OWNER`S MANUAL
Contents
1. Bentonville AR 72712 Toll Free 800 531 0004 TEL 479 273 6012 FX 479 273 2927 www whistlergroup com CUSTOMER RETURN CENTER 1412 South 1st St Rogers AR 72756 Customer Service Tel 800 531 0004 Email info whistlergroup com P N 404003 02 15 2015 The Whistler Group Inc2. then apply firm pressure for several seconds to insure a good adhesive bond e Ifthe MotoGlo is to later be reused a different helmet carefully remove the MotoGlo without damaging the LED extensions or center module e Clean the residual adhesive pads from the MotoGlo and replace with appropriate automotive molding adhesive pads or tape 4 Charging the MotoGlo Use the included USB cable to charge the MotoGlo The center indicator light is RED while charging and will turn GREEN when the MotoGlo is fully charged A standard USB to mini USB cable can also be used MotoGlo Operation Pairing on for initial operation e Install the Control Module and fully charge the MotoGlo Helmet Safety Light Refer to Power ON OFF for additional information NOTE If the MotoGlo does not automatically pair with the control module after initial charge or if pairing a second MotoGlo to the same control module the following steps are to be used to manually pair the MotoGlo with the control module 1 With the motorcycle ignition ON insert the Pairing Key into the mini USB interface on the MotoGlo MotoGlo should be fully charged 2 The MotoGlo has been successfully paired with the Control Module and activated when the Indicator Light turns BLUE 3 Remove the Pairing Key and the fidicator Light will turn RED 4 Store the Pairing Key in a place of safe keeping Power ON OFF The MotoGlo default is automatically in operational mode
3. Out Of Warranty Units will be repaired at out of warranty service rates when e The unit s original warranty has expired e A dated proof of purchase is not supplied e The unit has been returned without its serial number e The unit has been misused abused modified installed improperly or had its housing removed The minimum out of warranty service fee for your Whistler Helmet Safety Light is 35 00 U S If you require out of warranty service please return your unit as outlined in the section Service Under Warranty along with a cashier s check or money order in the amount of 35 00 Payment also be made by MasterCard VISA or American Express Personal checks are not accepted WARRANTY INFORMATION In the event repairs cannot be covered by the minimum service fee you will be contacted by a Whistler technical service specialist who will outline options available to you IMPORTANT When returning your unit for service be certain to include a daytime telephone number and an email address if applicable Customer Service If you have questions concerning the operation of your Whistler product or require service during or after the warranty period please call Customer Service at 1 800 531 0004 Representatives are available to answer your questions Monday Friday from 8 00 a m to 5 00 p m or visit the F A Q s at www whistlergroup com 10 CORPORATE HEADQUARTERS 1716 SW Commerce Dr Ste 8
4. Motorcycle Helmet Safety Light OWNER S MANUAL WHL 40 Half Helmet e WHL 80 Full or 3 4 Helmet lt p Ca LWHISTLER INTRODUCTION INSTALLATION Welcome NOTE The Control Module is designed for connection with multi wire t d not for CAN bus applications Thank you for choosing a Whistler product We are dedicated to providing 2 7 1 pranu is ihat path quality and valis Pipacs read the user 1 Using a computer safe test light probe volt ohm meter locate each carefully before using this product If you have additional questions please sues visit the FAQ page our website at www whistlergroup com or call toll eee 12V wh t t ON free 800 531 0004 8am to 5pm CT Monday through Friday to speak to a Bake Night Customer Service Representative Right Turn Signal Left Turn Signal Packing List NOTE On most motorcycles the wiring harness be located beneath MotoGlo Helmet Light the seat Control Module Pairing Key Wire Tap Connectors x 5 USB Charging Cable Owner s Manual Ignition Switch Positive cable for brake YELLOW g CONTROL BLUE Positive cable for right turn light Feature Description en Center Indicator Light ORANGE Positive cable for left turn light GREEN Ground 2 Using the provided wire taps and the wiring diagram above attach the wires of the CONTROL MODULE to the appropriate
5. ler product is warranted to the original purchaser for a period of one 1 year from the date of original purchase against all defects in materials and workmanship when purchased from an authorized Whistler retailer This limited warranty is void if the unit is abused misused modified installed improperly or if the housing and or serial numbers have been removed There are no express warranties covering this product other than those set forth in this warranty All express or implied warranties for this product are limited to one 1 year Whistler is not liable for damages arising from the use misuse or operation of this product including but not limited to loss of time inconvenience loss of use of your product or property damage caused by your product or its failure to work or any other incidental or consequential damages including personal injury DO NOT RETURN ITEM TO STORE WHERE PURCHASED FOR WARRANTY INFORMATION CONTACT WHISTLER CUSTOMER SERVICE AT 1 800 531 0004 Representatives are available to answer your questions Monday Friday from 8 00 a m to 5 00 p m CT Service Under Warranty During the warranty period defective units will be repaired or replaced with a same or a comparable model at Whistler s option without charge to the purchaser when returned prepaid with dated proof of purchase to the address below Units returned without dated proof of purchase will be considered out of warranty and therefore are not co
