Patron E15 ver. 4-03 - 4
Contents
1. carefully and Patron Products shall not be respon sible for damage in transit When returning parts the owner must provide the model number of the product and the nature of difficulty being experienced This warranty does not oblige Patron Products to bear the cost of labour in replacing any assembly unit or component or part thereof nor does the company assume any liability for secondary charges expenses of removal or installing freight or damages There will be charges rendered for product repair after our warranty period has expired Proof of purchase in cluding date must accompany request for in warranty service Patron E1 5 4 03 3 3 OPERATION REVIEW AND UNDERSTAND ALL WARNINGS IN THIS MANUAL THEY ARE ESSENTIAL FOR SAFE USE OF THE HEATER FOLLOW ALL LOCAL CODES This heater is for use on 120 volts Grounding pin The cord has a plug as shown in the figure The type of outlet is a 120 volt grounding outlet When properly installed it pro vides a ground connection through the cord to the heater to protect the operator from electric shock TO START HEATING 1 Place the heater on a stable and level surface Make sure that no explosive or combustible fumes or dust are present MINIMUM CLEARANCES FROM COMBUSTIBLE MATERIALS OUTLET 6 feet SIDES 1 foot TOP 2 feet REAR 2 feet FLOOR COMBUSTIBLE 2 Connect power cord of heater into 120 V 60 Hz power source See para graph Technical2. limit switch disjoncteur de surchauffe terminal block bloc terminal grounding lug bloc terre power cord amp plug fil electrique amp fiche Patron E1 5 4 03 PATRON PRODUCTS INC USA 60 Clyde Avenue Suite 4 Buffalo NY 14215 Canada 12 110 Ironside Crescent Scarborough Ontario M1X 1M2
3. CHNICAL SPECIFICATIONS MODEL PATRON E1 5 Heat output BTU hr 5 100 1 500 W Air flow CFM 116 200 m h Electric connection Vac Hz 120 60 single phase Amperage draw A 12 5 Power cord 3x16 AWG Plug NEMA 5 15P Extension cord min 3x12 AWG Ambient thermostat temp range 32 100 F 0 40 C Length inches 14 6 370 mm Width inches 7 9 200 mm Height inches 12 2 310 mm Weight lbs 13 7 6 2 kg Patron E1 5 4 03 7 EXPLODED VIEW handle poignee 80102 outer mantle carcasse 4001600 overheat limit switch disjoncteur de surchauffe 21200 inner mantle cheminee interieure 40015 heating element element 42256 front panel panneau avant 40014 bottom plate plaque de fond 40012 fan blade pales du ventilateur 16040 hub moyeu 17907 fan motor motor du ventilateur 14040 rear panel panneau arriere 4001100 power cord amp plug fil electrique amp fiche 30330 room thermostat knob thermostat ambiant 20220 20576 strain reliever retenue de fil 36910 wire bushing douille 36809 terminal block Patron E1 5 4 03 bloc terminal 8 WIRING DIAGRAM 2 Patron E1 5 Code fan motor motor du ventilateur heating element element room thermostat thermostat ambiant overheat
4. USER S MANUAL FOR PATRON E1 5 ELECTRIC FAN HEATER 4 03 IMPORTANT READ AND UNDERSTAND THIS MANUAL BEFORE ASSEMBLING STARTING OR SERVICING THE HEATER IMPROPER USE OF HEATER CAN CAUSE SERIOUS INJURY KEEP THIS MANUAL FOR FUTURE REFERENCE FOR PROFESSIONAL USE ONLY 11 12 13 14 15 READ ALL INSTRUCTIONS BEFORE USING THIS HEATER This heater is hot when in use To avoid burns do not let bare skin touch hot sur faces Use handle when moving this heater Keep combustible materials at least 6 feet 2 meter from the front of the heater and keep them away from sides and rear Extreme caution is necessary when the heater is used near children or invalids and whenever the heater is left unattended Always unplug the heater when not in use Do not operate any heater with a damaged cord or plug or after the heater malfunc tions has been dropped or damaged in any manner Return heater to authorized service facility for examination electrical or mechanical adjustment or repair Do not expose to rain water spray or dripping water This heater is not intended for use in bathrooms laundry areas and similar indoor locations Never locate the heater where it may fall into a bathtub or other liquid con tainer Do not run cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over To disconnect heater turn controls to off
