Home

Solara 3G/ Spree 3G Wheelchair

1. 49 Replacing Conventional Armrest Pads a a teen tnnt ten tentent teen tentent EE tenete teen ten tentem ten E teen stn teen ttn EDEA 51 Installing Removing ace eet tier e EN e beste tss ve Der n e E us cedet E db 51 Adjusting The T Arms 42153 Adjusting T Arm Sockets rrt d RA HERE ORE EHE AERE AEG LE REA ind ia Sal aaa ean canes aa ates 56 Solara 3G Spree 3G Wheelchair 3 Part No 1154295 CONTENTS Adjusting T Arm Transfer Assists And or Side Guards eese tte tent tet tentenn tentent tente tten teen ten ttn 57 Using Installing Adjusting Locking Cantilever Arms eese sn ttenten testen tentent sette ttenten tenentes 58 Adjusting Locking Cantilever Arm Height ersinnen nnise R AAE a aAA 59 Using Installing Adjusting Non Locking Cantilever Arms 61 Arm Pad Replacement for Cantilever 5 4 4 22 63 5 64 Folding Unfolding the Back Assembly 4 08 4 4 42222222 64 Adjusting the Height of the Adjustable Height Back Canes esee tentenn tentent tentent tenente tenen ten tenente nent 65 A
2. NOTE Rear view of wheelchair and human surrogate secured on test platform and tilted to 45 degrees FIGURE 4 Vehicle Anchored Belts Part No 1154295 115 Solara 3G Spree 3G Wheelchair 18 TRANSPORT READY OPTION Seating System WARNING This wheelchair has been tested for seating in a motor vehicle with the factory installed seating system only When feasible wheelchair occupants should transfer into the vehicle seat and use the OEM Original Equipment Manufacturer vehicle installed restraint system Ensure that the factory installed seating system is secured to the wheelchair frame before operation Refer to the seating system owner s manual Positioning Belts WARNING angle of the pelvic belt should be within the preferred zone of 45 to 75 degrees to the horizontal OR within the optional zone of 30 to 45 degrees to the horizontal Steeper side view pelvic belt angles are especially important if the pelvic belt is intended to be used for postural support in addition to occupant restraint in a frontal crash Steeper angles will reduce the tendency for a vertical gap to develop between the user and the belt due to compliance of seat cushions and belt movement thereby reducing the tendency for the user to slip under the belt and for the belt to ride up on the soft abdomen during normal use Steeper belt angles also reduce the tendency for upper torso belts to pull the pelvic belt onto the abdomen during frontal impa
3. FIGURE 3 Using the Pull to Lock Wheel Locks 89 Solara 3G Spree 3G Wheelchair Part No 1154295 Wheel Locks Anti Tippers heel Lock Handle Wheel Lock Shoe v Handle Unlocked Position Side View Locked Position Side View E 52 Wheel Lock Shoe ur Locked Position Wheel to k darse Unlocked Position Top View Handle Top View Wheel Lock Handle FIGURE 4 Using the Push to Lock Wheel Locks Solara 3G Spree 3G Wheelchair 90 Part No 1154295 Wheel Locks Anti Tippers Footlock Push down on the footlock lever to engage the footlock 2 Lift up on footlock lever to disengage the footlock Push Down to Locked Unlocked Engage Py Footlock Lever eet Lift Up to Disengage Rear Wheel 548 Rear Wheel FIGURE 5 Using the Push to Lock Wheel Locks Footlock Part No 1154295 91 Solara 3G Spree 3G Wheelchair Wheel Locks Anti Tippers A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur ALWAYS engage both hublocks and reduce the gap distance before transferring to and from the wheelchair Turn all casters parallel to the object you are transferring onto Hublocks are not brakes DO NOT attempt to stop a moving wheelchair with the hublocks Users should be evaluated by a care provider to determine the suitability of the hub lock option Repetitive uncont
4. Keep detent balls clean Wheelchairs with TRRO or TRBKTS Only Only use the transport brackets included with TRRO and TRBKTS for the purposes described in this manual Tire Pressure DO NOT use your wheelchair unless it has the proper tire pressure 5 DO NOT overinflate the tires Failure to follow these recommendations may cause the tire to explode and cause bodily harm The recommended tire pressure is listed on the side wall of the tire Part No 1154295 15 Solara 3G Spree 3G Wheelchair 2 SAFETY WARNING Weight Training Invacare DOES NOT recommend the use of its wheelchairs as a weight training apparatus Invacare wheelchairs have NOT been designed or tested as a seat for any kind of weight training If occupant uses said wheelchair as a weight training apparatus INVACARE SHALL NOT BE LIABLE FOR BODILY INJURY AND THE WARRANTY IS VOID Weight Limitation Invacare Solara 3G wheelchair has a weight limitation of 300 Ibs 136 kgs Invacare Solara 3G wheelchair with the Heavy Duty package has a weight limitation of 400 Ibs 181 kgs Invacare Spree 3G wheelchair has a weight limitation of 200 Ibs 9 kgs Solara 3G Spree 3G Wheelchair 16 Part No 1154295 3 PRODUCT LABELING 3 Product Labeling 31 Wheelchairs without Transport Ready Option NO WHEELCHAIR HAS BEEN APPROVED FOR USE AS A SEATING SURFACE WITHIN A MOTOR VEHICLE THIS LABEL IS FOR S INFORMATIONAL PURPOSES ONLY LIABILITY ISSUES WERE NOT CONSIDER
5. 10 6 Adjusting The T Arms Adjusting T Arm Height 4 Unlock the T Arm by flipping the T Arm release lever towards the inside of the wheelchair If necessary pull the T Arm release lever out and rotate 180 so it can be flipped towards the outside of the wheelchair Slide the T Arm to one of Low Height T Arms Nine positions High Height T Arms Seven positions If the inside T Arm post does not slide up and down in the outside T Arm post as desired perform one of the following Tighten Tightening the set screws on the outside T Arm post will make it more difficult to move the inside T Arm post up and down Loosen Loosening the set screws on the outside T Arm post will make it easier to move the inside T Arm post up and down Lock the T Arm by flipping the T Arm release lever towards the front of the wheelchair Adjusting T Arm Width Bes Oo Remove the two mounting screws that secure the arm pad to the arm tube Turn the arm pad around and reposition the arm pad on the arm tube Re secure the arm pad to the arm tube with the two mounting screws Tighten securely Repeat for the opposite side if necessary Part No 1154295 53 Solara 3G Spree 3G Wheelchair 10 ARMS T Arm T Arm Release Lever UNLOCKED Position T Arm Release Lever LOCKED Position Set Screws Adjusting T Arm Width Arm Tube Arm Pad Mounting Mounting Screw 8 Screw FIGURE 7 Adjusting T Arm H
6. Moving the rear wheel axle mounting brackets to any of the forward positions will change the center of gravity of the wheelchair making the wheelchair less stable ALWAYS make sure that the wheelchair is stable both in the full reclined back at 180 position and the full upright back at 90 position before using the recliner option Before using the recliner option make sure the anti tipper wheel assemblies are in the lowest adjustment hole adjustment hole closest to the ground floor ALWAYS engage both wheel locks while reclining or inclining sitting up the wheelchair Both gas cylinders MUST be operational and adjusted properly before using the recliner DO NOT operate the recliner option if only one of the gas cylinders is operational or adjusted properly Make sure the patient is properly positioned in the wheelchair before reclining or inclining sitting up to maintain maximum stability and safety Solara 3G Spree 3G Wheelchair 12 Part No 1154295 2 SAFETY A WARNING When returning the occupant of the wheelchair to the full upright position more body strength will be required for approximately the last twenty degrees of incline sitting up Make sure to use proper body mechanics use your legs or seek assistance to avoid injury ALWAYS return the back to the upright position before lifting the wheelchair Operation Information Unless otherwise noted all service and adjustments should be performed while the wheelchair
7. Yes you can Solara 3G Spree 3G Wheelchair User Man ual DEALER This manual MUST be given to the user of the product USER BEFORE using this product read this manual and save for future reference CONTENTS 8 E 6 idle 6 Limited Warranty sesira eR RR Rn Rae EA AOT ipe HE ENERO d bf e dtt ERR ded 7 PACCO de 8 General GUI pp c E EEEE A 8 3 PRODUCT LABELING 4 89 17 Wheelchairs without Transport Ready Option 407 Wheelchairs with Transport Ready 2 18 4 TECHNICAL DATA 19 Typical Product re ate iet ipsi eei e DA A obo pee e a a cage eec ote Lo Eee eee 19 5 SAFETY HANDLING OF WHEELCHAIRS scccssssssssssssesssssecsssssessseeesssesesssnsesecsescesssescseescsesessasessseseessessesssessecsessesssesseeasees 22 ichs Ascot 22 Coping With Everyday iR CUR Eee eee e Re e ede 24 A Note to Wheelchair Assistants orem eia eie tre ee iue eer MESH sbervornaactaneonaabesdeenssavessvestaaeeasteansaneasthoossiveodnssadapeaitaebioausdsdecsbee snnte 24 Reaching Eeaning and Bendirig Forward tec et e
8. co 24 Reaching 25 AUP PUA e p S Nat RA et b NR E deat e 25 Stai Way pono 27 Transferring To xand From Other Seats op electi p be RE ce Rate lita aea iie 28 6 SAFETY 5 29 Safety Inspection Checklists rote RO p e RD dbi n Ie E red E 29 Troubleshooting Mechanical t dene a P ERU eee UR a Ee EEr ee loc MES 3l Part No 1154295 2 Solara 3G Spree 3G Wheelchair CONTENTS UEBUnnn 32 enr E 8 MAINTENANCE Mainten rice Safety Preca utions ER DA eter I Rees ue RV s a a M AERA Hee Le AE dU RM eae E A tied dee e ends 33 Suggested Maintenance Proced res eee c at LR M RU b debe tM ee tb cote 33 9 FRONT RIGGINGS 8 35 Installing Removing Footrests 4035 Adjusting Footrest eC e Ee ER OUR CA ER REA RIO RUE ARE ERRARE t AIR eas 36 Installing Adjustable Angle Flip Up Footplate Hinge eene entente tentent tente
9. C Secure the foot lock lever to the connecting wheel lock link in the corresponding adjustment hole D Repeat STEPS 3 for remaining wheel lock bracket 4 Tighten the four mounting screws to 50 inch pounds Engage the footlock and push against the wheelchair to determine if the footlock engages the rear wheels enough to hold the wheelchair Repeat STEPS 1 7 until the footlock engages the rear wheels enough to hold the wheelchair DETAIL A DETAIL B Foot Lock Lever Washers Mounting Wheel Lock Mounting Wheelchair 255 zc m e OX Frame Rear Wheel Adjustment Connecting Wheel Wheel Lock Bracket Holes Lock Link FIGURE 2 Wheel Lock Adjustment Footlock Part No 1154295 87 Solara 3G Spree 3G Wheelchair Wheel Locks Anti Tippers 15 2 Using the Wheel Locks Pull to Lock Wheel locks 1 Pull the wheel lock handle forward to engage the wheel locks 2 Reverse STEP to disengage the wheel locks Push to Lock Wheel locks Push the wheel lock handle forward to engage the wheel locks 2 Reverse STEP to disengage the wheel locks Solara 3G Spree 3G Wheelchair 88 Part No 1154295 Wheel Locks Anti Tippers 1 Wheel Lock Handle te Wheel Shoe Wheel Lock Handle Wheel Lock Shoe Unlocked Position Side View Locked Position Side View Wheel Lock Handle Unlocked a X x Locked Position Position Wheel Lock SM 3 Top View Ed Top View Handle
10. DO NOT operate the wheelchair when the seat frame is in the anterior forward tilt position frame stops in the lower position and approximately 5 forward tilt Serious bodily injury may occur to the patient and or the assistant s Anterior forward tilt is a feature of this wheelchair designed for the use of a healthcare professional or assistant only Engagement of the anterior forward tilt MUST NEVER be performed by the wheelchair user When anterior forward tilt is needed it MUST AL WAYS be engaged by a healthcare professional or assistant Make sure the occupant of the wheelchair is properly positioned and ALWAYS engage both wheel locks Stability All Models The back height seat depth back angle seating system tilt angle seat height size position of the rear wheels size position of the front casters as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the eleven may cause the wheelchair to decrease in stability These adjustments must be performed by a qualified technician ALWAYS make sure that the wheelchair is stable before using the tilt in space Solara 3G Spree 3G Wheelchair 10 Part No 1154295 NOTE When changes to the left hand column occur follow across the chart and refer to the X procedure to maintain the proper stability safety and handling of the wheelchair BACK HEIGHT BACK HEIGHT SEAT DEPTH BACK ANGLE TILT ANGLE CASTER
11. LLI gt 2 Zr 5 FO LEFT RIGHT CASTERS FLUTTER SQUEAKS LOOSENESS IN CHAIR I 172 o o 2 z o CHAIR VEERS If pneumatic tires check for correct and equal pressure Check for loose stem nuts bolts Check that casters contact ground at the same time Part No 1154295 3l Solara 3G Spree 3G Wheelchair 7 TRANSPORTING 7 Transporting 7 Transporting Remove the seating system Refer to the seating system Owner s Manual for installation and removal of the seating system l 2 Remove the footrests Refer to Installing Removing Footrests on page 35 or Adjusting Footplate Height and Calfpad Height Depth on page 42 3 Remove the rear wheels Refer to Installing Removing Rear Wheels on page 81 4 Remove the armrests Refer to Installing Removing Dual Point Armrests Fixed And Adjustable Height on page 46 or Installing Removing T Arms on page 51 5 Remove the stroller handle if applicable Refer to Installing Removing Non Adjustable Stroller Handles on page 68 6 Pick up on the back release levers and push the back towards the front of the wheelchair Refer to Folding Unfolding the Back Assembly on page 64 Solara 3G Spree 3G Wheelchair 32 Part No 1154295 8 MAINTENANCE 8 Maintenance 8 1 Maintenance Safety Precautions A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise
12. Place foot on the step tube and begin to tilt the wheelchair toward you Apply a continuous downward motion until the balance point is achieved and the front casters clear the curb At this point the assistant will feel a difference in the weight distribution Part No 1154295 25 Solara 3G Spree 3G Wheelchair 5 SAFETY HANDLING OF WHEELCHAIRS WARNING When lowering the front casters of the wheelchair DO NOT let the wheelchair drop the last few inches to the ground This could result in injury to the occupant and or damage to the wheelchair Step Tube Roll the wheelchair forward and slowly lower the front of the wheelchair Ec in one continuous movement onto the sidewalk DO NOT let the wheelchair drop the last few inches to the ground This could result in uu injury the occupant Push the wheelchair forward until the rear FIGURE 5 4 Tipping Curbs Method Wheelchair with wheels roll up and over the curb Step Tubes Tipping Curbs Method 2 Wheelchair without Step Tube This method requires two assistants The second assistant should be positioned at the front of the wheelchair lifting upward on a non removable non detachable part of the wheelchair frame when lifting the wheelchair and stabilizing the wheelchair when the wheelchair is being lowered to the ground Rotate the anti tippers so the anti tip wheels are pointing up The first assistant should stand on the sidewalk and turn the wheelchair so that the rear
