Home

User Guide - GarrettCom

1. Make sure that an AC power cord is properly attached to each Magnum 6K25 Switch unit Be certain that each AC power cord is plugged into a functioning electrical outlet Use the PWR LEDs to verify each unit is receiving power If the problem is isolated to a network device other than the Magnum 6K25 Switch product it is recommended that the problem device be replaced with a known good device Verify whether or not the problem is corrected If not go to Step 5 below If the problem is corrected the Magnum 6K25 Switch and its associated cables are functioning properly If the problem continues after completing Step 4 above contact your supplier of the Magnum 6K25 Switch unit or if unknown contact GarrettCom Inc by fax phone or email support garrettcom com for assistance When Calling for Assistance Please be prepared to provide the following information A complete description of the problem including the following points a The nature and duration of the problem b Situations when the problem occurs c The components involved in the problem d Any particular application that when used appears to create the problem An accurate list of GarrettCom product model s involved with serial number s Include the date s that you purchased the products from your supplier www GarrettCom com E 53 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 J It is useful to include other networ
2. This warranty will not be effective if in the opinion of GarrettCom the product has been damaged by misuse misapplication or as a result of service or modification other than by GarrettCom GarrettCom reserves the right to make a charge for handling and inspecting any product returned for warranty repair which turns out not to be faulty Please complete the warranty card as this acts as a product registration and mail it to GarrettCom within two weeks of your purchase APPENDIX B Internal DC Power Supply Options B1 0 SPECIFICATIONS FOR MAGNUM 6K25 SWITCHES DC POWER Power Supply Internal 48VDC Option DC Power Connector 3 terminals GND Input Voltage 36 70 VDC Power Consumption Same as for AC models see Section 1 1 Power Supply Internal 24 VDC Option Industrial Applications DC Power Connector 3 terminals GND Input Voltage 20 36 VDC Power Consumption Same as for AC models see Section 1 1 Power Supply Internal 125 VDC Option Industrial Applications DC Power Connector 3 terminals GND 55 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Input Voltage 88 150 VDC Power Consumption Same as for AC models see Section 1 1 With the exception of the power supply all specifications and functions of Magnum 6K25 Switch 48VDC 24VDC and 125VDC models are identical to those listed in the main manual B2 0 48VDC
3. mode ST type connectors and 6KP6 RJMST dual speed copper ports The 4 Port 10 100Mbps and 2 100 Mb ST Fiber Port ST connector functions as a fiber optic transceiver to support OOBASE FX network segments When installed in a Magnum 6K25 Managed Switch the copper port supports the standard distance 100m on each port and the fiber 2 baa 2 imac port supports fiber optic cable distances up the IEEE standard 100Mbps distance limits 1 e typically 2km at full duplex and 412m at half duplex Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and FDX HDX LED to indicate full duplex mode when lit or half duplex when off The www GarrettCom com E 41 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 10 100 LED indicates the speed if the LED is ON 100Mbps if it is OFF 10Mbps 5 2 la 6KP6 RJ10ST 4 10 100Mbps RJ 45 and 2 10Mb multi mode FX ST twist lock Combo Module The 6KP6 RJIOST is a six port combo module that looks similar to the 100Mb combo module with the exception of 10Mb speed at the ST fiber module The ST connector functions as a fiber optic transceiver to support L OBASE FX network segments When installed in a Magnum 6K25 Managed Switch the copper port supports the standard distance 100m on each port and the fiber port supports fiber optic cable distances up the IEEE standard 10Mbps d
4. 4 10 100Mb transceivers are compatible with the IEEE 802 3z Gigabit standards There are two LEDs mounted on each Gigabit port module The Gigabit fiber port is by default configured at AUTO mode and can be fix at 1000Mbps speed full duplex mode at any times and has LEDs that indicate LK Link status and ACT receiving activity on that port when lit 2 2 9 Packet Prioritization 802 1p QOS Quality of Service means providing consistent predictable data delivery to users from datagram paths that go all across a network As a LAN device the Magnum 6K25 can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and buffers The Magnum 6K25 switching hardware supports the IEEE 802 1p standard and fulfills its role in support of QOS giving packet processing priority to priority tagged packets according to the 802 1p standard In addition to hardware support for QOS the MNS software R2 supports two priority queues that can be shared across the eight levels of defined packet priorities for application specific priority control by the user through software configuration settings 2 2 10 Frame Buffering and Flow Control Magnum 6K25 s are store and forward switches Each frame or packet is loaded into the Switch s memory and inspected before forwarding can occur This technique ensures that all forwarded frames are of a valid length and have the correct CRC 1 e are good packets Th
5. Combo 4 100Mbps multi mode LC small form factor and 4 10 100 Mbps RJ 45 Connector The Magnum 6KP8 45LC Module is a combo module with a combination of copper and Fiber Small Form 4 Port 10 100Mbps amp 4 port 100Mbps Factor LC type ports The Multi Mod LC OM small size of LC connectors give an advantage of having more ports on one module The 6KP8 45LC is equipped with 4 10 100 RJ 45 ports and 4 LC F AC A AC ra LKE NO Small form factor multi mode C1 LINK 2 10 10 fiber ports When installed in a Magnum 3 errr Q FULL HALF 6K25 Switch it supports the 47 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 standard distances as per mentioned on 5 2 8 and the LEDs also acts similarly as mentioned above 5 2 9 6KP8 RJ45 Twisted Pair 10 100Mb 8 Port The 6KP8 RJ45 PAA module supports Ethernet 8 Port 10 100Mb Copper ports twisted pair segments of any standard length It is equipped with an eight port RJ 45 connector and offers 10 100 full half duplex auto negotiating capability on each port The RJ 45 connector is shielded to minimize emissions 3 ACTIVITY 4 FULL HALF and will allow both unshielded twisted pair UTP and shielded twisted pair STP cable connections The 6KP8 RJ45 module is equipped with a Media Dependent Auto Crossover MDI X switch which controls all ports for cascaded connection This feature eliminates the need for a
6. Fig 3 5 2h Inside view of chassis cover from the rear showing the front panel screen plates installed inside the chassis cover using brackets and screws Step 8 Once all 6KPM cards have been installed including faceplates for empty slots the chassis cover should be replaced Make sure the chassis cover is aligned properly before securing the enclosure 32 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 NOTE Gigabit Module only The Gigabit port module installation on slot A B and C COTX require four bracket extender for each slot A B or C COTX Attach the bracket from the PCA to the center standoff on the main mother board The bracket provide the stability to the Gigabit module NOTE Reverse mount Model The Reverse model require a LED Decal for checking the speed F H and activity status 3 5 3 Removing 6KPM Cards To properly remove a 6KPM card from the 6K25 Managed Fiber Switch follow the 3 steps below Step 1 Remove chassis cover See procedures in Section 3 5 1 above Caution Be sure the power cord is unplugged Step 2 Remove retaining screws placed on top for the 6KPM and Face Plate On the top of the daughter module there are six retaining screws for each 6KPM card These screws are used to secure a 6KPM card in position see Figure 3 5 3a Remove the three standoffs holding the Granddaughter board with the chassis The screen faceplate screws out from the inside front of th
7. notice that there are individual PM installation spaces and female latch white connectors provided on the main board along with four stand off s for each 6KPM card position See Figure 3 5 1b mes sirg Figure 3 5 1b Magnum 6k25 Top view without chassis cover Step 3 Remove front panel face plate retaining screws There are four PM slots A B C and D located on the front of the chassis cover Looking into the vertical placed Chassis cover of the unit there are three brackets with retaining screws 256 flat head which hold each PM Face plate card slot securely These six screws shown in the picture below are used to secure a PM face plate in position but unscrew only four of the screws as shown in Fig below These screws are also used to secure the individual 6KPM cards screen plate which can be subjected to significant forces from the attached cables See Figure 3 5 1c cs ie sree n a oo Figure 3 5 1c Top View 6KPM retaining screws hold Face Plate 3 5 2 Installing 6K PM Cards in the Magnum 6K25 Up to four front mounted 6KPM cards may be installed in one Magnum 6K25 Managed Fiber Switch unit Follow these steps to install a 6KPM Step 1 Remove top chassis cover See procedure in Section 3 5 1 above www GarrettCom com E 29 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Step 2 Placed Granddaughter board as shown in fig 3 5 2a and 3 5 2b on the chassis built in s
8. 24VDC and 125VDC POWER THEORY OF OPERATION The 48 VDC 24VDC and 125VDC power options are designed using diodes inside on each DC power input line behind the two external power connection terminals so that the power from an external POWER SWITCH i source can only flow into the hub ae This allows the Switch to operate ie only whenever DC power is GND correctly applied to the two inputs ONN It protects the Switch from incorrect DC input connections An incorrect polarity connection for example will neither affect the Switch its internal power supply nor will it blow the fuse in the internal power supply The manual power On Off Switch optional is used for powering the unit on and off when it is placed into or taken out of service B3 0 APPLICATIONS FOR DC POWERED SWITCHES Magnum 6K25 Fiber Switches are easily installed in a variety of applications where 48VDC 24VDC and 125VDC power is used as the primary power source The 48VDC 24VDC and 125VDC power configuration provides an Ethernet networking solution utilizing a special power supply in a managed Fiber Switch The 48 VDC solution is particularly useful in the telecommunication industry where it is common for facilities to operate on 48VDC power Such companies include regular and wireless telephone service providers Internet Service Providers ISPs and other communication companies In addition many high availability equipment services such as broadcast
9. 6K25 Managed Fiber Switch Installation and User Guide 04 06 GBIC 25 1000Mb Single 1550 9 125 4 0 LXSC25 mode GBIC 1000Mb Single 1550 9 125 4 0 ZXSC40 mode 70 GBIC 1000Mb Single 1550 9 125 3 0 ZXSC70 mode Note The use of either multi mode or single mode fiber to operate at 100Mbps speed over long distances i e in excess of approx 400 meters can be achieved only if the following factors are both applied e The 100Mb fiber segment must operate in full duplex FDX mode i e the full duplex factory default setting for 1 OOMbps fiber ports must be used and e The worst case OPB of the fiber link must be greater than the fiber cable s passive Attenuation Attenuation Cable loss LED aging loss Insertion loss safety factor 5 0 Introduction Magnum 6K25 Managed Fiber Switch Port Modules This chapter describes each Port Module PM including appearance functionality and status displays 5 1 Inspecting the Package and Product This section applies only to PMs shipped as separate items 1 e 6K25 PMs not factory installed in a Magnum 6K25 PM slot Examine the shipping container for obvious damage prior to installing a 6K25 PM notify the carrier of any damage you believe occurred during shipment or delivery Inspect the contents of this package for any signs of damage and ensure that the items listed below are included This package should contain 1 or more 6K25 PMs Installation inst
10. 6KPM Module Description cccecccceccecccceeeeseeeeeeseeeeeeeeeeeeeeeeeaaas 4 5 2 1 6KP6 RJMST Combo Module cece eeceecceccecceecesceeceecs 41 5 2 la 6KP6 RJIOST Combo Module ce cecceeceeceeceeees 42 5 2 16 6KP4 F10ST Module i ccco scniciccssiwcrentivocncnssdeonsesssadscedssenvestivedane 42 ofa oem 6 4 To BB iP Sm Module enn ee 43 5 2 2 6KP6 RIMSC FX SC connector cccccsscccseccsssensscesscescensscsesceuscens 43 5 2 3 6KP6 RJSSC CONNECCOL ccccceeecccesscceecceeecccessccesccesecseeesseenees 44 5 2 4 6KP6 RIJSSCL single mode COMNECEOL sscccceeeeeeeceeeeeeeeceeeeees 44 5 2 4a 6KP6 RJI1OST connector eeeseeeeseseeserresssreresresssrereeresesrereeeesesee 45 5 2 9 OKPS MTRJ FOr tact OP missir ketera NEE 45 5 2 5a 6KP6 MT10ST MTRJ Small Form Factor and port 46 5 2 6 6KP8 45MT MTRJ Small Form Factor ccce cee eeeeeeeeeeeeee 46 5 2 6K P8 MLC Form Factor eee ceccseccecceccecceccecceccscesceeceecs 47 5 2 8 6KP8 45LC LC small form factor Connector cccee cece eee 47 5 2 9 6KP8 RJ45 Twisted Pair 10 100Mb 8 Port 0 48 5 2 10 New PoE Power Inside model PI6KP8 45RJ MDIX 8 port 49 5 2 11 New PoE Power Pass through model P6KP8 RJ45 8 port 49 5 2 12 6KP8 45 2MT MTRJ Small Form Factor eee eeeeee 50 5 2 12a 6KP8 45 2LC single mode FX LC Small Form Factor 51 5 2 13 GBIC SXSC Gigabit fiber 1000Mb
11. ACT LED indicates receiving Activity on the port A fiber cable must be connected into a SFF port and the Link LK indicator for that port must be ON indicating there is a powered up device at the other end of the cable in order for a LK LED to provide valid indications of operating conditions on that port 10 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 2 2 3 Eight Port Copper Module 6K8 RJ45 The 6K25 Series s 8 port Copper port module model 6K8 RJ45 provides eight 10 100Mb switched RJ 45 ports The 10 100Mb switched ports normally as a default setting are independently N way auto negotiating and auto crossover MDIX for operation at 10 or 1OOMb speed in full or half duplex mode 1 e each independently selects a mode and speed to match the device at the other end of the twisted pair cable See Section 4 3 for auto negotiation and MDIX details The auto crossover feature will automatically determine the other side of connection to make the connection and eliminate the need of cross over cable On the model 6K8 RJ45 module there are four LEDs for each port two in the connector and two separate The LK Link LED indicates ready for operation on that port when lit The blinking ACT Activity LED indicates receiving Activity on that port when lit The 10 100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF when auto negotiation is not disabled Th
