IGS-504HPT-UserManual
Contents
1. OFF Default ON Fiber Redundant DIP 3 Fiber Redundant Switch Port 6 DIP 2 1000X 100FX Port 5 DIP 1 1000X 100FX 2 1 2 LED Indicators System LED Color Function P1 Green Light indicates power 1 has power P2 Green Light indicates power 2 has power FAULT Green Light indicates either power 1 or power 2 has no power 10 100 1000Base T Interfaces LED Color Function Light indicates the Switch is successfully connecting to the network at 1000Mbps Blink indicates that the Switch is actively sending or Green N receiving data over that port OFF indicates that the Switch is inactively sending or receiving data over that port LNK ACT Light indicates the Switch is successfully connecting to the network at 10Mbps or 100Mbps Blink indicates that the Switch is actively sending or Orange ae receiving data over that port OFF indicates that the Switch is inactively sending or receiving data over that port Light indicates the port is providing 52V DC in line PoE In Use power Orange Port 1 4 OFF indicates the connected device is not a PoE Powered Device PD 100 1000Base X SFP Interfaces IGS 624HPT LED Color Function Light indicates the Switch is successfully connecting to the network at 100 1000Mbps Blink indicates that the Switch is actively sending or receiving data over that port LNK ACT Green OFF indicates2. Ai AW GENGGOH GO ES Dz Tee L elai a Gau ien aa Aa aga A Kanaan Na EA Nan a GN aa a aa dad aa aga O Cable Connection Parameters veces aa nyan aas ag eng a ga ag anja ga anda nana ga aan a ag aa aaa gana APPENDIX Az Networking sasana aaa ang aa a Ze a a ela SIA a rarus Sa aana ES A 1 PoE RJ 45 Port Pin Assignments End Span ss sasra sra gya rT ng naas aia a aaa A 2 Switch s RJ 45 Pin Assignments 022224222222 vesse memes A 3 RJ 45 Cable Pini Assignments eiecerunt a RR S Ra rh ia rax 1 Introduction Thank you for purchasing PLANET Layer 2 Industrial Gigabit Switch with 4 Port 802 3at PoE IGS 504HPT IGS 624HPT The descriptions of these models are as follows IGS 504HPT Industrial 5 Port Gigabit Switch with 4 Port 802 3at PoE 40 75 degrees C IGS 624HPT Industrial 4 Port 10 100 1000T 802 3at PoE 2 Port 100 1000X SFP Ethernet Switch 40 75 degrees C In the following section the term Industrial Gigabit PoE Switch means the IGS 504HPT amp IGS 624HPT 1 1 Package Contents Open the box of the Industrial Gigabit PoE Switch and carefully unpack it The box should contain the following items Industrial Gigabit PoE Switch x 1 User s Manual x 1 DIN Rail Kit x 1 Wall Mount Kit x 1 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material
3. SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with the same pin assignment and color as the above picture before deploying the cables into your network Q PLANET Networking amp Communication EC Declaration of Conformit For the following equipment Type of Product Industrial 4 Port 10 100 1000T 802 3at PoE 2 Port 100 1000X SFP Ethernet Switch Industrial 5 Port Gigabit Switch w 4 Port 802 3at PoE Model Number IGS 624HPT IGS 504HPT Produced by Manufacturer Name Planet Technology Corp Manufacturer Address 10F No 96 Minguan Rd Xindian Dist New Taipei City 231 Taiwan R O C is herewith confirmed to comply with the reguirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN 55022 Class A 2010 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN 55024 2010 EN 610
4. 1000Base ZX Single mode 9 N A 70 000 The Single mode port 1000Base LX port of IGS 624HPT complies with LX 5 kilometers and provides additional margin allowing for 10 20 30 40 50 70 120 kilometers Gigabit Ethernet link on single mode fiber APPENDIX A Networking Connection A 1 PoE RJ 45 Port Pin Assignments End Span PIN NO RJ 45 POWER ASSIGNMENT e Power 12345678 2 e Power 3 e Power 4 e Power A 2 Switch s RJ 45 Pin Assignments 1000Mbps 1000Base T Contact MDI MDI X BI_DA BI_DB 2 BI_DA BI_DB 3 BI_DB BI_DA 4 BI_DC BI_DD 9 BI DC BI DD 6 BI DB BI DA 7 BI_DD BI_DC 8 BI_DD BI_DC 10 100Mbps 10 100Base TX RJ 45 Connector pin assignment Contact MDI MU Media Dependant Interface Media Dependant Interface Cross Tx transmit Rx receive Tx transmit Rx receive Rx receive Tx transmit 4 5 Not used 6 Rx receive Tx transmit 7 8 Not used 33 1 A 3 RJ 45 cable Pin Assignments The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection 1234567 1234567 SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown
5. B m P NO N U 30 252 ___ 236 AA o E o 2 o o 9 2 152 136 0000000000 7 0000000000 q d 0000000000 B 0 0000000000 0000000000 E 0000000000 0000000000 0000000000 d 5 q 0000000000 H nm q oooooooooo g o oooooooooo al d o B 8 a a B a a p S 0000000000 B n B 0000000000 A 3 d 9000000000 7 8 d 8 8 8 9000000000 R g q B 3 b 3338 QPLRNET Industrial ETEREEIEZTRER Gigabit Switch IGS amp 24HPT T2 111 2 Installation This section describes the functionalities of the Industrial Gigabit PoE Switch s components and guides how to install it on the desktop Basic knowledge of networking is assumed Please read this chapter completely before continuing 2 1 Product Description High Power PoE for Security and Public Service Applications To fulfill the demand of High Power PoE for network applications with Gigabit speed transmission under wide temperature the IGS 504HPT and IGS 624HPT provide 4 10 100 1000Mbps ports featuring both IEEE 802 3af and IEEE 802 3at Po
6. Package Contents css ciii uices bns aaa aga uxo maa nn RA nA ef AT aa 1 2 How to Use This Manual arana dau mad naa ES TT ara ne pace 1 3 Product mi asa dasa ag ern a a AANE AN KEN KA HER HER FFA RF 1 4 Product SpecificatlOn See ane OL ana an Ngagengna KER ajaa aaa yy nn Dn O 1 5 Physical DIMENSIONS vetare aaa Ang yon an Zum 2 1 Product DescriptlOnD uices ruta tr etae saxa O O O O Oi OY IFE 2 1 1 Switch Front Panel ii ren aa aaa runc sa aan ajaa a 2 1 2 WED Indi CatOrs iiir sition GLY a ka DA E FAU YOU Gw Ri Rene 2 1 3 Switch Upper Panel iere iretur en pa seen netur ian ze tl anc ux 2 1 4 Wirinig the Power INPUtS cesserit ora venir o nter na 2 1 5 Wiring the Fault Alarm Cont cto speriene isuse rnnt mean puslHe pM 2 1 7 Redundancy OVerVl amp W cii oa a aaa alate a a ara ed a ajaa npe aui tl encanta 2 2 Mounting Installation sawana anaa Sesa ska aga ajaja he 2 2 1 DIN Railmountitid a sedan Sana aapa a E 2 2 2 Wall Mount Plate Mountirid legan agan aa a 3 Nele 63860 Sir rasa a ja ap jaka aa NA AN E E Na 4 Witch Operation uey aaa naa ana a Ga mang a aga 4 1 AddressnIable saa aana aaa aia anganani v AN E T Tan aje a pn EE EID LEE TEN ea Fa II 4 3 aaa SE aaa aa nai niet ag KN ga N 4 4 sells Seal Gan
7. PoE Switch will light up Please refer to the LED Indicators section for the functions of LED lights Prepare the twisted pair straight through Category 5 cable for Ethernet connection Insert one side of Category 5 cable into the Industrial Gigabit PoE Switch Ethernet port RJ 45 port and the other side of category 5 cable to the network devices Ethernet port RJ 45 port eg switch PC or Server The UTP port RJ 45 LED on the Industrial Gigabit PoE Switch will light up when the cable is connected with the network device Please refer to the LED Indicators section for the functions of LED lights When all connections are set and all LED lights show normally the installation is complete Be sure the connected network devices support MDI MDI X If it does not support then use the crossover category 5 Cable 4 Switch Operation 4 1 Address Table The Industrial Gigabit PoE Switch is implemented with an address table This address table is composed of many entries Each entry is used to store the address information of some nodes in network including MAC address port no etc This information comes from the learning process of Industrial Gigabit PoE Switch 4 2 Learning When one packet comes from any port the Industrial Gigabit PoE Switch will record the source address port number and the other related information in address table This information will be used to decide either forwarding or filtering for f
8. Testing IEC60068 2 32 Free fall IEC60068 2 27 Shock IEC60068 2 6 Vibration Environment Temperature Operating 40 75 degrees C Storage 40 75 degrees C Humidity Operating 59590 Non condensing Storage 59590 Non condensing Imensions 1 5 Physical D m IGS 504HPT Industrial Gigabit PoE Switch dimensions W x D x H 161 x 107 x 72 mm 40 000000000d00000000 0000000eed4eeooooooo 000000000d00000000 000000000d00000000 000000000d00000000 0000000e6e466600000 0000000004d00000000 000000000d00000000 0000000004d00000000 0000000004d00000000 98 A mo E E l 0 oo 7 o ff P x i S aT 8T 0g p 000000 0000 000000 0000 000000 0000 nuncu oooo 000000 0000 000000 oooo 000000 0000 000000 0000 9600000 0000 E 000000 0000 8 amp 0 SG9E uL QPLANET Industrial Gigabit Switch 14405591 10 IGS 624HPT Industrial Gigabit PoE Switch dimensions W x D x H 161 x 107 x 72 mm 28 H
