Home

NetGuardian 1664

1. 1 Receive In Rk Regular Ethernet port pinout The four Ethernet ports of the switch are regular straight through Ethernet ports The pmout for the regular Ethernet ports is shown in the figure above 24 6 8 2 Integrated T1 E1 Port If you ordered your NetGuardian with a T1 or E1 port you can connect to your NetGuardian via Tl or El and pass LAN traffic over T1 E1 or vice versa through the NetGuardian s internal switch T1 E1 WAN wae Link Act 100M GLD ECU TELCO A NetGuardian with integrated E1 TI WAN port Note Both the T1 E1 port and the 4th port on the integrated switch are tied internally to Net2 If using the integrated T1 E1 connection you can convert traffic to LAN only on switch ports 1 3 from left to right 6 8 3 GSM GPRS or CDMA Wireless Modem Top Board Optional 1 4 Amp Fuse Wireless type Wireless Modem for Modem GSM GPRS or CDMA Antenna Jack eri Fuse ip Poa Wee eee LETTU GLDECU TELCO NetGuardian 1664 wireless modem option You can order your NetGuardian 1664 with an optional GSM GPRS or CDMA wireless modem which provides wireless network connection The wireless modem is powered by the same 48 VDC power as the NetGuardian which provides more secure more robust operation than modems that run off commercial power To power and activate the wireless modem top board insert the provided 1 4 amp fuse in the wireless modems fuse socket If you ever want to turn off p
2. 19 6 6 4 Analog Dipswitches Dipswitch up on for current Current 4to 20 ma Current Source Transducer ON sirr ir iiiiiiii DOWN e OFF IMIDE Voltage 2 Voltage Source Transducer The analogs are controlled by the dipswitches accessible via the top sliding panel For milliamp sensor operation current loop turn the dipswitch on by placing it in the up ON position For voltage operation place the dipswitch in the down OFF position e Hatch Panel Access for Analog Dipswitches Analog Block 8 Accessed Through this Window WARNING Do not put the dipswitches in the upward ON position current loop mode unless you are sure of the analog setting Having the dipswitch on puts a 250 ohm resistor across the input lines Any voltage beyond 5V or 20 mA will damage components 20 6 6 5 Integrated Temperature and Battery Sensor Optional 3 4 AMP GMT The external temperature sensor The optional integrated temperature and battery sensor monitors the ambient temperature and the NetGuardian s power inputs This option is available only if it was ordered with your NetGuardian The integrated temperature sensor measures a range of 32 F to 140 F 0 C to 60 C within an accuracy of 1 Analog Input Internal Temperature analog input 4 Power Feed A analog input 5 Power Feed B analog input 6 External Temperature analog input 8 Integrated
3. 16 NetGuardian DX48 Expansion 2 Alarms 1 48 6257 6305 7257 7305 1 99 1 17 NetGuardian DX48 Expansion 2 Relays 1 8 6321 6328 7321 7328 Display descriptions and SNMP Trap numbers for the NetGuardian DX48 Expansion Port Address Display Description Set Clear 9 1 14 NetGuardian 832A Expansion 1 as DX Alarms 1 32 6129 6161 7129 7161 99 1 15 O NetGuardian 832A Expansion 1 as DX Relays 1 8 o 6193 6200 7193 7200 9 1 16 NetGuardian 832A Expansion 2 as DX Alarms 1 32 o 6257 6289 7257 7289 9 1 17 Oo NetGuardian 832A Expansion 2 as DX Relays 1 8 6321 6328 7321 7328 Display descriptions and SNMP Trap numbers for the NetGuardian DX G5 832A model Port Address Display Description Set Clear 9 1 14 NetGuardian 864A Expansion 1 as DX Alarms 1 64 o 6129 6192 7129 7192 99 1 15 NetGuardian 864A Expansion 1 as DX Relays 1 8 o 6193 6200 7193 7200 ee ee E E NetGuardian 864A Expansion 2 as DX Alarms 1 64 6257 6320 7257 732 NetGuardian 864A Expansion 2 as DX Relays 1 8 6321 6328 7321 7328 Display descriptions and SNMP Trap numbers for the NetGuardian DX G5 864A model S Channel 9 6385 6388 7385 Analog Channel 9 10 e 1388 Clear D D e ep Q OO O Go N 1389 1392 1393 1396 7400 7404 7408 1412 t D D ep Go le GO O Go Analog Channel 11 12 5 5
4. 3 RX Receive Grange kae HC Not Connected 1 TX Transmit Green Data Port Pinout 6 8 Hardware Options The NetGuardian 1664 has a number of additional hardware options that you may have specified when you ordered your RTU For more information about NetGuardian hardware options that you may have ordered with your NetGuardian see the subsections of this chapter Note You must order your NetGuardian with the options contained in this chapter You cannot add them to your NetGuardian after it has been built and shipped 23 6 8 1 Integrated 10 100BaseT Ethernet Switch Optional M4 AMP Fuse Switch Status Switch for Switch LEDs Parts Discretes 1 24 ai TELCO 1 NetGuardian integrated Ethernet Switch hoo You can order your NetGuardian 1664 with an optional integrated Ethernet switch which provides four regular Ethernet ports The integrated Ethernet switch is powered by the same 48 VDC power as the NetGuardian which provides more secure more robust operation than switches that run off commercial power The integrated switch also frees valuable rack space by eliminating an unnecessary extra unit To power and activate the integrated Ethernet switch insert the provided 1 4 amp fuse in the switches fuse socket If you ever want to turn off power to the integrated switch just remove the fuse RJ45 Ethernet Connection 8 7 6 Trasmit Out TO 5 il 3 Transmit Out TO 2 Receive In RI
5. EXT TEMPERATURE CHANNEL 3 CHANNEL 4 CHANNEL 9 CHANNEL 6 CHANNEL 5 8 9 Ma CHANNEL CHANNEL CHANNEL 10 CHANNEL bk eo Oo Eo a ug elK it Tjune Modem Event log s Wiitch Rieset Port ESC H a C cum Timer Sjystem afR p Dibg ESC 7 H Reading Units MJU HnU Hn0 Mj0 Err F HK 33 o08 0 000 YDC z 0 0000 VDC 16 9094 VDC j 44 9872 VDC K 60 0000 VDC z 0 0000 VDC 5 z 4 9857 VOL 0 0000 VDC 4 9857 VOL This display allows you to monitor your eight analog inputs 55 13 3 1 4 Monitoring System Alarms View the status of the NetGuardian s system alarms from the M onitor menu gt S ystem option Under Status the word Alarm will appear if an alarm has been activated and Clear will appear if an alarm condition is not present See Appendix System Alarm Descriptions for more information If groups are used the user defined status will be displayed Alarms Relays a N alogs Event log a C cum Timer BJAC Pling targets plO rts S ystem ESC 75 ID Description Status 1 Timed Tick Clear 16 Exp Module Callout Clear 19 Network Time Server Clear 20 Accumulation Event Clear 33 Unit Reset Clear 36 Lost Provisioning Clear 3 DCP Poller Inactive Clear 36 LAN not Active Clear 41 Modem not Responding Clear 42 No Dialtone Clear 43 SNMP Trap not Sent Clear 44 Pager Que Overflow Clear 49 Notification Failed Clear 46 Craft Rev Full Clear 47 Modem Rev
6. Menu Shortcut Keys The letters before or enclosed in parentheses are menu shortcut keys Press the shortcut key to access that option Pressing the ESC key will always bring you back to the previous level Entries are not case sensitive 44 13 1 Establishing an SSH Session If your NetGuardian was purchased with the hardware acceleration option you may connect to your NetGuardian s TTY interface via SSH session If you are unsure as to whether or not your NetGuardian is equipped with hardware acceleration reference your NetGuardian s model number D PK NET1664 and contact support dpstele com DPS Telecom recommends using PuTTY to access the TTY interface via SSH session To establish an SSH session with your NetGuardian using PuTTY e Open Putty e Click Session In the Host Name or IP address field input the IP of your NetGuardian To enable backspacing within the TTY interface click Keyboard on the left pane underneath Terminal In that tab select Control H under The Backspace Key option e Click Open e When prompted enter your username and password as with a standard TTY session Category Session Basic options for your PuTTY session Logging Specify the destination you want to connect to J T Termina Host Name for IP address Port Keyboard Bell 126 10 230 121 22 Features Connection type Window O Raw OTelnet Rlogin SSH Serial Appearance 3 E Load save or delete a stored
7. T NO O ioe CO N O N O O Q 5 5 D a AK O K O Ql O K O 5 5 E O K O CO O K a NO 5 5 ER O K a oo O K a O Analog Channel 13 14 7416 Analog Channel 15 16 Channel 1 6417 6420 22 7420 17417 1424 Channel 3 6425 6428 7425 7428 NetGuardian G5 Expansion 1 as DX Analog Channels Channel 4 6429 6432 7499 7432 Channel 5 6433 6436 7433 7436 NetGuardian G5 Expansion 1 as DX Analog Channels Channel 6 16437 64401 7437 7440 NetGuardian G5 Expansion 1 as DX Analog Channels hanne GaGa E NetGuardian G5 Expansion 1 as DX Analog Channels Channel 2 6421 6424 7421 O O O O O O O gt gt gt 3 gt gt ey D D D D gt gt D D D ok ol ao Go K O K K 63 ra so S 7448 Channel 1 6449 6452 7449 7452 NetGuardian G5 Expansion 2 as DX Analog Channels Channel 2 16453 64561 7453 7456 Channel 3 6457 6460 7457 7460 NetGuardian G5 Expansion 2 as DX Analog Channels Channel 4 6461 6464 7461 7464 Channel 5 6465 6468 7465 7468 NetGuardian G5 Expansion 2 as DX Analog Channels Channel 6 6469 6472 7469 7472 Channel 7 6473 6476 7473 l 7476 NetGuardian G5 Expansion 2 as DX Analog Channels Channel 8 6477 6480 7477 7480 Display descriptions and SNMP Trap numbers for the NetGuardian DX G5 832A 864A Analog Channels 14 1 1 System Alarms Display Map et Ee ee a Ne
8. TTY Command Mode 13 3 Monitoring 13 3 1 13 3 2 13 3 3 13 3 4 13 3 5 13 3 6 Monitoring the NetGuardian 13 3 1 1 Monitoring Base Alarms 13 3 1 2 Monitoring Ping Targets 13 3 1 3 Monitoring Analogs 13 3 1 4 Monitoring System Alarms 13 3 1 5 Monitoring Data Port Activity 13 3 1 6 Monitoring the Accumulation Timer Viewing Live Target Pings Proxy Menu Event Logging Backing Up NetGuardian Configuration Data va FTP 13 3 5 1 Reloading NetGuardian Configuration Data Debug Input and Filter Options 14 Reference Section 34 35 35 36 36 36 37 38 39 40 40 40 40 42 43 44 44 44 45 46 46 47 48 49 50 53 53 53 53 54 55 55 55 56 57 57 58 59 60 61 14 1 Display Mapping 14 1 1 System Alarms Display Map 14 2 SNMP Manager Functions 14 3 SNMP Granular Trap Packets 14 4 Trap SNMP Logic 14 5 ASCII Conversion 14 6 RADIUS Disctionary File Available on Resource Disk 15 Frequently Asked Questions 15 1 General FAQs 15 2 SNMP FAQs 15 3 Pager FAQs 16 Technical Support 17 End User License Agreement 61 64 6 68 70 70 71 72 72 74 19 75 78 1 NetGuardian 1664 Overview 4 NetGuardian 1664 The NetGuardian has all the tools you need to manage your remote site The NetGuardian 1664 The Intelligent RTU for Complete Site Management The NetGuardian 1664 is a RoHS 5 6 compliant LAN based SNMP DCPx remote telemetry unit The NetGuardian has all the tools you need t
9. activated and Clear will appear if an alarm condition is not present B ase A larms Rjelays afN alogs AC Pjing targets ID Description ESC to exit p O rts E xpansions ESC lt E vent log Any key to continue a C cum Timer S ystem ESC P Status 9 Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear IP Address 299 290 290 29 The Ping info submenu allows you to change ping targets 13 3 1 3 Monitoring Analogs View the current reading and the alarm status of your analog devices from the M onitor menu gt a N logs option 54 The value shown is a snapshot of the channels measurement not a real time reading Refresh the readings by re selecting the analogs option Alarm status indicates that a preset threshold has been crossed and is designated by an X The sixteen analog measuring inputs are set to measure voltage as the factory default If your sensors output is current change the appropriate analog dip switch to the current measuring position The scaling worksheet in the provisioning section converts all readings shown here into native units such as degrees Celsius or percent relative humidity Password JE JE FE HE EE HE EE NetGuard an 1664 yvo 1F 6006 D eb Clonfig Pjroxy Telnet Eldit Monitor Pling S tats Ajlarms re Ljays afNjalogs BJAC Pling targets plO rts E xpansions ESC B Bjase Chn Description
10. inne you like to Reset the Event Log lt y N3 Monitor the last 100 events recorded by the NetGuardian from the M jonitor menu gt E vent log option Alarm Group State of the event A alarm C clear PRef Point reference See Appendix A for display descriptions S User defined description of the event as entered in the alarm point and Description a relay description fields Event Log field descriptions 13 3 5 Backing Up NetGuardian Configuration Data via FTP From the Start menu on your PC select RUN Type ftp followed by the IP address of the NetGuardian you are backing up e g ftp 126 10 120 199 After the connection is made press Enter Enter the password of the NetGuardian default password is dpstelecom then press Enter Type binary and press Enter necessary for NetGuardian file transfer Type Icd and press Enter this allows you to change the directory of your local machine a ey Pe ge A e S Type get followed by the name you wish to define for the NetGuardian backup file Add the extension bin to the file name e g get ngdbkup bin and press Enter 8 After reloading type bye and press Enter to exit Note The backup file name can have a maximum of eight characters before the file extension 59 13 3 5 1 Reloading NetGuardian Configuration Data S Oy E a ee A From the Start menu on your PC select RUN Type ftp followed by the IP address of the NetGuardian you are backing up e g
11. soon as possible T7 78 17 End User License Agreement All Software and firmware used in for or in connection with the Product parts subsystems or derivatives thereof in whatever form including without limitation source code object code and microcode including any computer programs and any documentation relating to or describing such Software is furnished to the End User only under a non exclusive perpetual license solely for End User s use with the Product The Software may not be copied or modified in whole or in part for any purpose whatsoever The Software may not be reverse engineered compiled or disassembled No title to or ownership of the Software or any of its parts is transferred to the End User Title to all patents copyrights trade secrets and any other applicable rights shall remain with the DPS Telecom DPS Telecom s warranty and limitation on its liability for the Software is as described in the warranty information provided to End User in the Product Manual End User shall indemnify DPS Telecom and hold it harmless for and against any and all claims damages losses costs expenses obligations liabilities fees and costs and all amounts paid in settlement of any claim action or suit which may be asserted against DPS Telecom which arise out of or are related to the non fulfillment of any covenant or obligation of End User in connection with this Agreement This Agreement shall be construed and enforced in
