88-UP Harley Touring - LegUp by Chopper Design
Contents
1. Every time a bolt passes the light should get bright when the bolt is nearby and off after it passes If this is not happening you may need to get the sensor a bit closer to the bolts SMM 1s a very small distance If you have to move the sensor closer you may have to shim the back of the bracket No matter what you need to do you MUST make sure that as the wheel turns the light works as described above Once you are certain attach the bracket permanently with the 2 sided tapes and test it again If all is perfect you may optionally fasten this more permanently by drilling a hole in the swing arm and attaching a sheet metal screw to keep it in place 1f you choose mine is not screwed on and has held in place for years The automatic retraction of the legs as well as their deployment RELIES on this sensor being placed perfectly Once satisfied with the mount skip down to the wire routing instructions below 24 BIKE WITH NO PULLEY BOLTS CUSH DRIVE With the bike on the lift the rear wheel off the lift and the bike in Neutral remove the bottom bolt from the right shock at the rear of the bike Insert the U shaped bracket with the proximity sensor attached behind the shock and in front of the hole in the swing arm so the bolt will pass though it when reinserted Reinsert the shock bolt and tighten the nut just a bit so the bracket can move freely but snug enough so it stays where you put it y 4 iy A Find the2. We want to slowly install the compressor in the bag The silver valve system goes toward the back and the compressor is slid back as far as it can go It is mounted on rubber feet to avoid damage to the bag and to reduce vibration The picture here shows the compressor plugged in with lines attached NOTE We supply you with some black rubber edging It may be used if after installing the compressor you find the metal edge touches the hard bag somewhere causing a vibration If once the compressor is on you need to cut pieces of the rubber and slide it on the metal where needed to keep the vibration down Once the compressor is in place the air lines should be attached to the fittings you mounted in the saddlebag The right hose closest to the outside of the bag should be attached to the bottom fitting and the left hose should be attached to the top fitting The compressor should feel very stable in its new home Assuming it does this would be a good time to run the big wire into the bag and connect the computer seen left with the label on it to the 12 pin plug and connect the compressor to the 8 pin plug These plugs can only be attached one way and we are going to leave the computer and wires just loose in the bag for now I promise we will make it all pretty before you are done In preparation for testing the system 1f you haven t already hook the negative battery terminal and the lead from our power connection up
3. Long Soft Bags Only 2 1 4 20 X 2 Chrome Allen Bolts w Split Washers HB Bracket 2014 UP amp 95 Down 2 X 7 16 X 7 8 Spacers HB Bracket 2014 UP amp 95 Down Wire Ties self adhesive clips 4
4. You should always be aware that this light should NOT be on if you are traveling at speed and Arming the system for deployment should only be attempted if the lower LED is Not Lit Please see the User Manual for more information on Proximity Sensor Failure The next thing to try is to make a turn from a dead stop with the wheels down As soon as you start the bike moving turns can only be made by using the handlebars The LegUp system is too strong to allow a great deal of lean with the wheels down If you need to make a turn shortly after departing from a stop raise the wheels manually left button and you will get complete control again The next thing to try 1s slow speed maneuvering with the wheels lowered If you keep your speed down most slow speed maneuvers can be accomplished with your feet up keeping in mind that at about 6 MPH the wheels will come up automatically Y ou can try full lock turns in both directions and the bike should stay upright with your feet up Understand it is always a good idea to keep your feet near the ground during these maneuvers if you can A mechanical failure or a wheel in a pothole could upset the bike Because the wheels are right behind your legs when they are down we recommend not trying to push with your feet to move the bike forward Use the engine and keep your feet out of the way this way the legs don t bite at your heels as the floorboard always have Backing up using your feet wor
5. landingear com pdf g2installhdfl pdf It may be easier to see some of the pictures in color there We are now ready to begin CONTROL SWITCH BOX NOTE ON pre 1996 models as well as 2014 and up models you will need a bracket to mount the switch housing which we should have supplied In this case remove the bolts that secure the clutch perch clamp on the left side install the supplied bolts through the bracket that has the box mounted to it through the supplied spacers and into the clutch perch Blue Loctite here Once tightened follow the rest of these instructions Control Box Plug If your bike requires no bracket as mentioned above remove the bolt on the top of the left switch housing on the handlebar Find the long chrome bolt thread it through the Control Switch Box insert the spacer on the bolt and with a drop of Blue Loctite and thread the bolt into the switch housing Square the box before tightening the bolt you may have to re align the mirror for clearance Route the wire inside the clutch lever and down the bar Use wire ties to hold the wire to the bar Run the wire through the top triple tree 1f you can to control it The idea here is to get the wires neatly to the front of the tank and routed under the tank It may be easier to remove the plug end and tape the silver plug ends together for this We have some pictures below to give you an idea of what this looks like On some bikes it 1s easier to loosen or
6. on the back of the air cylinder These press in relatively easy but a small tug will make sure the line 1s seated Guide the line through the hole in the mount as shown by the arrow at left We now need to guide that line over to the left side of the bike as we will be running it with the other line away from anything that might damage it OF g At right we have a picture of the line running under the right floorboard mount tied lightly to the floorboard mount Notice Ben is extending the leg so he gets the needed slack from the line and run under the right side cover area to get to the other side of the bike and joining the left line Get the line there any way you can just be sure that it 1s secure and cannot be damaged by anything hot or moving Once run you should mark the end with masking tape as RIGHT Take the other line insert it into the left cylinder as you did on the other side Mark the far end as LEFT and tie the marked ends together with masking tape so we can run them together Check Both Sides before we move on that by lowering and raising the legs there is plenty of slack for the lines Readjust your wire ties if need be but make sure they work properly to avoid headaches later 15 We want to run the lines behind or through the area under the left side cover Here Ben ties the two together on their way toward the back We want to guide these up to where the wire running along