9. and Forward mechanism with high performance on the other hand when in the 4 2 fiber redundant mode it provides rapid fiber redundancy of link for highly critical Ethernet applications The redundant mode also supports auto recovering function if the destination port of a packet is link down it will forward the packet to the other port of the backup pair 2 1 1 Switch Front Panel Figure 2 1 shows the front panels of IGS 504HPT and IGS 624HPT Industrial Gigabit PoE Switches e eee P1 P2 FAULT 1000 LNK ACT A 100 40d P C09 B S 2 eo I 5 w land E rm uz a G S e o a IGS 504HPT Figure 2 1 IGS 504HPT amp IGS 624HPT Front Panels B PoE Power Usage LED The front panel of the Industrial Gigabit PoE Switch has four LEDs which indicate PoE Power Usages W of 30W 60W 90W and 120W With these LED indications you can monitor current PoE power in use status of Industrial Gigabit PoE Switch easily and efficiently PoE Power Usage W 70 6 60 amp 306 13 m DIP Switch The front panel of the IGS 624HPT provides one 3 DIP Switch which is for configuring 100 or 1000X fiber support and fiber redundant function Refer to the table below to know about the 3 DIP switch settings and descriptions For more information about the fiber redundancy function please refer to the chapter 2 1 7 Redundancy Overview
10. for the terminal block should be in the range between 12 and 24 AWG 2 1 5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below Inserting the wires the Industrial Gigabit PoE Switch will detect the fault status of the power failure or port link failure available for managed model and then forms an open circuit The following illustration shows an application example for wiring the fault alarm contacts tt tl EE BJE EB The Fault Alarm Contacts are expe energized CLOSE for normal operation and will OPEN when Fault failure occurs Fault Alarm Contacts 1 The wire gauge for the terminal block should be in the range between 12 24 AWG 2 Alarm relay circuit accepts up to 30V max 3A currents 2 1 6 Cabling 10 100 1000Base T All 10 100 1000Base T ports come with Auto Negotiation capability They automatically support 1000Base T 100Base TX and 10Base T networks Users only need to plug a working network device into one of the 10 100 1000Base T ports and then turn on the Industrial Gigabit PoE Switch The port will automatically runs in 10Mbps 20Mbps 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after the negotiation with the connected device 100Base FX 1000Base SX LX The IGS 624HPT Industrial Gigabit PoE Switch has two SFP interfaces that support 100 1000 dual speed mode Optional Multi mode
11. power down the Industrial Gigabit PoE Switch as the Figure 2 3 appears v 2 2 r4 f 4 MGB MFB Series Transceiver Figure 2 3 Plug in the SFP transceiver m Approved PLANET SFP Transceivers PLANET Industrial Gigabit PoE Switch supports both Single mode and Multi mode SFP transceivers The following list of approved PLANET SFP transceivers is correct at the time of publication Fast Ethernet Transceiver 100Base X SFP Model A e bad Fiber Mode Distance Meee Rae MFB FX 100 LC Multi Mode 2km 1310nm 0 60 C MFB F20 100 LE Single Mode 20km 1310nm 0 60 C MFB F40 100 LC Single Mode 40km 1310nm 0 60 C MFB F60 100 LC Single Mode 60km 1310nm 0 60 C MFB F120 100 LC Single Mode 120km 1550nm 0 60 C MFB TFX 100 EC Multi Mode 2km 1310nm 40 75 C MFB TF20 100 LC Single Mode 20km 1550nm 40 75 C Fast Ethernet Transceiver 100Base BX Single Fiber Bi Directional SFP Model Speed Connector Fiber Distance Wavelength Wavelength Operating Mbps Interface Mode TX RX Temp MFB FA20 100 WDM LC i 20km i310nm 1550nm 0 60 C Single MFB FB20 100 WDM LC Moda 20km 1550nm 1310nm 0 60 C Single MFB TFA20 100 WDM LC Mode 20km 1310nm 1550nm 40 75 C Single MFB TFB20 100 WDM LC Mode 20km 1550nm 1310nm 40 75 C Single MFB TFA40 100 WDM LC Mode 40km 1310
12. that the Switch is inactively sending or receiving data over that port Per PoE Power Usage Unit Watts Lower LED to upper LED Lights to indicate the system is providing gt 30 Watts PoE power usage Lights to indicate the system is providing gt 60 Watts PoE power usage Lights to indicate the system is providing gt 90 Watts PoE power usage Lights to indicate the system is providing 2120 Watts PoE power usage 2 1 3 Switch Upper Panel The upper panel of the Industrial Gigabit PoE Switch consists of one terminal block connector within two DC power inputs Figure 2 2 shows the upper panel of the Switch Figure 2 2 shows upper panel of Industrial Gigabit PoE Switch Oo O Qr 6 QUO A O Oy OY 9 O LO QU O O O O CO O It OO L PWR1 ault Input DC 48V Figure 2 2 Industrial Gigabit PoE Switch Upper Panel 15 2 1 4 Wiring the Power Inputs The 6 contact terminal block connector on the top panel of Industrial Gigabit PoE Switch is used for two DC redundant powers input Please follow the steps below to insert the power wire 1 Insert positive negative DC power wires into contacts 1 and 2 for POWER 1 or 5 and 6 for POWER 2 PWR1 a Input DC 48V V1 VI V2 V2 2 Tighten the wire clamp screws for preventing the wires from loosening 1 2 3 4 5 6 Power 1 Fault Power 2 The wire gauge