12. 1 To use both network interfaces be sure Netl and Net2 are on separate Subnet Masks To use only one of the network interfaces set either Netl or Net2 to IP address being used and set the unused network IP subnet and gateway to 255 255 255 0 If your NetGuardian has the 4 port hub build option use Net2 which is connected to the Hub Both ports are standard RJ45 ports that take standard RJ45 Ethernet cables If the IP connection is OK the LNK LED will ight SOLID GREEN when the cable is connected The NetGuardian unit with the integrated switch comes with two physical 10 100 Ethernet ports The standard unit without the switch comes equipped with two physical Ethernet ports The switch is internally tied to NET2 and any one of its four ports can be used for uplink Build Option NetGuardian 1664 with GigE Fiber Top Board If your NetGuardian was ordered with the GigE Fiber top board 1000Base SFP interface must be used The SFP ports are internally connected to the 4 port switch and NET 2 SFP Fiber Ports 1000 Base X 10 100 1000 BaseT Switch Back panel of NetGuardian G5 with fiber 14 15 6 5 Telco Connection 10 100 Telco jack The rear panel telco jack connects the NetGuardian internal modem to a standard phone line for dial up access and pager alarm notification RJ11 Phone Line Connection A 3 Ring 2 Tip 1 Telco jack pinout The pmout for the Telco jack is shown above 6 6 Alarm Connections Alarm and an
13. Su B SC S VT Vertical Tabulation RS Record Separator FF FomFeed Us Unit Separator Ss Shift In Break Received ASCII symbols VT FF 71 14 6 RADIUS Disctionary File Available on Resource Disk text dictionary dps r DPS Telecom Inc For assistance or support please contact support dpstele com v1 0 Released 1 23 09 CBH DPS VENDOR DPS 2682 Standard attribute for NetGuardian RTU All values are integer with True 0 False If attribure does not exist in Access Accept packet default value will be 0 BEGIN VENDOR DPS ATTRIBUTE dps admin integer ATTRIBUTE dps edit 2 integer ATTRIBUTE dps monitor 3 integer ATTRIBUTE dps SD monitor 4 integer To allow monitor of data port buffer activity ATTRIBUTE dps reach through 5 integer To allow proxy to serial ports via TTY interface ATTRIBUTE dps telnet 6 integer To allow telnet in and out of NetGuardian ATTRIBUTE dps control 7 integer To allow manipulation of dry contact relay outputs ATTRIBUTE dps modem 8 integer To allow dial in and out of NetGuardian ATTRIBUTE dps ppp 9 integer To allow this user PPP inbound access to the NetGuardian END VENDOR DPS 72 15 Frequently Asked Questions Here are answers to some common questions from NetGuardian users The latest FAQs can be found on the NetGuardian support web page http www dpstelecom com If you have a question about the NetGu
14. VDC Optional Wide Range 24 48 VDC 18 to 58 VDC Optional 24VDC 18 to 36 VDC Optional 12VDC 411 to 18 VDC 300 mA at 48 VDC 600 mA at 24 VDC 3 4 amp recommended ND A Am 12 VDC 24 VDC Up to 250 mA at either 12 or 24 VDC May increase by 150 mA at 48 VDC 3 4 amp recommended 33 6 K internal LCD display 16 bicolor LEDs 5 unicolor LEDs 10 with Switch Option Audible Notification Alarm speaker Operating Temperature 32 to 140 F 0 to 60 C Industrial Temperature Option 22 to 158 F 30 to 70 C Operating Humidity 0 95 noncondensing MTBF 60 years Windows Compatibility Windows 95 98 NT ME XP 2000 Vista 7 32 64 bit RoHS 5 Approved Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 10 6 Hardware Installation 6 1 Tools Needed To install the NetGuardian you l
15. WAGO connector with a screwdriver and inserting the wire into the slot then releasing the screwdriver Insert a 48 VDC line to the plug s slots 1 and 3 using the same method as before Inserting a 48 VDC Line into Slot 1 of WAGO Connector 5 Push the power connector plug firmly back into the power connector If the power feed is connected correctly IB the LED by the connector will light GREEN If the polarity of the power feed is reversed the LED will not illuminate 6 Reinsert the fuses to power the NetGuardian The front panel LEDs will flash RED and GREEN 6 4 LAN Connection lt gt 56 RJ45 Ethernet Connection Discretes 1 24 GLD ECU TELCO Two 10 100 Ethernet ports With Switch 6 Receive In RI 4 3 Receive In Rit 2 Transmit Out TO 1 Transmit Out TO Ethernet port pinout i aamz Inam GLD ECU TELCO 10 100 Two 10 100 Ethernet ports Without Switch For enhanced security the NetGuardian 1664 has two 10 100 Ethernet ports Each port has its own separate IP address and subnet so you can safely connect one port to your private company LAN and the other to the public Internet There is no routing between Net 1 and Net 2 this ensures that both connections are independent of each other By default outbound data traffic from the NetGuardian 1664 will be sent over Net 2 Only outbound data that is specifically directed to Net 1 usually the Company s LAN will be sent to Net
16. accordance with the laws of the State of California without regard to choice of law principles and excluding the provisions of the UN Convention on Contracts for the International Sale of Goods Any dispute arising out of the Agreement shall be commenced and maintained only in Fresno County California In the event suit is brought or an attorney is retained by any party to this Agreement to seek interpretation or construction of any term or provision of this Agreement to enforce the terms of this Agreement to collect any money due or to obtain any money damages or equitable relief for breach the prevailing party shall be entitled to recover in addition to any other available remedy reimbursement for reasonable attorneys fees court costs costs of investigation and other related expenses Dependable Powerful Solutions that allow users to monitor larger more complicated networks with a smaller less trained staff Yere DPS Telecom Your Partnersin Network Alarm Management www dpstelecom com 4955 E Yale Fresno CA 93727 559 454 1600 e 800 622 3314 e 559 454 1688 fax
17. asked if you would like to save changes type Y yes 11 Reboot to save the new configuration to the NetGuardian 12 Now you can connect to the NetGuardian via LAN and use either NGEdit software over LAN or the Web Browser to complete the configuration 13 2 1 1 T1 E1 WAN Settings E1 T1 WAN Settings If using the NetGuardian in an E1 T1 WAN network with DPS Telecom s WAN MUX and VLAN Router accessories you must also assign the NetGuardian a WAN ID The WAN ID corresponds to the ID number of the WAN MUX port 1 16 to which you connect the NetGuardian To assign a WAN ID 1 From the E thernet menu select the G lobal option 2 Select the t 1 e1 option 3 Assign a WAN ID 1 16 corresponding to the WAN MUX port to which you will connect the NetGuardian Note If your NetGuardian has a T1 E1 port but you are not using the WAN MUX and VLAN Router accessories do not assign a WAN ID 46 13 2 1 2 New Backup Mode BSE NetGuardiani664 v5 4k 0080 Config Piroxy Telnet Debug et it Edit Monitor Ping Stats Iune Modem Reset Port CESC 7 E Ethernet ntUdram POPP D ate time ECASDIUS R eboot ESC 7 E Global WET lt 1i WET 2 gt ESG 2 Het 2 Interface Unit Address z 126 816 268 114 126 618 241 146 gt Subnet Mask gt 255 255 192 000 255 255 192 AAA Default Gateway 255 255 255 255 126 616 226 192 gt Link Status Detected not in use Backup Mode Enabled Autoswitch z Disabled MAG Address 8H 1
18. ftp 126 10 120 199 After the connection is made press Enter Enter the password of the NetGuardian default password is dpstelecom then press ENTER Type binary and press Enter necessary for NetGuardian file transfer Type lcd and press Enter this allows you to change the directory of your local machine Type put followed by the name you defined for the NetGuardian backup file and press Enter e g put ngdbkup bin Type literal REBT to reboot the NetGuardian After reloading type bye and press Enter to exit 13 3 6 Debug Input and Filter Options Debug Input Options ESC Exit Debug Show BAC status points Show task status Show DUART information Show network routing table Clear debug enable bitmap Turn all debug filters OFF Display Options Debug Filter Options 1 Alarm toggle switch Shows posting of alarm data 2 3 _ Analog toggle switch Shows TTY interface debug Config toggle switch Shows TTY interface debug xe SJ dy IN 10 a gt Ila om lt Control relay toggle switch Shows relay operation Ol DCP responder toggle switch Shows DCP protocol 6 Device toggle switch Shows telnet and proxy information and NGEdit1664 serial ommunication N Expansion poller toggle switch Shows NGDdx polling 8 9 ECU Interrogator toggle switch Shows BAC processing FTP Command toggle switch Shows command string parsing FTP Data toggle switch Shows
19. gt DPS Telecom Your Partners In Network Alarm Monitoring NetGuardian 1664 OoOo a m an Visit our website at www dpstelecom com for the latest PDF manual and FAQs February 25 2013 D UM N1664 Firmware Version 5 4K This document contains proprietary information which is protected by copyright All rights are reserved No part of this document may be photocopied without prior written consent of DPS Telecom All software and manuals are copyrighted by DPS Telecom Said software and manuals may not be reproduced copied transmitted or used to make a derivative work by either mechanical electronic or any other means in whole or in part without prior written consent from DPS Telecom except as required by United States copyright laws 2013 DPS Telecom Notice The material in this manual is for information purposes and is subject to change without notice DPS Telecom shall not be liable for errors contained herein or consequential damages in connection with the furnishing performance or use of this manual Contents Visit our website at www dpstelecom com for the latest PDF manual and FAQs 1 NetGuardian 1664 Overview 2 About This Manual 3 Shipping List 3 1 Port Allocation Optional Accessories Specifications Hardware Installation 6 1 Tools Needed 6 2 Mounting 6 3 Power Connection 6 4 LAN Connection 6 5 Telco Connection 6 6 Alarm Connections 6 6 1 Alarm Connector Pinout Table 6 6 2 Discretes 1 48 Con
20. the NetGuardian Connect a PC running VT100 terminal emulation software to the craft port or connect via LAN using a Telnet client with VT100 emulation to port 2002 to reach the monitor menu selection This section allows you to do full system monitoring of the NetGuardian including all alarms ping information relays analogs and system status Config P roxy Tjelnet Dlebug elklit Ejdit M onitor Pj ing S tats Tjune Modem Rjeset Port ESC H Allarms Rielays alNjalogs Ejvent log a C cum Timer BJAC Pjing targets plO rts S ystem ESC The monitor menu allows status checking on all elements 13 3 1 1 Monitoring Base Alarms View the status of the device connected to the discrete alarms from the M onitor menu gt A larms option Under Status the word Alarm will appear if an alarm has been activated and Clear will appear if an alarm condition is not present If groups are used the user defined status will be displayed A larms Rjelays afN alogs Ejvent log afC cum Timer B AC P ing targets plO rts S ystem ESC A Bjase E xpansions ESC B ID Description 1 J A 9 6 a 8 9 1 ESC to exit Any key to continue This example shows page two of the discrete alarms 13 3 1 2 Monitoring Ping Targets View the status of all your ping targets from the M onitor menu gt P ing targets option This screen displays the ping target ID description and IP address Under Status the word Alarm will appear if an alarm has been
21. where you enter your pager number First enter the pager number then enter some commas directly after the number Each comma represents a two second delay So for example if you wanted an eight second delay you would enter 555 1212 in the Pager Number field gt What do I need to do to set up e mail notifications You need to assign the NetGuardian an e mail address and list the addresses of e mail recipients Let s explain some termmology An e mail address consists of two parts the user name everything before the sign and the domain everything after the sign To assign the NetGuardian an e mail address choose System from the Edit menu Enter the NetGuardian s user name in the Name field it can t include any spaces and the domain in the Location field For example if the system configuration reads Name netguardian Location proactive com Then e mail notifications from the NetGuardian will be sent from the address netguardian proactive com The next step is to list the e mail recipients Choose Pagers from the Edit menu For each e mail recipient enter his or her e mail domain in the Phone Domain field and his or her user name in the PIN Rcpt Port field You must also enter the IP address of an SMTP server in the IPA field and configure the alarm point to use the pager you setup as email gt 16 Technical Support DPS Telecom products are backed by our courteous friendly Technical Support represe