12. LK and www GarrettCom com 43 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 FDX HDX and 10 100 operation and the same face plate lettering While the functionality of these two modules is essentially the same the 6KP6 RJMSC is equipped with an SC type snap in connector instead of an ST type 5 2 0 6KP6 RJSSC 4 10 100Mbps RJ 45 Ports and 2 100Mbps single mode FX SC type snap in connector The Magnum 6KP6 RJSSC 6KP6 RJMSSC is also a Combo module 4 Port 10 100Mbps and 2 100 Mb SSC Fiber Port equipped with 4 dual speed copper ports and 2 Single mode SC type connectors It provides an advantage through combining copper 1 LINK 2 10 100 and Fiber functions in one module of the 6K25 Switch 3 activiry 4 ruLumaLe supporting four Copper and two single mode fiber network segments The 6KP6 RJSSC when installed in a Magnum 6K25 Switch operates on copper at the 100m distance The Fiber is single mode and cable lengths can be as much as 25 Km see Power Budget Section 4 5 Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and a FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates 100Mbps speed when lit and 10Mbps speed when off To distinguish the single mode 6 K6 RJSSC from the multi mode 6K6 RJMSC the label Sel M is
13. MNS 6K management software and a useful tool for first time user or email support GarrettCom com for further information 2 3 Features and Benefits Managed switching for high performance Ethernet LANs Magnum 6K25 Switches provide non blocking all ports can run at full speed at once performance with standard Managed Networks Software MNS 6K included They are typically used in LAN traffic centers with 16 to 24 100Mb ports and one or 2 Gigabit ports for backbone connections where managed network services are desired Switching services includes 802 1p QoS packet prioritization The Magnum 6K25 switching hardware supports QoS giving packet processing priority to priority tagged packets according to the IEEE 802 1p standard For port and application specific priorities the QoS software may be configured by the user Features Fiber Built In Magnum 6K25 Managed Fiber Switches are designed to naturally include fiber ports and support mixes of multi mode and single mode 10 Mb 1OOMb and 1000Mb speed full and half duplex classic Small Form Factor SFF and GBIC fiber connectors RJ 45 10 100 ports can also be configured in the mix of port types Modular design for port flexibility in a 1U space saving rack mount package The 1U Magnum 6K25 chassis has 4 slots for port configurations Family of 4 6 or 8 port modules allow the user to select the desired mix of port types amp speeds The port modules are normally factory installed and tes
14. MNS software is the same as the other 6K25 modules The fiber ports support fiber cabling distances according to the 1OBASE FL standard 1 e 2km distance for multi mode fiber Single mode for up to 10Km distance may be available as a special order configuration 2 2 8 Gigabit 1000Mbps port modules The Magnum 6K25 offered a wide option Gigabit speed with multiple choice for the modular slot While up to two Gigabit modules maxm can be configured in the modular slot The Gigabit port option for the modular slot comes in couple of different pe TX BLK RX configuration The Giga port has been offered as single Gigabit module comes in flavor of G 4 10 100 RJ 45 ports or G 2 1OOMb fiber 2 lt CT ACT 1 W ports as shown below TXE RX TX K RX 1 1000Mb Fiber SC 2 100Mb SC 14 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 The 6K25 Modules provide a GBIC opening for insertion of industry standard GBICs to provide Gigabit Gb media flexibility GBIC models are available for both multi mode 550m and single mode 10 25 40 70 km fiber options and for Gigabit copper as well with new models appearing often The 1000Mb Gigabit fiber port modules on the Magnum 6K25s are normally lf TX BLK RX p 3 set factory default to operate at AUTO mode for best fiber distance and performance The 1000Mbps SC fiber optic module on the Gigabit SX and Gigabit LX 1 1000Mb Fiber SC
15. SC Connector 51 5 2 13a GBIC LXSC amp ZXSC single mode SC Connector 32 PoC ORM BENK GE RE 52 6 0 TROUBLESHOOT IN Gibiscssitscctveccscstnccecccesccesscesucccscesesnsecdensesassvecswncatues 52 6 1 Before Calling for ASSIStanCe cccccccccssssssessseeeececeeeeeeeeeeaeseeeeesees 53 6 2 When Calling for ASsistance ccccccccccccccccceesesssseseeeeeeeceeeeeeeeeeeaas 53 6 3 Return Material Authorization RMA Procedure 54 6 4 Shipping and Packaging Information ccccccccccssssssssssessseeeeeeeeees 54 APPENDIX A WARRANTY INFORMATION 0 cccccscccceececeeeeceeeeees 55 APPENDIX B INTERNAL DC POWER SUPPLY OPTIONGW 55 APPENDIX C INTERNAL DC DUAL SOURCE POWER OPTION 58 1V Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Revisions 06 07 05 07 04 06 10 05 01 05 06 04 02 04 11 03 03 03 Minor update to power supply ranges Minor updates to notes for Power Substations connections minor updates as PoE modules option added on Sec 5 2 10 11 minor updates as MDIX support added on all RJ 45 port modules minor updates and tweak on LC port modules New port modules has been added and updates on Alarm contact Minor update and added Section 3 4 1 Alarm Contact option Minor updates Network standards amp Console port pin Assign Minor updates on power budget calculations Gigabit fiber Rev D 10 02 Updated the Rack Mount opti
16. The PoE RJ 45 ports act similar to regular RJ 45 ports except they have capability of providing power on each port to power up the PD devices per the TEEE802 3af PoE 6KP8 45 5 standard Only 4 x RJ 8 Port 10 100Mb Copper ports 45 10 100 ports maxm support POE Power Inside option in one 6K unit In this Fig the top 4 RJ45 ports are enhanced with POE gt E Oa eo Da option whereas as bottom 4 RJ 45 are COMHAR B 10 10 normal MDIX ports The 4 RJ45 POE 3 PoE 4 FULL HALF module are also available with mix n match with fiber modules Please check the ordering information Sec 1 2 for all the various PI6K PoE modules option The LEDs on 6KP8 RJ45 PoE module are slightly different compared to regular non PoE RJ 45 modules as shown in Fig 2 When the PoE port is in use the PoE LED is ON when connected properly to a 803 af compliant PD device on that port When non PoE devices are connected the PoE LED is OFF Operation of Ethernet data traffic is not affected by PoE LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK ACT as shown in the diagram PoE LEDs Summary e For PoE devices each RJ 45 PoE port supports only 802 3af complaint devices The PoE LED is ON when the attached PD is drawing power from the port e For non PoE devices connected the PoE port will act as a normal RJ 45 port and the PoE LED is OFF No power is being sent out from the port e The PoE ports in Magn
17. at the top of the faceplate of the 6K6 RJSSC 5 2 4 6KP6 RJSSCL 4 10 100 Mb copper port and 2 100Mbps single mode FX SC type snap in connector The Magnum 6KP6 RJSSC is also a Combo module equipped with 4 dual speed copper ports and 2 Single mode Long Reach SC type connectors It provides a combination of copper and Fiber functions in one module to the 6K25 Switches supporting four Copper and two single mode Long Reach fiber network segments The 6KP6 RJSSC when installed in a Magnum 6K25 Switch has copper supporting the 100m distance and Fiber supporting single mode fiber cable lengths of as much as 40 Km see Power Budget Section 4 5 www GarrettCom com gg I 44 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed for the copper port which is 100Mbps when the LED is ON and 10 Mb when the LED is OFF 5 2 4a 6KP6 RJ10ST 4 10 100 Mb copper port and 2 10Mbps multi mode FL ST type twist lock connector The Magnum 6KP6 RJ10ST is also a Combo module equipped with 4 dual speed copper ports and 2 multi mode 10 Mb fiber ST type connectors It provides a combination of copper and Fiber functions in one module to the 6K25 Switches support
18. both unshielded and shielded twisted pair cables 1 Using standard twisted pair media insert either end of the cable with an RJ 45 plug into the RJ 45 connector of the port Note that even though the connector is shielded either unshielded or shielded cables and wiring may be used 2 Connect the other end of the cable to the corresponding device 3 Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established www GarrettCom com E 23 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 NOTE for Power Substations In support of the IEEE 1613 Class 2 standard GCI advises that for substation applications the RJ 45 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity i e less than 2 meters or 6 5ft to the 6K25 It is not recommended to use these ports in substation applications to interface to field devices across distances which could produce kigh greater than 2500V levels of ground potential rise GPR during line to ground fault conditions The 6K25 passes the 1613 specifications for zero packet loss with fiber ports amp with RJ45 ports used as indicated here 3 2 5 Connecting Twisted Pair CAT5E or better Unshielded or Shielded The RJ 45 Gigabit ports of the Magnum 6K25 can be connected to the media types LOOOBASE T o
19. must be accommodated The fiber built in media capability is ideal for integrating future proof fiber cabling into the LAN structure Example 1 Magnum 6K25 Switch for a VLAN application Equipped with lots of useful features the Magnum 6K25 Managed switch is able to handle a VLAN application and provide a security and performance in an Ethernet network center A secure VLAN enabled network is simply an administratively configured broadcast domain The network administrator determines which ports and nodes are in which broadcast domains by setting membership profiles for each of them The Magnum 6K25 s VLAN capability can be developed in several types of Virtual LANs such as Port based VLANs or Tag based VLANs In an office environment where departments such as Finance Engineering R amp D and Marketing need to keep a secure LAN the 6K25 s VLAN feature will prevent traffic cross over among domains and thus from keep sensitive data and information controlled The Managed Magnum 6K25 equipped with VLANs capability is ideal for any application where a secure VLAN to multiple departments is needed The modularity of the 6K25 Managed Fiber Switch makes it an attractive choice for use in applications with LAN connections to an organization s multiple site offices The different offices can be easily connected together with the Fiber ports supported by the Magnum 6K25 Switch A main NT server in a secure area protected from earthquake or
20. ports New PI6KP8 45MT 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 2km mm FX MTRJ connectors New PI6KP8 45MLC 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 2km mm FX LC connectors New PI6KP8 45SLC 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 15km sm FX LC connectors New PI6KP8 45 2MT 6 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two normal RJ 45 10 100 ports twol00 Mb 2km mm FX MTRJ connectors New PI6KP8 452SLC 6 2 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 15km Sm FX LC connectors New PI6KP6 RJMST 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 2km mm FX ST connectors New PI6KP6 RJMSC 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 2km mm FX SC connectors New PI6KP6 RJSSC 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 20km sm FX SC connectors New PI6KP6 RJSSCL 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 40km sm FX SC connectors New PI6KP6 RJ10ST 4 2 port PoE module for 6ks with 48vdc PS w four POE power source and two 10 Mb 2km sm FL ST connectors GarrettCom Inc reserves the right to change specifications performance characteristics and or model offerings witho
21. send receive auto negotiation pulses and the second of the two connected devices is powered up i e when LINK is established for a port or the LINK is re established on a port after being lost temporarily www GarrettCom com E 37 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 e NOTE Some NIC cards only auto negotiate when the computer system that they are in is powered up These are exceptions to the negotiate at LINK enabled rule above but may be occasionally encountered When operating in 1OOMb half duplex mode cable distances and hop counts may be limited within that collision domain The Path Delay Value PDV bit times must account for all devices and cable lengths within that domain For Magnum 6K25 Fast Ethernet switched ports operating at 100Mb half duplex the bit time delay is SOBT 4 5 Flow control IEEE 802 3x standard Magnum 6K25 Switches incorporate a flow control mechanism for Full Duplex mode The purpose of flow control is to reduce the risk of data loss if a long burst of activity causes the switch to save frames until its buffer memory is full This is most likely to occur when data is moving from a 100Mb port to a 10 Mb port and the 10Mb port is unable to keep up It can also occur when multiple 1OOMb ports are attempting to transmit to one 1OOMb port and in other protracted heavy traffic situations Magnum 6K25 Switches implement the 802 3x flow contro
22. special twisted pair crossover cable when connecting to a hub or another switch Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit a FDX HDX LED to indicate full duplex mode when lit or half duplex when off and a 10 100 LED indicating 100Mb when lit or 10 Mbps when off Important Note The 10 100 RJ 45 ports are supported with Auto negotiation and Auto crossover MDIX which allow the RJ 45 ports to automatically Link with any RJ 45 device and eliminate the use of cross over cable NOTE for Power Substations In support of the IEEE 1613 Class 2 standard GCI advises that for substation applications the RJ 45 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity i e less than 2 meters or 6 5ft to the 6K25 It is not recommended to use these ports in substation applications to interface to field devices across distances which could produce kigh greater than 2500V levels of ground potential rise GPR during line to ground fault conditions The 6K25 passes the 1613specifications for zero packet loss with fiber ports amp with RJ45 ports used as indicated here www GarrettCom com 48 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 5 2 10 New PoE Power Inside model PI6KP8 45RJ MDIX 10 100Mb 8 port
23. switched port to which they are connected be at 1OOMb fixed speed Attachment to 10 100 auto negotiation ports typically will not work properly The 6K25 Switch s RJ 45 ports handle this situation by configuring the ports as per desire through MNS software port settings and can check the port status of each port after the change When Magnum 6K25 RJ 45 copper ports are set for auto negotiation and are connected to another auto negotiating device there are 4 different speed and F H modes possible depending on what the other device supports These are 1 100Mb full duplex 2 100Mb half duplex 3 10 Mb full duplex and 4 10 Mb half duplex The auto negotiation logic will attempt to operate in descending order and will normally arrive at the highest order mode that both devices can support at that time Since auto negotiation is potentially an externally controlled process the original highest order mode result can change at any time depending on network changes that may occur If the device at the other end is not an auto negotiating device the 6K25 s RJ 45 ports will try to detect its idle signal to determine 10 or 100 speed and will default to half duplex at that speed per the IEEE standard General information Auto negotiation per port for 802 3u compliant switches occurs when the devices at both ends of the cable are capable of operation at either 10 Mb or 100Mb speed and or in full or half duplex mode and can