13. transceivers DIP 1 SFP Port 5 1000Base X default 100Base FX DIP 2 SFP Port 6 1000Base X Copper Ports DIW default 100Base FX DIP 3 Switch default Fiber Redundant mode Terminal Block Connector Pin 1 2 for Power 1 Pin 3 4 for alarm Pin 5 6 for Power 2 Alarm Provides one relay output for power fail Alarm Relay current carry ability 1A DC 24V LED 3 x LED for System and Power m Green DC Power 1 m Green DC Power 2 m Green Power Fault 2 x LED for Per Copper Port Port 1 Port 4 m Green 1000 LNK ACT Orange 100 LNK ACT m Orange PoE In use 1 x LED for Per mini GBIC interface IGS 624HPT Port 5 and Port 6 m Green LNK ACT 4 x LED for PoE Power Usage W m Orange 30 60 90 and 120W ESD Protection 6KV DC EFT Protection 6KV DC Enclosure IP30 type metal case Installation DIN rail kit and wall mount ear Dimensions 152 x 107 x 72mm Weight 1478g 1539g Power Reguirement 48V DC 5A max Redundant power with polarity reverse protection Power Consumption 134 1 watts del gan 4 watts 461 BTU Dissipation BTU 10Base T 2 Pair UTP CAT 3 4 5 up to 100 meter Twisted Pair 100Base TX 2 Pair UTP CAT 5 5e up to 100 meter 1000Base T 4 Pair UTP CAT 5e 6 up to 100 meter 1000Base SX 50 125um or 62 5 125um multi mode fiber optic cable up to 550m 1000Base LX Cable Fiber Optic Cable 9 125um single mo
14. uses IGS 801 PLANET 8 Port Industrial Gigabit Switch as the example However the steps for PLANET Industrial Gigabit PoE Switch are similar 2 2 1 DIN Rail mounting The DIN Rail is screwed on the Industrial Gigabit Ethernet Switch when out of factory When needed to replace the wall mount application with the DIN Rail application on Industrial Gigabit Ethernet Switch please refer to the following figures to screw the DIN Rail on the Industrial Gigabit Ethernet Switch To hang the Industrial Gigabit Ethernet Switch follow the steps below Step 1 Screw the DIN Rail on the Industrial Gigabit Ethernet Switch 4A24 Step 2 Lightly insert the bottom of the switch into the track Step 3 Check if the DIN Rail is tightly on the track Step 4 Please refer to the following procedures to remove the Industrial Gigabit Ethernet Switch from the track 25 1 Step 5 Lightly pull out the bottom of the switch for removing it from the track 2 2 2 Wall Mount Plate Mounting To install the Industrial Gigabit Ethernet Switch on the wall please follow the instructions described below Step 1 To remove the DIN Rail from the Industrial Gigabit Ethernet Switch loose the screws to remove the DIN Rail Step 2 Place the wall mount plate on the rear panel of the Industrial Gigabit Ethernet Switch Step 3 Use the screws to screw the wall mount plate on the Industrial Gigabit Ethern
15. 00 4 2 2009 EN 61000 4 3 2006 A1 2008 A2 2010 EN 61000 4 4 2004 A1 2010 EN 61000 4 5 2006 EN 61000 4 6 2009 EN 61000 4 8 2010 EN 61000 4 11 2004 Responsible for marking this declaration if the Manufacturer Ll Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 10 No 96 Minguan Rd Xindian Dist New Taipei City 231 Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Product Manager Taiwan 3 June 2013 idi Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw http www planet com tw 10F No 96 Minquan Rd Xindian Dist New Taipei City Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528 This page is intentionally left blank
16. 04HPT IGS 624HPT port 1 to port 4 to the other end The cable should be an 8 wire UTP Category 5 or above EIA568 cable within 100 meters A cable with only 4 wire short loop or over 100 meters all will affect the power supply Please check and assure the device is fully complied with IEEE 802 3af IEEE 802 3at standard Can I install MGB SX or other non wide temperature SFP module into SFP slot of Industrial Gigabit PoE Switch Solution Yes you can However since the MGB SX and other non wide temperature SFP modules cannot operate under 40 degrees C it must be brought to attention Please pay attention to this point 31 6 Cable Connection Parameters The wiring details are as below 100FX Fiber Optical Cables Standard Fiber Type Cable Specification Multi mode 50 125um or 62 5 125um 100Base FX 1310nm Single mode 9 125um 100Base BX U TX 1310 RX 1550nm Single mode 9 125um 100Base BX D TX 1550 RX 1310nm 1000X Fiber Optical Cables Standard Fiber Type Cable Specification 1000Base SX 850nm Multi mode 50 125um or 62 5 125um 1000Base LX Multi mode 50 125yum or 62 5 125um 1310nm Single mode 9 125um Wiring Distances Standard Fiber Diameter Modal Bandwidth Max Distance micron MHz km meters 62 5 100 220 62 5 200 275 1000Base SX Multi mode 50 400 500 50 500 550 62 5 5 Multi mode 50 4 550 1000Base LK 50 5 Single mode 9 N A ____ 5000 D