22. will not work correctly with the NetGuardian I can t change the craft port baud rate If you select a higher baud rate you must set your terminal emulator program to the new baud rate and then type DPSCFG and press Enter If your terminal emulator is set to a slower baud rate than the craft port normal keys can appear as a break key and the craft port interprets a break key as an override that resets the baud rate to the standard 9600 baud How do I use the NetGuardian to access TTY interfaces on remote site equipment If your remote site device supports RS 232 you can connect it to one of the eight data ports located on the NetGuardian back panel To make the data port accessible via LAN configure the port for TCP IP operation You now have a LAN based proxy port connection that lets you access your device s TTY interface through a Telnet session Q I just changed the port settings for one of my data ports but the changes did not seem to take effect even after I wrote the NVRAM In order for data port and craft port changes including changes to the baud rate and word format to take 73 gt gt effect the NetGuardian must be rebooted Whenever you make changes remember to write them to the NetGuardian s NVRAM so they will be saved when the unit is rebooted The LAN link LED is green on my NetGuardian but I can t poll it from my T Mon Some routers will not forward packets to an IP address until th
23. with the Real Time Clock hardware option Once it s set the Real Time Clock will keep the correct date and time regardless of reboots Network Time Protocol Synchronization If your NetGuardian has Firmware Version 2 9F or later you can configure the unit to automatically synchronize to a Network Time Protocol NTP server e To get the latest NetGuardian firmware sign in to MyDPS at www dpstelecom com mydps e For instructions on configuring your NetGuardian to use NTP synchronization see your NGEditG5 or NetGuardian Web Browser Interface user manual T Mon RTU Time Sync Signal You can configure your T Mon NOC to send an RTU Time Sync signal at a regular interval which you can set to any time period between 10 and 10 080 minutes The Time Sync will automatically synchronize the NetGuardian s clock to the T Mon s clock And if you set your T Mon to NTP gt 14 synchronization you ll make sure you have consistent accurate time stamps throughout your monitoring network How do I back up my NetGuardian configuration There are two ways to back up NetGuardian configuration files Use NGEdit1664 NGEdit1664 can read the configuration of a NetGuardian unit connected to your PC via LAN modem or COM port You can then use NGEdit1664 to save a NetGuardian configuration file on your PC s hard disk or on a floppy disk With NGEdit 1664 you can also make changes to the configuration file and write the changed configuration to the NetGuardia
24. 1 CTS Clear to Send 1 TX Transmit Yost 4 Wire 202 Connector 8 TX Transmit 7 N C Not Connected 6 RX Receive 5 GND Ground 4 GND Ground 3 RX Receive 2 N C Not Connected 1 TX Transmit Data port pinouts op i At a NNA Pm Pin H Location of Pin 1 on RJ 45 Connector NetGuardian data ports can be configured for Yost RS 232 RS 485 and 4 wire 202 RJ45 connects These data 22 ports are available as optional builds on NetGuardian hardware units Call DPS Sales for more information 1 800 693 0351 The pinouts for Data Ports 1 8 are shown above DB9 RS 232 Pin Signal Description RX 1 Not connected liz ii 2 TX Transmit data 54321 3 RX Recieve Data 4 Not connected 5 GND Ground 9876 6 Not connected CTS Clear to send pre CTS 8 RTS Request to send 9 Not connected DB9 RS 232 Pinouts Craft Port Only 6 7 1 Connecting NetGuardian Accessories Some NetGuardian accessories must be connected to particular data ports However if you don t use these accessories the data ports are available for other uses If you are using a NetGuardian Expansion connect it to Port 7 6 7 2 GLD ECU Expansion Port RS 485 If you are using a General LCD Display GLD unit connect it to the GLD ECU port ge mz TELCO GLD ECU Port RS 485 RJ45 Connector IEE TX Transmit Value fy T WC Not Connected A RX Recelve uman 5 WC Not Connected 4 AC Net Connected 7
25. 12 12 ar ANA 12 f 12 ANA13 13 38 ANA134 13 ANA 14 da 39 ANA 14 14 ANA15 15 40 ANAT5 15 ANATIB 16 41 ANA18 16 FA NO 17 42 FACO 17 Unused 18 43 Unused 18 ANA 1 49 44 ANA 1 19 See gn ANA 2 20 45 Saag Eas GRY YEL ANA 2 20 DE D VIO BLU ANA 3 21 46 BLUVIO ANA 3 21 ee m VIOVORG ANA 4 29 47 re SE ORGMO ANA 4 22 Y OMGRN ANA 5 94 48 Oee GRNMVIO ANA 5 23 a va GRE VIOBRN ANA 6 24 49 e We BRN VIO ANA NY aes ey ee VIO GRY RTN 25 e E Ro GND 25 66 Block connections for Discretes 49 64 and Analogs 1 6 9 16 RTN is the alarm return pin Alarms on standard units are dry closure or ground closure Most units will have RTN internally tied to GND However special hardware assemblies may have RTN isolated from GND For details regarding your unit s hardware please reference the product description appendix 30 6 10 Optional Hinged Wire Wrap Back Panel NetGuardian 1664 bazas Zee 12VDC waup gur 14 ame GUT 10BaseT Hub aoe ae a d e 7 t ot 2 i 4 G a piscreres 10 DISCRETES ap ad oP mer a AAA y y nT La S S aS gt S 1412 gt RET w Pole a e e RT 10sseT tuk asp The hinged wire wrap back panel is mounted on the mounting rack of the NetGuardian Note The hinged wire wrap back panel supports 18 26 AWG wire solid DPS Telecom recommends using 24 AWG wire solid The optional hinged wire wrap back panel p
26. 8 81 686 15_D8 Unit Address Subnet Mask Gdateway Backup Mode AbutoSwitch stWoitchToNeti ESC Enable Backup Mode to automatically switch between Netl and Net2 Backup Mode allows the NetGuardian to automatically switch between Netl and Net2 should LAN connectivity fall When used in Backup Mode the NetGuardian has 2 network connections attached but uses only the primary LAN Netl When a LAN failure occurs the unit makes the switch to the secondary LAN connection Net 2 to maintain visibility With the Autoswitch feature enabled the NetGuardian will revert back to the primary LAN connection when the uplink is re established 1 Login to the TTY interface and go to C onfig gt E dit 2 Goto E thernet gt NET 2 to configure the Net 2 Interface 3 Goto B ackup Mode to enable disable this mode then A utoswitch to use the automatic network switching feature 13 2 2 SFP Fiber Connection For Fiber Build Option For NetGuardian 1664 units with GigE Fiber top board you also can view and edit switch and SFP fiber connections in the TTY interface After logging in select M onitor gt sW itch to view details for the 10 100 1000BaseT switch and Fiber interface es Telnet 126 10 216 251 Password fet Guardian 1664 y5 2D 0032 ilmi Piroxy Toelnet Debug ethoit l Monitor Pding S tats Tune Modem Reset Port CESC 7 M Alarms FefLjays afNjalogs Event loy aflicum Timer EAC PoOing targets ptOorts sCWoitch Siystem afRip D
27. AM14 7 AM13 AM16 8 AM15 AM18 g AM17 AM20 10 AM19 AM22 11 AM21 AM24 12 AM23 AM26 13 AM25 AM28 14 AM27 AM30 15 AM29 AM32 16 AM31 AM34 17 AM33 AM36 18 AM35 AM38 19 AM37 AM40 20 AM39 AM42 21 AM41 AM44 22 AM43 AM46 23 AM45 AM48 24 AM47 GND 25 RTN Pinout Diagram for Discretes 1 48 Connector RTN is the alarm return pin Standard configurations have this pin tied to GND While it is possible to change this configuration to utilize different types of alarms i e TTL Open Collector Battery Closure the hardware must be ordered in that configuration It is NOT field adjustable 6 6 3 Analogs 1 6 9 16 Discretes 49 64 Pinout Diagram ALARMS 49 64 RELAY FA ANALOGS 1 6 9 16 I 26 AMA49 AMS0 AMS pening 2 AMS I AM54 E AM53 AMSG Ms 29 AMSS AMSR M55 o AMSI AMG 31 AMS9 AM6 3 AMGI AMG 33 AM63 ANAG 34 ANAQ ANA 10 35 ANAIO ANAII 36 ANAII ANA 2 3 ANAI2 ANA 13 38 ANAI3 ANA 14 9 ANAI4 ANA IS 40 ANAIS ANA 16 4l ANA G FANO y FACO 47 ANAI y ANAL ANA2 NAL a5 ___ANA2 ANA3 NA ag ANAJ ANA4 NAS 7 ANA4 ANASI ne ag ANAS ANAG NAS l9 ANAG GND ANAG ET BIAS Pinout Diagram for Analogs 1 6 9 16 Discretes 49 64 RTN is the alarm return pin Standard configurations have this pin tied to GND While it is possible to change this configuration to utilize different types of alarms i e TTL Open Collector Battery Closure the hardware must be ordered in that configuration It is NOT field adjustable
28. BLK BLK GRY GRY BLK YELIBLU BLUFYEL YEL ORG ORGEL YEL GRN GRN YEL YEL BRN BRN YEL YEL GRY GRY YEL VIOVBLU BLU VIO ORG ORG VIO VIO GRN GRN VIO VIO BRN BRN VIO VIOIGRY GRYNVIO ALM 1 ALM 2 ALM 3 ALM 4 ALM 5 ALM 6 ALM 7 ALM amp ALM 9 ALM 10 ALM 11 ALM 12 ALM 13 ALM 14 ALM 15 ALM 16 ALM 17 ALM 18 ALM 19 ALM 20 ALM 21 ALM 22 ALM 23 ALM 24 ALM 25 ALM 26 ALM 27 ALM 28 ALM 29 ALM 30 ALM 31 ALM 32 ALM 33 ALM 34 ALM 35 ALM 36 ALM 37 ALM 38 ALM 39 ALM 40 ALM 41 ALM 42 ALM 43 ALM 44 ALM 45 ALM 46 ALM 47 ALM 48 RTN GND 66 Block Pair 1 2 3 Eri Lee a di 11 12 13 14 15 16 17 18 19 20 21 oe 23 24 25 Corresponding 50 Pin Connector Pin 26 1 aT 2 28 a 29 4 40 5 31 6 32 T od 28 RTN is the alarm return pin Alarms on standard units are dry closure or ground closure Most units will have RTN internally tied to GND However special hardware assemblies may have RTN isolated from GND For details regarding your unit s hardware please reference the product description appendix 29 Corresponding 50 Pin Wire color 66 Block Connector wire stripe Connection Pajir Pin ALM 49 4 26 ALM 50 1 ALM 51 2 27 ALM 52 2 ALM 53 4 Bi ALM 54 3 ALM 55 4 29 ALM 56 4 ALM 57 5 30 ALM 58 5 ALM 59 31 ALM 60 6 6 ALM 61 7 32 ALM 62 7 ALM 63 8 33 ALM 64 8 ANA 9 9 a4 ANA 9 g ANA10 10 35 ANA10 10 ANA11 11 36 ANA11 11 ANA
29. Back Panel For 19 rack D PK NGPAN The Hinged Amphenol Back Panel easily allows for Upgrades from a KDA864 to a NetGuardian 1664 5 Specifications Discrete Alarm Inputs Analog Alarms Analog Input Range Analog Accuracy Ping Alarms Protocols Interfaces Max Dimensions Weight Mounting Power Input Voltage Options Include Current Draw GMT Fuse Sensor Power Output Voltage Output Options Output Current Input Current Draw GMT Fuse Modem Visual Interface 64 expandable to 112 or 160 16 94 to 94 VDC or 4 to 20 mA 1 of Analog Range See Analog Step Sizes 32 SNMPv1 SNMPv2c SNMPv3 DCPx DCPf TRIP SNPP SMTP TAP HTTP FTP TELNET ICMP RADIUS SSH HTTPS with Hardware Acceleration build option 9 RJ45 Yost serial ports 17 RJ45 ports with the 16S top board option 2 RJ45 10 100 full duplex Ethernet ports 1 port tied internally to switch if switch option is purchased 1 RJ11 telco jack 2 50 pin amphenol connectors discretes controls and analogs 1 4 pin screw connector analogs With Fiber top board build option 4 10 100 1000 copper Ethernet ports AND 2 1000 Base X SFP Fiber ports With D Wire top board build option 1 RJ11 D Wire port With WAN top board build option 1 Rj45 WAN port 1 75 H x 17 W x 12 75 D 4 5 cm x 43 2 cm x 32 4 cm 4 Ibs 3 oz 1 9 kg 19 or 23 rack 48 VDC nominal 36 to 72 VDC Optional 24 VDC nominal 18 to 36
30. FTP Read Write 1 1 GLD poller toggle switch Shows GLD polling 12 HTML debug switch Snows Web Browser processing 1 HWACS debug switch Shows hardware access operation PING toggle switch 1 1 1 LED toggle switch Shows current LED state L 17 LCD display toggle switch Snows LCD control and text 18 Modem toggle switch Shows modem vectored initialization 19 Undefined i and write operation and event posting O fa Undefined p e2 SPORT toggle switch Port init debug and channeled portdebug P e8 PPP toggle switch Shows PPP functioning S a ___ 24 QAccess toggle switch Reserved for future use O Qa 25 Undefined 0 1 2 3 4 5 Socket toggle switch Shows current dcu resources 6 7 8 26 Report toggle switch Shows reporting event activity including SNMP pagers email etc Also shows PPP negotiation for NG client PPP mode 27 SNMP toggle switch Reserved for future use S 28 STAK toggle switch Shows network processing and IPA of arp requests Also shows packets discarded by Filter IPA i 29 TERM toggle switch Shows UDP TCP port handling The camera and network time NTP jobs also use the TERM toggle switch 30 Undefined 31 HTTP toggle switch Shows handling of web browser packets 32 WEB toggle switch 2 Dump HTML text from web browser 60 61 Debug Input and Filter Options 14 Reference Section 14 1 Display Mapping Port Address D
31. Full Clear 46 Data 1 RevQ Full Clear ESC to exit Any key to continue_ System Alarms can be viewed from the M onitor menu gt S ystem option 13 3 1 5 Monitoring Data Port Activity View the status of the NetGuardian s 8 data ports from the M onitor menu gt p O rts option Enter the number of the port you wish to view and press Enter The NetGuardian provides an ASCII description under Transmit and Receive Choose a Transmit to view data transmitted to another device Choose b Receive to view data received from another device See Appendix ASCII Conversion for specific ASCII symbol conversion Allarms relfllays afNJalogs E vent log af C cum Timer BJAC Pjing targets plO rts s W itch System alR p D bg ESC 0 Data Port ID 1 9 1 a lransmit b Receive c Transmit HEX d Receive HEK ESC Data port activity can be viewed from the M jonitor menu gt p O rts option 13 3 1 6 Monitoring the Accumulation Timer The Accumulation Timer keeps a running total of the amount of time a point is in an alarm state An alarm point that exceeds a user defined threshold will trigger a Accumulation Event system alarm Refer to the figures below to define the accumulation timer 56 Config P rosy Telnet D ebug elklit Ejdit M onitor Ping S tats T une Modem Rjeset Port ESC H A larms Relays a N alogs Event log a C cum Timer BJAC Pling targets pl lrts S ystem ESC 7 C Accumulation limer enabled Display Reference 1 Point Refer
32. PA Proxy Base Analog Description Analog Display Unit Analog Major Under Threshold Analog Minor Under Threshold Analog Minor Over Threshold Analog Major Over Threshold Analog Trap Analog Primary Notification Analog Secondary Location Analog Polarity Analog Group Number Analog Reference 1 VD Analog Reference 1 Dis pla Analog Reference 2 VD Analog Reference 2 Displa Analog Deadband 2 udp tcp serial depx depf depe get set access 1 16 0000 01ff where Bit O 1 admin Bit 1 l database Bit 2 1 monitor Bit 3 l rly control Bit 4 1l reachthru Bit 5 1 modem Bit 6 1 telnet Bit 7 l sd_ monitor IP Address get set net 1 2 ipa get set net 1 2 subnet Subnet Gateway 1 32767 string 0 48 chars string 0 3 chars oe inca ve CO pm go go go get set alg 1 16 sec 0 16 get set alg 1 16 polarity 0 Normal 1 Reversed getset alg 1 16 group mju zmnu mno mjo 1 16 get set alg 1 16 trap O trap disabled 1 trap enabled get set alg 1 16 pri 0 16 getset alg 1 16 refl lll getset alg 1 16 ref2 get set alg 1 16 deadband 0 1 9 9 52 1 Reversed 1 trap enabled Notification Alarm Description get set alm base expl exp2 1 64 desc string 0 48 chars Alarm Secondary get set alm base expl exp2 1 64 sec 0 8 Notification LCD Delay Time for get
