SVP305 SIP/IAX IP phone User Manual - stephen
Contents
1. at O Busy No Answer Always Er Phone Humber Addr Port 5060 20 __ No answer reem EN User configure the value add service such as hotline call forward call transfer 3 way conference call etc in this page Hotline configure hotline number SVP305 immediately dials this number after book oft if it is set Call Forward Please refer to Value add service for detail No Disturb DND do not disturb enable this option to refuse any calls Ban Outgoing Enable this to ban outgoing calls Enable Call Transfer Please refer to Value add service for detail Enable Three Way Call Please refer to Value add service for detail Enable Call Waiting Enable disable Call Waiting Accept Any Call If this option is disable SVP305 refuse the incoming call when the called number is different from SVP305 s phone number No Answer Time no answer call forward time setting Auto Answer Enable disable auto answer function Enable Voice Record Enable disable answering machine function Please refer to Record Function for detail User defined Voice Use customized greeting message Incoming Record Playing simultaneously play the message when recording Black List incoming call in these phone numbers will be refused Limit List outgoing calls with these phone numbers will be refused www stephen tele com 2 5 8 MMI Filter MMI Filter 3 Start IP to be deleted MMI filter is used to make access2. Add UDP mapping rule udp entry ip x x x x lanport xxx wanport xxx Delete UDP mapping rule NO udp entry ip x x x x lanport xxx wanport xxx Show NAT info SNOW gt Netservice path lt config netservice gt Set DNS address ANS ip X X X x _domain xxx Example lt config netservice gt dns ip 202 112 10 36 _domain voip com Set alternate DNS address alterdns ip x x x x _domain xxx Set hostname hostname xxx Set http access port http port xxx www stephen tele com Show http access setting http port Set telnet access port telnet port xxx Show telnet access port telnet port Set RTP initial port and quantity media port startport xxx number xxxx Example lt config netservice gt media port startport 10000 number 200 Add route rule route gateway X x x x addr x x x x mask X X X X Example Arcihfone lt config netservice gt route gateway 202 112 10 1 addr 202 112 210 1 mask 255 255 255 0 Delete route rule no route gateway X x x x addr x x x x mask X X X X Show route info route Show netservice info SNOW gt Dial peer settings path lt config pbook gt disable enable calling through GK and proxy no JenableGKandProxy Add number IP bond entry entry number xxx ip x x x x protocol xxx Example lt config pbook gt entry number 100 ip 202 112 20 100 protocol sip Add number IP bond and add prefix to the dial number entry num
3. MENU seen 32 Tone ONS ONC ee 34 4 1 INLLOGUCE EE 34 42 NOD Al COP UII EE 35 Tree Structure nee Teer 36 NEIWOIK DIAGNOSIS een 45 Restore to factory detault ccc ccccssssscccccessssceecceesssseeeeeeesessseeeceeesssaeeeeeeens 45 www stephen tele com 8 de Ree EE MOG E 46 IFA ae crs accessed eet ce cee acces eee ee ae cece 47 9 1 How many servers may SVP305 register simultaneously ee 47 9 2 Why the settings vanish after reboot ccc ccccsssccceessseccessseeceessseeceesseeceeenseees 47 93 MOWIOUSETINE Glial TNC 7 csc c csasscosssavsvassaanzenesadenansnadacorasadacsagnadsesaqsoisaagoatnesaaesievseasaine 47 9 4 How to use speed ial funchon 48 9 5 How to configure digital map 48 9 6 How to use Call Forward Call Transfer and 3 way Conference calls 48 9 7 How to use the record Tunchon 50 9 8 Howto use set the IP type via keypad 0 ccc cccsssecceessseccessseeceessseeceessseeeeeseees 51 www stephen tele com onma 1 SVP305 Features 1 1 Appearance 1 2 Interface Power Output Power 12VDC 500mA WAN RJ45 port LAN RJ45 port LA Electricity characteristic Speciality of electric output the 12V 500mA DC The network connects 2 RJ45 connect a WAN a LAN 1 4 Software Support two sip accounts at the same time Redundancies server support NAT Firewall DHCP client and server Support PPPoE used for ADSL cable modem connecting Support major G7 xxx CODEC www st
4. Num www stephen tele com Transfer IP Port End With Fixed Length Dial Rule Switch Length SIP Reg Status Public Reg Private Reg Detect server Dtmf mode Interval time Swap server RFC version Signal Port Stun Switch Addr Port Expire Time DSP Codec Handdown time Dtmf Volume Input volume Output Volume Other Setting Syslog Switch Server IP Server Port 4 System 1 Save 2 Reboot 3 Set Default www stephen tele com 4 Telnet Console 4 1 Introduce 4 1 1 Basic structure User may use telnet command to access and manage IP phone SVP305 adopts tree structure for telnet Every node contains its sub nodes or local command User can type help or whenever to see sub nodes and all local command under current node Besides local command there are some global commands can be used in each node 4 1 2 Basic command Logout exit telnet mode Write save current settings Type sub nodes name in current node to switch to sub node Type or exit in current node to return to parent node Type help or can see all sub nodes and all local command under current node every help item has comments such as lt command gt or lt node gt to distinguish sub nodes and local command Type help or in command can see all parameters using in this command When typing node name or command user no need to key the full name use TAB
5. button will make it more efficient There are two types in command parameters optional and required required parameter use H 9 DI 3 as prefix and optional use _ as prefix User may type complementarily H 9 17 39 or then press TAB button for www stephen tele com 4 2 Global Command Global command is available under all nodes SVP305 support following commands Show sub nodes and local command 2 help who www stephen tele com 5 Tree Structure 5 1 1 account path lt account gt stop start Syslog syslog no start Configure Syslog server address and port syslog server ip x x x x _ port Xxx Example lt config account syslog gt server ip 202 112 20 10 Show syslog settings syslog show Show all account settings show 5 1 2 config gt accesslist firewall config path lt config accesslist gt add firewall rule entry O xxx P D xxx proto xxx srcaddr x x x x srcmask x x x x desaddr x x x x desmask x x x x portrange xxx portnum xxx Example lt config accesslist gt entry l O input P D deny proto udp straddr 202 112 10 1 srcmask 255 255 255 0 desaddr 210 25 132 1 desmask 255 255 255 0 portrange neq portnum 5060 delete firewall rule no entry I O xxx index xxx Example lt config accesslist gt no entry JC input index 1 Show firewall settings Show disable enable input filter no in access disable enable output
