RTS-200 User Manual Web Rev 1G.cdr
Contents
1. RadioTV Sync eSync Radio Sportscast to TV Broadcast Correct home theater Lip S ync timing eSync remote speakers to main Hi Fi RTS 200 USER MANUAL For Firmware Versions 1 16 and Later ELECTRONICS Product Features e Simple Setup amp Operation e Convenient control using included InfraRed IR Remote e Instantaneous Audio Mute function e Very High Quality Audio 48K 16 bit samples second per channel e 2 Channel Stereo Audio e Precise Delay Times in 1 100th second steps upto 43 00 seconds e Extra Precise Delays in 1 1000th sec steps 0 000 3 000 seconds e Delays up to 86 seconds available using Auxiliary Delay Modes e Delay settings preserved through power off on cycle e Line In passes through to Line Out when Power is Off e Product Includes RTS 200 120V 60 Cycle to 6VDC adaptor IR Remote Control with batteries 3 audio cables 1 3 5mm stereo audio to 3 5mm stereo audio cable and 2 3 5mm to twin RCA plug cables Typically this is everything needed to connect your audio source to your amplifier and speakers The Radio TV Sync Model RTS 200 is designed to delay audio from an AM FM radio tuner Satellite Receiver PC sound card or any audio source The audio is digitized stored and delayed with a variable delay period of from 0 000 seconds up to as much as 86 00 seconds The RTS 200 provides Extra Precise audio delays of up to three seconds suitable for restoring correct lip sync2. 2 3 5mm to dual RCA phono plugs foot mm E 56 N foot imin INANI E 1 This RTS 200 User Manual Built in 4 digit LED Delay Time Display 2 AAA included INCLUDED Audio Delay Unit Remote Control AAA batteries Power Adaptor 3 5mm 3 5mm audio cable 3 5mm to dual RCA phono plug audio cables User Manual Installation Plug RCA phono We strongly recommend NOT placing the RTS 200 Audio Delay Unit on top of your TV or other electronics due to possible Radio Frequency RF interference from that equipment Audio Systems vary widely plugs into jacks Representative This type of installation works Red Right tip Home with units having 1 or more of 3 3mm jack At east sets of RCA Phono style Audio White Left a ah A Jacks for Stereo Audio Input wi ono l Audio Jack Inputs Some sets will have jacks in the front Others in back Others Lice IN both front and back Plug RTS 200 s i i To complete the installation after plugging in adaptor into a 110V 60cycle receptacle For RTS 200CE adaptor plugs into a 220 volt receptacle DC power jack gt the RCA audio cables you may need to select the appropriate RCA Jack audio source using the Audio System s built in Operator Interface lt
3. Delayed Audio Output j Audio Source Input NOTE Locate the Audio REAO Plug into 3 5mm gt Delay Unit so that the stereo ear phone Delay Time Display gt jack T window is visible from your viewing position ooo gt Also be sure that there is a direct line of sight from J the Remote Control to the main unit Baer Aersesersoieewsds ss eee pogo AMPLIFIER ml ma oo 0 H H Plug RTS 200 s_ TUNER T adaptor into a Ea Delayed Audio Output ooo m E 110V 60cycle receptacle u For RTS 200CE adaptor plugs into a 220 volt receptacle RTS 200 DC power jack Typical Installations shown Adapt to your equipment as necessary i Audio Source Input During setup when adjusting the Audio Source volume setting we recommend setting the Delay Time to 0 000 seconds This will allow you to hear the result of volume adjust ments without waiting for a Delay Time that might otherwise have been selected Page 3 HOW IT WORKS RTS 200 Condition Display Activity l Power is Off While Powering Up Delay Time is 6 seconds or more Delay Time 3 6 seconds Delay Time lt 3 seconds Normal Operation Audio is Dela
4. RTS 200 unit not turned on being delayed Turning RTS 200 power on Noise high then pressing any Remote pitch or low Control push button pitch sounds at Output Changing Audio Delay Mode followed by pressing any key Making large changes to the Delay Time using the Auto Repeat feature of Display and Display push buttons PF displayed RTS 200 power is interrupt followed by ed Display showing PF is for audio noise or Power Fault If power re covers there may be audio blank display and no sound Output noise If power is lost output display goes blank and audio goes quiet RTS 200 is off Electrical noise Momentary 110 volt power failure other causes Other issues Press the MUTE button to exit MUTI NG mode Reduce Volume Set Audio Delay to 0 000 seconds Reduce Input Audio source volume until distortion goes away Plug it in Securely plug the wall adaptor into an active 110 Volt 60 cycle AC wall socket and the low voltage coax connector into the RTS 200 DC jack Check Replace Batteries Be sure batteries are inserted in the correct orientation Replace both if necessary Press PWR button Display will show current Audio Delay setting Adjust as desired with Delay and Delay keys The RTS 200 output audio signal may be being generated from random data in audio memory storage or from audio recorded for playback at a different data rate This sho