24. to which port The Magnum Combo six port modules are also available with 4 MTRJ 100Mb mm SFF fiber and 2 10Mb fiber mm ST ports and with 4 RJ45 10 100 copper and 2 10Mb fiber mm ST ports The 4 RJ 45 2 10 Mb ST operation of the SFF fiber and the RJ 45 half of the module is as described for those port types above For detailed information about 10Mb mm ST fiber half of the module see Section 2 2 5 13 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 The Magnum Combo six port modules are also available with 4 MTRJ 100Mb mm SFF fiber and 2 10Mb fiber mm ST ports and with 4 RJ45 10 100 copper and 2 10Mb fiber mm ST ports The 4 RJ 45 2 10 Mb ST operation of the SFF fiber and the RJ 45 half of the module is as described for those port types above For detailed information about 10Mb mm ST fiber half of the module please check section 2 2 5 22 1 Four Port 10 Mb mm Fiber ST Modules n OO F GIS 1 TX GLKRX TX GLK RX 5 OO fee H F H 2 TX GLKRX A The 4port 10Mb ST fiber modules behave the same as the 8 100Mb ST fiber modules except for the 10Mb speed For ports numbering ports 1 2 5 6 are present ports 3 4 7 8 are not present The default setup on the 1OMb fiber module is half duplex which allows the Magnum 6K25 Switch to connect to any 1OMb hub or media converter or almost any other device with a 10Mb fiber Ethernet port User mode control per port through the
25. type plug in SFF Fiber multi modelOOBASE FX Fiber Port SC type snap in Fiber optic multi mode OOBASE FX Fiber Port ST type twist lock Fiber optic m mode 100BASE FX Fiber Port LOOOBASE FX GBIC modules Fiber Single mode connector types Fiber Port SC type Fiber optic single mode OOBASE FX Fiber Port LC type Fiber SFF single mode 1 OOBASE FX Fiber Port IOOOBASE FX GBIC modules LEDs Per Port LK Steady ON when media link is operational ACT ON with receiver port activity FDX HDX ON Full Duplex Mode OFF Half Duplex Mode 100 10 ON 100Mbps speed OFF 10 Mbps Operating Environment UL 60950 Component Parts temp rating 130 F 55 C IEC 60068 Type Test rating 40 to 185 F 40 to 85 C Storage 40 to 185 F 40 to 85 C Ambient Relative Humidity 5 to 95 non condensing Altitude 200 to 13 000 ft 60 to 4000m Conformal Coating option Request quote Packaging Enclosure Rugged High strength metal Suitable for stand alone or rack mounting Dimensions 1 70in H x 17 0in W x 9 0in D 4 32cm H x 43 2cm W x 22 9cm D Cooling method Fan cooled 3 7 cfm ea Management Console connector DB 9 for RS 232 null modem cable sometimes called an Xmodem cable Power Supply Internal AC Power Connector EC type male recessed at rear of chassis with adjacent manual ON OFF switch on AC models only Input Voltage 100 to 240 VAC auto ranging Input Frequency 47 to 63 Hz au
26. w four PoE power www GarrettCom com E 5 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 source and four 100 Mb 15km Sm FX LC connectors New P6KP6 RJMST 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 2km mm FX ST connectors New P6KP6 RJMSC 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 2km mm FX SC connectors New P6KP6 RJSSC 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 20km sm FX SC connectors New P6KP6 RJSSCL 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 40km sm FX SC connectors New P6KP6 RJ10ST 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 10 Mb 2km sm FL ST connectors 6K PoE Modules with 48SVDC Power Inside NOTE For configuring in 6K Switches having AC 125VDC power input Configuration options only one A B or C module slot of 6K Series switch with 48VDC power input may be configured with a PoE Modules New 6KAC PoE PS Power supply for PoE to 4 ports 60 watts mounts inside of a full width rack mount 6K switch with AC power input New 6K125VDC PoE PS Power supply for PoE to 4 ports 60 watts mounts inside of a full width rack mount 6K switch with 125VDC power input New PI6KP8 45RJ 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 10 100 auto negotiating auto cross RJ 45
27. will work properly with all the other connected devices with RJ 45 port whether it supports Auto negotiation or not e g 10Mb Hub media converter or fixed mode at 10Mb or 100Mb Half Full Duplex managed switch No cross over cable is required while using the 6K8 s copper port to other devices Operation is according to the IEEE 802 3u standard The Managed 6K25 Series Fast Ethernet copper ports can be set for either fixed 100Mb speed or for 10 100 F H N way auto negotiation per the IEEE802 3u standard The selection is made via MNS software The factory default setting 1s for auto negotiation At 10Mb or 100Mb fixed speed the user may select half or full duplex mode by MNS Software for each RJ 45 port separately For detail information See Section 10 1 at page no 52 of this manual to access the 6K MNS Rel 3 Software user guide www GarrettCom com E 36 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 One frequently used application for the Managed Magnum 6K25 Switch copper ports is to connect one of them using a fiber media converter to another Switch in the network backbone or to some other remote 100Mb device In this case it is desirable to operate the fiber link at 100Mb speed and at either half or full duplex mode depending on the capabilities of the remote device Standard commercially available Fast Ethernet media converters mostly do not support auto negotiation properly and require that the
28. 2 module w four RJ 45 ports and two 2km mm FX ST s 4 2 module w four RJ 45 ports and two 20km Sgl m FX SC s 4 2 module w four RJ 45 ports and two 40km Sgl m FX SC s 4 2 module w four MTRJ ports and two 10Mb 2km FL ST s 4 2 module w four RJ 45 ports and two 10Mb 2km FL ST s Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 For Gigabit module configuration options GBPM COTX One slot Gigabit 6K module for 6K25 Switches uses one 6K25 slot and provides one GBIC open transceiver port for a user selectable GBIC transceiver module GBIC SXSC GBIC transceiver module for use in GBPM xOTX one 1OOOBASE SX port with mm SC fiber connector GBIC LXSC10 GBIC transceiver module for use in GBPM xOTX one 1OOOBASE LX LH port with 1310nm sgl mode SC 10km fiber connector GBIC LXSC25 GBIC transceiver module for use in GRPM xOTX one 1000BASE LX LH port with 1310nm sgl mode SC 25km fiber connector GBIC LXSC40 GBIC transceiver module for use in GBPM xOTX one 1OOOBASE ZX port with 1550nm sgl mode SC 40km fiber connector GBIC transceiver module for use in GBPM COTX one LX port with mm SC fiber connector GBIC LXSC70 GBIC transceiver module for use in GRBPM xOTX one 1OOOBASE ZX port with 1550nm sgl mode SC 70km fiber connector GBIC TP GBIC transceiver module for use in GBPM xOTX one 802 3ab 1O00BASE T port RJ 45 connector 6KM BLNK Blank cover for one 6K25 A B or C module slot
29. 232 DB 9 Console Com port Serial port pin assignments DB 9 Console port connector Pin Signal Description 1 CD Carrier detect not used 2 RXD Receive Data input 3 TXD Transmit Data output 4 open not used 5 GND Signal Ground 6 9 open not used 34 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 The above provided information enables a managed station a PC or Console terminal to connect directly to the switch using a straight through cable Note The Null Modem DB 9 cable is optional and can be order from the factory along with the unit NOTE for Power Substations In support of the IEEE 1613 Class 2 standard GCI advises that for substation applications the serial RJ 45console_ports are intended for temporary connectivity to other equipment such as PCs Since the console port connection is temporary it is excluded from IEEE 1613 packet loss testing per the 1613 standard defined test procedure 4 0 OPERATION This chapter describes the functions and operation of the Magnum 6K25 Switch 4 1 Switching Functionality A Magnum 6K25 provides switched connectivity at Ethernet wire speed among all of its ports The Magnum 6K25 supports10 100Mbs for copper media and 10 or 1OOMb separate traffic domains for fiber ports to maximize bandwidth utilization and network performance All ports can communicate to all other ports in a Magnum 6K25 but local traffic on a port will not consume any of the bandw
30. 25 Managed Fiber Switch 8 22 1 Magnum 6K25 and 6K25R chassis cccscceceeeeeeeeeeeeeeeeeeeees 9 2 2 2 Eight port SFF fiber modules 100Mb fiber cceeeeeeeeees 10 22 5 Eight Port Copper Module 6K8 RJAS5 cccccccesccccesecceeeeeeeeaeeeeeeaes 11 2 2 4 New PoE Power Inside model 10 100Mb 8 port 0ccceeeeeeees 12 2 2 5 New PoE Power Pass through model 10 100Mb 8 pott 0cc000 12 2 2 6 Six Port 4 2 Combo Modules ST or SC eee eee cece eeeeeeees 13 2251 Four Port 10 Mb mm Fiber ST Modules eeeeeeeees 14 2 2 8 Gigabit LOOOMbps port modules 2 0 00 eesseeeeeeseeeeeeeeeeeeees 14 2 2 9 Packet Prioritization 802 1 p QOS cccccccsssesseeseeeeeeeeeeeeeeenaes 15 2 2 10 Frame Buffering and Flow Control cc cccccsssssseeeseeeeeeeeees 15 2 2 11 Managed Network Software MNS 6K for 6K25 Series 16 3 0 INSTALLA TION cossis a E 21 3 1 Locating Magnum 6K25 Switches cc seeeseeeeeeeeeeeeeeeeeeaeeaeeeeeees 2l 3 2 Connecting Ethernet Media ccecccsssseeeeccceeceeeeeeeaeaeesseseeeeeeeeeees 22 3 2 1 Connecting Fiber Optic ST type twist lock ee 22 ae Connecting Fiber Optic SC type Snap In ee 23 ee Connecting Single Mode Fiber Optic ccccceeeesssseseeeeeeeeeeeees 23 324 Connecting Twisted Pair RJ 45 CAT3 CATS cccccesecceeeeeeeeees 23 3 2 5 Connecting Twisted Pair CATSE OF ccc
31. 25VDC power supply is identical to that of the standard AC powered models B6 0 ORDERING INFORMATION To order the optional 48VDC power supply factory installed add a suffix of 48VDC after the product s standard model Example Magnum 6K25R 48VDC Similarly to order the optional 24VDC or 125VDC industrial specific power supply factory installed add a suffix of 24VDC or 125VDC after the product s standard model Example Magnum 6K25 24VDC Magnum 6K25 125VDC B7 0 TROUBLESHOOTING Please refer to Section 6 0 for troubleshooting APPENDIX C Internal DC Dual Source Power Option C1 0 SPECIFICATIONS FOR MAGNUM 6K25 FIBER SWITCH Power Supply Internal 48VDC Dual Source model Dual Src 48V DC Power Connector First Source A A 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 36 70 VDC Power Supply Internal 24VDC Dual Source model Dual Src 24V DC Power Connector First Source A he 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 20 36 VDC Power Supply Internal 125VDC Dual Source model Dual Src 24V DC Power Connector First Source A er 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each a
32. E 802 3 L1OBASE T IEEE 802 3u 100Base TX 10OBASE FX IEEE 802 3z 1000BASE X Ethernet Auto negotiation IEEE 802 3ab 1OOOBASE X Ethernet IEEE 802 1p Priority protocol IEEE 802 1d Spanning tree protocol IEEE 802 1w Rapid Spanning tree protocol IEEE 802 1g VLAN Tagging IEEE 802 3x Flow Control Maximum 10 Mbps Ethernet Segment Lengths Unshielded twisted pair 100 m 328 ft Shielded twisted pair 150 m 492 ft 1OBASE FL multi mode fiber optic 2 km 6 562 ft 1OBASE FL single mode fiber optic 10 km 32 810 ft Maximum Standard Fast Ethernet Segment Lengths 1OBASE T CAT 3 4 5 UTP 100 m 328 ft 100BASE TX CAT 5 UTP 100 m 328 ft Shielded twisted pair 150 m 492 ft 1O00BASE FX half duplex multi mode 412 m 1350 ft 1O00BASE FX full duplex multi mode 2 0 km 6 562 ft 1OOBASE FX half duplex single mode 412 m 1350 ft 1OOBASE FX full duplex single mode 20 0 km 66K25 ft 1OOBASE FX full duplex Long Reach 40 0 km 122K ft Maximum Standard Gigabit Ethernet Segment Lengths 1O00BASE T CATSE or higher is recommended 100 m 328 ft 1O00BASE SX full duplex multi mode 62 5um cable 220m 1O00BASE SX full duplex multi mode S50um cable 550m 1O00BASE LX full duplex single mode 62 5um cable 5Km Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Fiber Multi mode connector types supported Fiber Port ST type twist lock Fiber multi mode 1OMb 1OBASE FL Fiber Port MTRJ
33. EEE 802 3z standard 1000Mbps distance limits 1 e www GarrettCom com E 51 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 550m at full duplex The GBIC transceiver is fastened using snap in clips Insert the transceiver take care to insert it the right way up arrows on top until it clicks in space While removing the transceiver press the clips on either side of the transceiver at the same time and pull the transceiver out Each port has an Activity ACT LED indicating packets being received and a Link LK LED indicating proper connectivity with the remote device when lit 5 2 13a GBIC LXSC amp ZXSC Gigabit fiber L000Mb single mode SC Connector The Magnum GBIC LXSC ZXSC is a single mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out The Gigabit fiber ports are most popular as server to switch and switch to switch applications It supports cable distances up to the IEEE 802 3z standard 1000Mbps distance limits 1 e 10 25 40 or 70Km at full duplex and depend upon the Gigabit modules used Each port has an Activity ACT LED indicating packets being received and a link LK LED indicating proper connectivity with the remote device when lit 5 2 14 6KM BLNK The 6KM BLNK is a blank face plate or cover plate that must be installed in any empty 6K25 PM slot to maintain proper cooling air flow safety etc Two screws underneath the front panel ho
34. Environmental Standard for Electric Power Substations See also Note for Power Substations in Section 3 2 4 3 6 1 and 5 2 9 IEC 61850 EMC and Operating Conditions Class C for Power Substations Warranty Three years return to factory Made in USA NEBS Testing and Certification NEBS certified Email sales GarrettCom com for details Magnum 6K25 Managed Fiber Switch 1 2 MODEL Installation and User Guide 04 06 Ordering Information Magnum Managed Fiber Switch DESCRIPTION Magnum 6K25 Magnum 6K25 Managed Fiber Switch base unit May be configured with a selection of 10 100 1000 6K25 fiber and copper port connector types 25 total ports max Wire speed filtering and forwarding across all ports 802 3x flow control 802 1p priority packet processing self learning 4K node address table large 240KB packet buffers for 10 100 and 120KB for 1000Mb Plug and play switching services front mounted LEDs internal auto ranging AC power supply 19 rack mounting brackets For licensed managed networks software see MNS materials Magnum 6K25R Reverse model same as Model 6K25 except the user ports and the power input connectors are in the rear Two sets of LEDs both rear and front provide duplicate status data for viewing from either side Magnum 6K25 48 VDC Magnum 6K25R 48VDC Magnum 6K25 24VDC Magnum 6K25R 24VDC Magnum 6K25 125VDC Same as 6K25 except the power input is 48 VDC Same as 6K25R except the power inp
35. agnum 6K25 units have address table capacities of 4K node addresses suitable for use in larger networks They are self learning so as nodes are added removed or moved from one segment to another the 6K25 Switch automatically keeps up with node locations An address aging algorithm causes least used addresses to fall out in favor of frequently used addresses To reset the address buffer cycle power down and up 4 2 Status LEDs For all Magnum 6K25 models PWR Power LED ON when external power is applied to the unit LK Steady ON Link status for 10 Mbps and 100Mbps operation ACT ON with port activity for 10 Mbps and 100Mbps operation F H Full Half duplex LED ON when the port is running full duplex OFF for half duplex 100 10 Speed LED ON when the speed is 1OOMbps OFF when the speed is 10 Mbps 4 3 Up link MDI MDIX on RJ 45 port modules for port 1 only The upper part of the copper port module has a manual Up link switch located on the inside of the unit on the port module board next to the RJ45 port 1 which it controls It enables the port s cable to be cascaded X to a 10 100Mb repeater or switching hub in the network The manual Up link switch position is configured as position as default factory setting where used for all copper module or combo modules 4 4 Auto Cross MDIX and Auto negotiation for RJ 45 ports The RJ 45 ports independently support auto cross MDI or MDIX in auto negotiation mode and