7. the fender support is We like to tie two loose wire ties to that wire and run the air lines through them We will adjust and tighten everything a bit later The main concern here is to make sure the lines are run where they will be safe from the belt exhaust pipes or anything that could hurt them Here is a picture of the lines running along the bottom of the fender support being tied off to the big wire running toward the back You can tie them to anything you like as long as they are safe and out of the way Then you can start working back tying off the lines Tighten the lines z under the fender strut and just leave the end m Wild for now These are air lines so tie them off 3 snugly Careful though too tight could restrict the air flow Once we have everything tied up we want to make a loop with the extra line This will keep the lines the same length which allows the wheels to come down evenly and makes it easier to remove and install the bags Just take the lines as shown here make a nice loop and tie them off to each other Not too tightly as we want the loop to be able to move as you try to remove or install the bags Next we want to prepare the saddlebag This requires us to drill a few small holes to allow lines or fittings to travel through the bag to get to the compressor system 16 SADDLEBAG PREP HARD BAGS On one of the last pages of this manual you will find a drilling template for H
8. the lines you ran toward the back of the saddlebag Next put the bag on the support rail V3 tilted out toward you as shown here BW Attach the two small lines to the connectors from above keeping track of which is left and right Give a tug to make sure they are snug After the small lines are secure attach the big line to the fitting on the back of the air tank 1t may be helpful to push the extra small line back into the bag Again make sure the connections are tight Now attach the bag to the bike NOTE Once the system is operational in order to remove the bag you will disconnect the plugs we will be connecting later make sure the wheels are up pull the ring on the safety valve to let the air out of the tank then disconnect all three hoses and remove the bag Run the wire with the two plugs into the bag all the way toward the back just behind the end of the rubber gasket Find the computer and plug it into the big plug then plug the small plug into the wire from the compressor We will leave everything lying in the bag for now and clean it all up later In preparation for testing the system 1f you haven t already hook the negative battery terminal and the lead from our power connection up to the negative battery terminal On to Initial Testing don t worry that the proximity sensor is still lying on the lift 22 INITIAL SYSTEM TEST Turn your bike to Accessory Mode counter clockwise on Road
9. these to switched 12 volt orange and ground black Connect the Control Switch Box plug to its mating connector under the seat and plug the proximity sensor plug into its matching connector Don t worry the plugs only work one way you can t make a mistake here We need to find the fuse holder and the black wire with the hoop ends and get them to the battery These two wires run direct power to the compressor when it needs it This wire should already be under the seat area We want to connect the wire with the fuse holder to the positive terminal of the battery the battery cable should attach closest to the battery with this connector and any others attached after the battery cable as shown here Plan where you want the fuse holder so you can get to it if it is ever required Don t connect the black wire to the negative post yet We will when we are ready to test the system Depending on the year of your bike it may jook very different than the picture here Don t tie down the wires just yet we will clean up everything later Also leave the left electrical box loose 1f applicable until later as we will need to run air lines in this area Next we need to secure the wires that go into the saddlebag to the left fender rail and leave enough wire for the plugs to reach the computer and the compressor Start by getting the wire with the 2 big plugs on it run inside the left shock toward the back of the bike N
10. use a rotary burr but you could use a file or a small saw to cut the notch you see here What we want to have is a notch about 3 8 wide by about 3 8 deep This small slot will have no negative bearing on the weather tight nature of the bag but it will keep the wire from being hurt as you open and close the bag over time At the top of the bag about 1 to the left of the bail nut the bolt that holds the bag on is where you want to place the relief A bit left or right makes little difference but this wire goes down into a relief cut in the top of the compressor cover so the more accurate you are here the better Make sure that the wire when placed into the notch as at or below the top surface of the bag and you are go to go Skip the next section on Soft Bags and go to Install the Compressor Hard Bags 18 SADDLEBAG PREP SOFT BAGS On bikes with Harley soft bags Road King Customs amp Classics we have to mount the air tank outside the saddlebags due to how narrow the soft bags are Here you can see the tank on its mounting bracket This is a 09 later bike We supply two cad bolts with nuts and lock washers Secure the tank and mount as show with the relief valve pointed forward and the hose fitting pointed back and down On 2008 and earlier bikes the bracket looks a bit different and mounts with the valve down and the P 21M hose fitting ES pointed up as EJ shown in the second pic