5. in high end audio equipment It may also be used to synchronize arrival time of audio from remotely located auxiliary speakers The RTS 200 is also ideally suited for synchronizing the audio from your team s partisan play by play sportscaster with the video from the sporting event Many people would rather listen to the sportscaster associated with their own team rather than those on the TV broadcast Since the TV signal goes through several satellite hops digital processing equipment etc before it gets to you it can be delayed by a few seconds to as much as 30 seconds or more RTS 200 UM Rev1G 2007 2014 MoTron Electronics All Rights Reserved DC Power Adaptor 110 volt 60 cycle AC to 6 volt DC 500ma center positive power adaptor _ or 220 volts AC to 6 Volt DC 500ma with the RTS 200CE version RTS 200 Audio Delay Unit NOTE The RTS 200 uses the F1 F2 and F3 buttons to control selection of the current Audio Delay Mode see page 6 The F1 and F2 keys are also used for controlling the Initial Power On State see page 6 PWR Toggle Power On Off DELAY F1 Previous Audio Delay Mode See Page 6 Next Fz Audio Delay Mode See Page 6 MUTE Toggle Audio Output Off On F3 Audio Delay Mode See Page 6 Page 2 What s I I ncluded InfraRed Remote batteries Decrease Delay Time DELAY Increase Delay Time 1 3 5mm to 3 5mm cable oo BE 0
6. S 200 to remain off when power is first applied press and hold down the F1 key until PoFF is displayed 3 sec RTS 200 Firmware Version The RTS 200 product is implemented using a combination a of electronic components including a microprocessor with weg Specialized control software When the MUTE push button is Down pressed and held down for 3 seconds the product s embed 3 sec ded software version is displayed while the MUTE key re mains down The three digit version number is preceded by an sign Release the MUTE key to return to Page 6 normal Delay Time display Troubleshooting SYMPTOM POSSIBLE CAUSES No sound at Output Input Output audio cables not plugged correctly Output amplifier or speakers not operating SOLUTIONS Sound source not operating ol To find out if the audio source input amp output cables amplifier and speakers are setup and work ing correctly Use the PWR button to turn off the RTS 200 The dis play will go blank The RTS 200 s relays will now pass the audio signals directly from the Input jack to the Output jack without delay RTS 200 in MUTING mode Display s decimal point will be flashing Output sound Input Audio Signal volume is is distorted too high No response to RTS 200 power adaptor not Remote Control plugged in and operating buttons Remote Control batteries worn out or not installed correctly Audio is not
7. lay Time is desired RTS 200 supports other Audio Delay Modes to cover this need Additionally the Lip Sync Mode supports finely controlled delay times of 0 000 to 3 000 seconds MODE DISPLAY DESCRI PTION Normal HS43 Normal Stereo High Resolution 43 00 seconds max delay Stereo LS86 Stereo Low Res 24 000 s s 86 00 seconds max delay Left Channel HL86 High Res Left Ch Audio to both L amp R outputs Max 86 00 secs Right Channel Hr86 High Res Right Ch Audio to both L amp R outputs Max 86 00 secs Monophonic Hb86 High Res Both Ch Audio to both L amp R outputs Max 86 00 secs Lip Sync LiPS High Res Both Ch Audio to both L amp R outputs Max 3 000 secs View Change Audio Delay Mode To see or change the selected Delay Mode press amp hold down the F3 key After 3 seconds the current Audio Delay Mode will be displayed see table above Release the F3 key Now you may use F1 and or F2 keys to select previous next Audio Delay Mode When a PWR Delay Delay MUTE key or no key is detected within 30 seconds the RTS 200 abandons the View Change Delay Mode display returning to regular Audio Delay operation without changing the Audio Delay Mode To save a newly selected Audio Delay Mode press amp release the F3 key Audio Delay will continue using the new delay mode Power Up Option To have RTS 200 start up immediately when power is applied Press and hold F2 until P on is displayed 3 seconds To configure RT