13. injury or damage may result CAUTION DO NOT overtighten hardware attaching to the frame This could cause damage to the frame tubing 8 2 Suggested Maintenance Procedures l Keep quick release axles free of dirt and lint to ensure positive locking and proper operation Refer to Adjusting The Quick Release Axle on page 83 A WARNING DO NOT use WD 40 3 in 1 or other penetrating lubricants on quick release axles Otherwise binding and or damage to the wheelchair may occur e 2 Clean quick release axles once a week with a Teflon lubricant A WARNING DO NOT use your wheelchair unless it has the proper tire pressure p s i DO NOT overinflate the tires Failure to follow these suggestions may cause the tire to explode and cause bodily harm The recommended tire pressure is listed on the side wall of the tire Replacement of a pneumatic tire or tube MUST be performed by a qualified technician Part No 1154295 33 Solara 3G Spree 3G Wheelchair 8 MAINTENANCE CAUTION As with any vehicle the wheels casters and tires should be checked periodically for cracks and wear and should be replaced If tires are pneumatic recommended tire pressures will be listed on the side wall of the tires The wheels and tires should be checked periodically for cracks and wear and should be replaced Periodically check handrims to ensure they are secured to the rear wheels Periodically adjust wheel locks as tires wear Refer
14. 12 INCH WHEEL Seat Width 8 1 4 inches 16 24 INCH WHEELS Seat Width 9 1 4 inches Example 16 inch Wide Wheelchair 24114 inches Overall Width OVERALL DEPTH Without Front Riggings Without Front Riggings Short Frame 24 3h inches Short Frame 24 inches Medium Frame 27 KS inches Medium Frame 27 inches Long Frame 30 uP inches OVERALL HEIGHT ADJUSTABLE HEIGHT CANES 20 INCH BACK CANES Seat to Floor Height 20 24 inches 24 INCH BACK CANES Seat to Floor Height 21 inches Seat to floor Height 25 inches SHIPPING WEIGHT 66 Ibs ANTI TIPPERS Standard FOOTREST Swing Away Footrest Standard Articulating Swing Away Footrest elevating Swingaway Footrests Lift Off Footrests Contracture Footrests Optional Part No 1154295 19 Solara 3G Spree 3G Wheelchair 4 TECHNICAL DATA Dual Point Adjustable Height Dual Point Fixed Height Desk Length Dual Point Fixed Height Full Length Adjustable Height T Arms Dual Point Flip Back Canitlever Arms Desk or Full Non Locking Cantilever arms Dual Point Adjustable Height Dual Point Fixed Height Desk Length Dual Point Fixed Height Full Length Adjustable Height T Arms Dual Point Flip Back Cantilever Arms Desk and Full Non Locking Cantilever Arms SEAT Optional SEAT PAN COLOR Black BACK Optional BACK ANGLE 90 to 120 ADJUSTMENT REAR AXLE Quick Release or Fixed REAR W
15. ARMS 10 Arms A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 10 1 Installing Removing Dual Point Armrests Fixed And Adjustable Height WARNING Make sure the locking mechanism is secured before using wheelchair Installing Armrest l Unlock armrest assembly by flipping the arm assembly release lever located on the side rail to the UP horizontal position Detail Armrest locks MUST be in the unlocked position when placing arm into the arm sockets Install armrest assembly into the arm sockets When installed lock the armrest assembly by pressing the release lever into the down vertical position Detail A Repeat STEPS 1 3 for the opposite side of the wheelchair Uy e o Up For adjustable height dual point armrests adjust the height if necessary Refer to Adjusting the Height of the Adjustable Height Armrests on page 48 Removing Armrest l Unlock armrest assembly by flipping the arm assembly release lever located on the side rail to the up horizontal position Detail A 2 Pull up on the armrest assembly to remove the armrest from the arm socket 3 Repeat STEPS 1 2 for opposite side of wheelchair if necessary Solara 3G Spree 3G Wheelchair 46 Part No 1154295 10 ARMS Armrest Assembly DETAIL A See Locked Down Unlocked Up Vertical H
16. NOT use an escalator to move a wheelchair between floors Serious bodily injury may occur Part No 1154295 27 Solara 3G Spree 3G Wheelchair 5 SAFETY HANDLING OF WHEELCHAIRS 5 8 Transferring To and From Other Seats A WARNING BEFORE attempting to transfer in or out of the wheelchair every precaution should be taken to reduce the gap distance Align both casters parallel with the object you are transferring onto Also be certain the wheel locks are engaged to help prevent the wheels from moving CAUTION When transferring position yourself as far back as possible in the seat This will prevent damaged upholstery and the possibility of the wheelchair tipping forward This activity may be performed independently provided you have adequate mobility and upper body strength Position the wheelchair as close as possible along side the seat to which you are transferring with the front casters parallel to it 2 Engage wheel locks 3 Remove or flip back armrests 4 Shift body weight into seat with transfer During independent transfer little or no seat platform will be beneath you Use a transfer board if at all possible Solara 3G Spree 3G Wheelchair 28 Maximum Gap Distance gt FIGURE 5 6 Transferring To and From Other Seats Part No 1154295 6 SAFETY INSPECTION TROUBLESHOOTING 6 Safety Inspection troubleshooting Every six months take your wheelchair to a qualified technician for a thorough inspection
17. about to be reclined Make sure occupant s hands and body are clear of all pinch points Stand behind the wheelchair and grasp the adjustable angle stroller handle firmly Pull up on the trigger release levers to release the gas cylinders Slowly squeeze the trigger release levers and perform one of the following e Reclining Allow the back to recline to the desired angle Returning to upright position Pull up and push the stroller handle towards the front of the wheelchair until the back is in the upright position When the back reaches desired angle slowly release the handles of the recliner cable assemblies Solara 3G Spree 3G Wheelchair 96 Part No 1154295 l6 9 Disengage the wheel locks Trigger Release Lever FIGURE Recliner Operation 16 2 Replacing Back Headrest Upholstery Back Upholstery Remove the twelve mounting screws and washers that secure the back upholstery to the back canes Remove existing back upholstery from back canes Install new back upholstery onto the back canes Bow oM Install the twelve mounting screws and washers that secure the back upholstery to the back canes Part No 1154295 97 RECLINER BACK OPTION Solara 3G Spree 3G Wheelchair l6 RECLINER BACK OPTION Headrest Upholstery Remove the six mounting screws and washers that secure the headrest upholstery to the headrest extensions Remove the existing headrest upholstery from the
18. and servicing Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair To operate properly and safely your wheelchair MUST be cared for just like any other vehicle Routine maintenance will extend the life and efficiency of your wheelchair 6 l Safety Inspection Checklists Initial adjustments should be made to suit your personal body structure needs and preference Thereafter follow these maintenance procedures A CAUTION As with any vehicle the wheels and tires should be checked periodically for cracks and wear and should be replaced Inspect Adjust Initially Ensure wheelchair rolls straight no excessive drag or pull to one side Inspect clothing guards for bent or protruding metal Ensure that all fasteners on clothing guards are secure Ensure arms are secure but easy to release and adjustment levers engage properly Ensure adjustable height arms operate and lock securely Ensure armrest upholstery has no rips Ensure armrest pad sits flush against arm tube Ensure hand grips are not loose Ensure seat back and or arm upholstery have no rips Ensure trigger release lever cables and handles return when released Inspect handrims for signs of rough edges or peeling finish Ensure there is no excessive side movement or binding when drive wheels are lifted and spun Ensure sealed bearings and axle nut tension are correct Adjust bearing system if wheel wobbles noticeably or bind
19. four mounting screws eight washers and four locknuts Tighten securely Part No 1154295 79 Solara 3G Spree 3G Wheelchair 13 VENT TRAY Washers Two washers are located between the rear hanger bracket and wheelchair frame Washers Mounting Screws Rear Vent Tray Hanger Bracket Front Cross Tube Mounting Screws Rear Vent Tray Mounting Hanger Bracket Screws Front Vent Tray Hanger Bracket Solara 3G Spree 3G Wheelchair 80 Part No 1154295 I4 WHEELS FORKS 14 Wheels Forks WARNING After any adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 14 1 Installing Removing Rear Wheels 1 Quick Release To remove rear wheels reverse this procedure Push in the detent pin of the quick release axle and insert the quick release axle through the center of the rear wheel 2 Push in the tip of the quick release axle again and insert the axle with wheel into the axle mounting plate on the side of the wheelchair frame until the assembly locks in place A WARNING Make sure detent pin and locking pins of the quick release axles are fully released before operating the wheelchair The locking pins MUST be protruding past the inside of the axle mounting plate for a positive lock Keep locking pins clean 3 Ensure quick release axle locking pins are properly engaged and secure in the axle mounting plate by pulling the
20. headrest extensions Install the new headrest upholstery onto the headrest extensions Da Install the six mounting screws and washers that secure the headrest upholstery to the headrest extensions Back Cane Headrest Extension Headrest Upholstery Mounting Screws and Washers Back Upholstery FIGURE 2 Replacing Back Headrest Upholstery Solara 3G Spree 3G Wheelchair 98 Part No 1154295 17 Contracture Foot assembly 17 1 Adjusting the Angle of the Contracture Assembly Bilateral Contracture Footplate Remove the top mounting bolt and locknut that secures the contracture support tube to the angle adjustment plate 2 Rotate the contracture support tube and align with one of the nine mounting holes in the angle adjustment plate 3 Reinstall the mounting bolt and locknut Securely tighten 4 Perform STEPS 4 for remaining footplate Contracture Platform Remove the top mounting bolt and locknut that secures the contracture support tube to the angle adjustment plate 2 Rotate the contracture support tube and align with one of the nine mounting holes in the angle adjustment plate 3 Reinstall the mounting bolt and locknut Securely tighten Part No 1154295 17 CONTRACTURE FOOT ASSEMBLY Mounting Holes Top Mounting Bolt and Locknut Adjustment Plate Contracture Support Tube Angle Adjustment Plate Top Mounting Bolt and Locknut Contractu
21. means of any removable detachable parts of a wheelchair may result in injury to the user or damage to the wheelchair DO NOT stand on the frame of the wheelchair Anti tippers MUST BE attached at all times Solara 3G Spree 3G Wheelchair 14 Part No 1154295 2 SAFETY A WARNING DO NOT use the footplates as a platform When getting in or out of the wheelchair make sure that the footplates are in the upward position ALWAYS use the handrims for self propulsion Inasmuch as the handrims are an option on this wheelchair you may order with or without the handrims Invacare strongly recommends ordering the handrims as an additional safeguard for the wheelchair user If wheelchair is exposed to extreme temperature above 100 F or below 32 F high humidity and or becomes wet prior to use ensure handgrips DO NOT twist on product name here handle otherwise damage or injury may occur ALWAYS use anti tippers When outdoors on wet soft ground or on gravel surfaces anti tippers may not provide the same level of protection against tip over Extra caution MUST be observed when traversing such surfaces DO NOT use the spreader bar or stroller handles for lifting or transporting the wheelchair DO NOT use the spreader bar as a weight bearing support Make sure detent balls of the quick release pin are fully released before operating the wheelchair The detent balls MUST be protruding past the top of the seat plate assembly for a positive lock
22. on page 70 11 8 Installing and Removing a Seating System A WARNING Transport ready option only This wheelchair has been tested for seating in a motor vehicle with the factory installed seating system only Ensure that the seating system is compatible with this wheelchair 2 Refer to the seating system Owner s Manual for installation and removal Solara 3G Spree 3G Wheelchair 70 Part No 1154295 12 TILT 12 tilt A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 12 1 Engaging Tilt In Space WARNING The Invacare Solara wheelchair MUST be operated by an assistant when in ANY tilted position ALWAYS make sure that the wheelchair is stable before using the tilt in space Rear wheels may have to be repositioned rearward depending on the degree of tilt in space required ALWAYS ensure stability before using maximum amount of tilt in space Test wheelchair before it is occupied by the end user to ensure safety DO NOT self propel wheelchair while in the tilted position Always engage both wheel locks while using the tilt in space To lower the seat parallel with the floor reverse the following procedure Place the wheelchair on a level surface Engage both wheel locks Inform the occupant of the wheelchair that the wheelchair is about to be tilted and remind them to lean back Make sure the occupant s hands a
23. rigging support tube Position the new sector block on the front rigging support tube Make sure the locking pin is facing up Secure the new sector block to the front rigging support tube with the existing mounting screw and washer Replacing Clamp on Sector Block Remove the two mounting screws and washers that secure the support bracket and sector block to the front rigging support tube Position the new sector block on the front rigging support tube Make sure the locking pin is facing up Secure the new sector block to the front rigging support tube with the existing mounting screws and washers Tighten securely 44 Mounting Front Rigging me Screw Support Tube Washer Locking Pin Sector Block FIGURE 9 Replacing Bolt On Sector Block Front Rigging Support Tube Mounting Mounting Screw Screw Washer Locking Pin ES 5o m Block FIGURE 10 Replacing Clamp on Sector Block Part No 1154295 Front Riggings 9 10 Installing Impact Guards Calf Strap H Calf Strap Impact guards are standard equipment on Model ST footrests No assembly is required l Remove impact guard calf strap from packaged container 2 Secure the impact guards to the footrest frame 3 Secure the calf strap around the footrest frame with the impact guards attached Impact Guard A H Calf Strap Calf Strap FIGURE 11 Installing Impact Guards Calf Strap H Calf Strap Part No 1154295 45 Solara 3G Spree 3G Wheelchair 10
