USER`S MANUAL - Pdfstream.manualsonline.com
Contents
1. STANDINIR DE USER S MANUAL EV Rider LLC CENY Rosem 6410Arc Way SuiteA Fort Myers FL 33966 FB www evrider com 1 800 944 1997 IMPORTANT SAFETY NOTICE It is important to read and follow all the instructions and safety information contained in this Owner s Manual prior to use Always wear a safety helmet which is provided with each SNR scooter Do not operate at night Comply with all local laws and regulations Do not use in wet conditions Do not use off road This device is designed for hard surfaces only Recommended for riders 16 years of age or older Check all take apart locks before each use Ensure battery pack is properly charged before use Using the half speed mode practice in a large open area free of vehicles obstacles and pedestrians Do not use the full soeed mode when using the scooter with the optional seat Send your warranty registration card as soon as possible PAGE Important Safety Information 0 c ccececececuceceveees 3 General Information 0 0 0 0 0 ccc c eee c eee e eevee ee eees 3 2781 Teranse as redene a E A wea 3 Mechanical Systems des 4 About the Batteries et nae hacen cee araara 4 Additional Safety Information 4 4 4 4 5 Stand N Ride Overview Diagram 6 Assembly Instructions ahs Yr epee Sea2. battery charge may be low Charge the batteries until full charge is shown N One of both of the batteries may be bad Have the batteries tested with a load tester to determine if they hold charge The batteries are probably low An over load current was detected by the controller The scooter drives but suddenly stops during riding N Ww Overheat condition detected by the controller SPECI FI CATIONS Page 13 Model number SNR 1000 Color Black Textured ABS Plastic amp Metallic Silver Frame Overall length 992 mm 36 3 in Overall width 642 mm 25 3 in Ground clearance 75 3 in Weight capacity 136kg 300 Ib Component Weights Base With optional flat free tires 19 8 kg 43 5 Ib Tiller 18 42 kg 40 5 Ib Battery Pack 12 59 kg 27 7 b Seat amp Charger 5 85 kg 11 Ib Total 56 66 kg 122 7 Ib Top speed 24 km h 15 mph Motor type Brushless DC hub motor 24V 500W Tire size 12 5 X 2 25 Pneumatic Optional flat free Battery type 12V 18 AH Charger 2A Off Board Optional Seat type Oversized bicycle base with built in backrest Important Notice Dimensions and specifications are subject to change without prior notice Page 14 WARRANTY TERMS ONE YEAR LI MI TED WARRANTY One year on all structural frame components including tiller base frame and seat post if
3. battery gauge is in the green zone 5 Make sure that the speed direction switch FWD REV is set to go forward or reverse depending on the direction that you want to go to 6 Select the speed setting Fast or Half Speed as desired We recommend that you begin using the Stand N Ride scooter only in half speed until you get acquainted with Page 11 the unit and become proficient riding it 7 Gradually apply the throttle until the desired speed is achieved Once again we recommend that you do not venture to full soeed operation until you have become proficient with the scooter and only if you are certain that there are no obstacles in site on an open field 8 Make sure to slow down your speed while turning and balance your weight to the opposite side of the turns to ensure the unit s stability IMPORTANT NOTICE The Stand N Ride s microcomputer controller automatically cuts off power to the motor whenever the brake is applied the motor regains power after a short pause after releasing of the brake Likewise if the brake is set to the lock position drive is disabled Make sure to release the brake before you apply the throttle If you are using the seat option we strongly recommend that you do not use the FAST speed setting Battery system and Charger Warning Only use the battery charging unit that was supplied with your Stand N Ride scooter Use of any other battery charging unit or equipment voids your warranty and may
4. ct the ability to stop the unit Page 4 Mechanical Systems Check all joints hinges and quick releases to ensure that the Stand N Ride is properly assembled Stop using the product immediately if any joint hinge or quick release becomes loose Re tighten the joint hinge or quick release prior to resuming the ride The electric motor batteries and controls can get damaged if exposed to water Do not use the Stand N Ride in the rain and do not drive through water puddles If the brake lever touches the handle bar grip stop using the unit until the brake lever is adjusted or replaced About the Batteries The batteries two 18 Ah batteries are contained in the battery box which also houses a circuit breaker and the charger port While the batteries are charged before shipping from the manufacturer we recommend that you charge the batteries fully before the first use at least 4 hours Use caution when recharging the batteries Do not charge the batteries in an area prone to becoming wet Recharge the batteries only in an area that is well ventilated Keep children away from the Stand N Ride while it is being recharged Do not use an extension cord to plug the charger to the wall outlet Stop using the charger if the power cord or the charger connector XLR connector becomes worn broken or damaged in any way Have the product inspected and repaired by an authorized qualified dealer Do not modify the electrical control