11. Generation Ij n inar Tandingear con US PATENT 8 235 419 B Installation Manual Generation II Harley Touring Models 1988 Present Copyright 2015 Pete Giarrusso Inc D B A Chopper Design Services All Rights Reserved Table of Contents INTRODUC TION 5556999905005 3099055954085 5 55968 1X ERRARE 09080060 0o 50900 Se iS SR ESU RUE 4 bidsdie es ld 5 INSTALLA MON INS ERUC TIONS torti sss dao eroe tein 6 PREPARE FOR INSTALLATION 1 0 0 0 ccccsssscccsccnccccccccccccccccccccccceceeeeescsees 7 CONTROLS WEECH BOX serosesccascasscesecasesscecevassevecdseashasssucsacacsicencexeasezentsesatensiee 8 WIRING HARNESS m I 9 LEG amp MOUNT ASSEMBLED sissssssccstitescsassecsssssveccssoussesssctsteacasscscesesssscesveuees 12 RUNNING AIR LINE S socesvacssetewsseissstvacsiccecpescuenssiboncusscuussewacciecaaseseesssescoceusscusss 15 SADDLEBAG PREP HARD BAGS sssssssssssssssesseseseseceeeeeoooooosssssssssseeeeeeeeeseeee 17 SADDLEBAG PREP SOFT BAGS sessssssssssssessseeeeseececececooosssssecoceeeeeeeeeeseeeeeeee 19 INSTALL THE COMPRESSOR HARD BAGS sccscsssssscecceeceeeeeee 19 INSTALL THE COMPRESSOR SOFT BAGS eere 21 MOUNT PROXINITY SWEL C H ororaccinercme nonr s 24 BIKES WITH PULDEY BOLI Sie E R 24 BIKE WITH NO PULLEY BOLTS CUSH DRIVE ssssssssssssssssssesssssssssssssssssssssssees 25 FINISHING UE iiir i EEEE ATi 28 FINAL ADJUSTMENTS amp MAINTENANCE MODE ssesseseeseerees
12. Kings all the way right on other models Your speedometer should illuminate and if everything 1s working properly the compressor should turn on for about 6 seconds to fill the onboard air tank At this point have a look at the yellow proximity sensor The RED LED ON The Sensor Should Not Be Lit Take a metal object screwdriver wrench etc and hold it on the flat face of the sensor it has a circle embossed in it The LED should light up and go out when you move the metal away If not check all your connections Next press the rightmost pushbutton on the handlebar switchbox and hold it for at least 3 seconds One or both LEDs on the switch panel should light up or blink we really don t care which at this point If this occurs you are doing well If both LEDs are flashing maintenance mode you can skip the next step which is to press both buttons until both LEDs flash Next press both buttons again for just an instant If everything 1s working the bottom or yellow LED on the switch box should flash and the top LED should be out The next step requires some care If the bike is still on the lift have a helper hang on to it as you touch the left button for just a split second The legs should move down likely until the wheels hit or miss the lift and they do this VERY quickly Again be careful as they could lean the bike if one wheel touches the lift and the other does not Press and hold the right button and they should
13. angle for the bracket that will allow the rotor bolts on the brake rotor to pass by the proximity sensor in the middle of the square portion of the sensor When you think you have it turn the ignition to Accessory position and roll the wheel to make the bolts pass by the sensor Each time one passes the sensor the LED on the sensor should go bright then off 2 If this is not happening you may need to get the sensor a bit closer to the pulley bolts SMM is a very small distance If you have to move the sensor closer you may have to shim the back of the bracket or bend it just a tad No matter what you need to do you MUST make sure that as the wheel turns the light works as described above Once you are certain tighten the shock bolt and test it again Rotate the wheel past all 5 rotor bolts and make sure the light blinks and goes out each time If all is perfect you are done The automatic retraction of the legs as well as their deployment RELIES on this sensor being placed perfectly Now we can route the wire 29 WIRE ROUTING Tie the Proximity sensor wire down the left side of the swing arm for pulley bolt bikes or the right for Cush drive bikes Use the supplied self adhesive tabs to secure the wire snugly to the swing arm Just make sure you route this safely and tie it off securely Finally pull all the extra wire under the seat area Your wire from the handlebar should already be under the seat tied off to the
14. ard Bags Carefully cut the template out making sure it 1s to scale and tape it to the inside of the left saddlebag as shown The saddlebag is curved so just bring the straight lines to the edges where they start to curve and you will be fine There is a margin of error here so don t worry Use a small bit to start 1 8 of so and drill through the pilot hole on the template Once these are done the final drill size is 3 8 or 2 depending on the fittings we supply 2 different sizes from 2 different vendors If you are unsure drill a 3 8 hole if it is too small move up to 2 Once the holes are in place find the bulkhead fittings The 90 degree part stays on the outside of the bag with the straight part inside Start with the lower hole and tighten the fitting No reason to make it too tight there is no chance for leaks here and the elbow spins to make it easier to attach the lines Once the bottom fitting 1s in place install and tighten the top fitting Now the bag is ready It is time for a test fit Put the saddlebag on the rail and lean it out as shown here Find the line you marked as xw right and insert it in the bottom fitting the other in the top fitting Now attach the bag and make sure the lines are in no sort of bind or in danger of being damaged by anything at P The last thing we need to do 1s create a small notch for the wires to get through when the bag is closed We
15. are the responsibility of the purchaser Defective parts are to be returned to Chopper Design at the address below Purchaser must contact Chopper Design to receive a Return Material Authorization prior to returning defective parts to Chopper Design Abuse improper installation or use collisions or accidents are not covered under this warranty Replacement parts for this type of damage are available through Chopper Design Users of the LegUp system agree that Chopper Design is NOT responsible for personal injuries or damage to property arising from the use of the system While we believe this system to be safe and reliable the user is advised that use of LegUp is done so at the users own risk Use of the system implies agreement to the above statements If you can t agree with the above Chopper Design and its dealers would be happy to refund your full purchase price before you install the LegUp System Chopper Design Services 1365 Bennett Dr 101 Longwood FL 32750 407 834 5007 LegUp LandinGear com Installation Instructions The LegUp system has many components Pleased be sure you have them all before starting your installation COMPONENTS 1 Wire Harness W Switch Box 2 Leg and Mount Assembly L R 3 On board Computer Module 4 Proximity Sensor 5 Saddlebag Mounted Compressor System 6 Hardware Bag If you believe you are missing any parts please contact Chopper Design at 407 834 5007 and we will rectify the situati