24. stability and safety ALWAYS engage both wheel locks while reclining or inclining sitting up the wheelchair Part No 1154295 95 Solara 3G Spree 3G Wheelchair 16 RECLINER BACK OPTION SOD Ul che DDR c A WARNING When returning the occupant of the wheelchair to the full upright position more body strength will be required for approximately the last twenty degrees of incline sitting up Make sure to use proper body mechanics use your legs or seek assistance to avoid injury Before using the recliner option make sure the anti tipper wheel assemblies are in the lowest adjustment hole adjustment hole closest to the ground floor Before using ANY recline position of this wheelchair make sure the rear wheels are in the MOST REARWARD position to maintain the stability of the wheelchair DO NOT change the handling maneuverability of the wheelchair by moving the rear wheels to any of the forward positions Moving the rear wheels to any of the forward positions will change the center of gravity of the wheelchair making the wheelchair less stable ALWAYS return the back to the upright position before lifting the wheelchair Make sure occupant s hands and body are clear of all pinch points before reclining back Pinch points exist between spreader bar and gas cylinders Use caution otherwise injury may occur Make sure the wheelchair is on a level surface Engage the wheel locks Inform the occupant of the wheelchair that the wheelchair is
25. to Wheel Lock Adjustment on page 85 Make sure that ALL bolts are tight before operating wheelchair Keep tilt slides and roller bearings free of dirt and lint to ensure proper operation of the tilt mechanism Periodically check the back fold down mechanisms to ensure that they lock the back securely in place Periodically check front caster wheel bearings to make sure they are clean and free from moisture Use a Teflon lubricant if necessary 505500 Tbv U VES ES o Check upholstery for sagging rips or tears 12 Recliners Only Periodically check gas cylinders for oil leaks If oil leak is detected contact Invacare Solara 3G Spree 3G Wheelchair 34 Part No 1154295 Front Riggings 9 Front Riggings A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 91 Installing Removing Footrests This procedure applies to the lift off footrest assembly and elevating legrest Installing Turn footrest to the side open footplate is perpendicular to the wheelchair 2 Insert the footrest assembly mounting pin into the mounting tube of the wheelchair frame 3 Rotate the footrest towards the inside of the wheelchair until it locks into place 4 footplate will be on the inside of the wheelchair when locked in place 5 Repeat STEPS 1 3 for the other footrest assembly 6 f necessary adjust the fo
26. to engage Up the hublocks Disengaging the Hublocks Push hublock pedal up to disengage the hublocks Locked Hublock Lever Down FIGURE 7 Attendant Operated Hublock Foot Operated Hublock Part No 1154295 93 Solara 3G Spree 3G Wheelchair Wheel Locks Anti Tippers 15 4 Installing Adjusting Anti Tippers Al to 2 n inch clearance between the bottom of the anti tipper wheels and the floor MUST be maintained at all times Installing the Anti Tippers I Remove the anti tippers from the accessory carton N WARNING Anti tippers MUST be fully engaged and spring buttons fully protruding out of adjustment holes 2 Press the release buttons in and install the anti tippers with the wheels facing down until the locking buttons lock in place FIGURE 8 3 Adjust the anti tippers Refer to Adjusting the Anti Tippers on page 94 Adjusting the Anti Tippers Depress the release button on the wheeled portion of the anti tipper and slide it up down to achieve b to2 I inch clearance Release Button A WARNING Anti tippers MUST be fully engaged and release buttons fully protruding out of same respective adjustment holes BEFORE use This will avoid a 3 Wheeling situation Anti tipper 2 Ensure that the release buttons are fully engaged in the adjustment Release Locking holes and l to 2 j inch clearance is maintained Button Button Wheelchair Frame 3 fal 2 2 ls inch clearance cannot be o
27. until wheel lock engagement holds the wheelchair Part No 1154295 85 Solara 3G Spree 3G Wheelchair DETAIL A Wheel Lock Mounting Bracket TOP VIEW Wheel Lock Assembly Socket Screws Socket Screws Behind Handle Wheel Lock Assembly Wheel Lock Wheel Lock Shoe dpa t at t Shoe FIGURE Wheel Lock Adjustment Push to Lock or Pull to Lock Wheel locks Footlock When changing the position of the rear wheels the wheel locks MUST be repositioned Before adjusting or replacing the wheel lock assemblies ensure that the tires are inflated to the recommended p s i on the side wall of the tire l Loosen but DO NOT remove the four mounting screws two mounting screws on each side that secure the wheel lock bracket to the wheelchair frame Detail 2 Measure the distance between the wheel lock shoe and the rear wheel Slide the wheel lock bracket along the wheelchair frame until the measurement between the wheel lock shoe and rear wheel is approximately 1 25 inches If 1 25 inch measurement is not achievable perform the following A Remove the mounting screw washers and locknut that secure the connecting wheel link to the footlock lever Detail B Solara 3G Spree 3G Wheelchair 86 Part No 1154295 Wheel Locks Anti Tippers B Slide the wheel lock bracket along the wheelchair frame until the measurement between the wheel lock shoe and rear wheel is approximately 1 25 inches
28. washer and 2 b Cantilever ocknut j Mn i Arm 4 Adjust the angle of the cantilever arm if necessary Refer to ewer Lex Adjusting Non Locking Cantilever Arm Angle page 62 Bolt Pe oS FIGURE 14 Installing Non Locking Cantilever Arms Adjusting Locking Cantilever Arm Height Part No 1154295 61 Solara 3G Spree 3G Wheelchair 10 ARMS Adjusting Non Locking Cantilever Arm Height l Remove the locknut and washer from the lower hex bolt securing the cantilever arm to the back cane 2 Slide the cantilever arm assembly out of the back cane Reposition the cantilever arm assembly to the desired mounting hole 4 Secure the cantilever arm to the wheelchair with a washer and locknut Adjusting Non Locking Cantilever Arm Angle I Loosen the mounting screw securing the cam to the cantilever arm 2 Rotate the cam until the desired angle is achieved Detail A 3 Tighten the mounting screw securing the cam to the cantilever arm Solara 3G Spree 3G Wheelchair Side View of Cam am Mounting Screw Back Cane N4 m D Back Cane DETAIL A CAM POSITIONS NOTE All arm angles are relative to the back cane Cantilever Arm 0 Arm Angle Back Cane Cam 4 Arm Angle 8 Arm Angle FIGURE 15 62 12 Arm Angle Angle 16 Arm Angle Adjusting Non Locking Cantilever Arm Part No 1154295 10 ARMS 10 10 Arm Pad Replacement for Cantilever Arms l Remove t
29. wheel locks DO NOT interfere with tires when rolling Ensure wheel lock pivot points are free of wear and looseness Ensure wheel locks are easy to engage Inspect axles to ensure they are free from dirt lint etc Inspect tilt slides and roller bearings to ensure they are free from dirt lint etc Inspect seat positioning strap for signs of wear Ensure buckle latches Verify hardware that attaches strap to frame is secure and undamaged Replace if necessary Solara 3G Spree 3G Wheelchair 30 Part No 1154295 6 SAFETY INSPECTION TROUBLESHOOTING Inspect Adjust Periodically Inspect clothing guards for bent or protruding metal Ensure that all fasteners on clothing guards are secure Ensure arms are secure but easy to release and adjustment levers engage properly Ensure that casters are free of debris Ensure adjustable height arms operate and lock securely Ensure armrest upholstery has no rips Ensure armrest pad sits flush against arm tube Ensure trigger release lever cables and handles return when released Ensure sealed bearings and axle nut tension are correct Inspect handrims for signs of rough edges or peeling finish Ensure seat back and or arm upholstery have no rips Clean upholstery and armrests Clean and wax all parts Check that all labels are present and legible Replace if necessary 2 Troubleshooting Mechanical ecoooocooOococoOOOCOOOCLO SOLUTIONS AND RATTLES
30. wheels are against the curb The wheelchair should be tilted back to the balance point and in one continuous upward movement the rear wheels should be pulled up and over the curb DO NOT return the front casters to the ground until the wheelchair has been pulled backward far enough for the front casters to clear the edge of the curb A WARNING When lowering the front casters of the wheelchair DO NOT let the wheelchair drop the last few inches to the ground This could result in injury to the occupant and or damage to the wheelchair Roll the wheelchair backward and slowly lower the wheelchair in one continuous movement DO NOT let the wheelchair drop the last few inches to the ground This could result in injury to the occupant FIGURE 5 5 Rotate the anti tippers so the anti tip wheels are pointing down Step Tube Solara 3G Spree 3G Wheelchair 26 Part No 1154295 5 SAFETY HANDLING OF WHEELCHAIRS 5 7 Stairways A WARNING ALWAYS wear your seat chest positioning strap Inasmuch as the SEAT CHEST POSITIONING STRAP is an option on this wheelchair You may order with or without the Seat Chest Positioning Strap Invacare strongly recommends ordering the Seat Chest Positioning Strap as an additional safeguard for the wheelchair user The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts if signs of wear appear strap
31. 22 104 18 TRANSPORT READY OPTION 107 About Transport Ready 4 2 108 Compliance Information oH a PR igcchsnudeusndadsnyasiaceashensbzsbasobessbusassadgstaupedececdbdaasaapodiatscbactassuaasuobedabacaaesh sods Uopedisbacdasessscansooceads 108 Specifications gm 108 Securing the Wheelchair to the Vehicle eese eene tentent asa trennt ttn tten aI ttn ten teen EE E SEa sentent 109 Securing the Occupant s sd e Ee e B E e e ee pede cem iet e t c bb A e 113 Solara 3G Spree 3G Wheelchair 5 Part No 1154295 GENERAL General Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage See the information below for definitions of the signal words DANGER Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both IMPORTANT Indicates a hazardous situation that could result in damage to property if it is not avoided Gives useful tips recommendations and information for efficient troub
32. E TERMS CONTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Part No 1154295 7 Solara 3G Spree 3G Wheelchair 2 SAFETY 2 Safety The safety section contains important information for the safe operation and use of this product 2 General Guidelines A WARNING DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner s manuals service manuals or instruction sheets supplied with this product or optional equipment If you are unable to understand the warnings cautions or instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur ACCESSORIES WARNINGS Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Check all parts for shipping damage and test before using In case
33. ED IN THE ATTACHMENT OF THIS LABEL AUCUN FAUTEUIL ROULANT NA T APPROUV POUR ETRE Refer to Owner s Manual for proper anti tipper 0 setting 1085379 Patent Label Solara 3G WEIGHT CAPACITY LIMITE DE POIDS 300 LBS 136 kgs NN 1 WARNING REFER TO OWNER S MANUAL d 3 DO NOT OPERATE WITHOUT SE REFERER AU MANUEL DE L UTILISATEUR THE ANTI TIP TUBES WEIGHT CAPACITY INSTALLED 60106Xx144 LIMITE DE POIDS 400 LBS 182 kgs REFERTO OWNER S MANUAL WEIGHT CAPACITY 8 SE REFERER AU MANUEL DE L UTILISATEUR A WA R N l N G LIMITE DE POIDS Sol 3G with Care must be taken so the configuration set up for 200 LBS 91 kgs olara wi the user is stable Stability adjustments must be REFERTO OWNER S MANUAL m SE REFERER AU MANUEL DE H eavy Duty performed by aqualified technician N 1074106 Detent balls should extend b id the tt f th af Spree 3G Package ONLY AWARNING tre ot ne axe REV 5 98 Part No 1154295 17 Solara 3G Spree 3G Wheelchair 3 PRODUCT LABELING 3 2 Wheelchairs with Transport Ready Option RS COMPLIES WITH ANSI RESNA 19 5 3 Refer to attached TRANSPORT READY OPTION Instruction Card and wheelchair Owner s Manual before use PIN 1120033 REV 08 05 Solara 3G Spree 3G Wheelchair 18 Part No 1154295 4 TECHNICAL DATA 4 Technical Data 4 Typical Product Parameters SOLARA 3G SPREE 3G OVERALL WIDTH
34. G Spree 3G Wheelchair I2 TILT 12 4 Positioning Tilt Locking Collars A WARNING Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury Anterior forward tilt is a feature of this wheelchair designed for the use of a healthcare professional or assistant only Engagement of the anterior forward tilt MUST NEVER be performed by the wheelchair user When anterior forward tilt is needed it MUST AL WAYS be engaged by a healthcare professional or assistant The back height seat depth back angle seating system tilt angle seat height size position of the rear wheels size position of the front casters as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the eleven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician DO NOT operate the wheelchair when the seat frame is in the anterior forward tilt position frame stops in the lower position and approximately 5 forward tilt Serious bodily injury may occur to the patient and the assistant s TO HEALTHCARE PROFESSIONALS ASSISTANTS Make sure the occupant of the wheelchair is properly positioned ALWAYS engage both wheel locks After any adjustments repair or service and before use make sure all attaching hardware is tightened securely and locking collars are positioned at the same position on the ti
35. HEELS 12 inches Pneumatic Standard 12 inch Pneumatic with flat free Optional 16 18 20 22 and 24 inch Pneu matic Urethane or Pneumatic with flat free Optional HANDRIMS Aluminum Handrims Plastic Coated Projection CASTER SIZE 6 x 2 inch with Precision Sealed Bearings Standard 8 inch with Precision Sealed Bearings Optional 4 1 5 1 linch with Precision Sealed Bearings Optional SEAT WIDTH 12 24 inches SEAT DEPTH SHORT FRAME 12 16 inches 12 16 inches MEDIUM FRAME 15 19 inches 15 19 inches LONG FRAME 18 22 inches BACK HEIGHT 17 20 inches Adjustable 20 or 24 inches Fixed WHEEL LOCKS TILT IN SPACE Push to Lock Standard or Pull to Lock Footlock Dual Cable Trigger Mechanism or Foot Pedal Mechanism Standard 5 to 50 of Tilt Solara 3G Spree 3G Wheelchair 20 Part No 1154295 RECLINER BACK 4 TECHNICAL DATA Dual Cable Trigger Mechanism Optional 0 175 of Tilt FRAME Steel WEIGHT LIMITATION Solara 3G 300 Ibs 136 kg Spree 3G 200 Ibs 91 Kgs Solara with Heavy Duty Package 400 Ibs 182 kg The seat to floor heights are based on pneumatic tires and pneumatic tires with flat free inserts If wheelchair is equipped with urethane tires subtract 1 4 inch from the measurements listed above All heights are measured with properly inflated new tires These heights can vary 1 4 inch due to tire wear Part No 1154295 21 Solar