17. Industrial Gigabit Switch With 4 Port 802 3at PoE IGS 504HPT IGS 624HPT User s Manual Trademarks Copyright amp PLANET Technology Corp 2013 Contents are subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep the current information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply with the limi
18. Single mode 100Base FX 1000Base SX LX SFP module through DIP switch setting Cabling Each 10 100 1000Base T port uses RJ 45 sockets similar to phone jacks for 17 1 connection of unshielded twisted pair cable UTP The IEEE 802 3 802 3u 802 3ab Fast Gigabit Ethernet standard reguires Category 5 UTP for 100Mbps 100Base TX 10Base T networks can use Cat 3 4 5 or 1000Base T uses 5 5e 6 UTP see table below Maximum distance is 100 meters 328 feet The 100Base FX 1000Base SX LX SFP slot is used as LC connector with optional SFP module Please see table below and know more about the cable s specification 10Base T Cat 3 4 5 2 pair RJ 45 100Base TX Cat 5 UTP 2 pair RJ 45 1000Base T Cat 5 5e 6 UTP 4 pair RJ 45 100Base Fx 50 12S5um or 62 5 125um multi mode T ic Mutti Single mode 9 125yum single mode 1000Base SX 50 125um or 62 5 125um multi mode LX 9 125um single mode LC Multi Single mode Any Ethernet devices like hubs PCs can be connected to the Industrial Gigabit PoE Switch by using straight through wires The four 10 100 1000Mbps ports are auto MDI MDI X and can be used on straight through or crossover cable 2 1 6 1 Installing the SFP transceiver The sections describe how to insert an SFP transceiver into the IGS 624HPT SFP slot The SFP transceivers are hot pluggable and hot swappable You can plug in and out the transceiver to from any SFP port without having to
19. The fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs 29 1 which nearly always improves the overall performances An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using the conventional cabling and adapters Due to the learning function of the Industrial Gigabit PoE Switch the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subseguently used to filter packets whose destination address is on the same segment as the source address This confines network traffic to its respective domain and reduces the overall load on the network The Industrial Gigabit PoE Switch performs Store and Forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 4 5 Auto Negotiation The STP ports on the Industrial Gigabit PoE Switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another network device usually at Power On or Reset This is done by detecting the modes and speeds at the second of both devices that are connected and capable of Both 10Base T and 100Base TX devices can co
20. W 100FX 2 Make sure both sides of the SFP transceivers are with the same media type for example 1000Base SX to 1000Base SX 1000Base LX to 1000Base LX 3 Check whether the fiber optic cable type matches with the SFP transceiver model gt To connect to 1000Base SX SFP transceiver use the Multi mode fiber cable with one side being the male duplex LC connector type gt To connect to 1000Base LX SFP transceiver use the Single mode fiber cable with one side being the male duplex LC connector type Connecting the fiber cable 1 Insert the duplex LC connector on the network cable into the SFP transceiver 2 Connect the other end of the cable to a device switches with SFP installed fiber NIC on a workstation or a media converter 3 Check the LNK ACT LED of the SFP slot on the front of the Industrial Gigabit PoE Switch Ensure that the SFP transceiver is operating correctly 100Base FX Before connecting with switches workstation or media converter please do the following steps 2 1 With 100Base FX Fiber Speed please set the DIP Switch of SFP Port 5 or Port 6 to the ON position OFF ON Port 6 DIP 2 1000X 100FX Port 5 DIP 1 1000X 100FX Make sure both sides of the SFP transceivers are with the same media type or WDM pair for example 100Base FX to 100Base FX 100Base BX20 U to 100Base BX20 D Check whether the fiber optic cable t
