SX1016 User Manual
Contents
1. Some national and or local codes may require IT components to be bonded and exter nally grounded not including the power cord ground You must follow all national ad and local codes when installing this equipment 4 1 4 Cable Installation All cables can be inserted or removed with the unit powered on To insert a cable press the con nector into the port receptacle until the connector is firmly seated The orange LED indicator cor responding to each port will light when the physical connection is established that is when the unit is powered on and a cable is plugged into the port with the other end of the connector plugged into a functioning port After plugging in a cable lock the connector using the latching Mellanox Technologies 27 Rev 1 2 Installation mechanism particular to the cable vendor When a logical connection is made the green light will come on When data 1s being transferred the light will blink green Cables in the middle row should be inserted up side down in relation to the how the cables are inserted in the top row 5 To remove disengage the locks and slowly pull the connector away from the port receptacle The LED indicator will turn off when the cable is unseated Care should be taken not to impede the air exhaust flow through the ventilation holes next to the data connection ports Cable lengths should be used which allow for routing horizontally around to the side of the chassis before bendin2. All connectivity is via the connector side panel All connectors can support active cables 3 1 1 LED Assignments 3 1 1 1 System Status Indicators The System Status Indicators are located on the left side of the front connector side panel The system status indicators should display as follows When the switch is plugged in within four minutes the following LEDs should be evident The Status LED A should light up green The Fan LED e should light up green The Bad Port LED EJ should be off TheUnit ID LED should be off Figure 5 Status LEDs Mellanox Technologies 15 Rev 1 2 Hardware Basic Operation and Installation If the status LED shows red after four minutes unplug the switch and call your Mella nox representative for assistance If the fan LED shows red unplug the switch and call your Mellanox representative for assistance If the switch shuts down due to over temperature unplug the switch wait 5 minutes and replug in the switch For more information See Troubleshooting on page 31 3 1 1 2 Status LED The status indicator is located on the left side of the front panel connector side of the unit The following status conditions are possible Table 3 Switch Status LED Configurations LED Configuration LED Description Off No power to the switch Solid Green OK the switch is running All OK Blinking Green Switch is booting
3. Screw the Switch Slide to the Switch 39 Figure 20 Transfer Power Cord Finished 39 Mellanox Technologies 5 Rev 1 2 List of Tables Table 1 Revision History Table 2 4c ews au Ge de x ea Bae 7 Table 2 Reference Documents 8 Table 3 Switch Status LED Configurations 16 Table 4 Fan LED Configurations cse Ip ye pin de x ERE one ER 16 Table 5 Bad Port LED Configurations anne ERR ia ET a 1 Table 6 Port Connector Physical and Logical Link Indications 18 Table 7 Installation Kit According to Rack Size 21 Table 8 SX1016 Specification Data 5 248848 a TES 33 Table 9 SEPSPITOUL ids tara b totu nee we E es RV e sme de 41 Table 10 Replacement Parts Ordering Numbers 43 6 Mellanox Technologies SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Revision History Table 1 Revision History Table Date Revision Description November 2012 Rev 1 2 Removed Updating FW section not needed for Ethernet switches October 2012 Rev 1 1 e Added China CCC Warning Statement Fixes to port to LED assignment February 2012 Rev1 0 Initial release Mellanox Technologies 7 Rev 1 2 About this Manual This manual describes the installation an
4. Features i n a re be A area tee eto nda IE 10 1 2 Serial Number and Product Version Information 11 Chapter 2 Installation Safety Warnings 12 Chapter 3 Hardware Basic Operation and Installation 15 3 1 Switch Platform Hardware Overview 15 3 1 1 LED Assignments 15 3 1 2 Port Connector LED Assignment 18 3 2 A AR SA a A A a a NAO 18 3 3 SFP Cable Power Budget Classification 18 34 Intertaces s sus ze ple D REY AIR dena eX 19 3 4 1 Port Connector Interfaces 19 3 5 Management and Firmware Updating Interfaces 19 3 5 1 RJ 45 Console Connector 19 3 5 2 Mini US Biss ir ebd dere dapi At ides 19 3 5 8 RJ 45 Ethernet Connector 19 3 5 4 120 Connector 20 Chapter 4 Installation 44444484 veu me a ee ee n e 21 4 1 Package Contents and Installation 21 4 1 1 Installing the Switch in the Rack 21 4 1 2 Power Connections and Initial Power On 26 4 1 8 Grounding the Switch 27 4 1 4 Cable Installation 27 41 5 Cable Orientation sce so
5. Rev 1 2 Appendix F Avertissements de s curit d installation French 1 Instructions d installation Lisez toutes les instructions d installation avant de brancher le mat riel la source d alimentation lectrique L3 40 lbs 40 70 lbs 70 121 lbs gt 121 lbs lt 18 kgs 18 32 kgs 32 55 kgs gt 55 kgs 3 Temp rature excessive Ce mat riel ne doit pas fonctionner dans une zone avec une temp rature ambiante d passant le maximum recommand de 45 C 113 F Un flux d air de 200LFM A cette temp rature ambiante maximale est n cessaire En outre pour garantir un bon coulement de l air laissez au moins 8 cm 3 pouces d espace libre autour des ouver tures de ventilation 4 Empilage du ch ssis Le ch ssis ne doit pas tre empil sur un autre mat riel Si le ch ssis tombe il peut pro voquer des blessures corporelles et des d gradations de biens 5 Systeme de fusible neutre double p le cordons d alimentation avant d ouvrir le boitier de ce produit ou de toucher un de ses lm Avertissement Systeme de fusible neutre double p le Veuillez debrancher tous les AA composants internes 6 Orages dangers lectriques Pendant un orage il ne faut pas utiliser le mat riel et il ne faut pas brancher ou d brancher les c bles Mellanox Technologies 43 J Rev 1 2 7 Branchement d branchement des c bles InfiniBand en cuivre tres attention en les branchant et en les d branchant
6. air flow is specified in the product model number See Mellanox Part Numbering Legend on page 9 3 3 SFP Cable Power Budget Classification This switch is designed for active cables with a max power per module of 1 0W 18 Mellanox Technologies J SwitchX 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 3 4 Interfaces 3 4 4 Port Connector Interfaces The Connector side of the switch has 64 SFP 10 Figure 7 Port Numbering 1 4 7 10 13 16 19 22 25 28 35 38 41 44 47 50 53 56 59 62 2 5 8 11 14 17 20 23 26 29 31 33 36 39 42 45 48 51 54 57 60 63 3 6 9 12 15 18 21 24 27 30 32 34 37 40 43 46 49 52 5558 61 64 3 5 Management and Firmware Updating Interfaces There are two interfaces to connect to the SX1016 1X 100M IGb Ethernet connectors labelled connector that is labelled Use this RJ 45 connector to connect to the host PC Figure 8 Management Interfaces 3 5 1 RJ 45 Console Connector The port labelled is for a local host connection to the management module This is used the first time the switch is connected A harness is included in the package to connect to a DB9 connection on a host PC Before any remote management is available you must connect to a local host PC and follow the instruc
