3 MB 2nd May 2013 DN5241 Manual
Contents
1. Power LED When power is properly connected the LED illuminates 1 2 Ultra Low Light High Resolution Camera dz 2 1 2 Ultra Low Light High Resolution Camera B installation Procedures 3 Remove the cover of the Auto Iris Lens connector plug and solder the lens cable to the connector pins of the plug For a Video Drive Lens For a DC Drive Lens Pin 1 Red Power Pin 1 Damping Pin 2 NC Pin 2 Damping Pin 3 White Video Signal Pin 3 Drive Pin 4 Black Ground Pin 4 Drive Et Lens f No 3 Pin T connector R No 1 Pin NS YS No 4 Pin No 2 Pin 4 Fit the cover of the auto iris lens connector plug remove the protective CCD cover from the front of the camera and fasten the Auto Iris Lens by turning it clockwise 5 Focus the camera using the Auto Iris Lens controls combined with fine adjustment using using the Back Focus control 1 2 Ultra Low Light High Resolution Camera NL Using a C CS mount Lens Before installing a lens identify whether the lens to be installed is a C Mount or CS Mount This camera is set for a CS Mount Lens by default To install a C Mount Lens a simple modification is required When Using a CS Mount Lens Remove the protective cover from the front of this product and turn the CS Mount Lens clockwise to install it Focus the camera using the CS Mount Lens and Back Focus controls e Use a lens threaded as shown in the following figur2. BAUD RATE INT AUTO 1 2 Ultra Low Light High Resolution Camera N22 SWITCH SET ON or OFF of OSD MENU X t becomes a decision at the title screen UP DOWN UP or DOWN of Cursor LEFT RIGHT SUB MENU ON or Decision x When OSD MENU is OFF and PAN TILT is ON operate by UP DOWN LEFT RIGHT MOTION DETECT becomes invalid while moving PAN TILT MAIN MENU MENU b EXPOSURE t WHITE BAL DAY NIGHT Tee MOTION Tee PRIVACY F OPTION DISPLAY Tee SYNC AUTO INITIAL NOT USE EXIT EXPOSURE WHITE BAL DAY NIGHT MOTION PRIVACY OPTION and DISPLAY has a SUB MENU UP DOWN of Cursor And SUB MENU is displayed by LEFT RIGHT SYNC AUTO or INT can be selected When making INITIAL from USE to NOT USE all data is initialized Xx It doesn t operate at NOT USE EXIT is non displayed by LEFT RIGHT 2 _ 7 2 Ultra Low Light High Resolution Camera _ E Camera Operation EXPOSURE WHITE BALANCE EXPOSURE WHITE BAL b LENS DC b WB MODE ATW NDS d 3 RED CONT NOT USE SHUTTER NOT USE BLUE CONT NOT USE AGC MID PUSH AUTO NOT USE SENSE UP X2 ECLIPSE OFF RETURN y DNR ON RETURN WB MODE ATW AWC MANUAL can be selected LENS ELC or DC VIDEO can be selected RED CONT ib it E iih a a can be selected BRIGHTNESS 0 to 60 can be selected nother becomes BACKLIGHT OFF or ON can be selected BLUE CONT
3. 189 NTSC or 2 to 187 PAL can be selected RETURN It returns to the MAIN MENU OPTION OPTION gt TITLE 3E NEGA POSI POSI SHARPNESS 7 MIRROR NOMAL ZOOM OFF PAN TILT OFF PHASE 0 RETURN 25 1 2 Ultra Low Light High Resolution Camera _ Mi Camera Operation E POSITION TITLE TITLE is displayed NEGA POSI NEGA or POSI can be selected SHARPNESS 0 to 15 can be selected TEE PEE MIRROR NORMAL MIRROR VERTICAL ROTATE can be selected ZOOM OFF x1 and ON1 to ON8 x4 can be selected When PAN TILT is ON itis NOT USE PAN TILT OFF or ON x2 can be selected x When OSD MENU is OFF and PAN TILT is ON operate by UP DOWN TITLE no LEFT RIGHT PHASE You can select a desired phase between 0 and 524 when the SYNC menu is fixed to the AUTO mode RETURN It returns to the MAIN MENU TITLE position is changed by UP DOWN LEFT RIGHT MENU is returns to the TITLE B TITLE TITLE DISPLAY lt BS POS END ABCDEFGHIJKLM DISPLAY BG US we P Orr gt TITLE OFF abcdefghijklm MOTION DET OFF 0 O23 45 657 8 9 BAUD RATE 9600 RETURN TITLE OFF or ON can be selected moves Dy IVE DOWN LEFT and RIGHT MOTION DET OFF or ON can be selected Character is setting by MENU The character from 1 to 10 can be set When MENU is pushed by can move between the set characters CAMERA ID Determi