16. ce Mode is needed Sit on the bike and hold it level If both lights on the switch box are flashing the system is in maintenance mode If not PRESS amp HOLD both buttons until all lights flash Do your best to press both buttons at the same time so the system doesn t respond to what it thinks is a request to lower the legs Once flashing hit both buttons for an instant to get the system in the DOWN setting mode lower yellow LED flashing Touch the left button briefly the wheels should go down immediately This is VERY quick don t be startled Using very short pushes of the left button press and then feel the stability of the bike If it feels firm enough try leaning the bike a bit If the wheels return the bike to upright there is likely enough pressure Put your feet on the floorboards the bike should stand on its own Rock the bike a bit left and right being prepared to put your feet down If the bike continues to come back to upright the DOWN stop is now set and we can move on Hit both buttons for a moment to get into the UP stop mode Usually hitting the left button just before the right assures that air 1s not released The top LED should now be blinking Press and hold the right button to raise the legs Listen as the air evacuates once it is quiet let go of the right button The UP stop 1s now set Hit both buttons when complete Both LEDs should light and you are done with these adjustment Now press the le
17. damaged gi D t WT S sje on Oe 2 T a 27 FINISHING UP Now it is time to reinstall everything you took off and do final checking of everything Reinstall the seat making sure all your wires are routed neatly tied off nicely and don t interfere with the seat installation Once all of this 1s accomplished we should get the bike on the ground and with a helper cycle the wheels up and down a few times having your helper make sure the air lines are not being scuffed or are over tight and that the wires are out of the way of anything that could damage them Double check all your bolts for tightness Now we can dial in the legs and adjust the wheels if needed LEAKS This system uses air and air loves to leak The fittings we use are tested for leaks before shipping but we have a few simple tests to make sure you have no leaks or just insignificant ones if any set the wheels down and leave the system on Put the kickstand down and turn the bars all the way left If the compressor makes noise more than once every two minutes you may have a leak at the lines that connect to the compressor or the tank fittings Some soapy water will tell you where you will need to remove the compressor top to test for these leaks Assuming the compressor doesn t lose enough air to kick on after 2 minutes you should be fine You can turn the bike off and wait to see if in 5 minutes the bike is not as stabl
18. e adjusting anything We try to get enough information from you before shipping our systems so we can setup the product for you before it 1s shipped Also 1f you do the measurements we show you below you can contact us and we can likely tell you how to change the setup to match your bike Before we start make sure the floorboards are set to their highest position Ideally we want the bottom of the board mount at a height of between 13 amp 14 25 Measure this from the small donut on the bottom of the board mount in the center of the board with the bike held level we set the bike on a jack here but you can have someone try to hold it upright if need be We suggest taking this measurement from both sides and dividing them in half Armed with this info we can use the list below to find a good starting point to set the wheels up properly e FLH 14 5 One from Back Strap Up e FLHX 13 3 4 Two from Back Strap Down e Low Bike 13 1 16 One from Back Strap Down Wheel On High Hole Strap Up or down refers to the strap that holds the wheel holders together One or Two from back refers to the bolts that are used to lock the wheel holders into position as it is pivoted around the big axle Wheel on High Hole or Low Hole Default refers to where the wheels are mounted on the wheel holder We also have two holes at the top of the wheel holder that can be used for a bike that is VERY low On the next page we show you the whe
19. e as it was when the wheels were first lowered If it lasts the 5 minutes and is still very stable you could still have a leak but not one that would be a problem on the road Leave the bike on its wheels overnight again kickstand down bars full left in case the legs lose a lot of air the bike will land on its stand If in the morning the bike is still stable you have no leaks If there are leaks the fittings on the air cylinders would be the first for the soapy water check with the two small line fittings on the compressor next If you need help with these please feel free to call us at 407 834 5007 28 FINAL ADJUSTMENTS amp MAINTENANCE MODE The next two sections are typically NOT needed We include them to document your system thoroughly but MOST people will never need to use either section MAINTENANCE MODE NOTE Maintenance mode is a procedure that TEACHES the computer how much pressure to use when it lowers the wheels and how much pressure to release when raising the wheels We always set this at the factory ALWAYS We include this procedure in case it is ever needed in the future Please skip this section unless you have been instructed to reset the system by Chopper Design Turn the ignition to Accessory and start the LegUp System hold right button for 3 seconds The system should be set at the factory for proper pressure but some wheel adjustment may be needed If it has been determined that Maintenan
20. el holders which should help clear up any confusion you may have about the wheel holders and their adjustments 32 big Ade igh ypical Sirap Up Adustment moles CLERC lt x TUA 14 7 BI Y Cr rA Dd UN D 2 Py a A is Tine j Ip je 1 ia 4 E a t i A NN ew 7 da P ESL E i y Big AX IG e LOW s Be aer ie very low bikes On each supporting leg you will find two bolts down near the end by the wheels The two bolts control the angle of the Wheel Holders By moving the wheel forward or back we can tailor the length of the support arms to a particular bike A helper is handy here Make sure the wheels are up Make note of exactly which two holes the bolts are in Loosen the locking nuts from the back and remove the bolts you will notice the Wheel Holder can pivot on the big axle bolt Starting on the left side of the bike move the bolts one hole counter clockwise Go to the right side and move them one hole clockwise Loosely fit the nuts no need to final tighten them at this point Lower the legs Is the bike more or less stable If it is more stable and you can sit on the bike and rock it back and forth without it leaning over you are done If not remove the bolts again and move them in the opposite direction two holes and retest If everything is fine final tighten the lock nuts and you are done If you need to you can move the wheels from t