7. booting up Status LED and Fan LED If the fan LED is red make sure that the ambient temperature is within the range specified in the specification section of the appendix If any of the LEDs are red after 4 minutes unplug the switch and call your Mellanox representa tive Power supply unit 1 Check that the power cable has a voltage within the range of 100 240 volts AC 2 Remove and reinstall the power cable The green power LED for the fans does not come on Caution Do not run the switch if the System Status LED for the Fans is red or off The connector LED for the port connector does not come on 1 Check that both ends of the cable are connected 2 Check that the locks on the ends are secured 3 Make sure that the latest firmware version is installed on both the cards and the switch 4 If media adapters are used check that the all connections are good tight and secure The connector LED is flashing orange 1 Check that the Subnet Manager has been started 2 Check the cable is connected properly at both ends 3 Check that the cable is good 4 Check that the connections are good no cable weight on the connector no twists in the cable at the connector etc 5 Check the port connectors at both ends The switch is off Unplug the switch Wait 5 minutes Plug in the switch If the switch does not come on check the power supply If the switch comes on use the management software to determine
8. both sides of the switch power side and connector side are at the same level in the rack 6 Clip 4 more caged nuts into the holes on the opposite side of the rack Check that both sides of the switch left and right are the same level in the rack 7 Slide the rail into the rail slide 8 Using two of the bolts for each corner install the rails and rail slides in the rack Do not tighten the bolts yet Mellanox Technologies 25 Rev 1 2 Installation Figure 14 Slide the Rail into the Rail Slide This side of the rail kit goes on the side of the rack you will slide the switch into This 1s the same side of the switch that will be next to the vertical support 9 Slide the switch into the rails 10 Tighten the bolts to 9 2 Nm or 81 5 pound inches 11 Put the switch into place and screw the bolts into the nuts Tighten the bolts to 9 2 Nm or 81 5 pound inches 12 Ground the switch 13 Plug in the power cables 14 Check the Status LEDs and confirm that all of the LEDs show status lights consistent with normal operation Warning Any yellow or red status LEDs are cause for concern and must be dealt with immediately It can take up to 5 minutes to boot up during which time the status LED may indicate red 15 You can start connecting all of the cables to the switch 4 1 2 Power Connections and Initial Power On Each PSU has a separate AC receptacle The input voltage is auto adjusting for 90 264 VAC 50 60Hz powe
9. des connecteurs Consultez le fab Les c bles InfiniBand en cuivre sont lourds et ne sont pas flexibles il faut donc faire A ricant des c bles pour conna tre les mises en garde et les instructions sp ciales 8 Montage et entretien sur baie ciales pour s assurer que le syst me reste stable En g n ral il faut remplir la baie avec Lorsque ce produit est mont ou entretenu sur baie il faut prendre des pr cautions sp A du mat riel de bas en haut 9 Forts Courants de Fuite High Leakage Current Attention Forts courants de fuite Il est essentiel de relier a la terre avant de brancher l alimentation 10 Ajouter une information de connexion la masse Connect a Valid Ground to this Device terre du terminal de l appareil doivent tre appliqu es l installation de protection la Avant de brancher l appareil la conduite d alimentation les vis de protection la A Terre du b timent 11 Installation du mat riel h Ce mat riel ne doit tre install remplac ou entretenu que par du personnel form et qualifi 12 Elimination du mat riel L limination de ce mat riel doit s effectuer dans le respect de toutes les l gislations et r glementations nationales en vigueur 13 Codes lectriques locaux et nationaux LA Ce mat riel doit tre install dans le respect des codes lectriques locaux et nationaux 44 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User M
10. este producto o tocar cualquier componente interno 50 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 7 Cuando hay rayos peligro de descarga el ctrica No utilizar el equipo ni conectar o desconectar cables durante per odos de actividad de rayos 8 Conexi n y desconexi n del cable Copper InfiniBand Dado que los cables de cobre InfiniBand son pesados y no son flexibles su conexi n a A A los conectores y su desconexi n se deben efectuar con mucho cuidado Para ver adver A tencias o instrucciones especiales consultar al fabricante del cable 9 Montaje y mantenimiento de bastidores Al instalar o realizar el mantenimiento de este aparato en un bastidor es preciso adop tar precauciones especiales para garantizar que el sistema se mantenga estable En gen eral en un bastidor los equipos se deben instalar comenzando desde abajo hacia arriba 10 Instalaci n de equipos La instalaci n el reemplazo y el mantenimiento de este equipo estar n a cargo nica mente de personal capacitado y competente 11 Asegurar confinamientos adecuados El fabricante del producto final o el usuario final deber n suministrar La un confinamiento adecuado para componentes el ctricos y mec nicos y contra incen dio 12 Eliminaci n de equipos La eliminaci n definitiva de este equipo se debe efectuar conforme a todas las leyes y reglamentaciones nacionales
11. rails See Figure 11 Mounting Options Will the connector side be recessed past other equipment in the rack and will this be problematic The installation kit allows for a 2 recess of the switch past the vertical support Mellanox Technologies 23 Rev 1 2 Installation Figure 11 Mounting Options Vertical Support Connector side Rack door Power sid Connector side ower side 4 Power side Connector 7 side Rack door Power side Connector side 3 Decide which mounting option you want to use To use the rail kit to transfer the power cord from the connector side to the power side go to Transferring the Power Cord Section Appendix C 4 Screw the switch slides onto the switch Use 5 flat head screws for short switches and 7 screws for standard depth switches to connect each switch slide 24 Mellanox Technologies SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Figure 12 Screwing on the Rail 5 screws per side are needed for the short switch 7 screws per side are needed for the standard switch Figure 13 Inserting the Caged Nuts Side you will slide the switch into Second side led dol U ofoffo jo Mol okeke 5 Clip 6 caged nuts into the holes in the rack on the side of the rack you will be sliding the switch into Check that