5. d Toe 7 Tiller Assembly praadecgstl 4 7 Base Frame Assembly osasacves ctevpesgnhidey 7 Installing the Optional Seat Assembly 5 5555 8 Coupling the Tiller to the Base Frame 55555555555 9 Installing the Battery Pack scciiw ts aves down econ dae dy es 9 Before You Ride Checklist 2 0 c cece eee e runnner rran 10 How to Ride the ed oh onde wad 8 ces 10 Battery System and Charger 5 6 2 datas 3 7 on tate a tes o 11 Basic MaintenanCe scone kep Se oY eee ee eg GN wae ees 12 Trouble Shooting Shute 25 2 12 Specifications ask MOR Bde cnet pa See UNS ek E 13 14 Warranty Information TABLE OF CONTENTS Page 3 IMPORTANT SAFETY I NFORMATION It is important to read and follow the instructions and the safety information contained within this owner s manual prior to use General I nformation The SNR is a recreational battery operated vehicle It is not a mobility device for medically prescribed use and should not be used as such Always wear a helmet when riding the SNR For your convenience and safety EV Rider provides a helmet with each SNR scooter This product is not recommended for users you
6. k from the main base component to ease the task of installing the wheels Slide a washer on the rear wheel shaft Fig 3 Now install the wheel followed by the other washer and the Nylock nut Tighten it by hand Repeat the process on the other side for the remaining wheel Using a 22 mm wrench or a 7 8 wrench tighten the nut to secure the wheels in place DO NOT over tighten the nut and make sure that the wheel turns freely but is securely fastened to the shaft Fig 4 Repeat the process for the other side Page 8 Installing the Optional Seat Assembly Locate all the seat assembly components and have them at hand to begin the installation of the seat assembly Fig 5 Remove the seat post locking collar from the main seat post tube to allow insertion of the tube through the base frame from the bottom up fig 6 Flip the base over to the side and insert the main seat post tube Make sure that the adjustment holes face the left wheel otherwise you may end up with the basket brackets facing the front of the scooter which is not appropriate Fig 7 Fasten the 4 Allen bolts to the base frame and tighten them very well using the Allen key provided Make sure that you do not forget to slide a pressure nut into every bolt before affixing it to the base frame Flip the base frame over and re install the locking seat post locking collar Do not tighten yet This will have to be done after you have in
7. nger than 16 years old Operators must comply with local laws and regulations Check with your local Police Department or the Dept of Motor Vehicles to determine your local requirements with respect to the SNR SNR scooters require skill to operate safely Practice starting stopping and turning ina large open area free of vehicles obstacles and pedestrians Do not operate the SNR at night The SNR is not equipped to be operated outdoors at night or in low light conditions It may not be visible to other vehicles or pedestrians in these conditions Do not operate the vehicle near children When approaching pedestrians announce your presence to minimize sudden unexpected moves by pedestrians This product is designed to be used only by one rider Do not carry any additional people Do not carry any items on the SNR unless they securely placed in the basket Do not tow or pull the SNR electric scooter behind a vehicle bicycle or pedestrian Do not use the SNR to tow or pull anything Riding Terrain Ride only on smooth hard flat surfaces The SNR is not intended for off road or hilly terrain conditions Use caution when approaching curbs uneven pavement potholes or similar conditions The wheels are not intended to go over more than 3 obstacles You may fall when running over these obstacles Do not ride the Stand N Ride downhill for extended periods of time This may increase the wear of the brake lining and adversely affe
8. ourself Service by anyone other than an authorized service center will void the product s warranty For service information call 1 800 944 1997 or visit our website at www evrider com Page 6 Stand N Ride Overview Fast Slow Battery Gauge ON OFF Headlight FWD REV Brake gt Horn Throttle Optional Seat Basket Take Apart ii N Rear Wheel Hub Motor Drive Wheel Battery Pack Anti Tippers Page 7 Assembly Instructions Your Stand N Ride is shipped in two boxes 1 containing the tiller and 1 containing the base frame After you have removed the Stand N Ride components from the protective packaging you are ready to set up your scooter for riding by following these steps Tiller Assembly Loosen the tiller height lock to allow for the insertion of the upper portion of the tiller handle bar Fig 1 and Fig 2 Making sure that the main wire harness and the brake cable are not caught by the tubing insert the upper tiller section and slide it to your desired height Fasten the center guide screw so the tiller stays centered and then lock it in place by tightening the collar lock with the Allen key provided You can always loosen it and re adjust the height if your initial height is not comfortable Make sure that the tiller is centered and securely fastened before you move to the next step Base Frame Assembly Remove the battery pac