21. ese are only suggestions run the wires anyway you like your existing connections to power will remain as they are One caveat 1s that the plug that used to run to the actuator will have no plug in it This should not be a problem assuming it is stored in an area that does not get very wet When reading the install manual you should be able to ignore most all instructions having to do with wiring and you will NOT need to do the proximity test by rolling the bike as this should remain mounted If you have any trouble with this upgrade please give us a call at 407 834 5007 37 ILLUSTRATIONS Proximity Sensor 5 sensor side Compressor Plug Plug Biack Hames side Brown Sensor pide Crange Harnesr pide SADDLEBAG DRILL TEMPLATE HARD BAGS Print and Cut out Make Sure Dimension is Correct Some printers don t print to scale 5 0000 6 0000 SADDLEBAG DRILL TEMPLATE SOFT BAGS Print and Cut out Make Sure Dimension is Correct Some printers don t print to scale 6 1250 4 7300 40 HARDWARE LIST 4 3 8 16 X 1 5 Chrome Allen Bolts Leg attachment 2 5 32 Black Air Line 5 Foot long 2 5 32 Black Air Line 2 Foot Long Valve to Bulkhead or Unions 2 5 32 90 Degree Bulkhead Fittings Hard Bags Only 2 5 32 Union Fittings Soft Bags Only 2 5 16 18 X 74 Hex Head Bolts with Nut amp Lock Washer Soft Bags Only 1 14 Air Line 2 Foot
22. eseeeseeesseeseeesseeessees 29 MAINTENANCE MODE sororia ra n a ed EH e ette 29 WHEELADJUSTMENT ione enesenn er par N EEAS 30 TES CRID uec 35 GENERATION I UPGRADE INSTRUCTIONS 37 IUEUSTRATIO NS 555 2 61 CUIR Du Sata SENE ERE RS Ee Pru EE DUE REv VP a 38 SADDLEBAG DRILL TEMPLATE HARD BAGS 39 SADDLEBAG DRILL TEMPLATE SOFT BAQGS 39 HARDWARE EDS T osisessvestea 9i i05 oi eo NER CE Sora 011000006009i 00x00 0 S eodd 41 Introduction This manual covers installation of the Generation II LegUp LandinGear system by Chopper Design Services This system should only be installed by a qualified technician or those with above average mechanical skills If you are not SURE that you can perform this installation please contact us and we will help you find a qualified shop to assist you While the Generation II System holds your bike upright very well you are STILL responsible for balancing the bike The system WILL relieve you of some of the weight of the bike and help you avoid balance problems as you approach a stop maneuver at slow speeds and back the bike up Improper installation will void your warranty so please be very careful Thanks for choosing LegUp Warranty Chopper Design Services warrants the LegUp system for a period of one year from date of purchase This warranty covers replacement parts and or manufacturer defects Incidental damages or costs
23. ext measure 10 inches back from the 12 pin biggest plug and mark the wire We are trying to make sure we have all the wire we need but not too much extra Run the wire under the chrome fender support and tie it off to the two fender supports 2009 and later bikes look like the picture at left on others it will look a bit different just make sure you leave the wire needed and tie it off securely and out of the way of anything that moves or could hurt the wire No Matter how you need to secure the wire make sure you have 10 inches of wire sticking out from the end of the fender support to allow us enough wire E to get what we need into the saddlebag You can now pull the extra wire back into the under seat area Later we will be securing air lines to this wire so make sure that will be possible with your choice of how to attach this wire The only wire left dangling should be the proximity sensor and mount and we will handle that soon 11 LEG amp MOUNT ASSEMBLIES IMPORTANT All Harley touring bikes MUST have Harley Rear Floorboard Mounts Part 49349 07 and other part numbers for earlier model 50379 07B which is a kit with mount boards and hardware to install the Generation IT System Street Glides and some Road Glides are equipped with pegs and NOT Floorboards These mounts and optional floorboards are available through your Harley Dealer or can be purchased through Chopper Design Also Verify that the flo
24. ft button and the legs should lower again this is fast and loud The bike should be held up firmly Hit it again and the legs should retract If you are satisfied with these limits you have successfully installed the LegUp System 29 WHEEL ADJUSTMENT The LegUp GEN II system is typically set up at the factory for the height of your bike The system is VERY height dependent If after testing the initial installation the bike does NOT feel stable the wheel system MAY need to be adjusted to the height of your bike AGAIN we normally ask at order time if your bike is at stock height and we set the system up for whatever height you have furnished us DO NOT make any changes unless the stability we expect is NOT present If you feel you need to adjust the height length of the wheel holders please read this ENTIRE section before starting the process If you need help please contact Chopper Design at 407 834 5007 If you are happy with how stable the bike feels you can skip this section and move on to a test ride If you are not sure or you skipped maintenance mode as instructed a good test 1s to bring the wheels down put the kickstand down and lean or try to the bike on its kickstand while sitting on the bike If the bike comes back to center without your help or you put your feet on the boards and can bring the bike up by just leaning to the right move on to the next section Test Ride the wheel settings are fine The stability of
25. handlebar neatly from the switch to the triple tree and secured safely under the tank Now is a good time to tie up all the wires under the seat First make sure you have all excess slack pulled under the seat We loop our wires tie the excess as a bundle make sure they don t interfere with the seat and tuck them in as shown here We need to make sure the compressor plug 1s attached and tucked in as we install the top Find the L shaped metal top that you removed from the compressor earlier The top mounts with the two holes toward the back of the bag with the single hole toward the front It is a tight fit so slanting it into the bag is best As you work the top over the 3 aluminum standoffs make sure the computer and plug sometimes it is easier to unplug the computer until the top is set are coming through the curved cutout Hard Bags only as the plug and computer will sit on top of the compressor system Once the top is fitted find the 3 nylon nuts and screw them on the three posts to secure the cover These are plastic nuts so no wrench is required here 26 When complete you want to Velcro the computer onto the top and make sure the plug the compressor plug stays UNDER the top and wires look something like this The top picture shows a hard bag while the bottom shows a soft bag Our main concern here is to give you as much of the saddlebag as possible and make sure the wires and components are not going to be chaffed or