12. sure the ESD strap is touching your skin and that the other end is connected to a verified ground 2 Choose which side of the switch you want even with the rack vertical support Either the side with the power supply units or the side with the SFP connectors can be even with one of the vertical rack supports Things to consider before choosing where to mount the rails and rail slides 22 Mellanox Technologies J SwitchX 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Figure 10 Placement of Switch in Hack Doors Cable with recommended bending radius 19 482 6mm Connector side Switch Spine side Doors Insufficient room for recommended bending radius Things to consider before choosing where to mount the rails and rail slides The distance between the rack and the door can be as little as 4 cm on one side of the rack and as much as 18 cm on the other side of the rack Keep in mind that there can be as many as 3618 cables connected to the switch The distance between the rack and the door can be as little as 4 cm on one side of the rack and as much as 18 cm on the other side of the rack Keep in mind that there can be as many as 64 data cables plus 1 management cable plus 1 serial cable connected to the switch Do you want the connector side recessed in the rack to allow for a larger cable bending radius It is possible to recess the connector side by 5cm by optional placement of the switch
13. the cause of the shutdown Check the temperature of the switch Check the ambient air temperature to make sure it is not too high Check the Fan status 9o c4 gy EA wm o Ro Mellanox Technologies 31 Rev 1 2 Troubleshooting The switch is not working and unresponsive Unplug the switch Wait 5 minutes Plug in the switch 1 2 3 4 Ifthe switch does not come on check the power supplies 5 Ifthe switch comes on use the management software to determine the cause of the shutdown 6 Reset the switch 32 Mellanox Technologies J Table 8 SX1016 Specification Data SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Appendix A Specification Physical Size Size SX1016B 1 716 1U H x 16 85 W x short 16 2 D 43 6mm X 427 9mm X 410 9mm Weight Center of Grav Short 7 82kg 2 PSUs ity As measured from the Connector Weight a side left side bottom corner Center of Gravity TED Short 21 6mm X 214mm X 218 8mm R Mounting Mounting 19 Rack mount SerDes Speeds Connector SerDes Speeds 10 Gb s per port Types SFP Connector Types Air Flow Heat dissipa pas 59 3 CEM tion 685 84BTUs hr Heat dissipation Maximum Power and Environmental Input Voltage Input Voltage Management Management 90 264 VAC 50 60Hz CPU PowerPC 460EX CPU CPU Power Typ Typ Consumption PS unit fan is always at 70 10GigE Active Cabl
14. up Red Error there is a problem with power output from the power supply or there is a thermal shut down 3 1 1 3 Fan Indicators e The fan indicator is located on the left side of the front panel connector side of the unit The fol lowing fan status conditions are possible Table 4 Fan LED Configurations LED Configuration FAN LED Off There is no power to the fans Green OK the fans are running Red Error the fans are not operating properly Replace the switch 16 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 LA Fans must be operating while the power supply is plugged in If the switch shuts down due to over temperature unplug the switch wait 5 minutes and replug in the switch For more information See Troubleshooting on page 31 3 1 1 4 Bad Port LED The bad port indicator 1s located on the left side of the front panel connector side of the unit The following bad port conditions are possible Table 5 Bad Port LED Configurations LED Configuration Description Off OK all ports are up and running Flashing Orange Error one or possibly more ports has just received a symbol error This LED shows symbol errors Possible causes for this are badcable badconnection bad connector This LED lights up when one or more ports is receiving a symbol error The LED immediately goes off until
15. with a minimum length of 1 5m six feet but no longer than 4 5m For European connection select a power supply cord that is internationally harmonized and marked lt HAR gt 3 conductor minimum 1 0 mm 2 wire rated at 300 V with a PVC insulated Jacket The cord must have a molded plug rated at 250 V 10 A 17 Do Not Use the Switch as a Shelf or Work Space Caution Slide rail mounted equipment is not to be used as a shelf or a work space The rails are not intended for sliding the unit away from the rack It is for permanent instal lation at final resting place only not used for service and maintenance 18 WEEE Directive According to the WEEE Directive 2002 96 EC all waste electrical and electronic equipment EEE should be collected separately and not disposed of with regular household waste Dispose of this product and all of its parts in a responsible and environmentally friendly way Mellanox Technologies SwitchX 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 3 X Hardware Basic Operation and Installation 3 1 Switch Platform Hardware Overview Figure 4 shows the front view of the switch The figure shows port configurations for the switch systems interface connectors and various status LEDs Figure 4 Switch System Front Panel SX1016 55
16. 13 C digos el ctricos locales y nacionales LA Este equipo se debe instalar conforme a los c digos el ctricos locales y nacio nales Mellanox Technologies 51 Rev 1 2 14 Cable de alimentaci n homologado por UL y con certificaci n CSA En conexiones de Am rica del Norte seleccionar un cable de alimentaci n homologado por UL y con certificaci n CSA de tres conductores 16 AWG termi nado en un enchufe moldeado con capuch n de 125 voltios nominal 13 A con una longitud m nima de 1 5 metros pero no m s de 4 5 metros En conexiones europeas seleccionar un cable de alimentaci n armonizado internacionalmente y marcado lt HAR gt de tres conductores hilo de 1 0 mm2 como m nimo 300 voltios nominal con cobertura protectora aislante de PVC El cable debe tener un enchufe moldeado con capuch n de 250 voltios nominal 10 A 15 A adir conexi n a tierra Antes de conectar el dispositivo a la l nea de alimentaci n los tornillos del terminal de la puesta a tierra de protecci n del dispositivo se deben conectar a la puesta a tierra de protecci n de la instalaci n del edificio Informaci n de conexi n a tierra La instalaci n del edificio deber prover un medio para la conexi n con la puesta a tierra de protecci n y un t cnico de servicio deber conectar permanentemente el equipo a dicho medio de conexi n Un T CNICO DE SERVICIO comprobar si la toma el ctrica de la que se suminis trar c
17. 1U 1 1 5U 2 2U FF of 40Gb s Ports equivalent 16 G Line rate of the fastest port X 10GbE Separator Power supplies 2 2 power supplies number of power supplies shipped with the basic sys tem M Depth of the Unit B short depth Y Air Flow direction R Connector side to PSU side airflow F PSU side to connector side airflow R Chip Generation R SwitchX S SwitchX 2 Mellanox Technologies 9 Rev 1 2 Overview 1 Overview The SX1016 is an economical high performance 64 port 10GbE switch providing 1 28Tb s of line rate performance Based on Mellanox s SwitchX silicon and innovative hardware design the switch packs 64 SFP interfaces in an ultra dense 1U form factor The SX1016 features industry leading latency of 250ns and power of less than 1 0W per port providing optimal per formance and efficiency for enterprise data center financial services Web 2 0 High Performance Computing and cloud computing applications Basic installation and hardware maintenance is covered in Hardware Basic Operation and Installation on page 15 Figure 1 SX1016 Switch 1 1 Features The SX1016 supports the following features 64 SFP ports of 10 Gb s upto 24 native Fiber Channel ports Two management options Supports Mellanox PPC460 Mezzanine CPU Supports Mellanox X86 Mezzanine CPU 2250W AC DC fixed Power supplies 6 Fixed Fans with 5 1 redundancy On board t