36. MUST be replaced IMMEDIATELY DO NOT attempt to lift the wheelchair by any removable detachable parts Lifting by means of any removable detachable parts of a wheelchair may result in injury to the user or damage to the wheelchair Extreme caution is advised when it is necessary to move an occupied wheelchair up or down the stairs Invacare recommends that if possible the user be removed from the wheelchair prior to moving Invacare recommends using two assistants and making thorough preparations Make sure to use ONLY secure non detachable parts for hand hold supports Follow these instructions for moving the wheelchair between floors when an elevator is NOT available lf necessary rotate the anti tippers so the wheels are facing up 2 After the wheelchair has been tilted back to the balance point one assistant in the rear backs the wheelchair up against the first step while securely grasping a non removable non detachable part of the wheelchair for leverage 3 second assistant with a firm hold on a non detachable part of the framework lifts the wheelchair up and over the stair and steadies the wheelchair as the first assistant places one foot on the next stair and repeat STEP 4 wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway 5 f necessary rotate the anti tippers so the wheels are facing down WARNING ESCALATORS DO
37. Part No 1154295 39 Solara 3G Spree 3G Wheelchair Front Riggings 3 Retighten the two flat screws and locknuts The setting for positioning the footplate on the half clamp may vary for each footplate 4 Repeat STEPS 1 3 for opposite footplate if desired Angle Adjustment I Loosen but DO NOT remove the adjustment screw the half clamp Position the footplate to the necessary angle to accommodate the user Detail A Retighten the adjustment screw Torque to over 90 in Ibs but no more than 300 in lbs Repeat STEPS 1 3 for opposite footplate if desired 39 Screw or out until the adjustable angle flip up footplate is perpendicular to the footrest assembly or the desired inversion eversion is obtained 90 Footrest Support Flat Screws Footrest Support Footplate Te ye Detail Side 222 Footplate N View of Footplate and Footrest Support Kee 0 Footplate Half Clamp Hinge Adjustment Screw a 83 25 J Locknuts FIGURE 5 Adjusting Adjustable Angle Flip Up Footplates Solara 3G Spree 3G Wheelchair 40 Part No 1154295 9 5 Raising Lowering the Elevating Legrest Perform one of the following Raising Lift legrest assembly to desired height Lowering Lift elevating legrest assembly up with one hand While supporting the elevating legrest assembly and user s leg pull release lever up with other hand and lower legrest assembly to des
38. Reassemble the hex screw and coved spacer through the footrest upper support and mounting tube Solara 3G Spree 3G Wheelchair 36 Part No 1154295 Front Riggings 4 Securely tighten the hex screw and coved spacer 5 Install the footrest assembly onto the wheelchair Refer to Installing Removing Footrests on page 35 6 Repeat STEPS 1 5 for the opposite side of the wheelchair if necessary Footrest Upper Support Hex Screw Coved Spacer Mounting Tube Footrest FIGURE 2 Adjusting Footrest Height 60 70 and 70 Taper 70 MFX 90 70 LIFT and 90 LIFT Footrests Remove any accessories that are attached to the footrests Remove the socket bolt coved washer and locknut that secure the footplate to the footrest support Reposition the footplate to the desired height Son om Reinstall the socket bolt through the mounting holes of the footplate and footrest support A WARNING DO NOT overtighten socket bolt and locknut Footrest MUST be able to rotate upward from the horizontal to the vertical position 5 Secure the footplate to the footrest support with the coved washer and locknut Part No 1154295 37 Solara 3G Spree 3G Wheelchair Front Riggings Footrest Support Height Adjustment Holes Socket Bolt Footplate FIGURE 3 Installing Removing Footrests 70 90 70 LIFT and 90 LIFT Footrests 9 3 Installing Adjustable Angle Flip Up Footplate Hinge Position the adjustabl
39. SIZE WHEEL SIZE 2 SAFETY WHEEL LOCKS ANTI TIPPERS OCKING COLLAR TILT CABLES SEAT DEPTH x BACK ANGLE x x lt P SEATING SYSTEM SEATING SYSTEM x X X TILT ANGLE CASTER SIZE CASTER POSITION WHEEL SIZE WHEEL POSITION XI X XI X X X X X USER CONDITION SEAT HEIGHT Part No 1154295 X X X X X X lt X X X X X X Xx Solara 3G Spree 3G Wheelchair 2 SAFETY WARNING Stability All Models Except Recliners To maintain maximum stability position the rear wheel axle mounting brackets in the most rearward position Moving the rear wheels to any of the other mounting positions causes the wheelchair to decrease in stability If moving the rear wheel axle mounting brackets to any forward position ensure the wheelchair is stable before using ALWAYS ensure stability before using maximum amount of tilt in space or moving the rear wheel axle mounting brackets forward Test wheelchair before it is occupied by the end user to ensure safety Stability Recliner Models Only Before using any recline position of this wheelchair make sure the rear wheel axle mounting brackets are in the most rearward position in the axle mounting plate to maintain the stability of the wheelchair Do not change the handling maneuverability of the wheelchair by moving the rear wheel axle mounting brackets to any of the forward positions
40. Test wheelchair for maneuverability Readjust locknuts if necessary and repeat STEPS 1 3 until correct Snap dust cover into the caster headtube 05 ur oes 9 Repeat STEPS 1 5 for opposite side if necessary FIGURE 14 2 Adjusting Forks Solara 3G Spree 3G Wheelchair 84 Part No 1154295 Wheel Locks Anti Tippers 15 Wheel Locks Anti Tippers A WARNING After ANY adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 15 1 Wheel Lock Adjustment Push to Lock or Pull to Lock Wheel locks When changing the position of the rear wheels the wheel locks MUST be repositioned Before adjusting or replacing the wheel lock assemblies ensure that the tires are inflated to the recommended p s i located on the side wall of the tire l Loosen but DO NOT remove the two socket screws that secure the wheel lock assembly to the wheellock mounting bracket Measure the distance between the wheel lock shoe and the rear wheel Slide the wheel lock assembly along the wheel lock mounting bracket until the measurement is between 5 32 and 5 16 Securely tighten the two socket screws Repeat STEPS 1 4 for the opposite wheel lock Engage the wheel locks and push against the wheelchair to determine if the wheel locks engage the rear wheels enough to hold the wheelchair LAGS comico If the wheel locks DO NOT hold the wheelchair repeat STEPS 1 6
41. Y A WARNING DO NOT traverse climb or go down ramps or slopes greater than 9 NEVER leave the occupied wheelchair unattended at any time especially on an incline DO NOT attempt to reach objects if you have to move forward in the seat DO NOT attempt to reach objects if you have to pick them up from the floor by reaching down between your knees DO NOT lean over the top of the back upholstery seating system This will change your center of gravity and may cause you to tip over DO NOT shift your weight or sitting position toward the direction you are reaching as wheelchair may tip over DO NOT attempt to stop a moving wheelchair with wheel locks Wheel locks are not brakes DO NOT tip the wheelchair onto the rear wheels without assistance DO NOT use an escalator to move a wheelchair between floors Serious bodily injury may occur Before attempting to transfer in or out of the wheelchair every precaution should be taken to reduce the gap distance Turn both casters parallel to the object you are transferring onto When transferring to and from the wheelchair ALWAYS engage both wheel locks DO NOT use wheelchair unless it has the proper tire pressure p s i DO NOT overinflate the tires Failure to follow these suggestions may cause the tire to explode and cause bodily harm Recommended tire pressure is listed on the side wall of the tire DO NOT attempt to lift a wheelchair by lifting on any removable detachable parts Lifting by
42. a 3G Spree 3G Wheelchair 5 SAFETY HANDLING OF WHEELCHAIRS 5 Safety Handling of Wheelchairs Safety and Handling of the wheelchair requires the close attention of the wheelchair user as well as the assistant This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchair It is important to practice and master these safe techniques until you are comfortable in maneuvering around the frequently encountered architectural barriers Use this information only as a basic guide The techniques that are discussed on the following pages have been used successfully by many Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual Invacare recognizes and encourages each individual to try what works best for him her in overcoming architectural obstacles that they may encounter however ALL WARNINGS and CAUTIONS given in this manual MUST be followed Techniques in this manual are a starting point for the new wheelchair user and assistant with safety as the most important consideration for all 5 Stability and Balance A WARNING ALWAYS wear your seat chest positioning strap Inasmuch as the SEAT CHEST POSITIONING STRAP is an option on this wheelchair You may order with or without the Seat Chest Positioning Strap Invacare strongly recommends ordering the Seat Chest Positioning Strap as an additional safeguar
43. ailable by the auto industry Invacare cannot and does not recommend any wheelchair transportation system 18 2 Compliance Information This wheelchair conforms with the requirements of the ANSI RESNA WC Vol Section 19 Frontal Impact Test ANSI American National Standards Institute RESNA Rehabilitation Engineering and Assistive Technology Society of North America This wheelchair has been dynamically tested in a forward facing mode with the specified crash test dummy which corresponds to a person with a weight of 114 209 pounds restrained by BOTH pelvic and shoulder belts in accordance with ANSI RESNA WC Vol I Section 19 BOTH pelvic and upper torso belts should be used to reduce the possibility of head and chest impacts with vehicle components 18 3 Specifications Only wheelchairs which fit in the following size ranges should be occupied a motor 12 to 22 inches wide and 12 to 22 inches deep Weight Limit Solara 3G up to 300 pounds Solara 3G with Heavy Duty Package up to 400 pounds Solara 3G Spree 3G Wheelchair 108 Part No 1154295 18 TRANSPORT READY OPTION 18 4 Securing the Wheelchair to the Vehicle Positioning the Wheelchair in the Vehicle WARNING This wheelchair MUST be in a forward facing position during travel in a motor vehicle The recommended clear zones for wheelchair seated occupants restrained by BOTH pelvic and upper torso belt s and ONLY by a pelvic belt are shown in the diagr
44. ams and described below Frontal Clear Zones FCZ need to be LARGER when upper torso belt s are NOT used The rear clear zone of 16 is measured from the rearmost point an occupant s head The frontal clear zone is measured from the frontmost point on an occupant s head and is 26 inches with pelvic and upper torso belt s and 37 inches with ONLY a pelvic belt The frontal clear zone may not be achievable for wheelchair seated drivers The estimated seated height HHT from the ground or floor to the top of the wheelchair seated occupant s head ranges from approximately 47 inches for a small adult female to about 61 inches for a tall adult male Frontal Clear Zone 1615 4 FCZ Side View E N zm l n Frontal Clear Zone Top View Part No 1154295 109 Solara 3G Spree 3G Wheelchair 18 TRANSPORT READY OPTION Securement Points Tie Down Bracket Tie Down Brackets FIGURE Securement Points Solara 3G Spree 3G Wheelchair 110 Part No 1154295 18 TRANSPORT READY OPTION Securing the Wheelchair This wheelchair is to be used only with Wheelchair Tie down and Occupant Restraint Systems WTORS that have been installed in accordance with the manufacturer s instructions and SAE J2249 A copy of SAE 2249 Wheelchair Tie down and Occupant Restraint Systems WTORS for use in Motor Vehicles be obtained from SAE International 400 Commonwealth Drive Warrendal
45. back canes to the wheelchair frame 11 3 Adjusting the Back Angle Fixed Back Cane BACK SEAT Recliner Back Cane Back Cane Locknut S Back Height Adjustment CES Holes Back Height Adjustment Screw ix P ef U Locknut 2 FIGURE 2 Adjusting the Height of the Adjustable Height Back Canes Adjusting the Back Angle on Wheelchairs Equipped with Fixed Back Remove the mounting screw spacer and locknut that secures the inner and outer backrest mounting brackets together 2 Repeat STEP for the remaining back cane 3 Adjust the back to the desired angle by aligning the mounting hole of the inner bracket with the mounting hole of the outer bracket The available back angles are 90 95 100 105 110 115 120 Detail A Secure the inner and outer backrest mounting brackets together at the desire back angle with a mounting screw spacer and locknut Securely tighten 5 Repeat STEP 4 for the remaining back cane Part No 1154295 Solara 3G Spree 3G Wheelchair BACK SEAT DETAIL A AVAILABLE BACK ANGLES Spacer mae PON SL Mounting Outer Backrest Screw Mounting Bracket FIGURE 3 Adjusting the Back Angle on Wheelchairs Equipped with Fixed Back Solara 3G Spree 3G Wheelchair 66 Part No 1154295 BACK SEAT Adjusting the Back Angle on Wheelchairs Equipped with Fold Down Back Remove the mounting screw and locknut no
46. been changed to keep arm parallel to the ground floor Flip the cantilever arm up and out of the way Remove the locknut that secures the locking pin to the arm adjustment plate Determine the mounting hole in the arm adjustment plate that will be used to correspond to the back angle Securely tighten the locking pin and washer to the adjustment plate with a locknut Repeat STEPS 1 4 for the opposite side if necessary Arm Adjustment Plate Locking Pin Locknut Back Angle Bracket Arm Adjustment Plate 2 Arm Adjustment Back Angle Bracket Arm Adjustment Plate jjustment Plate Plate Q 2 FIGURE 13 Adjusting the Locking Cantilever Arm Angle 60 Part No 1154295 10 ARMS 10 9 Using Installing Adjusting Non Locking Cantilever Arms A WARNING DO NOT use lap trays with non locking cantilever arms Using Non Locking Cantilever Arms Pull the end of the cantilever arm down to lower the cantilever arm Back Cane 2 Pull the end of the cantilever arm up to move it out of the way Back Cane VA Coved Washers Installing Non Locking Cantilever Arms and Spacer Locknut ex Cantilever Arm Remove the locknut and washer from the lower hex bolt installed a 9 B on the non locking cantilever arm R b 5 2 Slide hex bolt of the cantilever arm assembly into the desired back ONG Wachee cane mounting hole SN 3 2 the cantilever arm to the wheelchair with a