21. and use them again to repack the product in case there is a need to return it to us for repair 1 2 How to Use This Manual This Industrial Gigabit PoE Switch User Manual is structured as follows Chapter 2 Installation The chapter explains the feature functionality and the physical installation of the Industrial Gigabit PoE Switch Chapter 3 Application The chapter explains the Industrial Gigabit PoE Switch application Chapter 4 Switch operation The chapter explains the Industrial Gigabit PoE Switch transmit operation 5E Chapter 5 Troubleshooting The chapter explains the troubleshooting of the Industrial Gigabit PoE Switch Chapter 6 Cable Connection Parameters The chapter contains the cable connection parameters of the Industrial Gigabit PoE Switch Appendix A This chapter contains cable information of the Industrial Gigabit PoE Switch 1 3 Product Features Physical Port IGS 504HPT m 5 Port 10 100 1000Base T RJ 45 with IEEE 802 3af 802 3at PoE injector IGS 624HPT m 4 Port 10 100 1000Base T RJ 45 with IEEE 802 3af 802 3at PoE Injector m 2 SFP interfaces 100 1000Base X dual mode DIP switch control Power over Ethernet m Complies with IEEE 802 3af IEEE 802 3at Power over Ethernet Plus End Span PSE m Up to 4 IEEE 802 3af 802 3at devices powered m Supports PoE Power up to 30 8 watts for each PoE ports W Provides DC 52V power over RJ 45 Ethernet cable to PD with Ethernet port m Auto detect
22. de fiber optic cable up to 10 20 30 40 50 70 120 kilometers vary on SFP module 100Base FX 50 125um or 62 5 125um multi mode fiber optic cable up to 2 kilometers 9 125um single mode fiber optic cable up to 20 40 60 kilometers vary on SFP module Switch Specification Switch Processing Scheme Store and Forward Address Table 1K entries Flow Control Back pressure for half duplex IEEE 802 3x Pause Frame for full duplex Switch fabric 10Gbps 12Gbps Throughput packet per second 7 44Mpps 64bytes 8 93Mpps 64bytes Maximum Transmit Unit 9216 bytes Speed Power over Ethernet TP 10 20Mbps 100 200Mbps 2000Mbps SX LX 2000Mbps Full duplex FX 200Mbps Full duplex PoE Standard IEEE 802 3af IEEE 802 3at Power over Ethernet PSE PoE Power Supply Type End Span PoE Power Output Per port 52V DC 275mA Max 15 4 watts IEEE 802 3af Per port 52V DC 535mA Max 30 watts IEEE 802 3at Power Pin Assignment Max number of Class 4 PD 1 2 3 6 Standards Conformance Standards Compliance IEEE 802 3 Ethernet 10Base T IEEE 802 3u Fast Ethernet 100Base TX IEEE 802 3ab Gigabit Ethernet 1000Base T IEEE 802 3z Gigabit Ethernet 1000Base SX LX IEEE 802 3x Full Duplex Flow Control IEEE 802 3at Power over Ethernet Plus IEEE 802 3af Power over Ethernet Regulation Compliance FCC Part 15 Class A CE Stability
23. et Switch Step 4 Use the hook holes at the corners of the wall mount plate to hang the Industrial Gigabit Ethernet Switch on the wall Step 5 To remove the wall mount plate reverse the steps above 26 3 Applications In this paragraph we will describe how to install Industrial Gigabit PoE Switch and the installation points Industrial Operating Environment a 550m 10km 120km 1 1 1 1 1 1 Control Center PoE PTZ 4 Speed Dome qure Ud 10008ase T UTP with PoE IGS 624HPT amp Power Line DC IGS 624HPT Fiber PoE IP Camera Switch Data Center 27 1 Installation Steps Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 128 Unpack the Industrial Gigabit PoE Switch Check the DIN Rail is screwed on the Industrial Gigabit PoE Switch Please refer to DIN Rail Mounting section for DIN Rail installation if the DIN Rail is not screwed on the Industrial switch If you want to wall mount the Industrial Gigabit Ethernet Switch please refer to Wall Mount Plate Mounting section for wall mount plate installation To hang the Industrial Gigabit PoE Switch on the DIN Rail track or wall please refer to the Mounting Installation section Power on the Industrial Gigabit PoE Switch Please refer to the Wiring of the Power Inputs section for power input The power LED on the Industrial Gigabit
24. ion of IEEE 802 3af at eguipments and protects devices from being damaged by incorrect installation m Remote power feeding up to 100m Layer 2 Features W Supports Auto negotiation and 10 100Mbps half full duplex and 1000Mbps full duplex mode m Prevents packet loss with back pressure Half Duplex and IEEE 802 3x PAUSE frame flow control Full Duplex m Automatic address learning and address aging Industrial Case Installation m IP30 aluminum metal case protection m DIN Rail and Wall Mount Design m 48V DC redundant power with polarity reverse protect function and connective removable terminal block for master and slave power m Supports EFT protection 6000 VDC for power line m Supports 6000 VDC Ethernet ESD protection m 40 to 75 degrees C operating temperature Fiber Port Redundancy IGS 624HPT Only W Dual SFP Ports Auto Link Redundant Mode Support W Link status auto detect and redundant on Dual ports with same connector type W Only Primary Port is active at a time the Backup Port is blocked W While Primary Port link fail occurrences the traffic swaps to Backup Port automatically W Once the Primary Port status backs to link up the traffic swaps from Backup Port to Primary Port 1 4 Product Specifications Model IGS 504HPT IGS 624HPT Hardware Specification 4 x 10 100 1000Base T RJ 45 TP Auto MDI MDI X Auto negotiation 2 x SFP interfaces Support SFP mini GBIC Slots 1000Base SX LX and 100Base FX SFP