33. al database The local password database will only be used for front panel craft port access in the event the RADIUS configuration 1s making the unit otherwise inaccessible niYiram P PP Djate time R ADIUS Rjeboot ESC A 16 seconds 126 010 220 194 1812 IFace NET Secret thisisanewsecret Server 2 255 250 209 209 Disabled Port 1812 Face NET Secret default secret Rletry Tjimout ajIPAL b IPA2 c Portl d Port elIfacel f lIface g Secretl h Secret ESC _ The RADIUS configuration menu using the TTY interface Global Settings Retry How many times the RADIUS server will retry a logon attempt Time out Enter in the number of seconds before a logon request Is timed out Servers 1 2 Enter the IP address of the RADIUS server Port 1812 is an industry standard port for using RADIUS Use the drop down menu to choose between NET1 and NET2 Enter the RADIUS secret in this field Username dps user Password 322222 RADIUS logon screen prompts for a Username and Password 50 13 2 6 New TTY Command Mode This command line mode offers an alternate way of configuring the NetGuardian 1664 This interface is scriptable and is recommended for advanced users Entries are NOT case sensitive NetGuardian G5 HyperTerminal Tips for using TTY Command Mode TI gt TE e To enter command mode login to the TTY interface and press Ctrl C ot oe e To view all acceptable operations type get he
34. alogs connectors located on the back panel The NetGuardian 1664 s discrete alarm inputs and first six analog alarm inputs are connected through the two 50 pin connectors labeled Discretes 1 24 and Analogs 1 6 Discretes 25 32 on the back panel Analog alarm inputs 7 and 8 are connected through the four pin connector labeled Analogs 7 8 6 6 1 Alarm Connector Pinout Table Discretes 1 48 Analogs 9 16 js JS NIOJOAJA JOIN 10 16 apc La 22 Eom GND 25 Tar EMEN gt e EE E rs EE anom 0 Alarm and analog pinouts for NetGuardian 1664 8 S8 36 S9 O 7 6o 88 w j e 32 9 62 w 63 pat 64 e oat O B MA 8 6 AN 8 GND RIN is the alarm return pin Alarms on standard units are dry closure or ground closure Most units will have RTN internally tied to GND However special hardware assemblies may have RTN isolated from GND For details regarding your unit s hardware please reference the product description appendix ADC channels 4 5 6 and 8 may be unavailable for external use These analog channels are sometimes configured in hardware for monitoring A and B power feeds internal temperature and external temperature For details regarding your unit s hardware please reference the product description appendix 17 6 6 2 Discretes 1 48 Connector Pinout Diagram o AM2 1 AM1 AM4 2 AM3 AMG 3 AM5 AMB AM7 AM10 5 AMS AM12 6 AM
35. ar Trap Packets Tables 14 3 A and 14 3 B provide a list of the information contained in the SNMP Trap packets sent by the NetGuardian SNMP Trap managers can use one of two methods to get alarm information 1 Granular traps not necessary to define point descriptions for the NetGuardian or 2 The SNMP manager reads the description from the Trap 162 UDP Headers and descriptions 162 Destination port 69 Peers 1 3 6 1 2 1 1 6 0 1 3 6 1 4 1 2682 1 4 5 1 1 99 1 1 1 ee eee ee 1 3 6 1 4 1 2682 1 4 5 1 2 99 1 1 1 1 3 6 1 4 1 2682 1 4 5 1 3 99 1 1 1 1 3 6 1 4 1 2682 1 4 5 1 4 99 1 1 1 1 3 6 1 4 1 2682 1 4 5 1 5 99 1 1 1 1 3 6 1 4 1 2682 1 4 5 1 6 99 1 1 1 parm Vae SNMP Headers and descriptions 70 14 4 Trap SNMP Logic NET1 NET2 Trap Dest Rest O Gatewa Gatewa Gatewa Subnet 1 No Gatewa Trap SNMP Logic 14 5 ASCII Conversion The information contained in the table below is a list of ASCII symbols and their meanings Refer to the bulleted list below to interpret the ASCII data transmitted or received through the data ports Port transmit and receive activity can be viewed from the Web Browser Interface e Printable ASCII characters will appear as ASCII e Non printable ASCII characters will appear as labels surrounded by brackets e g NUL e Non ASCII characters will appear as hexadecimal surrounded by brackets e g LIF 1 e A received BREAK will appear as lt BRK gt Bel
36. ardian please call us at 559 454 1600 or e mail us at support dpstele com 15 1 General FAQs Q A gt How do I telnet to the NetGuardian You must use Port 2002 to connect to the NetGuardian Configure your Telnet client to connect using TCP IP not Telnet or any other port options For connection information enter the IP address of the NetGuardian and Port 2002 For example to connect to the NetGuardian using the standard Windows Telnet client click Start click Run and type telnet lt NetGuardian IP address gt 2002 How do I connect my NetGuardian to the LAN To connect your NetGuardian to your LAN you need to configure the unit IP address the subnet mask and the default gateway A sample configuration could look like this Unit Address 192 168 1 100 subnet mask 255 255 255 0 Default Gate way 192 168 1 1 Save your changes by writing to NVRAM and reboot Any change to the NetGuardian s IP configuration requires a reboot O When I connect to the NetGuardian through the craft port on the front panel it either doesn t work gt gt right or it doesn t work at all What s going on Make sure your using the right COM port settings Your COM port settings should read Bits per second 9600 9600 baud Data bits 8 Parity None Stop bits 1 Flow control None Important Flow control must be set to none Flow control normally defaults to hardware in most terminal programs and this
37. ated data port Data Ports 1 8 S Blink Red Receive over indicated data port NOTE Alarm must be configured for notification to be reflected in LED Front panel LED Status message descriptions 39 10 Back Panel LEDs V4AMPGMT 10 400 Mbps Switch il 2 3 4 r me Discretes 1 24 GLD ECU TELCO 101100 Back panel LEDs for Power left and Ethernet connections right F The back panel LEDs indicate the status of power and Ethernet connections LED status messages are described below te Ses Pesen Polarity is correct on power feed A oe and or B No Power or Polarity Reverse 10 100 Net Solid Green Link detected Blink Green ne or more of the Ethernet Switch ports are active aa eral iA Blink Green Activity over indicated integrated Ethernet Switch port Solid Green Link detected SFP Fiber 1000Base X Solid Red SFP detected no link Fiber build option only 1 2 Solid Green SFP detected link is up 10 100 1000 BaseT Flashing Activity on port detected Switch 1 4 Green Fiber build option only Solid Greenok Link detected Back panel LED Status message descriptions 40 11 Configuring the NetGuardian The NetGuardian must be provisioned with log on passwords alarm descriptions port parameters ping targets control descriptions and other system information You can provision the NetGuardian using either the NGEdit 1664 software or the Web interface The NetG
38. beyond dpsRTU adds another object identifying number For example the object identifier of the Display portion of the Control Grid is 1 3 6 1 4 1 2682 1 4 3 3 because the object identifier of dpsRTU is 1 3 6 1 4 1 2682 1 4 the Control Grid 3 the Display 3 dpsRTU2 1 3 6 1 4 1 2682 1 4 _OV_vTraps DisplayGrid ControlGrid NVRamGrid 0 1 2 3 4 5 DisplayEntry 1 NVRamSection 1 AlarmEntry 1 See Table 14 1 A Tbl B1 O OV Traps points Tbi B2 1 Identity points Tbi B3 2 DisplayGrid points _OV_vTraps Ident DisplayEntry 1 3 6 1 4 1 2682 1 4 0 1 3 6 1 4 1 2682 1 4 1 1 3 6 1 4 1 2682 1 4 2 1 PointSet 20 Manufacturer Port 1 1 1 2 SumPCIr 102 Com Restored 014 Must be setto 1 to perform the resync P0001 Set 10001 through fequest which will resend TRAPs for any P0064Set 10064 Standing alarm P0001Clr 20001 through PO064CIr 20064 PointClr 21 Model 2 Address kk 1 I ime Tbi B3 3 ControlGrid points ControlGrid 1 3 6 1 4 1 2682 1 4 3 int 1 3 6 1 4 1 2682 1 4 6 1 APoint 4 Address 2 Display 3 Value 4 Thresholds If Mj Mn is assumed 2 B Only supported on some older DPS devices 68 The NetGuardian OID has changed from 1 3 6 1 4 1 2682 1 2 to 1 3 6 1 4 1 2682 1 4 Hot Tip Updated MIB files are available on the Resource CD or upon request 14 3 SNMP Granul
39. cannot use configuration software to convert alarm points to TTL edge sensed operation TTL alarm pomts are a hardware option that must be specified when you order your NetGuardian Ordermg TTL points for your NetGuardian does not add to the cost of the unit What you can do with the configuration software is change any alarm point from Normal to Reversed operation Switching to Reversed operation has different effects depending on the kind of input connected to the alarm point e Ifthe alarm input generates an active high signal switching to Reversed operation means the NetGuardian will declare an alarm in the absence of the active high signal creating the practical equivalent of an active low alarm e Ifthe alarm input generates an active low signal switching to Reversed operation means the NetGuardian will declare an alarm in the absence of the active low signal creating the practical equivalent of an active high alarm e Ifthe alarm input is normally open switching to Reversed operation converts it to a normally closed alarm point e Ifthe alarm input is normally closed switching to Reversed operation converts it to a normally open alarm point O Every time my NetGuardian starts up I have to reenter the date and time How can I get the NetGuardian to automatically maintain the date and time setting A You have three options for keeping the correct time on your NetGuardian Real Time Clock Option You can order your NetGuardian
40. command The arrow cursor gt will move to the right of the colon in Contrast to indicate that the command submenu is selected Press the V or A button until you re satisfied with the contrast setting then press Sel to make your selection To exit the Command Menu and revert to the default contrast setting press Menu 37 8 Alarm Speaker The NetGuardian s alarm speaker emits distinctive tones under two conditions If there is an Ethernet connection failure the speaker will emit a high low warbling tone Press L any front panel button to silence the speaker 2 Ifan alarm occurs the speaker will emit an intermittent beep Press any front panel button to silence the speaker If you do not silence the speaker the beep will continue for the user defined duration default is a 6 second duration Silencing the speaker will allow the next alarm if any to sound 9 Front Panel LEDs 38 Front panel LEDs The NetGuardian s front panel LEDs indicate communication and alarm reporting status LED status messages are described below LE Status Description Blink Green Valid Configuration Contig Blink Red Invalid Configuration Blink Green Transmit over expansion port Expansion i Blink Red Receive over expansion port gt Blink Green Transmit over Ethernet port 2 e Blink Red Receive over Ethernet port 2 Craft Blink Green Transmit over craft port Blink Red Receive over craft port Blink Green Transmit over indic
41. current polling chain on the Master system NET not active The Neti LAN port is down Check LAN cable Ping to and from the NET not active The Net2 LAN port is down unit If not using Nett or Net2 set IP Subnet and Gateway to 255 s LNK Alarm No network connection detected Remove configured modem initialization An error has been detected during String then power cycle the unit If alarm modem initialization The modem did not persists try resetting the Modem port respond to the initialization string from the TTY interface or contact DPS for possible RMA The unit has not seen a poll from the Master for the time specified by the DCP Timer setting DCP Poller Inactive Modem not responding Define the IP Address where you would like to send SNMP trap events or NMP j S trap event occurred configure the event not to trap Check for failed notification events that may be filling up the pager queue There may be a configuration or communication problem with the notification events 11 45 Notification A notification event like a page or email Use RPT filter debug to help diagnose failed was unsuccessful notification problems Disconnect whatever device is connected 46 Craft Rcvo full ee eee ee to the craft serial port This alarm should was able to process not occur Modem RcvQ The modem port received more data than poe wnal Gi eounecing toing 47 NetGuardian This alarm should not full itwas able to proc
42. e MAC address of the destination device has been registered on the router s Address Resolution Protocol ARP table Enter the IP address of your gateway and your T Mon system to the ARP table What do the terms port address display and alarm point mean These terms refer to numbers that designate the location of a network alarm from the most general a port to which several devices are connected to the most specific an individual alarm sensor Port A number designating a serial port through which a monitoring device collects data Address A number designating a device connected to a port Display A number designating a logical group of 64 alarm points Alarm Point A number designating a contact closure that is activated when an alarm condition occurs For example an alarm point might represent a low oil sensor in a generator or an open close sensor in a door These terms originally referred only to physical things actual ports devices and contact closures For the sake of consistency port address display alarm point terminology has been extended to include purely logical elements for example the NetGuardian reports internal alarms on Port 99 Address 1 Q What characteristics of an alarm point can be configured through software For instance can point 4 be used to sense an active low signal or point 5 to sense a level or a edge The NetGuardian s standard configuration is for all alarm points to be level sensed You
