 4 Slt K K 9 Insert the riser cards to the PCIE slots as 8 Secure the riser bracket to the chassis with you align the riser bracket onto the chassis two screws NOTE To install the other add on card to the riser bracket please refer to the barebone user s man
5. ual on our Web site at http www tyan com for details www tyan com
Download Pdf Manuals
Related Search
GT24 B7066_QIG