36. and is equipped with five 5 screw down lead posts If it is the reverse model it is located on the left rear The primary terminals are identified as positive A negative A and the secondary power terminals as negative B positive B The chassis earth or ground GND is a threaded post with a 6 nut The Dual Source terminal block for the 24VDC and 125VDC are similar Figure C5 0 48VDC Dual Source wiring connections to the External Terminal Block on a Magnum 48VDC with Dual Source option 36 70VDC 36 70VDC GND Note The GND should be hooked up first The 6K25 unit has a floating ground so the www GarrettCom com E 59 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 user may elect to Ground either or terminal to suit the customer s use Before connecting hot lines to the Terminal Block of 48VDC 24VDC or 125VDC always use a digital voltmeter to measure the output voltage of the power supply and determine the lead which is more ve potential The more ve voltage lead from 48V or 48V supply must be connected to the post labeled The connection procedure is straightforward Simply connect the DC leads to the Switch s power terminals positive and negative screws The use of Ground GND is optional it connects to the Switch chassis Ensure that each lead is securely tightened The 24VDC amp 125VDC terminal block on Magnum 6K25 s is similar t
37. bps amp 2 port 100Mb Multi Mode Ag combo module with copper and fiber Small Form Factor MTRJ type ports The small sizes of MTRJ connectors give an advantage of placing more fiber ports on one module The 2 LINK 10 100 6KP8 45 2MT is equipped with six 10 100 RJ 45 ports and two 3 ACTIVITY Q FULL HALF 100Mb MTRJ fiber ports When installed in a Magnum 6K25 Switch it supports the standard distances as mentioned on 5 2 3 and the LEDs also act similarly 5 2 12a 6KP8 45 2LC 6 10 100Mbps RJ 45 and 2 100Mb single mode FX LC Small Form Factor The Magnum 6KP8 6 Port 101s amp 2 port 100Mbps 45SLC eight port Module is a combo module with copper and SingleMode Ady LC fiber Small Form Factor LC type fiber ports The small size of LC connectors give an advantage of placing more orts on one module The 6KP8 G unk mw 45 2SLC is equipped with 6 10 100 RJ 45 ports and 2 Single CP eee 4 FULLHALF mode fiber ports When installed in a Magnum 6K25 Switch it supports the standard distances as mentioned on 5 2 4 and the LEDs also act similarly 5 2 13 GBIC SXSC Gigabit fiber 1000Mb multi mode SC Connector The Magnum GBIC SXSC is a multi mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out The Gigabit fiber ports are most popular as server to switch and switch to switch applications It supports cable distances up to the I
38. cccsssecccecessecceeeeeseeceeeeees 24 3 3 Table Top or Shelf MOunting cc cccesssessssseseseeeeeeeeeeeeeeeeaeeaeeeeees 24 3 3 1 Rack mounting for 19 RETMA racks 6K25s ccceee 25 3 3 2 Rack mounting Reverse version of the Magnum 6K25s 26 3 4 Powering the Magnum Managed Fiber Switch cccccceeeeeees 26 3 4 1 Alarm Contacts for monitoring internal power Software Traps 27 3 5 6K25 Port Module 6KPM Installation 27 3 5 1 Preparation for Installing and Removing 6KPMsS cccceeees 28 Joz Installing 6KPM Cards in the Magnum 6K25 0 ee 29 3 6 Connecting the Console Terminal to Magnum 6K2 5 06 34 3 6 1 RS 232 DB 9 Console Com Serial port pin assignments 34 4 1 Switching Functionality cc cccssssssssssseeecceccccceeeeeaeeeesssssseeeeeeeeees 35 4 2 e LE D eai a E E EEEE 36 4 3 Up link MDI MDIX on RJ 45 port modules for port 1 only 36 4 4 Auto Cross MDIX and Auto negotiation for RJ 45 ports 36 4 5 Flow control IEEE 802 3x standard oo cece ceeceecceccecceccescecceecees 38 4 6 Power Budget Calculations for Magnum 6K25 PM s with Fiber Media 39 5 0 INTRO MAGNUM 6K25 MNGD FIBER PORT MODULES 40 www GarettCom com iii Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 5 1 Inspecting the Package and Product cccseeeeeeceeeeeeeeeeeeeeeeneeees 40 a2
39. dampened in alcohol Make certain the connectors are clean before connecting Note One strand of the duplex fiber optic cable is coded using color bands at regular intervals you must use the color coded strand on the associated ports at each end of the fiber optic segment 3 Connect the Transmit TX port light colored post on the Magnum PM to the Receive RX port of the remote device Begin with the color coded strand of the cable for this first TX to RX connection 4 Connect the Receive RX port dark colored post on the PM to the Transmit TX port of the remote device Use the non color coded fiber strand for this a The LINK LED on the front of the PM will illuminate when a proper connection has been established at both ends and when power is ON in the unit If LINK is not lit after cable connection the normal cause is improper cable polarity Swap the fiber cables at the PM connector to remedy this situation www GarrettCom com E 22 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 3 2 2 Connecting Fiber Optic SC type Snap In The following procedure applies to installations using a PM with SC type fiber connectors 1 e using 6K MSC 6K SSC single mode When connecting fiber media to SC connectors simply snap on the two square male connectors into the SC female jacks of the 6KPM until it clicks and secures 3 2 3 Connecting Single Mode Fiber Optic When using single mode fiber cable be su
40. different compared to regular non PoE RJ 45 modules as shown in Fig 2 When the PoE port is in use the PoE LED is ON when connected properly to a 803 af compliant PD device on that port When non PoE devices are connected the PoE LED is OFF Operation of Ethernet data traffic is not affected by PoE LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK ACT as shown in the diagram 2 2 6 Six Port 4 2 Combo Modules 4 10 100 RJ 45 and 2 100Mb fiber 4 RJ 45 2 100Mb ST or SC The combo six port modules are combinations of copper and fiber media available as four 10 100 switched RJ 45 copper ports and two 100Mb switched multi mode fiber ST SC or single mode SC or Long Reach SC ports For ports numbering ports 1 3 5 7 are copper ports 2 and 6 are fiber ports 4 and 8 are not present The four RJ 45 ports operate just like the 8 port copper module with auto cross MDIX feature to eliminate the use of cross over cable and the two fiber ports operate at 1OOMbps full duplex default User mode control per port through the MNS software is also the same On Magnum 4 2 Combo modules there are four LED s for each RJ 45 port which indicate status the same as described for the 6K8 RJ45 in Section 2 2 3 above The fiber port s LEDs indicate status the same way as described for the SFF fiber modules in Section 2 2 2 above Color coding on the panel of the module shows which LEDs belong
41. e FDX HDX LED is ON to indicate full duplex operation and OFF to indicate half duplex mode A twisted pair cable must be connected into an RJ 45 port and the Link LK indicator for that port must be ON indicating there is a powered up device at the other end of the cable in order for a LK LED to provide valid indications of operating conditions on that port Using the 6K8 Series MNS 6K management software the user may disable auto negotiation and fix the desired operation of each RJ 45 port User may select 10Mb or 1OOMb speed and full or half duplex mode per port as per user requirement See Magnum MNS 6K Software Manual for details info www GarrettCom com E 1 8 Port 10 100Mb Copper ports Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 2 2 4 New PoEK Power Inside model PI6KP8 45RJ MDIX 10 100Mb 8 port The New PoE RJ 45 ports act similar to regular RJ 45 ports except they have capability of providing power on each port to power up the PD devices per the 6KP8 45R J IEEE802 3af PoE standard Only 4 x RJ 8 Port 10 100Mb Copper ports 45 10 100 ports maxm support POE Power Inside option in one rack mounted 6K unit The power inside PoE option is factory configured and gt lt equipped with the Oe B 10 10 necesasary power option to support four 3 PoE 4 ean 802 3af PoE pd devices The 4 RJ45 POE module are also available with mix n match with fiber modules P
42. e chassis cover by loosening the 4 screws and bracket while holding it down firmly Figure 3 5 3a Top View 6 retaining s crews shown by arrows Step 3 Remove 6KPM Card Carefully and gently pull out the daughter board from the latching connectors using both hands gripping the board near the latch up connectors as shown in Fig 3 5 3b If the now empty slot is to remain unused be sure to install a 6KPM BLNK face plate cover Figure 3 5 3b Removing a 6KPM Card If another 6KPM card is replacing the one that has been removed follow the steps as described for installing a 6PM card discussed in Section 3 5 1 33 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 3 6 Connecting the Console Terminal to Magnum 6K25 Management Use a DB 9 null modem cable to connect the Magnum6K25 Console Port the RS 232 port on the 6K25 Switch to the your PC so that your PC becomes the 6K25 s Console Terminal Note The DB 9 cable does not include with the 6K25 unit package Console DB 9 Port CONSOLE Rear View of Magnum 6K25 Typical Console Port is on the Rear of Reverse 6K25 Models Note For detail description of Managed Network Software MNS 6K and Magnum 6K25 Switch configuration for Network Management please refer to Magnum 6K25 Software Manual available on GarrettCom s FTP site Detail info about the MNS is available on 2 2 9 see page no 13 of this manual 3 6 1 RS
43. ebsite http www GarrettCom com email support garrettcom com Federal Communications Commission Radio Frequency Interference Statement This equipment generates uses and can radiate frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference Canadian Emission This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil respecte toutes les exigences du R glement sur le mat riel du Canada Cet appareil est Classe A 11 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 TABLE OF CONTENTS Page LO SPECIFICA TIONS scrissi 1 1 1 MCW Cal Specioal ONS crine E Eaa l pe Orderme THO MWA O siesena E 4 20 INTRODUCTION cisieniiine a a ES 7 al Inspecting the Package and Product cccccsseseeeeeeeeeeeeeeeeaeeeeeeeeees 7 2 2 Product Description Magnum 6K
44. ers publishers newspaper operations brokerage firms and other facilities often use a battery backup system to maintain operations in the event of a power failure It is also frequently used for computer system backup management and operations monitoring equipment The 24VDC and 125VDC solution are particularly useful in the Industrial environment where it is common facilities to operate on 24VDC or 125VDC power The 125VDC solution is mainly used in power utilities such as electrical substations electrical generating plants etc The 24VDC applications are mainly in the Industrial environment such as factory floor HVAC equipment military equipment etc 56 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 B4 0 INSTALLATION This section describes the installation of the 48 VDC 24VDC and 125VDC power source leads to the 48 VDC 24VDC and 125VDC power terminal block on the Magnum 6K25s see figure at right In this picture the 48 VDC terminal block on the Magnum 6K25 is located on the rear of the unit and is equipped with three 3 screw down lead posts It is similar for 24VDC and 125VDC options on Magnum 6K25 36 70VDC The leads are identified as negative positive Figure B4 0 48VDC Terminal Block on Magnum 6K25 48VDC and chassis ground GND The actual connection procedure is very straightforward Simply connect the leads to the Magnum unit beginning with ground Ensure that each lead
45. fans www GarrettCom com E 21 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 3 2 Connecting Ethernet Media The Magnum 6K25 Switches are specifically designed to support all standard Ethernet media types within a single Switch unit This is accomplished by using a family of different port Modules which can be individually selected and configured per port See Section 2 4 for a description of the PMs The various media types supported along with the corresponding IEEE 802 3 and 802 3u standards and connector types are as follows IEEE Standard Media Type Max Distance Port Module Fiber 100BASE FX mm Fiber 220m ft GBIC SXSC sel m Fiber 5Km GBIC LXSC 100BASE FX mm Fiber 2 0km 6 562 ft 6K6 MSC MST sgl m Fiber 18 0km 95K ft SSC SSCL small form factor mm Fiber 2 0km 6 562 ft 6K8 MTRJ MLC small form factor sgl m Fiber 15 km 6KP8 SLC Copper 1OBASE T and 1OOBASE TX twisted pair 100m 328 ft 6K8 RJ45 L mm multi mode 2 sgl m single mode 3 2 1 Connecting Fiber Optic ST type twist lock The following procedure applies to installations using a PM with ST type fiber connectors This procedure applies to ports using a 6K25 module MST type port 1 Before connecting the fiber optic cable remove the protective dust caps from the tips of the connectors on the PM Save these dust caps for future use 2 Wipe clean the ends of the dual connectors with a soft cloth or lint free lens tissue
46. fingers as shown below in Fig 3 5 2f on the top of the latching connectors until the connectors latched up securely Figure 3 5 2f Securely latching up 6KPM Cards into a Magnum 6K25 www GarrettCom com E 31 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 NOTE All 6KPM slots need not be filled in order for the Magnum 6k25 unit to be operational When leaving 6KPM slots empty always use a face plate Magnum 6K8 BLNK to cover the slot opening in the front panel This will maintain proper cooling air flow safety and operation as required by FCC CE and other regulations Step 6 Now screw down the m daughter board with 6 440 screws so that it he ae LY holds the daughter board WN ja Fi securely The figure below shows the top view of 6KPM card after mi r successfully installing the 6KPM cards inside the Magnum 6K25 dig le Fig 3 5 28 Top View 6KPM Module installed inside a 6K25 Step 7 Once the installation of granddaughter and daughter modules is done the front panel screen plates need to be placed on the front of the chassis cover to complete the installation process for that port module The front panel screen plate comes along with the package of port module separately along with brackets and 6 256 flat head screws The brackets and screws have been installed inside of the top cover as shown in Fig 3 5 2h
47. fire hazards can be connected to the full duplex Gigabit Fiber port Full duplex future proof fiber media can easily connect long distance subnets www GarrettCom com E 19 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 and provide a stable secure network to all applications The SNMP management capability of the Magnum 6K25 Switch helps create a database of all the network subnets to easily manage the network Example 2 In another application a managed switch is needed to provide an Ethernet backbone for a diversified network with multiple subnets The back bone consists of high speed LAN segments supported by 100Mbps full duplex future proof fiber media to provide secure long distance LAN connections The entire network is sharing a higher bandwidth Gigabit enabled data mining server for the vital database located in a separate secured building The copper ports are required for multiple subnets inside the building The entire spread network will be manageable to provide easy detectable uninterrupted support through a viewable SNMP monitor The Magnum 6K25 Managed Fiber Switch equipped with the mix of copper and fiber ports provides an economical and seamless solution to the requirements The user configurable Magnum 6K25 provides an extra boost to the network requirements by providing copper fiber media along with the higher bandwidth support of 10 100 and 1000Mb The user can utilize the SNMP feature eq