47. btained contact a qualified technician Anti tipper Portion FIGURE 8 Installing Adjusting Anti Tippers eeled 4 Repeat STEPS 1 3 for opposite side Solara 3G Spree 3G Wheelchair 94 Part No 1154295 16 RECLINER BACK OPTION 16 Recliner Back Option A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may result The back height seat depth back angle seating system tilt angle seat height size position of the rear wheels size position of the front casters as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the eleven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician CAUTION DO NOT overtighten hardware attaching to the frame This could cause damage to the frame tubing 16 1 Recliner Operation A WARNING Both gas cylinders MUST be operational and adjusted properly before using the recliner DO NOT operate the recliner option if only one of the gas cylinders is operational or adjusted properly ALWAYS make sure that the wheelchair is stable in the full reclined back at 180 position and the full upright back at 90 position before using the recliner option Make sure the patient is properly positioned in the wheelchair before reclining or inclining sitting up to maintain maximum
48. cknut spacers and back cane 4 Securely tighten the seat positioning strap to the wheelchair with Coved the locknut Spacers 5 Repeat STEPS 1 4 for opposite side Replacing I Remove the hex screw locknut and seat positioning strap from the FIGURE 7 Installing Replacing Seat Positioning Straps back plate of the wheelchair frame 2 Discard existing seat positioning strap 3 Install the new seat positioning strap to the wheelchair Refer to Installing Replacing Seat Positioning Straps on page 69 Part No 1154295 69 Solara 3G Spree 3G Wheelchair BACK SEAT 11 7 Installing Replacing Chest Positioning Straps Installing Position the chest positioning strap to one of the holes on the back EN Back Cane cane gt The standard recommended position for the chest Locknut positioning strap is in the top hole of the back cane but may be mounted according to the user s needs Hex Screw 2 Secure the chest positioning strap to the back canes with the new existing hex screw and locknut 3 Repeat STEPS 1 2 for opposite side 22 Replacing Chest Positioning Strap 1 Remove the hex screw that secures the chest positioning strap to the back cane Z Discard existing chest p sitioning strap FIGURE 8 Installing Replacing Chest Positioning Straps 3 Repeat STEPS 1 2 for opposite side if necessary 4 Install the NEW chest positioning strap Refer to Installing Replacing Chest Positioning Straps
49. combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair OCCUPIED Proper positioning is essential for your safety When reaching leaning bending or bending forward it is important to use the casters as a tool to maintain stability and balance FIGURE 5 1 Stability and Balance Part No 1154295 23 Solara 3G Spree 3G Wheelchair 5 SAFETY HANDLING OF WHEELCHAIRS 5 2 Coping With Everyday Obstacles Coping with the irritation of everyday obstacles can be somewhat alleviated by learning how to manage your wheelchair Keep in mind your center of gravity to maintain stability and balance 5 3 Note to Wheelchair Assistants When assistance to the wheelchair user is required remember to use good body mechanics Keep your back straight and bend your knees whenever tilting wheelchair or traversing curbs or other impediments A WARNING DO NOT attempt to lift the wheelchair by any removable detachable parts Lifting by means of any removable detachable parts of a wheelchair may result in injury to the user or damage to the wheelchair Also be aware of detachable parts such as arms or legrests These MUST NEVER be used to move the wheelchair or as lifting supports as they may be inadvertently released resulting in possible injury to the user and or assistant s When learning a new assistance technique have an experienced assistant help you before attempting it alone 5 4 R
50. contracture platform left or right to the desired location 3 the locknut on the angle adjustment plate to secure the contracture platform in position Bi Lateral Contracture Footplate Contracture Platform Locknut Locknut Angle Adjustment Plate Adjustment Plate Bi Lateral Contracture Footplate Contracture Platform FIGURE 7 Contracture Assembly Width Adjustment Part No 1154295 105 Solara 3G Spree 3G Wheelchair 17 CONTRACTURE FOOT ASSEMBLY Replacing the Contracture Footplate Heel Loop Washers Mounting Screws Contracture This procedure applies to the bilateral contracture Footplate footplate only Tilt the contracture footplate forward to gain access to the mounting screws that secure the heel loop to the underside of the contracture footplate Refer to Adjusting the Angle of the Bilateral Contracture Footplate on page 100 Washers 2 Remove the four mounting screws and washers that secure the existing heel loop to the contracture footplate 3 Reverse STEPS 1 2 to install the new heel loop FIGURE 8 Replacing the Contracture Footplate Heel Loop Solara 3G Spree 3G Wheelchair 106 Part No 1154295 18 TRANSPORT READY OPTION 18 Transport Ready Option A WARNING Contact Invacare Corporation 800 333 6900 with any questions about using this wheelchair for seating in a motor vehicle When feasible wheelchair occupants should transfer i
51. ct loading Solara 3G Spree 3G Wheelchair 116 Part No 1154295 18 TRANSPORT READY OPTION Preferred Zone tt Optional Zone Side View The pelvic belt should be worn low across the front of the pelvis 2 Position the upper torso belt s over the shoulders 3 The belt s should not be held away from the body by wheelchair components or parts including but not limited to wheelchair armrests or wheels Refer to FIGURE 5 for proper and improper positioning of the belts 4 Ensure the belt s are not be twisted Adjust belts as firmly as possible being mindful of user comfort DO position belts INSIDE of armrests wheels etc DO NOT position belts OUTSIDE of armrests wheels etc FIGURE 5 Positioning Belts Part No 1154295 117 Solara 3G Spree 3G Wheelchair NOTES NOTES Solara 3G Spree 3G Wheelchair 118 Part No 1154295 NOTES NOTES Part No 1154295 119 Solara 3G Spree 3G Wheelchair Yes you can Invacare Corporation www invacare com USA One Invacare Way Elyria Ohio USA 44036 2125 800 333 6900 Canada 570 Matheson Blvd E Unit 8 2010 Invacare Corporation All rights reserved Republication Mississauga Ontario 147 4G4 Canada 800 668 5324 duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and 9 All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless oth
52. ct the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address on the back cover provide dealer s name address date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Do not return products to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THESE INSTRUCTIONS THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO TH
53. d for the wheelchair user The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts if signs of wear appear strap MUST be replaced IMMEDIATELY DO NOT CLIMB GO UP or DOWN ramps or traverse slopes greater than 9 Invacare strongly recommends proceeding down ramps or slopes slowly to avoid hard braking or sudden stops DO NOT leave elevating legrests in the fully extended position when proceeding down ramps or slopes Be aware that carrying heavy objects on your lap while occupying the wheelchair may adversely affect the stability of the wheelchair resulting in serious bodily injury to the user damage to the wheelchair and surrounding property This wheelchair has been designed to accommodate one individual If more than one individual occupies the wheelchair this may adversely affect the stability of the wheelchair resulting in serious bodily injury to the user and passenger and damage to the wheelchair and surrounding property Solara 3G Spree 3G Wheelchair 22 Part No 1154295 5 SAFETY HANDLING OF WHEELCHAIRS To assure stability and proper operation of your wheelchair you MUST at all times maintain proper balance Your wheelchair has been designed to remain upright and stable during normal daily activities as long as you DO NOT move beyond the center of gravity Virtually all activities which involve movement in the wheelchair ha
54. djusting the Back Angle eee Installing Removing Non Adjustable Stroller Handles Adjusting the Adjustable Angle Stroller Handles eee tee ten entente tentent tentent tette ttentent tenente ten teen ten tenente tentent ten Installing Replacing Seat Positioning Straps ete eeeee teen tentent ttt tente ten teen ttnttetttnee tentent tente Installing Replacing Chest Positioning 5 Installing and Removing a Seating 5 6 pad ee M 9 G 71 Adjusting Trigger Release Cables cre tt d ERU ER M REA RE ETERNA ee TRO AL E ERA 72 Adjusting FUBIO CK Cables T 75 Positioning Tilt Eocking Collars 2 nte et eed nie e ei aia eret ede aban edet ee t e te ER aa 76 nn 79 Adjusting the Vent Tray Height m n Installing Removing Rear Wheels Adjusting The Quick Release Axle Part No 1154295 4 Solara 3G S
55. e PA 15096 0001 877 606 7232 or 724 776 4970 Attach WTORS to the tie down brackets in accordance with the manufacturer s instructions and SAE J2249 Tilt Lock Out Ur ew h Tilt wheelchair until horizontal lines on tilt angle indicator are aligned with the dot on the rocker tube Refer to Engaging Tilt In Space on page 71 and Detail A in FIGURE 3 Pull release barrel out Detail Rotate tie down bracket counterclockwise Position mounting hole in tie down bracket on anchor pin Detail Repeat STEPS 2 4 for remaining tie down bracket Part No 1154295 EN Solara 3G Spree 3G Wheelchair 18 TRANSPORT READY OPTION Horizontal Lines DETAIL A Tilt Angle Indicator Rocker Tube Rocker Tube Tilt Angle Indicator DETAIL B DETAIL Tie Down E Bracket Tie Down Bracket Release Barrel FIGURE 2 Tilt Lock Out Solara 3G Spree 3G Wheelchair 112 Part No 1154295 18 TRANSPORT READY OPTION 18 5 Securing the Occupant Wheelchair Anchored Belts A WARNING The pelvic belt that is provided by Invacare has been tested for use in a motor vehicle on this wheelchair only DO NOT replace the pelvic belt with a different style pelvic belt The wheelchair has been provided with a pelvic belt which meets the requirements of ANSI RESNA WC I9 The pelvic belt provided by Invacare has been designed to accommodate use on either side of the vehicle If neces
56. e angle flip up footplate hinge on the footrest support tube at the desired height Position the hardware on the footrest support as shown in FIGURE 3 Flip the footplate hinge to the up position The footplate hinge will fall to the down position Tighten the socket screw and locknut that secure the footplate hinge to the footrest support until the footplate hinge remains in the up position Check the up and down motion of the footplate hinge to make sure the user of the wheelchair can operate the footplates easily DD ON Ur eG Te If the footplate s motion is too tight loosen the socket screw and locknut approximately JA turn tooloose tighten the socket screw and locknut approximately turn Solara 3G Spree 3G Wheelchair 38 Part No 1154295 Front Riggings Footrest Support Locknut Tube Footplate Hinge FIGURE 4 Installing Adjustable Angle Flip Up Footplate Hinge 9 4 Adjusting Adjustable Angle Flip Up Footplates WARNING When determining the angle of the footplates make sure the rear of the footplates DO NOT interfere with the movement of the front casters Otherwise injury or damage may occur Depth Adjustment l Remove the two flat screws and locknuts that secure footplate to the half clamp Observe the angle of the footplate for reinstallation 2 Move the footplate to one of four mounting positions If desired depth is still not obtained rotate the half clamp on the footplate hinge 180
57. eaching Leaning and Bending Forward A WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees Position the casters so that they are extended away from the drive wheels and engage wheel locks FIGURE 5 2 Reaching Leaning and Bending Forward Solara 3G Spree 3G Wheelchair 24 Part No 1154295 5 SAFETY HANDLING OF WHEELCHAIRS 5 5 Reaching Bending Backward A WARNING DO NOT lean over the top of the back upholstery This will change your center of gravity and may cause you to tip over Position wheelchair as close as possible to the desired object Position the casters so that they are extended away from the drive wheels to create the longest possible wheelbase Reach back only as far as your arm will extend without changing your sitting position FIGURE 5 3 Reaching Bending Backward 5 6 Tipping WARNING DO NOT tip the wheelchair without assistance When tipping the wheelchair an assistant should grasp the back of the wheelchair on a non removable non detachable part Inform the wheelchair occupant before tipping the wheelchair and remind him her to lean back Be sure the occupant s feet and hands are clear of all wheels and or pinch points After mastering the techniques of tipping the wheelchair use one of the following methods to tackle curbs short stairs etc Tipping Curbs Method Wheelchair with Step Tubes
58. eight Adjusting T Arm Width Solara 3G Spree 3G Wheelchair 54 Part No 1154295 Adjusting T Arm Depth Remove the two mounting screws that secure the arm pad to the arm tube Remove the two socket screws that secure the arm tube to the T Arm post Reposition the arm tube on the T Arm post A Desk Length Arms to one of three positions depending on the desired arm pad depth B Full Length Arms to one of five positions depending on the desired arm pad depth Two additional positions are obtainable by turning the arm tube 180 Re secure the arm tube to the T Arm post with the two socket screws Torque to 60 70 in lbs Reattach the arm pad to the arm tube with the two mounting screws Tighten securely Repeat for the opposite side if necessary Part No 1154295 55 Arm Pad Socket Screws Mounting Screw T Arm 10 ARMS Arm Tube Mounting Screw FIGURE 8 Adjusting T Arm Depth Solara 3G Spree 3G Wheelchair 10 ARMS 10 7 Adjusting T Arm Sockets Remove the rear wheels from the wheelchair if necessary Refer to Installing Removing Rear Wheels on page 81 Loosen but DO NOT remove the four hex screws and washers that secure T Arm socket to T Arm clamp Slide the T Arm into the T Arm socket until the locking lever is in the slot in the T Arm socket and an audible click is heard The T Arm socket will disassemble if the four hex screws and washe
59. erwise noted WD 40 is a registered trademark of the WD 40 Company Teflon is a registered trademark of E l Du Pont De Nemours and Company Loctite is a registered trademark of Loctite Corporation Part No 1154295 Rev B 2 10