18. 250 V 10 A 15 Ableitstrom 3 5mA LEAKAGE gt 3 5mA WARNUNG Hohe Ableitstrom Earth Verbindung bevor Sie die Verbindung von wesentlicher Bedeutung werden 16 Add GND Verbindung Informationen Bevor Sie dieses Ger t an das Stromnetz die Schutzerde Terminal Schrauben dieses Ger t muss an den Schutzleiter in der Geb udeinstallation 17 Installation Codes Dieses Ger t muss installiert sein entsprechend auf die neueste Version des Landes i National Electrical Code F r Nordamerika m ssen in bereinstimmung mit den gel LA tenden Vorschriften in der US amerikanischen National Electrical Code und dem Canadian Electrical Code 18 Zusammenschaltung von EINHEITEN Kabel f r den Anschluss an das Ger t RS232 und Ethernet Schnittstellen m ssen UL zertifiziert Typ DP 1 oder DP 2 Hinweis wenn nicht mit Wohnsitz in LPS Schal LA tung berstromschutz Eine leicht zug ngliche Auflistung Abzweigleitung berstrom Schutzeinrichtung 20 A bewertet werden m ssen in dem Geb ude Verkabelung 19 Zweipolige bzw Neutralleiter Sicherung im Netzteil Achtung Zweipolige bzw Neutralleiter Sicherung im Netzteil Netzstecker ziehen um sicher zustellen da keine Spannung am Ger t anliegt Entfernen Sie alle Netzkabel vor dem ffnen der Abdeckung dieses Produkts oder dem Ber hren der Innenteile 48 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 20 Bodily Injury Due
19. Installation This equipment should be installed replaced and or serviced only by trained and qual ified personnel 11 Equipment Disposal h Disposal of this equipment should be in accordance to all national laws and regula tions 12 Local and National Electrical Codes This equipment should be installed in compliance with local and national electrical LA codes 13 Installation Codes This device must be installed according to the latest version of the country national electrical codes For North America equipment must be installed in LA accordance to the applicable requirements in the US National Electrical Code and the Canadian Electrical Code Mellanox Technologies 13 Rev 1 2 Installation Safety Warnings 1 4 14 Interconnection Of Units Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL L certified type DP 1 or DP 2 Note when residing in non LPS circuit Overcurrent Protection A readily accessible Listed branch circuit overcurrent protective device rated 20 A must be incorporated in the building wiring 15 Suitable Enclosure Suitable electrical mechanical and fire enclosure shall be provided by the L end product manufacturer and or the end user 16 UL Listed and CSA Certified Power Supply Cord For North American power connection select a power supply cord that is UL Listed and CSA Certified 3 conductor 16 AWG terminated with a molded plug rated at LA 125 V 13 A
20. Mellanox TECHNOLOGIES SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual P N MSX1016X 2BFR MSX1016X 2BRR Rev 1 2 www mellanox com Rev 1 2 NOTE THIS HARDWARE SOFTWARE OR TEST SUITE PRODUCT PRODUCT S AND ITS RELATED DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES AS IS WITH ALL FAULTS OF ANY KIND AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE THE PRODUCTS IN DESIGNATED SOLUTIONS THE CUSTOMER S MANUFACTURING TEST ENVIRONMENT HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE PRODUCTO S AND OR THE SYSTEM USING IT THEREFORE MELLANOX TECHNOLOGIES CANNOT AND DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST QUALITY ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT INDIRECT SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY FROM THE USE OF THE PRODUCT S AND RELATED DOCUMENTATION EVEN IF ADVISED OF THE POS
21. Produkt nicht wenn diese Abdeckung nicht sicher Dieses Produkt verf gt ber eine Abdeckung ber dem Bereich f r die redundante A festsitzt oder entfernt wurde 5 Bei Gewitter Elektrische Gefahr Arbeiten Sie w hrend eines Gewitters und Blitzschlag nicht am Ger t schlie en Sie keine Kabel an oder ab 6 Anschlie en Trennen von InfiniBand Kupferkabel an die Anschl sse angebracht bzw davon getrennt werden Lesen Sie die speziellen InfiniBand Kupferkabel sind schwer und nicht flexible Deshalb m ssen sie vorsichtig A Warnungen und Anleitungen des Kabelherstellers 7 Gafahr des elektrischen Schocks frei Um alle Einhieten spannungsfrei zu machen sind die Netzstecker aller Netzteile zu Gafahr des elektrischen Schocks Entferrnen des Netzsteckers elnes Netzteils spannungs A entfernen 46 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Risk of electric shock and energy hazard The PSUs are all independent Disconnect all power supplies to ensure a powered down state inside of the switch plat form 8 Rack Montage und Wartung sichtsma nahmen zu ergreifen um die Stabilit t des Systems zu gew hrleisten Im Wenn dieses Produkt in einem Rack montiert oder gewartet wird sind besondere Vor A Allgemeinen sollten Sie das Gestell von unten nach oben mit Ger ten f llen 9 Ger teinstallation Diese Ger t sollte nur von geschultem und qualifiziertem Personal
22. SIBILITY OF SUCH DAMAGE Mellanox TECHNOLOGIES Mellanox Technologies Mellanox Technologies Ltd 350 Oakmead Parkway Suite 100 Beit Mellanox Sunnyvale CA 94085 PO Box 586 Yokneam 20692 U S A Israel www mellanox com www mellanox com Tel 408 970 3400 Tel 972 0 74 723 7200 Fax 408 970 3403 Fax 972 0 4 959 3245 O Copyright 2012 Mellanox Technologies All Rights Reserved Mellanox Mellanox logo BridgeX ConnectX CORE Direct InfiniBridge InfiniHost amp InfiniScale amp PhyX SwitchX Virtual Protocol Interconnect and Voltaire are registered trademarks of Mellanox Technologies Ltd Connect IB FabricIT MLNX OSTM ScalableHPCTM Unbreakable Link UFM and Unified Fabric Manager are trademarks of Mellanox Technologies Ltd All other trademarks are property of their respective owners 2 Mellanox Technologies Document Number 3727 SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Contents Contents rs a a an iaa ae 3 List OF FlQUres sete tected wine ea a aros ee 5 Listiof Tables enfers ic ta ea as rar a ue 6 REVISION HISIOTV cord A AN 7 About this Manual aio aaa a ek sl 8 intended Audience 0000 a a ta a a aa 8 Related Documentation 8 Conventions EIE e etd RER ae RAR Pa ee et 8 Mellanox Part Numbering Legend 9 Chapter 1 Overview eu nr a RR ah Se eG Ree ERR Cena wee 10 13