48. holes prepared for each of the mounting arrangements Users may choose the mounting arrangement most suitable for their installation Standard Flush Mount Bracket Mid Range Mount or 5 Set Back Bracket Rear Mount Bracket Fig 3 3 2 Reverse Magnum 6K25 units rack mounted in a frame 3 4 Powering the Magnum Managed Fiber Switch The Magnum 6K25 Switches incorporate an internal universal power supply and have a recessed male IEC connector for the AC power cord at the left rear A manual power ON OFF switch is adjacent A six foot 115 VAC 60 Hz standard power cord is supplied with each unit shipped within the United States and Canada The auto ranging power supply supports installation environments where the www GarrettCom com E 26 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 AC voltage is from 90 to 260 volts with a power input frequency between 47 and 63 Hz The 25 port units will consume over 20 watts of power typically When connecting the Ethernet cabling there is no need to power down the unit Individual segments can be connected or disconnected without concern for AC power related problems or damage to the unit Power supply options are available to suit the 6K25 Switches to special high availability communications and or heavy industrial grade applications including 48VDC 24VDC and 125VDC with single DC input 48VDC 24VDC and 125VDC with dual source DC input See the Appendices
49. idth on any other port Magnum 6K25 units are plug and play devices There is no software configuring necessary to be done for basic operation at installation or for maintenance The only hardware configuration settings are user options for an UP LINK Switch resides inside the unit on the 6K8 RJ45 Optional Half Full duplex mode and 10 or 100Mbps selection for the switched ports must be configured through MNS software per unit as per the requirement The internal functions of both are described below Filtering and Forwarding Each time a packet arrives on one of the switched ports the decision is taken to either filter or to forward the packet Packets whose source and destination addresses are on the same port segment will be filtered constraining them to that one port and relieving the rest of the network from having to process them A packet whose destination address is on another port segment will be forwarded to the appropriate port and will not be sent to the other ports where it is not needed Traffic needed for maintaining the operation of the network such as occasional multi cast packets are forwarded to all ports The Magnum 6K25 Switches operate in the store and forward switching mode which eliminates bad packets and enables peak performance to be achieved when there is heavy traffic on the network www GarrettCom com E 35 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Address Learning All M
50. ing four Copper and two 10Mb of ST fiber network segments The 6KP6 RJIOST when installed in a Magnum 6K25 Switch has copper supporting the 100m distance and Fiber supporting multi mode fiber cable allow to connect the legacy network of 1OMb requirement in the network Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed for the copper port which is 10Mbps when the LED is ON and 10 Mb when the LED is OFF 5 2 5 6KP8 MTRJ 8 100Mb multi mode FX MTRJ Small Form factor Magnum 6KP8 MTRJ is a multi mode fiber optic 8 port module equipped with a small form factor MTRJ type 6KP8 MTRJ amp connector It looks almost like small form factor 8 Port 100Mbps Multi Mode Fiber port an RJ 45 port but it is black in color The MT RJ s small size and ease of connection make it a good choice for 1 OOMbps fiber to the desktop Ethernet connectivity When installed in a Magnum 6K25 Switch it ACTIVITY 2 supports fiber optic cable G FULL HALF distances up the EEE standard LINK 100Mbps distance limits 1 e 45 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 typically 2km at full duplex and 412m at half duplex The functionality of this 1 OOBASE FX multi mode 8 Port module is es
51. is eliminates the propagation of bad packets enabling all www GarrettCom com E 15 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 of the available bandwidth to be used for valid information While other switching technologies such as cut through or express impose minimal frame latency they will also permit bad frames to propagate out to the Ethernet segments connected The cut through technique permits collision fragment frames which are a result of late collisions to be forwarded which add to the network traffic Since there is no way to filter frames with a bad CRC the entire frame must be present in order for CRC to be calculated the result of indiscriminate cut through forwarding is greater traffic congestion especially at peak activity Since collisions and bad packets are more likely when traffic is heavy the result of store and forward operation is that more bandwidth is available for good packets when the traffic load is greatest When the Magnum 6K25 Switch detects that its free buffer queue space is low the Switch sends industry standard full duplex only PAUSE packets out to the devices sending packets to cause flow control This tells the sending devices to temporarily stop sending traffic which allows a traffic catch up to occur without dropping packets Then normal packet buffering and processing resumes This flow control sequence occurs in a small fraction of a second and is trans
52. is securely tightened Note The GND should be hooked up first The 6K25 unit has a floating ground so the user may elect to Ground either or terminal to suit the customer s use Before connecting hot lines to the Terminal Block of 48VDC 24VDC or 125VDC always use a digital voltmeter to measure the output voltage of the power supply and determine the lead which is more ve potential The more ve voltage lead from 48V or 48V supply must be connected to the post labeled An ON OFF manual switch is optional for DC power This can be used to cut off power connections and as a RESET for the Magnum 6K25 Switch B4 1 UL Requirements for DC powered units Minimum ISAWG cable for connection to a Centralized DC power source Minimum 14AWG cable for connection to a earthing wiring Use only with Listed 10 A circuit breaker provided in building installation Complies with FDA radiation performance standards 21 CFR subchapter J or equivalent 7 Fastening torque of the lugs on the terminal block 9 inch pound max 6 Centralized DC Power Source cable securement use at least four cable ties to secure the cable to the rac k at least 4 inches apart with the first one located within 6 inches of the terminal block www GarrettCom com E 57 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 B5 0 OPERATION Operation of Magnum 6K25 Switches with the optional 48 VDC 24VDC and 1
53. istance limits 1 e typically 2km at full duplex and half duplex Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed if the LED is ON 1OOMbps if it is OFF 1OMbps 5 2 1b 6KP4 F10ST 4 10Mb multi mode FX ST twist lock Module The Magnum 6KP4 F10ST 6KP4 RJ10MST is a 10Mb multi mode 4 Port 10Mb ST Fiber Port fiber module with 4 ST Fiber ports All four fiber ports are ST connectors and configured as 10Mb 3 Half duplex by default The 10Mb ST fiber ports allow the user to connect their legacy 1OMb network G FULL HALF to the Magnum 6K25 switch They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports It supports distances according to the 10Base FL standard i e 2Km distance for multi mode fiber Single mode for 10Km distance may be available as a special order Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and FDX HDX LED indicating full duplex mode when lit or half duplex if off 42 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 5 2 1lc 6KP4 FLSTFX 2 10Mb amp 4 Port 10Mb ST Fiber Port 2 100Mb multi m
54. ixed Media Fiber Hub 16 port 10 100 auto sensing Dual Speed 8 port and 16 port 10 100 auto sensing HUBS Personal Switches 10 LOOMb 8 port dual speed Auto negotiable with fiber option Personal Hubs LOOMb or 10 LOOMb 8 port with 2 switched ports 1 fiber built in Personal Hubs 10Mb series 8 port AUI stackable to 5 high optional BNC of fiber port 8 or 9 port and 4 or 5 Port Personal Hubs w man up link sw Media Converters 1OMb and 100Mb series All media combinations incl fiber ST SC mm single mode The X line of configurable MiXed Media products Stackable Concentrators SNMP optional 13 Ports Mini Concentrators 7 Ports Repeaters 2 Ports Repeater Port Modules RPMs 6 types for Ethernet media COAX Transceivers 10Mb series Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 1 0 1 1 SPECIFICATIONS Technical Specifications Performance Filtering Forwarding Rate Ethernet 14 880 pps Fast Ethernet 148 800 pps Gigabit Ethernet 1 488 000 pps Switching Processing Type Store and Forward with IEEE 802 3x full duplex flow control non blocking Data Rate 10Mbps 100Mbps and 1000Mbps Address Table Capacity 4K node self learning with address aging Packet buffer size 240KB for 10 100 and 120KB for 1000Mb Latency 5 us packet time 100 to 1OOMbps 15 us packet time 10 to 10 Mbps and 10 to 1OOMbps Network Standards and Compliance hardware Ethernet V1 0 V2 0 IEE
55. k equipment models and related hardware including personal computers workstations terminals and printers plus the various network media types being used 4 A record of changes that have been made to your network configuration prior to the occurrence of the problem Any changes to system administration procedures should all be noted in this record 6 3 Return Material Authorization RMA Procedure All returns for repair must be accompanied by a Return Material Authorization RMA number To obtain an RMA numter please use this URL https rma garrettcom com rma rma_request_noaccount php to fill out the form Please have the following information readily available Name and phone number of your contact person Name of your company institution Your shipping address Product name Serial Number or Invoice Number Packing List Number or Sales Order Number Date of installation Failure symptoms including a full description of the problem GarrettCom will carefully test and evaluate all returned products will repair products that are under warranty at no charge and will return the warranty repaired units to the sender with shipping charges prepaid see Warranty Information Appendix A for complete details However 1f the problem or condition causing the return cannot be duplicated by GarrettCom the unit will be returned as No Problem Found GarrettCom reserves the right to charge for the testing of non defective uni
56. l non blocking on Full Duplex ports which provides for a PAUSE packet to be transmitted to the sender when the packet buffer is nearly filled and there is danger of lost packets The transmitting device is commanded to stop transmitting into the 6K25 Switch port for sufficient time to let the Switch reduce the buffer space used When the available free buffer queue increases the Switch will send a RESUME packet to tell the transmitter to start sending the packets Of course the transmitting device must also support the 802 3x flow control standard in order to communicate properly during normal operation Note When in Half Duplex mode the 6K25 Switch implements a back pressure algorithm on 10 100 Mb ports for flow control That is the switch prevents frames from entering the device by forcing a collision indication on the half duplex ports that are receiving This temporary collision delay allows the available buffer space to improve as the switch catches up with the traffic flow 38 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 4 6 Power Budget Calculations for Magnum 6K25 PM s with Fiber Media Receiver Sensitivity and Transmitter Power are the parameters necessary to compute the power budget To calculate the power budget of different fiber media installations using Magnum products the following equations should be used OPB Optical Power Budget P min Pp min where P Transmitter Outpu
57. ld the 6KM BLNK in place 6 0 TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments The installation of a Magnum 6K25 Switch is a straightforward procedure see INSTALLATION Section 2 6 the operation is also straightforward and is discussed in Section 4 Should problems develop during installation or operation this section is intended to help locate identify and correct these types of problems Please follow the suggestions listed below prior to contacting your supplier However if you are unsure of www GarrettCom com E 52 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 the procedures described in this section or if the Magnum 6K25 Switch is not performing as expected do not attempt to repair the unit instead contact your supplier for assistance or contact GarrettCom Customer Support 6 1 k 6 2 Before Calling for Assistance If difficulty is encountered when installing or operating the unit refer back to the Installation Section of the applicable chapter of this manual Also check to make sure that the various components of the network are interoperable Check the cables and connectors to ensure that they have been properly connected and the cables wires have not been crimped or in some way impaired during installation About 90 of network downtime can be attributed to wiring and connector problems
58. lease check the ordering information Sec 1 2 for all the various PI6K PoE modules option The LEDs on 6KP8 RJ45 PoE module are slightly different compared to regular non PoE RJ 45 modules as shown in Fig 2 When the PoE port is in use the PoE LED is ON when connected properly to a 803 af compliant PD device on that port When non PoE devices are connected the PoE LED is OFF Operation of Ethernet data traffic is not affected by PoE LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK ACT as shown in the diagram 2 2 5 New PoE Power Pass through model P6KP8 RJ45 MDIX 10 100Mb 8 port The PoE Power pass through RJ 45 ports act similar to regular RJ 45 ports except they have capability of providing power on each port to power up the PD devices 6KP8 45R per the IEEE802 3af PoE standard The Power Pass through PoE modules are totally dependent upon the powerful 48VDC input power supply to support more RJ 45 10 100 ports Each port requires atleast 15watts to power up the PoE PD devices Maxm one PoE modules can be configured in the A B or C slot of any 6K s with 48vdc power input The PoE modules are also available with mix n match with fiber modules Please check the ordering information 12 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Sec 1 2 for all the various P6K PoE modules option The LEDs on 6KP8 RJ45 PoE module are slightly