60. est into the front and rear arm sockets 3 Flip armrest release lever to the locked vertical position Detail A 4 Install the quick release pin into the rear arm socket Repeat STEPS 1 4 for remaining flip back armrest if necessary Part No 1154295 10 ARMS Flip Back Armrest Front Arm Socket Rear Arm Socket Release Lever Quick Release Pin DETAIL A J R gt Unlock EE Position m ka p Horizontal SS osition Ss Vertical FIGURE 3 J Removing Installing Flip Back Armrest 49 Solara 3G Spree 3G Wheelchair 10 ARMS Using Armrest WARNING Make sure the locking mechanism is secured before using wheelchair Flip the armrest release lever to the unlocked position Detail A Pull the front of the flip back armrest straight up and out of the front arm socket and rotate towards the rear of the wheelchair li 2 3 Rotate the flip back armrest towards the front of the wheelchair and then downward into the front arm socket 4 Flip armrest release lever to the locked vertical position Detail A Flip Back Armrest Flip Back Armrest DETAIL A N Locked Position Vertical f S MU Front Arm Socket cor Unlock Position Horizontal Armrest Release Lever FIGURE 4 Using Armrest Solara 3G Spree 3G Wheelchair 50 Part No 1154295 10 ARMS 10 4 Replacing Conventional Armrest Pads Arret Pad l Remove the mounting screws that secure the existing armrest pad
61. he mounting screws from the armrest pad 2 Replace with NEW armrest pad 3 Secure with existing hardware Desk Length Arm Pads Full Length Arm Pads Arm Pad Armrest Pad Cantilever Arm Cantilever Cantilever Arm T Tide Slide Tube Mounting T NR Mounting Screws Screws FIGURE 16 Arm Pad Replacement for Cantilever Arms Part No 1154295 63 Solara 3G Spree 3G Wheelchair BACK SEAT Back Seat A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 11 1 Folding Unfolding the Back Assembly WARNING The back MUST be locked securely in place before using the wheelchair I Do one of the following Unfold Push pull the back towards rear of wheelchair until it locks in place e Fold Pick up on the back release levers and push the back towards the front of the wheelchair Release Levers FIGURE Folding Unfolding the Back Assembly Solara 3G Spree 3G Wheelchair 64 Part No 1154295 11 2 Adjusting the Height of the Adjustable Height Back Canes Fixed Back Cane Recliner Back Cane Both back canes should be adjusted to the same adjustment hole l Remove the back height adjustment screw and locknut that secure the back cane to the wheelchair frame 2 Adjust the back cane to the desired height adjustment hole 3 Reinstall the back height adjustment screw and locknuts that secure the
62. ired height Part No 1154295 41 Front Riggings Release Lever Elevating Legrest Assembly FIGURE 6 Raising Lowering the Elevating Legrest Solara 3G Spree 3G Wheelchair Front Riggings 9 6 Adjusting Footplate Height and Calfpad Height Depth Adjusting the Footplate Height I Loosen locknut and washer securing the slide tube to the elevating legrest 2 Reposition footplate to desired height securely tighten locknut and washer 3 If necessary repeat STEPS 1 2 to adjust remaining footplate height Adjusting Calfpad Height Loosen the mounting bolt and washer that secure the calfpad bracket to the elevating legrest assembly 2 Slidethe calfpad bracket up or down until the desired calfpad height is obtained 3 Tighten the mounting bolt and washer securing the calfpad bracket to the elevating legrest assembly 4 f necessary repeat STEPS 1 3 to adjust remaining calfpad bracket Adjusting Calfpad Depth Remove the mounting screw spacer and locknut that secure the calfpad to the calfpad bracket 2 Insert mounting screw through one of four calfpad bracket mounting holes 3 Using the mounting screw spacer and locknut secure the calfpad to the calfpad bracket 4 If necessary repeat STEPS 1 3 to adjust remaining calfpad assembly Solara 3G Spree 3G Wheelchair Calfpad Calfpad Bracket Mounting Bolt and Washer Elevating Legrest Assembl
63. is unoccupied To determine and establish your particular safety limits practice bending reaching and transferring activities in the presence of a qualified healthcare professional before attempting active use of the wheelchair ALWAYS wear your seat positioning strap The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear strap MUST be replaced IMMEDIATELY If the wheelchair is exposed to extreme temperature above 100 F or below 32 F high humidity and or becomes wet prior to use ensure handgrips DO NOT twist on the wheelchair handle otherwise damage or injury may occur ALWAYS check foam grips for looseness before using the wheelchair If loose contact a qualified technician for instructions The necessary back angle 90 95 100 105 110 115 120 MUST be selected before repositioning the rear wheels forward DO NOT operate the tilt in space if the trigger release levers and cables are not properly adjusted to ensure that the tilt in space is locked in place when engaged Pinch point may occur when returning the tilted seat to the full upright position Make sure the hands and body of the occupant attendants and bystanders are clear of all pinch points before returning the tilted seat to the full upright position Part No 1154295 13 Solara 3G Spree 3G Wheelchair 2 SAFET
64. lchair anchored or vehicle anchored belts Ensure quick release pins are engaged through bearing housings and tilt slides DO NOT alter or substitute wheelchair frame parts components or seating systems Part No 1154295 107 Solara 3G Spree 3G Wheelchair 18 TRANSPORT READY OPTION A WARNING A sudden stop and or collision may structurally damage your wheelchair Wheelchairs involved in such incidents should be replaced Only use the transport brackets included with TRRO and TRBKTS for the purposes described in this manual 18 1 About Transport Ready Packages TRRO includes four factory installed transport brackets and a wheelchair anchored pelvic belt TRRO has been crash tested in accordance with ANSI RESNA WC Vol Section 19 Frontal Impact Test requirements for wheelchairs with a 168 Ib crash dummy which corresponds to a person with a weight of 114 to 209 Ibs TRBKTS includes four factory installed wheelchair transport brackets TRBKTS has not been crash tested in accordance with WC 19 Invacare recommends that these transport brackets be used only to secure an unoccupied wheelchair during transport As of this date the Department of Transportation has not approved any tie down systems for transportation of a user while in a wheelchair in a moving vehicle of any type It is Invacare s position that users of wheelchairs should be transferred into appropriate seating in vehicles for transportation and use be made of the restraints made av
65. le free use Solara 3G Spree 3G Wheelchair 6 Part No 1154295 GENERAL 1 2 Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser user of our products This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants its product except for the seat cushion which is not warranted to be free from defects in materials and workmanship for a period of one year from the date of purchase when purchased new and unused from Invacare or an authorized provider The side frames and crossmembers are under a limited lifetime warranty from the date of purchase when purchased new and unused from Invacare or an authorized provider for the original purchaser user If within such warranty period this product shall be proven to be defective such product shall be repaired or replaced at Invacare s option with refurbished or new parts This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of this product Product repairs shall not extend this warranty coverage for repaired product shall end when this limited warranty terminates Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please conta
66. lt locking collar to the tilt slide Detail A 2 Repeat STEP for opposite side of wheelchair To determine tilt angle relative to the seat frame place a magnetic protractor available at any hardware store on the back and adjust the back until the magnetic protractor reads desired angle of tilt 3 Tilt the wheelchair to the desired angle of tilt 4 Position the two tilt locking collars against the bearing housing Before tightening ensure that the two tilt locking collars are at the same position on the tilt slide 5 Securely tighten the two set screws of the tilt locking collars Detail A DETAIL Tilt Slide Lower Tilt Locking Collar Bearing Housing FIGURE 5 Adjusting Lower Tilt Locking Collar Solara 3G Spree 3G Wheelchair 78 Part No 1154295 13 VENT TRAY 13 Vent tray 13 1 Adjusting the Vent Tray Height l Remove the two mounting screws and two locknuts that secure the front vent tray hanger bracket to the front cross tube Remove the four mounting screws eight washers and four locknuts that secure the rear vent tray hanger brackets to the wheelchair frame 3 Adjustthe vent tray to the desired height All three vent tray hanger brackets should be adjusted to the same height adjustment hole Secure the front vent tray hanger bracket to the wheelchair frame with two mounting screws and locknuts Tighten securely 5 Secure the rear vent tray hanger brackets to the wheelchair frame with
67. lt slide Adjusting Upper Tilt Locking Collar This procedure adjusts the degree of tilt that the wheelchair returns to for normal operation If the amount of tilt MUST be limited Refer to Adjusting Lower Tilt Locking Collar on page 78 l Loosen the set screw that secure the tilt locking collar to the tilt slide Solara 3G Spree 3G Wheelchair 76 Part No 1154295 I2 TILT 2 Repeat STEP for opposite side of wheelchair To determine tilt angle relative to the seat frame place a magnetic protractor available at any hardware store on the back and adjust the back until the magnetic protractor reads desired angle of tilt 3 Tilt the wheelchair to the desired angle of tilt The Solara seat frame is at a 5 back angle relative to the ground 4 Position the two tilt locking collars against the bearing housing Before tightening ensure that the two tilt locking collars are at the same position on the tilt slide 5 Securely tighten the two set screws of the tilt locking collars Bearing Housing Upper Tilt Locking Collar Set Screw Tilt Slide FIGURE 4 Adjusting Upper Tilt Locking Collar Part No 1154295 77 Solara 3G Spree 3G Wheelchair 12 TILT Adjusting Lower Tilt Locking Collar This procedure limits the amount of tilt the wheelchair may have If adjusting the angle the wheelchair returns to Refer to Adjusting Upper Tilt Locking Collar on page 76 Loosen the set screw that secures the ti
68. ludes top hex bolt coved washers and spacer between adjustment plate and cantilever arm 2 Slide the bottom hex bolt w coved washer through the adjustment plate and back cane 3 Securely tighten the cantilever arm to the wheelchair with two locknuts and washers 4 Adjust the angle of the cantilever arm if necessary Refer to Adjusting the Locking Cantilever Arm Angle on page 60 Solara 3G Spree 3G Wheelchair Part No 1154295 Adjusting Locking Cantilever Arm Height When removing the locknuts and washers from the cantilever arm assembly leave the top hex bolt coved washers and spacer between adjustment plate and cantilever arm in place 1 Remove the two locknuts and washers securing the cantilever arm assembly to the back cane 2 Remove the cantilever arm assembly with hardware from the back cane 3 Perform STEPS 1 4 in Installing Locking Cantilever Arms on page 58 to reposition the arm at the desired height Part No 1154295 10 ARMS Adjustment Plate Coved Washers lay Locknuts Washers Actuator Back Cane Bottom Hex Bolt Top Hex Bolt and Coved Washer Cantilever Arm FIGURE 12 Installing Locking Cantilever Arms Adjusting Locking Cantilever Arm Height 59 Solara 3G Spree 3G Wheelchair 10 ARMS Adjusting the Locking Cantilever Arm Angle UY ober OU NIS c Solara 3G Spree 3G Wheelchair This adjustment is recommended if the back angle has
69. nd body are clear of all pinch points Perform one of the following A For Hand Operated Tilt Detail i Stand behind the wheelchair and grasp both back canes firmly ii Pull up on the trigger release levers to release the tilt mechanism from the gear rack Part No 1154295 71 Solara 3G Spree 3G Wheelchair I2 TILT iii Slowly push down on the back canes while pulling up on the trigger release levers a continuous motion iv When the seat reaches the desired angle slowly let go of the trigger release levers B For Foot Operated Tilt Detail B i Push down on the foot lever to release the tilt mechanism from the gear rack ii Slowly push down the back canes while keeping the foot lever depressed iii When the seat reaches the desired angle release the foot lever DETAIL Trigger Release Lever DETAIL Bp Gear Rack Foot Lever Tilt Mechanism FIGURE Engaging Tilt In Space 12 2 Adjusting Trigger Release Cables WARNING DO NOT adjust the trigger release cables while the cables are coiled up The adjustment will be too tight when the cable is straightened and the tilt mechanism will not lock and hold its position possibly causing injury Solara 3G Spree 3G Wheelchair 72 Part No 1154295 I2 TILT This procedure applies to tilt in space release cables only To adjust the left tilt mechanism do the following A Squeeze the trigger release le
70. nto the vehicle seat and use the OEM Original Equipment Manufacturer vehicle installed restraint system This wheelchair has been dynamically tested in a forward facing mode with the specified crash test dummy restrained by BOTH pelvic and upper torso belt s shoulder belts and that BOTH pelvic and upper torso belt s should be used to reduce the possibility of head and chest impacts with vehicle components Use ONLY Wheelchair Tie down and Occupant Restraint Systems WTORS which meet the requirements of the SAE Society of Automotive Engineers 2249 Recommended Practice during travel in a motor vehicle This wheelchair has been tested for seating in a motor vehicle with the factory installed seating system only This wheelchair MUST be in a forward facing position during travel in a motor vehicle This wheelchair is equipped and has been dynamically tested to rely on WHEELCHAIR ANCHORED pelvic belts If desired VEHICLE ANCHORED pelvic belts may be used IT IS STRONGLY RECOMMENDED THAT BOTH PELVIC AND UPPER TORSO BELT S BE USED TO REDUSE THE RISK OF INJURY To reduce the potential of injury to vehicle occupants wheelchair mounted accessories including but not limited to IV poles trays respiratory equipment backpacks and other personal items should be removed and secured separately Postural supports positioning devices and or strap s should NOT be relied on for occupant restraint These items may be used IN ADDITION TO the whee