4. 286Vp p Burst Level 0 286Vp p S N 50dB Min AGC Correct Off Sensitivity 0 08Lux Colour 0 01Lux B W 0 001Lux Sens up F1 2 Sense UP Max 32 times Correction 0 45 AGC 18dB Max IRIS Control Electrical IRIS Lens IRIS DC Lens Electrical Shutter 1 60 1 50 1 120 000sec Power Supply Voltage AC230V Power Supply Current MAX 4 5W Operating Temperature 10 C 50 C Operating Humidity 90 RH max Weight 320g 1 2 Ultra Low Light High Resolution Camera N32 Genie YZ COTY GENIE CCTV LTD CCTV House City Park Watchmead Welwyn Garden City Hertfordshire AL7 ILT Tel 44 0 1707 330541 Fax 44 0 1707 330543 www geniecctv com f Genie LZ Model 035241 1 2 Ultra Low Light High Resolution Camera Instruction Guide
5. IN Port DS T ERE Connections for Camera power as specified for each model amp Rear View Lens S The lens is not supplied with this camera Purchase a lens suitable for the environment This camera accepts an auto iris lens and both C and CS mount lenses 9 6 OSD Setup Buttons SET Button Displays the menu on the screen Press this button to confirm status or after changing a selected item Up and Down Button Used to move the cursor up or down in the menu Keep the lens surface clean as the picture quality suffers if screen to select a desired menu item there is dirt or fingerprints on the Lens Left and Right Button Used to move the cursor left or right in the menu screen or to change the value of the selected item 7 D amp N Input Port GND Colour Open B W Switch to Day or Night Mode by connecting an external signal to this port MD Output Port Motion detection signal is output through this port e It is recommended to use the DC type Auto Iris Lens to effectively enjoy the major functions of this camera Using an Auto lris Lens 1 Strip 8mm of insulation from the end of the Auto Iris Lens cable 4 0V 4 5V less than 10mA OV There is motion There is motion 12a w 9 RS 485 Control Port The SETUP MENU can be controlled via this port using an external controller that supports RS 485 communications For details see page 19
6. could void the user s authority to operate the equipment CAUTION To prevent electric shock and risk of fire hazards Do NOT use power sources other than those specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes 1 2 Ultra Low Light High Resolution Camera Contents Features o OZ 04 ee 20 errena a a a a a AE eae A Aaa EIE REAR SAET EENAA 20 ES a E 21 Components and Accessories AD dp LUE 08 B MAIN MENU 21 EXPOSURE ADU Ov o o o 0 0 0 0 0000 0 000 0 0008008 8 5008008 09 UUBITE BALANCE uuo chess btw treni et dorado dett List 23 M Front VIGW AY te edle Mesas tte i tienen Ga Side View e 10 24 Bottom View sss ei cinta Pn coste ero dhe pd Rd EAR iD tcc deca eti decd US di fe rag 11 PRIVACY 25 ENSIS EQ ILLI 12 OPON eere A E nese ee 25 T DISPLAY e tied exte brisa d qi neg dard kd Denia i cui lena 207 Installation Procedures EE Es EER ae i cd PE T TEE 28 pM 13 28 Using an Auto Iris Lens Using C CS mount Lens E Connecting a Monitor 17 Troubleshooting mn 29 Connecting POWO rp Her
7. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules amp CE Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer
8. Camera 2 Auto Iris Lens Connector Plug 3 C Mount Adapter Tripod Mounting Bracket Screw Hole Used to fix the Tripod Mounting Bracket to the top of the camera 2 C Mount Lens Adapter Install this adapter to use a C Mount Lens 3 Back Focus Control Lever Adjust Back Focus using this control lever 4 Instruction Manual 1 2 Ultra Low Light High Resolution Camera es 1 2 Ultra Low Light High Resolution Camera B Overview Side View Bottom View 5 Tripod Mounting Bracket Screw Hole 4 Auto Iris Lens Connector Used to fix the camera onto a bracket or tripod Used to connect Auto Iris Lens plug The screw sizes for this hole are as follows 1 4 20 UNC 20 THREAD L 4 5mmz0 2mm ISO standard or 0 197 ASA standard The Tripod Mounting Bracket can be unscrewed and installed on the top or bottom of the camera Make sure to use the Tripod Mounting Bracket when fixing the camera to a bracket or tripod otherwise the camera may be unstable and the internal circuitry of the camera may get damaged 1 2 Ultra Low Light High Resolution Camera 8 aly 1 2 Ultra Low Light High Resolution Camera B Overview Installation Procedures E f Video OUT Port Video signals are output through this port Connect this port to the Video IN port of a Monitor DVR 2 Auto iris lens selection switch Used to change between DC or Video depending upon the type of auto iris in use 6 8 Power
9. When it is MANUAL 0 to 127 can be selected SHUTTER 1 60 NT FLC 1 250 500 1000 2000 4000 10000 can be selected Another becomes NOT USE x When LENS is DC it is possible to select it Another becomes NOT USE ni It becomes 1 60 at NTSC It becomes 1 50 at PAL PUSH AUTO a ge can be selected AGC AGC OFF LOW MID HIGH can be selected nother becomes SENSE UP OFF X2 x4 x8 x16 x32 can be selected RETURN It returns to the MAIN MENU ECLIPSE If there is a high light installed in a limited environment such as an apartment parking garage or gas station entrance removing the high light makes it possible to view car license plates efficiently DAY NIGHT DAY In normal daylight conditions the HLC is not activated NIGHT If a high light that is larger than a certain size is present on the screen remove the high light to see license plates clearly MASKING AREA Dis b D N MODE AUTO FILTER DLY 5 SEC RETURN A ON OFF D N MODE AUTO DAY NIGHT EXT can be selected DNR This function reduces the background noise in a low luminance environment FILTER DLY When it is AUTO 4 to 10 can be selected When AGC is OFF OFF Deactivates DNR Noise is not reduced NOT USE Another becomes NOT USE ON Activates DNR so that noise is reduced RETURN It returns to the MAIN MENU RETURN It returns to the MAIN MENU 1 2 Ultra Low Light High Resolution Camera 2 SP 1 2 Ultra Low Li
10. e If the dimensions of the thread are incorrect the camera could be damaged or the lens may not get installed firmly enough C Mount Lens 10mm or less CS Mount Lens 5mm or less e f the lens is too heavy the camera becomes unbalanced which may cause problems Use a lens weighing less than 450g When adjusting the Automatic Level Control ALC of an Auto Iris Lens use Av mode if available If Pk mode is used the picture brightness may change continuously 15 1 2 Ultra Low Light High Resolution Camera B installation Procedures Using a C Mount Lens Connecting to a Monitor 1 Remove the protective cover at the front of this product and fit l l the C Mount Adapter turn it clockwise to install it Connect the video output terminal located on the rear of the camera to the Monitor DVR CCD Camera 4 B Monitor 222 Since the connection procedure may differ depending on the type of monitor or peripheral device to be connected refer to the User Manual for the device to be connected Make sure to turn off the device to be connected before making any connections e Turn the 759 Hi Z switches of interim display devices to the Hi Z position and the switches of any final device to the 7552 position Intermediate End monitor 2 ET DC REMO 4 Set the lens selec