59. n condition or by the failure of the power supply inside of the Magnum 6K25 Switch Useful info about Alarm contacts 1 There is four terminal block 1 2 3 4 provided next to AC DC power supply 2 The top two pins 1 2 are software operated 3 The bottom two pins 3 4 are hardware operated 4 By default it is NC normally closed 5 The software operation need to be enable and set to get the Alarm traps For detail information about the Software Alarm and software control of SNMP alarm traps please reference the Magnum MNS 6K Software User Manual Chapter 19th 3 5 6K25 Port Module 6KPM Installation The Magnum 6K25 Switches are normally received from the factory with all www GarrettCom com E 27 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 required 6KPM modules installed There may be situations where 6KPM cards need to be added or replaced In cases where additional 6KPM cards are needed the faceplate for an available front mounted slot must be removed The following procedure describes this operation 3 5 1 Preparation for Installing and Removing 6KPMs STOP Be sure the power cord and connections for all powers single or dual is unplugged from the chassis before attempting to remove and or replace any PM cards Failure to do so may result in damage to the unit and will void the warranty Caution Avoid Static Discharge The port modules like most electronic equipment are se
60. ning Tree Protocol RSTP Web based multi level QoS Port and tag based VLANs GVRP IGMP Snooping SNMPc GUI support Event Log SNTP client for time of day BootP and DHCP client for IP configuring and password security Supplied and updated via Internet and GCI FTP Server E RJ 45 ports are MDI MDIX supported The RJ 45 modules are equipped with MDI MDIX capability to eliminate the use of cross over cable The Auto MDIX capability allow the Magnum 6K25 to cascade any Hub switches or media converters with normal straight cable 18 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 2 4 Applications Magnum 6K25 Fiber Switches offer high performance and modularity They provide the flexibility of 1OOMbps fiber and copper ports as well as Gigabit ports with industry standard LAN management software Magnum 6K25 Switches are easily used in a variety of applications including MANs metropolitan area networks client server computing secure VLAN performance upgrades to departmental networks and LAN traffic centers require Gb backbone services The performance characteristic of the 6K25 Switches enables them to inter connect a series of subnets one subnet per 6K25 Switch port in a LAN traffic center The subnet connections may be via fiber or twisted pair cabling 100Mbps or 10 Mbps speed and full or half duplex mode The mixed media capability is ideal for upgrading existing Ethernet LAN networks where existing cabling
61. nit to operate whenever DC power is correctly applied to either or both of the two inputs C4 0 FEATURES AND BENEFITS OF THE DUAL SOURCE DESIGN a The Switch unit can receive power from either input A or B The hub will normally draw its power from the DC source with the highest voltage at a given time b The Switch unit will not allow power to flow from a higher voltage input to a lower voltage input i e the two DC power sources are not mixed together by the hub c When one correct DC input is present the Switch will receive power if the other DC input is absent or even if it is connected with reverse polarity or shorted or grounded d Reverse polarity connections if they should accidentally occur on either input will not damage the Switch or power supply internally nor will it blow the fuse in the internal power supply because of the blocking action of the diodes This is true even if one input connection is reversed while the Switch is operating from the other source e The Switch will not receive power and will not work when both inputs are simultaneously absent or are both incorrectly connected C5 0 INSTALLATION This section describes the proper connection of the 48VDC 24VDC and 125VDC dual source leads to the 48 VDC 24VDC 7 125VDC power terminal block on the Magnum 6Ks Switch shown in Figure The 48VDC terminal block on the Magnum 6K25 Switch as shown in Fig C5 0 is located on the right rear of the unit
62. nsitive to static discharge Use proper ESD measures when handling port modules Step 1 Make sure the 6KPM Card package has all necessary accessories to install it properly Each 6KPM Card package except the Gigabit for field installation contains Daughterboard Bigger and Granddaughter board smaller three 5 8 stand offs for Granddaughter board six 4 40 Pan Head screws along with Front panel face plate package The Front panel faceplate package includes 3 retainer brackets and six 2 56 flat head screws NOTE Every 6KPM Card package comes with their matching Daughter and Granddaughter board The copper 6KPM card should not work properly if mixed with other Fiber combo 6KPM card packages Always install the PM module separately one by one to avoid the mixing Step 2 Remove Chassis Cover The Magnum 6K25 chassis are combined with top and bottom parts and assembled together with the help of 22 Philips head screws There are 7 screws located on the front bottom and rear top of the unit and four screws each on the sides Remove these screws Once these are removed the top cover is easily lifted off the chassis base When the chassis top cover has been removed the interior of the unit is exposed Figure 3 5 la Removing Chassis Cover www GarrettCom com E 28 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Caution Be careful not to disturb the power supply Looking down into the Magnum 6K25 unit
63. o that described in the 48 VDC information above C5 1 UL Requirements The following must be adhered to in order to conform to UL requirements Minimum 18 AWG cable for connection to a Centralized DC power source Minimum 14 AWG cable for connection to earthing wiring Use only with Listed 10 A circuit breaker provided in building installation Complies with FDA radiation performance standards 21 CFR subchapter J or equivalent Fastening torque of the lugs on the terminal block 9 inch pound max 6 Centralized DC Power Source cable securement use at least four cable ties to secure the cable to the rack at least 4 inches apart with the first one located within 6 inches of the terminal block ile oe i C6 0 ORDERING INFORMATION To order the optional Dual Source 48VDC power supply factory installed order Dual Src48V as a separate line item following the product model Example Magnum 6K25R 48VDC Dual Src 48V for the regular DS model with no ON OFF switch or Dual Src48V SWITCH with the ON OFF manual switch Similarly order the Dual source 24VDC or Dual source 125VDC as a separate line item following the product model Example Magnum 6K25R 24VDC or Magnum 6K25R 125VDC Dual Sre24V for regular models with no ON OFF switch Or Dual Src125V Switch for models with the ON OFF switch C7 0 OPERATION Operation of the Dual Source Magnum 6Ks 48VDC 24VDC and 125VDC Switch models are identical to that of the
64. ode FX ST twist lock Module The Magnum 6KP4 3 FLSTFX is a combo fiber module with two 1OMb 6KP4 RJIOMST 2 TX GLK RX two 100Mb multi mode fiber module and in combine 4 ST Fiber ports All four fiber ports are ST connectors and configured as 1OMb Half duplex by default for 10Mb fiber and 100Mb Full duplex for the 1OOMb fiber The 1OMb ST fiber ports allow the user to connect their legacy 1OMb network to the Magnum 6K25 switch They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports Whereas the 1OOMb ST module allow to connect the 100Mb demand of Switch devices It supports distances according to the 10Base FL standard i e 2Km distance for multi mode fiber Single mode for 10Km distance may be available as a special order Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and FDX HDX LED indicating full duplex mode when lit or half duplex if off 5 2 2 6KP6 RJMSC 4 10 100Mbps RJ 45 and 2 100Mb multi mode FX SC snap in Fiber connector The Magnum 6KP6 6KP6 RJMSC RJMSC is also a Combo 6 Port 4 Port 10 100Mbps and 2 100 Mb SC Fiber Port module equipped with 4 10 100Mb RJ 45 ports along with 2 multi mode 100Mbps fiber optic transceivers all in one module This is Similar to the 6K6 RJMST It has the same LEDs indicating port activity ACT Link
65. of this manual for more details Use an RFQ for other variations 3 4 1 Alarm Contacts for monitoring internal power and Software Traps The Alarm Contacts feature optional on Magnum 6K25 s provides two Form C Normally Closed NC contacts to which the user can attach two sets of status monitoring wires at the green terminal block When this option is present the terminal block for Alarm Contacts is part of the Power Input panel in the Magnum 6K25 case The AC or DC power input connection is in the same panel A manual On Off Switch for power to the unit is not available on 6K25 units with the Alarm Contacts option as these two features occupy the same space in the case The first NC Alarm Contact top position is a Software Alarm operated by user settings in the MNS 6K software The user can disable the Software Alarm feature with a software configuration command if desired When the Software Alarm is enabled the Form C Normally Closed NC contact is held close during normal software operation A user defined software malfunction such as an SNMP Trap or a Software Security violation or an S Ring Fault causes the contact to open and thus trigger an alarm in the user s monitoring system The second bottom position NC Alarm Contact is held close when there is power on the main board inside of the 6K25 This provides a Hardware Alarm because the NC contacts will open when internal power is lost either from an external power dow
66. ons and brackets Section 3 3 Rev C 06 02 Updated the port settings configuration at sec 4 3 added Magnum 6K25 s MNS Software manual access information at sec 2 2 9 Rev B 04 02 Updated the Rack mounting 48V DC options and Appendix B and C with 24VDC and 125VDC Power Supply option Rev A 12 01 This rev is the initial release of the 6K25 manual Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 The Magnum Line INDUSTRIAL NETWORKING PRODUCTS DESIG NED AND MANUFACTURED IN THE USA OVERVIEW GarrettCom Inc offers the premium quality Magnum line of INDUSTRIAL conectivity products with industry standard functionality and built in fiber configurability Magnum products are designed for use in demanding Industrial Grade Carrier Class POWER UTILITY and OEM applications where reliability is a primary consideration 6K Series Managed Field Switches Gigabit 100 and 10 Mbps fiber and copper ports mix and match Features SFF fiber and DC power in 1U units DX Series Serial Device Routers Ethernet and Serial 4K Series Switches 100 and 10 Mbps copper ports with optional fiber port with auto negotiating full switching performance Quad Series Fiber Switches 100 amp 10Mbps fiber and copper ports mixed speed and mixed media types full switching performance mP62 and P62F Outdoor Ethernet SwitchES for temperature uncontrolled locations 6 10 100 and 2 100Mb fiber ports can be connected in strings M
67. oo GarrettGom Industrial Networking at Its Best Magnum 6K25 Managed Fiber Switch Hardware Installation and User Guide _ ww GarrettCom com 5 00 USD Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Magnum 6K25 Managed Fiber Switch Hardware Installation and User Guide Part 84 00123 Rev D Trademarks Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Underwriters Laboratories GarrettCom Magnum and Personal Switch are trademarks and Personal Hub is a registered trademark of GarrettCom Inc Important The Magnum 6K25 Managed Fiber Switch contains no user serviceable parts Attempted service by unauthorized personnel shall render all warranties null and void If problems are experienced with Magnum 6K25 Switch products consult Section 6 Troubleshooting of this User Guide Copyright 2006 GarrettCom Inc All rights reserved No part of this publication may be reproduced without prior written permission from GarrettCom Inc Printed in the United States of America www GarettCom com E 1 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Contacting GarrettCom Inc Please use the mailing address phone and fax numbers and email address listed below GarrettCom Inc 47523 Westinghouse Dr Fremont CA 94539 7437 Phone 510 438 9071 Fax 510 438 9072 W
68. opening in a Magnum 6K25 or 6K25R chassis CONSOLE CBL Industry standard serial cable DB 9 connectors for RS 232 null modem connection sometimes called an Xmodem cable used to connect a PC or a character terminal to the Management port CONSOLE USB Console attachment cable serial to USB cable with one DB9 for the managed Switch and a USB interface for the USB connector to a PC 6K PoE Modules with 48VDC Pass Through Configuration options only one A B or C module slot of 6K Series switch with 48VDC power input may be configured with a PoE Modules New P6KP8 RJ45 8 port PoE module for 6ks with 48vdc PS w eight PoE power source 10 100 auto negotiating auto cross RJ 45 ports New P6KP8 45RJ 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 10 100 auto negotiating auto cross RJ 45 ports New P6KP8 45MT 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 2km mm FX MTRJ connectors New P6KP8 45MLC 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 2km mm FX LC connectors New P6KP8 45SLC 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 15km sm FX LC connectors New P6KP8 45 2MT 6 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two normal RJ 45 10 100 ports twol00 Mb 2km mm FX MTRJ connectors New P6KP8 452SLC 6 2 port PoE module for 6ks with 48vdc PS
69. parent to an observer Another feature implemented in Magnum 6K25 Switches is a collision based flow control mechanism when operating at half duplex only When the Switch detects that its free buffer queue space is low the Switch prevents more frames from entering by forcing a collision signal on all receiving half duplex ports in order to stop incoming traffic 2 2 11 Managed Network Software MNS 6K for Magnum 6K25 Series Magnum 6K25 Series s come with licensed MNS 6K Firmware Rel 3 2 which allows to configure the Magnum 6Ks as a Managed Switch and other Software enabled features For additional information about MNS 6K see the Magnum 6K25 Series MNS Software User guide in pdf format a separate document normally accessed via your web browser at ftp ftp garrettcom com or FTP client program by fip GarrettCom com using user m6kuser password m6kuser All MNS 6K software information including new releases and upgrades related to MNS 6K software can be accessed and download from GarrettCom s FTP site Alternatively for documentation and latest information or needed GarrettCom proprietary MIBs for SNMP www GarrettCom com E 16 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 www GarrettCom com techsupport index htm software and look for Magnum MNS O6K info Magnum MNS 6K Operator Training This interactive training software allow the basic and advanced info about the Magnum