23. anual Rev 1 2 14 Codes d installation pays Pour l Am rique du Nord l quipement doit tre install conform ment aux L appareil doit tre install selon l ancienne version des codes lectriques nationaux du A sp cifications du Code Electrique National Am ricain et du Code Electrique Canadien 15 Interconnexion des unites Les c bles de branchement l unit RS232 et les interfaces Ethernet doivent tre certi fi s UL de type DP 1 ou DP 2 Note lorsqu il existe dans un circuit non LPS Protection contre la surintensit Un appareil de protection r pertori facilement accessible contre la surintensit du circuit de branchement et calibr 20A doit tre incorpor dans le c blage lectrique du b timent 16 S assurer que les enceintes sont appropri es Des enceintes lectriques m caniques et incendie adapt es doivent tre fournies par le fabricant du produit final ou par l utilisateur final 17 Cordons lectriques CA homologu s UL Pour les prises lectriques en Am rique du Nord choisissez un cordon lectrique homologu UL et certifi CSA 3 conducteurs 18 AWG termin par une fiche moul e d une tension nominale de 125 V 15 A avec une longueur minimale de 1 5 m 6 pieds et d une longueur maxi male de 4 5 m 18 pieds Pour les prises lectriques en Europe choisissez un cordon lectrique harmonis inter nationalement et marqu lt HAR gt 3 conducteurs d un
24. cal codes in Denmark The AC cord shall have an integral ground wire and can only be plugged into a fully grounded outlet LA Do not connect this unit to any outlet that is not fully grounded Finland A Laite on liitett v suojamaadoituskoskettimilla varustettuun pistorasiaan e Norway Apparatet m tilkoples jordet stikkontakt Unit is intended for connection to IT power systems for Norway only Sweden A Apparaten skall anslutas till jordat uttag Mellanox Technologies 53
25. d basic use of the Mellanox SX1016 switch which is based on the SwitchX switch device Intended Audience This manual is intended for users and system administrators responsible for installing and setting up the switch platforms listed above The manual assumes familiarity with Ethernet Networks and Architecture Related Documentation Additional Documentation available from Mellanox Table 2 Reference Documents Switch Firmware and See Firmware Update http www mellanox com gt Support gt Download Firmware Tools Tools Conventions Throughout this manual the name SX1016 and the term switch are used to describe the 64 port SFP 10Gb s switch unless explicitly indicated otherwise The following icons are used throughout this document to indicate information that is important to the user Y This symbol signals recommendations to the user p This symbol indicates information that is helpful to the user p This symbol indicates a situation that can potentially cause damage to hardware or software BEWARE This symbol indicates a situation that can potentially cause personal injury or damage to hardware or software 8 Mellanox Technologies SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Mellanox Part Numbering Legend Place Field Decoder M Mellanox Technologies SX System Type SwitchX silicon Protocol 1 2 3 4 Ethernet C Height of Unit 0
26. dered at no extra charge e 1 X Harness HAR000028 Harness RS232 2M cable DB9 to RJ45 e X Quick Start Guide 1 X China RoHS statement If anything is damaged or missing contact your customer representative immediately For customer support go to www mellanox com gt Support gt Customer Support Portal Login 4 1 1 Installing the Switch in the Rack Tools and Customer Supplied Parts Phillips Screwdrivers 1 and 2 grounding screw ESD strap grounding wire sufficient to reach a valid ground ESD mat 4 1 1 1 Installation Kits There are two installation kit options One long and one short Both the long and the short instal lation kit can be used with this switch Table 7 Installation Kit According to Rack Size Kit OPN Rack Size MSX60 BKIT 40 60 cm MSX60 SKIT 60 80 cm For racks from 60cm to 80cm deep either use the standard depth switches with the long rail kit or the short switches with the long rail kit Mellanox Technologies 21 Rev 1 2 Installation Parts included in the rail kit 2 rails 16 recessed flat head screws for the standard switch 2 rail slides 10 caged nuts 2 switch slides 10 pan head screws M6 Figure 9 Rack Rail Kit Parts Switch slide Rail Rail slide 44484 x EA RAR KT ALL 26888 au a A e E ss CX 1 Place the ESD mat on the floor where you will be working and put on the ESD strap Make
27. diam tre de fil minimum de 0 75 mm2 d une tension nominale de 300 V avec une gaine isol e en PVC Le cordon doit avoir une fiche moul e d une tension nominale de 250 V et d une intensit nominale de 10 A 18 La Directive WEEE Conform ment la Directive WEEE 2002 96 EC les d chets d quipements lec triques et lectroniques EEE doivent tre tri s et ne peuvent tre limin s avec les d chets m nagers Veuillez disposer de ce produit et de tous ses composants de mani re responsable et respectueuse de l environnement Mellanox Technologies 45 Rev 1 2 Appendix G Installation Sicherheitshinweise German 1 Installationsanleitungen Lesen Sie alle Installationsanleitungen bevor Sie das Ger t an die Stromversorgung anschlie en 2 bertemperatur Dieses Ger t sollte nicht in einem Bereich mit einer Umgebungstemperatur ber der maximal empfohlenen Temperatur von 45 C 113 F betrieben werden Es ist ein Luft LA strom von 200 LFM bei maximaler Umgebungstemperatur erforderlich Au erdem sollten mindestens 8 cm 3 in Freiraum um die Bel ftungs ffnungen sein um einen einwandfreien Luftstrom zu gew hrleisten 3 Stapeln des Chassis Das Chassis sollte nicht auf andere Ger te gestapelt werden Wenn das Chassis herun terf llt kann es zu Verletzungen und Besch digungen an Ger ten f hren 4 Redundanter Stromversorgungsanschluss Elektrische Gefahr Stromversorgung Betreiben Sie das
28. e Clock Line 4 6 MOD_ABS Module Absent Grounded within the module 4 7 RSO No connection required 8 RX_LOS Loss of Signal indication Logic 0 indicates normal operation 9 RSI No connection required 10 VeeR Receiver Ground Common with Transmitter Ground 11 VeeR Receiver Ground Common with Transmitter Ground 12 RD Receiver Inverted DATA out AC Coupled 13 RD Receiver Non inverted DATA out AC Coupled 14 VeeR Receiver Ground Common with Transmitter Ground 40 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Table 9 SFP Pinout Pin Symbol Name Description 15 VccR Receiver Power Supply 16 VecT Transmitter Power Supply 17 VeeT Transmitter Ground Common with Receiver Ground 18 TD Transmitter Non Inverted DATA in AC Coupled 19 TD Transmitter Inverted DATA in AC Coupled 20 VeeT Transmitter Ground Common with Receiver Ground a Circuit ground is internally isolated from chassis ground b Traurr is an open collector drain output which should be pulled up with a 4 7k 10k Ohms resistor on the host board if intended for use Pull up voltage should be between 2 0V to Vcc 0 3V A high output indicates a transmitter fault caused by either the TX bias cur rent or the TX output power exceeding the preset alarm thresholds A low output indicates normal operation In the low state the output is pulled to 0 8V Laser ou