26. he lowest hole up one hole You can remove the wheel holders turn them over strap up instead of down for example and install them on the other side of the bike You can move the big axle from the low to the high hole All these techniques take patience but allow significant flexibility to tailor the system to your bike On the next page we show you some examples Normally you do not need to do ANY of these adjustments but if you need to we wanted to teach you the methods at your disposal 33 The picture below left shows the wheel holders set up for touring bikes with full length shocks Electra Glides etc The one at right is set up for lowered bikes Street Glide and others Notice how the curve of the left one 1s toward the front of the leg and the curve on the right one is toward the back This small change can make a big difference in how stable the bike may be If you are having trouble getting the stability you need you can remove the 2 small and the one large bolt that connects the wheel holders to the legs and swap them from one side of the bike to the other This will reverse the direction of the wheel holders and keep the wheels aligned properly Again this is only needed if you are not getting the stability we describe above Below 1s a picture that shows the angle of the actuator when the wheels are set properly Notice the bottom DE the chan e inside the black legs is further forward than the top Yours 7 should
27. ks fine and the chore of balancing the bike 1s taken care of for you Practice practice practice Enjoy your LegUp System 36 GENERATION I UPGRADE INSTRUCTIONS NOTE Read this before starting your installation if this is an upgrade If you are upgrading from a Generation 1 system most all the instructions in this manual pertain to you but some do not The most important thing is to NOT take your wiring harness off the bike We should have supplied you with an upgrade harness that will allow you to keep most everything as it was and adapt the wiring to the new system The second VERY important thing 1s that your computer MUST be sent in for upgrading or it will not work with the new Generation II system With those facts 1n hand let s get to 1t We will assume you have already removed all your Gen I hardware The legs the actuator mounts the mounting plate All you should have left from the old system 1s the wiring harness The upgrade harness plugs into where the old computer plugged in This is a 12 pin plug on the opposite end of the upgrade harness from the two plugs that are close together Once this 1s plugged in we like to run the wire with the two plugs along the bottom of the bag back to the compressor The thin wire with the fuse holder T on it gets run back toward the seat area to get connected to the bins i You can tie this up to o the existing harness wires along the route back to the battery Th
28. look like something like this Also notice that the floorboard is level We have seen one bike that had floorboards that leaned forward which would RUIN the geometry required here Please verify that your floorboards are level If you are still not getting the stability we describe here please call us and we will try to determine why not 407 834 5007 34 TEST RIDE Get the bike to a clear paved mostly level area where you can test ride it Start the bike turn on the LegUp system and lower the legs The first test should be done in a straight line Put the bike in gear and slowly accelerate You may notice that the bike tends to want to steer a small amount left or right This is normal unless it is severe Effectively you are driving a trike and steering is done with the handlebars NOT by leaning Once underway we recommend you keep your thumb near the left button and press it to raise the wheels if there are any surprises the top LED should flash at around 6 MPH meaning the legs are retracting It 1s difficult to lean on one wheel or the other as you leave so you may wish to raise the wheels manually if the bike 1s steering due to uneven pavement Assuming the legs are retracted you should try to deploy the wheels As you come to a stop the Green LED should be on As you slow down almost stopped the Yellow LED should illuminate at the proper speed Once it does sometimes hard to see hit the left button and put your fee
29. move up Again with the bike on the lift you have to be very careful here If all of the above has occurred great If the legs are not all the way up press and hold the right button until the legs stop and turn the ignition switch off The test is now complete Let s move on to mounting the Proximity Sensor 23 MOUNT PROXIMITY SWITCH This step is crucial Understand it before starting The proximity sensor tells the system how fast the bike 1s traveling The proximity sensor mounts to the swing arm at the rear pulley Depending on the year of the bike it will mount 5MM from the pulley bolts or we will be attaching metal squares to the face of the pulley No matter what type of pulley is on your bike you need to jack up the rear wheel so we can spin it to test the sensor and its placement Make sure the bike is in neutral BIKES WITH PULLEY BOLTS With the bike up as described above turn the ignition switch to the accessory position The LED on the sensor should be out Place the mounting bracket on the swing arm and line it up to where the main part of the sensor is aiming at a dun Don and is centered on it you may have to turn the wheel to do this What we are looking Fi for is for the LED to go bright and OFF asa pulley ME bolt passes the sensor Play with this by rotating the wheel back and forth while holding the bracket in place Once you feel you have the right place hold the bracket steady and slowly rotate the wheel
30. on Some of the parts are shown below PREPARE FOR INSTALLATION IMPORTANT All Harley amp touring bikes MUST have Harley Rear Floorboard Mounts Part 49349 07 and other part numbers for earlier models or 50379 07B which is a kit with mount boards and hardware to install the Generation II System Street Glides and some Road Glides are equipped with pegs and NOT Floorboards These mounts and optional floorboards are available through your Harley Dealer or can be purchased through Chopper Design Factory Saddlebags must remain on the bike to house the compressor system While the Generation II 9 is able to be installed with MANY aftermarket pipes Chopper Design can only guaranty fitment on stock motorcycles IF YOU ARE UPGRADING FROM A GENERATION I SYSTEM PLEASE READ THE ADDENDUM TOWARD THE END OF THIS MANUAL ON THIS SUBJECT FIRST Please do not let the size of this manual intimidate you We cover many different bikes and circumstances here and we feel that more pictures and more detail can only help someone trying to install our systems Better to have the details than want for them Place the motorcycle on an acceptable bike lift You will need to keep the bike on its wheels for most of the installation and Jack the rear wheel off the lift for some portion of the installation Make SURE the motorcycle is secure on the lift Remove the seat and disconnect the negative cable on the battery This manual is available at http