6. config mode _ confirm or enter sub menu yp Dis mode volume up Max 9 Down Calling mode volume down Min 1 Calling mode Delete digits Out call Idle mode Outgoing call menu Idle mode Incoming call menu Recor P mode Enter record menu usage refer FAQ Pook fee mode Enter Phone book set up Calling mode Digits 0 9 ei quickly to switch between numeric or alphabetic Mute In call Record Pbook Calling mode Use in 3 way conference call configmode Leg as In the ip address setting Calling mode Use as end key of dialing or the dial number Hold Calling mode Hold detail refer value add service FWD Calingmode Transfer detail refer value add service Redial Calling mode Redial key Send Calling mode call key No 1 No 9 Idle mode Speed dial key www stephen tele com CHIMA a Stephen Technologies Co Limited 3 2 Keypad Menu User may use SET Menu ok Exit Vol Vol to config SVP305 detail setting Press Menu ok to enter config mode and the default password is 123 d Below list the keypad menu of SVP305 SVP305 Keypad Menu Network LAN Bridge Mode Netmask DHCP Server NAT Switch FTPalg IPSec alg PPTPalg WAN Status Static Net 1 IP 2 NetMask 3 Gateway 4 DNS 5 DNS2 PPPoE User name Password QoS Call Feature Phone number Level 4 Public SIP Private SIP Current ADD DEL Black List Current ADD DEL Call Forward Condition Limit List Transfer
7. customizes greeting voice for answering machine Notice SVP305 supports three message maximum each message can be 90 seconds Answering will be deactivated if the message numbers is 3 Record local message User may use local message to leave message to other local users Please refer the Record button function as below Record Function Levelt Level2 Description Received New New message info Old message info Record Enable disable answering machine Playing Enable disable Incoming Record Playing Local Play Play local message Rec Record local message User define Switch Enable disable customize greeting message Play Play customize greeting message Rec Record customize greeting message www stephen tele com 9 8 How to use set the IP type via keypad In the idle mode user may us the keypad to set the IP type as the below procedure Keep pressing the button for changing to static mode Keep pressing the button 2 for changing to DHCP mode Keep pressing the button 3 for changing to PPPoE mode Copyright Notice No part of this document may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of Stephen Technologies Co Limited Disclaimer Notice No license is granted implied or otherwise under any patent or patent rights of Stephe
8. gt dhcp server gt dial rule path lt show gt show digital map info Example lt show gt dial rule gt interface path lt show gt show LAN info Example lt show gt interface fastethernet lan show WAN info Example lt show gt interface fastethernet wan gt ip path lt show gt show arp table info Example lt show gt ip arp Show DNS server info Example lt show gt ip dns Show neistate info Example lt show gt ip netstat Show route info Example lt show gt ip route Show icmp packets Stat Example lt show gt ip icmp Show igmp packets Stat Example lt show gt ip igmp Show ip packets Stat Example lt show gt ip ip Show RTP packets Stat Example lt show gt ip rtp Show TCP packets Stat Example lt show gt ip tcp Show UDP packets Stat Example lt show gt ip udp gt memory path lt show gt show IP phone memory Example lt show gt memory www stephen tele com Stephen Technologies Co Limited D gt nat path lt show gt show NAT information Example lt show gt nat gt port path lt show gt show caller ID info Example lt show gt port callerID show dsp info Example lt show gt port dsp show hotline info Example lt show gt port hotline show black list info Example lt show gt port in limit show outgoing limit info Example lt show gt port out limit show current phone number Example lt show gt port num
9. rule out _access enable enable out _access rule Input Output specify current adding rule is input rule or output rule Deny Permit specify current adding rule is deny rule or permit rule Protocol Type protocol using in this rule TCP IP ICMP UDP Port Range port range if this rule Src Addr source address Can be single IP address or network address Dest Addr destination address Can be IP address or network address Src Mask source address mask Indicate the source is dedicate IP if set to 255 255 255 255 Otherwise is network ID Des Mask Destination address mask Indicate the source is dedicate IP if set to 255 255 255 255 Otherwise is network ID www stephen tele com 2 5 5 QoS settings IP Phone 02 1p Configuration I VLAN Enable WLAN ID SVP305 IP phone implement QoS based on 802 1p The QoS is used to mark the network communication priority in the data link MAC sub layer SVP305 will sorted the packets using the QoS and sends it to the destination VLAN Enable If enable the VLAN service the second layer will realize separate voice signal and data transmission To realize separate voice and data transmission by dispose for IP precedence of ToS area of voice transmission To reach upper layer switch or router have priority to transfer voice transmission The prerequisite is the upper layer switch or router have to identify ToS area VLAN ID Dispose VLAN ID is add a Tag header after realize enable the VLAN f
