User Manual - DAZA Opticare
Contents
1. the 4 screws on the rear of the Optiscan housing Replace the battery in accordance with Fig 3 Please note Plus pole on the right side After closing the Optiscan the sensor will require some time to calibrate This is shown by the i frequently illumination of the green LED behind the lens SEEEREEE Figure 4 Battery placement NEVER TOUCH THE ELEMENT IN THE SENSOR Serial number Set indication DAZA 4010 The serial numbers on both components of the set are the same This indicates that s n 401012072482 the transmitter and the receiver belong to each other Components of different sets are not interchangeable Figure 5 Serial numbers Entrance delay Standard between the detection of a movement and a transmission is a delay of 1 sec This delay gives you the time to switch off the receiver so that no alarm is received It is possible to change this time into 3 5 or 10 seconds You can do this by changing dipswitch 1 and or 2 Wl Wd 1 second default 1 2 ig 3 seconds 1 2 5 seconds a 2 Hf 10 seconds 1 2 Factory default settings Switch 3 to 8 should NEVER be changed When changes are made correct operation of the sensor can NOT be guaranteed w n m o m N E o m Daza Opticare BV follows a policy of continuous improvement in the development of its products The technical data can therefore be changed without notice This product is classified as an elec2. 4110 Ce Wireless Optiscan set acoustic 03 11 2014 V3 0 User Manual General This wireless Optiscan detects when a person intends to leave the bed This Optiscan works in combination with the corresponding Daza receiver which will sound an acoustic signal during the alarm Installation and use Insert the adapter into a power socket and the receiver is ready to use figure 1 power adaptor power socket receiver Figure 1 Receiver Optiscan placement Place the sensor on the floor facing the bed figure 2 Make sure that the sensor is placed safely where it can cause no harm to the inhabitant for example underneath a chair or table It is highly preferable to place it at a distance of at least 2 meters from the bed The sensor has a 90 degrees field of view over a distance of approximate 7 meter Make sure that no objects are in front of the sensor that can block its view figure 3 Switching on 1 The sensor is always on you need to switch on the receiver in order to receive the alarms press the orange button 2 Leave the room 3 The sensor switches itself on automatically once no movement across the floor has been detected for fifteen seconds Figure 3 Viewing angle sensor Confirm alarm 1 You can confirm the acoustic alarm by pressing the orange button once Switching off 1 You can switch off the receiver by pressing the orange button once 2 If there is an acoustic alarm you
3. need to confirm this alarm first before you can switch off the receiver Between detection of movement and activation of the transmitter there is a delay of 2 seconds This gives you the chance to deactivate the sensor before the transmitter is activated It is possible to extend this delay by an extra 3 or 5 seconds You can do this by moving jumper 2 to position three or five figure 4 Daza Opticare BV follows a policy of continuous improvement in the development of its products The technical data can therefore be changed without notice This product is classified as an electrical and electronic device When you decide to discard this product please ensure that this is done accordance with the European Directive on Waste Electrical and Electronic Equipment WEEE and compliant with local laws relating to this directive Page 1 of 2 4110 Ce X Wireless Optiscan set acoustic 03 11 2014 V3 0 User Manual Battery empty warning When the Optiscan battery is almost empty you get the 3 following messages Sensor element The LED behind the Optiscan lens blinks red every 5 seconds J The LED in the receiver blinks red every 2 seconds The receiver beeps 4 times when switching on an off W J hhi Battery replacement N Only replace this with a 3 6 volt lithium cell of size 2 3 AA aza Correct operation can only be guaranteed when an original battery of the brand 7 Saft type LS17330 is used Daza partnumber 7083 Remove
4. trical and electronic device When you decide to discard this product please ensure that this is done accordance with the European Directive on Waste Electrical and Electronic Equipment WEEE and compliant with local laws relating to this directive Page 2 of 2
Download Pdf Manuals
Related Search