8. roduct under normal use will be free from defects in materials and workmanship MoTron Electronics entire liability and your exclusive remedy under this warranty which is subject to you returning the RTS 200 to MoTron Electronics with a copy of your receipt will be at MoTron Electronics option to replace the defective product or to refund the purchase price and terminate this Agreement No other warranties exist expressed or implied In no event will MoTron Electronics be liable for any damages including loss of data lost profits cost of cover or other special incidental consequential or indirect damages arising from the use of the RTS 200 product or accompanying documentation however caused and on any theory of liability This limitation will apply even if MoTron Electronics has been advised of the possibility of such damage Buyer acknowledges that the purchase price license fee reflects this allocation of risk Some states do not allow the limitation or exclusion of liability for incidental or consequential damages so the above limitation may not apply to you cust service motron com MoTron Electronics 1500 Renne St Look for more info on the PO Box 2748 RTS 200 and other great Eugene OR 97402 0280 Contact MoTron products on the web at www motron com Page 8 Tel 541 687 2118 Fax 541 687 2492
9. uld clear up after a Wait for the full Audio Delay period If power recovers RTS 200 will continue normally after noise pop is over If problem persists con sider plugging RTS 200 into power conditioner and or removing elec trically noisy appliances Cycle Power Unplug the AC power adaptor either from wall or RTS 200 wait 30 seconds re plug adaptor Please check for additional Troubleshooting Tips at www motron com Page 7 Specifications RTS 200 Audio Delay Unit WEIGHT 8 ounces SIZE 5 5 L x 2 6 W x 1 1 H POWER 6 volts DC 500ma Connector is center positive AUDIO Full CD quality hi fi stereo 48KHz 16 bit audio Delay Time Resolution 0 000 to 3 000 seconds in 1 milli second steps Lip Sync Mode 0 00 to 43 00 seconds in 10 milli second steps Normal Mode 0 00 to 86 00 seconds in 10 milli second steps Other Modes Relay passes audio through directly when power is off Maximum Delay Time High Resolution Stereo Normal Mode 43 00 seconds Additional available modes see page 6 86 00 seconds USER INTERFACE All functions controlled by included Infra Red Remote Control 4 digit 0 4 LED numeric Delay Time display Delay Time and other settings preserved through power off on Limited Warranty MoTron Electronics warrants that for a period of twelve 12 months from the date of purchase by the original buyer as evidenced by a copy of the receipt the RTS 200 p
10. ush buttons In this case the display will immediately show the current Delay Time setting and activate the output audio This may result in strange audio being output until RTS 200 has fully filled the audio delay data buffer D Use the Delay and or Delay push buttons to adjust the displayed Audio Delay Seconds to the Delay Time desired These keys both auto repeat when held down Auto repeating starts with changes to the units digit of the displayed Delay Time After four 1 s digit changes the next auto repeat changes are applied to the 10 s digit After six 10 s digit changes further auto repeat changes are made to the 100 s digit The F1 F2 and F3 push buttons may be used to view and control the currently selected Audio Delay Mode This setting controls the Input Channels left and or right passed on to the audio outputs max delay time and resolution See page 6 Use the MUTE push button to toggle entry exit into out of Muting Mode By pressing and holding down the MUTE push button the RTS 200 s software version my be seen See page 6 A 5 age Audio Delay Modes The Normal Mode for the RTS 200 Audio Delay product is to capture 48 000 audio data samples for each channel Left amp Right every second At this High Resolution data rate the RTS 200 is able to support Delay Times up to 43 00 seconds While this Maximum Delay Time is almost always sufficient there are uses in which more Audio De
11. yed Normal Mode delay up to 43 00 seconds Other Modes delay up to 86 00 seconds Lip Sync Mode delay up to 3 000 seconds Page 4 C Message is scrolled through the 4 digit dis Audio buFF example example nt oF f example When Output Audio _ is Muted silent the Delay Seconds decimal point will be flashing Wied example d tigit display Description amp Operator Control Options The Blank Display indicates that the power is off In this condition the Line In source audio is passed directly through to the Line Out output audio destination with no audio delay run The PWR push button may be used to power up the RTS 200 when it is off and to power down the unit when it is running While powering up the RTS 200 quiets the outputs while collecting audio data The Fill Audio BUFFEr example ee eee ie message scrolls through the display when the audio delay is 6 or more seconds After scrolling and for Delay Times between 3 and 6 seconds the remaining buffer fill seconds are displayed The RTS 200 will have filled the delayed audio data buffer by the time the displayed count down reaches zero It then turns on the audio outputs and displays the current Delay Time eel To save time you may begin adjusting the Delay Time value while the RTS 200 is filling the audio delay data buffer using the Delay and or Delay p
Download Pdf Manuals
Related Search