43. ect proxy The 16S option can be ordered with the 12 24 VDC Sensor Power Supply which provides a convenient way to connect an auxiliary sensor to a battery power supply so if AC power goes down your sensor will still be powered Just plug the sensor into the back panel to use the sensor power supply See Section 6 8 4 for more information about the Sensor Power build option The 16S option also includes hardware acceleration SSL SSH For help accessing your NetGuardian s TTY interface via SSH see Establishing an SSH Session 27 6 8 7 D Wire Sensor Inputs The port on your NetGuardian labeled D Wire supports up to 16 D Wire sensors Your NetGuardian powers and communicates with your D Wire sensors via simple RJ 11 connection The max cable length depends on the number of sensors daisy chained together The cable lengths and corresponding number of sensors can be seen in the table below Maximum Cable Lengths Nodes Max ft Nodes Max ft Nodes Max ft Nodes Max ft 1 800 150 700 475 350 225 200 175 Maximum Cable Lengths O r O Note The DPS Temperature and Humidity Sensor DPS part number D PK DSNSR 12002 occupies two nodes 6 8 7 1 Connecting D Wire Sensors Using a standard 6P4C straight through RJ 11 cable part number D PR 045 10A 01 pinout below connect the D Wire port on the NetGuardian to the In jack on the D Wire Sensor Chain additional sensors to the D Wire sensor using the
44. ed is reversed the LED will not illuminate 7 Repeat Steps 2 4 for Power Connector B 8 Reisert the fuse to power the NetGuardian The front panel LEDs will flash RED and GREEN To connect the NetGuardian to a power supply using a WAGO connector follow these steps The Grounding Lug on the back of the unit provides a permanent connection to earth ground when connected The Grounding Lug must be used in order to comply with ce WARNING standards EARTH GROUND F hor i GNO gv GND A B FA Analogs 7 8 TP YAAMPGMT a F t m OG i si x ak re iw aa on ta lt pimin LR a Grounding Lug and Symbol 1 Remove the 2 fuses A amp B from the back panel of the NetGuardian Do not reinsert the fuses until all connections to the unit have been made 2 Remove the WAGO power connector Note that the plug can be inserted into the power connector only one way this ensures that the barrier plug can only be reinserted with the correct polarity Note that the 48V terminal is on Slots 1 and 3 and the GND terminal is on Slots 2 and 4 when counting from left to right 3 Use the grounding lug to connect the unit to earth ground The grounding lug is next to the symbol Insert the eyelet of the earth ground cable between the two bolts on the grounding lug Ground cable not included 4 Insert a battery ground into the power connector plug s slots 2 and 4 by pushing down on top of the appropriate slot of the
45. ence 11 Point Description Point Status Clear Event Threshold 00 01 01 dd hh mm Accumulated Time 00 00 00 dd hh mm Accumulated Since 22 July 2001 03 16 Rieset AccTmr ESC Monitor and reset the Accumulator Timer Field escription Display and Point Indicates which alarm point is to be monitored Reference Point Description The user defined description of the monitored alarm point Point Status The current status of the monitored point Event Threshold Amount of time allowed to accumulate before the system alarm Accumulation Event is triggered Note Maximum is 45 days Accumulated Time The total time the monitored point has been in an ALARM state Accumulated Since Indicates the last time the accumulation timer was reset a Selecting this option will reset the timer Field descriptions in the Accumulator Timer Settings 13 3 2 Viewing Live Target Pings Choose P ing to ping any of the NetGuardian s user defined IP addresses Then enter the ID number 1 32 of the IP address or enter any IP address to ping Ejdit M onitor Pling S tats T une Modem Rjeset Port ESC P Ping Address ID 1 32 Continuously ping an IP address that has been defined in the NetGuardian s ping table 57 13 3 3 Proxy Menu You can create proxy connections to reach through to the craft port modem port or any of the other eight serial ports from the P roxy menu You ll be able to monitor and control additional device
46. ess occur 48 Serial 1 RcvQ full 49 Serial 2 RcvQ full 50 Serial 3 RcvQ full Serial 4 RcvQ l l 51 full Serial port 1 or appropriate serial port Check proxy connection The serial port number receiver filled with 8 K of data 4 data may not be getting collected as e io K if BAC active expected u 53 Serial 6 Rcvo full 54 Serial 7 Revo full 55 Serial 8 RcvQ full Over 250 events are currently queued in the pager queued and are still trying to report Pager Queue Overflow System Alarms Descriptions continued 66 Display Points Alarm Point Description Solution Under Ports gt Options verify the number of configured NGDdx units Use EXP filter debug and port LEDs to help diagnose the problem Use DB9M to DB9M with null crossover for cabling Verify the DIP addressing on the back of the NGDdx unit NetGuardian NGDdx 2 Fail Expansion shelf 2 DX 2 Eo a communication link failure NetGuardian NGDdx 1 Fail Expansion shelf 1 DX 1 fail communication link failure Notused used EE just GLD unit 1 and attempt to poll Verify GLD is connected to data port 8 and the hardware is RS485 not RS232 Verify the GLD unit addressing and GLD 2 fal GLD address 2 is failed test GLD units individually on the GLD communication bus l Reduce the number of connected GLD i One or more GLD units addressed 3 l i i GLD 3 fail units to determine which unit may be through 12 may be failed
47. front panel that will include the Product Number Serial Number and MAC Addresses This will help you if you ever need to contact DPS about your device The barcode and serial number can be used to faciliate your internal tracking 2 About This Manual There are three separate user manuals for the NetGuardian 1664 the Hardware Manual which you re reading now the NGEdit1664 User Manual and the NetGuardian 1664 Web Interface User Manual This Hardware Manual provides instructions for hardware installation and using the TTY interface The NGEdit1664 and Web Interface User Manuals included on the NetGuardian Resource CD provide instructions for configuring the NetGuardian using the Windows based NGEdit1664 utility software or the Web Interface 3 Shipping List While unpacking the NetGuardian please make sure that all of the following items are included If some parts are missing or if you ever need to order new parts please refer to the part numbers listed and call DPS Telecom at 800 622 3314 ED ss ie ve LOLS OL erim Em e oo a NetGuardian 1664 D PK N1664 NetGuardian 1664 Hardware Manual D UM N1664 ff 7 rel on fe N gt a i gt ty A 7 N k OPS Telecom fy F ger i i NetGuardian 1664 Resource CD DB9M DB9F Download Cable 6 ft includes manuals MIBs and software D PR 045 10 A 04 gt A fj if MAN MAN Two Ethernet Cables 14 ft Telephone Cab
48. i i causing the link to fail 59 GLD 1 fail GLD address 1 is failed 1 Chan Port has not forwarded any traffic in the time specified by the Channel Chan Port Timeout Timer The channel feature Timeout forwards data between two ports so the NG may be used to analyze serial traffic using CHAN filter debug The Craft Timeout Timer has not been reset in the specified time This feature is designed so other machines may 63 Craft Timeout keep the TTY link active If the TTY interface becomes unavailable to the machine then the Craft Timeout alarm is set Change the data port type to OFF or set the Channel Timer to a different setting 2 Change the Craft Timeout Timer to 0 to disable the feature Enable DCP timestamp polling on the master so events are collected or reboot the system to clear the alarm System Alarms Descriptions continued The Event Que is filled with more than 64 Event Que Full Egg uncollected events 67 14 2 SNMP Manager Functions The SNMP Manager allows the user to view alarm status set date time issue controls and perform a resync The display and tables below outline the MIB object identifiers Table B 1 begins with dpsRTU however the MIB object identifier tree has several levels above it The full English name is as follows root iso org dod internet private enterprises dps Inc dpsAlarmControl dpsRTU Therefore dpsRTU s full object identifier is 1 3 6 1 4 1 2682 1 4 Each level
49. ian E16 D PK DXE16 Adding the NetGuardian E16 provides an additional 16 alarm pomts and 16 controls One NetGuardian E16 unit may be used per NetGuardian 1664 remote In this configuration the E16 must be the last unit in the chain Having only serial port it cannot forward traffic to a subsequent RTU ii E di i General LCD Display GLD D PK GLDRJ 12001 00001 The General LCD Display GLD is a small wall mounted remote terminal for the NetGuardian The LCD display shows system status and alarm messages and the built in speaker gives an audible notice of alarms Up to 12 GLDs can be daisy chained off the NetGuardian NetGuardian SiteMON IP D PK CAMRA The NetGuardian SiteMON provides security surveillance of remote sites The SiteMON connects to either the NetGuardian s integrated 10 100BaseT switch or a separate 10 100 1000 switch SiteMON images can be accessed directly from the SiteMON s Web Browser Interface or T GFX You can also mount the camera at harsh weather sites with the wide temp chassis design 40 42 4 tt viii m Hinged Wire Wrap Back Panel For 19 or 23 rack D PK NGPAN The hinged wire wrap back panel provides wire wrap connections for the NetGuardian s alarms and control relays Pluggable Barrier Panel For 19 or 23 rack D PK NGPAN The pluggable barrier panel provides screw lug barrier plug connections for the NetGuardian s alarms and control relays Hinged Amphenol
50. ian and to the DB9 on the hinged panel TM Se 4 vicar Bem maran CACACACACACACICA ERERERERERERERER EREREREREREZERCZ CZEREREAEREEEREE mes eee Vm 9 Close the back panel and lock it by turning the black swivel to the vertical position NOTE The connectors on the Hinged Pluggable Back Panel support 18 26 AWG wire stranded or solid DPS recommends using 24 AWG wire stranded 7 LCD Display Manu NetGuardian Front Panel LCD The front panel LCD displays the current alarm and control status and provides a command menu for controlling the NetGuardian s basic functions Using the LCD command menu The four buttons surrounding the front panel LCD are used to access the LCD Command Menu To access the menu press the Menu button To scroll the menu use the V and A buttons To select a menu command press the Sel Select button Standard Prompt When no Command Menu item is selected and no alarms or relays are active the LCD displays the firmware version and the standard prompt Press MENU for front panel options Controlling Display Speed The scroll speed can be temporarily increased by pressing and holding the A button while the message is active 7 1 Alarm and Control Status Messages If an alarm or control relay is active the LCD will display the followmg messages to indicate alarm and control status The LCD panel will display the following messages to indicate alarm and control status Discrete Alarms If there a
51. iby ESC 7 U Ethernet ID Link RA Pkts Ta Pkts Speed Active iBHMFULL 5917 1134 Down 4 A Down H A Active BMHALF 48 4813 Active iBHMFULL 1694 5863 Speed Ra Pkts T Pkts A H Active iBHAMFULL B 4768 Alarms reCLoays afNjaloygs Event loy atCtcum Timer BAG PoOing targets ptOorts s Woitch S ystem aftRip Dibg CESC F m SFP fiber connection detail in the TTY interface 47 13 2 3 Edit PPP Port Choose P PP to edit your baud rate depending on what device has been chose for the PPP port Config P roxy T jelnet D ebug elklit Ejdit Mjonitor Ping S tats Tjune Modem Rjeset Port ESC E E thernet n jram P PP Rjeboot siY stem ESC P Configuration Port Datal Baud 9600 Compression Yes Client Mode onl emand Phone Username Password Server Server Disabled Address 295 290 299 209 Client Specified Pjlort Blaud mo D Jem C ompression Mlode piHlone Ulsername pass Wlord SJerver Ajddress Bjaud mo Djem ESC Edit your PPP port If you are using a modem for the PPP port then choose mo D emto define the modem initialization strings Choose B aud to define the baud rate for that port Client Mode onDemand Phone Username Password Server Server Disabled Address 259 200 209 209 Client Specified Plort Blaud mo DJem C ompression Mlode piHjlone Uj sername pass WjJord SjJerver Ajddress Bjaud mo Djem ESC E 3 00 6 66 1 200 2 400 4 800 9 600 a 19200 b 38400 ESC Select
52. inged pluggable 2 Facing the back of the NetGuardian install the right side of back panel the NetGuardian 1664 should the hinged pluggable back panel Used the screws provided be rack mounted Suggestion Mount the to secure the right mounting arm to the rack unit in the flush rack mount position This means the front of the NetGuardian is flush with the front of the rack post 3 The rack should appear as shown above 4 Close the back panel gate and lock it in place by turning the black swivel to the vertical locked position as indicated on the silk screen 33 E ae CA KA 4 a 5 Attached the left side of the hinged panel 6 Unlock the back panel by turning the black swivel to the to the rack with the screws provided horizontal position Plug the amphenol cables in to the hinged back panel and secure them with the Velcro straps Make sure the NetGuardian s silk screen matches the hinged panel where the amphenols are connected gt 7 Tighten the 2 screws located to the right of 8 Use the remaining zip ties to keep the amphenol cords tied the amphenol cables Use the plastic zip together Trim the excess plastic off the zip ties with ties provided to secure both cables to the Scissors NetGuardian where shown bottom image Note A zip tie will be used on the NetGuardian s small metal tab to secure the left amphenol cable If your remote is equipped with the 4 pin analog connector connect it to the NetGuard
53. isplay Clear EN 9001 9064 poo 1 9065 9096 La 9129 9132 NN 9193 9196 Li 9257 9260 Ld 9321 9324 ae 9385 9388 i ia a NEZ Analog Channel 7 8513 8516 9513 9516 10 Analog Channel 8 8577 8580 9577 9580 System Alarms See table below 8641 8674 9641 9674 Display descriptions and SNMP Trap numbers for the NetGuardian i i The TRAP number ranges shown correspond to the point range of each display For example the SNMP Trap Set number for alarm 1 in Display 1 is 8001 Set for alarm 2 is 8002 Set for alarm 3 is 8003 etc The TRAP number descriptions for the Analog channels 1 8 are in the following order minor under minor over major under and major over For example for Analog channel 1 the Set number for minor under is 8129 minor over is 8130 major under is 8131 and major over is 8132 Expansion Unit Dis play Maps Port Address Display Description Set Clear 9 1 14 NetGuardian 480 as DX Alarms 1 64 6001 6064 7001 7064 9 1 15 NetGuardian 480 as DX Relays 1 4 6065 6069 7065 7069 el 1 155 NetGuardian 480 as DX Alarms 65 80 6081 6096 7081 7096 Display descriptions and SNMP Trap numbers for the NetGuardian 480 as an Expansion 62 Port Address Display Description Set Clear 1 14 NetGuardian DX48 Expansion 1 Alarms 1 48 6129 6177 7129 7177 NetGuardian DX48 Expansion 1 Relays 1 8 6193 6200 7193 7200 99 1