29. emperature monitoring Reset Push button on front panel Front Panel indication LEDs Status LED Red Yellow Green Fans Status LED Red Green UID LED Blue Bad port LED Yellow Green 10 Mellanox Technologies SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 1 2 Serial Number and Product Version Information The serial number and MAC for the switch are found on the back panel The serial number and product version information are found on the label seen in the figure below Near this label is another label with the management MAC Figure 2 Generic Product label f S N MT0924X00266 A 00 X 016X 2BFR MI P N MS Rev X1 TUA IN MAC 0002C902004C ws E AIEO LE Made in Israel x et Rev X41 Figure 3 Management MAC Label Management MAC 0002C902004C Mellanox Technologies 11 Rev 1 2 Installation Safety Warnings 2 Installation Safety Warnings Warnings in French can be found on page 43 Warnings in German can be found on page 46 Warnings in Spanish can be found on page 50 1 Installation Instructions Read all installation instructions before connecting the equipment to the power source 2 Over temperature This equipment should not be operated in an area with an ambient temperature exceed ing the maximum recommended 45 C 113 F Moreover to guarantee proper air flow allow at least 8cm 3 inches of clearance around the ventilation
30. es 174 06W Passive cables 116 18W Power numbers Max Max 10GigE Active Cables 239 53W Passive cables 156 84W SFP Temperature mae power MAX 1 0W Operating 0 to 45 Celsius emperature E TYP 0 8W Non operating 40 to 70 Celsius Shock and Shock and Humidity Vibration _ Vibration ETSI EN 300 019 2 2 1999 09 Operating 5 95 non condensing Humidity Mellanox Technologies 33 Rev 1 2 A 1 A 2 Protocol Support Speed protocol Ethernet Management QoS Auto Negotiation of 10Gb s Managed using MLNX OS Management 1Gb s Data Rate Data Rate 10GigE Regulatory Compliance Safety US Canada cTUVus EMC USA FCC Class A EU IEC60950 Emissions Canada ICES Class A Safety International CB EU EN55022 Class A EMC EU EN55024 Class A Emissions EU EN61000 3 2 Class A EU EN61000 3 3 Class A Japan VCCI Class A Environmental Acoustic EU IEC 60068 2 64 Random ISO 7779 Environmental Vibration ETS 300 753 Acoustic EU IEC 60068 2 29 Shocks Type I II EU IEC 60068 2 32 Fall Test Scalability and Performance Switching Switching Switching Performance Performance Simultaneous wire speed any port Capacity 1 28Tb s Capacity to any port Approved Cables For a list of all approved cables see www mellanox com related docs user manuals Mellanox approved cables pdf EMC Certifications The list of approved certifications per s
31. g upward or downward in the rack When inserting cables into the switch always insert the center row cable before the top and bot tom row cables 4 1 5 Cable Orientation The cables need to be inserted according to Figure 15 Figure 15 Cable Orientation for Insertion 4 1 6 Supported Approved Cables For a list of all approved cables see www mellanox com related docs user manuals Mellanox approved cables pdf 4 2 Disposal According to the WEEE Directive 2002 96 EC all waste electrical and electronic equipment EEE should be collected separately and not disposed of with regular household waste Dispose of this product and all of its parts in a responsible and environmentally friendly way For proper disassembly instructions see the Mellanox website 28 Mellanox Technologies SwitchX 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 5 Management and Tools Overview The switch to be managed either remotely or Out of Band using MLNX OS 5 1 Chassis Management Using the MLNX OS Software The SX10XX switches come standard with a management software module for chassis manage ment called Mellanox Operating System MLNX OS MLNX OS is installed on all SwitchX based managed switch systems MLNX OS includes a CLI WebUI SNMP and chassis manage ment software N A N The Ethernet ports for remote management connect to Ethernet switches These N switches must be configured to 100M 1G au
32. hrough the Switch Slide Before Screwing it to the Switch 5 Screw the switch slides to the switch Mellanox Technologies 37 Rev 1 2 Figure 19 Screw the Switch Slide to the Switch Figure 20 Transfer Power Cord Finished 6 Return to step 4 on page 24 and continue the installation 38 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Appendix D SFP Interface o 11 85 T O oW A 8 50 44 95 56 50 gt 13 60 A Mellanox Technologies de MTSFPP SR Module bod m Ly Mellanox Technologies 39 Top 13 70 8 50 el B ll u a ET 7 lt lt 4 0 4 4 gt 5 S D D D i 2 v F 2 E D D 3 e D o o N o al AR w N N gt al o N 00 c o ED D GD 1 Lond D D DD DD OD 3 d de lt SD x X 6 6 X GB 8 A qb g I a Je gt D e y gt Q E 9 CU e A Table 9 SFP Pinout Pin Symbol Name Description l VeeT Transmitter Ground Common with Receiver Ground 2 TX Fault Transmitter Fault 3 TX Disable Transmitter Disable Laser output disabled on high or open 4 SDA 2 wire Serial Interface Data Line 4 3 SCL 2 wire Serial Interfac
33. installiert ausge tauscht oder gewartet werden 10 Ger teentsorgung Die Entsorgung dieses Ger ts sollte unter Beachtung aller nationalen Gesetze Bestim mungen erfolgen 11 Regionale und nationale elektrische Bestimmungen Dieses Ger t sollte unter Beachtung der regionalen und nationalen elektrischen Bestimmungen installiert werden 12 Richtigen Schutz sicherstellen Geeigneter elekrischer mechanischer und Feuerschutz sind vom Hersteller des Endprodukts oder dem Endbenutzer bereitzustellen 13 Strahlenkontakt Achtung Nutzung von Steuerungen oder Einstellungen oder Ausf hrung von Proze duren die hier nicht spezifiziert sind kann zu gef hrlichem Strahlenkontakt f hren Klasse 1 Laserprodukt und Referenzen zu den aktuellsten Lasterstandards ICE 60 825 1 1993 A1 1997 A2 2001 und EN 60825 1 1994 A1 1996 A2 2001 Mellanox Technologies 47 Rev 1 2 14 UL und CSA Certified Netzkabel F r Nordamerika Stromanschluss w hlen Sie ein Netzkabel das UL und CSA Certi fied LA 3 Leiter 18 AWG mit einem angespritztem Stecker bewertet bei 125 V 15 mit einer Mindestl nge von 1 5 m Six Feet aber nicht mehr als 4 5 m F r die europ ischen Zusammenhang w hlen Sie ein Netzkabel das international harmonisiert und der Aufschrift lt HAR gt 3 Leiter mindestens 0 75 mm2 Draht bewertet mit 300 V mit einem PVC Mantel isoliert Das Kabel muss eine angespritztem Stecker bewertet bei
34. openings 3 Stacking the Chassis The chassis should not be stacked on any other equipment If the chassis falls it can cause bodily injury and equipment damage gt 4 Double pole Neutral Fusing This system has double pole neutral fusing Remove all power cords before opening the cover of this product or touching any internal parts gt 5 During Lightning Electrical Hazard During periods of lightning activity do not work on the equipment or connect or dis connect cables gt 6 Copper Cable Connecting Disconnecting Copper cables are heavy and not flexible as such they should be carefully attached to or detached from the connectors Refer to the cable manufacturer for special warnings instructions gt 12 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 7 Rack Mounting and Servicing to ensure that the system remains stable In general you should fill the rack with equip When this product is mounted or serviced in a rack special precautions must be taken A ment starting from the bottom to the top 8 High Leakage Current WARNING High leakage current Earth connection essential before connecting sup LA ply 9 Connect a Valid Ground to this Device Before connecting this device to the power line the protective earth terminal screws of this device must be connected to the protective earth in the building installation 10 Equipment