10. signal port Set proxy server _ password xxx Example lt config sip server gt proxy ip 210 25 23 22 _port 5060 _user aaa _password 123456 Set register server info _password Xxx Set alter proxy info _ password xxx no service xxx Show noJentry addr x x x x mask x Xx X X 112 10 1 mask 255 255 255 0 no include no register no detect server default domain xxx dtmf mode xxx interval time xxx Ffc version Xxx no Swap server number password number xxx password xxx Signalport xxx server proxy ip X X X X _port xxx _user Xxx server register ip X X X X _ port Xxx user XXX alter server proxy ip X X X X _port Xxx _USEr XXX www stephen tele com a Stephen Technologies Co Limited Set alter server info alter server register ip x x x x _ port xxx _user Xxx _ password xxx disable enable stun server stun no enable Set stun detecting interval time stun interval time xxx Set stun server ip and port Stun IP X X X X port xxx Show current sip info show gt User management path lt config user gt Change user right access USer XXX ACCESS XXX Example lt config user gt access user aaa access Change user password password user Xxx Add new user entry user xxx acceSs XXX Example lt config user gt entry user abc access 7 Delete user entry no entry user xxx Show current s
11. 45 63 75 95 192 169 10 2 00 0f 11 a0 26 07 HTTP Port configure HTTP transfer port default is 80 User may change this port to enhance systems security When this port is changed please use htt Xxx XXX XXX XXX XXxx to reconnect Telnet Port configure telnet transfer port default is 23 RTP Initial Port RTP initial port RTP Port Quantity Maximum RTP port quantity default is 200 Notice Settings in this page won t take effect unless save and reboot the device lf you need to change telnet port or HTTP port please use the port greater than 1024 because ports under 1024 is system remain ports HTTP service if HTTP is set to 0 www stephen tele com 2 5 4 Firewall settings Firewall Configuration BEE Apply Firewall Input Rule Table Firewall Output Rule Table InpubiOutput Input el DenyPermit Deny Protocol Type UDP w Port Range more than ei Beete 1 O DOO Pesos Firewall setting page User may set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet input rule or prevent unauthorized private network devices to access the internet Access list support two type limits input_access limit or output_access limit Each type support 10 items maximum SVP305 firewall filter is base WAN port So the source address or input destination address should be WAN port IP address Configuration in_access enable enable in_access
12. CHIMA a S Stephen Technologies Co Limited SVP305 SIP IAX IP phone User Manual www stephen tele com N O O1 FS UGS a E E E E EE E 4 1 1 ele EL ie EE 4 1 tat Te E 4 1 3 Electricity characteristic eee ccccssssccceeesssceeceeessseeeceeesssseeceeessseeceeeesssseeceeessseeeeeeens 4 4 2 O ee E 4 1 5 Standard and Protocols 0 0 0 ec cecssccessseceesscceesseccessecceeseecesseccesseceesseeeesseeeeseeeesseeeeeses 5 1 6 2 Kompliant Standard 5 1 7 Operating Beet E E 5 19 PA I E 5 19 MOS UA EMI E 6 VVC COMMUN ATOM E 7 2 1 Access Web setting Page ccssccssssseccsssssecesssseccssseeecsssasecessesecesesseeeessaseceseaaeeesns 7 EE e EE 8 23 Ee E 9 2 3 1 WAGON 0 EE 9 2256 EAI GOW E E E E E E 11 2a VO E 12 2 4 1 A I e DE 12 eA AD e ale 13 725 ME en e 14 2 5 1 DACE E 14 GE RE 15 25 3 e 16 294 Firewall SETI ING E 17 255 DO SOI CC 18 256 Advance SIP setings E 19 2 5 7 Call Service Settings eee ccssscccsssecessseceesseceesseecesseeeesssecessseeeeseeeesseeens 22 EG ER WE 23 29 AdO ONI EE 24 26 Dal PERL SUS nee ers oeaiobat A ATA 25 2 7 GontgManage eee ececccccssccessscceessccceseccesseceesseecesseeceeseeccesseceesseecesseeceesseceeseeeeesseeeenes 26 209 ee 27 29 E En E EE 29 2 9 1 Account Manage 29 2 9 2 PRONG OOM soara 29 2 93 SVSs100 E el e KE 29 SE AL Gas Rn OO A EAE 30 PA S KE FCI O 6 RE 30 Use keypad configure SVP305 IP Phone wu ccc ccccsscccceessseeceeesseeeeeesnaeees 31 IT Kya TUNG ON een ee 31 32 ee
13. ay function User may use below setting to add a new lease table Lease Table Name Lease table name Lease Time DHCP server lease time Start IP Start IP of lease table End IP End IP of lease table Network device connecting to the SVP305 LAN port can dynamic obtain the IP in the range between start IP and end IP Netmask Netmask of lease table Gateway Default gateway of lease table DNS default DNS server of lease table Notice This setting won t take effect unless you save the config and reboot the device www stephen tele com 2 5 2 NAT IP Phone NAT Configuration IPSec ALG FTP ALG Transfer Type Outside Port DMZ Table Advance NAT setting Maximum 10 items for TCP and UDP port mapping IPSec ALG Enable Disable IPSec ALG FTP ALG Enable Disable FTP ALG PPTP ALG Enable Disable PPTP ALG Transfer Type Transfer type using port mapping Inside IP LAN device IP for port mapping Inside Port LAN device port for port mapping Outside Port WAN port for port mapping Click Add to add new port mapping item and Delete to delete current port mapping item www stephen tele com a b Stephen Technologies Co Limited 2 5 3 Net Service Net Service FTF Initial Port 10000 RTP Port Guantity 200 H modify HTTP or Telnet port you d better set t more than 1024 then save and restart DHCP Lease Table Leased IP Address Client Hardware Address 192 168 10 4 00 09 45 52 06 3f 192 169 10 3 00 09
14. ber show current port status Example lt show gt port status gt PPPoE path lt show gt show PPPoE info Example lt show gt pppoe gt qos path lt show gt show QoS table info Example lt show gt qos gt sip path lt show gt show sip info Example lt show gt sip gt udptunnel path lt show gt show UDP tunnel info Example lt show gt udptunnel gt uptime path lt show gt show running time Example lt show gt uptime www stephen tele com Stephen Technologies Co Limited gt version path lt show gt show IP phone version Example lt show gt version 5 1 8 telnet and logout Usage telnet target port Login xxx Password xxx logout 5 1 9 timesettings path lt time gt manualset year xxx month xxx day xxx hour xxx minute xxx Second xxx Example lt time gt manulset year 2004 month 10 day 1 hour 8 minitute 30 second 0 disable Jenable SNTP server sntp no start Set SNTP IP address sntp server X X X X set SNTP server timeout sntp timeout xxx Set timezone 12 12 Sntp ZONE Xxx Show SNTP info sntp show Show current time print 5 1 10 tracert trace network path info usage tracert host Example tracert HYPERLINK http www google com www google com 5 1 11 update IP phone usage update ftp user xxx password xxx ip x x x x file xxx update tftp ip x x x x file xxx Example updat