54. l need the following tools Phillips No 2 Screwdriver Small Standard No 2 Screwdriver Wire Strippers Cutter Wire Wrap Gun if hinged wire wrap panel is used Punch Down Tool if 66 blocks are used PC with NGEdit1664 software 6 2 Mounting The NetGuardian can be flush or rear mounted The NetGuardian mounts in a 19 rack or a 23 rack using the provided rack ears for each size Two rack ear locations are provided Attach the appropriate rack ears in the flush mount or rear mount locations shown in the figure above Note Rack ears can be rotated 90 for wall mounting or 180 for other mounting options not shown 11 6 3 Power Connection Power Die corporeal bear Rome A aed E Prg POWER ii A gri 0 734 max 4a GND a GHD FA Power connectors and The NetGuardian has two screw terminal barrier plug power connectors located on the left side of the back panel The Grounding Lug on the back of the unit provides a permanent connection to earth ground when connected The Grounding Lug must be used in order to comply with ce WARNING standards lt EARTH GROUND 7 j m ji pi A mE at i e oO A a FA Analogs 7 0 P Grounding Lug and Symbol Before you connect a power supply to the NetGuardian test the voltage of your power supply Connect the black common lead of a voltmeter to the ground terminal of the battery and connect the red lead of the voltmeter to the bat
55. le 6 ft D PR 923 10B 14 D PR 045 10A 01 23 Rack Ears 19 Rack Ears D CS 325 10A 01 D CS 325 10A 00 Eight 3 8 Ear Screws F Four Standard Rack Screws H 2 000 60375 05 1 000 12500 06 Four Metric Rack Screws G Thre 2 000 80750 03 2 741 00750 00 Two Large Power Connector Plugs for Main Power C Four Cable Ties 2 820 00862 02 Sixteen with hinged panel 1 012 00106 00 4 Pin Analog Connector D Pads E 2 820 00814 02 2 015 00030 00 A B C D E F G H Optional Hardware kit containing a WAGO connector Optional Items iP di Two 3 4 Amp GMT Accessory Fuses A 2 741 00250 00 External Temperature Sensor D PR 991 10A 07 One Small Connector for Sensor Output 2 820 00812 02 20 ft External Temperature Sensor D PK SENSR 12037 3 1 Port Allocation Located on the top of the unit in the back left corner is the Port Allocation Sticker This sticker includes your part number D PK NET1664 which specifies your build option The table below it lists your port allocation This label displays serial electrical information about each of the ports for example if the port hardware is configured for RS232 RS485 202 etc 4 Optional Accessories You can extend the capabilities of the NetGuardian through accessory units that provide greater discrete alarm capacity remote audiovisual alarm notification visual surveillance of remote sites and other options If you would like to order a
56. lp Radius Response Adwinistrative superuser Access Granted then press Enter NetGuardian 1664 v5 1F 0006 e Invalid commands will return Error as the response oui resi Tielet Dates ston e A CRLF is sent by the RTU following all responses from the RTU To enter Command Line mode login to the TTY then press Ctrl C e Limited data validation is in place using this method Use caution when setting variable values In some cases you need to reboot the NetGuardian for new variable values to take effect e Changing REF1 REF2 DISP1 or DISP2 affects the MAJOR MINOR OVER and UNDER alarm thresholds Changing any of these settings should be checked and re established as required e In the table below variables params are noted in brackets Operation i get help None Initialize NVRAM init nvram g2 None Write NVRAM None Read NVRAM None View System Up Time None View Firmware Version None Data Port Description string 0 15 chars Data Port Baud get set dataport 1 9 baud 1200 300 600 1200 2400 4800 9600 19200 38400 57600 1 15200 Data Port Format get set dataport 1 9 wfmt De msec msec crft cap ecu sps8 Expanders System Name string 0 31 chars string 0 31 chars string 0 31 chars string 0 20 chars Reboot DCP Unit ID DCP Port Number DCP Port Type DCP Protocol DCP Autonomous Time Network Time IPA Username Pass word Access Rights Network IPA Subnet Mask Gate way I
57. n investigate the ECU alarm source or don t associate notification with the alarm event Try pinging the Network Time Server s IP Address as it is configured Ifthe ping test is successful then check the port setting and verify the port is not being blocked on your network To turn off the feature under Accum Timer set the display and point reference to 0 Unplug the LAN cable and contact your network administrator Your network and the unit will most likely behave incorrectly After assigning a correct IP Address reboot the unit to clear the System alarm Check the back of the unit and confirm WAN cable is connected and WAN LED is solid green Will clear when fire and gas alarms clear Feature can also be disabled if Emergency Unlock Enabled is unchecked from the web or NGEdit interfaces Check D Wire port and D Wire Sensor and confirm cable is plugged in Also make sure that configured ROM ID s match the D Wire Sensors plugged in Seeing this alarm is normal if the unit is powering up Use Web or latest version of NGEdit1664 to configure unit Power cycle to see if alarm goes away May require RMA System Alarms Descriptions 65 Note Table continues on following pages Display Points Alarm Point _ Description If DCP responder is not being used then set the DCP Unit ID to 0 Otherwise try increasing the DCP timer setting under timers or check how long it takes to cycle through the
58. n s NVRAM Use FTP You can use File Transfer Protocol FTP to read and write configuration files to the NetGuardian s NVRAM but you can t use FTP to edit configuration files 15 2 SNMP FAQs Q A PO PE gt KO How do I configure the NetGuardian to send traps to an SNMP manager Is there a separate MIB for the NetGuardian How many SNMP managers can the agent send traps to And how do I set the IP address of the SNMP manager and the community string to be used when sending traps The NetGuardian begins sending traps as soon as the SNMP managers are defined The NetGuardian MIB is included on the NetGuardian Resource CD The MIB should be compiled on your SNMP manager Note MIB versions may change in the future The unit supports 2 SNMP managers which are configured by entering its IP address in the Trap Address field of Ethernet Port Setup You can also configure up to eight secondary SNMP managers which is configured by selecting the secondary SNMP managers as pager recipients Community strings are configured globally for all SNMP managers To configure the community strings choose System from the Edit menu and enter appropriate values in the Get Set and Trap fields Does the NetGuardian support MIB 2 and or any other standard MIBs The NetGuardian supports the bulk of MIB 2 Does the NetGuardian SNMP agent support both NetGuardian and T MonXM variables The NetGuardian SNMP agent manages an embedded MIB that support
59. n the LCD If no alarms are supported and are processed in active a no alarms active message will appear The LCD Delay Time is this order how long you want the points to show on the screen You can set the 1 Base Alarms delay time from 1 60 sec default is 2 sec This is configurable from the 2 Expansion 1 Alarms TTY command line interface web and NGEdit 1664 3 Expansion 2 Alarms 4 Expansion 3 Alarms Using the Front Panel LCD buttons for Point Mode 5 Ping Alarms Pressing the SEL A or V buttons will force the NetGuardian back into 6 Base Relays Scroll Mode for 3 minutes This is particularly useful for viewing the 7 Expansion Relays configured descriptions or analog values associated with the active alarms 8 Expansion 2 Relays When Point Mode is enabled but you chose to go into Scroll Mode press the MENU button twice to go back 9 Base Analogs 10 Expansion 1 Analogs 11 Expansion 2 Analogs 12 Network Link Down See section New TTY Command Mode for instructions on enabling disabling Point Mode 7 2 LCD Command Menu LCD display The LCD Command Menu provides commands for controlling some of the NetGuardian s basic functions temporarily silencing the alarm speaker rebooting the unit and running the TTY configuration utility When no Command Menu item is selected and no alarms or relays are active the LCD displays the firmware version and the Standard Prompt Press MENU for front panel options To acces
60. nector Pinout Diagram 6 6 3 Analogs 1 6 9 16 Discretes 49 64 Pinout Diagram 6 6 4 Analog Dipswitches 6 6 5 Integrated Temperature and Battery Sensor Optional 6 6 5 1 Analog Step Sizes 6 7 Data Ports 6 7 1 Connecting NetGuardian Accessories 6 7 2 GLD ECU Expansion Port RS 485 6 8 Hardware Options 6 8 1 Integrated 10 100BaseT Ethernet Switch Optional 6 8 2 Integrated T1 E1 Port 6 8 3 GSM GPRS or CDMA Wireless Modem Top Board Optional 6 8 4 12 or 24 VDC Sensor Power Supply 6 8 5 Hardware Acceleration SSL SSH 6 8 6 Integrated 8 Additional Serial Data Ports 6 8 7 D Wire Sensor Inputs 6 8 7 1 Connecting D Wire Sensors 6 9 Optional 66 Block Connector 6 10 Optional Hinged Wire Wrap Back Panel 6 10 1 Lexan Wire Wrap Cover 6 11 Optional Hinged Pluggable Back Panel 7 LCD Display 7 1 Alarm and Control Status Messages 7 2 LCD Command Menu 7 2 1 1 2 2 7 2 3 7 2 4 Sound off Reboot Run Config Contrast 8 Alarm Speaker 9 Front Panel LEDs 10 Back Panel LEDs 11 Configuring the NetGuardian 11 1 RADIUS Authentication Available as of Firmware 5 01 12 Connecting to the NetGuardian 12 1 Ma Craft Port 12 2 va LAN 13 TTY Interface 13 1 Establishing an SSH Session 13 2 Unit Configuration 13 2 1 13 2 2 13 2 3 13 2 4 13 2 5 13 2 6 Ethernet Port Setup 13 2 1 1 T1 E1 WAN Settings 13 2 1 2 New Backup Mode SFP Fiber Connection For Fiber Build Option Edit PPP Port Tune 202 Modem RADIUS Configuration New
61. ntatives who will give you the best in fast and accurate customer service To help us help you better please take the following steps before calling Technical Support 1 Check the DPS Telecom website You will find answers to many common questions on the DPS Telecom website at http www dpstelecom con support Look here first for a fast solution to your problem 76 2 Prepare relevant information Having important information about your DPS Telecom product in hand when you call will greatly reduce the time it takes to answer your questions If you do not have all of the information when you call our Technical Support representatives can assist you in gathering it Please write the information down for easy access Please have your user manual and hardware serial number ready 3 Have access to troubled equipment Please be at or near your equipment when you call DPS Telecom Technical Support This will help us solve your problem more efficiently 4 Call during Customer Support hours Customer support hours are Monday through Friday from 7 A M to 6 P M Pacific time The DPS Telecom Technical Support phone number is 559 454 1600 Emergency Assistance Emergency assistance is available 24 hours a day 7 days a week For emergency assistance after hours allow the phone to ring until it is answered with a paging message You will be asked to enter your phone number An on call technical support representative will return your call as
62. ny of these accessories or if you would like more information about them call DPS Telecom at 800 622 3314 AALE IER XADE cs ET JED DPS Telecom gt Grn Banks e Me Oa Red gt Points SUpport am D PK DX832 Craft ACK www dpstele com NetGuardian Expansion NetGuardian 832A 864A DX G5 D PK DX832 D PK DX864 The NetGuardian G5 expansions provide an additional 64 points for your 1664 Each expansion comes standard with an additional 8 control relays and 8 analog inputs and 1s available with an optional 8 port hub Optional builds are also available without controls analogs or both GEZ D PK NETOX Craft NetGuardian Expansion NetGuardian DX G4 D PK NETDX 12022 00001 The NetGuardian Expansion G4 provides an additional 48 discrete and 8 relay controls Up to two NetGuardian Expansions can be daisy chained off one NetGuardian On S amp g PYE g 123 4 6 6 7 8 Gm Banks 1234 ACK e vu ee Red Points NetGuardian dn0 Ee ci gi TT EP hamam atest te Raia kappan 1 H te Poe Ges ie orn tal T mart Breve dp iki er NetGuardian Expansion The NetGuardian 480 NG480 Expansion provides an additional 80 alarms and 4 relays With 80 discrete alarm inputs you can easily forward all the alarms of a small to medium sized site ee Pee ee ponpa atana pi i e ir 3 E NetGuardian E16 o 7 S oYrr sir suuuuuyu Bom St e ach bii were e i ee NetGuard
63. o manage your remote sites including built in alarm monitoring paging and email capabilities that can eliminate the need for an alarm master With the NetGuardian you can e Monitor 32 discrete alarms 32 ping alarms and 16 analog alarms e Control remote site equipment via 8 terminal server ports e Monitor your remote site from anywhere using the NetGuardian s built in Web Browser Interface e Report alarms to multiple SNMP managers or the T Mon NOC Alarm Monitoring System e Report alarms via LAN or dial up connection e Automatically send pager and email alarm notifications 24 7 e Connect multiple concurrent users via Telnet over LAN to telecom switches servers radios PBXs and other equipment e Monitor discrete and analog threshold alarms e Ping IP network devices and verify that they re online and operating e NEW Backup Mode Redundant LAN connectivity New The NetGuardian 1664 supports serial baud rates up to 115 200 additional RS485 for GLD ECU expansion polling port triple CPU speed for faster processing optional built in 4 port switch tied to NET2 optional external temperature sensor analog readings accurate to within 1 dual 10 100 NICs isolated replacing the 1OBaseT NICs SNMPv2c SNMP v2c Inform trap and SNMPv3 TIP This is the basic installation hardware manual For software and web configuration manuals please refer to appropriate manual on the Resource CD provided with your unit or visit www dpstele com