31. orboards are LEVEL Left to Right Boards that lean forward will reduce the effectiveness of the LegUp System Now we need to mount the Legs under the passenger floorboards Before you do make sure the rear floorboards are at their highest position In many cases the factory mounts them one hole down from their highest spot We want them as high as possible to give us the best ground clearance Sometimes you will find a plastic plug in the upper mount hole Remove this if needed and move the boards up MOUNT The Legs Next we want to mount each of the leg assemblies and we start by putting some blue Loctite on the supplied Allen bolts putting the bolts into the top mount and laying the mount on the floorboard mounting arm as seen here Once the top mount is in place we can mount one of the legs NOTE If you have a 2010 or later bike or floorboard mounts that have 2 bolts rather than a bolt and a locating pin these top mounts will have a bevel machined into the bottom slot Make sure you orient the high side of this bevel toward the inside of the bike this will become clear as you try to mount the leg These top mounts should be level on the floorboard mounting arm If you have arms as described above and your mount does not have the bevel to match please contact us and we will swap it with the proper one for your floorboards The board to the left below one bolt and a locating pin uses the FLAT top cap and the boa
32. rd on the right two bolt mount uses the BEVELED top cap You can see how much higher the inboard edges of this mount are and why it requires the machining of the bevel The Leg Mount system is heavy so you may want to get a helper here Ben has done this so many times he does it by himself but you will likely appreciate an extra hand The mount has cutouts that fit tightly to the underside of the floorboard mount Find the mount for the side of the bike you are on and offer it up to the floorboard mount feeling the obvious spot it fits into Start tightening the Allen bolts a little on each side Shortly the majority ofthe weight will be held by the bolts You need to get this very tight but must alternate so the mount stays even When you are done you should have the smallest gap on each side of the top mount and they should be about the same It 1s imperative that you make sure the mount is in the right place and that it 1s tight The picture below shows the bottom of the floorboard mount note how the leg system is even and snug against that mount Give it a tug it should be very stout If it is install the other side in the same fashion and we can move onto running the air lines 13 14 RUNNING AIR LINES We need to route the air lines from the cylinders to the area near the left saddlebag You should find 2 long air lines of identical lengths On the right side of the bike press one end into the fitting
33. remove some of the tank mounting bolts Make sure the wires do not interfere with anything under the tank and that there 1s nothing that would scuff the wires Once the wires are under the seat area you can assemble the plug if disassembled according to the diagram above WIRING HARNESS NOTE If you are upgrading your existing Generation I system please read the addendum on this upgrade at the end of this manual before continuing with the wiring harness The next step is to route the wiring harness The harness and the plugs are routed mostly under the seat Different models have different amounts of space in this area and all the wires are long enough to allow you to place the connectors in the best place for your bike Remove the left side cover amp saddlebag We need to make room for two big plugs to come through the seat area toward the left saddlebag On later model bikes this means removing the Torx bolt that holds the fuse box under the left side cover On earlier bikes there is more room in this area and nothing needs to be removed Find the two BIG plugs on the harness 12 pin with an 8 pin pigtail attached and slide them through the seat area and out just below the left fender support Leave the remainder of the wire harness under the seat for now Once both plugs are through you can pull most of the slack out We will be pulling these plugs back toward the back end of the saddlebag behind the shock The pl
34. s not come with rear floorboards much like the Street Glide so Harley or aftermarket boards MUST be installed In order for the LOW to work as well as other bikes we have to use our adjustable wheel holders It may be hard to see here but we move the wheel axle up to a second hole 1 and the big axle at the top is set at the lower hole 2 These two changes make the legs shorter to offset the low height of the bike The floorboard needs to be in the highest hole The bolts that orient the wheel holder need to be in the third and fifth hole from the back They also need to be threaded through the hole that is second from the back on the wheel holder 3 If you told us you have an Ultra Low this is how we would configure the system before shipping We just furnish this info to document the setup IF YOUR BIKE FITS ONE OF THE THREE SCENARIOS WE HAVE DISCUSSED ABOVE IGNORE THE NEXT SECTION WE DO EVERYTHING WE CAN TO SET THE SYSTEM UP BEFORE SHIPPING F YOU ARE NOT SURE PLEASE CONTACT US BEFORE ADJUSTING THE SETTINGS OUTLINED BELOW IF YOU HAVE A REMOVEABLE LOWERING KIT INSTALLED YOU MAY WISH TO CONSIDER REMOVING IT AS THE NEED SHOULD BE REDUCED SIGNIFICANTLY BY THE LEGUP SYSTEM 3l We now have designed wheel holders that allow SIGNIFICANT adjustment to make the LegUp system match the height of your bike perfectly The adjustments can take time to get perfect so be patient and understand this section befor