70. r CAT 5E or better 100 ohm UTP or shielded twisted pair STP balanced cable The CAT 5E or better 100 ohm UTP or shielded twisted pair STP balanced cable is recommended to use when making OOOBASE TX connections In either case the maximum distance for unshielded twisted pair cabling is 100 meters 328 ft See Section 4 3 for manual Up Link switch on port 1 of copper port modules Media IEEE Standard Connector Twisted Pair CAT 5E 1000BASE T RJ 45 NOTE Itis recommended that high quality CAT 5E cables which work for both 100 Mb and 1000Mb be used whenever possible in order to provide flexibility in a mixed speed network The following procedure describes how to connect a LOOOBASE T twisted pair segment to the RJ 45 port The procedure is the same for both unshielded and shielded twisted pair cables 1 1000Base T connections require that all four pairs or wires be connected Insert either end of the cable with an RJ 45 plug into the RJ 45 connector of the port Note that even though the connector is shielded either unshielded or shielded cables and wiring may be used 2 Connect the other end of the cable to the corresponding device 3 Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established 3 3 Table Top or Shelf Mounting The Magnum 6K25 Manageable Switches can be easily mounted on a table top or any suitable horizontal surface and has four r
71. racket mounting holes in the sides of the Magnum 6K25 permits it to be mounted in various ways The same holes fit all three types 19 ETSI 23 of brackets The mounting for the 23 is illustrated in Figure 3 3 1 below The brackets may be attached flush with the front or attached in the center for a set back mounting which may reduce cabling torque The optional 23 brackets and the ETSI 21 brackets each come as a pair in a package along with the necessary screws for attaching the brackets to the sides of the Magnum Switch unit They must be ordered as line items www GarrettCom com E 25 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 3 3 2 Rack mounting Reverse version of the Magnum 6K25s The optional Reverse Magnum 6K25 Model has all of the cabling Ethernet cabling power cabling and console port cabling connectors in the rear and the status LEDs in the front The status LEDs that are co incident with the ports are still present there and a second or dual set of LEDs are used for status visibility in the front of the unit showing the same data There are three options of brackets available to mount in the standard 19 frame or the 23 frame or ETSI 21 frame The 19 brackets are included with each unit the other two may be purchased if desired With each bracket type there are three different mounting options is shown in Fig 3 3 2 The case of the Magnum 6K25 has mounting
72. re to use single mode fiber port connectors Single mode fiber cable has a smaller diameter than multi mode fiber cable 9 125 microns for single mode 50 125 or 62 5 125 microns for multi mode where xx xx are the diameters of the core and the core plus the cladding respectively Single mode fiber allows full bandwidth at longer distances and may be used to connect 10 Mb nodes up to 10 Km apart or 18Km with the 6K SSC The same procedures as for multi mode fiber applies to single mode fiber connectors Follow the steps listed in Section 3 2 2 above 3 2 4 Connecting Twisted Pair RJ 45 CAT3 CAT5 Unshielded or Shielded The RJ 45 ports of the Magnum 6K25 can be connected to the following two media types 100BASE TX and LOBASE T CAT 5 cables should be used when making 100BASE TX connections When the ports are used as IOBASE T ports CAT 3 may be used In either case the maximum distance for unshielded twisted pair cabling is 100 meters 328 ft Media IEEE Standard Connector Twisted Pair CAT 3 4 5 1OBASE T RJ 45 Twisted Pair CAT 5 1OOBASE TX RJ 45 NOTE Itis recommended that high quality CAT 5 cables which work for both 10 Mb and 100Mb be used whenever possible in order to provide flexibility in a mixed speed network since dual speed ports are auto sensing for either 10 and 1OOMD s The following procedure describes how to connect a LOBASE T or 1OOBASE TX twisted pair segment to the RJ 45 port The procedure is the same for
73. romised earthing path 6 24vdc 48vdc and 125vdc must be installed in restricted access locations 7 CB Circuit breakers of 10Amps should be shown on top of the Rack This section describes installation of the Magnum 6K25 Switches as well as connection of the various Ethernet media types 3 1 Locating Magnum 6K25 Switches The location of a Magnum 6K25 Switch is dependent on the physical layout of the network Typically the Switch is placed in a central wiring location where groups of network devices need to be connected in order to communicate with each other These Switches are typically rack mounted in a wiring closet see Section 3 3 2 below but because they have rubber feet they can also be installed on a shelf or table top unit The compact size allows it to be easily placed in an office or lab area and it can also be either shelf of wall mounted see Section 3 3 1 below Locate an AC receptacle that is within six feet whole hgh ot amit 2 meters of the intended Magnum 6K25 site The ii i T i ii aa E ed ee i y rugged metal case of the Magnum 6K25 will normally hay Fs protect it from accidental damage in a lab or workplace 7 setting Maintain an open view of the front to visually monitor the status LEDs Keep an open area around the unit so that cooling can occur from the small fan on the left side while the unit is in operation See figure below Figure 3 1 Location of the Magnum 6K25 s cooling
74. ructions with illustrations Remove the 6K25 PM s from the shipping container Be sure to keep the shipping container should you need to ship any of the PMs separately at a later date In the event there are items missing or damaged contact your www GarrettCom com E 40 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 supplier If you need to return the unit use the original shipping container if possible Refer to Chapter 5 for specific return procedures 5 2 6KPM Module Description An important feature of the Magnum 6K25 is the use of Port Modules for flexible mixed media connectivity to RJ 45 and fiber media Since the Magnum 6K25 Switches have dual speed capability for copper ports the 6 or 8 port interfaces are designed to support all standard Ethernet media types at 10 or 1OOMps speed Each 6K25 PM provides six or eight ports for connecting Ethernet segments with its individual connector type and media For a list of 6K25 Port Module types refer to Section 1 2 Each 6K25 PM is individually described in the following sections NOTE The port 1 on the RJ 45 ports on all the modules either all RJ 45 ports or used for COMBO module is set as other user ports 5 2 1 6KP6 RJMST 4 10 100Mbps RJ 45 and 2 100Mb multi mode FX ST twist lock Combo Module The Magnum 6KP6 RJMST is a combo 6 port module of RJ 45 s at 10 100Mbps and fiber optic ports at 100MB The Combo module is equipped with dual
75. s Designed for use in network traffic centers the Magnum 6K25 Managed Fiber Switches are easy to install and use Addresses of attached nodes are automatically learned maintained and aged out adapting the switching services to network changes LEDs provide status information on each port The Magnum 6K25 provides high performance plug and play hardware operation 802 1p packet prioritization in hardware and industry standard managed networks software functionality all in convenient 1U rack mount packages 2 2 1 Magnum 6K25 and 6K25R chassis The Magnum 6K25 is a 19 rack mountable Ethernet Switch with three eight port slots A B and C and one Gb only slot D for configuration flexibility Slots A B and C may be configured with any of a large selection of fiber and copper port types and combinations of types typically eight ports per module but sometimes 6 or 4 ports or even one Gb port Slot D may be configured with a Gb module that accepts GBICs The port types configurable using the 4 slots allows the 6K25 to efficiently serve a large variety of applications especially using fiber media The Magnum 6K25 port modules are normally factory installed but may be changed or added in the field See Section 5 Magnum 6K25 Figure 2 2 la Regular 6K25 front view configured for 24 1 Gb ports Status LEDs are part of each port module and are viewable when connecting the Ethernet media A regular rack mount 6K25 is sho
76. s the performance of large Ethernet LANs typically serving as a backbone switch It has the flexibility to handle a mix of both fiber and twisted pair switched ports along with Gigabit backbone port options Industry standard IEEE 802 1p QOS prioritization is included providing high performance switching services for both smooth streaming and bursty data traffic The Magnum 6K25 has up to 25 ports capacity all of which may be configured as fiber ports but still offers a space saving rack mount chassis that is only 1U 1 70in or 4 32cm high The mixed media capability allows user selection of all popular flavors of fiber port connectors and modes including even 10Mb fiber along with Gigabit ports It also allows a mix of 10 100Mb RJ 45 copper ports and a fiber Gigabit port in the same unit This flexibility is achieved via a family of 6K25 port modules for copper and fiber built in emphasizing Small Form Factor fiber for high fiber port density 6 port modules for fiber and RJ 45 combinations and 1Gb port module selections using GBICs These modules can be factory configured in a base chassis unit or may be changed in the field by trained technicians to adapt the unit to the user s application and Ethernet cabling requirements Even evolving mixed media requirements for 10Mb and 100Mb fiber and copper as well as Gigabit ports can be handled by the Magnum 6K25 product The 6K25 managed switches also provides PoE op
77. sentially the same as the ST and SC types It has the same LEDs per port indicating port activity ACT Link LK and FDX or HDX operation 5 2 5a 6KP6 MTI0ST 4 100Mb multi mode FX MTRJ Small Form Factor and 2 10Mb Multi mode ST Fiber port The 6KP6 RJ1OST is a combo module with two different kinds of fiber flavor with two different speeds The top four ports of MTRJ Small form factor fiber support at 100Mb full duplex whereas the bottom two ports multi mode ST Fiber support 1OMb half duplex This combo module provides more flexibility to the user to connect their legacy 10Mb fiber as well as 100Mb to the Magnum 6K25 Switch When installed in a Magnum 6K25 Switch the 100Mb MTRJ connector supports fiber optic cable distances up to the IEEE standard 100Mbps distance limits 1 e typically 2km at full duplex and 412m at half duplex The 1OMb Multi mode ST Fiber connector supports the standard fiber optic distance limit of 2Km at Full and Half duplex both The functionality of this IOOBASE FX multi mode 4 port module is essentially the same as the ST and SC types It has the same LEDs per port indicating port activity ACT Link LK and FDX or HDX operation 5 2 6 6KP8 45MT 4 10 100Mbps RJ 45 and 4 100Mb multi mode FX MTRJ Small Form Factor The Magnum 6KP8 45MT 6KP8 45MT 4 Port 10 100Mbps amp 4 port 100Mbps Multi Mode ZO Module is a combo module with copper and fiber Small Form Factor MTRJ type ports The
78. small size of MTRJ connectors give an advantage of placing more ports on one module The 6KP8 45MT is equipped with 4 10 100 RJ 45 ports and 4 MTRJ fiber 2 6 8 E 3 activity 4 FULL MALF www GarrettCom com E 46 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 When installed in a Magnum 6K25 Switch it supports the standard distances as mentioned on 5 2 3 and the LEDs also 8 Port 100Mbps multi mode LC fiber port act similarly 5 2 7 6KP8 MLC 8 ports 100Mbps multi mode LC connector Small Form Factor Magnum 6KP8 MLC is a C4 activity 2 FULL HALF eight port multi mode fiber LC LINK connector small form factor used primarily in 100Mbps fiber to the desktop links When installed in a Magnum 6K25 Switch it supports fiber optic cable distances up to the IEEE standard 100Mbps distance limits 1 e typically 2km at full duplex and 412m at half duplex The compact size of the LC Connector reduces the size of wiring panels in wiring closets while providing the advantage of future proof fiber optic technology The cable end is a plug in connector with both fiber strands terminated in one housing that cannot be improperly inserted Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off 5 2 8 6KP8 45LC
79. standard models 60
80. t 88 150 VDC With the exception of the dual DC input power connections and the power supply all specifications and configuration options for the Magnum 6K25 48VDC 24VDC and 125VDC models with this Dual Source option are identical to those listed in the Magnum 6K25 Fiber Switches Installation and User Guide including Appendix B Internal DC Power Supply Option C2 0 MAGNUM 6K25 with 48VDC 24VDC and 125VDC Dual Source option The 6K25 Switch models with the internal 48V DC 24VDC and 125VDC Dual Source power supply are designed for installations where a battery plant is the power source and where two separate power sources are utilized in order to increase operational uptime and to simplify maintenance www GarrettCom com E 58 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 The functionality of the Magnum 6K25 Switch 48VDC 24VDC and 125VDC Dual Source Option units is identical to the standard AC powered models Refer to the main sections of this Installation and User Guide for a detailed description of the Magnum 6K25 Switches C3 0 DUAL SOURCE OPTION THEORY OF OPERATION The Dual Source DC power option is designed using diodes inside of the chassis on each DC power input A line A diode is placed in each of the B four input lines behind the four B external power connection terminals a CHASSIS so that power from an external source can only flow into the unit This allows the u
81. t Power and Pg Receiver Sensitivity Worst case OPB OPB 1dB for LED aging 1dB for insertion loss Worst case distance Worst case OPB in dB Cable Loss in dB Km where the Cable Loss for 62 5 125 and 50 125um M m is 2 8 dB km and the Cable Loss for 100 140 Multi mode is 3 3 dB km and the Cable Loss for 9 125 Single mode is 0 5 dB km and the Cable Loss for 9 125 Single mode is 0 4 dB km LXSC25 and the Cable Loss for 9 125 Single mode is 0 25 dB km LXSC40 and the Cable Loss for 9 125 Single mode is 0 2 dB km LXSC70 The following data has been collected from component manufacturer s Agilent s and Lucent web sites and catalogs to provide guidance to network designers and installers Fiber Speed Port Mode Module Std 6KP4 10Mb Multi F10ST FL Mode 6KPM 100Mb Multi 2 1309 20 MST MSC FX mode 0 4 293 100Mb Single 18 6KPM SSC py mode 0 4 1300 9 125 15 100Mb Single 40 6KPM FX mode 0 4 1300 9 125 5 SSCL 6KpM 100Mb Multi 2 1399 62 5 125 20 MTRJ FX mode 0 4 50 125 23 5 2 6KPM 100Mb Multi 0 4 1300 62 5 125 19 MLC FX mode 5 6KPM SLC 190Mb Single 1310 9 125 15 a 2 2 P LE Qo or ps 0 55 GBIC 1000Mb Multi 1300 62 5 125 9 5 SXSC mode 50 125 10 GBIC 1000Mb Single 1300 9 125 9 5 LXSC10 mode 39 Magnum
82. tand off female provided at the front of the 6K25 Main Board and screw down tightly with the three 5 16 stand off male on the top of the Granddaughter board The 5 16 stand off has been used to place the daughter board on the top of the granddaughter board and latch it securely Te beoo geile raogoorHa Fig 3 5 2a Granddaughter Board shown separately Fig 3 5 2b Granddaughter Board placed in slot A and secured with three 7 16 stand off s Step 3 The figure here illustrates the basic layout of an individual PM card Each 6KPM card fits into the space provided on the main board Fig 3 5 2c Daughter Board top view of version for 4 copper 10 100 ports Port 1 Can be configured as uplink x crossed ports for cascading as shown in the Fig 30 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Fig 3 5 2d Daughter Board shown upside down with two male latch connectors Step 4 Hold the daughter board with both hands at the end and align the two cream color latching connectors male placed at the bottom of the daughter board with the other female connector placed on the Granddaughter and main board As shown below in Fig 3 5 2e Fig 3 5 2e Magnum 6KPM daughter board aligned with the bottom female connector for the installation Step 5 Once the latching connectors are aligned properly and the mounting holes are aligned with stand offs then press slowly and firmly with two