64. ort 1 You can also connect to the NetGuardian over a LAN connection This is a very convenient way to provision multiple NetGuardian units at multiple locations Note You don t have to be connected to a NetGuardian unit to use NGEdit1664 You only need a connection to the unit to read or write configuration files to its NVRAM You can use NGEdit1664 on an unconnected PC to create and store NetGuardian configuration files To connect to the NetGuardian via LAN all you need is the unit s IP address Default IP address is 192 168 1 100 Note NET is defaulted to 192 168 1 100 If you have physical access to the NetGuardian the easiest thing to do is connect to the unit through the craft port and then assign it an IP address Then you can complete the rest of the unit configuration over a remote LAN connection if you want For instructions see Section 12 1 Connecting to the NetGuardian via Craft Port If you DON T have physical access to the NetGuardian you can make a LAN connection to the unit by temporarily changing your PC s IP address and subnet mask to match the NetGuardian s factory default IP settings Follow these steps 1 Look up your PC s current IP address and subnet mask and write this information down 2 Reset your PC s IP address to 192 168 1 200 3 Reset your PC s subnet mask to 255 255 0 0 You may have to reboot your PC to apply your changes 4 Once the IP address and subnet mask of your computer coincide with the NetGua
65. ower to the wireless modem just remove the fuse You may use any service provider you choose for your wireless connectivity DPS Telecom has tested and recommends using CrossBridge Solutions CROSSBRIDGE a O L U TI N a www cross bridgesolutions com Phone 800 668 4368 Email info crossbridgesolutions com Below is a diagram of a connection scenario using CrossBridge 29 CDMA GPRS a CrossBridge Gateway Interface e lt a ai ay Simplified diagram of CrossBridge Connection 6 8 4 12 or 24 VDC Sensor Power Supply 12VDC 12 VDC sensor power supply You can order your NetGuardian 1664 with an optional 12 VDC or 24 VDC sensor power supply This provides a convenient way to connect an auxiliary sensor to a robust battery power supply so if AC power goes down your sensor will still be powered Just plug the sensor into the back panel to use the sensor power supply The two pin connector for the sensor power supply is a barrier plug connector similar to the main power connector To power an external sensor follow these steps L Remove the 1 4 amp fuse from the sensor power supply on the back panel of the NetGuardian Do not reinsert the fuse until all power connections to the external sensor have been made Remove the power connector plug from the sensor power supply Note that the plug can be inserted into the power connector only one way
66. pdfs op_ guides Stand alone local visibility You don t need an alarm master unit to monitor your site with the NetGuardian With the NetGuardian s built in Web Browser Interface you can access the NetGuardian view alarms and control remote site devices from any computer anywhere in your network 24 7 pager and email alerts no master needed Out of the box the NetGuardian supports 24 7 pager and email reporting Send alarms directly to maintenance technicians in the field even when no one s in the office Connect via LAN to telecom switches servers radios and more Each of the NetGuardian s eight serial ports can be individually configured to serve as a craft port a channel port or a TCP or UDP reach through port giving you LAN based terminal server access to up to eight serial devices NEW RADIUS Authentication As of firmware v5 01 Take the security of your alarm remotes to the next level with RADIUS authentication Now the NetGuardian 1664 can interact with your RADIUS server integrating it as part of your enterprise management Reports to multiple SNMP managers and T Mon NOC simultane ously The NetGuardian reports to both the T Mon NOC Alarm Monitoring System and any SNMP manager You can simultaneously forward alarms from the NetGuardian to T Mon NOC and multiple SNMP managers at multiple IP addresses Alarms can also be configured to dispatch to one some or all SNMP managers Your NetGuardian will come with a label on the
67. r details see the separate user manuals for the NetGuardian 1664 web browser and NGEdit 1664 12 Connecting to the NetGuardian 12 1 via Craft Port 4 NetGuardian Craft Port The simplest way to connect to the NetGuardian is over a physical cable connection between your PC s COM port and the NetGuardian s craft port Note You must be connected via craft port to use the TTY interface but you don t have to be connected to a NetGuardian unit to use NGEdit1664 You only need a connection to the unit to read or write configuration files to its NVRAM You can use NGEdit1664 on an unconnected PC to create and store NetGuardian configuration files Use the DB9M DB9F download cable provided with your NetGuardian to make a craft port connection Select the following COM port options 41 e Bits per second 9600 e Data bits 8 e Parity None e Stop bits 1 e Flow control None When a connection is established sometimes accompanied by receipt of a hex byte type DPSCFG press Enter to activate the configuration menu The default password is dpstelecom RADIUS As of firmware 5 01 typing lt CR gt will prompt for a username and password You can perform basic configuration via the craft port but if you like you can connect via the craft port just to configure the NetGuardian s Private LAN IP address and then do the rest of your configuration via a LAN connection 42 12 2 via LAN prp GLD ECU TELCO Ethernet p
68. r traps The NetGuardian alarm point descriptions are individually defined using the Web Browser TTY or NGEdit1664 configuration interfaces gt My SNMP traps aren t getting through What should I try Try these three steps 1 Make sure that the Trap Address IP address of the SNMP manager is defined If you changed the Trap Address make sure you saved the change to NVRAM and rebooted 2 Make sure all alarm points are configured to send SNMP traps 3 Make sure the NetGuardian and the SNMP manager are both on the network Use the NetGuardian s ping command to ping the SNMP manager 15 3 Pager FAQs Q Why won t my alpha pager work A To configure the NetGuardian to send alarm notifications to an alpha pager enter the data phone number for your pager in the Phone Number field This phone number should connect to your pager service s modem Then enter the PIN for your pager in the PIN Rcpt Port field You don t need to enter anything in any of the other fields If you still don t receive pages try setting the Dial Modem Init string to ATS37 9 This will limit the NetGuardian s connection speed Be sure to use the rpt debug feature if needed gt Numeric pages don t come in or are cut off in the middle of the message What s wrong You need to set a delay between the time the NetGuardian dials your pager number and the time the NetGuardian begins sending the page message You can set the delay in the Pager Number field
69. rdian s you can access the NetGuardian via a Telnet session or via Web browser by using the NetGuardian s default IP address of 192 168 1 100 5 Provision the NetGuardian with the appropriate information then change your computer s IP address and subnet mask back to their original settings 43 13 TTY Interface The TTY interface is the NetGuardian s built in interface for basic configuration From the TTY interface you can e Edit the IPA subnet and gateway e Set DCP info for T Mon polling e Configure primary port e Ping other devices on the network e Set unit back to factory defaults e Debug and troubleshoot For more advanced configuration tools please use the Web Browser Interface For Telnet connect to the IP address at port 2002 to access the configuration menus after initial LAN WAN setup Telnet sessions are established at port 2002 not the standard Telnet port as an added security measure If you re using Windows 7 then you ll need to install telnet before you can use the TTY interface To install telnet open up your command line type cmd into the search bar in the Start Menu Select cmd exe to run the command line mi C Windows system32 cmd exe _ build impl xml HM_Ref_ContextPop_MapFiles xml HM Advanced CommandLine INL xml From the command line type in pkgmgr iu TelnetServer then press enter When the command prompt appears again the installation is complete
70. re any standing discrete alarms the display will read Discrete Alarms followed by the user defined descriptions of the standing alarm points Relays If there are any latched relays the display will read Relays followed by the user defined descriptions of the latched relays Ping Alarms If any ping targets have failed to respond within the specified time the display will read Ping Alarms followed by the user defined descriptions of the ping targets Analogs If any analog channels have crossed a threshold value the display will read Analogs followed by the user defined description of the analog channel the channel s last voltage reading and a letter indicating which threshold the channel has crossed Analog thresholds are represented by the following characters Major Over a capital O Minor Over a lower case 0 Minor Under a lower case u Major Under a capital U 35 New LCD Function Point Mode This new feature allows you to change the way active alarms are displayed on the NetGuardian s front panel LCD screen When the LCD is in Point Mode only the display points in alarm are displayed on the screen instead of the full alarm descriptions Pomt numbers for discrete alarms analog threshold crossings and latched relays will appear on the LCD Point Mode is configurable from the TTY command line interface the web browser and NGEdit 1664 The following windows are Only windows with alarms will appear o
71. rovides wire wrap connections for the NetGuardian s alarms To connect alarms to the wire wrap panel follow these steps 1 Mount the hinged wire wrap back panel on the mounting rack of the NetGuardian 2 Close the hinged back panel and lock in place by turning the black plastic locking swivel to the vertical position 3 Connect discrete alarms and analog alarms to the two pin blocks 31 For the NetGuardian 1664 Shown with point 5 wired 10 RET 20 RET 30 RET 31 RET 41 RET 51 RET RET 11 RET 21 RET DISCRETES DISCRETES ANALOGS B DISCRETES L 61 64 RET CONTROLS N O COM Suggested Wire Wrapping Tools Hand Wrap Tool Wire Wrap Gun Electrical Wire Wrap Gun 6 10 1 Lexan Wire Wrap Cover Spacer Lexan panel Securing screw oo Lexan panel assembly To attach the Lexan cover to the hinged wire wrap panel follow these steps 1 Attach communication lines to the wire wrap pins before connecting the Lexan cover 2 Attach the Lexan cover to the mounting clips and connect to the hinged panel 32 6 11 Optional Hinged Pluggable Back Panel fy yi AATA Y A Sa AAS ee H d Lg 4 gt oh we da a T e A AZAL Silk screen on the Hinged Pluggable Back Panel indicates which way to turn the black swivel to lock and unlock the gate Instructions for installing the Hinged Pluggable Back Panel Rear View i i 1 To begin installing the h
72. s only the NetGuardian s RTU variables The T MonXM variables are included in the distributed MIB only to provide SNMP managers with a single MIB for all DPS Telecom products How many traps are triggered when a single point is set or cleared The MIB defines traps like major alarm set cleared RTU point set and a lot of granular traps which could imply that more than one trap is sent when a change of state occurs on one point Generally a single change of state generates a single trap but there are two exception to this rule Exception 1 the first alarm in an all clear condition generates an additional summary point set trap Exception 2 the final clear alarm that triggers an all clear condition generates an additional summary point clear trap What does point map mean A point map is a single MIB leaf that presents the current status of a 64 alarm point display in an ASCII mone readable form where a represents a clear and an Moon x represents an alarm Q The NetGuardian manual talks about eight control relay outputs How do I control these from my SNMP manager A The control relays are operated by issuing the appropriate set commands which are contained in the DPS control grid For more information about the set commands see Appendix Display Mapping in any of the NetGuardian software configuration guides 75 How can I associate descriptive information with a point for the RTU granula
73. s the Command Menu press the Menu button 7 2 1 Sound off Sound Off command 36 Sound off The Sound off command suppresses sounds from the alarm speaker for a user defined period of 10 20 or 30 minutes To scroll to the next menu command press the V button To change the Sound off setting press Sel to select the command The arrow cursor gt will move to the right of the colon in Sound off to indicate that the command submenu is selected Press the W and A buttons to scroll through the Sound off time period options Select 0 minutes to allow all sounds When the time period you want is displayed press Sel to make your selection To exit the Command Menu without changing the Sound off setting press Menu 7 2 2 Reboot Reboot command Reboot The Reboot command reboots the NetGuardian Press Sel The LCD will briefly display the message Rebooting and the normal boot sequence will begin To exit the Command Menu without rebooting press Menu 7 2 3 Run Config Run Config command Run Config The Run Config command forces the TTY configuration interface to run over the craft port at the user defined baud rate default is 9600 baud To run the TTY configuration utility press Sel To exit the Command Menu without running the TTY interface press Menu 7 2 4 Contrast Contrast The Contrast command provides controls for adjusting the contrast of the LCD To adjust the contrast press Sel to select the