6. once properly paired with the control module With the motorcycle ignition ON the MotoGlo will power ON when it detects a slight movement of the helmet and will power OFF a few seconds after the motorcycle ignition is turned OFF NOTES 1 MotoGlo may also be manually turned OFF in the event the rider does not want the MotoGlo to operate while the motorcycle is in use as in situations with a passenger With the motorcycle ignition ON make sure the MotoGlo is within range of the control module and operating Apply and hold the brake and then operate left right left turn signals within 3 seconds and then release the brake The MotoGlo should now turn OFF 5 OPERATION OPERATION SPECIFICATIONS 2 Once manually turned OFF the same procedure must be used to power ON the MotoGlo IMPORTANT If 2 MotoGlo Helmet Lights have been paired to the control module the procedures above will affect BOTH helmet lights if they are in range of the control module If only one MotoGlo is to be manually turned OFF or ON make sure the other MotoGlo is in sleep status or out of range gt 100FT of the control module NOTE The MotoGlo will go into sleep status when the ignition is turned OFF and the MotoGlo powers OFF a few seconds later The MotoGlo will remain in sleep status until a slight movement is detected after the ignition is turned ON Running Lights The RED remain ON normal operating mode unle
7. ss changed by the user e The status of the running lights may be changed by operating the left right left turn signals within 3 seconds Each completed left right left cycle of the turn signals will advance the running light condition to the next status ON gt FLASHING gt OFF gt ON gt FLASHING gt OFF Turn Signals The AMBER lights will flash either right or left when the appropriate turn signal is activated on the motorcycle The running lights will go out while the turn signal is ON e When the brake is applied while turning the RED brake light will illuminate on the opposite side of the turn signal Left Turn Right Turn Brake Light The BRAKE lights will illuminate when the brake is applied and will be a brighter RED than the running light condition NOTES The center RED indicator light will remain illuminated regardless of operation unless the MotoGlo has been turned OFF center RED indicator light will flash when the battery needs to be recharged When this occurs the MotoGlo will no longer operate until the battery has been recharged Specifications Transmitter Receiver s a frcoen fem eo WHL 80 2 80z 78 59 Weight 02 9 WHL 40 2 70z 759 WHL 80 15 x 0 8 x 0 9 380 45 5 x 23 WHL 40 14 8 x 0 8 x 0 9 375 x 45 5 x 25 ae WARRANTY INFORMATION WARRANTY INFORMATION Consumer Warranty This Whist
8. vered by the described Limited Warranty Refer to Service Out of Warranty section Due to the specialized equipment necessary for testing Whistler products there are no authorized service centers other than Whistler When returning a unit for service under warranty please follow these instructions 1 Ship the unit in the original carton or in a suitable sturdy equivalent fully insured with return receipt requested to Whistler Repair Dept 1412 South 1st St Rogers AR 72756 Please allow 3 weeks turnaround time 8 IMPORTANT Whistler will not assume responsibility for loss or damage incurred in shipping Therefore please ship your unit insured with return receipt requested CODs will not be accepted 2 Include with your unit the following information clearly printed e Your name and physical street address for shipping PO Boxes a daytime telephone number and an email address if applicable e detailed description of the problem e g device will not power ON e A copy of your dated proof of purchase or bill of sale 3 Be certain your unit is returned with its serial number Units without serial numbers are not covered under warranty IMPORTANT To validate that your unit is within the warranty period make sure you keep a copy of your dated proof of purchase For warranty verification purposes a copy of your dated store receipt must accompany any Whistler product sent in for warranty work Service
9. wires of the MotoGlo Helmet Light motorcycle making sure that wire connections have good contact NOTE Electrical tape may be used to wrap the connections for better resistance to moisture STEP 1 STEP 2 Pairing Key Wire Connectors STEP 3 USB Charging Cable 2 3 Control Module INSTALLATION CHARGING OPERATION 3 Place the CONTROL MODULE in a weather protected area such as beneath the seat and secure to prevent movement Locate so that it does not interfere with other motorcycle components or wiring NOTE The CONTROL MODULE must be wired in line BEFORE any additional after market items such as taillight or brake light modulators Installation On Helmet 1 HELMETS VARY Before removing protective backing from the adhesive pads test fit the MotoGlo on the back base of helmet to determine best position and fit 2 Using isopropyl alcohol clean the area of the helmet where the MotoGlo is to be applied Allow the alcohol to dry 3 Remove the protective backing from the center adhesive pad and carefully apply the MotoGlo to the helmet in the predetermined area identified in step 1 making sure it is centered from left to right 4 Remove the protective backing from the LED extensions one at a time and carefully apply to the helmet NOTES adhesive is intended for a one time application It is best to lightly position the MotoGlo insuring proper location
Download Pdf Manuals
Related Search