35. orriente al equipo provee una conexi n con la puesta a tierra de protecci n del edificio De no ser as el T CNICO DE SERVICIO se encargar de instalar un CON DUCTOR DE CONEXI N A TIERRA DE PROTECCI N del terminal de puesta a tierra de protecci n separado al conductor de tierra de protecci n del edificio El equipo se instalar en un rea donde haya conexi n equipotencial como por ejemplo un centro de telecomunicaciones o una sala de computadoras dedicada 16 C digos de instalaci n Este dispositivo se debe instalar conforme a la versi n m s reciente de los c digos el ctricos nacionales del pa s en cuesti n En Am rica del Norte el equipo se debe instalar de acuerdo con las disposiciones vigentes del C digo El ctrico Nacional de los EE UU y del C digo El ctrico de Canad 17 Directiva sobre RAEE Conforme a la Directiva 2002 96 CE sobre RAEE todos los residuos de equipos el c tricos y electr nicos EEE se deben recolectar por separado y no se deben eliminar junto con residuos dom sticos Al deshacerse de este producto y de todas sus partes h galo de una manera respon a sable y respetuosa con el medio ambiente 52 Mellanox Technologies SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Appendix Special Regulations Regarding Finland Swe den Denmark and Norway Denmark This unit is class I and must be connected with an AC cord compliant with all national electri
36. r connections The power cords should be standard 3 wire AC power cords includ ing a safety ground and rated for 15A or higher 26 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Caution The power supplies in this switch are Double Pole Neutral Fusing Caution The switch platform will automatically power on when AC power is applied There is no power switch Check all boards power supplies and fan tray modules for proper insertion before plugging in a power cable N Caution After inserting a power cable and confirming the green system status LED B light is on make sure that the Fan Status indicator shows green If the fan status indicator is not green then unplug the power connection and check that the fan module is inserted properly and that the mating connector of the fan unit is free of any dirt and or obstacles Caution When turning off the switch make sure ALL Connector LEDS are off to ensure a powered down status 4 1 3 Grounding the Switch Check to determine if your local or national electrical codes require an external ground to all IT components If so connect a ground wire to one of the casing screws and connect the other end to a valid ground If you choose to not use the ground screw make sure that the rack is properly grounded and that there is a valid ground connection between the chassis of the switch and the rack Test the ground using an Ohm meter
37. riana eri hie Dean bu uisa 28 4 1 6 Supported Approved Cables 28 4 2 Disposal osi edit ERIT POETS A RM MO CORSA ER ERA Ow 28 Chapter 5 Management and Tools Overview 29 5 1 Chassis Management Using the MLNX OS Software 29 5 2 Configuring the Switch for the First Time 29 5 2 1 Starting a Remote Connection to the Switch 29 5 2 2 Upgrading Software 30 Mellanox Technologies 3 Rev 1 2 Chapter 6 Troubleshooting 31 Appendix A Specification 33 Ad JApproved GablBS lt a csse ee pesas grado us 35 A 2 EMC Certifications re SAA QU ARS 35 A 3 China CCC Warning Statement 36 Appendix B Thermal Threshold Definitions 37 Appendix C Transferring the Power Cord 38 Appendix D SFP Interface 40 Appendix E Replacement Parts Ordering Numbers 43 Appendix F Avertissements de s curit d installation French 44 Appendix G Installation Sicherheitshinweise German 47 Appendix H Advertencias de seguridad para la instalaci n Spanish 51 Appendix I Special Regulations Regarding Finland Sweden Denmark and Norway 54 4 Mellano
38. sage will be issued by the MLNX OS management SW indicating to system administration that the switch has crossed the Warning threshold Note that this temperature threshold does not require nor lead to any action by hardware such as switch shutdown 2 Critical 120C When the SwitchX device crosses this temperature the firmware will automatically shut down the device 3 Emergency 130C In case the firmware fails to shut down the SwitchX device upon crossing the Critical thresh old the SwitchX device will auto shutdown upon crossing the Emergency 130C threshold 36 Mellanox Technologies J SwitchX 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 Appendix C Transferring the Power Cord To use the rail kit to transfer the power cord from the connector side to the power side follow these directions Do you want to install power cords on both sides of the switch or only one side For each power cord you want to transfer Once you have decided which side of the switch will be next to the vertical support 2 Make sure that you place the cord so that the correct end of the cord will be at the power side of the switch This will depend on which of the four mounting options you choose Figure 17 Transfer Power Cord 3 Put the power cord in the switch slide channel 4 Push the cord end through the hole in the switch slide Leave 7 of cord hanging out from the hole Figure 18 Put the Cord T
39. the next symbol error is received 3 1 1 5 UID LED Switch Identifier The UID LED is a debug feature that will become available to customers in the near future For details please contact Mellanox Technologies support 3 1 1 6 Port Connector LED The port LEDs are assigned to the ports as in figure Mellanox Technologies 17 Rev 1 2 Hardware Basic Operation and Installation 3 1 2 Port Connector LED Assignment Figure 6 LED to Port Assignment EN YE m E Em Between the top two ports is a row of LEDs The left LED is for the top port in the column the middle LED is for the center port in the column and the right LED is for the bottom port in the column Some versions of this switch have a fourth LED When there are four LEDs the second from the left will be disabled Table 6 Port Connector Physical and Logical Link Indications LED Configuration LED Description Off Physical link down Default Solid Green Physical link up no traffic Flashing Green Physical link up with traffic Flashing Orange Physical errors This LED when flashing orange shows port physical errors Possible causes for this are bad cable bad connection bad connector bad cage 3 2 Air Flow These switches can come with two air flow patterns The two patterns are power supply side inlet to connector side outlet connector side inlet to power supply side outlet The