15. ber xxx ip x x x x protocol xxx _ add xxx Example lt config pbook gt entry number 100 ip 202 112 20 100 protocol sip _add 123 dial 100 and will send 123100 according this rule Add number IP bond and replace the destination with another number entry number xxx ip x x x x protocol xxx _ all xxx Example lt config pbook gt entry number 100 ip 202 112 20 100 protocol sip all 123 user dial 100 and gateway will sent 100 instead Add number IP bond and delete the prefix of the destination number entry number xxx ip x x x x protocol xxx _ del xxx Example lt config pbook gt entry number 1234 ip 202 112 20 100 protocol sip del 2 dial 1234 will send 34 instead Add number IP bond and replace the prefix with another number entry number xxx ip X X X X protocol xxx _ rep xxx _length xxx Example lt config pbook gt entry number 1234 ip 202 112 20 100 protocol sip _rep 567 _length 2 dial 1234 will send 56734 Delete dial peer entry no entry number xxx Show current dial peer rules sShow Set default voip protocol default protocol xxx gt Port settings path lt config port gt amp lt config port X gt set accecp relay mode accept relay xxx set callerid mode Callerid xxx disable callerid no callerid config call forward callforward conditon xxx number xxx ip xxx port xxx protocol XXX Example lt config port 0 gt callforward condition busy
16. dit the configure file version to lt lt VOIP CONFIG FILE gt gt Version 1 0007 lt GLOBLE CONFIG MODULE gt ConfFile Version 7 www stephen tele com 2 9 System Manage 2 9 1 Account Manage Account Configuration Se e Ladd _ Delete moait J guest e Set web access account or keypad password of SVP305 2 9 2 Phone Book User may set contacts in this page and the contacts will be saved in the memory Then using the Pbook Vol Vol Menu OK and Exit keys to choose your friend in the contacts and then press to call out 2 9 3 Syslog Config www stephen tele com 2 9 4 Time Set IP Phone Time Configuration SHTP Timeset 207 Ap 120 7100 fShT 08 00ibeijing Hong Kong Urumai wi O Daylight Server type the ip address of time server Timezone select correct time zone in list box Timeout longest response time for SNTP Manual Timeset The time setting Daylight Daylight saving time 2 9 5 Reboot Reboot IP phone some setting needs to reboot to make it works Please always save config before reboot otherwise the setting will return to previous setting www stephen tele com 3 Use keypad configure SVP305 IP phone 3 1 Keypad function User can configure SVP305 through its keypad List below is the keypad function Keypad Mode Function Display Idle mode Show current time Sysinfo Idle mode circularly show phone number wan ip gateway info Menu OK Idle mode enter config mode default password 123
17. e ftp user abc password 123 ip 202 112 20 15 file SVG200SP dlf 5 1 12 upload configure file usage upload ftp user xxx password xxx ip x x x x file xxx upload tftp ip x x x x file xxx www stephen tele com 6 Network Diagnosis There are some telnet commands for checking your network Now Listing below for your information www google com show basic 7 Restore to factory default setdefault clear IP phone settings expect network part setdefault all clear all settings www stephen tele com 8 POST Mode safe mode ch Telnet 192 168 10 1 Voip Fhone System Post lersion 2 8 Date Mar 6 2686 16 49 37 Show Mac Address FIP Update Image Clear Configuration Exit and Reboot SVP305 provide safe mode When there is booting problem because of setting problem or firmware problem User can restore the factory setting or upgrade to a new firmware to solve this problem How to enter safe mode There will be a schedule bar in the SVP305 booting procedure press key within the first 5 seconds then the phone will go to POST mode It has a default ip 192 168 10 1 in POST mode User may change the PC s IP address to 192 168 10 xx and telnet to 192 168 10 1 to access the IP phone in POST mode User can accord the guide in post mode to clear the settings or upgrade the firmware www stephen tele com 9 FAQ 9 1 How many servers may SVP305 register simultaneously SVP305 is able to register two SIP servers
18. ed transfer If A is the SVP305 user and B calls and talking with A through VoIP A can press FWD button to hold the call with B and then enter C s number B will be transferred to C and can talk with C Attended transfer If Ais the SVP305 user and B calls and talking with A through VoIP A can press Hold button to hold the call with B and then enter C s number to talk will C and press Hold to switch back to A and then press FWD key B will be transferred to C and can talk with C gt 3 Way Conference Calls Check Enable Three Way Call Assume A is the SVP305 user and B calls and talking with A through VoIP A can press FWD button to hold the call with B then enter and then enter C s number to talk with C and then press button again to make 3 way conference calls www stephen tele com 9 7 How to use the record function Call Service Call Forward off Busy No Answer Always Phone Number Addr Port S060 C Mo Disturb C Ban Outgoing SVP305 provides record function With this function user may record three VoIP message and one local message Active answering machine Select Enable Voice Record to active answering machine and config No Answer Time If there is an incoming call and no one answer the call After timeout SVP305 will auto answer this call and ask the caller to leave message Incoming Record Playing play the message when recording User Defined Voice Use
19. ephen tele com 2 3 Network 2 3 1 Wan Config IP Phone WAN Configuration Active IP Current Hetmask MAC Address Current Gateway 132 165 0 137 255 255 255 0 00 09 45 52 9e 60 132 165 0 1 static DCH PPPOE WAN port network setting page Support static IP dynamic obtain IP and PPPoE gt Configure Static IP Enable Static Set SVP305 s IP address in the P Address Set netmask in the Netmask field Set router IP address in the Gateway DNS Domain Set local DNS server in the Preferred DNS and the Alternate DNS Configure to dynamic obtain IP Enable DHCP lf there is DHCP server in your local network SVP305 will automatically obtain WAN port network information from your DHCP server Configure PPPoE Enable PPPoE www stephen tele com D PPPoE server Enter ANY if no specified from your ITSP Enter PPPoE username and pin in the username and password SVP305 will automatically obtain WAN port network information from your ITSP if PPPoE setting and the setup are correct Stephen Technologies Co Limited Notice If user accesses the IP phone through WAN port He She should use the new IP address to access the IP phone when the WAN port address was changed www stephen tele com 2 3 2 LAN Config IP Phone LAN Configuration p 192 168 101 Netmask 255 255 255 0 DHCP Service NAT H you modify Bridge Mode Ip or Netmask the device wi