11. e between 10 C and 50 C Be especially careful to provide ventilation when operating under high temperatures Do not install the camera under unstable lighting conditions Severe lighting change or flicker can cause the camera to work improperly Do not install or use the camera in an environment where the humidity is high It can cause the image quality to be poor Do not touch the front lens of the camera This is of the most important parts of the camera Be careful not to leave fingerprints on the lens cover 1 2 Ultra Low Light High Resolution Camera io Do not drop the camera and protect it from physical shocks Lu A It can cause malfunctions to occur Q Do not expose the camera to rain or spill beverage on it If it gets wet wipe it dry immediately Liquids can contain minerals that corrode the electronic components Never keep the camera pointed directly at strong light It can damage the CCD Do not expose the camera to radioactivity 4 If exposed to radioactivity the CCD will fail If the camera is exposed to spotlight or an object reflecting strong light smear or blooming may occur Please check the power supply satisfies the normal specification before connecting the camera 1 2 Ultra Low Light High Resolution Camera Components and Accessories Overview Front View 1 Day amp Night CCD
12. eck if the AGC menu is set to the OFF position Check if the SHUTTER menu is set to MANUAL mode 1 2 Ultra Low Light High Resolution Camera NS ITEM Sensor Number of Pixel Scanning Synchronize Horizontal frequency Vertical frequency Resolution Video out Level Burst Level S N Sensitivity Sense UP Correction AGC IRIS Control Electrical Shutter Power Supply Voltage Power Supply Current Operating Temperature Operating Humidity Weight Specification AC24V DC12V NTSC PAL 1 2 Ex view colour CCD ICX 428AKL ICX 429AKL 768 X 494 752 X 582 2 1 Interlace Internal 15 734kHz 15 625kHz 59 94Hz 50 00kHz Colour 540 TV Lines B W 570 TV Lines 1 0Vp p 758 Video 0 714Vp p Sync 0 286Vp p 0 286Vp p 50 Min AGC Correct Off 0 08Lux Colour 0 01Lux B W 0 001Lux Sens up F1 2 Max 32 times 0 45 18 Max Electrical IRIS Lens IRIS DC Lens 1 60 1 50 1 120 000sec AC24V DC12V 10 20 AC24V DC12V Max 350mA Max 490mA 10 C 50 C 90 RH max 320g 7 2 Ultra Low Light High Resolution Camera Wi Specifications AC230V ITEM NTSC PAL SEE 1 2 Ex view colour CCD ICX 428AKL ICX 429AKL Number of Pixel 768 X 494 752 X 582 Scanning 2 1 Interlace Synchronize Internal Horizontal frequency 15 734kHz 15 625kHz Vertical frequency 59 94Hz 50 00kHz Resolution Colour 540 TV Lines B W 570 TV Lines Video out Level 1 0Vp p 758 Video 0 714Vp p Sync 0
13. ght High Resolution Camera _ Camera Operation MOTION MOTION b DETECT MODE OFF DETECT AREA Tee SENSITIVITY 4 ALARM TIME 1 SEC RETURN DETECT MODE OFF or ON can be selected Turning on becomes invalid while displaying OSD However it becomes effective only at MOTION AREA DETECT AREA MOTION AREA is displayed SENSITIVITY 0 to 8 can be selected ALARM TIME 1 to 60 can be selected RETURN It returns to the MAIN MENU E MOTION AREA A thick gray shows the cursor When it is transparent the area becomes effective x Default is ALL transparent it is ALL effective When it is light gray the area becomes invalidity Cursor moved by LEFT or RIGHT When UP or DOWN is pushed it becomes effective or invalid MENU is returns to the MOTION BLC automatically becomes effective on this screen 1 2 Ultra Low Light High Resolution Camera N 24 PRIVACY PRIVACY b AREA 1 MASK OFF LEVELE 0 TOP 34 DOWN 66 PERN 20 RIGHT 66 RETURN AREA 1 to 4 can be selected MASK OFF or ON can be selected LEVEL When MASK is 0 to 15 can be selected It set the same value regardless of a set value of AREA When MASK is ON 3 to 124 NTSC or 6 to 150 PAL can be selected DOWN When MASK is ON 5 to 126 NTSC or 8 to 152 PAL can be selected LEFT When MASK is ON 0 to 187 NTSC or 0 to 185 PAL can be selected RIGHT When MASK is ON 2 to