40. tions in the Installation Guide Configuring the Switch for the First Time For the Socket pinout see RJ45 CONSOLE and Ethernet Interfaces on page 51 3 5 2 Mini USB This interface can be used to update SW 3 5 3 RJ 45 Ethernet Connector The Ethernet connection labelled provides access for remote management The switch can be connected to any Ethernet port Mellanox Technologies 19 Rev 1 2 Hardware Basic Operation and Installation Warning Any red status LED is cause for concern and must be dealt with immediately It can take up to 4 minutes to boot up during which time the status LED may indicate red 3 5 4 12C Connector There is an I2C interface on the side panel This interface is only for FAEs and advanced users 20 Mellanox Technologies J SwitchX 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 4 Installation 4 1 Package Contents and Installation Before you install your new switch unpack the system and check to make sure that all the parts have been sent check this against the parts list below Check the parts for visible damage that may have occurred during shipping The switch comes packed with the following items e X switch 1 X installation kit e X power cable for each PSU Type B 6ft US 125V 10A cord e See Replacement Parts Ordering Numbers on page 42 to order power cords for various coun tries Asingle power cord for each power supply unit can be or
41. to Weight u oe LL 40 lbs 40 70 lbs 70 121 lbs gt 121 lbs lt 18 kgs 18 32 kgs 82 55 kgs gt 55 kgs Use enough people to safely lift this product A lt 40 lbs 40 70 Ibs 70 121 Ibs gt 121 Ibs lt 18 kgs 18 32 kgs 32 55 kgs gt 55 kgs Mellanox Technologies 49 J Rev 1 2 Appendix H Advertencias de seguridad para la insta laci n Spanish 1 Instrucciones de instalaci n Wy Antes de conectar el equipo a la fuente de alimentaci n leer todas las instrucciones de 4 instalaci n A 2 Lesi n corporal por peso LA e 40 lbs 40 70 lbs 70 121 lbs gt 121 lbs lt 18 kgs 18 32 kgs 32 55 kgs gt 55 kgs 3 Lesi n corporal por peso This equipment is very heavy and should be moved using a mechanical lift to avoid injuries 4 Sobrecalentamiento No se debe utilizar el equipo en un rea con una temperatura ambiente superior a la m xima recomendada 45 C Adem s para garantizar una circulaci n de aire adec uada se debe dejar como m nimo un espacio de 8 cm 3 pulgadas alrededor de las aberturas de ventilaci n 5 Apilamiento del chasis Los chasis no se deben apilar sobre otros equipos La ca da del chasis podr a causar lesiones corporales as como da os al equipo 6 Dos fusibles uno en el polo y otro en el neutro Dos fusibles uno en el polo y otro en el neutro Quitar los cables de corriente antes de abrir la tapa de
42. to negotiation 5 2 Configuring the Switch for the First Time See the Installation Guide of the switches Configuring the Switch for the First Time The port labelled must be connected to a local host PC This must be used the first time the switch is connected This must be done before any remote management is available Hook up the supplied harness cable HARO00028 from the connector labelled to the DB connector of the local host PC Figure 16 Host Connection Manage CONSOLE 5 2 1 Starting a Remote Connection to the Switch For details on the SNMP commands and MIBs supported refer the MLNX OS Soft ware Command Reference Guide Mellanox Technologies 29 Rev 1 2 Management and Tools Overview 5 2 2 Upgrading Software The new software and firmware update is available from the Mellanox Support website Copy the update to a known location on a Remote server within the user s LAN Use the CLI or the GUI in order to perform Software upgrade For further information please refer to the MLNX OS user manual Be sure to read and follow all of the instructions regarding the updating of the software on your switch system 30 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 6 Troubleshooting As soon as a switch is plugged in continuously monitor the status light Make sure that it turns green within 4 minutes of
43. tput disabled on TDIS gt 2 0V or open enabled on TDIS 0 8V d Should be pulled up with 4 7kQ 10kQ on host board to a voltage between 2 0V and 3 6V MOD ABS pulls line low to indicate module is plugged in e LOS is open collector output Should be pulled up with 4 7kQ 10kO on host board to a voltage between 2 0V and 3 6V Logic 0 indicates normal operation logic 1 indicates loss of signal e Mellanox Technologies 41 J Rev 1 2 Appendix E Replacement Parts Ordering Numbers Table 10 Replacement Parts Ordering Numbers Part Description OPN RS232 Cable RJ45 to DB9 Harness HAR000028 I2C DB9 or RJ45 to USB Adapter MTUSB 1 Power cord Type C13 C14 ACC000251 250V 10A 1 5M Power cord Type C13 C14 ACC000242 250V 15A 2M RIGHT ANGLE Power cord Type B for USA Canada Mexico Taiwan Type B 6ft US 125V ACC000204 10A cord Power cord Type B for USA Canada Mexico Taiwan ACC000241 125V15A 4M USA UL Type B RIGHT ANGLE Power cord Type H for Israel ACC000205 Power cord Type E F for Sweden France Germany Netherlands Russia ACC000207 Power cord Type G for UK ACC000208 Power cord Type D for India ACC000209 Power cord Type I for China ACC000210 Power cord Type J for Switzerland ACC000211 Power cord Type B for Japan ACC000212 Power cord Type I for Australia ACC000213 42 Mellanox Technologies J SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual
44. witch in different regions of the world is located on the Mellanox website at www mellanox com related docs user manuals Regulatory and Compliance Guide pdf EMC statements are also in the Regulatory and Compliance Guide 34 Mellanox Technologies J SwitchX 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 A 3 China CCC Warning Statement AN China CCC Warning statements 1E IE RORTE EENAA English translation disconnect all power sources before service For non tropical use XX RAR TREE Dan hab yungh youq gij dienheig diuzgen mbouj dwg equ haenx ancienz saw h MERFER200NN HRA 200 0m rent WC n Ont eed GO m Orr c9 M oo 5 tt Au Dan hab yungh youq gij digih haijbaz 2000m mS haenx ancienz saw h gados SALES a Yos ig 0999 ph 2000 an gt Warning for Class A E Ich A SPR CERTAN VERTRAT ERS TI t MENT TARRO English translation of above statement This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Mellanox Technologies 35 Rev 1 2 Appendix B Thermal Threshold Definitions There are three thermal threshold definitions for the SwitchX switch device which impact the overall switch system operation state Warning Critical and Emergency 1 Warning 100C On managed systems only When the SwitchX device crosses the 100C threshold a Warning Threshold mes
45. x Technologies SwitchX amp 64 Port SFP Ethernet Switch Hardware User Manual Rev 1 2 List of Figures Figure 1 SX1016 Swilch ies el aa RR RR eR E Mau bales ESAME RT Ea RS 10 Figure 2 Generic Product label sos 22 20 304 e eR ea Oak an 11 Figure 3 Management MAC Label 11 Figure 4 Switch System Front Panel 15 FIgur 5 Status LEDS oos cease tx box EX PE RE ELE a E 15 Figure 6 LED to Port ASSIQnINGht soe oe yu e 8S WES ee ann 18 Figure 7 Port Numbering 2254 ott atu ust tuned ua eot CASE aud Mt eee sure 19 Figure 8 Management Interfaces 19 Figure 9 Rack Rail Kit Parts ras tn Eb due goi it sx a ine 22 Figure 10 Placement of Switch in Rack 23 Figure 11 Mounting Options ioni RIED CSI a ee 24 Figure 12 Screwing on the Hall dee ans carta Sed Meanie es eich Reais eae See 25 Figure 13 Inserting the Caged Nuts 2 42 22 22 80 Rr a a a UI 25 Figure 14 Slide the Rail into the Rail Slide 26 Figure 15 Cable Orientation for Insertion 28 Figure 16 Host Connection sauce he 4045089 ENSURE sales S eto XE fees 29 Figure 17 Transfer Power Cord u 2225 d EE a RR REG AAA TR UR 38 Figure 18 Put the Cord Through the Switch Slide Before Screwing it to the Switch 38 Figure 19
Download Pdf Manuals
Related Search