20. ephen tele com VAD CNG G 168 compliant 32ms echo cancellation Tone generation and Local DIMF re generation according with ITU T E 164 dial plan and customized dial rules Hotline Speed Dial Call Forward Call Transfer 3 way conference calls Record Caller ID display DND Do Not Disturb Black List Limit List Upgrade firmware through FTP TFTP or HTTP Web management Telnet remote management adjustable user password and super password 1 5 Standard and Protocols IEEE 802 3 802 3 u 10 Base T 100Base TX PPPoE PPP Protocol over Ethernet DHCP Client and Server Dynamic Host Configuration Protocol G 711 u a G729 G7231 5 3 6 3 audio Codec SIP RFC3261 RFC 2543 IAX2 TCP IP Internet transfer and control protocol RTP Real time Transport Protocol RTCP Real time Control Protocol VAD CNG save bandwidth Telnet Internet s remote login protocol DNS Domain Name Server TFTP Trivial File Transfer Protocol HTTP Hyper Text Transfer protocol FTP File Transfer protocol 1 6 Compliant Standard e CE EN55024 EN55022 FCC part15 RoHS 1 7 Operating requirement Operation temperature 0 to 40 C 32 to 104 F Storage temperature 30 to 65 C 22 to 149 F Humidity 10 to 90 no dew 1 8 Package Size 338x220x85mm Packing List v SVP305 IP phone v Power adaptor out put 12v 500mA v Manual CD www stephen tele com onma 1 9 Installation Use ethernet cable to connect SVP305
21. filter no out access gt DHCP path lt config dhcp gt add DHCP rule entry name xxx Startip X x x x endip x x x X netmask x x x x gateway x x x x dnsserver x x x x _time xxx Example lt conftig dhcp gt entry name lan2004 startip 192 168 1 2 endip 192 168 1 254 netmask 255 255 255 0 gateway 192 168 1 1 dnsserver 192 168 10 18 delete DHCP rule no entry name xxx Example lt config dhcp gt no entry name lan2004 Show DHCP settings show disable Jenable DNS relay no dns relay gt dialrule path lt config dialrule gt disable enable End with noJendchar Set end with fix length fixlen xxx Disable end with fix length no fixlen Set timeout to send timeout send xxx Disable timeout to send no timeout send Add digital map entry prefix xxx length xxx Example lt config dialrule gt entry prefix 010 length 11 Delete digital map rule no entry prefix xxx Example lt config dialrule gt no entry prefix 010 Show current digital map show gt LAN interface settings path lt config interface fastethernet lan gt disable Jenable bridge mode no bridgemode disable enable DHCP service no dhcp server disable Jenable NAT no nat www stephen tele com Show current DHCP rules dhcpshow Show LAN port IP address jpshow Show NAT info natshow Change LAN port IP address p addr x x x x mask X x X X Example lt config in
22. ip info Show www stephen tele com D 5 1 3 Debug Level 0 7 path lt debug gt show debug setting disable enable debug all modules disable enable debug app module disable enable debug cdr module disable enable debug sip module disable enable debug tel module disable enable debug dsp module 5 1 4 download configure to flash usage download tftp ip x x x x file xxx Stephen Technologies Co Limited Show NO all xxx NO app xxx NO Cdr xxx NO sip xxx no tel xxx NO dsp xxx download ftp user xxx password xxx ip X x x x file xxx Example download ftp user abc password 123 ip 202 112 20 15 file SVG200SP cfg 5 1 5 password usage password Enter new password xxx Confirm new password xxx 5 1 6 reload usage reload Reboot system 5 1 7 show system running info gt accesslist path lt show gt show accesslist firewall settings Example lt show gt accesslist gt basic path lt show gt show network status Example lt show gt basic gt call path lt show gt show current call info Example lt show gt call active gt capability path lt show gt show CODEC capability Example lt show gt capability gt debugging path lt show gt show debug info Example lt show gt debugging gt dhcp server www stephen tele com tr S path lt show gt show LAN status and DHCP server info Example lt show
23. limit to SVP305 IP phone When MMI filter is enable Only IP address within the start IP and end IP can access SVP305 IP phone www stephen tele com a Stephen Technologies Co Limited 2 5 9 Audio Settings IP Phone DSP Configuration Coding Rule 4729 G729 Payload Length Signal Standard Handdown Time mz Input Volume 1 91 Output Volume 1 9 Handfree Volume 4 Je 9 d YAD CODEC select the prefer CODEC support ulaw alaw G729 and G7231 5 3 6 3 Signal Standard Signal standard for different area Input Volume Handset in volume Output Volume Handset out volume Handfree Volume Hand free volume Handdown Time hand down detect time G729 Payload Length G729 payload length VAD Enable disable Voice Activity Detection www stephen tele com 2 6 Dial Peer Settings Dial Peer Call Mode Destination Del length por Jais s az al OOOO oaie l se a set Dm ze emm mm ons mem w OOOO Please refer to How to use dial rule for detail www stephen tele com 2 7 Config Manage Save Config save current settings Clear Config restore to default settings Backup Config Backup the config file via point the right key of mouse gt save target as gt will pop a save window then type the config file name in the File name the file type is text file Notice clear config in admin mode all settings restores to factory default clear config in guest modem all settings except sip advance sip restore to fact