9. purchased with this option From one 1 year from the date of purchase if any part or electronic component of the Scooter is found upon examination to be defective in material and or workmanship it will be repaired or replaced at EV Rider s option without charge Labor charges are not provided under warranty The purchaser is responsible for the delivery to the authorized repair facility Satisfactory proof of purchase serial number and the date of purchase are always required For warranty service please contact the retail establishment from whom you purchased your EV Rider product ONE YEAR WARRANTY EXCEPTIONS Motor In cases where there is an increase in the operational noise level the warranty does not apply The increase in operational noise level usually occurs due to abusive and excessive strain on the scooter The battery is warranted by EV Rider for 6 months after the purchase of the product Warranty service can be performed by EV Rider or by an authorized EV Rider service facility Do not return faulty parts to EV Rider without prior consent All transportation costs and shipping damage incurred while submitting parts for repair or replacement are the responsibility of the original purchaser WARRANTY EXCLUSIONS This warranty is only given to the original purchaser of the Scooter The Warranty excludes Consumable items which may need replacing due to normal wear and tear tires tubes belts bulbs upholste
10. result in severe damage to the battery pack and the scooter and may cause a fire hazard Always wait until the battery gauge shows at least half charge to recharge the batteries Overcharging may result in decreased battery life The battery pack can be recharged either while in the Stand N Ride or when removed To charge the battery pack 1 Remove the battery charger port cover Fig 15 2 Plug the XLR connector to the charger port Fig 16 3 Plug the charger plug to the wall outlet When charging the charger s LED should show any of the following colors RED shows that the charger is plugged to the wall but not to the unit AMBER shows that the charger is charging the batteries GREEN shows that the charger has finished charging the batteries or that the batteries are full and do not need charging Page 12 Basic Maintenance The Stand N Ride has been designed to provide years of trouble free riding enjoyment provided that the user takes care of it by not leaving it exposed to the elements neglecting to charge it or by using it in any way that is not recommended Due to the Stand N Ride s modular design there are virtually no user serviceable parts Attempting to service or modify any of the scooter s internal components may result in permanent damage to the scooter and will void the warranty For service and repair contact your nearest EV Rider dealer It is always best to check before each ride the condition of
11. ry and seating motor brushes fuses plastic shrouds and footrest covers etc Damaged caused by battery fluid spillage or leakage abuse misuse accident or negligence improper operation excessive loading maintenance or storage commercial use or use other than normal Used other than for the purpose of the purchaser s mobility Repairs and or modifications made to any part of the scooter without specific and prior consent from EV Rider LLC Labor service calls shipping and other charges incurred for repair of the product not expressly approved by EV Rider Batteries Batteries carry a limited warranty which is subject to a stringent wear and tear clause Any battery faults due to a defect in the original manufacture will normally become obvious within the first two months of use Any gradual deterioration in performance after this period is normally associated with fair wear and tear misuse or accidental damage and as such is not covered by the manufacturer s warranty There is no other express warranty Implied warranties including those of merchantability and fitness for a particular purpose are limited to one 1 year from the date of the original purchase and to the extent permitted by law Any and all implied warranties are excluded This is the exclusive remedy Liabilities for consequential damages under any and all warranties are excluded Page 15 NOTES