71. of damage DO NOT use Contact Invacare Carrier for further instruction Solara 3G Spree 3G Wheelchair 8 Part No 1154295 2 SAFETY A WARNING Wheelchair User As a manufacturer of wheelchairs Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end user However final selection of the type of wheelchair to be used by an individual rests solely with the user and his her healthcare professional capable of making such a selection Wheelchair Tie Down Restraints and Seat Positioning Straps TRRO or TRBKTS TRRO includes four factory installed transport brackets and a wheelchair anchored pelvic belt TRRO has been crash tested in accordance with ANSI RESNA WC Vol Section 19 Frontal Impact Test requirements for wheelchairs with a 168 Ib crash dummy which corresponds to a person with a weight of 14 to 209 Ibs TRBKTS includes four factory installed wheelchair transport brackets TRBKTS has not been crash tested in accordance with WC 19 Use these transport brackets only to secure an unoccupied wheelchair during transport Only use the transport brackets included with TRRO and TRBKTS for the purposes described in this manual As of this date the Department of Transportation has not approved any tie down systems for transportation of a user while in a wheelchair in a moving vehicle of any type It is Invacare s position that users of wheelchairs should be transferred into appropriate seating in vehicles for tran
72. om clamp with the two socket screws Screws 5 Install the T Arm onto the wheelchair Refer to Installing Removing T Arms on page 51 FIGURE 10 Adjusting T Arm Transfer Assists And or Side Guards Part No 1154295 57 Solara 3G Spree 3G Wheelchair 10 ARMS Using Installing Adjusting Locking Cantilever Arms Using Locking Cantilever Arms Push the locking mechanism actuator towards the front of the wheelchair 2 While holding the locking mechanism actuator pull up on the cantilever arm towards the rear of the wheelchair If necessary the locking mechanism in the cantilever arm can be repositioned so the cantilever arm will open down instead of up For this adjustment contact a qualified technician To lock the cantilever arm push down until there is an audible click 4 Pull up on the cantilever arm to make sure it is locked in place Installing Locking Cantilever Arms Ta Front of Wheelchair Rear of BM Wheelchair Push Locking Mechanism Actuator Cantilever Arm 7 FIGURE 11 Using Locking Cantilever Arms When removing the locknuts and washers from the cantilever arm assembly leave the top hex bolt coved washers and spacer between adjustment plate and cantilever arm in place the partially assembled cantilever arm assembly with mounting hardware through the back cane Make sure the adjustment plate is towards the inside of the wheelchair This inc
73. orizontal Arm Socket FIGURE Installing Removing Dual Point Armrests Fixed And Adjustable Height Part No 1154295 47 Solara 3G Spree 3G Wheelchair 10 ARMS 10 2 Adjusting the Height of the Adjustable Height Armrests 2 3 4 5 Unlock the armrest assembly by flipping the armrest release lever on the top front of the to the up horizontal position Detail A Adjust armrest assembly to desired height Lock the armrest assembly by pressing the release lever into the down vertical position Detail A Pull up on the armrest assembly to ensure the armrest is locked in place Repeat STEPS 1 4 for opposite side of wheelchair if necessary DETAIL A Locked Down i Vertical Horizontal Armrest Release Lever FIGURE 2 Adjusting the Height of the Adjustable Height Armrests Solara 3G Spree 3G Wheelchair 48 Part No 1154295 10 3 Removing Installing and Using Flipback Armrests Removing Installing Flip Back Armrest Removing l Flip the armrest release lever to the unlocked position Detail A 2 Pull the quick release pin out of the rear arm socket 3 Pull up on the flip back armrest to remove from the front and rear arm sockets 4 Repeat STEPS 1 3 for remaining flip back armrest if necessary Installing nsure that the armrest release lever is in the unlocke orizontal l E that th trel l th locked h tal position Detail A 2 Install flip back armr
74. otrest height Refer to Adjusting Footrest Height on page 36 or Adjusting Footplate Height Calfpad Height Depth on page 42 Removing Push the footrest release lever inward while rotating the front rigging outward 2 Lift the footrest assembly out of the mounting pin of the wheelchair frame 3 Repeat STEPS 1 2 for opposite side if necessary Only the swing away footrest is shown The lift off footrest assembly and elevating legrest install remove in the same manner Part No 1154295 35 Solara 3G Spree 3G Wheelchair Front Riggings Footrest Release Mounting Pin Lever diis Y A Footrest ounting Tube Ym Assembly Wheelchai LA Footplate Frame APN Only 60 Footrest shown for tLe clarity Others will attach the Willd same way FIGURE Installing Removing Footrests 9 2 Adjusting Footrest Height Height Adjustment Ranges 60 footrest Range 13 17 inches 70 footrest Range 13 17 inches 90 footrest Range 5 8 inches 90 footrest 5 11 inches with 3 inch extension If using ANY type of extension with the adjustable flip up footplate Refer to Adjusting Adjustable Angle Flip Up Footplates on page 39 60 70 and 70 Taper I Remove the footrest from the wheelchair Refer to Installing Removing Footrests on page 35 2 Remove the hex screw and coved spacer and slide the footrest up or down on its mounting tube until the desired footrest height is achieved 3
75. pree 3G Wheelchair CONTENTS Seat To Floor Height Adjustment cL LR 84 M sea 84 15 WHEEL LOCKS ANTI TIPPERS 85 Wheel Lock Adjustmentin enion re HEP NER UE ERE 85 Using the Wheel M 88 Operating Hublocks 92 Installing Adjusting Anti Tippers 5 5 Since acide e etd eee at deese al enden ie dete de eei e Ree once Ra eee idet cite do 94 16 RECLINER BACK 95 Recliner OI ril Me PU 95 Replacing Back Headrest Upholstery ierit tege eta dette oper Doe eee dtes eie edo tees tue ated 97 17 CONTRACTURE FOOT ASSEMBLY 99 Adjusting the Angle of the Contracture 2 99 Adjusting the Angle of the Bilateral Contracture Footplate e eese tentent tente ten tente ten ten tente 100 IBI pup 102 Contracture Footplate Height Adjustment 5 ertet estt bep 103 Contracture Assembly Width 44 4 22
76. r Wheels on page 81 Axle Mounting Rear Wheel Reference 2 Depress detent pin in the quick release axle and slide axle through the wheel hub Locknut 3 Increase or decrease end play in the quick release axle by adjusting the locknut on the end of the quick release axle Locking Pins 4 Reinstall rear wheel onto the wheelchair Refer to Installing m Removing Rear Wheels on page 81 Release detent pin ensuring that the locking pins are fully released Quick Release Axle Detent Pin Repeat STEPS 3 5 until the quick release axle locks properly Wheel Hub Repeat STEPS 1 6 for opposite side if necessary Reference FIGURE 14 1 Adjusting The Quick Release Axle Part No 1154295 83 Solara 3G Spree 3G Wheelchair 14 WHEELS FORKS 14 3 Seat To Floor Height Adjustment A WARNING Repositioning the axle plates seat to floor height MUST be performed by a qualified technician 14 4 Adjusting Forks l Remove the dust cover from the caster headtube 2 To properly tighten caster journal system and guard against flutter perform the following check back the wheelchair to floor EE B Pivot both forks and casters to top of their arc simultaneously Tn C Let casters drop to bottom of arc wheels should swing once to one side then IMMEDIATELY rest in a straight downward position Caster Headtube D Adjust locknuts according to freedom of caster swing
77. re Support Tube FIGURE Adjusting the Angle of the Contracture Assembly Solara 3G Spree 3G Wheelchair 17 CONTRACTURE FOOT ASSEMBLY 17 2 Adjusting the Angle of the Bilateral Contracture Footplate Adjusting the Side to Side Angle 2 3 4 Loosen the adjustment screw located underneath the contracture footplate See Detail A Tilt the contracture footplate left or right to the desired angle See Detail B Retighten the adjustment screw If necessary repeat STEPS 3 on remaining contracture footplate DETAIL A DETAIL B Contracture Footplate Adjustment Adjustment Contracture Screw Screw Footplate FIGURE 2 Adjusting the Angle of the Contracture Assembly Solara 3G Spree 3G Wheelchair 100 Part No 1154295 17 CONTRACTURE FOOT ASSEMBLY Adjusting the Front to Back Angle Loosen the adjustment screw located underneath the contracture footplate See Detail A l 2 the contracture footplate forward or back to the desired angle See Detail B 3 the adjustment screw 4 f necessary repeat STEPS 1 3 on remaining contracture footplate BEIM DETAIL B SIDE VIEW Contracture Footplate Adjustment Contracture Screw Footplate FIGURE 3 Adjusting the Front to Back Angle Part No 1154295 101 Solara 3G Spree 3G Wheelchair 17 CONTRACTURE FOOT ASSEMBLY 17 3 Depth Adjustment Bilateral Contracture Footplate PO UNI Remove the two flat screws and locknut
78. rear wheel away from the wheelchair frame If the locking pins do not engage or there is too much movement of the rear wheel assembly in a back and forth position Refer to Adjusting The Quick Release Axle on page 83 4 Repeat STEPS 1 3 for other rear wheel assembly Part No 1154295 8l Solara 3G Spree 3G Wheelchair 14 WHEELS FORKS 5 Adjust the wheel locks Refer to Wheel Lock Adjustment on page 85 Only 12 inch rear wheel is shown All other wheels will install remove in the same manner Rear MdL Locking PE Detent Pin SS Mounting Quick Release D Plate FIGURE I Installing Removing Rear Wheels Permanent Axle To remove rear wheels reverse this procedure 1 Remove the permanent axles from the packaged container 2 Install permanent axle through lock washer and the rear wheel and axle plate 3 Securely tighten the wheel to the wheelchair frame with locknut Only 12 inch rear wheel is shown All other wheels will install remove in the same manner Repeat STEPS 2 3 for other rear wheel assembly 5 Adjust the wheel locks Refer to Adjusting The Quick Release Axle on page 83 Solara 3G Spree 3G Wheelchair 82 Part No 1154295 14 WHEELS FORKS Rear Wheel Lockwasher o Permanent Axle FIGURE 2 Installing Removing Rear Wheels Permanent Axle 14 2 Adjusting The Quick Release Axle 1 Remove rear wheel and quick release axle from the wheelchair Plate Refer to Installing Removing Rea
79. rolled motion or spasms can result in damage to the hub lock system Engaging the hublocks may not prevent the wheelchair from moving on all floor surfaces including those that may be wet or slick ALWAYS exercise caution when transferring into or out of your wheelchair Always keep hands and fingers clear of moving parts to avoid injury DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails are fully seated into the side frame H blocks 15 3 Operating Hublocks If hublocks do not engage properly wheels move while hublocks are locked or do not disengage properly contact a qualified technician Patient Operated Hublock Perform one of the following Engaging the Hublocks Push hublock lever down to engage the hublocks Disengaging the Hublocks Pull hublock lever up to disengage the hublocks Solara 3G Spree 3G Wheelchair 92 Part No 1154295 Wheel Locks Anti Tippers Hublock Lever Unlocked Hublock Lever Up ocked Hublock Lever FIGURE 6 Patient Operated Hublock Attendant Operated Hublock 2 2 Locked Hublock Perform one of the following A Lever Up Engaging the Hublocks Push hublock lever up to engage the hublocks Disengaging the Hublocks Pull hublock lever down to disengage the hublocks Unlocked Hublock Lever Foot Operated Hublock DOWN Perform one of the following Unlocked Hublock Lever Engaging the Hublocks Press hublock pedal down
80. rs are removed Squeeze the T Arm socket and the T Arm clamp together until the socket is flush with the T Arm While holding the T Arm socket and the T Arm clamp together tighten the four hex screws and washers Tighten securely Press IN on the locking lever and lift the T Arm straight UP and out of the T Arm socket Repeat STEPS 3 6 if necessary until the T Arm slides in the T Arm socket as desired If necessary install rear wheels Refer to Installing Removing Rear Wheels on page 81 Solara 3G Spree 3G Wheelchair 56 Perform this procedure if the T Arm is too loose in the socket or does not easily slide UP and DOWN in the socket T Arm Clamp Hex Screws and Washers Hex Screws and Washers Slot T Arm Socket Locking Lever FIGURE 9 Adjusting T Arm Sockets Part No 1154295 10 ARMS 10 8 Adjusting T Arm Transfer Assists And or Side Guards l Remove the T Arm from the wheelchair Refer to Installing Removing T Arms on page 51 2 Remove the two socket screws that secure the side guard to the bottom clamp F Arm Adjusting the side guards will directly affect the B position of the transfer assist Transfer Assist 3 Perform one of the following Small Side Guards Move the bottom clamp UP to one of two mounting positions in the side guard Large Side Guards Move the bottom clamp UP to one of three mounting positions in the side guard 4 Secure the side guard to the bott
81. s that secure the contracture footplate to the footplate angle bracket Move the contracture footplate to one of four mounting holes Reinstall the four flat screws and locknuts that secure the contracture footplate to the footplate angle bracket Tighten securely If necessary repeat STEPS 1 3 on remaining contracture footplate Mounting Holes Contracture Footplate Flat Screws Locknuts Underneath Footplate Angle Bracket FIGURE 4 Depth Adjustment Bilateral Contracture Footplate Solara 3G Spree 3G Wheelchair 102 Part No 1154295 17 CONTRACTURE FOOT ASSEMBLY Contracture Platform l Remove the four flat screws that secure the contracture platform to the footplate angle bracket 2 Move the contracture platform to one of three mounting positions 3 Reinstall the four flat screws and locknuts that secure the contracture platform to the footplate angle bracket Tighten securely Mounting Holes Contracture Platform Flat Screws Footplate Angle Bracket FIGURE 5 Depth Adjustment Contracture Platform 17 4 Contracture Footplate Height Adjustment Bilateral Contracture Footplate Remove the mounting bolt two coved washers washer and locknut that secure the footplate bracket to the contracture support Move the footplate bracket up down to achieve desired height Align one of the mounting holes in the footplate bracket with one of the seven mounting holes on the contracture support Secure the footplate bracke
82. s to a stop Ensure wheel fork assembly has proper tension when caster is spun Caster should come to a gradual stop Part No 1154295 29 Solara 3G Spree 3G Wheelchair SAFETY INSPECTION TROUBLESHOOTING Loosen tighten caster locknut if wheel wobbles noticeably or binds to a stop Ensure all caster wheel fork headtube fasteners are secure Ensure that casters are free of debris 6 Q m m Q Ensure wheel locks DO NOT interfere with tires when rolling Ensure wheel lock pivot points are free of wear and looseness Ensure wheel locks are easy to engage Inspect tires for flat spots and wear Q Check pneumatic tires for proper inflation C Check that all labels are present and legible Replace if necessary Inspect Adjust Weekly Ensure wheelchair rolls straight no excessive drag or pull to one side Ensure hand grips are not loose Ensure wheel fork assembly has proper tension when caster is spun Caster should come to a gradual stop Ensure all caster wheel fork headtube fasteners are secure Ensure that casters are free of debris D CO CO DO UOCU Check pneumatic tires for proper inflation Inspect Adjust Monthly Ensure sealed bearings and axle nut tension are correct Ensure there is no excessive side movement or binding when drive wheels are lifted and spun Adjust bearing system if wheel wobbles noticeably or binds to a stop Inspect tires for flat spots and wear Ensure