14. low illuminance noise has been significantly reduced and the signal to noise ratio S N ratio as well as horizontal resolution have been improved resulting in a clear and sharp image display even in the dark d Controlled by OSD Menu jun The camera can be controlled by selecting text displayed on the monitor screen bush d Additional Functions i a m SENS UP MOTION DETECTION MIRROR SHARPNESS and SYNC INT AUTO functions are also available NN RS 485 Communication Control Support Remote OSD menu control via an RS 485 interface is supported Warning The camera requires periodic inspection Contact an authorised technician to carry out the inspection Stop using your camera when you find it malfunctioning If the camera emits smoke or is unusually hot for a long period a fire may be caused Do not Install the camera on a surface that can not support it If the camera is installed on an inappropriate surface it may fall and cause injury Do not hold plug with wet hands It could cause an electric shock Do not dis assemble the camera It may result in an electric shock or other hazards Do not use the camera close to a gas or oil leak It may result in a fire or other hazards 1 2 Ultra Low Light High Resolution Camera B Precautions Do not install the camera in extreme temperature conditions 22 2L Ag Only use the camera under conditions where temperatures ar
15. ndard voltage for camera operation DC 12V 1096 AC 24V 31 1096 There may be some deviation in voltage drop depending on the type of wire and the manufacturer 1 2 Ultra Low Light High Resolution Camera N Control via the RS 485 Interface The camera can be controlled by using an external controller equipped with RS 485 communications To control using a DVR or keyboard controller Connect the RS 485 cable TRX TRX to the connection port of the 485 control board in the DVR or controller 485 Control Board Connection Port RS 485 Control Port CONNECTION TERMINAL TRX 4854 CONNECTION TERMINAL TRX 485 RS 485 communication default initial values Item Camera ID BAUD RATE UART MODE PET PKT Initial value 1 9600 8 NONE 1 ENABLE To control the camera use Pelco D protocol Go Preset 95 Enters into OSD menu or Set key function 19 1 2 Ultra Low Light High Resolution Camera _ Camera Operation MENU EXPOSURE WHITE BAL DAY NIGHT MOTION PRIVACY OPTION DISPLAY SYNC INITIAL EXIT MAIN MENU LENS BRIGHTNESS BACKLIGHT SHUTTER AGC SENSE UP ECLIPSE DNR WB MODE RED CONT BLUE CONT PUSH AUTO DIN MODE FILTER DLY DETECT MODE DETECT AREA SENSITIVITY ALARM TIME AREA MASK LEVEL DOWN LEFT RIGHT TITLE NEGA POSI SHARPNESS MIRROR ZOOM PAN TILT PHASE TITLE MOTION DET CAMERAID
16. ne n3 sgp SALA 18 Specification AC24V DC1 2V 31 Control via RS 485 Wie aCe erc erede e tdt 19 Specifications AC230V MEHREREN 32 1 2 Ultra Low Light High Resolution Camera LE 1 2 Ultra Low Light High Resolution Camera Features 7 Fine Picture in Ultra Low Mumination 1 2 inch CCD allows bright and high quality images to be captured in ultra low light condition Colour 0 08Lux F1 2 BW 0 01Lux F1 2 Sens up 0 001Lux F1 2 Ultra High Resolution Fae By adopting a 410 000 pixel Sony CCD the camera produces clear picture quality with a horizontal resolution of 540 TV lines for colour and 570 TV lines for B W Filter Changeable Day amp Night P This camera has a function that auto matically selects the mode that is appropriate for daytime or night time conditions The COLOUR mode operates in daytime conditions to provide optimum colours and BW mode operates in nighttime conditions to enhance the definition of the image Electronic IRIS J N a The electronic IRIS function enables continuous automatic control of the shutter between 1 60 1 50 1 120 000 seconds b 2 Privacy Function 1 2 Ultra Low Light High Resolution Camera a e QU The PRIVACY function conceals the areas you do not wish to appear on the screen NM lt 2 DNR Digital Noise Reduction The amount of