5. n by the fan Keep the heater clean of dust at any time Dust may cause fire when heated Make sure that the fan blades may rotate unobstructed at all times Do not block air intakes or exhaust in any manner 2 LIMITED WARRANTY PATRON heater products are professional construction heaters They are warranted for twenty four 24 months from original date of purchase The warranty does not cover products modified outside our factory damage or failure caused by acts of God abuse misuse use on other than rated voltage abnormal usage faulty or improper installation failure to provide recommended maintenance or any repairs other than those provided by an authorized PATRON service THERE ARE NO OBLIGATIONS OR LIABILITIES ON THE PART OF PATRON PROD UCTS INC FOR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNEC TION WITH THE USE OR PERFORMANCE OF THE PRODUCT OR OTHER INDIRECT DAMAGES WITH RESPECT TO LOSS OF PROPERTY REVENUES OR PROFIT OR COST OF REMOVAL INSTALLATION OR REINSTALLATION THIS WARRANTY CONSTITUTES THE EXCLUSIVE REMEDY OF ANY PURCHASER OF EQUIPMENT SOLD BY THE MANUFACTURER AND ITS DEALERS AND DIS TRIBUTORS AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED During the warranty period Patron Products will at its sole option repair or replace any defective parts or products returned freight prepaid to Patron Products or such other lo cation as Patron Products may designate Returned products must be packaged
6. specifications in this manual for correct amperage rating 3 Set the room thermostat from heat off position to a temperature above the ambient room temperature by turning the knob Note The heater will start heating only if the thermostat calls for heat meaning that it is set to higher than prevailing ambient temperature 4 The heater will now operate automatically controlled by the thermostats TO STOP HEATING 1 Turn the room thermostat into position heat off 2 Let the fan cooldown heater for 2 3 minutes 3 Disconnect the power supply plug NOTE THE HEATER IS EQUIPPED WITH AN OVERHEAT LIMIT SWITCH WHICH MAY CAUSE THE HEATER TO STOP CHECK AND REMOVE THE CAUSE FOR OVERHEATING BEFORE RE STARTING Patron E1 5 4 03 4 4 MAINTENANCE WARNING NEVER SERVICE THE HEATER WHILE IT IS PLUGGED IN RUNNING OR HOT SEVERE BODILY INJURE OR ELECTRIC SHOCK MAY OCCUR ONLY QUALIFIED PERSONS ARE ALLOWED TO OPEN HEATER FOR SER VICE NO USER SERVICEABLE PARTS INSIDE Keep heater clean Use pressurized air to blow fan blades clean Note Use moderate pressure to avoid damage to fan blades Inspect heater before and after each use The fan motor is sealed and has permanently lubricated bearings 5 STORAGE When not in use the heater must be disconnected from power source cleaned of dust and stored in a dry place The power supply cord should be loosely wound around the handle of the heater 6 TE
7. then remove plug from outlet Connect to properly grounded outlets only Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater To prevent a possible fire do not block air intakes or exhaust in any manner Do not use on soft surfaces where openings may become blocked A heater has hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored Do not point to flammable materials Use heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Avoid use of an extension cord because it may overheat and cause a risk of fire However if you have to use an extension cord the cord shall be a three 3 wire grounded cord check minimum size from specifications Patron E1 5 4 03 2 1 GENERAL INFORMATION FOR USER Patron electric heaters are designed for professional use The heat is generated in sealed heating elements inside the inner mantle of the heater Heated air is then distributed by an electric motor driven fan blowing air through the heater Although effectively cooled by the fan the heating elements have high surface temperatures That is why combustible materials must be kept at a safe distance from the heater and care must be taken that no combustible particles enter the heater with the air sucked i
Download Pdf Manuals
Related Search