12. s or wiring Any attempt to do this may result in injury and will void the warranty immediately Use only motors batteries and charging units supplied or approved for the Stand N Ride scooter Do not use the Stand N Ride batteries to power any other battery operated equipment Page 5 Additional Safety 1 nformation Adjust the handle bar height to provide a comfortable and secure riding position on the Stand N Ride scooter The rider s hands should be able to easily grasp the handle bar controls throttle and brake lever They should not be higher than the waist or lower to ensure proper posture and riding control of the unit If using the seat option the handle bar should be lower to compensate for the seating height of the user The seat height should be such that both feet should rest on the floorboard comfortably and the hands must be able to grasp the handle bar controls Handle bar and seat height positions should be locked and tightened When finished riding the Stand N Ride scooter remove the key and take it with you This prevents unauthorized use of the product especially by children After taking the product apart for transportation be certain to protect the handle bar controls from accidental damage and make sure that you balance the components particularly on stairs to avoid falls If service is necessary contact your authorized Stand N Ride electric scooter service Do not attempt to service the electric scooter y
13. serted the seat assembly and once you select your desired seat height Making sure that the basket brackets face towards the rear of the seat backrest insert the adjustable removable seat post tube into the seat base receiver Tighten the nut and bolt Fig 8 Insert the seat assembly onto the receiver seat post Fig 9 and select your desired seat height DO NOT forget to lock the seat post collar Fig 10 now You are now ready to couple the tiller and the base frame together Page 9 Coupling the Tiller to the Base Frame Remove the secondary safety knob from the tiller coupler pin to allow the pin to slide through the base frame receiver Align the tiller coupler pin with the base receiver tube and slide it over the tiller pin Fig 11 Wiggle it lightly until the locking spring locks in place The wire connector would have locked itself in place at the same time Make sure that the connection is secure by deflecting the spring lock and verifying that it rests on the groove of the tiller pin Fig 12 This is an indication that the connection is secured Attach the secondary safety knob and tighten it Fig 13 Installing the Battery Pack With the battery connector at the bottom of the of the battery box facing forward towards the front wheel slide the battery pack onto the battery housing Fig 14 until the top of the battery pack lines itself up with the floorboard Turn the igni
14. the cables brakes and folding latches to ensure their proper settings and tightness Occasionally lubricate exposed latches cables and fittings to keep proper function Trouble Shooting Below are tips on how to handle technical situations that you may encounter PROBLEM PROBABLE CAUSE S The key is turned to the ON position but 1 The battery pack may not be fully engaged Check that the floorboard and the top there is no drive of the battery pack are at level with each other 2 The battery charge may be too low to drive and may need charging The key is turned to the ON position the You probably have the charger plugged to the unit or to the unit and the wall The batteries are fully charged and the brake controller disables drive if it detects the charger connected to the unit lever is not locked m The key is turned to the ON position the The brake may be engaged which disables the controller Depress and unlock the battery gauge shows charge but there is brake no drive The tiller base frame coupler doesn t lock The power connector is probably not aligned to allow for the tube to slide over the in place pin completely Make sure that this is aligned and fully connected The unit takes too long to brake and The brake needs adjusting Rotate the brake cable adjuster away from the brake doesn t brake completely lever m The unit drives but stops after a while The
15. tion key to the ON position and tap the f horn button to verify the connection You are now ready to test your Stand N Ride Page 10 Before You Ride Checklist Before riding the Stand N Ride electric scooter be sure to carefully follow the checklist below Read and understand the Important Safety information section of your Owner s Manual Make sure that the battery pack has been fully charged Check that the battery pack connection to the base frame is tight Check that the tiller and the base unit components are securely connected and that the secondary safety knob is in place and securely fastened Make sure that the handle bars height and the seat height if you are using this option are adjusted to your preference Carefully check all joints quick release levers locking buttons and latches to ensure each is secured Check that your tires are properly inflated if not fitted with the flat free option Check the brake lever for proper function Most importantly make sure to have your helmet ready to be worn How to ride the Stand N Ride Scooter It is important that you understand how to operate the scooter so carefully follow these steps 1 Mount the unit and position yourself behind the handle bars with your feet resting on the floorboard 2 Check that the brake is not locked Squeeze it to disengage it if it were locked 3 Turn the key to ON position clockwise 4 Check to see if the
Download Pdf Manuals
Related Search