25. m 1310nm 0 60 C Single MGB LA40 1000 WDM LC Mode 40km 1310nm 1550nm 0 60 C Single MGB LB40 1000 WDM LC Mode 40km 1550nm 1310nm 0 60 C Single MGB LA60 1000 WDM LC Moda 60km 1310nm 1550nm 0 60 C Single MGB LB60 1000 WDM LC Mode 60km 1550nm 1310nm 0 60 C Single MGB TLA10 1000 WDM LC Mode 10km 1310nm 1550nm 40 75 C Single MGB TLB10 1000 WDM LC Mode 10km 1550nm 1310nm 40 75 C Single MGB TLA20 1000 WDM LC Mode 20km 1310nm 1550nm 40 75 C Single MGB TLB20 1000 WDM LC Mode 20km 1550nm 1310nm 40 75 C Single MGB TLA40 1000 WDM LC Mode 40km 1310nm 1550nm 40 75 C 120 MGB TLB40 1000 WDM LC mia 40km 1550nm 1310nm 40 75 C Single MGB TLA60 1000 WDM LC p 60km 1310nm 1550nm 40 75 C Single MGB TLB60 1000 WDM LC p 60km 1550nm 1310nm 40 75 C It is recommended to use PLANET SFP transceivers on the Indus trial Gigabit PoE Switch If you insert an SFP transceiver that is not in the supported list the Industrial Gigabit PoE Switch might not recognize it 1000Base SX LX Before connecting with switches workstation or media converter please do the following steps 1 With 1000Base X Fiber Speed please set the DIP Switch of SFP Port 5 or Port 6 to the OFF position OFF ON Port 6 DIP 2 1000X 100FX Port 5 DIP 1 1000X w
26. nm 1550nm 40 75 C Single MFB TFB40 100 WDM LC Mode 40km 1550nm 1310nm 40 75 C Gigabit Ethernet Transceiver 1000Base X SFP Speed Connector c Wavelength Operating Model Mbps Interface Fiber Mode Distance Rh Top MGB GT 1000 Copper 100m zx 0 60 C MGB SX 1000 LC Multi Mode 550m 850nm 0 60 C MGB SX2 1000 LC Multi Mode 2km 1310nm 0 60 C MGB LX 1000 LC Single Mode 10km 1310nm 0 60 C MGB L30 1000 LC Single Mode 30km 1310nm 0 60 C MGB L40 1000 LC Single Mode 40km 1550nm 0 60 C 19 1 MGB L50 1000 LC Single Mode 50km 1550nm 0 60 C MGB L70 1000 LC Single Mode 70km 1550nm 0 60 C MGB L120 1000 LC Single Mode 120km 1550nm 0 60 C MGB TSX 1000 LC Multi Mode 550m 850nm 40 75 C MGB TLX 1000 LC Single Mode 10km 1310nm 40 75 C MGB TL30 1000 LC Single Mode 30km 1310nm 40 75 C MGB TL50 1000 LC Single Mode 50km 1550nm 40 75 C Gigabit Ethernet Transceiver 1000Base BX Single Fiber Bi Directional SFP Speed Connector Fiber _ Wavelength Wavelength Operating TS Mbps Interface Mode Distance TX RX Temp MGB LA10 1000 WDM LC ae 10km 1310nm 1550nm 0 60 C Single MGB LB10 1000 WDM LC Mode 10km 1550nm 1310nm 0 60 C Single MGB LA20 1000 WDM LC Mode 20km 1310nm 1550nm 0 60 C Single MGB LB20 1000 WDM LC Mode 20km 1550n
27. nnect with the port in either Half or Full Duplex mode 1000Base T can be only connected in Full duplex mode 5 Troubleshooting This chapter contains information to help you solve issues If the Industrial Gigabit PoE Switch is not functioning properly make sure the Industrial Gigabit PoE Switch was set up according to instructions in this manual The Link LED does not light up Solution Check the cable connection and also try to swap one new cable Performance is bad Solution Check the speed duplex mode of the partner device The Industrial Gigabit PoE Switch is run at Auto negotiation mode and if the partner is set to half duplex then the performance will be poor 1000Base T port link LED lights up but the traffic is irregular Solution Check that the attached device is not set to full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why the Industrial Gigabit PoE Switch doesn t connect to the network Solution Check per port LED on the Industrial Gigabit PoE Switch Try another port on the Industrial Gigabit PoE Switch Make sure the cable is installed properly Make sure the cable is the right type Turn off the power After a while turn on the power again Why after my PoE PD device is connected to IGS 504HPT IGS 624HPT it cannot power on Solution Please check the cable type of the connection from IGS 5
28. strial 2 1 7 Redundancy Overview The IGS 624HPT Industrial Gigabit PoE Switch provides rapid fiber redundancy of link for highly critical Ethernet applications The redundant mode supports auto recover function If the destination port of a packet is link down it forwards the packet to the other port of the backup pair The following figure shows the redundant function Redundancy Redundancy Traffic is changed from Primary Port to Backup Port lt Primary Port gt Link Status Up Traffic Flow Forwarding lt Backup Port gt Link Status Down Traffic Flow Blocking lt Primary Port gt Link Status Down Traffic Flow N A lt Backup Port gt Link Status Up Traffic Flow Forwarding Figure 2 5 Redundancy Behavior Topology Link status auto detect and redundant on Dual ports with same connector type Only Primary Port is active at a time the Backup Port is blocked e When Primary Port link failure occurs the traffic swaps to Backup Port automati cally Once the Primary Port status is back to link up the traffic will swap from Backup Port to Primary Port 23 4 2 2 Mounting Installation This section describes how to install the Industrial Gigabit PoE Switch and make connections to it Please read the following topics and perform the procedures in the order being presented In the installation steps below this Manual