24. ll auto save and reboot Bridge Mode Enable this option to switch to bridge mode IP phone won t assign IP for its LAN port in bridge mode and its LAN and WAN port will be in the same network This setting wont take effect unless you save the config and reboot the device IP Netmask Set the IP and Netmask for the LAN DHCP Server Enable DHCP service in LAN port NAT Enable NAT Highest Priority of Voice Quality Enable this option to guarantee voice quality If there is high flux in the LAN port SVP305 will limit the stream rate www stephen tele com 2 4 VoIP 2 4 1 SIP Config IP Phone SIP Registered Configuration Register Server Acdldr Proxy Server Addr Register Server Port Proxy Server Port Register Phone Hu 9552532 Register Expire Time seconds Detect Int Phone umber RFC Protocol Edition RFCSZE1 me sername mber erval Time Setting page of public SIP server Register Server Addr Register address of public SIP server Register Server Port Register port of public SIP server default port is 5060 Register Username Username of your SIP account Always the same as the phone number Register Password Password of your SIP account Proxy Server Addr IP address of proxy SIP server SIP provider always use the same IP for register server and proxy server in this case you don t need to configure the proxy server information Proxy Server Port Signal port of SIP proxy Proxy Username prox
25. n Technologies Co LTD Stephen Technologies Co LTD makes no warranties implied or otherwise in regard to this document and to the products described in this document The information provided by this document is believed to be accurate and reliable to the publication date of this document However Stephen Technologies Co LTD assumes no responsibility for any errors in this document Furthermore Stephen Technologies Co LTD assumes no responsibility for the use or misuse of the information in this document and for any patent infringements that may arise from the use of this document The information and product specifications within this document are subject to change at any time without notice and without obligation to notify any person of such change STEPHEN TECHNOLOGIES CO LIMITED Building NO 5 YinHu Industry Area JinHu Road NO 38 LuoHu District Shenzhen China 518029 Tel 86 755 83016956 Fax 86 755 83016321 Website www stephen tele com Email support stephen tele com www stephen tele com
26. nal Configure the port of the destination default is 5060 in SIP Alias optional Set up the Alias We support four Alias as below Alias need to co work with the Del Length gt add xxx add prefix to the phone number can set to reduce the dial length gt all xxx replace the phone number with the xxx can use as speed dial function gt del delete the first N numbers N is set in the Del Length gt rep xxx replace the first N numbers N is set in the Del Length For Example Use wants to place a call 8610 62281493 then you can set the phone number in the dial rule as O10T and set the Alias as rep 8610 and set the Del Length to 3 Then all calls begin with 010 will be changed to 8610 XXXXXXXX Suffix optional Configure suffix show no suffix if not set Instance www stephen tele com Dial Peer Munde en n oe e remm om en eem no 2T rule If the call starts with 2 the first 2 will be deleted and the rest number will be sent to private SIP server 3T rule If the call starts with 3 the first 3 will be deleted and the rest number with be sent to public SIP server 123 rule Dial 123 and will send 8675583018049 to your server Used as speed dial function OT rule If the calls is begin with 0 the first O will be replace by 86 Means that if you dial 075583018049 and SVG200SP will send 8675583018049 to your server 179 rule when you dial 179 the call with send to 192 168 1 179 suit for LAN application without set
27. number 100 ip 202 112 10 100 port 5060 protocol sip www stephen tele com D Disable call forward disable enable call transfer disable enable call waiting Set prefer codec Set DTMF gain Set black list Show black list Set input volume Set outgoing limit list Show outgoing limit list Set output volume disable enable outgoing limit disable enable black list disable enable outgoing limit and black disable enable 3 way conference Show port settings gt PPPoE settings path lt config pppoe gt PPPoE account settings Stephen Technologies Co Limited no callforward no calltransfer no callwaiting COd C XXX dtmfvolume xxx in limit xxx in limit input Xxx Out limit xxx Out limit OUtput Xxx no shutdown out no shutdown in ist no shutdown no threetalk Show auth user xxx password xxx Example lt config pppoe gt auth user aaa password 123456 disable enable service settings Show pppoe settings gt QOS settings path lt config qos gt delete jadd QoS table entry Example lt contig qos gt entry addr 202 disable Jenable include QOS table Show QoS settings SNOW gt SIP settings path lt config sip gt disable enable registration disable enable auto detect server Set sip domain Set DTMF mode Set auto detect interval time Set RFC edition disable Jenable auto swap server Set sip account Set local SIP
28. ory default www stephen tele com 2 8 Update Web Update Update IP phone s settings or firmware Firmware file is z extension when configure file is cfg extension SVP305 will auto select configure update or firmware update according the extension TFTP FTP Update upload download the configure file with FTP or TFTP server or download firmware from FTP or TFTP server Back up configure file to your FTIP TFTP server FTP TFTP Download configure use cfg extension The Type includes two parts of config file export and config file import Config file export export the config file Config file import import the config file Auto update SVP305 IP phone support FTP and TFTP auto update The gateway will auto obtain the configure file from your update server if configured To obtain the original configure file you can use the FTP TFTP back up as describe above Configure file using module structure user may remain the concerned modules and remove other modules Put the configure file in the root directory of update serve when finish editing Auto Update Server Configuration 192 165 1 53 ATAcontigure ctg digitalrmap FTF e Configure file version was in the lt lt VOIP CONFIG FILE gt gt and lt GLOBLE CONFIG MODULE gt ConfFile Version www stephen tele com For instance Gateway original version is lt lt VOIP CONFIG FILE gt gt Version 1 0000 lt GLOBLE CONFIG MODULE gt ConfFile Version 6 User may e