83. ted but may be changed in the field Rack mounting may be standard or reverse 19 inch or ETSI or 23 Telco The standard rack mounting provides Ethernet ports and status LEDs in front service connections power input and management console in the rear Reverse rack mounting provides status LEDs in front and all cabling connections in the rear Standard 19 rack mount brackets are included with ETSI and 23 Telco optional Standard AC power input 48VDC or 24VDC or 125VDC input is optional Standard AC power input is IEC plug auto ranging for worldwide use For special applications models with 48 VDC or 24VDC or 125VDC are available Dual Source DC input can also be selected and configured on the DC power input models Heavy duty design for Industrial Ethernet and extended temperature operation Fiber ports take more power than copper ports but the Magnum 6K25 design provides for this with heavy duty components The ambient temperature can be up to 55 C www GarrettCom com E 17 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 E NEBS and ETSI tested and certified The 6K25 has been tested and certified for NEBS and ETSI Request test reports E MNS 6K licensed Network Management Software included S Ring optional Release 2 3 summer 03 includes SNMP Switch Management with secure access control RMON CLI Port Security Port Mirroring Port Settings Control Telnet TFTP FTP support Span
84. tion via Power pass through and power inside PoE modules and allows the users to select a wide option of combo PoE modules to support 802 3af pd devices See details in sec 5 2 10 and 5 2 11 The Power Sourcing Equipment PSE and are fully compatible with Powered Devices PD e g wireless access points IP phones that comply with the IEEE 802 3af PoE standard The PoE switch ports have an auto sensing algorithm so that they provide power only to 802 3af PoE end devices PoE is managed by a multi stage handshake to protect equipment from damage and to manage power budgets The PoE ports will discontinue supplying power when the PoE powered devices are disconnected and support the 802 3af PoE PSE standard for over current protection under current detection and fault protection The packaging and power input options target the Magnum 6K25 at heavy duty applications The chassis mounting rack style may be regular with the ports and LEDs in the front and the power input and management console connector in the rear or www GarrettCom com E 8 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Reverse with the ports and LEDs and the power input and the management console connector all in the rear and a duplicate set of LEDs in the front Rack widths accommodated include standard 19 RETMA ETSI and 23 Telco Input power may be AC or 48VDC for Telco environments or 24VDC for Industrial application
85. to regular non PoE RJ 45 modules as shown in Fig 2 When the PoE port is in use the PoE LED is ON when connected properly to a 803 af compliant PD device on that port When non PoE devices are connected the PoE LED is OFF Operation of Ethernet data traffic is not affected by PoE LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK ACT as shown in the diagram PoE LEDs Summary 5 2 12 For PoE devices each RJ 45 PoE port supports only 802 3af complaint devices The PoE LED is ON when the attached PD is drawing power from the port For non PoE devices connected the PoE port will act as a normal RJ 45 port and the PoE LED is OFF No power is being sent out from the port The PoE ports in Magnum 6K s with 48VDC power input act as a pass through so the 48VDC power source must be strong enough to provide power to the 6K switch and to all the 8 RJ 45 ports with PD devices connected up to 15 watts per PoE port In the case where the 48 VDC power in not internally connected and no power is coming to the PoE ports for some reason all the PoE port LEDs are ON simultaneously to indicate a trouble condition The ports will still operate properly for data traffic 6KP8 45 2MT 6 10 100Mbps RJ 45 and 2 100Mb multi mode FX MTRJ Small Form Factor 50 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 The Magnum 6KP8 6KP86KP3MT 45 2MT eight port Module is a 6 Port 10 10M
86. to ranging Power Consumption 55 watts typical 60 watts max for a fully loaded fiber model 35 watts for a fully loaded copper only model DC Power Supply Options 48VDC Power Input Voltage 36 to 70 VDC 24VDC Power Input Voltage 20 to 40 VDC 125VDC Power Input Voltage 88 to 300VDC Std Terminal Block GND Power Consumption same as for AC models see above www GarrettCom com E 2 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 For DC internal power supplies at 48VDC 24VDC and 125VDC including Dual Source options for continuity of operation when either of the DC input sources are interrupted see Appendices B and C Per port MDI or MDIX on RJ 45 The copper daughter board has MDI MDIX Auto crossover on all the RJ 45 ports and eliminate the use of cross over cable between the devices Also port specific user settings such as FDX or HDX copper 10 100 speed can be fixed using software commands Alarm Contact Optional Alarm Contact option is offered as a configuration option The two alarm contacts are SPST NC Form C relays and an open condition indicates abnormal status The Hardware Alarm monitors internal power on the main board and the Software Alarm is activated by one or more user selected software traps Agency Approvals UL listed UL60950 cUL CE Emissions meet FCC Part 15 Class A NEBS Level 3 and ETSI Certified for Carrier Central Offices IEEE 1613 Class 2
87. ts under warranty Testing and repair of product that is not under warranty will result in a customer user charge 6 4 Shipping and Packaging Information Should you need to ship the unit back to GarrettCom please follow these instructions 1 Package the unit carefully It is recommended that you use the original container if available Units should be wrapped in a bubble wrap plastic sheet or bag for shipping protection You may retain all connectors and this Installation Guide CAUTION Do not pack the unit in Styrofoam popcorn type packing material This material may cause electro static shock damage to the unit 2 Clearly mark the Return Material Authorization RMA number on the outside of the shipping container 3 GarrettCom is not responsible for your return shipping charges www GarrettCom com E 54 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 4 Ship the package to GarrettCom Inc 47823 Westinghouse Dr Fremont CA 94539 7437 Attn Customer Service APPENDIX A WARRANTY INFORMATION GarrettCom Inc warrants its products to be free from defects in materials and workmanship for a period of three 3 years from the date of shipment by GarrettCom During this warranty period GarrettCom will repair or at its option replace components in the products that prove to be defective at no charge other than shipping and handling provided that the product is returned pre paid to GarrettCom
88. ubber feet to provide stability without scratching finished surfaces agnum Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 3 3 1 Rack mounting for 19 RETMA racks regular Magnum 6K25s Installation of a Magnum 6K25 Fiber Switch in a 19 rack is a simple procedure The units are 1U 1 70 high When properly installed the front mounted LED status indicators should be in plain view and easy to read Rack mount installation requires special 19 rack mounted brackets and screws included with each Magnum 6K25 unit These brackets attach to the front sides of the Switch regular package 1 e not the Reverse version which is then typically fastened into a standard 19 RETMA rack as shown here The 23 brackets and the ETSI European metric approx 21 brackets are also available optional for rack mounting of Magnum 6K25 Switches These brackets are popular in the Telco industry where they are a standard for Central Office rack mounting purposes The 23 and the ETSI brackets are mainly used for larger equipment sale Ae K Standard Flush 23 Mount Bracket A 3 Mid Range Mount or a is Pl ia o j 10 1 L 5 Set Back Bracket 00 E Fig 3 3 1 Mountings for Magnum 6K25 units rack mounted in a frame assemblies in rack mounting frames where the rack mount equipment is typically accessed in operation from both sides The b
89. uipped with VLAN RMON SNTP and other standard managed LAN features to provide a secure and stable network The 6K25 Managed Fiber Switch with mixed media flexibility allows the users more than one configuration alternative The user has an advantage by fulfilling the present requirements as well as benefiting from the multiple choices of modules to support future expansion as the network evolves The Gigabit port option boosts the bandwidth for high speed to support the peak traffic and minimize congestion 20 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 3 0 Installation Before installing the equipment it is necessary to take the following precautions 1 If the equipment is mounted in an enclosed or multiple rack assembly the environmental temperature around the equipment must be less than or equal to 500 2 If the equipment is mounted in an enclosed or multiple rack assembly adequate airflow must be maintained for proper and safe operation 3 If the equipment is mounted in an enclosed or multiple rack system placement of the equipment must not overload or load unevenly the rack system 4 If the equipment is mounted in an enclosed or multiple rack assembly verify the equipment s power requirements to prevent overloading of the building s electrical circuits 5 If the equipment is mounted in an enclosed or multiple rack assembly verify that the equipment has a reliable and uncomp
90. um 6K s with 48 VDC power input act as a pass through so the 48VDC power source must be strong enough to provide power to the 6K switch and to all the 8 RJ 45 ports with PD devices connected up to 15 watts per PoE port e In the case where the 48VDC power in not internally connected and no power is coming to the PoE ports for some reason all the PoE port LEDs are ON simultaneously to indicate a trouble condition The ports will still operate properly for data traffic 5 2 11 New PoE Power Pass through model P6KP8 RJ45 MDIX 10 100Mb 8 port ww GarrettCom com j 3 3 49 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 The PoE RJ 45 ports act similar to regular RJ 45 ports except they have capability of providing power on each port to power up the PD devices per the TEEE802 3af PoE 6KP8 45 standard The Power 8 Port 10 100Mb Copper ports Pass through PoE modules are totally dependent upon the powerful 48 VDC input power supply to support more RJ 45 10 100 ports Each port require atleast CE p lt 15watts to power up the L T KAK 10 10 PoE PD devices In this om Fig the top 8 RJ45 4 FULL HALF ports are enhanced with POE option The 8 RJ45 POE module are also available with mix n match with fiber modules Please check the ordering information Sec 1 2 for all the various P6K PoE modules option The LEDs on 6KP8 RJ45 PoE module are slightly different compared
91. ut is 48 VDC Same as 6K25 except the power input is 24VDC Same as 6K25R except the power input is 24VDC Same as 6K25 except the power input is 125VDC Magnum 6K25R 125VDC Same as 6K25R except the power input is 125 VDC Configuration Options Each Magnum 6K25 and 6K25R base unit has four port module slots The first three A B C may be one of the modules below one slot D may only be a Gigabit module Select up to four port modules per base unit Magnum 6K25 Port Modules 6KP8 MTRJ 6KP8 MLC 6KP8 SLC 6KP8 RJ45 6KP4 F10ST 6KP4 FXST 6KP4 FLSTFX 6KP8 45MT 6KP8 45LC 6KP8 45 2MT 6KP8 45 2SLC LC connectors 6KP6 RJMST 6KP6 RJMSC 6KP6 RJSSC 6KP6 RJSSCL 6KP6 MT10ST 6KP6 RJ10ST SFF Fiber module w eight 100Mb mm FX MT RJ connectors SFF Fiber module w eight 1OOMbps mm FX LC connectors SFF Fiber module w eight 100Mbps sgl m FX LC connectors TP Module w eight 10 100Mbps auto negotiating RJ 45 ports 2 2 10Mb Fiber module w four 1OMb 2km FL ST connectors 2 2 100Mb Fiber module w four 1OOMb 2km FX ST connectors 2 2 ST Fiber module w two 1OOMb amp two 10Mb ports 2km 4 4 module w four RJ 45 ports and four 2km mm FX MT RJ s 4 4 module w four RJ 45 ports and four 2km mm LC connectors 6 2 module w six RJ 45 ports and two 2km mm MTRJ connectors 6 2 module w six RJ 45 ports and two 1OOMb 15km sgl mode FX 4 2 module w four RJ 45 ports and two 2km mm FX SC s 4
92. ut notice www GarrettCom com E 6 Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 2 0 Introduction 2 1 Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product notify the carrier of any damage that you believe occurred during shipment or delivery Inspect the contents of this package for any signs of damage and ensure that the items listed below are included This package should contain 1 Magnum 6K25 Managed Fiber Switch base unit configured with user selected port module options 1 AC Power Cord U S and other 115 VAC only 1 Set of metal Ears for 19 rack mounting 1 Installation and User Guide this manual 1 Product Registration Card Remove the items from the shipping container Be sure to keep the shipping container should you need to re ship the unit at a later date To validate the product warranty please complete and return the enclosed Product Registration Card to GarrettCom Inc as soon as possible In the event there are items missing or damaged contact the party from whom you purchased the product If the unit needs to be returned please use the original shipping container if possible Refer to Section 6 Troubleshooting for specific return procedures Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 Za Product Description Magnum 6K25 Managed Fiber Switch The Magnum Managed Fiber Switch boost
93. wn in Figure 2 2 1la On Reverse rack mount models there is a duplicate set of LEDs on the other front side Magnum 6K25 Managed Fiber Switch Installation and User Guide 04 06 for normal status viewing from that direction Of course with management the port status data is also available in software 2 2 2 Eight port SFF fiber modules 6K8 MTRJ 6K8 MLC 100Mb fiber Fig 2 2 2 SFF Fiber Port Modules 6K8 MTRJ to the left and 6K8 MLC or SLC below In an eight port SFF fiber port module all of the fiber ports are of the same speed 100Mb mode and connector type Models are available with Small Form Factor SFF are multi mode MT RJ or LC act type connectors and single mode AAAA dh T f ACT LC type connectors zg LZ m Ka o Ka enema The 100Mb fiber eight a ik ii ht y ACT port modules for the Magnum AC mm LK E OLkK 6K25 s normally are set factory default to operate in full duplex mode for best fiber distance and performance Using the 6K25 s MNS software the user may select full or half duplex mode per port through set up of the software See Magnum 6K25 MNS Software Manual for the flexibility to adapt to any FDX or HDX type of Fast Ethernet devices There are three LED s per fiber port The Link LK LED indicates ready for operation on that port when lit the F H LED indicates operation in full duplex mode when ON half duplex when OFF and the blinking

User Guide - GarrettCom

Contents

Download Pdf Manuals

Related Search

Related Contents