29. ts for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a K result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste they should be collected separately Revision PLANET Industrial Gigabit Switch with 4 port 802 3at PoE User s Manual For Model IGS 504HPT IGS 624HPT Revision 1 0 APRIL 2013 Part No EM IGS 504HPT_624HPT_v1 0 2350 AH0600 000 Table Of Contents T STntrOducE 0 ien ties tise uii y Di eden nauta pae Blin CAT Mf FT 1 1
30. uture packets 4 3 Forwarding amp Filtering When one packet comes from some ports of the Industrial Gigabit PoE Switch it will also check the destination address besides the source address learning The Industrial Gigabit PoE Switch will look up the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at a different port from this packet that comes in the Industrial Gigabit PoE Switch will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet that comes in then this packet will be filtered thereby increasing the network throughput and availability 4 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Industrial Gigabit PoE Switch stores the incoming frame in an internal buffer and does the complete error checking before transmission Therefore no error packets occurs It is the best choice when a network needs efficiency and stability The Industrial Gigabit PoE Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if reguired
31. wer over Ethernet Plus PoE that combine up to 30 watt power output and data per port over one Cat 5E 6 Ethernet cable With a total of up to 120 watts of PoE output capability the IGS 504HPT and IGS 624HPT are designed specifically to satisfy the growing demand of higher power consuming network PDs powered devices such as PTZ Pan Tilt amp Zoom speed dome network cameras multi channel 802 11a b g n wireless LAN access points and other PoE network devices by providing double PoE power rather than the current conventional 802 3af PoE Environmentally Hardened Design The IGS 504HPT and IGS 624HPT are eguipped with rugged IP30 metal case for easy deployment in heavy Industrial demanding environments With IP30 metal case protection the IGS 504HPT and IGS 624HPT provide a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets Being able to operate in the temperature range from 40 to 75 degrees C the IGS 504HPT and IGS 624HPT can be placed in almost any difficult environment The IGS 504HPT and IGS 624HPT allows either DIN rail or wall mounting for efficient use of cabinet space Adjustable 6 Port Switch Mode or 4 2 Fiber Redundant Mode Via the built in DIP switch the IGS 624HPT can be configured as 6 Port Ethernet switch or 4 2 fiber redundant mode With the 6 port switch mode the IGS 624HPT can operate in Store
32. ype matches with the SFP transceiver model gt To connect to MFB FX SFP transceiver use the multi mode fiber cable with one side being the male duplex LC connector type gt To connect to MFB F20 F40 F60 FA20 FB20 SFP transceiver use the single mode fiber cable with one side being the male duplex LC connector type Connecting the fiber cable 1 2 Insert the duplex LC connector on the network cable into the SFP transceiver Connect the other end of the cable to a device switches with SFP installed to fiber NIC on a workstation or a media converter Check the LNK ACT LED of the SFP slot of the switch converter Ensure that the SFP transceiver is operating correctly 2 1 6 2 Remove the Transceiver Module 1 Make sure there is no network activity by consulting or checking with the network administrator Or through the management interface of the switch converter if available to disable the port in advance 2 Remove the Fiber Optic Cable gently 3 Turn the latch of the MGB MFB module to a horizontal position 122 Pull out the module gently through the latch t ISIN MGB MFB Series Transceiver wT 45 1 Figure 2 4 Pulling out from the transceiver Gigabit Ethernet Switch Never pull out the module without pulling the latch or the push bolts on the module Directly pulling out the module with violence could damage the module and the SFP module slot of the Indu
Download Pdf Manuals
Related Search
IGS 504HPT UserManual