29. phen tele com Digital Map Digital Map Configuration End with 2 O Fixed Length Time out Digital Map Table Rules 3 3 5 x2xxx 5 3 7 gjss Digit map is a set of rules to determine when the user has finished dialing SVG200SP support below digital map Digital Map is based on some rules to judge when user end their dialing and send the number to the server SVG200SP support following digital map End With Use as the end of dialing Fixed Length When the length of the dialing match the call will be sent Timeout Specify the timeout of the last dial digit The call will be sent after timeout Prefix User define digital map represents the range of digit can be a range such as 1 4 or use comma such as 1 3 5 or use a list such as 234 X represents any one digit between 0 9 Tn represents the last digit timeout n represents the time from 0 9 second it is necessary Tn must be the last two digit in the entry If Tn is not included in the entry we use TO as default it means system will sent the number immediately if the number matches the entry Example 1 8 xxx All number from 1000 to 89999 will be sent immediately OXXXXXXX 8 digits numbers begin with 9 will be sent immediately 911 Number 911 will be sent will be immediately 99xT4 3 digits numbers begin with 99 with be sent after four seconds www stephen tele com 2 5 7 Call Service Settings Call Service
30. s LAN port and your computer Set your computer s ip to the network 192 168 10 x or using dynamic obtain IP Open your web browser and key in 192 168 10 1 Then you will see the logon page of SVP305 the default username and password is admin admin for administrator and guest guest for guest Set up page for VoIP use only www stephen tele com 2 Web Configuration 2 1 Access Web setting page Enter SVP305 IP address in the web browser and press ENTER to go to the log on page and key in the username and password to access SVP305 setting page Default username and password is Administrator Username admin password admin User Username guest Username guest Current State Username admin Network Password DEER VoIP Advance Dial peer Config Manage Update System Manage www stephen tele com D 2 2 Current state Stephen Technologies Co Limited IP Phone Running Status Hetwork Connect Mode MAC Address 00 09 45 52 a1 c8 IP Address 1921681 32 192 1684 254 IP Address 19216810 DHCP Server Volt Default Protocol SIF unedited En Version VOIP PHONE v1 0 Moy 16 2006 17 26 52 This page shows SVP305 s running state Network shows the WAN and LAN port connecting state and current settings VoIP part show the working state of VoIP you can see whether SVP305 has registered the public sip server Phone Number public sip and private sip phone numbers www st
31. simultaneously and redundancy servers User can configure the dial peer to route calls between these servers Please refer How to use the dial rule for detail 9 2 Why the settings vanish after reboot Please go to Config Manage Save Config to save your setting always 9 3 How to use the dial rule SVP305 provide flexibledial rule with different dial rule configure user can easily implement the following function Replace delete or add prefix of the dial number Make direct IP to IP call Place the call to different servers according the prefix You can click Add to add a new dial rule Below is the detail setting of the dial rule Phone Number The Number suit for this dial rule can be set as full match or prefix match Full match means that if the number user dialed is completely the same as this number the call will use this dial rule Prefix match means that if prefix of the number that the user dials is the same as the prefix the call will use this dial rule to distinguish from the full match case you need to add T after the prefix number in the phone number setting Call Mode support SIP Destination optional call destination can be IP or domain Default is 0 0 0 0 in this case the call will be routed to the Public SIP server If you set the destination to 255 255 255 255 then the call will be routed to the private SIP server Also you can key other address here to make direct IP calls Port optio
32. terface fastethernet lan gt ip addr 192 168 1 10 mask 255 255 255 0 gt WAN interface settings path lt config interface fastethernet wan gt disable enable dhcp client no dhcp disable Jenable pppoe no pppoe disable Jenable QOS no gos Set default gateway IP gateway X X X X Clear default gateway IP no gateway Set WAN port IP address Ip address x x x x mask x x X X Example lt config interface fastethernet wan gt ip addr 202 112 241 100 mask 255 255 255 0 You need to reconnect if the WAN port has been changed Show WAN port settings show gt MMI Filter path lt config mmifilter gt add filter rule entry Start x x x x end x X X X Example lt config mmifilter gt entry start 202 112 20 1 end 202 112 20 255 Delete filter rule no entry start x x x x Example lt config mmifilter gt no entry start 202 112 20 1 Show filter rule SNOW disableJenable MMI filter no start filter gt NAT settings path lt config nat gt disable enable ftp alg no ftpalg disable enable ipsec alg no ipsecalg disable enable pptp alg no pptpalg Add TCP mapping rule tcp entry ip x x x x lanport xxx wanport xxx Example lt config nat gt tcp entry ip 192 168 1 5 lanport 1720 wanport 1000 Delete TCP mapping rule no entry ip x x x x lanport xxx wanport xxx Example lt config nat gt no tcp entry ip 192 168 1 5 lanport 5060 wanport 1000
33. unction The realized voice packets transfer at the same VLAN The prerequisite is it must the same as VLAN of upper switch The value range are 1 4094 DiffServ Enable If enable the VLAN service it indicates use DSCP mode to realize three layers QoS This moment the DSCP of SIP signals which between IP Phone and MGC It will use Class Selector 5 The value is OxAO And the DSCP of mediums information In RTP packets would be used the values of DiffServ Value field DiffServ Value The value range 0x28 0x30 0x38 0x48 0x50 0x58 0x68 0x70 0x78 0x88 0x90 0x98 0xb8 default is Oxb8 oxb8 stands for best fast transmission 28 30 is guarantee for the transmission priority for the 1st rank 48 58 is guarantee for the transmission priority for the 2nd rank 68 78 is guarantee for the transmission priority for the 3rd rank 88 98 is guarantee for the transmission priority for the 4th rank www stephen tele com 2 5 6 Advance SIP settings IP Phone Advance SIP Configuration Public Registered Private Unregistered STUN NAT Transverse FALSE mort Private Domain seconds Private Humber STUN Effect Time seconds Private User Agent Voip Phone 1 0 Private Server Type Enable PRACK Enable Keep Authentication A Auto Detect Server d Enable Session Timer d Signal Encode d Rte Encode C Enable Private Register _ Enable SIP Stun This page is used to set the private sip server stun server and back up sip server information STUN Ser