35. t down near the ground The top LED should flash and the wheels should deploy almost instantly underneath you Make sure you are ready to balance the bike though you likely won t have to Immediately after the wheels touch the ground the bike should be supported reasonably but the cylinders can take up to 6 seconds to get completely filled Make sure you balance the bike as this occurs The slower you are going when deploying the wheels the smoother the transition will be from wheels up to wheels down Practice these maneuvers until you are comfortable with the wheel adjustments and the system operation SEMI AUTOMATIC DEPLOYMENT Another way to deploy the legs is semi automatically First we must be SURE that the proximity sensor is working properly or the wheels could come down at higher speeds than we wish If you are travelling at a speed over 10 MPH AND the yellow light bottom on the handlebar control is out hit the left button The bottom or yellow LED should start to flash When you slow down to around 5MPH the wheels will deploy see the red green flash on top LED Again prepare to put your feet down IF the lower LED is lit at a speed over 10 MPH don t hit that button see caution below NOTE The bottom LED Should not be LIT SOLID if the bike is travelling over I0MPH In the event it is the wheels will deploy instantly if you try to set them as above this is dangerous You MUST re visit the sections on testing the proximity sensor
36. the GEN II LegUp system relies on the pneumatic actuator when deployed being at an angle that is forward of perpendicular for best results Different bikes are at different heights and Chopper Design uses an ingenious method to adjust the length of the supporting legs to maximize the stability it affords Typically we will send the Leg Assemblies set up for the bike you told us you had We have three different Standard setups for the Harley Touring bikes standard FL Height Street Glide and other bikes using the Harley bend shocks and the new Ultra Low models The first picture above shows the setup for standard height Harleys The boards are set in the highest position the wheel holder is set with the strap facing up and the small bolts set in the second and fourth hole from the back of the leg Notice curve of wheel holder This is how we should have sent the legs to you if you told us you bike was at stock height At left we see a setup for a Street Glide or other bikes with the Harley Lowered shocks The small bolts are again set in the 2 and 4 holes from the back and the strap that holds the wheel holders together is on the bottom of the leg You can tell because 30 the curve of the wheel holder is the opposite of the first picture The floorboards should be set at their highest position as well for these bikes This last picture below shows the setup for the new Ultra Low This bike doe
37. to the negative battery terminal don t worry that the proximity sensor 1s still lying on the lift Skip the next section on Soft Bags and jump to Initial System Testing 20 INSTALL THE COMPRESSOR SOFT BAGS First we need to remove the top as it won t be needed until the very end We do this by removing the three nylon nuts on the top of the plate These are only hand tight and will be put back on without any tools as well Notice that the compressor has two long feet these fall into the well in the soft saddlebags Once the top is off the compressor should look like the picture below Now we need to install the compressor into the bag The fit is tight and the bag is flexible so take your time here The picture at left shows us starting the compressor into the bag As we do this we take the 1 4 Fat line and start it through the lower hole you drilled into the bag and start the two 5 32 hoses Thin through the upper hole Keep track of which line 1s the left line so you can attach it to the line that goes to the left wheel later Once the compressor is nestled into the bag it should look like the picture at right Make sure the system 1s pushed all the way to the back of the bag and feels sturdy in its new home Next we will install the bag and attach the lines 21 We need to find the inline connectors white in this picture could be a different color and attach them to the end of
38. ture It uses two existing bolts as shown for 4 mounting Whichever type of mount you have once the tank 1s mounted solidly we can turn our attention to drilling the two holes required in the saddlebag These holes allow the air lines to ect in and out of the E saddlebag and m allow easy od of the bag First we need to find near the end of the manual the drilling template for soft bags Carefully cut this template out and tape it to the inside of the left saddlebag as seen in the next picture The flat bottom of the template lines up with the bottom of the bag just before it turns under while the curve should fit nicely as seen here The upper left angle should fit inside the line where the leather meets the hard back There is a margin for error here so be careful but not paranoid Once placed drill using a 5 16 bit each of the holes on the template Skip to the section on installing the compressor Soft Bags 19 INSTALL THE COMPRESSOR HARD BAGS NOTE If you have soft bags Road King Customs amp Classics skip to the next section Install Compressor Soft Bags Find the compressor as shown here We need to remove the top as it won t be needed until the very end We do this by removing the three nylon nuts on the top of the plate These are only hand tight and they will be reinstalled without any tools as well Once the top is off the compressor should look something like the picture below
39. ug from the Proximity Sensor 3 wire needs to routed under the seat as well If you have Pulley bolts on the drive pulley 07 earlier bring the plug up on the left E side where the big plugs just went through If you have a Cush TM bike 08 later bring the wire up through the PER side c cover and under the seat At this point just route the wires into the a m general area and plan where you would like to tie them up safely The Proximity sensor is not mounted yet because we need to have power to make sure it 1s placed perfectly so just route the wire for now You can collect any excess wire under the seat area when amp the time comes Disconnect the fender plug under the seat and plug the double white plug in between the plugs from the bike On some 2010 and later bikes FLHX FLTR the fender plug 1s not like the one shown here so we plug into the MEE connector instead The picture below shows this connector under the seat below the ECM Remove the rubber plug and plug the four pin with just two mw wires orange black into the bikes accessory connector The double white plugs we talked about above will NOT be found on your harness Later Models 21014 UP have a 8 pin plug under the left side cover We will supply you with the plug for your bike you just have to find where the factory hid its mate NOTE If you have a pre 1996 bike you will have two wires no white plug and will need to connect
Download Pdf Manuals
Related Search