74. s via proxy connection to the NetGuardian Data presented and handshaking will be specified by the connected device To cancel the proxy connection wait a half second then quickly type and press ENTER Config Pjroxy Tjelnet Dlebug elklit Available Data Ports In use 1 2 3 4 3 6 7 8 8 Proxy to M odem 1 2 3 4 5 6 7 8 ESC Access devices connected to the eight data ports on the back panel through Monitor menu gt P roxy option 13 3 4 Event Logging Choose E vent log to view the up to 100 events posted to the NetGuardian including power up base and system alarms ping alarms and analog alarms Posted events for the various alarms include both alarm and clear status Refer to the table below for event log field descriptions Note All information in the event log will be erased upon reboot or a power failure 58 assword Fw eee eae ead etGuardianil664u 5 HA onfiy Piroxy Telnet Debug etait dit M onitor Pjiny Stats Tune Modem Reset Port ESC 7 A larms Relays atNjaloys E vent loy atlicum Timer EAC Fring targets ptOorts Siystem ESC E ut Date Time Grp State PRef Description i 64 26 2666 16 82 16 1 setgrpi 11 597 GLD BSU i Fail 2 81 81 2645 12 68 68 i clrgrpl 11 33 Unit Reset 3 81 81 2645 12 00 00 i setgrpi 11 33 Unit Reset 4 61 61 2661 12 68 66 1 setgrpi 9 3 MjuU 7 5 61 61 2661 12 66 06 i setgrpi 7 1 Mn gt 6 61 61 2681 12 66 64 1 setgrpi 11 39 NET 2 is not Active
75. same straight through cables from the Out jack on the previous sensor to the In jack on the next Le Out on sensor 4 to In on sensor 5 6 5 VCC 4 GND 3 Data 2 GND 1 Pinout for the NetGuardian and D Wire Sensor RJ 11 jacks For details about configuring your sensors through the web interface see the Sensors section of this web browser user manual 6 9 Optional 66 Block Connector Both of the 50 pin connectors on the back panel of the NetGuardian can be connected to the optional 66 block 25 pair block part number D PR 966 10A 00 See the figures below for pinout and color code information for Discretes 1 48 Discretes 49 64 Relays 1 8 and Analogs 1 6 Note The 66 Block supports termination of 22 26 AWG 0 81 0 41mm solid insulated cable or 18 19 AWG 1 02 0 91mm solid stripped cable DPS recommends using 24 AWG wire solid Note If connecting to a 50 pair split block all connections should be made on the two pin columns closest to the right hand side of the block m b E E b eal ES EE man Gin amam mama m na SS ih GE nu SG nn nn n a a ni dn 66 Block connections for Discretes 1 48 Wire color wire stripe Connection WHT BLU BLUAWHT WHT ORG ORG WHT WHT GRN GRN WHT WHT BRN BRANWHT WHT GRY GRY WHT RED BLU BLU RED RED ORG ORG RED RED GRN GRN RED RED BRN BRN RED RED GRY GRY RED BLK BLU BLU BLK BLK ORG ORG BLK BLK GRN GRN BLK BLK BRN BRN
76. sensor analog channels Your integrated sensors each occupy one of the unit s 16 analog channels The table above lists the analog channels used for the integrated temperature and battery sensor Note that these options are factory pre set based on your build options and cannot be adjusted 6 6 5 1 Analog Step Sizes Analog Step Sizes Your Analogs are accurate to within 1 of the analog range Analog Step Sizes and Accuracy Input Voltage Range Resolution Step Size 0015 V 05V zv osv ev Analog step sizes and accuracy 21 6 Data Ports 48V GND 48V GND A B FA Analegsyg T M Analogs 1 5 Discretes 25 Data ports I amp The NetGuardian s eight data ports provide reach through terminal server functionality for connecting multiple simultaneous users to external equipment via Telnet over LAN Each port can function as a proxy connection to an external device a craft port a channel port a TCP or UDP reach through port The NetGuardian can support simultaneous proxy connections for up to eight users NOTE See Section 6 8 6 if you have the 16S serial port build option Yost RS 232 RJ45 Connector Yost RS 485 RJ45 Connector 8 RTS Request to Send 8 TX Transmit 7 DTR Data Terminal Ready 7 N C Not Connected 6 TXD Transmit Data 6 RX Receive 5 GND Ground 5 GND Ground 4 GND Ground 4 GND Ground 3 RXD Receive Data 3 RX Receive 2 DSR Data Set Ready 2 N C Not Connected
77. session Behaviour Translation Saved Sessions Selection Colours D efault Settings Load Connection Proxy Telnet Rlogin SSH d Close window on exit O Always OO Never Only on clean exit Cas Use PuTTY to establish an SSH session with your NetGuardian 13 2 Unit Configuration 13 2 1 Ethernet Port Setup You must assign your NetGuardian s IP address before you can connect via LAN WAN using a Telnet client or a Web browser To connect via LAN the minimum configuration requires setup of the IP address and subnet mask Minimum WAN configuration requires that you set the default gateway as well 45 EM Telnet 10 0 4 64 NetGuardianl664 v5 4k HH8SH Config Proxy Telnet Debug ethoit Edit M onitor Ping Soitats Tdune Modem Reset Port ESC 7 E Ethernet ntUdoram PPP Doatertime RCASDIUS Reboot ESC 7 E Global WET i gt WMET 2 gt CESC 7 i Net i Interface Unit Address 816 6000 AMA Abd 616 600 664_664 gt Subnet Mask 255 255 860 688 1255 255 HAH HHA Default Gateway 616 666 666 254 Ain MAR 00h 2547 Link Status Detected MAC Address 8H 18 81 68_ 76 BC nit Address S ubnet Mask Goiateway ESG 7 Configure the Ethernet port parameters To assign the NetGuardian s Ethernet Settings 5 Type C for the C onfig menu 6 Type E for E dit menu 7 Type E for port settings 1 for Net 1 2 for Net 2 8 Configure the unit address subnet mask and default gateway 9 ESC to the main menu 10 When
78. set Icddelay 1 60 sec Point Mode Examples e You want to find out how long this NetGuardian has You want to see the alarm description for Base been running since last rebooted Get system Alarm 1 To see the description type get alm base uptime by typing get sysuptime then press Enter 1 desc NetGuardian G5 HyperTerminal NetGuardian G5 HyperTerminal File Edit View Call Transfer Help File Edit View Cal Transfer Help Username radius admin ieramen ESME Silim Radius Response Administrative superuser Access Granted NetGuardian 1664 v5 1F 0006 Radius Response Administrative superuser Access Granted NetGuardian 1664 v5 1F 0006 C onfig P roxy T elnet D ebug eflklit et alm base 1 desc gt g GENERATOR RUN e You want to set the Global Trap IP Address to e You want to change the LCD mode from Scroll 126 10 230 133 To enter this type set trap 1 ipa default to Pomt Mode To change this type set 126 10 230 133 Icdmode point Se on ees eg ce File Edit Yiew Call Transfer Help File Edit View Call Transfer Help a S8 Hil amp Username radius_admin Radius Response Administrative superuser Access Granted NetGuardian 1664 v5 1F 0006 NetGuardian 1664 vwb 1k 0006 NetGuardian A dps telecom C onfig P roxy Telnet D ebug e X it gt set trap 1 ipa 126 180 230 133 Cjonfig Pjroxy Tjelnet Djebug a gt set lcdmode point 53 13 3 Monitoring 13 3 1 Monitoring
79. tery s 48 VDC terminal The voltmeter should read between 36 and 72 VDC If the reading is outside this range test the power supply If your NetGuardian has the 24 VDC power connection option then the voltmeter should read between 18 and 36 VDC If your NetGuardian has the 12 VDC power connection option then the voltometer should read between 11 and 18 VDC To connect the NetGuardian to a power supply follow these steps L Remove the fuse from the back panel of the NetGuardian Do not reinsert the fuse until all connections to the unit have been made Remove the power connector plug from Power Connector A Note that the plug can be inserted into the power connector only one way this ensures that the barrier plug can only be reinserted with the correct polarity Note that the 48V terminal is on the left and the GND terminal is on the right 3 Use the grounding lug to connect the unit to earth ground The grounding lug is next to the symbol Insert the eyelet of the earth ground cable between the two bolts on the grounding lug Ground cable not included Insert a battery ground into the power connector plug s right terminal and tighten the screw Insert a 48 VDC line to the plug s left terminal and tighten its screw 12 6 Push the power connector plug firmly back into the power connector If the power feed is connected correctly the LED by the connector will light GREEN If the polarity of the power fe
80. the baud rate for your PPP port iii B 13 2 4 Tune 202 Modem Tuning the 202 modem on a NetGuardian 1664 can only be done from the TTY interface using either HyperTerminal through the front craft port or by telnet over LAN on port 2002 9600 bps HyperTerminal File Edit View Cal Transfer Help Password 2222222623 NetGuardian v3 20 0010 Cjonfig P roxy T elnet D ebug e K it E dit Mjonitor P ing S tats T une Modem R eset Port ESC T Tune Modem Port 1 4 ESC _ Press T to tune the 202 Modem with the TTY interface Though no menu options will appear use the following commands to tune the 202 modem Each menu option when chosen will output the character A on screen 1 Minor Adjust DB 2 Minor Adjust DB 3 High Frequency 4 Low Frequency 5 Off 6 Major Adjust DB 7 Major Adjust DB 8 Median Frequency Average of high and low frequency After selecting an option like 1 in this example for Minor Adjust the DB level the NetGuardian will return a command to inform you the task is completed Each time you hit a number key 1 8 the NetGuardian will a on your screen 49 13 2 5 RADIUS Configuration The TTY interface can also be used to configure RADIUS settings After entermg the IPA for the RADIUS server users will be prompted for both a username and password to logon to the unit This username and password combination will be verified against the RADIUS database and not the loc
81. this ensures that the barrier plug can only be reinserted with the correct polarity Note that the positive terminal is on the left and the negative terminal is on the right Connect the appropriate leads to each of the plug s screw terminals and tighten the screws Push the power connector plug firmly back into the sensor power supply connector Reinsert the fuse to power the external sensor 26 6 8 5 Hardware Acceleration SSL SSH If you ordered your NetGuardian with hardware acceleration then your NetGuardian is capable of SSL SSH connections For help accessing your NetGuardian s TTY interface via SSH see Establishing an SSH Session For help configuring your NetGuardian s web interface for SSL HTTPS connections see the Ethernet Ports section of the NetGuardian Web Interface manual 6 8 6 Integrated 8 Additional Serial Data Ports You can order your NetGuardian 1664 with the 16S build option This option gives you 8 extra serial data ports for a total of 16 serial data ports total to provide extra reach through capacity to control your external serial devices Serial Server Ports NOTE Uses same pinout as ports in 6 7 The first 7 serial ports can be used concurrently while the remaining 9 are pooled together and can be accessed at a time through the TTY interface or by proxy connection to the 8th serial port Connect your serial devices via RS232 or RS485 and access the devices through either through direct or indir
82. twsed fo Not used Timed Tick Exp Module Callout Network Time Server Accumulation Event Duplicate IP Address WAN Disconnected ECU Emergency Unlock D Wire Sensor Not Detected Power Up Lost Provisioning Toggles state at constant rate as configured by the Timed Tick timer variable Useful in testing integrity of SNMP trap alarm reporting Alarm is triggered whenever an alarm point from an Entry Control Unit ECU is collected A notification event may be associated with the alarm to force a call out or trap Communication with Network Time Server has failed An alarm has been standing for the time configured under Accum Timer The Accumulation timer enables you to monitor how long an alarm has been standing despite system reboots Only the user may reset the accumulated time a reboot will not The unit has detected another node with the same IP Address WAN Top Board is present but the WAN connection is not detected Set when both user defined fire and gas alarms occur A configured D Wire Sensor is not detected The unit has just come online The set alarm condition is followed immediately by aclear alarm condition The internal NVRAM may be damaged The unit is using default configuration settings 64 To turn the feature off set the Timed Tick timer to 0 Disable Building Access Control BAC by setting the BAC Unit ID to 0 If Building Access is being used the
83. uardian also supports a limited TTY interface for configuring some basic options For full instructions on configuring the NetGuardian see the software configuration guides on the NetGuardian Resource CD You can provision the NetGuardian either locally through the craft port or remotely through a LAN connection However to access the NetGuardian via LAN you must first make a temporary connection to the NetGuardian and assign it an IP address on your network For more information see Section 12 Connecting to the NetGuardian 11 1 RADIUS Authentication Available as of Firmware 5 0l RADIUS Remote Authentication Dial In User Service 1s an industry standard way to manage logins to many different types of equipment in one central location The NetGuardian connects to your central RADIUS server Every time a device receives a login attempt usually a username amp password it requests an authentication from the RADIUS server If the username amp password combination is found in the server s database an affirmative access granted reply is sent back to the unit device allowing the user to connect Also included in the reply are the user s individual access rights so different users can be granted different privilege levels If the user s login attempt is not found a rejection 1s returned instead RADIUS configuration for the NetGuardian will be achieved via the web browser interface NGEdit 1664 software utility and or TTY interface Fo

NetGuardian 1664

Contents

Download Pdf Manuals

Related Search

Related Contents