34. up a Sip server 9 4 How to use speed dial function There are 9 speed dial keys in the SVP305 panel Usage Set speed dial number press the speed key and enter the speed dial number and then press Menu OK key to save the setting Pick up the handset and press the speed dial key to dial the pre define number 9 5 How to configure digital map Please refer the digit_map 9 6 How to use Call Forward Call Transfer and 3 way Conference calls User may set up the configuration in the Call Service page to use these value add service www stephen tele com Call Service at O Busy No Answer Always Mo Disturb Ban Outgoing Tr gt Call Forward Forward when busy select Busy m the Call Forward Field and Key in the destination phone number in the Forward Number If some one calls you when you having a call the caller will be forwarded to the destination number Forward no answer Select No Answer in the Call Forward Field and Key in the destination phone number in the Forward Number fill the time in the No Answer Time If some one calls you and no one answer the caller during the No Answer Time the call will be forward to the destination number Forward Always Select Always in the Call Forward Field and Key in the destination phone number in the Forward Number then any one call this gateway will be forward to the destination number gt Call Transfer Check the Enable Call Transfer Unattend
35. ver IAX Server Addr Register address of public IAX server IAX Server Port Register port of public IAX server default port is 4569 Account Name Username of your SIP account Always the same as the phone number Account Password Password of your IAX account Local port Signal port of local default port is 4569 Phone Number Phone number of your IAX account Voice mail number If the IAX support voice mail but your username of the voice mail is letters which you can not input with the ATA then you use the number to stand for your username Voice mail text if IAX support voice mail config the domain name of your mail box here Echo test number If the platform support echo test and the number is test form the config the test number to replace the text format The echo test is to test the woring status of www stephen tele com terminals and platform Echo test text echo test number in text format Refresh time IAX refresh time Enable Register enable or disable register IAX Default Protocol Set IAX 2 as the default protocol if not the system will choose SIP as default Enable G 729 Using G 729 speech coding mandatory consultations 2 5 Advance 2 5 1 DHCP Server DHCP Service DNS Relay lanz005 192 168 10 2 192 165 10 50 1440 205 255 255 0 192 165 10 1 192 165 10 1 Lease Table Name lanZ005 3 DHCP server manage page User may trace and modify DHCP server information in this page DNS Relay enable DNS rel
36. ver setting STUN Server Addr configure stun server address STUN Server Port configure stun server port default 3478 STUN Effect Time stun detect NAT type circle unit minute Enable SIP STUN enable disable stun Enable PRACK Whether to make gateway or IP phone support Prack function in SIP we suggest you keeping default setting Enable Keep Authentication registering signal together with the authentication information If enable it the server will confirm the registering and send back the confirmation massage directly instead of requesting the terminals to send authentication information if needed Auto Detect Server Whether to enable the function of auto detecting the server With this function your ATA and IP phone will send information to auto detect the server at every period of time If find the server is not available it will try to register the server again Enable Session Timer Whether to enable te RFC4028 Signal Encode Wherther to enable the signal encrypt Rtp Encode Whether to enable the voice encrypt Enable Private Register Whether to enable the second SIP Server to register Please refer to SIP_Config for the setting for how to set the public alter server User can register two sip servers public sip server and private sip server these two sip servers are independent from each other and running in the same time www stephen tele com For how to configure private sip server Please refer to SIP_Config www ste
37. y server username Proxy Password proxy server password Domain Realm SIP domain enter the sip domain if any otherwise SVP305 will use the proxy server address as sip domain Local SIP port Local SIP register port default 5060 Phone Number Phone number of your SIP account Register Expire Time register expire time default is 600 seconds SVP305 will auto configure this expire time to the server recommended setting if it is different from the SIP server Detect Interval Time Co work with the Auto Detect Server if Auto Detect Server is enable SVP305 will periodically detect if the SIP server is available according this setting User Agent Encrypt Key The particular service system decrypts of the key matching with the server Type usage the key provide by the particular service system supplier default is empty www stephen tele com Server Type The particular service system supplier carries out the sign and speeches to encrypt default is common DTMF Mode DTMF signal sending mode support RFC2833 DIMF_RELAY inband audio and SIP info RFC Protocol Edition Current SVP305 SIP version Set to RFC 2543 if the gate need to communicate to devices such as CISCO5300 using the SIP 1 0 Default is RFC 3261 Enable Register Enable Disable SIP register SVP305 won t sent register info to SIP server if disable register 2 4 2 lax2 Config IP Phone IAX Registered Configuration GE SE Ce E Setting page of public IAX ser
Download Pdf Manuals
Related Search