83. sary follow the instructions below to reverse the orientation of the pelvic belt to accommodate the vehicle anchored upper torso belt Install the pelvic belt pin Detail A of FIGURE 3 into slot in the pelvic belt bracket Pull upwards until it snaps into place Note the position of the male end of the belt when installing the pelvic belt onto the pelvic belt brackets The male end of the pelvic belt Detail A of FIGURE 3 has a pin which is used to secure the vehicle anchored upper torso belt 2 Repeat STEP for the opposite pelvic belt bracket 3 Install the vehicle anchored upper torso belt onto the pin on the male end of the pelvic belt Part No 1154295 113 Solara 3G Spree 3G Wheelchair 18 TRANSPORT READY OPTION Pin DETAIL A PELVIC BELT Pelvic Belt Bracket Pin Pelvic Belt Pu t Used to secure the vehicle anchored upper torso belt Tie Down 2 L o Bracket Q FIGURE 3 Wheelchair Anchored Belts Solara 3G Spree 3G Wheelchair 114 Part No 1154295 I8 TRANSPORT READY OPTION Vehicle Anchored Belts This wheelchair has an overall rating of B with regard to accommodating the use and fit of vehicle anchored belts This rating is scored as follows DESCRIPTION Excellent Good Fair The test for Lateral Stability Displacement for Point P is shown in FIGURE 4 The average test result for point P is 0 65 inches 16 5 mm Rear View f Point P
84. sert bolt through the back cane and stroller handle Secure the stroller handle to the back cane with the bolt and nut 22 Locknut gxour e UU Pull on the stroller handle to make sure it is locked securely in Mounting Holes place Removing Stroller Handles i N Back Cane l Remove the locknuts that secure the stroller handle to the back li 2 Pull out the bolts that secure the stroller handle to the back canes FIGURE 5 Installing Removing Non Adjustable Stroller 3 Remove the stroller handle from the wheelchair Handles 11 5 Adjusting the Adjustable Angle Stroller Handles Press and hold in both buttons on the outside of the hinge arm of the stroller handle Adjust stroller handle to desired angle 2 3 Release the buttons 4 Push down on stroller handle to ensure hinge arms hold the desired position of the stroller handle There will be an audible click If hinge arms do not hold the position contact Invacare technical support Solara 3G Spree 3G Wheelchair 68 Part No 1154295 BACK SEAT Stroller Handle Hinge Arm FIGURE 6 Adjusting the Adjustable Angle Stroller Handles 11 6 Installing Replacing Seat Positioning Straps Installing Back Plate Back Cane Remove the hex screw and locknut that secures the back cane to the back plate 2 Position the seat positioning strap against the back plate 3 Install the hex screw through the seat positioning strap coved Lo
85. sportation and use be made of the restraints made available by the auto industry Invacare cannot and does not recommend any wheelchair transportation systems Refer to Transport Ready Option on page 107 for more information about transporting the wheelchair Only use the transport brackets included with TRRO and TRBKTS for the purposes described in this manual ALWAYS wear your seat positioning strap Inasmuch as the seat positioning strap is an option on this wheelchair you may order with or without the seat positioning strap Invacare strongly recommends ordering the seat positioning strap as an additional safeguard for the wheelchair user The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear strap MUST be replaced IMMEDIATELY Part No 1154295 9 Solara 3G Spree 3G Wheelchair 2 SAFETY WARNING With regards to seat chest positioning straps it is the obligation of the DME dealer therapists and other healthcare professionals to determine if a seat chest positioning strap is required to ensure the safe operation of this equipment by the user Serious injury can occur in the event of a fall from a wheelchair Information for Healthcare Professionals Assistants The Solara wheelchair MUST be operated by a healthcare professional or assistant when in any tilt position Anterior Forward Tilt
86. t chair width adjustment or seating accommodation cables MUST be readjusted Part No 1154295 73 Solara 3G Spree 3G Wheelchair I2 TILT DETAIL A Cable Locking Nut Gear Sector If there is a gap between the top of the gear rack teeth and the bottoms of the gear sector teeth the gear sector is not Cable fully engaged Adjusting Nut Gear Rack Gear Assembly FIGURE 2 Adjusting Trigger Release Cables Solara 3G Spree 3G Wheelchair 74 Part No 1154295 12 3 Adjusting Hublock Cables A WARNING DO NOT adjust the hublock cables while the cables are coiled up The adjustment will be too tight when the cable is straightened and the tilt mechanism will not lock and hold its position possibly causing injury Lift up on the hublock lever to test the hublock If the cable is too loose the hublock will not work 2 Perform one of the following A Loosen the cable locking nut that secures the cable adjusting nut in place Turn cable adjusting nut one of two ways ToTighten Turn the cable adjusting nut clockwise DO NOT overtighten the cable adjusting nut FIGURE 2 To Loosen Turn the cable adjusting nut counterclockwise FIGURE 2 While holding the cable adjusting nut in place tighten the cable locking nut against the cable adjusting nut Part No 1154295 75 FIGURE 3 Nut I2 TILT Hublock Lever DETAIL A Adjusting Hublock Cables Solara 3
87. t shown that secures the backrest brackets to the adjuster plates and adjuster spacer One adjuster plate and one backrest brackets are located on each side of the adjuster spacer 2 Repeat STEP for the remaining back cane 3 Adjust the back to the desired angle by aligning the mounting hole of the adjuster plates and adjuster spacer with the mounting hole of the backrest brackets The available back angles 90 95 100 105 110 115 120 Detail A 4 Secure the backrest brackets to the adjuster plates and adjuster spacer at the desired back angle with a mounting screw and locknut Securely tighten 5 Repeat STEP 4 for the remaining back cane Adjuster Plate Locknut Not Shown Mounting Screw Backrest Bracket Adjuster Spacer aA FIGURE 4 Adjusting the Back Angle on Wheelchairs Equipped Part No 1154295 Adjuster Adjuster Spacer Plate Backrest DETAIL A Bracket EN 90 E 100 25 105 110 1209 15 with Fold Down Back 67 Solara 3G Spree 3G Wheelchair BACK SEAT 11 4 Installing Removing Non Adjustable Stroller Handles Installing Stroller Handles Remove plug buttons from both back canes if necessary 4 Install the new stroller handle if desired Refer to Installing Stroller Slide stroller handle into the back canes Handles on page 68 Align the mounting holes of the stroller handle and the back canes Stroller Handle In
88. t to the contracture support with the mounting bolt two coved washers washer and locknut Securely tighten epe Ge 2 If necessary repeat STEPS 4 on remaining contracture footplate Part No 1154295 103 Solara 3G Spree 3G Wheelchair 17 CONTRACTURE FOOT ASSEMBLY Contracture Platform I Loosen but DO NOT remove the two mounting bolts and locknuts that secure the contracture platform to the upper support 2 Slide the contracture platform to the desired height 3 Tighten the two mounting bolts and locknuts that secure the contracture platform to the upper support Contracture Bilateral Contracture Footplate Contracture Platform Mounting Support Holes Upper Support Mounting P Bolt Locknut Washer 5 A No Coved Locknut amp Wash r Mounting Footplate bolt Mounting Bracket Holes Contracture Platform FIGURE 6 Contracture Footplate Height Adjustment 17 5 Contracture Assembly Width Adjustment Bi lateral Contracture Footplate l Loosen the locknut on the angle adjustment plate 2 Slide the contracture assembly left or right to the desired location 3 the locknut on the angle adjustment plate to secure the contracture footplate in position 4 Repeat STEPS 1 3 for remaining footplate if desired Solara 3G Spree 3G Wheelchair 104 Part No 1154295 17 CONTRACTURE FOOT ASSEMBLY Contracture Platform Loosen the locknut on the angle adjustment plate 2 Slide the
89. tenen tten teen ttntte tentent ten tentent teniente 38 Adjusting Adjustable Angle Flip Up Footplates Raising Lowering the Elevating Legrest 5 2 tree ettet e Het Rete tiia fre UR nette bibere RR dedere ba Ee apo de Adjusting Footplate Height and Calfpad Height Depth eterne tenente tentent tenente tentent tente ten tente tten 42 Composite Articulating Footplate Heel Loop 4 43 Replacing Bolt On Sector Block nee t pet eei T e ttc ed i eo o to e t o onte p de eae a ane 44 Replacing Glamp on Sector Bloeck ee ERR Ge ER eter bett ies 44 Installing Impact Guards Calf Strap H Calf 2 45 10 H 46 Installing Removing Dual Point Armrests Fixed And Adjustable Height ssccsssssssssssssssssssesssessssssssesssesssessseesssesssesssesssesssesssessnsssssessesssessseesseesseessneess 46 Adjusting the Height of the Adjustable Height Armrests eterne entente tenen tten tentent tenent ten teen tent tette tenn tentent tentent ten teen ten teen tenteentennenn 48 Removing Installing and Using Flipback
90. to the armrest assembly 2 Install new armrest pad and securely tighten with the existing Armrest mounting screws Assembly 24220 Mounting Screws FIGURE 5 Replacing Conventional Armrest Pads 10 5 Installing Removing T Arms Installing T Arms Position the T Arm over the T Arm socket on the wheelchair frame Make sure the locking lever is towards the front of the wheelchair 2 Slide T Arm into T Arm socket until the locking lever is in the slot in the T Arm socket and an audible click is heard 3 Pull up on T Arm to make sure T Arm is locked in place If the T Arm does not slide in the T Arm socket as desired adjust the T Arm socket Refer to Adjusting T Arm Sockets on page 56 4 Adjust the T Arm for desired height width and depth if necessary Refer to Adjusting The T Arms on page 53 Repeat STEPS 1 4 for opposite side of wheelchair Part No 1154295 51 Solara 3G Spree 3G Wheelchair 10 ARMS T Arm Locking Lever towards the front of the wheelchair Wheelchair Frame Slot T Arm 7 Socket FIGURE 6 Installing Removing T Arms Removing T Arms Press the locking lever in and lift the T Arm straight up and out of the T Arm socket If the T Arm does not slide in the T Arm socket as desired adjust the T Arm socket Refer to Adjusting T Arm Sockets on page 56 2 Repeat STEP for opposite side of the wheelchair Solara 3G Spree 3G Wheelchair 52 Part No 1154295 10 ARMS
91. ve an effect on the center of gravity Invacare recommends using seat chest positioning straps for additional safety while involved in activities that shift your weight DO NOT lean forward out of the wheelchair any further than the length of the armrests Make sure the casters are pointing in the forward position whenever you lean forward This can be achieved by advancing the wheelchair and then reversing it in a straight line The Invacare Solara 3G Spree 3G wheelchair should be operated by an assistant when the wheelchair is in any tilted position A WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees The back height seat depth back angle seating system tilt angle seat height size position of the rear wheels size position of the front casters as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the eleven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician Many activities require the wheelchair user to reach bend and transfer in and out of the wheelchair These movements will cause a change to normal balance center of gravity and weight distribution of the CENTER OF wheelchair To determine and establish your particular safety limits GRAVITY practice bending reaching and transferring activities in several
92. ver of the right cable assembly FIGURE on page 72 B Check that the teeth of the right gear sector engage with the gear rack Detail B in FIGURE 2 on page 74 C Try to tilt the wheelchair The wheelchair should not tilt 2 Ifthe left side of the wheelchair tilts without squeezing the trigger release lever of the left cable assembly or if the gear sector is not fully engaged with the gear rack perform the following steps A Loosen the cable locking nut that secures the cable adjusting nut in place B Turn cable adjusting nut one of two ways If the cable is too loose the tilt mechanism will not work Ifthe cable is too tight the gear sector will not be fully engaged with the gear rack A WARNING DO NOT over tighten the cable adjusting nut on the cable Over tightening the cable adjusting nut on the cable WILL unlock the tilt mechanism possibly causing injury To Tighten Turn the cable adjusting nut clockwise DO NOT overtighten the cable adjusting nut To Loosen Turn the cable adjusting nut counterclockwise C While holding the cable adjusting nut in place tighten the cable locking nut against the cable adjusting nut D Repeat STEP E Repeat STEP 2 until the left side of the wheelchair does not tilt and that the gear sector fully engages with the gear rack 3 If necessary repeat STEPS and 2 to adjust the left trigger release lever A WARNING When cables have been rerouted due to seat depth adjustmen
93. y Mounting Screw Locknut and Washer Slide Tube Calfpad Bracket Mounting Holes Locknut Footplate FIGURE 7 Adjusting Footplate Height and Calfpad Height Depth Part No 1154295 9 7 Composite Articulating Footplate Heel Loop Replacement Disassembly Composite Remove the hex screw and coved spacer that secure the lower footrest assembly to the swing away footrest assembly 2 Remove the lower footrest assembly 3 Remove the phillips screw and locknut that secure the heel loop to the footrest 4 Slide heel loop off of the footrest Articulating Remove the phillips screws washers and spacers that secure the heel loop to the articulating footplate Reassembly l 2 Part No 1154295 Replace heel loop Reverse the disassembly procedures When securing the heel loop to the footrest assembly tighten phillips screw until the spacer is secure 43 Front Riggings Composite Footplate Swingaway Footrest Assembly Phillips Hex Screw and Coved Screws Phillips Spacer Screw Lower Footrest Washer Assembly Spacer Heel Loop Articulating Locknut Footplate FIGURE 8 Composite Articulating Footplate Heel Loop Replacement Solara 3G Spree 3G Wheelchair Front Riggings 9 8 l 9 9 Solara 3G Spree 3G Wheelchair Replacing Bolt On Sector Block Remove the mounting screw and washer that secure the existing sector block to the front

Solara 3G/ Spree 3G Wheelchair

Contents

Download Pdf Manuals

Related Search

Related Contents