17. nes the camera s identification number When MENU is pushed by BS one character can be deleted between 0 and 255 When MENU is pushed by POS POSITION is displayed BAUD RATE You can select 2400 9600 bps Only when you set the character by one character or more RETURN It returns to the MAIN MENU When MENU is pushed by END return to the OPTION B is brank js space 1 2 Ultra Low Light High Resolution Camera I UP 1 2 Ultra Low Light High Resolution Camera _ Camera Operation Troubleshooting SYNC If there are problems with the camera operation check the tables below If the problem persists please contact the agent who supplied the product Two sychronisation modes are available INTERNAL and AUTO In AUTO mode it synchronises the video signal between cameras without a synchronous generator The line lock synchronisation is only used in areas of Problems Troubleshooting 60Hz NTSC Models 50Hz PAL Models INT Internal synchronisation Nothing appears on the Check the power connection screen AUTO External line lock synchronisation Check the video signal line connection INITIAL Returns to the level which was set by the manufacturer for shipment The video image is not Make sure that the lens is clean clear Clean the lens with a clean lint free cloth or brush EXIT Adjust the contrast control on the monitor Make sure that the screen is not exposed directl
18. tion switch located on the rear of the camera to either DC or VIDEO depending on the type of auto iris lens being used 1 2 Ultra Low Light High Resolution Camera LLL 0 1 2 Ultra Low Light High Resolution Camera B installation Procedures Connecting to Power Since power specifications differ depending on the model make sure to check your model name and specifications before connecting power You can connect power as shown in the following figure For AC DC power Check the standard power requirement before connecting to power Dual Power Type AC 24V DC 12V AC 24V Class2 AC90 230V 50HZ 60Hz 4 5W DC Power Type DC 12V 500mA AC90 230V 50Hz 60Hz 4 5W REMOTE DIN E When the resistance value of copper wire is at 20 C 68 F 24 0 22mm 22 0 33mm 420 0 52mnv 18 0 83mm 0 078 0 050 0 030 0 018 0 028 0 018 0 011 0 006 As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera Sta
19. y to a bright light Re position the camera if necessary Saves all the setting menus and then exits The screen is dark Adjust the contrast control of the monitor If there is an intermediate device set the75ohm Hi z correctly and also check the connections If necessary adjust the brightness level There is a problem with the camera operation The camera surface is too hot and black stripes appear on the screen Check if an appropriate power source to the camera complies with the manufacturer s standard requirement or if the voltage is fluctuating Check for ground loops 1 2 Ultra Low Light High Resolution Camera 28 EUM 1 2 Ultra Low Light High Resolution Camera WM Troubleshooting Problems The MOTION DETECTION function is not working Colours are not quite right The screen is flickering L L mode isn t able to be selected L L mode is not available COLOUR mode is not working SENSE UP function is not working Troubleshooting Check if MOTION DETECTION mode is turned on Check the setting of the MD AREA Check the WHITE setting Please refer to page 23 Check if the camera is facing directly into sunlight or fluorescent light Have you connected your camera to DC power source Connect it to AC power source Check the frequency of power supply 60Hz for NTSC 50Hz for PAL Check if the AGC menu is set to the OFF position Ch
Download Pdf Manuals
Related Search